ATSWTCH2-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
198
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
198 total| Object Name |
|---|
alliedTelesyn OBJECT IDENTIFIER .1.3.6.1.4.1.207 |
RFC-1215 Unknown .1.3.6.1.4.1.207 |
newRootThe newRoot trap indicates that the sending agent
has become the new root of the Spanning Tree; the
trap is sent by a bridge soon after its election
as the new root, e.g., upon expiration of the
Topology Change Timer immediately subsequent to
its election. Implementation of this trap is
optional. TRAP-TYPE .1.3.6.1.4.1.207.0.101 |
topologyChangeA topologyChange trap is sent by a bridge when
any of its configured ports transitions from the
Learning state to the Forwarding state, or from
the Forwarding state to the Blocking state. The
trap is not sent if a newRoot trap is sent for the
same transition. Implementation of this trap is
optional. TRAP-TYPE .1.3.6.1.4.1.207.0.102 |
intruderTrapThe intruderTrap trap indicates that there was a Intruder
was detected on the port shown as ifIndex. TRAP-TYPE .1.3.6.1.4.1.207.0.105 |
atiProduct OBJECT IDENTIFIER .1.3.6.1.4.1.207.1 |
mibObject OBJECT IDENTIFIER .1.3.6.1.4.1.207.8 |
atswitchMib OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10 |
atswitchSysGroup OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.1 |
atswitchProductTypeThis object will return Product Type.ro Enumeration .1.3.6.1.4.1.207.8.10.1.1 |
atswitchEthernetPortCountThis object will return the number of 10/100 Mbps Ethernet ports
on the switch.ro INTEGER .1.3.6.1.4.1.207.8.10.1.2 |
atswitchResetSetting this object to 'switch-reset' will
cause the switch to perform a hardware reset
within approximately 4-6 seconds.
Setting this object to 'switch-no-reset will
have no effect.
The value 'no-reset' will be returned whenever
this object is retrieved.rw Enumeration .1.3.6.1.4.1.207.8.10.1.3 |
atswitchMDA1TypeThis object returns the MDA type of the Uplink portro Enumeration .1.3.6.1.4.1.207.8.10.1.4 |
atswitchMDA2TypeThis Object is supported in 81XX product line
only.
This object returns the MDA type of the Uplink Port
named 'B'. It returns 'none' if a 'B' MDA slot
is not installed.ro Enumeration .1.3.6.1.4.1.207.8.10.1.5 |
atswitchDeviceFlowControlThis Object is supported on 81XX products only.
This object configures the Flow Control of the Devicerw Enumeration .1.3.6.1.4.1.207.8.10.1.6 |
atswitchSwGroup OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.1.7 |
atswitchSwProductIdentifies the software product the device is running.ro DisplayString .1.3.6.1.4.1.207.8.10.1.7.1 |
atswitchSwVersionIdentifies the version number of the present release.ro DisplayString .1.3.6.1.4.1.207.8.10.1.7.2 |
atswitchIpGroup OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.1.8 |
atswitchCurrentIpAddressThe Current IP address is the one which is currently used
and is obtained dynamically through one of the protocols
interaction.( DHCP or Bootp.)
This address is NULL if the Address is Statically configured.ro IpAddress .1.3.6.1.4.1.207.8.10.1.8.1 |
atswitchConfiguredIpAddressThe Configured IP address of the device. This is the address
configured through Network or Local Omega.rw IpAddress .1.3.6.1.4.1.207.8.10.1.8.2 |
atswitchConfiguredSubnetMaskThe Configured Subnet Mask of the device.rw IpAddress .1.3.6.1.4.1.207.8.10.1.8.3 |
atswitchConfiguredRouterThe Configured Gateway/Router address of the devicerw IpAddress .1.3.6.1.4.1.207.8.10.1.8.4 |
atswitchIPAddressStatusThe IP Address can be obtained/configured by any of the above
different ways. This object specifies how IP address currently
on the switch Box, was configured/obtained.ro Enumeration .1.3.6.1.4.1.207.8.10.1.8.5 |
atswitchDNServerThe Configured DNS Server address of the devicerw IpAddress .1.3.6.1.4.1.207.8.10.1.8.6 |
atswitchDefaultDomainNameThis Object defines the Default Domain where this switch can be
belong to.rw DisplayString .1.3.6.1.4.1.207.8.10.1.8.7 |
atswitchNMGroup OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.1.9 |
atswitchNwMgrTableA list of SNMP Trap Manager stations Entries.
The number of entries is given by the
switchNwMgrTotal mib object. SEQUENCE OF AtswitchNwMgrEntry .1.3.6.1.4.1.207.8.10.1.9.1 |
atswitchNwMgrEntryTrap receipt Manager Entry containing ipaddress of
the configured NMS's to which Traps are sent. AtswitchNwMgrEntry .1.3.6.1.4.1.207.8.10.1.9.1.1 |
atswitchNwMgrIndexThe Index of the Managers Ip address.ro INTEGER .1.3.6.1.4.1.207.8.10.1.9.1.1.1 |
atswitchNwMgrIpAddrThe IP Address of the NMS host configured.rw IpAddress .1.3.6.1.4.1.207.8.10.1.9.1.1.2 |
atswitchConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.2 |
atswitchPortDisableOnSecurityViolationThis System wide attribute allows the port to be disabled on
Violation of the Security. or suspend the port due to Duplicate Address.
