CERENT-OPTICAL-MONITOR-MIB
AI MIB Summary
The CERENT-OPTICAL-MONITOR-MIB enables SNMP-based monitoring of optical interface characteristics, such as received and transmitted optical power, laser bias current, and temperature, while allowing administrators to configure alarm thresholds for these parameters on Cerent network elements. This module serves as a vendor-specific adaptation of the Cisco Optical Monitor MIB to facilitate granular physical layer fault detection and performance tracking on Cerent optical transport hardware.
This MIB module defines objects to monitor optical characteristics and set corresponding thresholds, on the optical interfaces in a network element. This module is an adaptation of CISCO-OPTICAL-MONITOR-MIB.
Main OID:
cerentOpticalMonitorMIB.1.3.6.1.4.1.3607.1.10.70
38
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
38 total| Object Name |
|---|
cerentOpticalMonitorMIBThis MIB module defines objects to monitor optical
characteristics and set corresponding thresholds, on the
optical interfaces in a network element.
This module is an adaptation of CISCO-OPTICAL-MONITOR-MIB. MODULE-IDENTITY .1.3.6.1.4.1.3607.1.10.70 |
cerentOpticalMonitorMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.3607.2.30 |
cerentOpticalMonGroup OBJECT IDENTIFIER .1.3.6.1.4.1.3607.2.30.1 |
cOpticalMonTableThis table provides objects to monitor optical
parameters in a network element. It also provides
objects for setting high and low threshold levels, with
configurable severities, on these monitored parameters. SEQUENCE OF COpticalMonEntry .1.3.6.1.4.1.3607.2.30.1.1 |
cOpticalMonEntryAn entry in the cOpticalMonTable provides objects to
monitor an optical parameter and set threshold levels
on that parameter, at an optical interface.
Note that the set of monitored optical parameters may vary
based on interface type and direction.
Examples of interfaces that can have an entry in this table
include optical transceivers optical amplifiers,
and optical attenuators. COpticalMonEntry .1.3.6.1.4.1.3607.2.30.1.1.1 |
cOpticalMonDirectionThis object is an index into the cOpticalMonTable
and indicates the direction monitored for the
optical interface, in this entry. OpticalIfDirection .1.3.6.1.4.1.3607.2.30.1.1.1.1 |
cOpticalMonParameterTypeThis object is an index into the cOpticalMonTable
and specifies the optical parameter that is being monitored,
in this entry. OpticalParameterType .1.3.6.1.4.1.3607.2.30.1.1.1.2 |
cOpticalParameterValueThis object gives the value measured for the particular
optical parameter specified by the cOpticalMonParameterType
object.ro OpticalParameterValue .1.3.6.1.4.1.3607.2.30.1.1.1.3 |
cOpticalParamHighAlarmThreshThis object is used to set a high alarm threshold on the
optical parameter being monitored.
If the measured value of the parameter,is greater than the
value configured in this object, an alarm will be raised.
When the cOpticalMonParameterType object is set to 'power'
for the receive direction at a transceiver, this object
specifies the receiver saturation level.rw OpticalParameterValue .1.3.6.1.4.1.3607.2.30.1.1.1.4 |
cOpticalParamHighWarning15MinThreshThis object is used to set a high warning 15 minute threshold
on the optical parameter being monitored.
If the measured value of the parameter,is greater than the
value configured in this object, an alarm may be raised.rw OpticalParameterValue .1.3.6.1.4.1.3607.2.30.1.1.1.5 |
cOpticalParamHighWarning1DayThreshThis object is used to set a high warning 1 day threshold on
the optical parameter being monitored.
If the measured value of the parameter,is greater than the
value configured in this object, an alarm may be raised.rw OpticalParameterValue .1.3.6.1.4.1.3607.2.30.1.1.1.6 |
cOpticalParamLowAlarmThreshThis object is used to set a low alarm threshold on the
optical parameter being monitored.
If the measured value of the parameter,goes lower than the
value configured in this object, an alarm will be raised.
When the cOpticalMonParameterType object is set to 'power'
for the receive direction and when the interface supports
alarms based on loss of light, this object specifies the
optical power threshold for declaring loss of light. Also,
when optical amplifiers are present in the network, in the
receive direction, this value may need to be configured,
since the noise floor may be higher than the minimum
sensitivity of the receiver.rw OpticalParameterValue .1.3.6.1.4.1.3607.2.30.1.1.1.7 |
cOpticalParamLowWarning15MinThreshThis object is used to set a low warning 15 minute threshold
on the optical parameter being monitored.
If the measured value of the parameter,goes lower than the
value configured in this object, an alarm will be raised.rw OpticalParameterValue .1.3.6.1.4.1.3607.2.30.1.1.1.8 |
cOpticalParamLowWarning1DayThreshThis object is used to set a low warning 1 day threshold
on the optical parameter being monitored.
If the measured value of the parameter,goes lower than the
value configured in this object, an alarm will be raised.rw OpticalParameterValue .1.3.6.1.4.1.3607.2.30.1.1.1.9 |
cOpticalParamLowDegradeThreshThis object is used to set a low degrade threshold
on the optical parameter being monitored.
If the measured value of the parameter,goes lower than the
value configured in this object, a degrade alarm will be raised.rw OpticalParameterValue .1.3.6.1.4.1.3607.2.30.1.1.1.10 |
cOpticalParamHighDegradeThreshThis object is used to set a high degrade threshold
on the optical parameter being monitored.
