CISCO-6400-CHASSIS-MIB
AI MIB Summary
The CISCO-6400-CHASSIS-MIB monitors the redundancy state and health of the Network Redundancy Protocol (NRP) on Cisco 6400 series chassis, specifically tracking switchover events, secondary unit failures, removals, and configuration mismatches. It provides critical alarm notifications for NRP synchronization integrity to ensure high availability of the chassis control plane.
Add nrpSwitchoverAlarm, nrpSecondaryFailureAlarm, nrpSecondaryRemovedAlarm, and nrpMismatchAlarm.
Main OID:
cisco6400ChassisMIB.1.3.6.1.4.1.9.10.27
88
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
88 total| Object Name |
|---|
cisco6400ChassisMIBAdd nrpSwitchoverAlarm,
nrpSecondaryFailureAlarm,
nrpSecondaryRemovedAlarm, and
nrpMismatchAlarm. MODULE-IDENTITY .1.3.6.1.4.1.9.10.27 |
cisco6400ChassisMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.27.1 |
c64RedundantGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.27.1.1 |
c64MainCPUConfigAutoSyncThis object is an OR bit mask indicating various
auto-sync configuration:
Bit 0, if set, indicates that standard syncable
objects are set for auto-sync. The standard
set of objects may evolve from software release
to release. In release 1, this set is
startup-config, bootvar and config-register.
This flag is independent to the other flag
settings described below.
Bit 1, if set, indicates startup-config is set for
auto-sync
Bit 2. if set, indicates running-config is set for
auto-sync. This flag is not supported in
revison 1.
Bit 3, if set, indicates bootvar is set for auto-sync
Bit 4, if set, indicates config-register is set for
auto-sync.
Bit 5..31, are reserved for future expansion. Setting
any bit in this range will have no effect.rw Integer32 .1.3.6.1.4.1.9.10.27.1.1.1 |
c64MainCPUSwitchOverThis object, when read always return a value of
ok(1).
Setting this object to forceOver(2) will have:
For a redundant NSP-A|B, force them to exchange the
primary and secondary roles. The primary NSP will
be reloaded.rw Enumeration .1.3.6.1.4.1.9.10.27.1.1.2 |
c64SlotConfigTableA list of redundant slot-pair entries.
A managment station that wish to create the redundancy
entry other than NSP should perform the following
steps:
Get the ciscoLS1010ModuleIndex from
ciscoLS1010ModuleTable which are mapped to the
corresponding pair of the physical slots to be
configured for redundancy.
Use the pair of the ciscoLS1010ModuleIndex
and a unique entry index to create table entry.
Only the adjacent slots can be configured for
redundancy. SEQUENCE OF C64SlotConfigEntry .1.3.6.1.4.1.9.10.27.1.1.3 |
c64SlotConfigEntryEntry containing information for a particular pair
of redundant slots. The object value of
c64Slot1Index & c64Slot2Index refer to
the pair of ciscoLS1010ModuleIndex in
ciscoLS1010ModuleTable to be configured as redundant. C64SlotConfigEntry .1.3.6.1.4.1.9.10.27.1.1.3.1 |
c64SlotConfigModule1IndexThis object specify the first slot in the pair of
slots to be configured for the redundacy. Its value
is obtained from ciscoLS1010ModuleIndex in
ciscoLS1010ModuleTable. INTEGER .1.3.6.1.4.1.9.10.27.1.1.3.1.1 |
c64SlotConfigModule2IndexThis object specify the second slot in the pair of
slots to be configured for the redundacy. Its value
is the obtained from ciscoLS1010ModuleIndex in
ciscoLS1010ModuleTable. INTEGER .1.3.6.1.4.1.9.10.27.1.1.3.1.2 |
c64Slot1NameName of slot#1 in the pair of slots
configured to redundant.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.10.27.1.1.3.1.3 |
c64Slot2NameName of slot#2 in the pair of slots
configured to redundant.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.10.27.1.1.3.1.4 |
c64SlotConfigPrefIndexThis object specify which slot in the pair
of redundancy to be used as prefer slot.
The value of:
primarySlot(1) is telling the system use the slot
referred by c64Slot1Index as preferred slot.
secondarySlot(2) is to use the slot referred by
c64Slot2Index.
The default is primarySlot(1).
The slot prefer feature is removed and the
the object is deprecatedrwdeprecated Enumeration .1.3.6.1.4.1.9.10.27.1.1.3.1.5 |
c64SlotSwitchOverThis object, when read always return a value of
ok(1).
