Home/Catalog/CISCO-ASN-GATEWAY-MIB

CISCO-ASN-GATEWAY-MIB

AI MIB Summary

The CISCO-ASN-GATEWAY-MIB provides SNMP management for Cisco WiMAX Access Service Network Gateways (ASN-GW), enabling monitoring of R6 interface signaling and data paths, subscriber sessions, service flows, and Base Station associations. It facilitates the tracking of critical QoS parameters, tunnel states (GRE/DPID), and mobility events such as handovers between Base Stations and ASN-GWs within the IEEE 802.16 architecture.

This module manages Cisco's WiMAX ASN Gateway (ASN-GW). A WiMAX network supports wireless data communication through WiMAX radio (802.16) technology. The high level architecture of a first generation WiMAX network with the respective protocols for each interface is shown below: ++ | R2 | ++ ++ | | | R1 | | R6 | | | | MS || BS |-| ASN-GW | | | | | | | | ++ ++ | | | | | R3 |-| R8 | R4 | | | | | |-| ++ ++ | | | | R1 | | R6 | | | MS || BS |-| ASN-GW | | | | | | | | | ++ ++ R2 | | | ++ The diagram below depicts the relation of the subscriber to the session and flows: ++ -Flow (connected via data path) | ASN-GW | - Subscriber -Session -Flow (connected via data path) ++ | -Flow (connected via data path) | -Flow (connected via data path) | + A subscriber initiates a call from a MS. A session is created between the BS and the ASN-GW for that call. Multiple flows can be created for the session with different QOS parameters. For example one flow can created for a voice stream and another for data. Data paths are created between the BS and ASN-GW to forward the data packets of the created flows. When the first subscriber from any MS connected to a BS initiates a call via the BS to the ASN-GW, a signaling path is created between the BS and the ASN-GW. There is only one signaling path between each BS and ASN-GW. Signaling paths and base stations can be used interchangeably. The signaling and data paths remains active as long as there are subscribers connected to the ASN-GW from any MS connected to the BS. If a path has no session/flow connected, it will be purged after a certain period of time. This situation can occur when all subscribers on a certain path are disconnected. A subscriber disconnecting from a certain path does not indicate that the subscriber has left the network, it could simply be handing off to a different path. The IP addresses of the signaling and data paths can be the same or different both in the BS side and in the ASN-GW side. ++ ++ | Base | | ASN-GW | | Station| | | | | SigPath | | | IP(B1)|<............>|IP(A1) | | | | | | | | | | | DataPath 1 | | | IP(B2)|<............>|IP(A2) | | | | | | | DataPath 2 | | | IP(B3)|<............>|IP(A3) | ++ ++ Relationships: Base Station 1 to many Mobile Stations ASN-GW 1 to many Base Stations Subscriber 1 to 1 Sessions Session 1 to many Flows Datapath 1 to many Flows Signaling Path 1 to 1 Base Station Acronyms and terms: AAA AAA refers to a framework that specifies the protocols procedures for authentications, authorizatitin and accounting associated with the user, MS and subscribed serviced. AGW ASN-GW ASN ASN (Access Service network) is defined as a complete set of network functions needed to provide radio access to a WiMAX subscriber. ASN-GW ASN-Gateway is a logical entity that represents an aggregation of Control Plane functional entities that are either paired with a corresponding function in the ASN (for e.g BS instance) a resident function is the CSN or another functions in the ASN. For every MS, a BS is associated with exactly one default ASN-GW. However, ASN-GW functions for every MS may be distributes amongst multiple ASN-GWs located in one or more ASNs. The ASN-GW utilizes Session Redudancy to ensure a backup ASN-GW is available in case the primary ASN-GW goes down. BS Base Station is a logical entity that represents an aggregation of Control Plane functional entities that are either paired with a corresponding function in the ASN (e.g. BS instance), a resident function in the CSN or a function in another ASN. The ASN-GW may also perform Bearer Plane routing or bridging function. BSID The Base Station Identifier is a global unique identifier for a WiMAX base station. CPE Customer Premise Equipment. CSN CSN (Connectivity Service Network) is defined as a set of network functions that provide IP connectivity