ATM2-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for ATM2-MIB.
184
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
184 total| Object Name |
|---|
atm2MIB OBJECT IDENTIFIER .1.3.6.1.4.1.42.1.2.1.14 |
SNMPv2-SMI-v1 Unknown .1.3.6.1.4.1.42.1.2.1.14 |
atm2MIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.42.1.2.1.14.1 |
atmSvcVpCrossConnectTableThe ATM SVPC Cross Connect table. A
bi-directional VP cross-connect between two
switched VPLs is modeled as one entry in this
table. A Soft PVPC cross-connect, between a
soft permanent VPL and a switched VPL, is
also modeled as one entry in this table. SEQUENCE OF AtmSvcVpCrossConnectEntry .1.3.6.1.4.1.42.1.2.1.14.1.1 |
atmSvcVpCrossConnectEntryAn entry in the ATM SVPC Cross Connect table.
This entry is used to model a bi-directional
ATM VP cross-connect between two VPLs. AtmSvcVpCrossConnectEntry .1.3.6.1.4.1.42.1.2.1.14.1.1.1 |
atmSvcVpCrossConnectIndexA unique value to identify this SVPC cross-connect. INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.1.1.1 |
atmSvcVpCrossConnectLowIfIndexThe value of this object is equal to MIB II's
ifIndex value of the ATM interface port for this
SVPC cross-connect. The term low implies
that this ATM interface has the numerically lower
ifIndex value than the other ATM interface
identified in the same atmSvcVpCrossConnectEntry. InterfaceIndex -- Rsyntax Integer32 .1.3.6.1.4.1.42.1.2.1.14.1.1.1.2 |
atmSvcVpCrossConnectLowVpiThe value of this object is equal to the VPI
value associated with the SVPC cross-connect
at the ATM interface that is identified by
atmSvcVpCrossConnectLowIfIndex. The VPI value
cannot exceed the number supported by the
atmInterfaceMaxVpiBits at the low ATM interface
port. AtmVpIdentifier -- Rsyntax INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.1.1.3 |
atmSvcVpCrossConnectHighIfIndexThe value of this object is equal to MIB II's
ifIndex value of the ATM interface port for
this SVC VP cross-connect. The term high
implies that this ATM interface has the
numerically higher ifIndex value than the
other ATM interface identified in the same
atmSvcVpCrossConnectEntry. InterfaceIndex -- Rsyntax Integer32 .1.3.6.1.4.1.42.1.2.1.14.1.1.1.4 |
atmSvcVpCrossConnectHighVpiThe value of this object is equal to the VPI
value associated with the SVPC cross-connect
at the ATM interface that is identified by
atmSvcVpCrossConnectHighIfIndex. The VPI value
cannot exceed the number supported by the
atmInterfaceMaxVpiBits at the high ATM interface
port. AtmVpIdentifier -- Rsyntax INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.1.1.5 |
atmSvcVpCrossConnectCreationTimeThe value of MIB II's sysUpTime object
at the time this bi-directional SVPC
cross-connect was created. If the current
state was entered prior to the last
re-initialization of the agent, then this
object contains a zero value.ro TimeStamp -- Rsyntax TimeTicks .1.3.6.1.4.1.42.1.2.1.14.1.1.1.6 |
atmSvcVpCrossConnectRowStatusThis object is used to delete rows in the
atmSvcVpCrossConnectTable.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.4.1.42.1.2.1.14.1.1.1.7 |
atmSvcVcCrossConnectTableThe ATM SVCC Cross Connect table. A
bi-directional VC cross-connect between two
switched VCLs is modeled as one entry in
this table. A Soft PVCC cross-connect,
between a soft permanent VCL and a switched
VCL, is also modeled as one entry in this
table. SEQUENCE OF AtmSvcVcCrossConnectEntry .1.3.6.1.4.1.42.1.2.1.14.1.2 |
atmSvcVcCrossConnectEntryAn entry in the ATM SVCC Cross Connect table.
