CAT2600-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for CAT2600-MIB.
151
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
151 total| Object Name |
|---|
cisco OBJECT IDENTIFIER .1.3.6.1.4.1.9 |
RFC1155-SMI Unknown .1.3.6.1.4.1.9 |
catProd OBJECT IDENTIFIER .1.3.6.1.4.1.9.1 |
cat2600 OBJECT IDENTIFIER .1.3.6.1.4.1.9.1.111 |
cat2600Ts OBJECT IDENTIFIER .1.3.6.1.4.1.9.1.111.1 |
cat2600TsObjectID OBJECT IDENTIFIER .1.3.6.1.4.1.9.1.111.1.1 |
cat2600TsSysObjectID OBJECT IDENTIFIER .1.3.6.1.4.1.9.1.111.1.1.1 |
cat2600TsObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.1.111.1.2 |
cat2600TsMain OBJECT IDENTIFIER .1.3.6.1.4.1.9.1.111.1.2.1 |
cat2600TsConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.1.111.1.2.1.1 |
cat2600TsFwVerThe firmware version in the form major.minor. For
port microcode (SOLO) version information see the
mgmt.mib-2.interfaces.ifTable.ifEntry.ifDescr object.ro DisplayString .1.3.6.1.4.1.9.1.111.1.2.1.1.1 |
cat2600TsHwVerThe hardware version in the form major.minor.ro DisplayString .1.3.6.1.4.1.9.1.111.1.2.1.1.2 |
cat2600TsSerialNumberSystem serial number.ro DisplayString .1.3.6.1.4.1.9.1.111.1.2.1.1.3 |
cat2600TsInstallationDateFirmware installation date. This date is initially
set by the Network Management station. Each time
the NV RAM is cleared through the console this date
needs to be set by the management station. This should
be in the format YYYY MM DD HH MM SS.rw DisplayString .1.3.6.1.4.1.9.1.111.1.2.1.1.4 |
cat2600TsFwSizeSize in bytes of the binary firmware image.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.1.1.5 |
cat2600TsFwCRCFirmware binary image CRC value.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.1.1.6 |
cat2600TsFwManufacturerFirmware manufacturer.ro DisplayString .1.3.6.1.4.1.9.1.111.1.2.1.1.7 |
cat2600TsIpAddrIP address of the switch. Changes to this object
take effect immediately.rw IpAddress .1.3.6.1.4.1.9.1.111.1.2.1.1.8 |
cat2600TsNetMaskIP subnet mask of the switch. Changes to this object
take effect immediately.rw IpAddress .1.3.6.1.4.1.9.1.111.1.2.1.1.9 |
cat2600TsDefaultGatewayIP default gateway used by the switch. Changes to this
object take effect immediately.rw IpAddress .1.3.6.1.4.1.9.1.111.1.2.1.1.10 |
cat2600TsTrapRcvrTableA table of managers to which to send traps.
Entries in the table are saved across resets and
power cycles. SEQUENCE OF Cat2600TsTrapRcvrEntry .1.3.6.1.4.1.9.1.111.1.2.1.1.14 |
cat2600TsTrapRcvrEntryDefinition of rows in the trap receiver table.
The column cat2600TsTrapRcvrStatus is used to create
and delete rows in the table. Creation requires
a SET PDU with objects cat2600TsTrapRcvrStatus,
cat2600TsTrapRcvrIpAddress, and cat2600TsTrapRcvrComm. Cat2600TsTrapRcvrEntry .1.3.6.1.4.1.9.1.111.1.2.1.1.14.1 |
cat2600TsTrapRcvrIndexThe index of the row in the table.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.1.1.14.1.1 |
cat2600TsTrapRcvrStatusSetting the value of this object to invalid(3)
deletes the row from the table. The value
invalid(3) should never be returned on a GET.
Setting this value to create(4) causes a new row
to be created if the row does not already exist.
To create a new row set cat2600TsTrapRcvrStatus to
create(4) and cat2600TsTrapRcvrIndex to the next
available index ( cat2600TsTrapRcvrNext ). After
successful creation of the new row, you can then
set the desired values for cat2600TsTrapRcvrIpAddress
and cat2600TsTrapRcvrComm.
The value returned on GETs should be valid(2) or
other(1), which is used to indicate any other
condition.rw Enumeration .1.3.6.1.4.1.9.1.111.1.2.1.1.14.1.2 |
cat2600TsTrapRcvrIpAddressIP address for an SNMP manager that is to receive the trap.rw IpAddress .1.3.6.1.4.1.9.1.111.1.2.1.1.14.1.3 |
cat2600TsTrapRcvrCommCommunity string to use.rw DisplayString .1.3.6.1.4.1.9.1.111.1.2.1.1.14.1.4 |
cat2600TsTrapRcvrDmnsDomains on which traps to this target are sent.