If the measured value of the parameter,goes lower than the
value configured in this object, a degrade alarm will be raised.rw OpticalParameterValue .1.3.6.1.4.1.3607.2.30.1.1.1.11 |
cerentOpticalPMGroup OBJECT IDENTIFIER .1.3.6.1.4.1.3607.2.30.2 |
cOpticalPMCurrentTableThis table stores performance monitoring data for the
various optical parameters, collected over the current
interval. SEQUENCE OF COpticalPMCurrentEntry .1.3.6.1.4.1.3607.2.30.2.1 |
cOpticalPMCurrentEntryAn entry in the cOpticalPMCurrentTable. It contains
performance monitoring data for an optical parameter,
collected over the current interval.
Note that the set of monitored optical parameters may vary
based on interface type and direction.
Examples of interfaces that can have an entry in this table
include optical transceivers, optical amplifiers, and optical
attenuators. COpticalPMCurrentEntry .1.3.6.1.4.1.3607.2.30.2.1.1 |
cOpticalPMCurrentDirectionThis object is an index into the cOpticalPMCurrentTable
and indicates the direction monitored
for the optical interface, in this entry. OpticalIfDirection .1.3.6.1.4.1.3607.2.30.2.1.1.1 |
cOpticalPMCurrentParamTypeThis object is an index into the
cOpticalPMCurrentTable and specifies the optical parameter
that is being monitored, in this entry. OpticalParameterType .1.3.6.1.4.1.3607.2.30.2.1.1.2 |
cOpticalPMCurrentPeriodThis object is an index into the
cOpticalPMCurrentTable and indicates whether the
optical parameter values given in this entry, are collected
over a period of 15 minutes or 24 hours. CerentPeriod (CERENT-TC) .1.3.6.1.4.1.3607.2.30.2.1.1.3 |
cOpticalPMCurrentMaxParamThis object gives the maximum value measured for the optical
parameter, in the current 15 minute or 24 hour interval.ro OpticalParameterValue .1.3.6.1.4.1.3607.2.30.2.1.1.4 |
cOpticalPMCurrentMinParamThis object gives the minimum value measured for the optical
parameter, in the current 15 minute or 24 hour interval.ro OpticalParameterValue .1.3.6.1.4.1.3607.2.30.2.1.1.5 |
cOpticalPMCurrentMeanParamThis object gives the average value of the measured optical
parameter, in the current 15 minute or 24 hour interval.ro OpticalParameterValue .1.3.6.1.4.1.3607.2.30.2.1.1.6 |
cOpticalPMIntervalTableThis table stores performance monitoring data for the
various optical parameters, collected over current and
previous intervals.
This table can have entries for up to 96 complete 15 minute
intervals. SEQUENCE OF COpticalPMIntervalEntry .1.3.6.1.4.1.3607.2.30.2.2 |
cOpticalPMIntervalEntryAn entry in the cOpticalPMIntervalTable. It contains
performance monitoring data for an optical parameter,
collected over current and previous intervals.
Note that the set of monitored optical parameters may vary
based on interface type and direction.
Examples of interfaces that can have an entry in this table
include optical transceivers, optical amplifiers, and optical
attenuators. COpticalPMIntervalEntry .1.3.6.1.4.1.3607.2.30.2.2.1 |
cOpticalPMIntervalDirectionThis object is an index into the cOpticalPMIntervalTable
and indicates the direction monitored
for the optical interface, in this entry. OpticalIfDirection .1.3.6.1.4.1.3607.2.30.2.2.1.1 |
cOpticalPMIntervalParamTypeThis object is an index into the
cOpticalPMIntervalTable and specifies the optical parameter
that is being monitored, in this entry. OpticalParameterType .1.3.6.1.4.1.3607.2.30.2.2.1.2 |
cOpticalPMIntervalPeriodThis object is an index into the
cOpticalPMIntervalTable and indicates whether the
optical parameter values given in this entry, are collected
over a period of 15 minutes or 24 hours. CerentPeriod (CERENT-TC) .1.3.6.1.4.1.3607.2.30.2.2.1.3 |
cOpticalPMIntervalNumberThis object is an index into the cOpticalPMIntervalTable.
It is a number between 1 and 96, which identifies the
interval for which the set of optical parameter values is
available. The interval identified by 1 is the most recent
15 minute or 24 hour interval, and the interval
identified by N is the interval immediately preceding the one
identified by N-1. Integer32 .1.3.6.1.4.1.3607.2.30.2.2.1.4 |
cOpticalPMIntervalMaxParamThis object gives the maximum value measured for the optical
parameter, in a particular 15 minute or 24 hour interval.ro OpticalParameterValue .1.3.6.1.4.1.3607.2.30.2.2.1.5 |
cOpticalPMIntervalMinParamThis object gives the minimum value measured for the optical
parameter, in a particular 15 minute or 24 hour interval.ro OpticalParameterValue .1.3.6.1.4.1.3607.2.30.2.2.1.6 |
cOpticalPMIntervalMeanParamThis object gives the average value of the measured optical
parameter, in a particular 15 minute or 24 hour interval.ro OpticalParameterValue .1.3.6.1.4.1.3607.2.30.2.2.1.7 |
cOpticalPMIntervalValidDataThis variable indicates if the data for this
interval is valid.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.3607.2.30.2.2.1.8 |
cerentOpticalMonitorMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.3607.5.20 |
cerentOpticalMonitorMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.3607.5.20.1 |
cerentOpticalMonitorMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.3607.5.20.2 |