CIE1000-LLDP-MIB
This is a private version of the LLDP MIB
Main OID:
cie1000LldpMib.1.3.6.1.4.1.9.9.832.1.34
173
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
173 total| Object Name |
|---|
cie1000LldpMibThis is a private version of the LLDP MIB MODULE-IDENTITY .1.3.6.1.4.1.9.9.832.1.34 |
SNMPv2-CONFThis is a private version of the LLDP MIB NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.832.1.34 |
cie1000LldpMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.832.1.34.1 |
cie1000LldpConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.832.1.34.1.2 |
cie1000LldpConfigGlobal OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.832.1.34.1.2.1 |
cie1000LldpConfigGlobalReInitDelaySet the LLDP tx reinitialization delay in seconds. Valid range 1-10.
When a port is disabled, LLDP is disabled or the switch is rebooted, a
LLDP shutdown frame is transmitted to the neighboring units, signaling
that the LLDP information isn't valid anymore.
Tx reinitialization delay controls the amount of seconds between the
shutdown frame and a new LLDP initialization.rw CIE1000Unsigned16 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.1.1 |
cie1000LldpConfigGlobalMsgTxHoldSet the LLDP tx hold times . Valid range 2-10.
Each LLDP frame contains information about how long time the
information in the LLDP frame shall be considered valid. The LLDP
information valid period is set to tx hold times multiplied by tx
interval seconds.rw CIE1000Unsigned16 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.1.2 |
cie1000LldpConfigGlobalMsgTxIntervalSet the LLDP tx interval in seconds.
The switch periodically transmits LLDP frames to its neighbors for
having the network discovery information up-to-date. The interval
between each LLDP frame is determined by the tx Interval value.
Valid range 5-32768 seconds.rw CIE1000Unsigned16 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.1.3 |
cie1000LldpConfigGlobalTxDelaySet the LLDP tx delay in seconds. Valid range 1-8192.
If some configuration is changed (e.g. the IP address) a new LLDP frame
is transmitted, but the time between the LLDP frames will always be at
least the value of tx delay seconds.
Note: tx Delay cannot be larger than 1/4 of the tx interval.rw CIE1000Unsigned16 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.1.4 |
cie1000LldpConfigTableThis is a table to configure LLDP configurations for a specific
interface. SEQUENCE OF CIE1000LldpConfigEntry .1.3.6.1.4.1.9.9.832.1.34.1.2.2 |
cie1000LldpConfigEntryEach interface has a set of control parameters CIE1000LldpConfigEntry .1.3.6.1.4.1.9.9.832.1.34.1.2.2.1 |
cie1000LldpConfigIfIndexLogical interface number index.ro CIE1000InterfaceIndex (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.2.1.1 |
cie1000LldpConfigAdminStateSets the LLDP admin state for the interface.rw CIE1000lldpAdminState .1.3.6.1.4.1.9.9.832.1.34.1.2.2.1.3 |
cie1000LldpConfigCdpAwareEnables/disables CDP awareness for the interface.
CDP is Cisco's equivalent to LLDP.
The CDP operation is restricted to decoding incoming CDP frames (The
switch doesn't transmit CDP frames). CDP frames are only decoded if
LLDP on the port is enabled.
Only CDP TLVs that can be mapped to a corresponding field in the LLDP
neighbors' table are decoded. All other TLVs are discarded
(Unrecognized CDP TLVs and discarded CDP frames are not shown in the
LLDP statistics.).
CDP TLVs are mapped onto LLDP neighbors' table as shown below.
CDP TLV 'Device ID' is mapped to the LLDP 'Chassis ID' field.
CDP TLV 'Address' is mapped to the LLDP 'Management Address' field. The
CDP address TLV can contain multiple addresses, but only the first
address is shown in the LLDP neighbors table.
CDP TLV 'Port ID' is mapped to the LLDP 'Port ID' field.
CDP TLV 'Version and Platform' is mapped to the LLDP 'System
Description' field.
Both the CDP and LLDP support 'system capabilities', but the CDP
capabilities cover capabilities that are not part of the LLDP. These
capabilities are shown as 'others' in the LLDP neighbors' table.
If all ports have CDP awareness disabled the switch forwards CDP frames
received from neighbor devices. If at least one port has CDP awareness
enabled all CDP frames are terminated by the switch.
Note: When CDP awareness on a port is disabled the CDP information
isn't removed immediately, but gets removed when the hold time is
exceeded.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.2.1.4 |
cie1000LldpConfigOptionalTlvsEnables/Disables the LLDP optional TLVs. Bit mask, where setting the
bit to 1 means enable transmission of the corresponding TLV.
Bit 0 represents Port Description TLV.
Bit 1 represents System Name TLV.
Bit 2 represents System Description.
Bit 3 represents System Capabilities TLV.