Each octet within the value of this object
specifies a set of eight domains, with the first
octet specifying domains 0 through 7, the second
octet specifying domains 8 through 15, etc.
Within each octet, the most significant bit
represents the lowest numbered domain, and the
least significant bit represents the highest
numbered domain. Thus, each domain is represented by a
single bit within the value of this object.
If that bit has a value of '1' then that domain is
included in the set of ports which will receive the trap;
the domain is not included if its bit has a value of '0'.rw OCTET STRING .1.3.6.1.4.1.9.1.111.1.2.1.1.14.1.5 |
cat2600TsPingIntervalThis variable specifies the interval in seconds of
sending ICMP Echo Requests to the default gateway.
No PING packets will be sent if the value is set to 0.
The default interval is 10 minutes.rw INTEGER .1.3.6.1.4.1.9.1.111.1.2.1.1.19 |
cat2600TsTapPortSelect the port to monitor traffic.rw INTEGER .1.3.6.1.4.1.9.1.111.1.2.1.1.20 |
cat2600TsTapMonitoredPortAllows the selection of the port that will be monitored by the
port selected by cat2600TsTapPort.rw INTEGER .1.3.6.1.4.1.9.1.111.1.2.1.1.21 |
cat2600TsCrcThresholdHiThreshold for the switch to change to store and
forward mode. A change in mode also generates a trap.rw INTEGER .1.3.6.1.4.1.9.1.111.1.2.1.1.22 |
cat2600TsCrcThresholdLowThreshold for the switch to change to store and
forward mode. A change in mode also generates a trap.rw INTEGER .1.3.6.1.4.1.9.1.111.1.2.1.1.23 |
cat2600TsPortSwitchModeChangeTrapEnableEnable or disable the trap sent out when the switching
mode changes from cut-through to store and forward.rw Enumeration .1.3.6.1.4.1.9.1.111.1.2.1.1.24 |
cat2600TsTrendThresholdBased on trend calculation of the Dynamic Cut State
algorithm, when this value is exceeded the port
changes from cut-through to store and forward mode.
The default value for this object is 8 events. The
valid range is 1-100.rw INTEGER -- ?? .1.3.6.1.4.1.9.1.111.1.2.1.1.25 |
cat2600TsSamplingPeriodSampling period in minutes for determining if the
error rate of CRC errors has been exceeded.
The default value for this object is 10 minutes. The
valid range is 1-120.rw INTEGER (1 ..120) .1.3.6.1.4.1.9.1.111.1.2.1.1.26 |
cat2600TsNumberUFCThe number of UFCs installed in the switch. A value
of zero (or an SNMP error of NOSUCH) indicates there are
NO UFCs installed in this switch.
This value indicates the number of entries in the
cat2600TsUFCTable.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.1.1.27 |
cat2600TsSys OBJECT IDENTIFIER .1.3.6.1.4.1.9.1.111.1.2.1.2 |
cat2600TsNumPortsThe maximum number of physical ports on the switch. This
value includes all base ports plus all ports on any UFC cards.
It does not include internally defined Bridge Relay Function
ports or the CPU 'interface'.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.1.2.1 |
cat2600TsNumStationsAggregate number of currently active stations
(nodes) on all ports on the switch.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.1.2.2 |
cat2600TsMostStationsHighest aggregate number of stations ever active
on all ports at one time, since the last reset or
power cycle. This includes the default MAC address
entries from each port.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.1.2.3 |
cat2600TsMaxStationsHighest aggregate number of stations which the
switch can support simultaneously.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.1.2.4 |
cat2600TsResetThis object is used to reset the switch. Writing
softReset(3) causes the switch to reset the
hardware, run quick diagnostics, clear all
counters, start switching, issue a warmstart trap,
and then be able to respond to SNMP requests.
Writing hardReset(2) causes the switch to run
power up diagnostics and then execute a soft
reset.
Note: all address tables are cleared in both cases.
The administrative parameters from nonvolatile memory are
used to initialize the operational parameters.
The value returned on GETs should be running(1).rw Enumeration .1.3.6.1.4.1.9.1.111.1.2.1.2.5 |
cat2600TsNumResetsNumber of soft resets the switch has executed
since the last hard reset or power cycle. Soft
resets are defined as writing softReset(3) to
cat2600TsReset, pressing the front panel reset button,
executing a soft reset from the console, or resets
induced by the switch firmware.ro Counter .1.3.6.1.4.1.9.1.111.1.2.1.2.6 |
cat2600TsAddrAgingTimeNumber of minutes of inactivity before an address
entity is aged out. A value of zero means no
aging. Note: if an address shows up on another
port, the original port to address assignment is
automatically deleted. The value is saved across
resets and power cycles. The default value for this
object is 5 minutes.rw INTEGER .1.3.6.1.4.1.9.1.111.1.2.1.2.7 |
cat2600TsSysTemperatureTemperature condition of the system. A change in this
value generates a TRAP.ro Enumeration .1.3.6.1.4.1.9.1.111.1.2.1.2.11 |
cat2600TsInstalledMemoryTotal amount of CPU memory installed (in megabytes).ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.1.2.12 |
cat2600TsSysCurTimeCurrent time at the switch. To set the time use the
format yyyy mm dd hh mm ss.