This entry is used to model a bi-directional ATM
VC cross-connect between two VCLs. AtmSvcVcCrossConnectEntry .1.3.6.1.4.1.42.1.2.1.14.1.2.1 |
atmSvcVcCrossConnectIndexA unique value to identify this SVCC cross-connect. INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.2.1.1 |
atmSvcVcCrossConnectLowIfIndexThe value of this object is equal to MIB II's
ifIndex value of the ATM interface port for this
SVCC cross-connect. The term low implies that
this ATM interface has the numerically lower
ifIndex value than the other ATM interface
identified in the same atmSvcVcCrossConnectEntry. InterfaceIndex -- Rsyntax Integer32 .1.3.6.1.4.1.42.1.2.1.14.1.2.1.2 |
atmSvcVcCrossConnectLowVpiThe value of this object is equal to the VPI
value associated with the SVCC cross-connect
at the ATM interface that is identified by
atmSvcVcCrossConnectLowIfIndex. The VPI value
cannot exceed the number supported by the
atmInterfaceMaxVpiBits at the low ATM interface
port. AtmVpIdentifier -- Rsyntax INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.2.1.3 |
atmSvcVcCrossConnectLowVciThe value of this object is equal to the VCI
value associated with the SVCC cross-connect
at the ATM interface that is identified by
atmSvcVcCrossConnectLowIfIndex. The VCI value
cannot exceed the number supported by the
atmInterfaceMaxVciBits at the low ATM interface
port. AtmVcIdentifier -- Rsyntax INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.2.1.4 |
atmSvcVcCrossConnectHighIfIndexThe value of this object is equal to MIB II's
ifIndex value for the ATM interface port for
this SVCC cross-connect. The term high implies
that this ATM interface has the numerically
higher ifIndex value than the other ATM interface
identified in the same atmSvcVcCrossConnectEntry. InterfaceIndex -- Rsyntax Integer32 .1.3.6.1.4.1.42.1.2.1.14.1.2.1.5 |
atmSvcVcCrossConnectHighVpiThe value of this object is equal to the VPI
value associated with the SVCC cross-connect
at the ATM interface that is identified by
atmSvcVcCrossConnectHighIfIndex. The VPI value
cannot exceed the number supported by the
atmInterfaceMaxVpiBits at the high ATM interface
port. AtmVpIdentifier -- Rsyntax INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.2.1.6 |
atmSvcVcCrossConnectHighVciThe value of this object is equal to the VCI
value associated with the SVCC cross-connect
at the ATM interface that is identified by
atmSvcVcCrossConnectHighIfIndex. The VCI value
cannot exceed the number supported by the
atmInterfaceMaxVciBits at the high ATM interface
port. AtmVcIdentifier -- Rsyntax INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.2.1.7 |
atmSvcVcCrossConnectCreationTimeThe value of MIB II's sysUpTime object
at the time this bi-directional SVCC
cross-connect was created. If the current
state was entered prior to the last
re-initialization of the agent, then this
object contains a zero value.ro TimeStamp -- Rsyntax TimeTicks .1.3.6.1.4.1.42.1.2.1.14.1.2.1.8 |
atmSvcVcCrossConnectRowStatusThis object is used to delete rows in the
atmSvcVcCrossConnectTable.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.4.1.42.1.2.1.14.1.2.1.9 |
atmSigStatTableThis table contains ATM interface signalling monitoring
, one entry per ATM signalling interface. SEQUENCE OF AtmSigStatEntry .1.3.6.1.4.1.42.1.2.1.14.1.3 |
atmSigStatEntryThis list contains signalling statistics variables. AtmSigStatEntry .1.3.6.1.4.1.42.1.2.1.14.1.3.1 |
atmSigSSCOPConEventsSSCOP Connection Events Counter. This
counter counts the sum of the following errors:
1) SSCOP Connection Disconnect Counter
The abnormal occurrence of this event is
characterized by the expiry of Timer_NO_RESPONSE.
(This event is communicated to the layer management
with MAA-ERROR code P. See ITU-T Q.2110 [13].)
2) SSCOP Connection Initiation Failure
This condition indicates the inability to establish
an SSCOP connection. This event occurs whenever the
number of expiries of the connection control timer
(Timer_CC) exceeds the MaxCC or upon receipt of a
connection reject message BGREJ PDU. (This event is
communicated to layer management with MAA-ERROR
code O. See ITU-T Q.2110.)
3) SSCOP Connection Re-Establ/Resynch
This event occurs upon receipt of a BGN PDU or RESYNC
PDU.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.1 |
atmSigSSCOPErrdPdusSSCOP Errored PDUs Counter. This counter counts the
sum of the following errors:
1) Invalid PDUs.
These are defined in SSCOP and consist of PDUs
with incorrect length (MAA-ERROR code U),
undefined PDU type code or not 32-bit aligned.