Needs More explaination after somebody figures out whether atswitch
needs the suspend state.rw Enumeration .1.3.6.1.4.1.207.8.10.2.1 |
atswitchMirroringSourcePortThis is the Source port number for which there is another
mirror port.If the atswitchEthConfigMirrorState is Enabled then
,the mirror portgets routed with all the packets going in and
out of Source port. This arrangement is to put an RMON Probe
on mirrored port to Probe the traffic on the Source
port. One of the port is dedicated to this so that for
any port as source port, this dedicated port can be a mirrored
port.
This object will return a '0' if the MirrorState is not
enabled.
For the AT-81XX only the receive activity can be mirrored.rw INTEGER .1.3.6.1.4.1.207.8.10.2.2 |
atswitchMirrorStateif the state of Mirroring is enabled by selecting one of the
first three values , then the Mirroring explained above works.
If disabled, port operation works normally. No Traffic
gets routed from MirroringSourcePort to Destination Mirrored Port.
Mirroring of both transmit and receive activity can only be
done if the port is half duplex. Choose both only if you know
the port will be run in half duplex mode.rw Enumeration .1.3.6.1.4.1.207.8.10.2.3 |
atswitchMirroringDestinationPortThis is the Destination port number for which there is another
mirror port.If the atswitchEthConfigMirrorState is Enabled then
,the mirror portgets routed with all the packets going in and
out of Destination port. This arrangement is to put an RMON Probe
on mirrored port to Probe the traffic on the Destination
port. One of the port is dedicated to this so that for
any port as destination port, this dedicated port can be a mirrored
port.
This object will return a '0' if the MirrorState is not
enabled.
For the AT-81XX only the receive activity can be mirrored.rw INTEGER .1.3.6.1.4.1.207.8.10.2.4 |
atswitchSecurityConfigThis Object is suppported only in 37XX product Line.
Security feature configuration Object.
The Security disable would let the device carry on the
learn-new-address-as-it-comes-in mode as usual.
When security is enabled-with-learning-locked, the learning of
new address is stopped and the addresses locked in the device is
used as the security Database. If an address comes in which is
not present in the Device Security Database, then any of the
atswitchSecurityAction Configured is triggered.
When limited-enabled is selected, a per-port
atswitchPortSecurityNumberOfAddresses specify the max number
of MACs to be learned .rw Enumeration .1.3.6.1.4.1.207.8.10.2.5 |
atswitchSecurityActionSecurity Action to be carried when the atswitchSecurityConfig is
enabled-with-learning-locked or limted-enabled.rw Enumeration .1.3.6.1.4.1.207.8.10.2.6 |
atswitchDebugAvailableBytesThis is strictly for Debug reason and this object should not be
beleived as the correct numberro INTEGER .1.3.6.1.4.1.207.8.10.2.7 |
atswitchTrunkConfigThis Object Configures the Trunking for the Uplink Ports only.
This feature is currently available only in Fenix 37XX-XL
hardware.rw Enumeration .1.3.6.1.4.1.207.8.10.2.8 |
atswitchPortConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.3 |
atswitchPortTableTable of basic port configuration information. SEQUENCE OF AtswitchPortEntry .1.3.6.1.4.1.207.8.10.3.1 |
atswitchPortEntryAn entry in the port config table. AtswitchPortEntry .1.3.6.1.4.1.207.8.10.3.1.1 |
atswitchPortNumberThis object identifies the port of the switch.ro INTEGER .1.3.6.1.4.1.207.8.10.3.1.1.1 |
atswitchPortNameThis attribute associates a user defined string name
with the port.rw DisplayString .1.3.6.1.4.1.207.8.10.3.1.1.2 |
atswitchPortAutosenseOrHalfDuplexThis attribute allows an administrative request to
configure whether this port can Autosense or Force the Half Duplexrw Enumeration .1.3.6.1.4.1.207.8.10.3.1.1.3 |
atswitchPortLinkStateThis attribute allows an administrative request to
read the status of link state on this port.ro Enumeration .1.3.6.1.4.1.207.8.10.3.1.1.4 |
atswitchPortDuplexStatusThis attribute allows an administrative request to
read the status of Duplex on this port.ro Enumeration .1.3.6.1.4.1.207.8.10.3.1.1.5 |
atswitchPortSpeedThis attribute allows an administrative request to
read/write the speed of this port.
This attribure is read-only for all the Ports on
AT-37XX product .
This Attribute is read-write for ATS21 (AT81XX) product
Only. This attribute allows an administrative request to
change the speed on ATS21 product.rw Enumeration .1.3.6.1.4.1.207.8.10.3.1.1.6 |
atswitchPortStateThis attribute allows an administrative request to
disable or enable communications on this port.It also
responds with the status of the port .Except enabled(1) and
disabled(2), all values are read-only status.rw Enumeration .1.3.6.1.4.1.207.8.10.3.1.1.7 |
atswitchPortTransmitPacingConfigThis Object is supported on AT36XX product line Only.
This attribute allows the transmit Pacing to be enabled or
disabled.rw Enumeration .1.3.6.1.4.1.207.8.10.3.1.1.8 |
atswitchPortSTPConfigThis attribute allows a bridging Mode to be configured with
either Spanning Tree enabled or disabled. When Spanning tree is
enabled, make sure that this port is belonging to a valid
Bridge_id. Spanning Tree is enabled only when a valid Bridge_id
is set.rw Enumeration .1.3.6.1.4.1.207.8.10.3.1.1.9 |
atswitchPortBridgeidThe Bridge to which this port belongs to .rw INTEGER .1.3.6.1.4.1.207.8.10.3.1.1.10 |
atswitchPortSTPCostThe Cost of the Spanning Tree Protocol.This object is valid only
when STP is enabled.rw INTEGER .1.3.6.1.4.1.207.8.10.3.1.1.11 |
atswitchPortSTPPriorityThe Priority of the spanning Tree Protocol. This object is valid when
STP is enabled.rw INTEGER .1.3.6.1.4.1.207.8.10.3.1.1.12 |
atswitchPortSwitchingTypeThis per-port attribute describes whether the port identified
by atswitchPortNumber uses store-and-forward bridging for local switched
Ethernet packets or cut-through. The Hardware allows cut-through on
Transmission and cut-through-on Receive and the same for the
store-and-forward. But some of the Config option does not make any sense.