All fields are required.rw DisplayString .1.3.6.1.4.1.9.1.111.1.2.1.2.13 |
cat2600TsPort OBJECT IDENTIFIER .1.3.6.1.4.1.9.1.111.1.2.2 |
cat2600TsPortTableA table of information about each port. The number of rows
is given by cat2600TsNumPorts.
(This value refers to PHYSICAL ports as opposed to internal
logical CRF bridge ports.) SEQUENCE OF Cat2600TsPortEntry .1.3.6.1.4.1.9.1.111.1.2.2.1 |
cat2600TsPortEntryDefinition of rows in the port table. The number
of rows is determined by the hardware and is
specified by the value of cat2600TsNumPorts. Rows can
not be created or deleted via SNMP requests. Cat2600TsPortEntry .1.3.6.1.4.1.9.1.111.1.2.2.1.1 |
cat2600TsPortIndexThe ifIndex value corresponding to each port entry. For TR
interfaces, the TsPortIndex corresponds to the Port Number
or POE Index.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.2.1.1.1 |
cat2600TsPortRcvLocalFramesNumber of frames received where the destination is on this port.ro Counter .1.3.6.1.4.1.9.1.111.1.2.2.1.1.2 |
cat2600TsPortForwardedFramesNumber of frames received on this port and forwarded to
another port or the system module for processing.ro Counter .1.3.6.1.4.1.9.1.111.1.2.2.1.1.3 |
cat2600TsPortMostStationsHighest number of stations ever active at any
time since the last reset of the switch as seen by
this port. This includes the default MAC address entries
for the port.ro Counter .1.3.6.1.4.1.9.1.111.1.2.2.1.1.4 |
cat2600TsPortMaxStationsMaximum number of stations which the port can
support simultaneously.ro Counter .1.3.6.1.4.1.9.1.111.1.2.2.1.1.5 |
cat2600TsPortSWHandledFramesNumber of Frames received on this port and
delivered to the system module for processing.ro Counter .1.3.6.1.4.1.9.1.111.1.2.2.1.1.6 |
cat2600TsPortLocalStationsNumber of stations on this port's address table
which belong to the segment attached to this port.ro Counter .1.3.6.1.4.1.9.1.111.1.2.2.1.1.7 |
cat2600TsPortRemoteStationsNumber of stations on this port's address table
which belong to segments attached to other ports.ro Counter .1.3.6.1.4.1.9.1.111.1.2.2.1.1.8 |
cat2600TsPortUnknownStaFramesNumber of unicast frames received on this port
and forwarded to the system module for processing
because the source or destination station address
is not in the port's forwarding table.ro Counter .1.3.6.1.4.1.9.1.111.1.2.2.1.1.9 |
cat2600TsPortResetStatsSetting this object to reset(3) causes all
traffic counters for this port to be set to zero.
Also the value of cat2600TsPortResetTimer is set to
zero.rw Enumeration .1.3.6.1.4.1.9.1.111.1.2.2.1.1.10 |
cat2600TsPortResetTimerTime (in 100th second ticks) since the port
counters were reset.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.9.1.111.1.2.2.1.1.11 |
cat2600TsPortResetAddrsSetting this object to reset(3) clears all
address table entries for this port as well as
setting all port traffic counters to zero and
setting cat2600TsPortResetTimer to zero.rw Enumeration .1.3.6.1.4.1.9.1.111.1.2.2.1.1.12 |
cat2600TsPortRcvBcastsNumber of Broadcast Frames received on this port
without errors.ro Counter -- ?? RFC1573 bcst frames ?? .1.3.6.1.4.1.9.1.111.1.2.2.1.1.13 |
cat2600TsPortSwitchedFramesNumber of frames switched on this portro Counter .1.3.6.1.4.1.9.1.111.1.2.2.1.1.14 |
cat2600TsPortLinkStateLink state of the port.ro Enumeration .1.3.6.1.4.1.9.1.111.1.2.2.1.1.15 |
cat2600TsPortHashOverflowsNumber of times a hash bucket was full when trying to
add an entry to the port address table.ro Counter .1.3.6.1.4.1.9.1.111.1.2.2.1.1.16 |
cat2600TsPortAddrAgingTimePort level address aging time.rw INTEGER .1.3.6.1.4.1.9.1.111.1.2.2.1.1.17 |
cat2600TsPortSwitchModeOperational frame switching mode for the port. When
in auto mode the port uses the Direct Cut algorithm
to place the port in either cut-thru or store-and-
forward mode.