Bit 4 represents Management Address TLV.rw CIE1000Unsigned8 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.2.1.5 |
cie1000LldpConfigSnmpNotificationEnaEnable/disable of SNMP Trap notification.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.2.1.6 |
cie1000LldpConfigMed OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.832.1.34.1.2.3 |
cie1000LldpConfigMedTableThis is a table to configure LLDP MEDIA configurations for a specific
interface. SEQUENCE OF CIE1000LldpConfigMedEntry .1.3.6.1.4.1.9.9.832.1.34.1.2.3.1 |
cie1000LldpConfigMedEntryEach interface has a set of control parameters CIE1000LldpConfigMedEntry .1.3.6.1.4.1.9.9.832.1.34.1.2.3.1.1 |
cie1000LldpConfigMedIfIndexLogical interface number index.ro CIE1000InterfaceIndex (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.3.1.1.1 |
cie1000LldpConfigMedOptionalTlvsEnables/Disables the LLDP optional TLVs. Bit mask, where setting the
bit to 1 means
enable transmission of the corresponding optional TLV.
Bit 0 represents the capabilities TLV.
Bit 1 represents the network Policy TLV.
Bit 2 represents the location TLV.
Bit 3 represents the PoE TLV.rw CIE1000Unsigned8 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.3.1.1.3 |
cie1000LldpConfigMedDeviceTypeSetting device type to configure the mode the device shall operate as.rw CIE1000lldpmedDeviceType .1.3.6.1.4.1.9.9.832.1.34.1.2.3.1.1.4 |
cie1000LldpConfigMedPolicyTableThis is a table to configure LLDP MED Policies for the device. SEQUENCE OF CIE1000LldpConfigMedPolicyEntry .1.3.6.1.4.1.9.9.832.1.34.1.2.3.2 |
cie1000LldpConfigMedPolicyEntryNetwork Policy Discovery enables the efficient discovery and diagnosis
of mismatch issues with the VLAN configuration, along with the
associated Layer 2 and Layer 3 attributes, which apply for a set of
specific protocol applications on that port. Improper network policy
configurations are a very significant issue in VoIP environments that
frequently result in voice quality degradation or loss of service.
Policies are only intended for use with applications that have specific
'real-time' network policy requirements, such as interactive voice
and/or video services. CIE1000LldpConfigMedPolicyEntry .1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1 |
cie1000LldpConfigMedPolicyLldpmedPolicyPolicy index.ro Integer32 .1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.1 |
cie1000LldpConfigMedPolicyApplicationTypeThe LLDP policy application type.rw CIE1000lldpmedRemoteNetworkPolicyApplicationType .1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.3 |
cie1000LldpConfigMedPolicyTaggedThe LLDP policy tagged flag. Defines if LLDP policy uses tagged VLAN.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.4 |
cie1000LldpConfigMedPolicyVlanIdThe LLDP policy VLAN ID. Only valid when policy 'Tagged' is TRUErw CIE1000Unsigned16 .1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.5 |
cie1000LldpConfigMedPolicyL2PriorityThe LLDP policy L2 priority.rw CIE1000Unsigned8 .1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.6 |
cie1000LldpConfigMedPolicyDscpThe LLDP policy DSCP.rw CIE1000Unsigned8 .1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.7 |
cie1000LldpConfigMedPolicyActionActionrw CIE1000RowEditorState (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.3.2.1.100 |
cie1000LldpConfigMedPolicyListTableEach interface can be mapped to multiple policies. Set to TRUE in order
to enable the corresponding policy to be transmitted at the interface.
It is a requirement that the policy is defined. SEQUENCE OF CIE1000LldpConfigMedPolicyListEntry .1.3.6.1.4.1.9.9.832.1.34.1.2.3.3 |
cie1000LldpConfigMedPolicyListEntryEach location information has a control parameter CIE1000LldpConfigMedPolicyListEntry .1.3.6.1.4.1.9.9.832.1.34.1.2.3.3.1 |
cie1000LldpConfigMedPolicyListIfIndexLogical interface number index.ro CIE1000InterfaceIndex (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.3.3.1.1 |
cie1000LldpConfigMedPolicyListLldpmedPolicyPolicy index.ro Integer32 .1.3.6.1.4.1.9.9.832.1.34.1.2.3.3.1.3 |
cie1000LldpConfigMedPolicyListLldpmedPoliciesListSet to TRUE assign the corresponding policy index to the interface.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.3.3.1.4 |
cie1000LldpConfigMedGlobal OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.832.1.34.1.2.3.4 |
cie1000LldpConfigMedGlobalFastRepeatCountNumber of times to repeat LLDP frame transmission at fast start
Rapid startup and Emergency Call Service Location Identification
Discovery of endpoints is a critically important aspect of VoIP systems
in general. In addition, it is best to advertise only those pieces of
information which are specifically relevant to particular endpoint
types (for example only advertise the voice network policy to permitted
voice-capable devices), both in order to conserve the limited LLDPU
space and to reduce security and system integrity issues that can come
with inappropriate knowledge of the network policy.