So, for now there is no distiction of Rx and Tx. Both Tx/Rx support
store-and-forward or cut-through.
This Object is not applicable for 37XX with XL hardware as the Hardware
does not support both Cut through and Store and Forward. It is default
Store and Forward. Even though the Set on either of them is done, Hardware does
not do the Cut through Switching.rw Enumeration .1.3.6.1.4.1.207.8.10.3.1.1.13 |
atswitchPortFlowControlEnableThis Per_port attribute is only for ATS21 product.(81XX).
This per-port attribute describes whether the port
identified has flow Control Enabled or not. Flow Control
on Full Duplex and Half Duplex is detected and
Automatically, flow control accordingly is taken care of.
BY Default, Flow Control is Disabled.rwdeprecated Enumeration .1.3.6.1.4.1.207.8.10.3.1.1.14 |
atswitchPortSecurityNumberOfAddressesThis object configures the Max number of addresses at an
instance to be learnt by the device. If the learnt addresses
number is above this number, then the atswitchSecurityAction is
triggered . when the number of learnt addresses exceeds this
number ,the the atswitchSecurityAction is triggered only if
atswitchSecurityConfig is set to limited-enalbled. ELse
nothing is triggered.rw INTEGER .1.3.6.1.4.1.207.8.10.3.1.1.15 |
atswitchVlanConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.4 |
atswitchBasicVlanTableTable of Virtual LAN configured. SEQUENCE OF AtswitchBasicVlanEntry .1.3.6.1.4.1.207.8.10.4.1 |
atswitchBasicVlanEntryAn entry in the table, containing VLAN information. AtswitchBasicVlanEntry .1.3.6.1.4.1.207.8.10.4.1.1 |
atswitchBeVlanIndexThis object identifies the VLAN.ro INTEGER .1.3.6.1.4.1.207.8.10.4.1.1.1 |
atswitchBeVlanNameThis attribute associates a user defined string with
the Virtual LAN. To configure a new VLAN, do 'set' operation on
this object with the VLAN name. To delete an VLAN, do 'set'
operation with string '*'.
Before configuring any of the objects in this row , set the
atswitchVlanStatus to 'under-construction' and once configured with all
the information, please set the same object to operationalrw DisplayString .1.3.6.1.4.1.207.8.10.4.1.1.2 |
atswitchBeVlanTagIdThis object is supported by 37xx series of fenix with the
VLAN tagging capability hardware only. Please check whether
the SysObjectId is greater than 29.
This object configures the VId in the Tag Information header
in accordance with 802.1q spec.
Before configuring any of the objects in this row , set the
atswitchVlanStatus to 'under-construction' and once configured with all
the information, please set the same object to operationalrw INTEGER .1.3.6.1.4.1.207.8.10.4.1.1.3 |
atswitchBeVlanPortMaskThis object is supported by 37xx series of fenix with the
VLAN tagging capability hardware only. Please check whether
the SysObjectId is greater than 29.
This Object builds the Output Ports that participate in the
Vlan with the atswitchBeVlanName. The Format of the input string
would be like '1,2,5,7,12'.
Before configuring any of the objects in this row , set the
atswitchVlanStatus to 'under-construction' and once configured
with all the information, please set the same object to
operationalrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.207.8.10.4.1.1.4 |
atswitchBeVlanRowStatusThis object is supported by 37xx series of fenix with the
VLAN tagging capability hardware only. Please check whether
the SysObjectId is greater than 29.
This object identifies the atswitchBeVLANEntry Row Status .
The User sets this object to under-construction, to start with
to create a row.
Once the User Configures the VlanName and TagId and also the
Output Ports.This object should be set to operational.
If the user does not set this object to operational,
the whole row is lost .when a 'get' of this row is
done, this uncommited row is not seen.
configured in the switch.rw Enumeration .1.3.6.1.4.1.207.8.10.4.1.1.5 |
atswitchPort2VlanTableTable of per port Virtual LAN configuration. SEQUENCE OF AtswitchPort2VlanEntry .1.3.6.1.4.1.207.8.10.4.2 |
atswitchPort2VlanEntryAn entry in the table, containing per port VLAN information. AtswitchPort2VlanEntry .1.3.6.1.4.1.207.8.10.4.2.1 |
atswitchPvPortNumberThis object identifies the port on the switch.ro INTEGER .1.3.6.1.4.1.207.8.10.4.2.1.1 |
atswitchPvVlanNameThis attribute associates a user defined string with
the Virtual LAN. This Object is the same as atswitchBeVlanName.