This object is equivalent to cPortProtocolCharFrameControlOption
in the dtrMac MIB. However, this object defines an
additional state -auto- not defined in that standard.rw Enumeration .1.3.6.1.4.1.9.1.111.1.2.2.1.1.18 |
cat2600TsPortFixedCfgUse fixed configuration or run auto detection
to determine configuration.rw Enumeration .1.3.6.1.4.1.9.1.111.1.2.2.1.1.19 |
cat2600TsPortModeWhen read, this object indicates the Port Mode
obtained by the auto-detect function. It is a
valid read object only when TsPortFixedCfg is set
to auto-detect(1) and TsPortLinkState indicates up(1).
Write to this object when defining the Port Mode for
a fixed configuration (TsPortFixedCfg set to fixed(2)).
This object is equivalent to the dtrMac MIB object
cPortProtocolCharOperationOption.rw Enumeration .1.3.6.1.4.1.9.1.111.1.2.2.1.1.20 |
cat2600TsPortDuplexVersion 1 MIB
When read, this object indicates the Port Duplex state
obtained by the auto-detect function.
This object is a valid read object any time that
TSPortLinkState indicates up(1) or when TsPortFixedCfg
indicates fixed(2).
Write to this object when defining the Port Duplex state
for a fixed configuration (TsPortFixedCfg set to fixed(2)).
Version 2 MIB
This object is related to the dtrMac MIB objects
cPortProtocolCharCurrentAccessProtocol
and cPortProtocolCharAccessProtcolMask
as defined in the following table:
TsPortLinkState | TsPortFixedCfg | TsPortDuplex equivalent to:
| |
down | auto | CPortProtocolCharAccess
| | ProtocolMask = X'0003'
| |
down | fixed | CPortProtocolCharAccess
| | ProtocolMask = X'0001' or
| | = X'0002'
| |
up | auto | cPortProtocolCharCurrent
| | AccessProtocol
| |
up | fixed | cPortProtocolCharCurrent
| | AccessProtocol.rw Enumeration .1.3.6.1.4.1.9.1.111.1.2.2.1.1.21 |
cat2600TsPortCfgLossNumber of events as described in TsPortCfgLossRC
after the port has completed the join process and
then lost communication.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.2.1.1.22 |
cat2600TsPortCfgLossRCReason code describing the cause of configuration loss.ro Enumeration .1.3.6.1.4.1.9.1.111.1.2.2.1.1.23 |
cat2600TsPortCRCCountNumber of frames received with CRC error.
This object is equivalent to dot5StatsLineError and to the
dtrMac MIB object txiStatsLineErrorCounter.ro Counter .1.3.6.1.4.1.9.1.111.1.2.2.1.1.24 |
cat2600TsPortHPChannelFramesNumber of frames sent to the high priority channel
of the particular Token-Ring port.ro Counter .1.3.6.1.4.1.9.1.111.1.2.2.1.1.25 |
cat2600TsPortLPChannelFramesNumber of frames sent to the low priority channel
of the particular Token-Ring port.ro Counter .1.3.6.1.4.1.9.1.111.1.2.2.1.1.26 |
cat2600TsPortHPThresholdPriority level at which frames are sent to the High
priority channel.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.2.1.1.27 |
cat2600TsPortCfgRingSpeedWhen read this object indicates the Port Ring Speed
obtained by the RSA function.
Write to this object when defining the Port Ring Speed
for a fixed configuration (TsPortCfgRSA set to fixed(2)).
When TsPortCfgRSA indicates fixed(2), this object is
equivalent to the dtrMac MIB object
cPortProtocolCharMediumRateOption and to dot5RingSpeed.
Note that the syntax of these objects is different.
For cPortProtocolCharMediumRateOption 1 indicates 4 Mb/s,
while for TsPortCfgRingSpeed 1 indicates 16Mb/s.
This object is a valid read object any time that
TSPortLinkState indicates up(1)or when TsPortCfgRSA
indicates fixed(2).rw Enumeration .1.3.6.1.4.1.9.1.111.1.2.2.1.1.28 |
cat2600TsPortCfgRSAUser configured Ring Speed Adjust or fixed speed.rw Enumeration .1.3.6.1.4.1.9.1.111.1.2.2.1.1.29 |
cat2600TsPortDomainDomain that the port belongs to.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.2.1.1.30 |
cat2600TsPortCfgLossThresholdNumber of configuration loss events (described in
TsPortCfgLossRC) during the sample period which, if
exceeded, should cause the port to be disabled. If the
port is disabled by this function the port must be
manually re-enabled.rw INTEGER .1.3.6.1.4.1.9.1.111.1.2.2.1.1.31 |
cat2600TsPortCfgLossSamplingPeriodThe sampling period, in minutes, for which the port
monitors to see if the configuration loss threshold has
been exceeeded.rw INTEGER .1.3.6.1.4.1.9.1.111.1.2.2.1.1.32 |
cat2600TsPortBeaconStationAddressMAC address of the Station last generating a beacon MAC frame.