Setting this object to forceOver(2) will have:
For a redundant NRP slot pair, force them
to exchange the primary and secondary roles.
For a redundant carrier slot pair, force both
the subslots (line cards) to exchange the
primary(working) and secondary(protection) roles.rw Enumeration .1.3.6.1.4.1.9.10.27.1.1.3.1.6 |
c64SlotConfigStatusThe status object for the c64SlotTable entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.10.27.1.1.3.1.7 |
c64SubSlotConfigTableA list of redundant subslot pair entries.
A managment station that wish to create the
subslot redundancy entry should perform the
following steps:
Get the ciscoLS1010ModuleIndex &
ciscoLS1010SubModuleIndex from
ciscoLS1010SubModuleTable which are mapped to the
corresponding pair of the physical sub-slots to be
configured for the redundancy.
Use the pair of the ciscoLS1010ModuleIndex &
ciscoLS1010SubModuleIndex and an unique entry index
to create table entry. Only the adjacent sub-slots
can be configured for redundancy. SEQUENCE OF C64SubSlotConfigEntry .1.3.6.1.4.1.9.10.27.1.1.5 |
c64SubSlotConfigEntryEntry containing information for a particular pair
of redundant subslots. C64SubSlotConfigEntry .1.3.6.1.4.1.9.10.27.1.1.5.1 |
c64SubSlotRedundantIndexAn arbitrary integer-value to uniquely identify
a redundant slot pair. This value must remain
constant while the NSP is running. It is not
guarenteed to be constant between reboots or
switchover of the NSP. INTEGER .1.3.6.1.4.1.9.10.27.1.1.5.1.1 |
c64SubSlotConfigModule1IndexThis object specify the first slot in the pair of
sub-slots to be configured for the redundancy. Its
value is obtained from the ciscoLS1010ModuleIndex in
ciscoLS1010SubModuleTable. INTEGER .1.3.6.1.4.1.9.10.27.1.1.5.1.2 |
c64SubSlotConfigSubModule1IndexThis object specify the first sub-slot in the pair
of sub-slots to be configured for the redundancy. Its
value is obtained from the ciscoLS1010SubModuleIndex
in ciscoLS1010SubModuleTable. INTEGER .1.3.6.1.4.1.9.10.27.1.1.5.1.3 |
c64SubSlotConfigModule2IndexThis object specify the second slot in the pair of
sub-slots to be configured for the redundancy. Its
value is obtained from the ciscoLS1010ModuleIndex
in ciscoLS1010SubModuleTable. INTEGER .1.3.6.1.4.1.9.10.27.1.1.5.1.4 |
c64SubSlotConfigSubModule2IndexThis object specify the second sub-slot in the pair
of sub-slots to be configured for the redundancy. Its
value is obtained from the ciscoLS1010SubModuleIndex
in ciscoLS1010SubModuleTable. INTEGER .1.3.6.1.4.1.9.10.27.1.1.5.1.5 |
c64SubSlot1NameThis object is to reflect the string name in the
format of #/# for the sub-slot1 in the pair of
redundancy. This is produced by agent when
the table entry is created.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.10.27.1.1.5.1.6 |
c64SubSlot2NameThis object is to reflect the string name in the
format of #/# for the sub-slot2 in the pair of
redundancy. This is produced by agent when table
entry is created.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.10.27.1.1.5.1.7 |
c64SubSlotConfigPrefIndexThis object specify which sub-slot in the pair of
redundancy to be used as prefer sub-slot.
The value of:
primarySubslot(1) is telling the system use the subslot
referred by c64SubSlotConfigModule1Index
and c64SubSlotConfigSubModule1Index as
preferred sub-slot.
secondarySubslot(2) is to use the sub-slot referred by
c64SubSlotConfigModule2Index and
c64SubSlotConfigSubModule2Index.
The default is primarySubslot(1).
The subslot prefer feature is removed and the object
is deprecatedrwdeprecated Enumeration .1.3.6.1.4.1.9.10.27.1.1.5.1.8 |
c64SubSlotSwitchOverThis object, when read always return a value of
ok(1). Setting this object to forceOver(2)
will have the result of:
For a redundant subslot card pair, force the
current master and slave cards (for NRPs) or
working and protection cards (for linecards) to
exchange roles.rw Enumeration .1.3.6.1.4.1.9.10.27.1.1.5.1.9 |
c64SubSlotConfigStatusThe status object for c64SubSlotConfigTable
entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.10.27.1.1.5.1.10 |
c64PortConfigTableA list of redundant port-pair entries.