Please make sure to give the same string as atswitchBeVlanName.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.207.8.10.4.2.1.2 |
atswitchEthernetStatsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.5 |
atswitchEthMonStats OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.5.1 |
atswitchEthMonRxGoodFramesThe total number of Good Frames received on this module.ro Counter .1.3.6.1.4.1.207.8.10.5.1.1 |
atswitchEthMonTxGoodFramesThe total number of Good Frames Transmitted by this module.ro Counter .1.3.6.1.4.1.207.8.10.5.1.2 |
atswitchEthMonTxTotalBytesThe total number of Bytes transmitted from this module.ro Counter .1.3.6.1.4.1.207.8.10.5.1.3 |
atswitchEthMonTxDeferredThis is the count of first time Transmission attempt which
failed on an interface due to medium being busy.ro Counter .1.3.6.1.4.1.207.8.10.5.1.4 |
atswitchEthMonTxCollisionsThe total number of collisions while switching on an interface.ro Counter .1.3.6.1.4.1.207.8.10.5.1.5 |
atswitchEthErrorStats OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.5.2 |
atswitchEthErrorCRCThe total number of CRC errors on received packets.ro Counter .1.3.6.1.4.1.207.8.10.5.2.1 |
atswitchEthErrorAlignmentThe total number of packets received that has alignment
errorsro Counter .1.3.6.1.4.1.207.8.10.5.2.2 |
atswitchEthErrorRxBadFramesThe counter is incremented when a bad frame was received.ro Counter .1.3.6.1.4.1.207.8.10.5.2.3 |
atswitchEthErrorLateCollisionsThis object counts the number of times the collison was
detected in the port.ro Counter .1.3.6.1.4.1.207.8.10.5.2.4 |
atswitchEthErrorTxTotalTotal number of error resulted from transfer operations.ro Counter .1.3.6.1.4.1.207.8.10.5.2.6 |
atswitchEthPortStatsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.6 |
atswitchEthPortMonStats OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.6.1 |
atswitchEthPortMonTableA list of statistics entries. SEQUENCE OF AtswitchEthPortMonEntry .1.3.6.1.4.1.207.8.10.6.1.1 |
atswitchEthPortMonEntryA collection of statistics kept for a particular port. AtswitchEthPortMonEntry .1.3.6.1.4.1.207.8.10.6.1.1.1 |
atswitchEthPortMonIdThe relative position of a port within a switch starting with 1.ro INTEGER .1.3.6.1.4.1.207.8.10.6.1.1.1.1 |
atswitchEthPortMonTxTotalBytesThe total number of Bytes transmited to this port.ro Counter .1.3.6.1.4.1.207.8.10.6.1.1.1.2 |
atswitchRxGoodFramesThe total number of good packets(including unicast,broadcast
packets and multicast packets) receivedro Counter .1.3.6.1.4.1.207.8.10.6.1.1.1.3 |
atswitchTxGoodFramesThe total number of good packets(including bad packets,
broadcast packets and multicast packets) transmitted successfullyro Counter .1.3.6.1.4.1.207.8.10.6.1.1.1.4 |
atswitchTxBroadcastFramesThe total number of packets transmitted that were directed to
the broadcast address. This does not include multicast packetsro Counter .1.3.6.1.4.1.207.8.10.6.1.1.1.5 |
atswitchTxMulticastFramesThe total number of packets transmitted that were directed to
a multicast address. This does not include packets addressed to the
broadcast addressro Counter .1.3.6.1.4.1.207.8.10.6.1.1.1.6 |
atswitchAddrDuplicateThe number of address duplications seen on this port which is
secured on another port. If a source address is locked for a port and if
that address is eeen as source address on this port, then such occurances
of duplicate Address is noted.ro Counter .1.3.6.1.4.1.207.8.10.6.1.1.1.7 |
atswitchAddrMismatchesAddress mismatches /address changes
the sum of :
1. The number of mismatches seen on a port between a securely assigned port address and the source address observed on the port.
Occurrence of this causes the TNETX3150 to suspend the port.
2. The number of times the TNETX3150 is required to assign or learn
an address for a port.ro Counter .1.3.6.1.4.1.207.8.10.6.1.1.1.8 |
atswitchRxOverrunsThe number of frames lost due to lack of resources during frame reception. The counter is incremented when frame data cannot enter the RX fifo for whatever reason. Frames that overrun after entering the fifo also can be counted as RX discards if they are not cut-through.ro Counter .1.3.6.1.4.1.207.8.10.6.1.1.1.9 |
atswitchEthPortError OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.6.2 |
atswitchEthPortErrorTableA list of statistics entries. SEQUENCE OF AtswitchEthPortErrorEntry .1.3.6.1.4.1.207.8.10.6.2.1 |
atswitchEthPortErrorEntryA collection of statistics kept for a particular port. AtswitchEthPortErrorEntry .1.3.6.1.4.1.207.8.10.6.2.1.1 |
atswitchEthPortErrorIdThe relative position of a port within a switch starting with 1.ro INTEGER .1.3.6.1.4.1.207.8.10.6.2.1.1.1 |
atswitchEthPortErrorRxBadFramesThe counter is incremented when a bad frame was received
on this port.ro Counter .1.3.6.1.4.1.207.8.10.6.2.1.1.2 |
atswitchEthPortErrorTxTotalTotal number of error resulted from transmit operations
on this port.ro Counter .1.3.6.1.4.1.207.8.10.6.2.1.1.3 |
atswitchFwdVlanGroup OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.7 |
atswitchFwdVlanTableThis tables lists Mac Addresses lexicographically from the forwarding table and also the information about the Vlan/Vlan which this MAC address belongs to. SEQUENCE OF AtswitchFwdVlanEntry .1.3.6.1.4.1.207.8.10.7.1 |
atswitchFwdVlanEntryEntry in the atswitchFwdVlanTable. AtswitchFwdVlanEntry .1.3.6.1.4.1.207.8.10.7.1.1 |
atswitchFwdVlanMACAddrThis object identifies the MAC Address associated
with this entry.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.207.8.10.7.1.1.1 |
atswitchFwdVlanVlanIdThis object identifies the Vlan/Vlan which MAC Address
defined by the atswitchFwdMACAddr is associated with.ro INTEGER .1.3.6.1.4.1.207.8.10.7.1.1.2 |
atswitchFwdVlanAgeCurrent Age of the MACAddr in the Forwarding Table.It Starts
with 0 and if not heard it increments to some value until it
hears from it and if not heard before reaching Max value, it will purge this entry.ro INTEGER .1.3.6.1.4.1.207.8.10.7.1.1.3 |
atswitchFwdVlanStatusThe status of this entry.