This information is present for the generation of a trap and
should not be used to represent the health of the ring. MacAddr .1.3.6.1.4.1.9.1.111.1.2.2.1.1.33 |
cat2600TsPortBeaconNAUNMAC address of the NAUN station last generating a beacon MAC frame.
This information is present for the generation of a trap and
should not be used to represent the health of the ring. MacAddr .1.3.6.1.4.1.9.1.111.1.2.2.1.1.34 |
cat2600TsPortBeaconTypeThe type of Beacon which last occurred. Values are the same
as for the Beacon Type subvector and are defined as follows:
X'0001' Issued by a Dual Ring Station during reconfiguration
X'0002' Signal Loss
X'0003' Timer TCT expired during claim token; no claim token
frames recieved
X'0004' Timer TCT expired during claim token; claim token
frames recieved
X'0005' TXI Access Protocol; Heart Beat Protocol Failure INTEGER .1.3.6.1.4.1.9.1.111.1.2.2.1.1.35 |
cat2600TsOptPortStaTableA table of station addresses known at an
individual port. This table is designed to reduce
the number of SNMP GETNEXT requests. This is done
by packing many values into an octet string. (The
maximum size frame should be used to return the
result.) The instance returned for a GETNEXT is
the value that identifies the last 'row' in the
octet string. When the table is completely
retrieved with one or more GETNEXTs, duplicate
entries may be present, and entries may be skipped
if the table is changing while being retrieved. SEQUENCE OF Cat2600TsOptPortStaEntry .1.3.6.1.4.1.9.1.111.1.2.2.2 |
cat2600TsOptPortStaEntryDefinition of the rows in the optimized port
station address table. Rows can not be created or
deleted via SNMP requests. Cat2600TsOptPortStaEntry .1.3.6.1.4.1.9.1.111.1.2.2.2.1 |
cat2600TsOptPortStaPosSecond index for items in the optimized port
station address table.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.2.2.1.1 |
cat2600TsOptPortStaValAn OCTET STRING containing a multiple number of
stations from a port station address table. Each entry
is encoded in the following format:
Station MAC address - 6 octets
Location 1 - local
2 - remote - 1 octet
Port of exit Mask - 4 octets
Source Frame Count - 4 octets (integer in little endian)
Destn Frame Count - 4 octets (integer in little endian)
Source Byte Count - 4 octets (integer in little endian)
Destn Byte Count - 4 octets (integer in little endian)
The Port of exit mask is encoded in its raw form as stored
in the switch.
Octet 1
Bit position 7 6 5 4 3 2 1 0
Port Number 31 30 29 28 27 26 25 24
Octet 2
Bit position 7 6 5 4 3 2 1 0
Port Number 23 22 21 20 19 18 17 16
Octet 3
Bit position 7 6 5 4 3 2 1 0
Port Number 15 14 13 12 11 10 9 8
Octet 4
Bit position 7 6 5 4 3 2 1 0
Port Number 7 6 5 4 3 2 1 CPUro OCTET STRING .1.3.6.1.4.1.9.1.111.1.2.2.2.1.2 |
cat2600TsPortStnTablePort station table. SEQUENCE OF Cat2600TsPortStnEntry .1.3.6.1.4.1.9.1.111.1.2.2.3 |
cat2600TsPortStnEntryDefinition of rows in the port table. The number
of rows is determined by the hardware and is
specified by the value of cat2600TsNumPorts. Rows can
not be created or deleted via SNMP requests. Cat2600TsPortStnEntry .1.3.6.1.4.1.9.1.111.1.2.2.3.1 |
cat2600TsPortStnPortNumPort number corresponding to this entry.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.2.3.1.1 |
cat2600TsPortStnAddressStation MAC address. Equivalent to ifPhysAddr for this port.ro MacAddr .1.3.6.1.4.1.9.1.111.1.2.2.3.1.2 |
cat2600TsPortStnLocationWhere the station is located.ro Enumeration .1.3.6.1.4.1.9.1.111.1.2.2.3.1.3 |
cat2600TsPortStnSrcFramesNumber of frames with this station as the source.ro Counter .1.3.6.1.4.1.9.1.111.1.2.2.3.1.4 |
cat2600TsPortStnSrcBytesNumber of Bytes with this station as the source.ro Counter .1.3.6.1.4.1.9.1.111.1.2.2.3.1.5 |
cat2600TsPortStnDestnFramesNumber of frames with this station as the destination.ro Counter .1.3.6.1.4.1.9.1.111.1.2.2.3.1.6 |
cat2600TsPortStnDestnBytesNumber of bytes with this station as the destination.ro Counter .1.3.6.1.4.1.9.1.111.1.2.2.3.1.7 |
cat2600TsDmns OBJECT IDENTIFIER .1.3.6.1.4.1.9.1.111.1.2.3 |
cat2600TsDmnTableCurrently active domains on the switch. SEQUENCE OF Cat2600TsDmnEntry .1.3.6.1.4.1.9.1.111.1.2.3.1 |
cat2600TsDmnEntryDefinition of each row in the domain Table Cat2600TsDmnEntry .1.3.6.1.4.1.9.1.111.1.2.3.1.1 |
cat2600TsDmnIndexDomain number for each row.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.3.1.1.1 |
cat2600TsDmnPortsThe set of ports that belong to this Domain.