services to the WiMAX subscribers. Data Path Corresponding to each subscriber, data paths are created to foward packets between the ASN-GW and the subscribers. DPID Data Path ID is used to identify the tunnel carrying MS traffic between ASN gateways or between the ASN gateway and base station. As of 8/28/07, only the GRE key is to be used as the DPID. Flow A service flow is a unidirectional logical flow between the network and the Subscriber Station. A service flow is created to handle a different QoS over the connection oriented MAC. A subscriber can have multiple service flows associated and each service flow is associcated with an uplink and downlink classifier. GRE Generic Routing Encapsulation. Refer to RFC 1701 for more details. LB Load Balancing Messages Messages are packets exchanged on the signaling paths. MS The Mobile Station is a generalized mobile equipment set providing connectivity between subscriber equipment and a base station (BS) The Mobile Station may be a host or a CPE type of device that can support multiple hosts. MSID The Mobile Station Identifier is the 802.16 identifier used for all subscriber stations, and is used in all the messages over R6. The identifier associates all requests from a mobile to the ASN-GW. Packets Packets are datagrams fowarded over the data paths. R1 Communication protocol between mobile and BS as per the air interface (PHY and MAC) specifications (IEEE P802.16d/e). R1 may include additional protocols related to the management plane. R2 The interface between the MS and CSN associated with Authentication, Services Authorization, IP Host Configuration management, and mobility management. This is a logical interface thus does not reflect a direct protocol interface between MS and CSN. R3 The interface between the ASN and the CSN to support AAA, policy enforcement and mobility management capabilities. It also encompasses the bearer plane methods (e.g., tunneling) to transfer IP data between the ASN and the CSN. R4 Communication protocol between ASN-GWs. R4 consists of a set of control and bearer plane protocols originating/terminating in various entities within the ASN that coordinate MS mobility between ASNs. In Release 1, R4 is the only interoperable interface between heterogeneous or dissimilar ASNs. R5 Consists of a set of control plane and bearer plane protocols for internetworking between CSNs operated by either the home or visited NSP. R6 Communication protocol between ASN-GW and BS R6 consists of a set of control and bearer plane protocols for communication between the BS and the ASN GW. The bearer plane consists of intra-ASN data path or inter-ASN tunnels between the BS and ASN-GW. The control plane includes protocols for IP tunnel management (establish, modify, and release) in accordance with the MS mobility events. R6 may also serve as a conduit for exchange of MAC states information between neighboring BSs. R8 Communication protocol between base stations. R8 consists of a set of control plane message flows and, in some situations, bearer plane data flows between the base stations to ensure fast and seamless handover. Bearer plane consists of protocols that allow the data transfer between Base Stations involved in handover of a certain MS. Control plane consists of the inter-BS communication protocol defined in IEEE 802.16 and additional set of protocols that allow controlling the data transfer between the Base Stations involved in handover of a certain MS. Session Session is a connection between one or more MS and a network element in order to exchange link-level frames or packets. SFID The service flow is identified using a SFID (Service Flow Identifier). Signaling Path A signaling path exists between the BS and ASN-GW, and is used for all signaling such as creating, dleteing, authenticating, as we as additional functions related to the subscriber. SR Session Redundancy Subscriber The 802.16 subscriber entity connects over the 802.16 airlink, and eventually results in the creation of the subscriber object at the ASN-GW. UHO Unpredicitive Handoff PMIP Proxy Mobile Internet Protocol HA Home Agent REFERENCE [1] WIMAX Forum Network Architecture, (Stage 3: Detailed Protocols and Procedures) Release 1.1.1 September 14, 2007.
Main OID:
ciscoAgwMIB.1.3.6.1.4.1.9.9.638
277
Objects
Active
Status
7
Dependencies