The meanings of the values are:
inactive(1) : this entry is not longer valid
(e.g., it was learned but has since
aged-out), but has not yet been
flushed from the table.
active(2) : the value of the corresponding
instance of atswitchFwdVlanPort was
active, and is being used.
other(3) : none of the following.ro Enumeration .1.3.6.1.4.1.207.8.10.7.1.1.4 |
atswitchFwdVlanPortEither the value '0', or the port number of the
port on which a frame having a source address
equal to the value of the corresponding instance
of atswitchFwdVlanMACAddr has been seen. A value of
'0' indicates that the port number has not been
learned but that the bridge does have some
forwarding/filtering information about this
address.
Implementors are encouraged to assign the port
value to this object whenever it is learned even
for addresses for which the corresponding value of
atswitchFwdVlanStatus is not learned(3).ro INTEGER .1.3.6.1.4.1.207.8.10.7.1.1.5 |
atswitchTrapAttrGroup OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.8 |
atswitchDuplicateMacAddressThe Duplicate Mac address which is secured on
atswitchSecurePortNumber. OCTET STRING .1.3.6.1.4.1.207.8.10.8.1 |
atswitchIntruderMacAddressThe Mac address of the Intruder as seen on port which is the
the next object OCTET STRING .1.3.6.1.4.1.207.8.10.8.2 |
atswitchSecuredPortNumberThis is the Port number which has the duplicate Address as the
secured address . INTEGER .1.3.6.1.4.1.207.8.10.8.3 |
atswitchBridgeMib OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.9 |
atswitchBrBase OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.9.1 |
atswitchBrBaseTableTable of basic bridge information. SEQUENCE OF AtswitchBrBaseEntry .1.3.6.1.4.1.207.8.10.9.1.1 |
atswitchBrBaseEntryAn entry in the atswitchBrBaseTable. AtswitchBrBaseEntry .1.3.6.1.4.1.207.8.10.9.1.1.1 |
atswitchBrBaseLanIdThis object uniquely identifies the lan or
Virtual lan.ro INTEGER .1.3.6.1.4.1.207.8.10.9.1.1.1.1 |
atswitchBrBaseBridgeAddressThe MAC address used by this bridge when it must
be referred to in a unique fashion. It is
recommended that this be the numerically smallest
MAC address of all ports that belong to this
bridge. However it is only required to be unique.
When concatenated with atswitchBrStpPriority a unique
BridgeIdentifier is formed which is used in the
Spanning Tree Protocol.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.207.8.10.9.1.1.1.2 |
atswitchBrBaseNumPortsThe number of ports controlled by this bridging
entity.ro INTEGER .1.3.6.1.4.1.207.8.10.9.1.1.1.3 |
atswitchBrBaseTypeIndicates what type of bridging this bridge can
perform. If a bridge is actually performing a
certain type of bridging this will be indicated by
entries in the port table for the given type.ro Enumeration .1.3.6.1.4.1.207.8.10.9.1.1.1.4 |
atswitchBrBasePortTableA table that contains generic information about
every port that is associated with this bridge.
Transparent, source-route, and srt ports are
included. SEQUENCE OF AtswitchBrBasePortEntry .1.3.6.1.4.1.207.8.10.9.1.4 |
atswitchBrBasePortEntryA list of information for each port of the
bridge. AtswitchBrBasePortEntry .1.3.6.1.4.1.207.8.10.9.1.4.1 |
atswitchBrBasePortLanIdThis object uniquely identifies the lan or
Virtual lan.ro INTEGER .1.3.6.1.4.1.207.8.10.9.1.4.1.1 |
atswitchBrBasePortThe port number of the port for which this entry
contains bridge management information.ro INTEGER .1.3.6.1.4.1.207.8.10.9.1.4.1.2 |
atswitchBrBasePortIfIndexThe value of the instance of the ifIndex object,
defined in MIB-II, for the interface corresponding
to this port.ro INTEGER .1.3.6.1.4.1.207.8.10.9.1.4.1.3 |
atswitchBrBasePortCircuitFor a port which (potentially) has the same value
of atswitchBrBasePortIfIndex as another port on the
same bridge, this object contains the name of an
object instance unique to this port. For example,
in the case where multiple ports correspond one-
to-one with multiple X.25 virtual circuits, this
value might identify an (e.g., the first) object
instance associated with the X.25 virtual circuit
corresponding to this port.