A management station that wish to create the
redundant entry should perform the following
steps:
Get the ciscoLS1010ModuleIndex,
ciscoLS1010SubModuleIndex and
ciscoLS1010PortIndex
from ciscoLS1010PortTable which are mapped to
the corresponding pair of the physical ports to
be configured for the redundancy.
Lookup the c64SubSlotConfigTable to see if
the corresponding sub-slots has been configured
for redundancy. If yes, get the entry's
c64SubSlotRedundantIndex. Otherwise the
application should abort this port redundancy
configuration.
Use the c64SubSlotRedundantIndex value and
ciscoLS1010ModuleIndex, ciscoLS1010SubModuleIndex and
ciscoLS1010PortIndex to create table entry. Only
the adjacent ports in the adjacent sub-slots can
be configured for redundancy. SEQUENCE OF C64PortConfigEntry .1.3.6.1.4.1.9.10.27.1.1.6 |
c64PortConfigEntryEntry containing information for a particual pair of
redundant ports. C64PortConfigEntry .1.3.6.1.4.1.9.10.27.1.1.6.1 |
c64PortConfigModule1IndexThis object specify the first slot which contain
the port to be configured as the redundancy pair.
Its value is obtained from the ciscoLS1010ModuleIndex
in ciscoLS1010PortTable. INTEGER .1.3.6.1.4.1.9.10.27.1.1.6.1.1 |
c64PortConfigSubModule1IndexThis object specify the first sub-slot which contain
the port to be configured as the redundancy pair.
Its value is obtained from ciscoLS1010SubModuleIndex
in ciscoLS1010PortTable. INTEGER .1.3.6.1.4.1.9.10.27.1.1.6.1.2 |
c64PortConfigPort1IndexThis object specify the first port in the pair of
ports to be configured for the redundancy.
Its value is obtained from ciscoLS1010PortIndex in
ciscoLS1010PortTable. INTEGER .1.3.6.1.4.1.9.10.27.1.1.6.1.3 |
c64PortConfigModule2IndexThis object specify the second slot which contain
the port to be configured as the redundancy pair.
Its value is obtained from the ciscoLS1010ModuleIndex
in ciscoLS1010PortTable. INTEGER .1.3.6.1.4.1.9.10.27.1.1.6.1.4 |
c64PortConfigSubModule2IndexThis object specify the second sub-slot which contain
the port to be configured as the redundancy pair.
Its value is obtained from the
ciscoLS1010SubModuleIndex in ciscoLS1010PortTable. INTEGER .1.3.6.1.4.1.9.10.27.1.1.6.1.5 |
c64PortConfigPort2IndexThis object specify the second port in the pair of
ports to be configured for the redundancy.
Its value is obtained from the ciscoLS1010PortIndex in
ciscoLS1010PortTable. INTEGER .1.3.6.1.4.1.9.10.27.1.1.6.1.6 |
c64Port1NameThis object is to reflect the string name in the
format of #/#/# for the port1 in the pair of
redundancy. This is produced by agent when the
table entry is created.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.10.27.1.1.6.1.7 |
c64Port2NameThis object is to reflect the string name in the
format of #/#/# for the port2 in the pair of
redundancy. This is produced by agent when the
table entry is created.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.10.27.1.1.6.1.8 |
c64PortConfigPrefIndexThis object specify which port in the pair of
redundancy to be used as prefer port.
The value of:
primaryPort(1) is telling the system use the port
referred by c64PortConfigModule1Index,
c64PortConfigSubModule1Index and
c64PortConfigPort1Index as preferred port.
secondaryPort(2) is to use the port referred by
c64PortConfigModule2Index,
c64PortConfigSubModule2Index and
c64PortConfigPort2Index.