Imported Objects

Objects

277 total
Object Name
ciscoAgwMIB
MODULE-IDENTITY
.1.3.6.1.4.1.9.9.638
ciscoAgwMIBNotifs
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.638.0
ciscoAgwServiceDownNotif
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.638.0.1
ciscoAgwServiceUpNotif
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.638.0.2
ciscoAgwMaxBaseStationExceededOnsetNotif
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.638.0.3
ciscoAgwMaxBaseStationExceededAbateNotif
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.638.0.4
ciscoAgwMaxSubscribersExceededOnsetNotif
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.638.0.5
ciscoAgwMaxSubscribersExceededAbateNotif
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.638.0.6
ciscoAgwMIBObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.638.1
cagwInstances
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.638.1.1
cagwInstanceTable
SEQUENCE OF CagwInstanceEntry
.1.3.6.1.4.1.9.9.638.1.1.1
cagwInstanceEntry
CagwInstanceEntry
.1.3.6.1.4.1.9.9.638.1.1.1.1
cagwInstanceIndex
Unsigned32
.1.3.6.1.4.1.9.9.638.1.1.1.1.1
cagwInstancePhysicalIndexro
EntPhysicalIndexOrZero (CISCO-TC)
.1.3.6.1.4.1.9.9.638.1.1.1.1.2
cagwInstanceDescriptionro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.9.9.638.1.1.1.1.3
cagwInstanceVersionro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.9.9.638.1.1.1.1.4
cagwInstanceOperStatero
Enumeration
.1.3.6.1.4.1.9.9.638.1.1.1.1.5
cagwInstanceSessionRedundancyAdminro
Enumeration
.1.3.6.1.4.1.9.9.638.1.1.1.1.6
cagwState
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.638.1.2
cagwStateTable
SEQUENCE OF CagwStateEntry
.1.3.6.1.4.1.9.9.638.1.2.1
cagwStateEntry
CagwStateEntry
.1.3.6.1.4.1.9.9.638.1.2.1.1
cagwMaximumBaseStationsrw
Integer32 UNITS "base stations"
.1.3.6.1.4.1.9.9.638.1.2.1.1.1
cagwMaximumSubscribersrw
Integer32 UNITS "subscribers"
.1.3.6.1.4.1.9.9.638.1.2.1.1.2
cagwMaximumFlowsPerSessionrw
Integer32 UNITS "flows"
.1.3.6.1.4.1.9.9.638.1.2.1.1.3
cagwCurrentBaseStationsro
Gauge32 UNITS "paths"
.1.3.6.1.4.1.9.9.638.1.2.1.1.4
cagwCurrentDataPathsro
Gauge32 UNITS "paths"
.1.3.6.1.4.1.9.9.638.1.2.1.1.5
cagwCurrentSubscribersro
Gauge32 UNITS "subscribers"
.1.3.6.1.4.1.9.9.638.1.2.1.1.6
cagwCurrentSessionsro
Gauge32 UNITS "sessions"
.1.3.6.1.4.1.9.9.638.1.2.1.1.7
cagwCurrentFlowsro
Gauge32 UNITS "flows"
.1.3.6.1.4.1.9.9.638.1.2.1.1.8
cagwCurrentHostsro
Gauge32 UNITS "hosts"
.1.3.6.1.4.1.9.9.638.1.2.1.1.9
cagwNetworkBehindMsro
Gauge32 UNITS "mobile stations"
.1.3.6.1.4.1.9.9.638.1.2.1.1.10
cagwPendingSignalingPktsro
Gauge32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.2.1.1.11
cagwCurrentFramedRoutesro
Gauge32 UNITS "routes"
.1.3.6.1.4.1.9.9.638.1.2.1.1.12
cagwCurrentFramedRouteSubsro
Gauge32 UNITS "subscribers"
.1.3.6.1.4.1.9.9.638.1.2.1.1.13
cagwCurrentAutoProvSessionsro
Gauge32 UNITS "Sessions"
.1.3.6.1.4.1.9.9.638.1.2.1.1.14
cagwCurrentSessionsWithIpPktsRedirro
Gauge32 UNITS "Sessions"
.1.3.6.1.4.1.9.9.638.1.2.1.1.15
cagwCurrentPmipEnabledSubsro
Gauge32 UNITS "subscribers"
.1.3.6.1.4.1.9.9.638.1.2.1.1.16
cagwStatistics
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.638.1.3
cagwGlobalStatistics
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.638.1.3.1
cagwGlobalStatisticsTable
SEQUENCE OF CagwGlobalStatisticsEntry
.1.3.6.1.4.1.9.9.638.1.3.1.1
cagwGlobalStatisticsEntry
CagwGlobalStatisticsEntry
.1.3.6.1.4.1.9.9.638.1.3.1.1.1
cagwCreatedSubscribersro
Counter32 UNITS "subscribers"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.1
cagwDeletedSubscribersro
Counter32 UNITS "subscribers"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.2
cagwCreatedSessionsro
Counter32 UNITS "sessions"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.3
cagwDeletedSessionsro
Counter32 UNITS "sessions"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.4
cagwCreatedFlowsro
Counter32 UNITS "flows"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.5
cagwDeletedFlowsro
Counter32 UNITS "flows"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.6
cagwCreatedHostsro
Counter32 UNITS "hosts"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.7
cagwDeletedHostsro
Counter32 UNITS "hosts"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.8
cagwCreatedBaseStationsro
Counter32 UNITS "paths"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.9
cagwDeletedBaseStationsro
Counter32 UNITS "paths"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.10
cagwCreatedDataPathsro
Counter32 UNITS "paths"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.11
cagwDeletedDataPathsro