For a port which has a unique value of
atswitchBrBasePortIfIndex, this object can have the
value { 0 0 }.ro OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.9.1.4.1.4 |
atswitchBrBasePortDelayExceededDiscardsThe number of frames discarded by this port due
to excessive transit delay through the bridge. It
is incremented by both transparent and source
route bridges.ro Counter .1.3.6.1.4.1.207.8.10.9.1.4.1.5 |
atswitchBrBasePortMtuExceededDiscardsThe number of frames discarded by this port due
to an excessive size. It is incremented by both
transparent and source route bridges.ro Counter .1.3.6.1.4.1.207.8.10.9.1.4.1.6 |
atswitchBrStp OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.9.2 |
atswitchBrStpTableTable of bridge spanning tree information. SEQUENCE OF AtswitchBrStpEntry .1.3.6.1.4.1.207.8.10.9.2.1 |
atswitchBrStpEntryAn entry in the atswitchBrStpTable. AtswitchBrStpEntry .1.3.6.1.4.1.207.8.10.9.2.1.1 |
atswitchBrStpLanIdThis object uniquely identifies the lan or
Virtual lan.ro INTEGER .1.3.6.1.4.1.207.8.10.9.2.1.1.1 |
atswitchBrStpProtocolSpecificationAn indication of what version of the Spanning
Tree Protocol is being run. The value
'decLb100(2)' indicates the DEC LANbridge 100
Spanning Tree protocol. IEEE 802.1d
implementations will return 'ieee8021d(3)'. If
future versions of the IEEE Spanning Tree Protocol
are released that are incompatible with the
current version a new value will be defined.ro Enumeration .1.3.6.1.4.1.207.8.10.9.2.1.1.2 |
atswitchBrStpPriorityThe value of the write-able portion of the Bridge
ID, i.e., the first two octets of the (8 octet
long) Bridge ID. The other (last) 6 octets of the
Bridge ID are given by the value of
atswitchBrBaseBridgeAddress.rw INTEGER .1.3.6.1.4.1.207.8.10.9.2.1.1.3 |
atswitchBrStpTimeSinceTopologyChangeThe time (in hundredths of a second) since the
last time a topology change was detected by the
bridge entity.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.207.8.10.9.2.1.1.4 |
atswitchBrStpTopChangesThe total number of topology changes detected by
this bridge since the management entity was last
reset or initialized.ro Counter .1.3.6.1.4.1.207.8.10.9.2.1.1.5 |
atswitchBrStpDesignatedRootThe bridge identifier of the root of the spanning
tree as determined by the Spanning Tree Protocol
as executed by this node. This value is used as
the Root Identifier parameter in all Configuration
Bridge PDUs originated by this node.ro BridgeId .1.3.6.1.4.1.207.8.10.9.2.1.1.6 |
atswitchBrStpRootCostThe cost of the path to the root as seen from
this bridge.ro INTEGER .1.3.6.1.4.1.207.8.10.9.2.1.1.7 |
atswitchBrStpRootPortThe port number of the port which offers the
lowest cost path from this bridge to the root
bridge.ro INTEGER .1.3.6.1.4.1.207.8.10.9.2.1.1.8 |
atswitchBrStpMaxAgeThe maximum age of Spanning Tree Protocol
information learned from the network on any port
before it is discarded, in units of hundredths of
a second. This is the actual value that this
bridge is currently using.ro Timeout .1.3.6.1.4.1.207.8.10.9.2.1.1.9 |
atswitchBrStpHelloTimeThe amount of time between the transmission of
Configuration bridge PDUs by this node on any port
when it is the root of the spanning tree or trying
to become so, in units of hundredths of a second.
This is the actual value that this bridge is
currently using.ro Timeout .1.3.6.1.4.1.207.8.10.9.2.1.1.10 |
atswitchBrStpHoldTimeThis time value determines the interval length
during which no more than two Configuration bridge
PDUs shall be transmitted by this node, in units
of hundredths of a second.ro INTEGER .1.3.6.1.4.1.207.8.10.9.2.1.1.11 |
atswitchBrStpForwardDelayThis time value, measured in units of hundredths
of a second, controls how fast a port changes its
spanning state when moving towards the Forwarding
state. The value determines how long the port
stays in each of the Listening and Learning
states, which precede the Forwarding state. This
value is also used, when a topology change has
been detected and is underway, to age all dynamic
entries in the Forwarding Database. [Note that
this value is the one that this bridge is
currently using, in contrast to
atswitchBrStpBridgeForwardDelay which is the value that
this bridge and all others would start using
if/when this bridge were to become the root.]ro Timeout .1.3.6.1.4.1.207.8.10.9.2.1.1.12 |
atswitchBrStpBridgeMaxAgeThe value that all bridges use for MaxAge when
this bridge is acting as the root. Note that
802.1D-1990 specifies that the range for this
parameter is related to the value of
atswitchBrStpBridgeHelloTime. The granularity of this
timer is specified by 802.1D-1990 to be 1 second.
An agent may return a badValue error if a set is
attempted to a value which is not a whole number
of seconds.rw Timeout .1.3.6.1.4.1.207.8.10.9.2.1.1.13 |
atswitchBrStpBridgeHelloTimeThe value that all bridges use for HelloTime when
this bridge is acting as the root. The
granularity of this timer is specified by 802.1D-
1990 to be 1 second. An agent may return a
badValue error if a set is attempted to a value
which is not a whole number of seconds.rw Timeout .1.3.6.1.4.1.207.8.10.9.2.1.1.14 |
atswitchBrStpBridgeForwardDelayThe value that all bridges use for ForwardDelay
when this bridge is acting as the root. Note that
802.1D-1990 specifies that the range for this
parameter is related to the value of
atswitchBrStpBridgeMaxAge. The granularity of this
timer is specified by 802.1D-1990 to be 1 second.