With this in mind LLDP-MED defines an LLDP-MED Fast Start interaction
between the protocol and the application layers on top of the protocol,
in order to achieve these related properties. Initially, a Network
Connectivity Device will only transmit LLDP TLVs in an LLDPDU. Only
after an LLDP-MED Endpoint Device is detected, will an LLDP-MED capable
Network Connectivity Device start to advertise LLDP-MED TLVs in
outgoing LLDPDUs on the associated port. The LLDP-MED application will
temporarily speed up the transmission of the LLDPDU to start within a
second, when a new LLDP-MED neighbor has been detected in order share
LLDP-MED information as fast as possible to new neighbors.
Because there is a risk of an LLDP frame being lost during transmission
between neighbors, it is recommended to repeat the fast start
transmission multiple times to increase the possibility of the
neighbors receiving the LLDP frame. With fast start repeat count it is
possible to specify the number of times the fast start transmission
would be repeated. The recommended value is 4 times, given that 4 LLDP
frames with a 1 second interval will be transmitted, when an LLDP frame
with new information is received.
It should be noted that LLDP-MED and the LLDP-MED Fast Start mechanism
is only intended to run on links between LLDP-MED Network Connectivity
Devices and Endpoint Devices, and as such does not apply to links
between LAN infrastructure elements, including Network Connectivity
Devices, or other types of links.rw CIE1000Unsigned8 .1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.1 |
cie1000LldpConfigMedGlobalLatitudeLatitude degrees in 2s-complement as specified in RFC 3825. Positive
numbers are north of the equator and negative numbers are south of the
equator.rw CIE1000Integer64 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.2 |
cie1000LldpConfigMedGlobalLongitudeLongitude degrees in 2s-complement as specified in RFC 3825. Positive
values are East of the prime meridian and negative numbers are West of
the prime meridian.rw CIE1000Integer64 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.3 |
cie1000LldpConfigMedGlobalAltitudeTypeSetting altitude type
Possible to select between two altitude types (floors or meters).
Meters are representing meters of altitude defined by the vertical
datum specified. Floors are representing altitude in a form more
relevant in buildings which have different floor-to-floor dimensions.
An altitude = 0.0 is meaningful even outside a building, and represents
ground level at the given latitude and longitude. Inside a building,
0.0 represents the floor level associated with ground level at the main
entrance.rw CIE1000lldpmedAltitudeType .1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.4 |
cie1000LldpConfigMedGlobalAltitudeAltitude value in 2s-complement as specified in RFC 3825rw Integer32 .1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.5 |
cie1000LldpConfigMedGlobalElinAddrEmergency Call Service ELIN identifier data format is defined to carry
the ELIN identifier as used during emergency call setup to a
traditional CAMA or ISDN trunk-based PSAP. This format consists of a
numerical digit string, corresponding to the ELIN to be used for
emergency calling. Maximum number of octets are 25.rw CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.6 |
cie1000LldpConfigMedGlobalDatumSetting datum to configure the datum (geodetic system) to use.
The Map Datum is used for the coordinates given in these options:
WGS84: (Geographical 3D) - World Geodesic System 1984, CRS Code 4327,
Prime Meridian Name: Greenwich.
NAD83/NAVD88: North American Datum 1983, CRS Code 4269, Prime Meridian
Name: Greenwich;The associated vertical datum is the North American
Vertical Datum of 1988 (NAVD88).This datum pair is to be used when
referencing locations on land, not near tidal water(which would use
Datum = NAD83/MLLW).
NAD83/MLLW: North American Datum 1983, CRS Code 4269, Prime Meridian
Name: Greenwich; The associated vertical datum is Mean Lower Low Water
(MLLW). This datum pair is to be used when referencing locations on
water/sea/ocean.rw CIE1000lldpmedDatumType .1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.7 |
cie1000LldpConfigMedGlobalCountryCodeThe two-letter ISO 3166 country code in capital ASCII letters -
Example: DK, DE or US.rw CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.2.3.4.8 |
cie1000LldpConfigMedLocationInfTableThe civic address location information. Each civic address can contain
up to 250 characters, but the total amount of characters for the
combined civic address locations must not exceed 250 bytes. Note: If an
civic address location is non-empty it uses the amount of characters
plus addition two characters. This is described in TIA1057, Section
10.2.4.3.2. SEQUENCE OF CIE1000LldpConfigMedLocationInfEntry .1.3.6.1.4.1.9.9.832.1.34.1.2.3.5 |
cie1000LldpConfigMedLocationInfEntryEach civic address type as defined in TIA1057, Section 3.4 in Annex B CIE1000LldpConfigMedLocationInfEntry .1.3.6.1.4.1.9.9.832.1.34.1.2.3.5.1 |
cie1000LldpConfigMedLocationInfLldpmedIndexCivic address type.