2) PDUs that result in MAA error codes and are
discarded
See Errors A-M and Q-T defined in ITU-T Q.2110 [13].ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.2 |
atmSigDetectSetupAttemptsCall Setup Attempts Counter. This counter counts
the number of call setup attempts(both successful
and unsuccessful) detected on this interface.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.3 |
atmSigEmitSetupAttemptsCall Setup Attempts Counter. This counter counts the
number of call setup attempts(both successful and
unsuccessful) transmitted on this interface.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.4 |
atmSigDetectUnavailRoutesNumber of Route Unavailability detected on this
interface. This counter is incremented when a RELEASE,
RELEASE COMPLETE (only when not preceded by a RELEASE
mesg for the same call), ADD PARTY REJECT, or STATUS
message that contains one of the following cause code
values is received (Note: These cause values apply to
both UNI3.0 and UNI3.1):
Cause Value Meaning
1 unallocated (unassigned) number
2 no route to specified transit network
3 no route to destination
NOTE: For this counter, RELEASE COMPLETE
messages that are a reply to a previous RELEASE
message and contain the same cause value, are
redundant (for counting purposes) and should not
be counted.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.5 |
atmSigEmitUnavailRoutesNumber of Route Unavailability transmitted from this
interface. This counter is incremented when a RELEASE,
RELEASE COMPLETE (only when not preceded by a RELEASE
mesg for the same call), ADD PARTY REJECT, or STATUS
message that contains one of the following cause code
values is transmitted (Note: These cause values apply
to both UNI3.0 and UNI3.1):
Cause Value Meaning
1 unallocated (unassigned) number
2 no route to specified transit network
3 no route to destination
NOTE: For this counter, RELEASE COMPLETE
messages that are a reply to a previous RELEASE
message and contain the same cause value, are
redundant (for counting purposes) and should not
be counted.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.6 |
atmSigDetectUnavailResrcsNumber of Resource Unavailability detected on this
interfrace. This counter is incremented when a
RELEASE, RELEASE COMPLETE (only when not preceded by a
RELEASE mesg for the same call), ADD PARTY REJECT, or
STATUS message that contains one of the following cause
code values is received (Note: These cause values apply
to both UNI3.0 and UNI3.1 unless otherwise stated):
Cause Value Meaning
35 requested VPCI/VCI not available
37 user cell rate not available (UNI3.1
only)
38 network out of order
41 temporary failure
45 no VPCI/VCI available
47 resource unavailable, unspecified
49 Quality of Service unavailable
51 user cell rate not available (UNI3.0
only)
58 bearer capability not presently
available
63 Service or option not available,
unspecified
92 too many pending add party requests
NOTE: For this counter, RELEASE COMPLETE
messages that are a reply to a previous RELEASE
message and contain the same cause value, are
redundant (for counting purposes) and should not
be counted.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.7 |
atmSigEmitUnavailResrcsNumber of Resource Unavailability transmitted from
this interfrace. This counter is incremented when a
RELEASE, RELEASE COMPLETE (only when not preceded by a
RELEASE mesg for the same call), ADD PARTY REJECT, or
STATUS message that contains one of the following cause
code values is transmitted (Note: These cause values
apply to both UNI3.0 and UNI3.1 unless otherwise
stated):
Cause Value Meaning
35 requested VPCI/VCI not available
37 user cell rate not available (UNI3.1
only)
38 network out of order
41 temporary failure
45 no VPCI/VCI available
47 resource unavailable, unspecified
49 Quality of Service unavailable
51 user cell rate not available (UNI3.0
only)
58 bearer capability not presently
available
63 Service or option not available,
unspecified
92 too many pending add party requests
NOTE: For this counter, RELEASE COMPLETE
messages that are a reply to a previous RELEASE
message and contain the same cause value, are
redundant (for counting purposes) and should not
be counted.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.8 |
atmSigDetectCldPtyEventsNumber of Called Party Responsible For Unsuccessful
Call detected on this interface. This counter is
incremented when a RELEASE, RELEASE COMPLETE (only when
not preceded by a RELEASE mesg for the same call), ADD
PARTY REJECT, or STATUS message that contains one of
the following cause code values is received (Note:
These cause values apply to both UNI3.0 and UNI3.1):
Cause Value Meaning
17 user busy
18 no user responding
21 call rejected
22 number changed
23 user rejects all calls with calling
line id restriction (CLIR)
27 destination out of order
31 normal, unspecified
88 incompatible destination
NOTE: For this counter, RELEASE COMPLETE
messages that are a reply to a previous RELEASE
message and contain the same cause value, are
redundant (for counting purposes) and should not
be counted.