The default is primaryPort(1).rw Enumeration .1.3.6.1.4.1.9.10.27.1.1.6.1.9 |
c64PortSwitchOverThis object, when read always return a value of
ok(1). Setting this object to one of the acceptable
values gives the following results:
forceOver(2): Force the current working and
protection ports to exchange roles.rw Enumeration .1.3.6.1.4.1.9.10.27.1.1.6.1.10 |
c64PortConfigStatusThe status object for c64PortConfigTable
entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.10.27.1.1.6.1.11 |
c64SonetAPSConfigTableA table containing all instances of Sonet APS
configuration informations. To configure any APS
objects in this table, the corresponding subslots
pair have to be already configured for redundancy. SEQUENCE OF C64SonetAPSConfigEntry .1.3.6.1.4.1.9.10.27.1.1.7 |
c64SonetAPSConfigEntryEntry containing APS information for a particular
interface. C64SonetAPSConfigEntry .1.3.6.1.4.1.9.10.27.1.1.7.1 |
c64SonetAPSModeThis object is used to set the APS mode on the
corresponding interface referenced by ifIndex object.
The value linear(1) is the APS mode of linear 1+1
nonreverting and unidirectional. This only
true APS mode supported in cisco6400 at FCS.
The value yCable(2) is providing the port hardware
redundancy but not transmission line redundancy and
is not strictly an APS mode.rw Enumeration .1.3.6.1.4.1.9.10.27.1.1.7.1.1 |
c64SonetAPSBERThresholdThis is object is used to set the Bit-Error-Rate
threshold at which an APS request of priority
'Signal Degrade' will be posted.
Value of 0 to disable the threshold.rw INTEGER .1.3.6.1.4.1.9.10.27.1.1.7.1.2 |
c64SonetAPSSwitchCmdThis object when set except clear(4) is used to post
an APS priority request. This request succeeds if no
higher-priority request is posted.
lockOut(1):
locks out the protection channel corresponding
to this entry
forceWorking(2) & manualWorking(4):
post a request to switch away from the
working channel to protection channel of
this entry
forceProtect(3) & manualProtect(5):
post a request to switch away from the
protection channel to working channel of
this entry
clear(6):
Clears all posted APS priority requests in
this channel.rw Enumeration .1.3.6.1.4.1.9.10.27.1.1.7.1.3 |
c64SonetAPSSFBERThresholdThis is object is used to set the Signal Fail
Bit-Error-Rate threshold at which an APS
request of priority 'Signal Fail' will be posted.
3 => 10E-3, 4 => 10E-4, 5 => 10E-5rw INTEGER .1.3.6.1.4.1.9.10.27.1.1.7.1.4 |
c64SonetAPSStatsTableA table containing APS statistics and alarms
information for each interface. SEQUENCE OF C64SonetAPSStatsEntry .1.3.6.1.4.1.9.10.27.1.1.8 |
c64SonetAPSStatsEntryA row in the c64SonetAPSStatsTable which corresponds
to the statistics/alarms kept by a particular
APS interface. C64SonetAPSStatsEntry .1.3.6.1.4.1.9.10.27.1.1.8.1 |
c64SonetAPSWorkSectionStatusThis variable indicates the section level status of
the working channel in APS. The
c64SonetAPSWorkSectionStatus is a bit map represented
as a sum of multiple alarms simultaneously. The
sonetSectionNoDefect should be set if and only if no
other flag is set.
The various bit position are:
1 sonetSectionNoDefect
2 sonetSectionLOS
3 sonetSectionLOF
4 sonetBIPE(BIp-8)ro Integer32 .1.3.6.1.4.1.9.10.27.1.1.8.1.1 |
c64SonetAPSWorkLineStatusThis variable indicates the line level status of the
working channel in APS. The
c64SonetAPSWorkLineStatus is a bit map represented as
a sum of multiple alarms simultaneously. The
sonetLineNoDefect should be set if and only if no
other flag is set.
The various bit position are:
1 sonetLineNoDefect
2 sonetLineAIS
3 sonetLineRDI
4 sonetBIPE(BIP-8/24)
5 sonetFEBEro Integer32 .1.3.6.1.4.1.9.10.27.1.1.8.1.2 |
c64SonetAPSWorkPathStatusThis variable indicates the path level status of the
working channel in APS. The
c64SonetAPSWorkPathStatus is a bit map represented as
a sum of multiple alarms simultaneously. The
sonetPathNoDefect should be set if and only if no
other flag is set.
