CADANT-CMTS-PCMM-MIB
The CADANT-CADANT-CMTS-PCMM-MIB enables management of PacketCable Multimedia (PCMM) policy control sessions on Cisco (formerly Cisco PacketCable) CMTS hardware by exposing objects for COPS protocol interactions specific to multimedia service provisioning. It facilitates monitoring of PCMM session states, policy rule enforcement, and resource reservation parameters required for QoS differentiation in cable modem networks.
Imported Objects
Objects
7 total| Object Name |
|---|
cadPCMMMibThis MIB Module supplies the management objects which are
specific to the PacketCable Multimedia client of COPS. The
objects for the management of the standard COPS protocol
reside in RFC2940. MODULE-IDENTITY .1.3.6.1.4.1.4998.1.1.115.1.3 |
cadPCMMMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4998.1.1.115.1.3.1 |
cadPCMMConfigBase OBJECT IDENTIFIER .1.3.6.1.4.1.4998.1.1.115.1.3.1.1 |
cadPCMMAdminStateThe administrative state of PacketCable Multimedia
services on the CMTS.rw AdminState (CADANT-TC) .1.3.6.1.4.1.4998.1.1.115.1.3.1.1.1 |
cadPCMMTimerT1Timer T1 limits the amount of time the Gate authorization
remains valid without a resource reservaton.rw Unsigned32 .1.3.6.1.4.1.4998.1.1.115.1.3.1.1.2 |
cadPCMMCopsVersionThis object describes the PCMM COPS version that the C4 will
advertise in the OPN message.rw CopsVersion .1.3.6.1.4.1.4998.1.1.115.1.3.1.1.3 |
cadPCMMSubscriberIdVrfNameThe name of the virtual router (VRF) that will be used to determine
where a subscriberID remotely connected is located. If the specified
VRF does not exist, then the default VRF will be used instead.rw DisplayString .1.3.6.1.4.1.4998.1.1.115.1.3.1.1.4 |
More MIBs from Arris International
Browse all Arris InternationalMIBs →The ARRIS-D5-VIDEO-MIB provides SNMP management interfaces for monitoring and controlling MPEG video transport streams and associated software processes on Arris DOCSIS 3.0/3.1 Cable Modem Termination Systems (CMTS). It exposes operational metrics for video channel status, stream health, and MPEG protocol state transitions to ensure reliable multicast video delivery over the cable network.
The CADANT-CMTS-SYSTEM-MIB provides management access to Arris E6000 Cable Modem Termination System (CMTS) hardware parameters and system constants, enabling the monitoring of critical device states such as CPU utilization, memory usage, temperature sensors, and interface operational status. This module facilitates the collection of system-level telemetry required for capacity planning, fault isolation, and performance analysis within DOCSIS-based cable networks.
The CADANT-CMTS-MAC-MIB provides vendor-specific extensions for Cadant CMTS hardware to map DOCSIF-MIB CM status indices to MAC address tables, enabling precise tracking of cable modem registration states, signal quality metrics, and interface bindings. This module facilitates granular troubleshooting of subscriber connectivity by correlating physical MAC addresses with logical DOCSIS session parameters on the upstream and downstream channels.
The ARRIS-CER-VIDEO-MIB provides SNMP management capabilities for monitoring and controlling MPEG video software processes and parameters on Arris Cable Edge Router (CER) platforms. It enables the tracking of video session states, stream quality metrics, and encoder/decoder operational status to ensure reliable content delivery.
The CADANT-CMTS-EQUIPMENT-MIB facilitates the remote provisioning, diagnostic testing, and auditing configuration of Arris E6 Cable Modem Termination System (CMTS) hardware, specifically managing card and port states while handling equipment-related trap notifications.
The CADANT-HW-MEAS-MIB aggregates hardware-specific counter metrics for the ARRIS C4 Cable Modem Termination System (CMTS), including standard hardware statistics grouped for engineering analysis. This module facilitates the monitoring of physical device health and resource utilization within the Cadant-managed C4 platform.