1 - State/National subdivisions
2 - County, parish, gun (JP), district (IN)
3 - City, township
4 - City division, borough, city district, ward, chou (JP)
5 - Neighborhood, block
6 - Street
16 - Leading street direction
17 - Trailing street direction
18 - Street suffix
19 - House number
20 - House number suffix
21 - Landmark or vanity address
22 - Additional location information
23 - Name
24 - Postal/zip code
25 - Building
26 - Unit
27 - Floor
28 - Room
29 - Place type
30 - Postal
31 - Post office
32 - Additional codero CIE1000lldpmedCivicAddressType .1.3.6.1.4.1.9.9.832.1.34.1.2.3.5.1.2 |
cie1000LldpConfigMedLocationInfCivicAddressCivic addressrw CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.2.3.5.1.3 |
cie1000LldpConfigMedPolicyRowEditor OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.832.1.34.1.2.3.6 |
cie1000LldpConfigMedPolicyRowEditorLldpmedPolicyPolicy index.rw Integer32 .1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.1 |
cie1000LldpConfigMedPolicyRowEditorApplicationTypeThe LLDP policy application type.rw CIE1000lldpmedRemoteNetworkPolicyApplicationType .1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.3 |
cie1000LldpConfigMedPolicyRowEditorTaggedThe LLDP policy tagged flag. Defines if LLDP policy uses tagged VLAN.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.4 |
cie1000LldpConfigMedPolicyRowEditorVlanIdThe LLDP policy VLAN ID. Only valid when policy 'Tagged' is TRUErw CIE1000Unsigned16 .1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.5 |
cie1000LldpConfigMedPolicyRowEditorL2PriorityThe LLDP policy L2 priority.rw CIE1000Unsigned8 .1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.6 |
cie1000LldpConfigMedPolicyRowEditorDscpThe LLDP policy DSCP.rw CIE1000Unsigned8 .1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.7 |
cie1000LldpConfigMedPolicyRowEditorActionActionrw CIE1000RowEditorState (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.2.3.6.100 |
cie1000LldpStatus OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.832.1.34.1.3 |
cie1000LldpStatusStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.832.1.34.1.3.1 |
cie1000LldpStatusStatisticsGlobalCounters OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.832.1.34.1.3.1.1 |
cie1000LldpStatusStatisticsGlobalCountersTableInsertsShows the number of new entries added since switch reboot.ro Unsigned32 .1.3.6.1.4.1.9.9.832.1.34.1.3.1.1.1 |
cie1000LldpStatusStatisticsGlobalCountersTableDeletesShows the number of new entries deleted since switch reboot.ro Unsigned32 .1.3.6.1.4.1.9.9.832.1.34.1.3.1.1.2 |
cie1000LldpStatusStatisticsGlobalCountersTableDropsShows the number of LLDP frames dropped due to the entry table being
full.ro Unsigned32 .1.3.6.1.4.1.9.9.832.1.34.1.3.1.1.3 |
cie1000LldpStatusStatisticsGlobalCountersTableAgeOutsShows the number of entries deleted due to Time-To-Live expiring.ro Unsigned32 .1.3.6.1.4.1.9.9.832.1.34.1.3.1.1.4 |
cie1000LldpStatusStatisticsGlobalCountersLastChangeTimeShows the time when the last entry was last deleted or added. It also
shows the time elapsed since the last change was detected.ro CIE1000Unsigned64 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.1.1.5 |
cie1000LldpStatusStatisticsTableThis table represents the LLDP interface counters SEQUENCE OF CIE1000LldpStatusStatisticsEntry .1.3.6.1.4.1.9.9.832.1.34.1.3.1.2 |
cie1000LldpStatusStatisticsEntryEach port interface has a set of statistics counters CIE1000LldpStatusStatisticsEntry .1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1 |
cie1000LldpStatusStatisticsIfIndexLogical interface number index.ro CIE1000InterfaceIndex (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.1 |
cie1000LldpStatusStatisticsTxTotalShows the number of LLDP frames transmitted.ro Unsigned32 .1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.2 |
cie1000LldpStatusStatisticsRxTotalShows the number of LLDP frames received.ro Unsigned32 .1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.3 |
cie1000LldpStatusStatisticsRxErrorShows the number of received LLDP frames containing some kind of error.ro Unsigned32 .1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.4 |
cie1000LldpStatusStatisticsRxDiscardedShow the number of LLDP frames discarded. If a LLDP frame is received
at an interface, and the switch's internal table has run full, the LLDP
frame is counted and discarded. This situation is known as 'Too Many
Neighbors' in the LLDP standard. LLDP frames require a new entry in the
table when the Chassis ID or Remote Port ID is not already contained
within the table. Entries are removed from the table when a given
interface's link is down, an LLDP shutdown frame is received, or when
the entry ages out.ro Unsigned32 .1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.5 |
cie1000LldpStatusStatisticsTLVsDiscardedShows the number of TLVs discarded. Each LLDP frame can contain
multiple pieces of information, known as TLVs (TLV is short for 'Type
Length Value'). If a TLV is malformed, it is counted and discarded.ro Unsigned32 .1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.6 |
cie1000LldpStatusStatisticsTLVsUnrecognizedShows the number of well-formed TLVs, but with an unknown type value.ro Unsigned32 .1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.7 |
cie1000LldpStatusStatisticsTLVsOrgDiscardedShows the number of well-formed TLVs, but with an organizationally TLV
which is not supported.ro Unsigned32 .1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.8 |