The various bit position are:
1 sonetPathNoDefect
2 sonetPathSTSAIS
3 sonetPathSTSRDI
4 sonetPathSTSLOP
5 sonetBIPE(BIP-8)
6 sonetFEBE
7 sonetPathUnequipped
8 sonetPathSignalLabelMismatchro Integer32 .1.3.6.1.4.1.9.10.27.1.1.8.1.3 |
c64SonetAPSWorkSectionBIPEThis object counts the number of section BIP-8 errors
in working channel.ro Counter32 .1.3.6.1.4.1.9.10.27.1.1.8.1.4 |
c64SonetAPSWorkLineBIPEThis object counts the number of line BIP-8/24 errors
in working channel.ro Counter32 .1.3.6.1.4.1.9.10.27.1.1.8.1.5 |
c64SonetAPSWorkLineFEBEThis object counts the number of line
far-end-block-errors in working channel.ro Counter32 .1.3.6.1.4.1.9.10.27.1.1.8.1.6 |
c64SonetAPSWorkPathBIPEThis object counts the number of path BIP-8 errors
in working channel.ro Counter32 .1.3.6.1.4.1.9.10.27.1.1.8.1.7 |
c64SonetAPSWorkPathFEBEThis object counts the number of path
far-end-block-errors in working channel.ro Counter32 .1.3.6.1.4.1.9.10.27.1.1.8.1.8 |
c64SonetAPSWorkPortStatusThis object indicates the last aps event detected
in working port.ro APSEventStatus .1.3.6.1.4.1.9.10.27.1.1.8.1.9 |
c64SonetAPSProtectSectionStatusThis variable indicates the section level status of
the protection channel in APS. The
c64SonetAPSProtectSectionStatus is a bit map
represented as a sum of multiple alarms simultaneously.
The sonetSectionNoDefect should be set if and only if
no other flag is set.
The various bit position are:
1 sonetSectionNoDefect
2 sonetSectionLOS
4 sonetSectionLOF
8 sonetBIPE(BIp-8)ro Integer32 .1.3.6.1.4.1.9.10.27.1.1.8.1.10 |
c64SonetAPSProtectLineStatusThis variable indicates the line level status of the
protection channel in APS. The
c64SonetAPSProtectLineStatus is a bit map represented
as a sum of multiple alarms simultaneously. The
sonetLineNoDefect should be set if and only if no
other flag is set.
The various bit position are:
1 sonetLineNoDefect
2 sonetLineAIS
4 sonetLineRDI
8 sonetBIPE(BIP-8/24)
16 sonetFEBEro Integer32 .1.3.6.1.4.1.9.10.27.1.1.8.1.11 |
c64SonetAPSProtectPathStatusThis variable indicates the path level status of the
protection channel in APS. The
c64SonetAPSProtectPathStatus is a bit map represented
as a sum of multiple alarms simultaneously. The
sonetPathNoDefect should be set if and only if no
other flag is set.
The various bit position are:
1 sonetPathNoDefect
2 sonetPathSTSLOP
4 sonetPathSTSAIS
8 sonetBIPE(BIP-8)
16 sonetFEBE
32 sonetPathSTSRDI
64 sonetPathUnequipped
128 sonetPathSignalLabelMismatchro Integer32 .1.3.6.1.4.1.9.10.27.1.1.8.1.12 |
c64SonetAPSProtectSectionBIPEThis object counts the number of section BIP-8 errors
in protection channel.ro Counter32 .1.3.6.1.4.1.9.10.27.1.1.8.1.13 |
c64SonetAPSProtectLineBIPEThis object counts the number of line BIP-8/24 errors
in protection channel.ro Counter32 .1.3.6.1.4.1.9.10.27.1.1.8.1.14 |
c64SonetAPSProtectLineFEBEThis object counts the number of line
far-end-block-errors in protection channel.ro Counter32 .1.3.6.1.4.1.9.10.27.1.1.8.1.15 |
c64SonetAPSProtectPathBIPEThis object counts the number of path BIP-8 errors
in protection channel.ro Counter32 .1.3.6.1.4.1.9.10.27.1.1.8.1.16 |
c64SonetAPSProtectPathFEBEThis object counts the number of path
far-end-block-errors in protection channel.ro Counter32 .1.3.6.1.4.1.9.10.27.1.1.8.1.17 |
c64SonetAPSProtectPortStatusThis object indicates the last aps event detected
in protection port.ro APSEventStatus .1.3.6.1.4.1.9.10.27.1.1.8.1.18 |
c64SonetAPSChannelStatusThis object indicates the last aps event detected in
the APS channel.ro APSEventStatus .1.3.6.1.4.1.9.10.27.1.1.8.1.19 |
c64ChassisGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.27.1.2 |
c64TelcoAlarmMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.27.1.2.1 |
c64ChassisFacilityAlarmStatusThis object is an OR bit mask indicating the
presence of critical/major/minor telco alarm:
Bit 0, if set, indicates the presence of minor alarm
Bit 1, if set, indicates the presence of major alarm
Bit 2, if set, indicates the presence of critical alarmro Integer32 .1.3.6.1.4.1.9.10.27.1.2.1.1 |
c64ChassisClearAlarmsThis object is used to clear all, major or minor alarms
indication and reset the alarm contacts. When the
clear command is done the value of this object will
be set to done(0).rw Enumeration .1.3.6.1.4.1.9.10.27.1.2.1.2 |
c64ChassisTempIntakeMinorThresholdThis object is used to set the intake minor
temperature alarm threshold in degrees centigrade.