Note: Cause Value #30 'response to STATUS ENQUIRY'
was not included in this memo since it did not apply
to a hard failure.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.9 |
atmSigEmitCldPtyEventsNumber of Called Party Responsible For Unsuccessful Call
transmitted from this interface. This counter is
incremented when a RELEASE, RELEASE COMPLETE (only
when not preceded by a RELEASE mesg for the same call),
ADD PARTY REJECT, or STATUS message that contains one
of the following cause code values is
transmitted (Note: These cause values apply to both
UNI3.0 and UNI3.1):
Cause Value Meaning
17 user busy
18 no user responding
21 call rejected
22 number changed
23 user rejects all calls with calling
line id restriction (CLIR)
27 destination out of order
31 normal, unspecified
88 incompatible destination
NOTE: For this counter, RELEASE COMPLETE
messages that are a reply to a previous RELEASE
message and contain the same cause value, are
redundant (for counting purposes) and should not
be counted.
Note: Cause Value #30 'response to STATUS ENQUIRY'
was not included in this memo since it did not apply
to a hard failure.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.10 |
atmSigDetectMsgErrorsNumber of Incorrect Messages detected on this
interface. The Incorrect Messages Counter reflects any
sort of incorrect information in a message. This
includes:
- RELEASE, RELEASE COMPLETE, ADD PARTY REJECT,
and STATUS messages transmitted, that contain any of
the Cause values listed below.
- Ignored messages. These messages are dropped
because the message was so damaged that it could
not be further processed. A list of dropped
messages is compiled below:
1. Message with invalid protocol discriminator
2. Message with errors in the call reference I.E.
- Bits 5-8 of the first octet not equal to
'0000'
- Bits 1-4 of the first octet indicating a
length other than 3 octets
- RELEASE COMPLETE message received with a
call reference that does not relate to a
call active or in progress
- SETUP message received with call reference
flag incorrectly set to 1
- SETUP message received with a call
reference for a call that is already
active or in progress.
3. Message too short
The following cause values are monitored by this
counter (Note: These cause values apply to both UNI3.0
and UNI3.1 unless otherwise stated):
Cause Value Meaning
10 VPCI/VCI unacceptable (UNI3.0 only)
36 VPCI/VCI assignment failure (UNI3.1 only)
81 invalid call reference value
82 identified channel does not exist
89 invalid endpoint reference
96 mandatory information element is missing
97 message type non-existent or not
implemented
99 information element non-existent or not
implemented
100 invalid information element contents
101 message not compatible with call state
104 incorrect message length
111 protocol error, unspecified
NOTE: For this counter, RELEASE COMPLETE
messages that are a reply to a previous RELEASE
message and contain the same cause value, are
redundant (for counting purposes) and should not
be counted.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.11 |
atmSigEmitMsgErrorsNumber of Incorrect Messages transmitted on this
interface. The Incorrect Messages Counter reflects any
sort of incorrect information in a message. This
includes:
- RELEASE, RELEASE COMPLETE, ADD PARTY REJECT,
and STATUS messages transmitted or
received, that contain any of the Cause values
listed below.
- Ignored messages. These messages are dropped
because the message was so damaged that it could
not be further processed. A list of dropped
messages is compiled below:
1. Message with invalid protocol discriminator
2. Message with errors in the call reference I.E.
- Bits 5-8 of the first octet not equal to
'0000'
- Bits 1-4 of the first octet indicating a
length other than 3 octets
- RELEASE COMPLETE message received with a
call reference that does not relate to a
call active or in progress
- SETUP message received with call reference
flag incorrectly set to 1
- SETUP message received with a call
reference for a call that is already
active or in progress.