An agent may return a badValue error if a set is
attempted to a value which is not a whole number
of seconds.rw Timeout .1.3.6.1.4.1.207.8.10.9.2.1.1.15 |
atswitchBrStpPortTableA table that contains port-specific information
for the Spanning Tree Protocol. SEQUENCE OF AtswitchBrStpPortEntry .1.3.6.1.4.1.207.8.10.9.2.15 |
atswitchBrStpPortEntryA list of information maintained by every port
about the Spanning Tree Protocol state for that
port. AtswitchBrStpPortEntry .1.3.6.1.4.1.207.8.10.9.2.15.1 |
atswitchBrStpPortLanIdThis object uniquely identifies the lan or
Virtual lan.ro INTEGER .1.3.6.1.4.1.207.8.10.9.2.15.1.1 |
atswitchBrStpPortThe port number of the port for which this entry
contains Spanning Tree Protocol management
information.ro INTEGER .1.3.6.1.4.1.207.8.10.9.2.15.1.2 |
atswitchBrStpPortPriorityThe value of the priority field which is
contained in the first (in network byte order)
octet of the (2 octet long) Port ID. The other
octet of the Port ID is given by the value of
atswitchBrStpPort.rw INTEGER .1.3.6.1.4.1.207.8.10.9.2.15.1.3 |
atswitchBrStpPortStateThe port's current state as defined by
application of the Spanning Tree Protocol. This
state controls what action a port takes on
reception of a frame. If the bridge has detected
a port that is malfunctioning it will place that
port into the broken(6) state. For ports which
are disabled (see atswitchBrStpPortEnable), this object
will have a value of disabled(1).ro Enumeration .1.3.6.1.4.1.207.8.10.9.2.15.1.4 |
atswitchBrStpPortEnableThe enabled/disabled status of the port.rw Enumeration .1.3.6.1.4.1.207.8.10.9.2.15.1.5 |
atswitchBrStpPortPathCostThe contribution of this port to the path cost of
paths towards the spanning tree root which include
this port. 802.1D-1990 recommends that the
default value of this parameter be in inverse
proportion to the speed of the attached LAN.rw INTEGER .1.3.6.1.4.1.207.8.10.9.2.15.1.6 |
atswitchBrStpPortDesignatedRootThe unique Bridge Identifier of the Bridge
recorded as the Root in the Configuration BPDUs
transmitted by the Designated Bridge for the
segment to which the port is attached.ro BridgeId .1.3.6.1.4.1.207.8.10.9.2.15.1.7 |
atswitchBrStpPortDesignatedCostThe path cost of the Designated Port of the
segment connected to this port. This value is
compared to the Root Path Cost field in received
bridge PDUs.ro INTEGER .1.3.6.1.4.1.207.8.10.9.2.15.1.8 |
atswitchBrStpPortDesignatedBridgeThe Bridge Identifier of the bridge which this
port considers to be the Designated Bridge for
this port's segment.ro BridgeId .1.3.6.1.4.1.207.8.10.9.2.15.1.9 |
atswitchBrStpPortDesignatedPortThe Port Identifier of the port on the Designated
Bridge for this port's segment.ro OCTET STRING .1.3.6.1.4.1.207.8.10.9.2.15.1.10 |
atswitchBrStpPortForwardTransitionsThe number of times this port has transitioned
from the Learning state to the Forwarding state.ro Counter .1.3.6.1.4.1.207.8.10.9.2.15.1.11 |
atswitchBrTp OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.9.3 |
atswitchBrTpTableTable of transparent bridging information. SEQUENCE OF AtswitchBrTpEntry .1.3.6.1.4.1.207.8.10.9.3.1 |
atswitchBrTpEntryAn entry in the atswitchBrTpTable. AtswitchBrTpEntry .1.3.6.1.4.1.207.8.10.9.3.1.1 |
atswitchBrTpLanIdThis object uniquely identifies the lan or
Virtual lan.ro INTEGER .1.3.6.1.4.1.207.8.10.9.3.1.1.1 |
atswitchBrTpLearnedEntryDiscardsThe total number of Forwarding Database entries,
which have been or would have been learnt, but
have been discarded due to a lack of space to
store them in the Forwarding Database. If this
counter is increasing, it indicates that the
Forwarding Database is regularly becoming full (a
condition which has unpleasant performance effects
on the subnetwork). If this counter has a
significant value but is not presently increasing,
it indicates that the problem has been occurring
but is not persistent.ro Counter .1.3.6.1.4.1.207.8.10.9.3.1.1.2 |
atswitchBrTpAgingTimeThe timeout period in seconds for aging out
dynamically learned forwarding information.
802.1D-1990 recommends a default of 300 seconds.rw INTEGER .1.3.6.1.4.1.207.8.10.9.3.1.1.3 |
atswitchBrTpFdbTableA table that contains information about unicast
entries for which the bridge has forwarding and/or
filtering information. This information is used
by the transparent bridging function in
determining how to propagate a received frame. SEQUENCE OF AtswitchBrTpFdbEntry .1.3.6.1.4.1.207.8.10.9.3.3 |
atswitchBrTpFdbEntryInformation about a specific unicast MAC address
for which the bridge has some forwarding and/or
filtering information. AtswitchBrTpFdbEntry .1.3.6.1.4.1.207.8.10.9.3.3.1 |
atswitchBrTpFdbLanIdThis object uniquely identifies the lan or
Virtual lan.ro INTEGER .1.3.6.1.4.1.207.8.10.9.3.3.1.1 |
atswitchBrTpFdbAddressA unicast MAC address for which the bridge has
forwarding and/or filtering information.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.207.8.10.9.3.3.1.2 |
atswitchBrTpFdbPortEither the value '0', or the port number of the
port on which a frame having a source address
equal to the value of the corresponding instance
of atswitchBrTpFdbAddress has been seen. A value of
'0' indicates that the port number has not been
learned but that the bridge does have some
forwarding/filtering information about this
address .
Implementors are encouraged to assign the port
value to this object whenever it is learned even
for addresses for which the corresponding value of
atswitchBrTpFdbStatus is not learned(3).ro INTEGER .1.3.6.1.4.1.207.8.10.9.3.3.1.3 |
atswitchBrTpFdbStatusThe status of this entry.