Counter32 UNITS "paths"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.12
cagwProcessedSignalingPktsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.13
cagwRequeuedSignalingPktsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.14
cagwCongestionSignalingPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.15
cagwServiceDisabledSignalingPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.16
cagwServiceNotReadySignalingPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.17
cagwEncapErrorSignalingPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.18
cagwDisposedSignalingPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.19
cagwEncapErrorDataPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.41
cagwInvalidAddressDataPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.42
cagwServiceDisabledDataPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.43
cagwInvalidProtocolTypeDataPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.44
cagwLengthErrorDataPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.45
cagwAbsentKeyDataPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.46
cagwFlowNotFoundDataPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.47
cagwFlowPathNotFoundDataPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.48
cagwFlowPathInvalidSourceDataPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.49
cagwSessionNotFoundDataPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.50
cagwSubscriberNotFoundDataPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.51
cagwChecksumErrorDataPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.52
cagwIngressFilteringDataPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.53
cagwSequenceNumberErrorDataPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.54
cagwFragmentedDataPktsDropsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.55
cagwFramedRouteInsertedroobsolete
Counter32 UNITS "routes"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.56
cagwFramedRouteInsertFailedroobsolete
Counter32 UNITS "routes"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.57
cagwFramedRouteDeletedroobsolete
Counter32 UNITS "routes"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.58
cagwServiceFlowProfileNotFoundro
Counter32 UNITS "service flow profiles"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.59
cagwQosProfileNotFoundro
Counter32 UNITS "qos profiles"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.60
cagwClassifierProfileNotFoundro
Counter32 UNITS "classifier profiles"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.61
cagwReceivedDataPktsrodeprecated
Counter64 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.62
cagwReceivedDataBytesrodeprecated
Counter64 UNITS "bytes"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.63
cagwSentDataPktsrodeprecated
Counter64 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.64
cagwSentDataBytesrodeprecated
Counter64 UNITS "bytes"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.65
cagwRejectedSessionsro
Counter32 UNITS "sessions"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.66
cagwRejectedFlowsro
Counter32 UNITS "flows"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.67
cagwRejectedBaseStationsro
Counter32 UNITS "paths"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.68
cagwSessionsDeletedByAgwro
Counter32 UNITS "sessions"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.69
cagwIpGreReceivedDataPktsro
Counter64 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.70
cagwIpGreReceivedDataBytesro
Counter64 UNITS "bytes"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.71
cagwIpGreSentDataPktsro
Counter64 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.72
cagwIpGreSentDataBytesro
Counter64 UNITS "bytes"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.73
cagwEthGreReceivedDataPktsro
Counter64 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.74
cagwEthGreReceivedDataBytesro
Counter64 UNITS "bytes"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.75
cagwEthGreSentDataPktsro
Counter64 UNITS "packets"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.76
cagwEthGreSentDataBytesro
Counter64 UNITS "bytes"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.77
cagwRejectedHostsro
Counter32 UNITS "hosts"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.78
cagwAgedOutStaticHostsro
Counter32 UNITS "hosts"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.79
cagwSuccessfulHandoffro
Counter32 UNITS "sessions"
.1.3.6.1.4.1.9.9.638.1.3.1.1.1.80
Showing 100 of 277 OID objects

