CENTRECOM-QOS-MIB
Imported Objects
Objects
16 total| Object Name |
|---|
atiQosAtkk Quality-of-Service objects MODULE-IDENTITY .1.3.6.1.4.1.207.8.12.2.5 |
SNMPv2-SMIAtkk Quality-of-Service objects Unknown .1.3.6.1.4.1.207.8.12.2.5 |
atiQosCommon OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.12.2.5.1 |
atiQosModeIndicates which QoS mode the device should
use. ingress(1) applies priority-based QoS based
on the incoming packet's destination IP or MAC
address, 802.1p priority, PACE(tm), Source Port or
VLAN. egress(2) applies priority- and bandwidth-based
QoS based on destination IP or MAC address or VLAN.rw Enumeration .1.3.6.1.4.1.207.8.12.2.5.1.4 |
atiQosUnconfigureSetting this to true will reset all QoS settings
in the device to factory defaults. Reads from this
value return an undefined value.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.207.8.12.2.5.1.5 |
atiQosProfileTableThis table lists QoS profiles. SEQUENCE OF AtiQosProfileEntry .1.3.6.1.4.1.207.8.12.2.5.1.6 |
atiQosProfileEntryAn individual QoS profile Entry. AtiQosProfileEntry .1.3.6.1.4.1.207.8.12.2.5.1.6.1 |
atiQosProfileIndexAn index that uniquely identifies an entry in the
qos table.rw INTEGER .1.3.6.1.4.1.207.8.12.2.5.1.6.1.1 |
atiQosProfileNameA unique qos profile name.rw DisplayString .1.3.6.1.4.1.207.8.12.2.5.1.6.1.2 |
atiQosProfileMinBwThe minumum percentage of bandwidth that this queue requires.
The Switch is required to provide the minumum amount of
bandwidth to the queue. The lowest possible value is 0%.rw INTEGER .1.3.6.1.4.1.207.8.12.2.5.1.6.1.3 |
atiQosProfileMaxBwThe maximum percentage of bandwidth that this queue is
permitted to userw INTEGER .1.3.6.1.4.1.207.8.12.2.5.1.6.1.4 |
atiQosProfilePriorityThe level of priority in which this queue will be serviced
by the Switch.rw Enumeration .1.3.6.1.4.1.207.8.12.2.5.1.6.1.5 |
atiQosProfileRowStatusThe status of the atiQosProfile entry.
This OBJECT can be set to:
active(1)
createAndGo(4)
createAndWait(5)
destroy(6)
The following values may be read:
active(1)
notInService(2)
notReady(3).
Setting this object to createAndGo(4) causes the agent
to attempt to create and commit the row based on
the contents of the objects in the row. If all necessary
information is present in the row and the values are
acceptible to the agent, the agent will change the
status to active(1). If any of the necessary objects
are not available, the agent will reject the creation
request.
Setting this object to createAndWait(5) causes a row
in this table to be created. The agent sets the
status to notInService(2) if all of the information is
present in the row and the values are acceptable to the
agent; otherwise, the agent sets the status to
notReady(3).
Setting this object to active(1) is only valid when
the current status is active(1) or notInService(2).
When the state of the row transitions is set to active(1),
the agent creates the corresponding row in the ifTable..
Setting this object to destroy(6) will remove the corresponding
QoS Profile Entry.
In order for a set of this object to destroy(6) to succeed,
all dependencies on this row must have been removed. These
will include any stacking dependencies in the ifStackTable and
any protocol specific tables dependencies.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.207.8.12.2.5.1.6.1.6 |
atiQosByVlanMappingTableTable to associate a Vlan with the QoS profile that the
Vlan is using. Every Vlan is assigned a Qos Profile and
hence there is an entry in this table corresponding to every
entry in the atiVlanIfTable. SEQUENCE OF AtiQosByVlanMappingEntry .1.3.6.1.4.1.207.8.12.2.5.1.7 |
atiQosByVlanMappingEntryThe QoS associated with a particular Vlan. AtiQosByVlanMappingEntry .1.3.6.1.4.1.207.8.12.2.5.1.7.1 |
atiQosByVlanMappingQosProfileIndexValue of atiQosProfileIndex that uniquely
identifies a QoS Profile entry in atiQosProfileTable.
This indicates the QoS to be given to traffic for this
Vlan in the absence of any other more specific
configuration information for this traffic.rw INTEGER .1.3.6.1.4.1.207.8.12.2.5.1.7.1.1 |
More MIBs from Allied Telesis
Browse all Allied TelesisMIBs →The AT-UWC-WLAN-SWITCH-MIB provides vendor-specific SNMP management for Allied Telesis Universal Wireless Controller (UWC) hardware, enabling monitoring of WLAN switch operational states, interface statistics, and wireless client association metrics.
The AtiEdgeSwitch-MIB provides vendor-specific SNMP extensions for monitoring and managing Layer 2 stackable switch operations, including interface status, port statistics, and stack topology, on ATI hardware platforms within Windows and UNIX network management environments.
Standard SNMP MIB module defining data structures for ALLIEDTELESYN-MIB.
The AT-BOARDS-MIB module provides a structured OID hierarchy for monitoring and managing specific hardware components on Allied Telesis devices, including board identifiers, firmware release versions, interface type definitions, and integrated chip IDs. This MIB enables granular inventory tracking and hardware status verification by mapping logical identifiers to physical subsystems within the network equipment chassis.
SWITCH-ATM-MIB monitors and manages Asynchronous Transfer Mode (ATM) interfaces and virtual circuit states on network switches, specifically tracking VPI/VCI pairings and traffic counters under the constraint that the Virtual Path Identifier is fixed by the implementation and excluded from table indexing.
Standard SNMP MIB module defining data structures for AtiL2-MIB.