cie1000LldpStatusStatisticsAgeOutsShow the number of age-outs. Each frame contains information about how
long time the LLDP information is valid (age-out time). If no new LLDP
frame is received within the age out time, the information is removed,
and the counter is incremented.ro Unsigned32 .1.3.6.1.4.1.9.9.832.1.34.1.3.1.2.1.9 |
cie1000LldpStatusNeighborsInfTableThis is a table to show the LLDP neighbors information for a specific
interface. SEQUENCE OF CIE1000LldpStatusNeighborsInfEntry .1.3.6.1.4.1.9.9.832.1.34.1.3.2 |
cie1000LldpStatusNeighborsInfEntryEach interface has a set of neighbors information CIE1000LldpStatusNeighborsInfEntry .1.3.6.1.4.1.9.9.832.1.34.1.3.2.1 |
cie1000LldpStatusNeighborsInfIfIndexLogical interface number index.ro CIE1000InterfaceIndex (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.1 |
cie1000LldpStatusNeighborsInfLldpmedIndexNeighbor information table entry index.ro Integer32 .1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.2 |
cie1000LldpStatusNeighborsInfChassisIdShows the LLDP neighbor's chassis Id.ro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.4 |
cie1000LldpStatusNeighborsInfPortIdShows the LLDP neighbor's port id.ro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.5 |
cie1000LldpStatusNeighborsInfPortDescriptionShows the LLDP neighbor's port description.ro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.6 |
cie1000LldpStatusNeighborsInfSystemNameShows the LLDP neighbor's system name.ro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.7 |
cie1000LldpStatusNeighborsInfSystemDescriptionShows the LLDP neighbor's system description.ro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.8 |
cie1000LldpStatusNeighborsInfSystemCapabilitiesShows the LLDP neighbor's system capabilities as bit mask.
If the bit is set, it means that the functionality is supported by the
neighbor system.
Bit 0 represents Other.
Bit 1 represents Repeater.
Bit 2 represents Bridge.
Bit 3 represents WLAN Access Point.
Bit 4 represents Router.
Bit 5 represents Telephone.
Bit 6 represents DOCSIS cable device.
Bit 7 represents Station Only.
Bit 8 represents Reserved.ro CIE1000Unsigned16 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.9 |
cie1000LldpStatusNeighborsInfSystemCapabilitiesEnableShows the LLDP neighbor's system capabilities which is enabled.
If the bit is set, it means that the functionality is currently enabled
at the neighbor system.
Bit 0 represents Other.
Bit 1 represents Repeater.
Bit 2 represents Bridge.
Bit 3 represents WLAN Access Point.
Bit 4 represents Router.
Bit 5 represents Telephone.
Bit 6 represents DOCSIS cable device.
Bit 7 represents Station Only.
Bit 8 represents Reserved.ro CIE1000Unsigned16 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.2.1.10 |
cie1000LldpStatusNeighborsMgmtInfTableThis is a table to show the LLDP neighbors information for a specific
interface. SEQUENCE OF CIE1000LldpStatusNeighborsMgmtInfEntry .1.3.6.1.4.1.9.9.832.1.34.1.3.3 |
cie1000LldpStatusNeighborsMgmtInfEntryEach interface has a set of neighbors information CIE1000LldpStatusNeighborsMgmtInfEntry .1.3.6.1.4.1.9.9.832.1.34.1.3.3.1 |
cie1000LldpStatusNeighborsMgmtInfIfIndexLogical interface number index.ro CIE1000InterfaceIndex (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.1 |
cie1000LldpStatusNeighborsMgmtInfLldpmedIndexNeighbor information table entry index.ro Integer32 .1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.2 |
cie1000LldpStatusNeighborsMgmtInfLldpManagementNeighbor management information table entry index.ro Integer32 .1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.4 |
cie1000LldpStatusNeighborsMgmtInfSystemMgmAddressSubtypeLLDP neighbor's management address subtype , section 9.5.9.3
IEEE802.1AB-2005.ro CIE1000Unsigned8 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.5 |
cie1000LldpStatusNeighborsMgmtInfSystemMgmtAddressLLDP neighbor's management address string, section 9.5.9.4
IEEE802.1AB-2005.ro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.6 |
cie1000LldpStatusNeighborsMgmtInfSystemMgmtInterfaceSubtypeInterface numbering subtype, section 9.5.9.5 IEEE802.1AB-2005.ro Integer32 .1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.7 |
cie1000LldpStatusNeighborsMgmtInfSystemMgmtInterfaceInterface number, section 9.5.9.6 IEEE802.1AB-2005.ro Integer32 .1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.8 |
cie1000LldpStatusNeighborsMgmtInfSystemMgmtOidObject identifier, section 9.5.9.8 IEEE802.1AB-2005.ro OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.832.1.34.1.3.3.1.9 |
cie1000LldpStatusMed OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.832.1.34.1.3.4 |
cie1000LldpStatusMedRemoteDeviceInfoTableThis is a table to show the LLDP neighbors information for a specific
interface. SEQUENCE OF CIE1000LldpStatusMedRemoteDeviceInfoEntry .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1 |
cie1000LldpStatusMedRemoteDeviceInfoEntryEach interface has a set of neighbors information CIE1000LldpStatusMedRemoteDeviceInfoEntry .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1 |
cie1000LldpStatusMedRemoteDeviceInfoIfIndexLogical interface number index.ro CIE1000InterfaceIndex (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.1 |
cie1000LldpStatusMedRemoteDeviceInfoLldpmedIndexNeighbor information table entry index.ro Integer32 .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.2 |
cie1000LldpStatusMedRemoteDeviceInfoCapabilitiesLLDP neighbor's capabilities bit mask.