The meanings of the values are:
inactive(1) : this entry is not longer valid
(e.g., it was learned but has since
aged-out), but has not yet been
flushed from the table.
active(2) : the value of the corresponding
instance of atswitchBrTpFdbPort was
active, and is being used.
other(3) : none of the following. This would
include the case where some other
MIB object (not the corresponding
instance of atswitchBrTpFdbPort ) is
being used to determine if and how
frames addressed to the value of
the corresponding instance of
atswitchBrTpFdbAddress are being
forwarded.ro Enumeration .1.3.6.1.4.1.207.8.10.9.3.3.1.4 |
atswitchBrTpPortTableA table that contains information about every
port that is associated with this transparent
bridge. SEQUENCE OF AtswitchBrTpPortEntry .1.3.6.1.4.1.207.8.10.9.3.4 |
atswitchBrTpPortEntryA list of information for each port of a
transparent bridge. AtswitchBrTpPortEntry .1.3.6.1.4.1.207.8.10.9.3.4.1 |
atswitchBrTpPortLanIdThis object uniquely identifies the lan or
Virtual lan.ro INTEGER .1.3.6.1.4.1.207.8.10.9.3.4.1.1 |
atswitchBrTpPortThe port number of the port for which this entry
contains Transparent bridging management
information.ro INTEGER .1.3.6.1.4.1.207.8.10.9.3.4.1.2 |
atswitchBrTpPortMaxInfoThe maximum size of the INFO (non-MAC) field that
this port will receive or transmit.ro INTEGER .1.3.6.1.4.1.207.8.10.9.3.4.1.3 |
atswitchBrTpPortInFramesThe number of frames that have been received by
this port from its segment. Note that a frame
received on the interface corresponding to this
port is only counted by this object if and only if
it is for a protocol being processed by the local
bridging function, including bridge management
frames.ro Counter .1.3.6.1.4.1.207.8.10.9.3.4.1.4 |
atswitchBrTpPortOutFramesThe number of frames that have been transmitted
by this port to its segment. Note that a frame
transmitted on the interface corresponding to this
port is only counted by this object if and only if
it is for a protocol being processed by the local
bridging function, including bridge management
frames.ro Counter .1.3.6.1.4.1.207.8.10.9.3.4.1.5 |
atswitchBrTpPortInDiscardsCount of valid frames received which were
discarded (i.e., filtered) by the Forwarding
Process.ro Counter .1.3.6.1.4.1.207.8.10.9.3.4.1.6 |
atswitchStaticMACGroup OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.10 |
atswitchStaticMACTableThis tables lists Mac Addresses lexicographically from the Static
table which binds MAC addresses to ports on the switch. SEQUENCE OF AtswitchStaticMACEntry .1.3.6.1.4.1.207.8.10.10.1 |
atswitchStaticMACEntryEntry in the atswitchStaticMACTable. AtswitchStaticMACEntry .1.3.6.1.4.1.207.8.10.10.1.1 |
atswitchStaticMACAddressThis object identifies the MAC Address associated
with Static MAC Table.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.207.8.10.10.1.1.1 |
atswitchStaticMACPortNumbersThis object identifies the Ports for which the above MAC
address is associated Statically in Static MAC Table. This
Object could take the port numbers as the Static Address added
can be Multicast addresses. This Object is a DisplayString
So, the input for example would be 1,5,6,8,9rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.207.8.10.10.1.1.2 |
atswitchStaticMACVlanThe Static MAC Address to be added can also be confined
to a Vlan also. If the Port does not belong to that Vlan. the Port is forced to be moved to that Vlan.rw INTEGER .1.3.6.1.4.1.207.8.10.10.1.1.3 |
atswitchPortMacAddrGroup OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.12 |
atswitchPortMACTableA table that contains information about unicast
entries seen on ports. SEQUENCE OF AtswitchPortMACEntry .1.3.6.1.4.1.207.8.10.12.1 |
atswitchPortMACEntryInformation about a specific unicast MAC address
seen on ports. AtswitchPortMACEntry .1.3.6.1.4.1.207.8.10.12.1.1 |
atswitchPortMACAddressA unicast MAC address seen on this port.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.207.8.10.12.1.1.1 |
atswitchPortMACPortThis object identifies the port on which the
atswitchPortMACAddress was seen.ro INTEGER .1.3.6.1.4.1.207.8.10.12.1.1.2 |
atswitchDebugMallocLogGroup OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.10.13 |
atswitchDebugMallocLogTableDont care.deprecated SEQUENCE OF AtswitchMallocLogEntry .1.3.6.1.4.1.207.8.10.13.1 |
atswitchMallocLogEntryEntry in the atswitchDebugMallocLogEntry.deprecated AtswitchMallocLogEntry .1.3.6.1.4.1.207.8.10.13.1.1 |
atswitchDebugMallocLogIndexThis is strictly for Debug reason and this object should
not be beleived as the correct number. This log is useful
for finding the memory leak which is stored in Leak_Table.
The Entry of this table is the address where malloc is
done and no free is done.
The size of this 6000.rodeprecated INTEGER .1.3.6.1.4.1.207.8.10.13.1.1.1 |
atswitchDebugMallocLogCallerThis is strictly for Debug reason and this object should
not be beleived as the correct number. This log is useful
for finding the memory leak which is stored in Leak_Table.
The Entry of this table is the caller address
who malloc'd .
The size of this 6000.rodeprecated INTEGER .1.3.6.1.4.1.207.8.10.13.1.1.2 |
atswitchDebugMallocLogAddressThis is strictly for Debug reason and this object should
not be beleived as the correct number. This log is useful
for finding the memory leak which is stored in Leak_Table.
The Entry of this table is the address where malloc is
done and no free is done.
The size of this 6000.rodeprecated INTEGER .1.3.6.1.4.1.207.8.10.13.1.1.3 |