CISCO-ASN-GATEWAY-MIB Technical Reference Overview

The CISCO-ASN-GATEWAY-MIB SNMP MIB module published by Cisco defines 277 managed OID objects, including 236 scalar/column metrics, 9 SNMP tables, and 6 trap/notification events anchored at base OID .1.3.6.1.4.1.9.9.638. Key tabular structures include cagwInstanceTable, cagwStateTable, cagwGlobalStatisticsTable, cagwDhcpStatisticsTable, cagwMsgTable, cagwUserGrpTable. Monitored SNMP traps/notifications include ciscoAgwServiceDownNotif, ciscoAgwServiceUpNotif, ciscoAgwMaxBaseStationExceededOnsetNotif, ciscoAgwMaxBaseStationExceededAbateNotif, ciscoAgwMaxSubscribersExceededOnsetNotif, ciscoAgwMaxSubscribersExceededAbateNotif.

Key OID Definitions in CISCO-ASN-GATEWAY-MIB

ciscoAgwMIBMODULE-IDENTITYnot-accessible
.1.3.6.1.4.1.9.9.638

This module manages Cisco's WiMAX ASN Gateway (ASN-GW). A WiMAX network supports wireless data communication through WiMAX radio (802.16) technology. The high level architecture of a first generation WiMAX network with the respective protocols for each interface is shown below: ++ | R2 | ++ ++ | | | R1 | | R6 | | | | MS || BS |-| ASN-GW | | | | | | | | ++ ++ | | | | | R3 |-| R8 | R4 | | | | | |-| ++ ++ | | | | R1 | | R6 | | | MS || BS |-| ASN-GW | | | | | | | | | ++ ++ R2 | | | ++ The diagram below depicts the relation of the subscriber to the session and flows: ++ -Flow (connected via data path) | ASN-GW | - Subscriber -Session -Flow (connected via data path) ++ | -Flow (connected via data path) | -Flow (connected via data path) | + A subscriber initiates a call from a MS. A session is created between the BS and the ASN-GW for that call. Multiple flows can be created for the session with different QOS parameters. For example one flow can created for a voice stream and another for data. Data paths are created between the BS and ASN-GW to forward the data packets of the created flows. When the first subscriber from any MS connected to a BS initiates a call via the BS to the ASN-GW, a signaling path is created between the BS and the ASN-GW. There is only one signaling path between each BS and ASN-GW. Signaling paths and base stations can be used interchangeably. The signaling and data paths remains active as long as there are subscribers connected to the ASN-GW from any MS connected to the BS. If a path has no session/flow connected, it will be purged after a certain period of time. This situation can occur when all subscribers on a certain path are disconnected. A subscriber disconnecting from a certain path does not indicate that the subscriber has left the network, it could simply be handing off to a different path. The IP addresses of the signaling and data paths can be the same or different both in the BS side and in the ASN-GW side. ++ ++ | Base | | ASN-GW | | Station| | | | | SigPath | | | IP(B1)|<............>|IP(A1) | | | | | | | | | | | DataPath 1 | | | IP(B2)|<............>|IP(A2) | | | | | | | DataPath 2 | | | IP(B3)|<............>|IP(A3) | ++ ++ Relationships: Base Station 1 to many Mobile Stations ASN-GW 1 to many Base Stations Subscriber 1 to 1 Sessions Session 1 to many Flows Datapath 1 to many Flows Signaling Path 1 to 1 Base Station Acronyms and terms: AAA AAA refers to a framework that specifies the protocols procedures for authentications, authorizatitin and accounting associated with the user, MS and subscribed serviced. AGW ASN-GW ASN ASN (Access Service network) is defined as a complete set of network functions needed to provide radio access to a WiMAX subscriber. ASN-GW ASN-Gateway is a logical entity that represents an aggregation of Control Plane functional entities that are either paired with a corresponding function in the ASN (for e.g BS instance) a resident function is the CSN or another functions in the ASN. For every MS, a BS is associated with exactly one default ASN-GW. However, ASN-GW functions for every MS may be distributes amongst multiple ASN-GWs located in one or more ASNs. The ASN-GW utilizes Session Redudancy to ensure a backup ASN-GW is available in case the primary ASN-GW goes down. BS Base Station is a logical entity that represents an aggregation of Control Plane functional entities that are either paired with a corresponding function in the ASN (e.g. BS instance), a resident function in the CSN or a function in another ASN. The ASN-GW may also perform Bearer Plane routing or bridging function. BSID The Base Station Identifier is a global