Each octet within the value of this object specifies
a set of eight ports, with the first octet specifying
ports 1 through 8, the second octet specifying ports 9
through 16, etc. Within each octet, the most
significant bit represents the lowest numbered
port, and the least significant bit represents the
highest numbered port. Thus, each port of the
TokenRing Switch is represented by a single bit within the
value of this object. If that bit has a value of
'1' then that port is included in the set of
ports; the port is not included if its bit has a
value of '0'. Warning: You will not receive a set-
complete message as a set to this object causes the
ports to reset.rw OCTET STRING .1.3.6.1.4.1.9.1.111.1.2.3.1.1.2 |
cat2600TsDmnIpStateIP configuration method for this domain.rw Enumeration .1.3.6.1.4.1.9.1.111.1.2.3.1.1.3 |
cat2600TsDmnIpAddressThe IP Address of this Domain. Changes to this
object will take effect immediately.rw IpAddress .1.3.6.1.4.1.9.1.111.1.2.3.1.1.4 |
cat2600TsDmnIpSubnetMaskThe subnet mask for this domain. Changes to this object
will take effect immediately.rw IpAddress .1.3.6.1.4.1.9.1.111.1.2.3.1.1.5 |
cat2600TsDmnIpDefaultGatewayThe IP Address of the default gateway for this Domain.
Changes to this object will take effect immediately.rw IpAddress .1.3.6.1.4.1.9.1.111.1.2.3.1.1.6 |
cat2600TsDmnStpTurn Spanning tree on or off. Changes to this object will
take effect immediately. The Spanning Tree Objects
themselves are in the dtrConc MIB.rw Enumeration .1.3.6.1.4.1.9.1.111.1.2.3.1.1.7 |
cat2600TsDmnNameUser assigned name for each domain.rw DisplayString .1.3.6.1.4.1.9.1.111.1.2.3.1.1.8 |
cat2600TsDmnIfIndexThe ifIndex of the interface entry corresponding
to each configured domain.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.3.1.1.9 |
cat2600TsDmnBaseBridgeAddrBase MAC address of this domain. Internally equivalent
to dtrCRFMacAddress and to ifPhysAddress of the 'Domain' port.ro MacAddr .1.3.6.1.4.1.9.1.111.1.2.3.1.1.10 |
cat2600TsDmnNumStationsAggregate number of currently active stations
(nodes) on all ports in the domain.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.3.1.1.11 |
cat2600TsDmnMostStationsHighest aggregate number of stations ever active
on all ports at one time, since the last reset or
power cycle.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.3.1.1.12 |
cat2600TsDmnStationTableStations seen in each domain. SEQUENCE OF Cat2600TsDmnStationEntry .1.3.6.1.4.1.9.1.111.1.2.3.5 |
cat2600TsDmnStationEntryDefinition of each row in the domain specific station table.
The object is equivalent to dtrFdbDynamicAddrTable or
dtrFdbStaticAddrTable depending if the entry is learned
or is a configured filter. Cat2600TsDmnStationEntry .1.3.6.1.4.1.9.1.111.1.2.3.5.1 |
cat2600TsDmnStationDmnIndexInteger reference to the domain number in the domain table.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.3.5.1.1 |
cat2600TsDmnStationAddressThe Station's MAC address.ro OCTET STRING .1.3.6.1.4.1.9.1.111.1.2.3.5.1.2 |
cat2600TsDmnStationPortThe source port for the Station. The dtrConc MIB equivalents
are dtrFdbDynamicAddrPortNumber and dtrFdbStaticAddrPortNumber.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.3.5.1.3 |
cat2600TsDmnStationTrafficA bit string that identifies the ports that this station
has generated traffic to or from. The bits correspond to ports,
with bits and ports numbered from right to left so that
bit 0 represents the CPU, bit 1 represents port 1, and so forth.