Bit 0 represents LLDP-MED capabilities.
Bit 1 represents Network Policy.
Bit 2 represents Location Identification.
Bit 3 represents Extended Power via MDI - PSE.
Bit 4 represents Extended Power via MDI - PD
Bit 5 represents Inventoryro CIE1000Unsigned16 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.4 |
cie1000LldpStatusMedRemoteDeviceInfoCapabilitiesEnabledLLDP neighbor's capabilities bit mask for the capabilities which are
currently enabled.
Bit 0 represents LLDP-MED capabilities.
Bit 1 represents Network Policy.
Bit 2 represents Location Identification.
Bit 3 represents Extended Power via MDI - PSE.
Bit 4 represents Extended Power via MDI - PD
Bit 5 represents Inventoryro CIE1000Unsigned16 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.5 |
cie1000LldpStatusMedRemoteDeviceInfoLatitudeLatitude degrees in 2s-complement as specified in RFC 3825. Positive
numbers are north of the equator and negative numbers are south of the
equator.ro CIE1000Integer64 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.6 |
cie1000LldpStatusMedRemoteDeviceInfoLongitudeLongitude degrees in 2s-complement as specified in RFC 3825. Positive
values are East of the prime meridian and negative numbers are West of
the prime meridian.ro CIE1000Integer64 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.7 |
cie1000LldpStatusMedRemoteDeviceInfoAltitudeTypeAltitude type as either floors or meters. Meters are representing
meters of altitude defined by the vertical datum specified. Floors are
representing altitude in a form more relevant in buildings which have
different floor-to-floor dimensions. An altitude = 0.0 is meaningful
even outside a building, and represents ground level at the given
latitude and longitude. Inside a building, 0.0 represents the floor
level associated with ground level at the main entrance.ro CIE1000lldpmedAltitudeType .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.8 |
cie1000LldpStatusMedRemoteDeviceInfoAltitudeAltitude value in 2s-complement as specified in RFC 3825ro Integer32 .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.9 |
cie1000LldpStatusMedRemoteDeviceInfoDatumDatum (geodetic system) .
The Map Datum is used for the coordinates given in these options:
WGS84: (Geographical 3D) - World Geodesic System 1984, CRS Code 4327,
Prime Meridian Name: Greenwich.
NAD83/NAVD88: North American Datum 1983, CRS Code 4269, Prime Meridian
Name: Greenwich; The associated vertical datum is the North American
Vertical Datum of 1988 (NAVD88). This datum pair is to be used when
referencing locations on land, not near tidal water(which would use
Datum = NAD83/MLLW).