3. Message too short
The following cause values are monitored by this
counter (Note: These cause values apply to both UNI3.0
and UNI3.1 unless otherwise stated):
Cause Value Meaning
10 VPCI/VCI unacceptable (UNI3.0 only)
36 VPCI/VCI assignment failure (UNI3.1 only)
81 invalid call reference value
82 identified channel does not exist
89 invalid endpoint reference
96 mandatory information element is missing
97 message type non-existent or not
implemented
99 information element non-existent or not
implemented
100 invalid information element contents
101 message not compatible with call state
104 incorrect message length
111 protocol error, unspecified
NOTE: For this counter, RELEASE COMPLETE
messages that are a reply to a previous RELEASE
message and contain the same cause value, are
redundant (for counting purposes) and should not
be counted.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.12 |
atmSigDetectClgPtyEventsNumber of Calling Party Events detected on this
interface. This counter monitors error events that
occur due to the originating user doing something
wrong. This counter is incremented when a RELEASE,
RELEASE COMPLETE (only when not preceded by a RELEASE
mesg for the same call), ADD PARTY REJECT, or STATUS
message that contains one of the following cause code
values is received (Note: These cause values apply to
both UNI3.0 and UNI3.1):
Cause Value Meaning
28 invalid number format (address incomplete)
43 access information discarded
57 bearer capability not authorized
65 bearer capability not implemented
73 unsupported combination of traffic
parameters
78 AAL parameters cannot be supported (UNI3.1
only)
91 invalid transit network selection
93 AAL parameters cannot be supported (UNI3.0
only)
NOTE: For this counter, RELEASE COMPLETE
messages that are a reply to a previous RELEASE
message and contain the same cause value, are
redundant (for counting purposes) and should not
be counted.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.13 |
atmSigEmitClgPtyEventsNumber of Calling Party Events transmitted from this
interface. This counter monitors error events that
occur due to the originating user doing something
wrong. This counter is incremented when a RELEASE,
RELEASE COMPLETE (only when not preceded by a RELEASE
mesg for the same call), ADD PARTY REJECT, or STATUS
message that contains one of the following cause code
values is transmitted (Note: These cause values apply
to both UNI3.0 and UNI3.1):
Cause Value Meaning
28 invalid number format (address incomplete)
43 access information discarded
57 bearer capability not authorized
65 bearer capability not implemented
73 unsupported combination of traffic
parameters
78 AAL parameters cannot be supported (UNI3.1
only)
91 invalid transit network selection
93 AAL parameters cannot be supported (UNI3.0
only)
NOTE: For this counter, RELEASE COMPLETE
messages that are a reply to a previous RELEASE
message and contain the same cause value, are
redundant (for counting purposes) and should not
be counted.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.14 |
atmSigDetectTimerExpiredsNumber of Timer Expiries detected on this interface.
The Timer Expiries Counter provides a count of network
timer expiries, and to some extent, host or switch
timer expiries. The conditions for incrementing this
counter are:
- Expiry of any network timer
- Receipt of a RELEASE or RELEASE COMPLETE
message with Cause #102, 'recovery on
timer expiry'.
NOTE: For this counter, RELEASE COMPLETE messages
that are a reply to a previous RELEASE message and
contain the same cause value, are redundant (for
counting purposes) and should not be counted.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.15 |
atmSigEmitTimerExpiredsNumber of Timer Expiries transmitted from this
interface. The Timer Expiries Counter provides a count
of network timer expiries, and to some extent, host or
switch timer expiries. The conditions for incrementing
this counter are:
- Expiry of any network timer
- Receipt of a RELEASE or RELEASE COMPLETE
message with Cause #102, 'recovery on
timer expiry'.
NOTE: For this counter, RELEASE COMPLETE messages
that are a reply to a previous RELEASE message and
contain the same cause value, are redundant (for
counting purposes) and should not be counted.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.16 |
atmSigDetectRestartsNumber of Restart Activity errors detected on this
interface. The Restart Activity Counter provides a
count of host, switch, or network restart activity.
This counter is incremented when receiving a RESTART
message.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.17 |
atmSigEmitRestartsNumber of Restart Activity errors transmitted from
this interface. The Restart Activity Counter provides
a count of host, switch, or network restart activity.