The default value is ???.rw INTEGER .1.3.6.1.4.1.9.10.27.1.2.1.3 |
c64ChassisTempIntakeMajorThresholdThis object is used to set the intake major
temperature alarm threshold in degrees centigrade.
The default value is ???.rw INTEGER .1.3.6.1.4.1.9.10.27.1.2.1.4 |
c64ChassisTempCoreMinorThresholdThis object is used to set the core minor
temperature alarm threshold in degrees centigrade.
The default value is ???.rw INTEGER .1.3.6.1.4.1.9.10.27.1.2.1.5 |
c64ChassisTempCoreMajorThresholdThis object is used to set the core major
temperature alarm threshold in degrees centigrade.
The default value is ???.rw INTEGER .1.3.6.1.4.1.9.10.27.1.2.1.6 |
c64ChassisTempThresholdAdminThis object is used to enable/disable various
threshold limit.
Bit 0, if set to 0 disable the intake minor threshold
otherwise enable it.
Bit 1, if set to 0 disable the intake major threshold
otherwise enable it.
Bit 2, if set to 0 disable the core minor threshold
otherwise enable it.
Bit 3, if set to 0 disable the core major threshold
otherwise enable it.rw Integer32 .1.3.6.1.4.1.9.10.27.1.2.1.7 |
c64ChassisAlarmTableThe table contains the current alarm status in the
system. SEQUENCE OF C64ChassisAlarmEntry .1.3.6.1.4.1.9.10.27.1.2.2 |
c64ChassisAlarmEntryEntry containing alarm information occurred in the
system. C64ChassisAlarmEntry .1.3.6.1.4.1.9.10.27.1.2.2.1 |
c64ChassisAlarmIndexAn arbitrary integer value to uniquely identify
a alarm information entry.ro INTEGER .1.3.6.1.4.1.9.10.27.1.2.2.1.1 |
c64ChassisAlarmSourceThis object indicates the source of alarm. The
variable will contain string in the following formats:
'Chassis' indicate the chassis alarms
'Submodule' indicate the submodule alarms
'port@slot#/subslot#/port#'
indicate the port alarms.
NMS app. will need to recognize the above three format
in order to tell the alarm sources. The value other
than the above three format cannot be allowed.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.10.27.1.2.2.1.2 |
c64ChassisAlarmTypeThis object indicates the type of alarm.ro Enumeration .1.3.6.1.4.1.9.10.27.1.2.2.1.3 |
c64ChassisAlarmSeverityThis object indicates the severity of the alarm.ro Enumeration .1.3.6.1.4.1.9.10.27.1.2.2.1.4 |
c64ChassisAlarmACOStatusThis object indicates whether the audible/visible
local alarm relay has been locally cut off for this
particular alarm source. When this status is 'normal',
the alarm in this entry has closed the local
audible/visible alarm relay contacts. When this
status is 'cutoff', the alarm in this entry initially
closed the local relay contacts, but was suppressed by
a local user pressing the external ACO button on the
6400 NSP.ro Enumeration .1.3.6.1.4.1.9.10.27.1.2.2.1.5 |
cisco6400ChassisMIBNotificationPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.27.2 |
cisco6400ChassisMIBNotification OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.27.2.0 |
cisco6400ChassisFailureNotificationThe notification signifies that the agent detects a change in
the c64ChassisAlarmTable, the NMS application should start
to poll the c64ChassisAlarmTable to get up-to-date alarm
information. NOTIFICATION-TYPE .1.3.6.1.4.1.9.10.27.2.0.1 |
cisco6400ChassisMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.27.3 |
cisco6400ChassisMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.27.3.1 |
cisco6400ChassisMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.27.3.2 |