NAD83/MLLW: North American Datum 1983, CRS Code 4269, Prime Meridian
Name: Greenwich; The associated vertical datum is Mean Lower Low Water
(MLLW). This datum pair is to be used when referencing locations on
water/sea/ocean.ro CIE1000lldpmedDatumType .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.10 |
cie1000LldpStatusMedRemoteDeviceInfoElinaddrEmergency Call Service ELIN identifier data format is defined to carry
the ELIN identifier as used during emergency call setup to a
traditional CAMA or ISDN trunk-based PSAP. This format consists of a
numerical digit string, corresponding to the ELIN to be used for
emergency calling. Maximum number of octets are 25.ro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.11 |
cie1000LldpStatusMedRemoteDeviceInfoDeviceTypeShows the LLDP neighbor's device type.ro CIE1000lldpmedRemoteDeviceType .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.12 |
cie1000LldpStatusMedRemoteDeviceInfoHwRevShows the LLDP neighbor's hardware revision.ro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.13 |
cie1000LldpStatusMedRemoteDeviceInfoFwRevShows the LLDP neighbor's firmware revision.ro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.14 |
cie1000LldpStatusMedRemoteDeviceInfoSwRevShows the LLDP neighbor's software revision.ro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.15 |
cie1000LldpStatusMedRemoteDeviceInfoSerialNoShows the LLDP neighbor's serial number.ro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.16 |
cie1000LldpStatusMedRemoteDeviceInfoManufacturerNameShows the LLDP neighbor's manufacturer name.ro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.17 |
cie1000LldpStatusMedRemoteDeviceInfoModelNameShows the LLDP neighbor's model name.ro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.18 |
cie1000LldpStatusMedRemoteDeviceInfoAssetIdShows the LLDP neighbor's asset id.ro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.19 |
cie1000LldpStatusMedRemoteDeviceInfoEeeRxTwSysShows the LLDP neighbor's Receive tw_sys_rx . Tw_sys_rx is defined as
the time (expressed in microseconds) that the transmitting link partner
will wait before it starts transmitting data after leaving the Low
Power Idle (LPI) mode. Section 79.3.5.2, IEEE802.3az.ro CIE1000Unsigned16 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.20 |
cie1000LldpStatusMedRemoteDeviceInfoEeeTxTwSysShows the LLDP neighbor's Transmit Tw_sys_tx . Tw_sys_tx is defined as
the time (expressed in microseconds) that the receiving link partner is
requesting the transmitting link partner to wait before starting the
transmission data following the Low Power Idle (LPI) mode. Section
79.3.5.1, IEEE802.3az.ro CIE1000Unsigned16 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.21 |
cie1000LldpStatusMedRemoteDeviceInfoEeeFbTwSysShows the LLDP neighbor's Fallback tw_sys_tx. A receiving link partner
may inform the transmitter of an alternate desired Tw_sys_tx. Since a
receiving link partner is likely to have discrete levels for savings,
this provides the transmitter with additional information that it may
use for a more efficient allocation. Section 79.3.5.3, IEEE802.3az.ro CIE1000Unsigned16 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.22 |
cie1000LldpStatusMedRemoteDeviceInfoEeeTxTwSysEchoShows the LLDP neighbor's echo transmit Tw. The respective echo values
shall be defined as the local link partners reflection (echo) of the
remote link partners respective values. When a local link partner
receives its echoed values from the remote link partner it can
determine whether or not the remote link partner has received,
registered, and processed its most recent values. Section 79.3.5.4,
IEEE802.3az.ro CIE1000Unsigned16 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.23 |
cie1000LldpStatusMedRemoteDeviceInfoEeeRxTwSysEchoShows the LLDP neighbor's echo receive Tw. The respective echo values
shall be defined as the local link partners reflection (echo) of the
remote link partners respective values. When a local link partner
receives its echoed values from the remote link partner it can
determine whether or not the remote link partner has received,
registered, and processed its most recent values. Section 79.3.5.4,
IEEE802.3az.ro CIE1000Unsigned16 (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.4.1.1.24 |
cie1000LldpStatusMedRemoteDeviceLocInfoTableThis is a table to show the LLDP-MED remote device (neighbor) civic
location information for a specific interface. SEQUENCE OF CIE1000LldpStatusMedRemoteDeviceLocInfoEntry .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2 |
cie1000LldpStatusMedRemoteDeviceLocInfoEntryEach interface has a set of neighbors information CIE1000LldpStatusMedRemoteDeviceLocInfoEntry .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1 |
cie1000LldpStatusMedRemoteDeviceLocInfoIfIndexLogical interface number index.ro CIE1000InterfaceIndex (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.1 |
cie1000LldpStatusMedRemoteDeviceLocInfoLldpmedIndexNeighbor information table entry index.ro Integer32 .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.2 |
cie1000LldpStatusMedRemoteDeviceLocInfoStateNational subdivisionro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.5 |
cie1000LldpStatusMedRemoteDeviceLocInfoCountyCountyro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.6 |
cie1000LldpStatusMedRemoteDeviceLocInfoCityCityro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.7 |
cie1000LldpStatusMedRemoteDeviceLocInfoDistrictCity districtro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.8 |
cie1000LldpStatusMedRemoteDeviceLocInfoBlockBlock (Neighborhood)ro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.9 |
cie1000LldpStatusMedRemoteDeviceLocInfoStreetStreetro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.10 |
cie1000LldpStatusMedRemoteDeviceLocInfoLeadingStreetDirectionStreet Directionro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.11 |