unique identifier for a WiMAX base station. CPE Customer Premise Equipment. CSN CSN (Connectivity Service Network) is defined as a set of network functions that provide IP connectivity services to the WiMAX subscribers. Data Path Corresponding to each subscriber, data paths are created to foward packets between the ASN-GW and the subscribers. DPID Data Path ID is used to identify the tunnel carrying MS traffic between ASN gateways or between the ASN gateway and base station. As of 8/28/07, only the GRE key is to be used as the DPID. Flow A service flow is a unidirectional logical flow between the network and the Subscriber Station. A service flow is created to handle a different QoS over the connection oriented MAC. A subscriber can have multiple service flows associated and each service flow is associcated with an uplink and downlink classifier. GRE Generic Routing Encapsulation. Refer to RFC 1701 for more details. LB Load Balancing Messages Messages are packets exchanged on the signaling paths. MS The Mobile Station is a generalized mobile equipment set providing connectivity between subscriber equipment and a base station (BS) The Mobile Station may be a host or a CPE type of device that can support multiple hosts. MSID The Mobile Station Identifier is the 802.16 identifier used for all subscriber stations, and is used in all the messages over R6. The identifier associates all requests from a mobile to the ASN-GW. Packets Packets are datagrams fowarded over the data paths. R1 Communication protocol between mobile and BS as per the air interface (PHY and MAC) specifications (IEEE P802.16d/e). R1 may include additional protocols related to the management plane. R2 The interface between the MS and CSN associated with Authentication, Services Authorization, IP Host Configuration management, and mobility management. This is a logical interface thus does not reflect a direct protocol interface between MS and CSN. R3 The interface between the ASN and the CSN to support AAA, policy enforcement and mobility management capabilities. It also encompasses the bearer plane methods (e.g., tunneling) to transfer IP data between the ASN and the CSN. R4 Communication protocol between ASN-GWs. R4 consists of a set of control and bearer plane protocols originating/terminating in various entities within the ASN that coordinate MS mobility between ASNs. In Release 1, R4 is the only interoperable interface between heterogeneous or dissimilar ASNs. R5 Consists of a set of control plane and bearer plane protocols for internetworking between CSNs operated by either the home or visited NSP. R6 Communication protocol between ASN-GW and BS R6 consists of a set of control and bearer plane protocols for communication between the BS and the ASN GW. The bearer plane consists of intra-ASN data path or inter-ASN tunnels between the BS and ASN-GW. The control plane includes protocols for IP tunnel management (establish, modify, and release) in accordance with the MS mobility events. R6 may also serve as a conduit for exchange of MAC states information between neighboring BSs. R8 Communication protocol between base stations. R8 consists of a set of control plane message flows and, in some situations, bearer plane data flows between the base stations to ensure fast and seamless handover. Bearer plane consists of protocols that allow the data transfer between Base Stations involved in handover of a certain MS. Control plane consists of the inter-BS communication protocol defined in IEEE 802.16 and additional set of protocols that allow controlling the data transfer between the Base Stations involved in handover of a certain MS. Session Session is a connection between one or more MS and a network element in order to exchange link-level frames or packets. SFID The service flow is identified using a SFID (Service Flow Identifier). Signaling Path A signaling path exists between the BS and ASN-GW, and is used for all signaling such as creating, dleteing, authenticating, as we as additional functions related to the subscriber. SR Session Redundancy Subscriber The 802.16 subscriber entity connects over the 802.16 airlink, and eventually results in the creation of the subscriber object at the ASN-GW. UHO Unpredicitive Handoff PMIP Proxy Mobile Internet Protocol HA Home Agent REFERENCE [1] WIMAX Forum Network Architecture, (Stage 3: Detailed Protocols and Procedures) Release 1.1.1 September 14, 2007.

cagwInstanceTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.638.1.1.1

The ASN-GW Instance Table contains an entry for each physical ASN Gateway.

cagwStateTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.638.1.2.1

The State Table contains Statistics about the current state of the ASN-GW.

cagwGlobalStatisticsTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.638.1.3.1.1

The Global Statistics Table contains measurement for a particular ASN-Gateway.

cagwDhcpStatisticsTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.638.1.3.2.1

The DHCP Statistics Table contains Statistics about DHCP packets processed by the ASN-GW.

cagwMsgTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.638.1.3.3.1

The Message Table contains Statistics about all message types in the R6 protocol.

cagwUserGrpTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.638.1.3.4.1

The User Group table includes information and statistics about each user group.

cagwPathTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.638.1.3.5.1

The Path table includes information and statistics about each base station.

cagwPathRev1TableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.638.1.3.5.2

The Path table includes information and statistics about each base station.

cagwArpStatisticsTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.638.1.3.6.1

The ARP Statistics Table contains Statistics about ARP requests handled by the ASN-GW.

ciscoAgwServiceDownNotifNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.638.0.1

A notification of this type is generated when the ASN-GW is not in service.

ciscoAgwServiceUpNotifNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.638.0.2

A notification of this type is generated when the ASN-GW is in service.

ciscoAgwMaxBaseStationExceededOnsetNotifNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.638.0.3

A notification of this type is generated when the number of base stations exceeded the percent of the maximum number of base stations as specified by the object cagwMaxBaseStationExceededNotifThreshold.

ciscoAgwMaxBaseStationExceededAbateNotifNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.638.0.4

A notification of this type is generated when the number of base stations goes below the percent of the maximum number of base stations as specified by the object cagwMaxBaseStationExceededNotifThreshold.

ciscoAgwMaxSubscribersExceededOnsetNotifNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.638.0.5

A notification of this type is generated when the number of subscribers exceeded the percent of the maximum number of base stations as specified by the object cagwMaxSubscribersExceededNotifThreshold.

ciscoAgwMaxSubscribersExceededAbateNotifNOTIFICATION-TYPEnot-accessible
.1.3.6.1.4.1.9.9.638.0.6

A notification of this type is generated when the number of subscribers goes below the percent of the maximum number of base stations as specified by the object cagwMaxSubscribersExceededNotifThreshold.

cagwNotifEnabledTruthValueread-write
.1.3.6.1.4.1.9.9.638.1.4.1

Indicates whether notifications are generated by the device. - When set to 'true' it will enable all the traps - When set to 'false' it will disable all the traps This object will remain 'true' as long as any trap is enabled.

cagwNotifSeverityLevelCiscoAlarmSeverityread-write
.1.3.6.1.4.1.9.9.638.1.4.2

This object is used to indicate which severity of notifications are generated by the device. The following is a list of severities from highest to lowest and these value are defined in the CiscoAlarmSeverity textual convention from CISCO-TC. critical(3) - highest severity major(4) minor(5) warning(6) info(7) - lowest severity All notification with a severity higher or equal to the this object will be generated. This object cannot be set to cleared(1) or indeterminate(2).

cagwRepeatNotifIntervalInteger32read-write
.1.3.6.1.4.1.9.9.638.1.4.3

The purpose of this object is to define the length of interval used to prevent the excessive generations of notifications. Notification related to the same event(alarm) will be suppressed for the duration of the interval. Notifications for the same entity(object with same indexes) will be suppressed for length of interval. For example, the ciscoAgwMaxBaseStationExceededOnsetNotif and ciscoAgwMaxBaseStationExceededAbateNotif notification are used to indicate the event were the number of basestations that can be supported has been reached and requests from additional base stations will be reject. Here is an example of how the suppression mechanism works: cagwMaxBaseStationExceededNotifThreshold = 90% cagwMaximumBaseStations = 1000 threshold = 900 Time 9:00:00 cagwCurrentBaseStations = 901 device sends ciscoAgwMaxBaseStationExceededOnsetNotif Time 9:00:04 cagwCurrentBaseStations = 899 device does not send ciscoAgwMaxBaseStationExceededAbateNotif Time 9:00:07 cagwCurrentBaseStations = 901 device does not send ciscoAgwMaxBaseStationExceededOnsetNotif Time 9:00:11 cagwCurrentBaseStations = 899 device does not send ciscoAgwMaxBaseStationExceededAbateNotif . . Time 9:05:00 Interval Ends and cagwCurrentBaseStations = 822 device sends ciscoAgwMaxBaseStationExceededAbateNotif When this object is set to zero notification will not be suppressed.