For example, the returned string 01 4D can be expanded to:
00000001 01001101 binary representation of object string
xxxxxxx8 7654321C ports corresponding to bits
This indicates ports 8, 6, 3, 2 and the CPU. The size
of this string is adjusted to include all ports with traffic.ro OCTET STRING .1.3.6.1.4.1.9.1.111.1.2.3.5.1.4 |
cat2600TsOptDmnStaTableA table of station addresses known at an
individual port. This table is designed to reduce
the number of SNMP GETNEXT requests. This is done
by packing many values into an octet string. (The
maximum size frame should be used to return the
result.) The instance returned for a GETNEXT is
the value that identifies the last 'row' in the
octet string. When the table is completely
retrieved with one or more GETNEXTs, duplicate
entries may be present, and entries may be skipped
if the table is changing while being retrieved. SEQUENCE OF Cat2600TsOptDmnStaEntry .1.3.6.1.4.1.9.1.111.1.2.3.6 |
cat2600TsOptDmnStaEntryDefinition of the rows in the optimized domain
station address table. Rows can not be created or
deleted via SNMP requests. Cat2600TsOptDmnStaEntry .1.3.6.1.4.1.9.1.111.1.2.3.6.1 |
cat2600TsOptDmnStaPosSecond index for items in the optimized port
station address table.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.3.6.1.1 |
cat2600TsOptDmnStaValAn OCTET STRING containing a multiple number of
stations from the domain station address table. Each entry
is encoded in the following format:
Station MAC address - 6 octets
Port of Entry - 1 octet
Traffic Mask - 4 octets
The traffic mask is encoded in its raw form as stored
in the switch.
Octet 1
Bit position 7 6 5 4 3 2 1 0
Port Number 31 30 29 28 27 26 25 24
Octet 2
Bit position 7 6 5 4 3 2 1 0
Port Number 23 22 21 20 19 18 17 16
Octet 3
Bit position 7 6 5 4 3 2 1 0
Port Number 15 14 13 12 11 10 9 8
Octet 4
Bit position 7 6 5 4 3 2 1 0
Port Number 7 6 5 4 3 2 1 CPUro OCTET STRING .1.3.6.1.4.1.9.1.111.1.2.3.6.1.2 |
cat2600TsPipe OBJECT IDENTIFIER .1.3.6.1.4.1.9.1.111.1.2.4 |
cat2600TsPipeTableThe TokenPipe table. SEQUENCE OF Cat2600TsPipeEntry .1.3.6.1.4.1.9.1.111.1.2.4.1 |
cat2600TsPipeEntryDefinition of each row in the TokenPipe table. Cat2600TsPipeEntry .1.3.6.1.4.1.9.1.111.1.2.4.1.1 |
cat2600TsPipeNumberThe TokenPipe number for this row.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.4.1.1.1 |
cat2600TsPipePortsThe set of ports in this switch which are active in this
Pipe. Each octet within the value of this object
specifies a set of eight ports, with the first octet
specifying ports 1 through 8, the second octet specifying
ports 9 through 16 (if available), etc. Within each octet,
the most significant bit represents the lowest numbered
port, and the least significant bit represents the
highest numbered port. Thus, each port of the
NWays LAN Switch is represented by a single bit within the
value of this object. If that bit has a value of
'1' then that port is included in the set of
ports; the port is not included if its bit has a
value of '0'.rw OCTET STRING .1.3.6.1.4.1.9.1.111.1.2.4.1.1.2 |
cat2600TsFilter OBJECT IDENTIFIER .1.3.6.1.4.1.9.1.111.1.2.5 |
cat2600TsFilterTableFilters set up in the switch. SEQUENCE OF Cat2600TsFilterEntry .1.3.6.1.4.1.9.1.111.1.2.5.1 |
cat2600TsFilterEntryDefinition of each row in the filter table. Cat2600TsFilterEntry .1.3.6.1.4.1.9.1.111.1.2.5.1.1 |
cat2600TsFilterStationAddressThe MAC address in a frame to which
this entry's filtering information applies.ro MacAddr .1.3.6.1.4.1.9.1.111.1.2.5.1.1.1 |
cat2600TsFilterTypeThere are two types of filters
(i) source filters which act on the source address
portion of a packet and
(ii) destination filters which act on the destination
address portion of a packet.ro Enumeration .1.3.6.1.4.1.9.1.111.1.2.5.1.1.2 |
cat2600TsFilterStatusThis object indicates the status of this entry.
valid(1) - this entry is currently in use
and will remain so after the next reset
of the bridge.
invalid(2) - writing this value to the object
removes the corresponding entry.rw Enumeration .1.3.6.1.4.1.9.1.111.1.2.5.1.1.3 |
cat2600TsFilterPortsThe set of ports to which this filter is applied.