cie1000LldpStatusMedRemoteDeviceLocInfoTrailingStreetSuffixTrailing Street Suffixro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.12 |
cie1000LldpStatusMedRemoteDeviceLocInfoStreetSuffixStreet Suffixro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.13 |
cie1000LldpStatusMedRemoteDeviceLocInfoHouseNoHouse No.ro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.14 |
cie1000LldpStatusMedRemoteDeviceLocInfoHouseNoSuffixHouse No. Suffixro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.15 |
cie1000LldpStatusMedRemoteDeviceLocInfoLandmarkLandmarkro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.16 |
cie1000LldpStatusMedRemoteDeviceLocInfoAdditionalInfoAdditional Location Inforo CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.17 |
cie1000LldpStatusMedRemoteDeviceLocInfoNameNamero CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.18 |
cie1000LldpStatusMedRemoteDeviceLocInfoZipCodeZip codero CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.19 |
cie1000LldpStatusMedRemoteDeviceLocInfoBuildingBuildingro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.20 |
cie1000LldpStatusMedRemoteDeviceLocInfoApartmentApartment/unitro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.21 |
cie1000LldpStatusMedRemoteDeviceLocInfoFloorFloorro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.22 |
cie1000LldpStatusMedRemoteDeviceLocInfoRoomNumberRoom Numberro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.23 |
cie1000LldpStatusMedRemoteDeviceLocInfoPlaceTypePlace typero CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.24 |
cie1000LldpStatusMedRemoteDeviceLocInfoPostalCommunityNamePostal Community Namero CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.25 |
cie1000LldpStatusMedRemoteDeviceLocInfoPoBoxPost Office Boxro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.26 |
cie1000LldpStatusMedRemoteDeviceLocInfoAdditionalCodeAdditional Codero CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.27 |
cie1000LldpStatusMedRemoteDeviceLocInfoCountryCodeThe two-letter ISO 3166 country code in capital ASCII letters -
Example: DK, DE or US.ro CIE1000DisplayString .1.3.6.1.4.1.9.9.832.1.34.1.3.4.2.1.28 |
cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoTableThis is a table to show the LLDP-MED remote device (neighbor) network
policies information for a specific interface. SEQUENCE OF CIE1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry .1.3.6.1.4.1.9.9.832.1.34.1.3.4.3 |
cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntryEach interface has a set of neighbors information CIE1000LldpStatusMedRemoteDeviceNetworkPolicyInfoEntry .1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1 |
cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoIfIndexLogical interface number index.ro CIE1000InterfaceIndex (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.1 |
cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoLldpmedIndexNeighbor information table entry index.ro Integer32 .1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.2 |
cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoLldpmedPolicyPolicy index.ro Integer32 .1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.3 |
cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoApplicationTypeThe LLDP policy application type.ro CIE1000lldpmedRemoteNetworkPolicyApplicationType .1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.5 |
cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoUnknownPolicyPolicy indicates that an Endpoint Device wants to explicitly advertise
that the policy is required by the device. Can be either Defined or
Unknown
Unknown: The network policy for the specified application type is
currently unknown.
Defined: The network policy is defined (known).ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.6 |
cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoTaggedDefines if LLDP policy uses tagged VLAN.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.7 |
cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoVlanIdThe policy VLAN ID. Only valid when policy 'Tagged' is TRUEro CIE1000Unsigned16 .1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.8 |
cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoL2PriorityShows the LLDP neighbor's policy L2 priority.ro CIE1000Unsigned8 .1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.9 |
cie1000LldpStatusMedRemoteDeviceNetworkPolicyInfoDscpLLDP policy DSCP.ro CIE1000Unsigned8 .1.3.6.1.4.1.9.9.832.1.34.1.3.4.3.1.10 |
cie1000LldpControl OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.832.1.34.1.4 |
cie1000LldpControlStatisticsClear OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.832.1.34.1.4.1 |
cie1000LldpControlStatisticsClearTableThis is a table to clear LLDP statistics for a specific interface. SEQUENCE OF CIE1000LldpControlStatisticsClearEntry .1.3.6.1.4.1.9.9.832.1.34.1.4.1.1 |
cie1000LldpControlStatisticsClearEntryEach interface has a set of statistics counters CIE1000LldpControlStatisticsClearEntry .1.3.6.1.4.1.9.9.832.1.34.1.4.1.1.1 |
cie1000LldpControlStatisticsClearIfIndexLogical interface number index.ro CIE1000InterfaceIndex (CIE1000-TC) .1.3.6.1.4.1.9.9.832.1.34.1.4.1.1.1.1 |
cie1000LldpControlStatisticsClearStatisticsClearSet to TRUE to clear the LLDP statistics of an interface.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.832.1.34.1.4.1.1.1.2 |
cie1000LldpControlStatisticsClearGlobal OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.832.1.34.1.4.1.2 |
cie1000LldpControlStatisticsClearGlobalClearSet to TRUE to clear the LLDP global statistics.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.832.1.34.1.4.1.2.1 |
cie1000LldpMibConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.832.1.34.2 |
cie1000LldpMibCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.832.1.34.2.1 |
cie1000LldpMibGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.832.1.34.2.2 |