cagwGeneratedNotifsCounter32read-only
.1.3.6.1.4.1.9.9.638.1.4.4

The number of notifications that have been generated for this management information base.

cagwIgnoredNotifsCounter32read-only
.1.3.6.1.4.1.9.9.638.1.4.5

The number of notification that were not sent because the notifications specified severity was lower than the minimum defined by cagwNotifSeverityLevel object or because the notification supression mechanism described in cagwRepeatNotifInterval blocked the notification.

cagwServiceNotifEnabledTruthValueread-write
.1.3.6.1.4.1.9.9.638.1.4.11

Indicates whether ciscoAgwServiceDownNotif and ciscoAgwServiceUpNotif notifications will be generated by the device as follows. 'true' - Notification generation is enabled. 'false' - Notification generation is disabled.

cagwServiceNotifSeverityCiscoAlarmSeverityread-write
.1.3.6.1.4.1.9.9.638.1.4.12

Indicates the severity of the ciscoAgwServiceDownNotif notification. The severity of ciscoAgwServiceUpNotif is 'cleared'. This object cannot be set to cleared(1) or indeterminate(2).

cagwGeneratedServiceNotifsCounter32read-only
.1.3.6.1.4.1.9.9.638.1.4.13

The number of ciscoAgwServiceDownNotif notifications that have been generated. Discontinuites in the value of this counter can occur at re-initialization of the management system or reloading of the device.

More MIBs from Cisco

Browse all CiscoMIBs →
CISCO-UNIFIED-COMPUTING-COMPUTE-MIB

The CISCO-UNIFIED-COMPUTING-COMPUTE-MIB provides SNMP-based monitoring and management of Cisco UCS compute blades, servers, and chassis components, exposing critical metrics such as CPU utilization, memory usage, thermal sensor readings, power supply status, and interface operational states. This module enables granular visibility into the health and performance of the Cisco Unified Computing System's compute subsystems for capacity planning and fault isolation.

1401 objects→
CISCO-UNIFIED-COMPUTING-STORAGE-MIB

The CISCO-UNIFIED-COMPUTING-STORAGE-MIB facilitates SNMP-based monitoring and management of storage subsystems, including Fibre Channel and iSCSI interfaces, within the Cisco Unified Computing System (UCS) fabric interconnects and blade servers. It exposes critical operational metrics such as port status, error counters, throughput statistics, and storage controller health states to enable granular visibility into the storage infrastructure.

1295 objects→
CISCO-UNIFIED-COMPUTING-VNIC-MIB

The CISCO-UNIFIED-COMPUTING-VNIC-MIB enables SNMP-based monitoring and management of Virtual Network Interface Card (vNIC) attributes, including operational status, traffic counters, and binding configurations, within the Cisco Unified Computing System (UCS) fabric interconnects and server blades.

1161 objects→
CERENT-GENERIC-MIB

SNMP MIB module

984 objects→
CISCO-UNIFIED-COMPUTING-BIOS-MIB

The CISCO-UNIFIED-COMPUTING-BIOS-MIB enables SNMP-based monitoring and configuration of BIOS-level parameters, firmware versions, and hardware initialization states within Cisco Unified Computing System (UCS) servers. It provides visibility into critical server boot diagnostics, BIOS settings, and hardware readiness indicators to facilitate low-level infrastructure management and troubleshooting.

937 objects→
CISCO-UNIFIED-COMPUTING-ETHER-MIB

The CISCO-UNIFIED-COMPUTING-ETHER-MIB provides SNMP management interfaces for monitoring Ethernet interface statistics, link states, and error counters on Cisco Unified Computing System (UCS) fabric interconnects and blade server line cards. This module enables the tracking of physical layer connectivity, port throughput, and packet error rates within the UCS Ethernet switching infrastructure.

920 objects→