Each octet within the value of this object specifies
a set of eight ports, with the first octet specifying
ports 1 through 8, the second octet specifying ports 9
through 16, etc. Within each octet, the most
significant bit represents the lowest numbered
port, and the least significant bit represents the
highest numbered port. Thus, each port of the
TokenRing Switch is represented by a single bit within the
value of this object. If that bit has a value of
'1' then that port is included in the set of
ports; the port is not included if its bit has a
value of '0'.
All frames with destination address equal to the
station address corresponding to this entry and
entering from any of the specified ports will be
dropped.
Setting this object with a MIB instance corresponding
to the dotted decimal MAC address and a filter type,
with the set value equal to the mask of ports you
want to filter will create an entry in the table.
Ex. MIB instance: 16.0.90.3.0.36.1
SNMP set value: 7F 00 00 00
This would create a filter entry with the following
characteristics:
MAC Address: 10 00 5A 03 00 24 (canonical format)
Filter Type: source-filter
Filter Ports: 2 3 4 5 6 7 8rw OCTET STRING .1.3.6.1.4.1.9.1.111.1.2.5.1.1.4 |
cat2600TsFilterMaskThe filter mask for this station. The semantics of the
filter mask depend on the type of filter. For a source
filter, the mask gives the ports that are allowed to
receive frames from the filtered address. For a destination
filter, the mask gives the ports that are forced to receive
frames destined to the filtered address.
Each octet within the value of this object specifies
a set of eight ports, with the first octet specifying
ports 1 through 8, the second octet specifying ports 9
through 16 (if available), etc. Within each octet, the most
significant bit represents the lowest numbered
port, and the least significant bit represents the
highest numbered port. Thus, each port of the
switch is represented by a single bit within the
value of this object. If that bit has a value of
'1' then that port is included in the set of
ports; the port is not included if its bit has a
value of '0'.rw OCTET STRING .1.3.6.1.4.1.9.1.111.1.2.5.1.1.5 |
cat2600TsUFC OBJECT IDENTIFIER .1.3.6.1.4.1.9.1.111.1.2.6 |
cat2600TsUFCTableA table of the installed UFC cards in the switch. The number
of entries in the table is given by cat2600TsNumberofUFCs. SEQUENCE OF Cat2600TsUFCEntry .1.3.6.1.4.1.9.1.111.1.2.6.1 |
cat2600TsUFCEntryThe objects contained in the UFC table. Cat2600TsUFCEntry .1.3.6.1.4.1.9.1.111.1.2.6.1.1 |
cat2600TsUFCSlotNumThe number of the slot in which the UFC is installed.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.6.1.1.1 |
cat2600TsUFCNumPhysIfsThe total number of physical network interfaces on the UFC.
This count does not include the interface _OF_ the card or
any logical interfaces which be _ON_ the card.ro INTEGER .1.3.6.1.4.1.9.1.111.1.2.6.1.1.2 |
cat2600TsUFCManufacturerFirmware manufacturer.ro DisplayString .1.3.6.1.4.1.9.1.111.1.2.6.1.1.3 |
cat2600TsUFCTypeThe code representing what type of UFC is present. UFC
codes are assigned by Cisco.ro OCTET STRING .1.3.6.1.4.1.9.1.111.1.2.6.1.1.4 |
cat2600TsUFCTypeDescA text string describing what type of UFC is present.ro DisplayString .1.3.6.1.4.1.9.1.111.1.2.6.1.1.5 |
cat2600TsUFCHwVerThe hardware version in the form major.minor.ro DisplayString .1.3.6.1.4.1.9.1.111.1.2.6.1.1.6 |
cat2600TsUFCFwVerThe firmware version in the form major.minor.ro DisplayString .1.3.6.1.4.1.9.1.111.1.2.6.1.1.7 |
cat2600TsUFCStatusThe operational status of the UFC.ro Enumeration .1.3.6.1.4.1.9.1.111.1.2.6.1.1.8 |
cat2600TsUFCResetThe object is used to reset a UFC. Writing a softReset(3)
causes the switch to reset the hardware, run the minimum
number of diagnostics, and clear all counters. Writing
hardReset(2) causes the UFC to run power up diagnostics and
then execute a softreset.rw Enumeration .1.3.6.1.4.1.9.1.111.1.2.6.1.1.9 |
dtrMIBs OBJECT IDENTIFIER .1.3.6.1.4.1.9.1.111.1.3 |
dtrConcMIB OBJECT IDENTIFIER .1.3.6.1.4.1.9.1.111.1.3.1 |
dtrMacMIB OBJECT IDENTIFIER .1.3.6.1.4.1.9.1.111.1.3.2 |