This counter is incremented when transmitting a RESTART
message.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.18 |
atmSigInEstablsNumber of SVC VCCs established at this signalling
entity for incoming connections.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.19 |
atmSigOutEstablsNumber of SVC VCCs established at this signalling
entity for outgoing connections.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.3.1.20 |
atmSigSupportTableThis table contains ATM local interface configuration
parameters, one entry per ATM signalling interface. SEQUENCE OF AtmSigSupportEntry .1.3.6.1.4.1.42.1.2.1.14.1.4 |
atmSigSupportEntryThis list contains signalling configuration parameters
and state variables. AtmSigSupportEntry .1.3.6.1.4.1.42.1.2.1.14.1.4.1 |
atmSigSupportClgPtyNumDelThis object indicates whether the Calling Party Number
Information Element is transferred to the called party
address. The value of this object can be:
- enabled(1) This Information Element is transferred
to the called party
- disabled(2) This Information Element is NOT
transferred to the called party.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.4.1.1 |
atmSigSupportClgPtySubAddrThis object indicates whether to accept and transfer
the Calling Party Subaddress Information Element from
the calling party to the called party. Calling party
subaddress information shall only be transferred to the
called party if calling party number delivery is
enabled (i.e., atmSigSupportClgPtyNumDel =
'enabled(1)'. The value of this object can be:
- enabled(1) This Information Element is transferred
to the called party
- disabled(2) This Information Element is NOT
transferred to the called party.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.4.1.2 |
atmSigSupportCldPtySubAddrThis object indicates whether to accept, transfer, and
deliver the Called Party Subaddress Information Element
from the calling party to the called party. The value
of this object can be:
- enabled(1) This Information Element is transferred
to the called party
- disabled(2) This Information Element is NOT
transferred to the called party.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.4.1.3 |
atmSigSupportHiLyrInfoThis object indicates whether to accept, transfer, and
deliver the Broadband High Layer Information Element
from the calling party to the called party. The value
of this object can be:
- enabled(1) This Information Element is transferred
to the called party
- disabled(2) This Information Element is NOT
transferred to the called party.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.4.1.4 |
atmSigSupportLoLyrInfoThis object indicates whether to accept, transfer, and
deliver the Broadband Low Layer Information Element
from the calling party to the called party. The value
of this object can be:
- enabled(1) This Information Element is transferred
to the called party
- disabled(2) This Information Element is NOT
transferred to the called party.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.4.1.5 |
atmSigSupportBlliRepeatIndThis object indicates whether to accept, transfer, and
deliver the Broadband Repeat Indicator with two or
three instances of the Broadband Low Layer Information
Element for low layer information selection from the
calling party to the called party. This object shall
only be transferred if atmSigSupportLoLyrInfo =
'enabled(1)'. The value of this object can be:
- enabled(1) This Information Element is transferred
to the called party
- disabled(2) This Information Element is NOT
transferred to the called party.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.4.1.6 |
atmSigSupportAALInfoThis object indicates whether to accept, transfer, and
deliver the ATM Adaptation Layer Parameters Information
Element from the calling party to the called party.
The value of this object can be:
- enabled(1) This Information Element is transferred
to the called party
- disabled(2) This Information Element is NOT
transferred to the called party.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.4.1.7 |
atmSigSupportPrefCarrierThis parameter identifies the carrier to which
intercarrier calls originated from this interface are
routed when transit network selection information is
not provided by the calling party. If a Carrier
Identification Code (CIC) is used the parameter shall
contain the CIC. For three-digit CICs, the first octet
shall be '0' and the CIC is contained in the three
following octets. If the preferred carrier feature is
not supported the value is a zero-length string.rw OCTET STRING .1.3.6.1.4.1.42.1.2.1.14.1.4.1.8 |
atmSigDescrParamTableA table contains signalling capabilities of VCLs
except the Traffic Descriptor. Traffic
descriptors are described in the
atmTrafficDescrParamTable. SEQUENCE OF AtmSigDescrParamEntry .1.3.6.1.4.1.42.1.2.1.14.1.5 |
atmSigDescrParamEntryEach entry in this table represents a set of
signalling capabilities that can be applied to a
VCL. There is no requirement for unique entries,
except that the index must be unique. Objects
atmSigDescrParamRowStatus is required during
creation. AtmSigDescrParamEntry .1.3.6.1.4.1.42.1.2.1.14.1.5.1 |
atmSigDescrParamIndexThe value of this object is used by the
atmVclExtTable to identify a row in this table. AtmSigDescrParamIndex -- Rsyntax INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.5.1.1 |
atmSigDescrParamAalTypeThe AAL type. The value of this object is set to
other(1) when not defined.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.5.1.2 |
atmSigDescrParamAalSscsTypeThe SSCS type used by this entry.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.5.1.3 |
atmSigDescrParamBhliTypeThe Broadband high layer type.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.5.1.4 |
atmSigDescrParamBhliInfoThe Broadband high layer information. When
atmSigDescrParamBhliType is set to iso(2), the
value of this object is a zero length string.
When atmSigDescrParamBhliType is set to
hiProfile(4), the value of this object is a length
of 4 octet string containing user to user profile
identifier. When atmSigDescrParamBhliType is set
to vendorSpecific(4), the value of this object
is a length of 7 octet string. The most
significant 3 octets consist of a globally-
administered OUI, the least significant 4 octets
are the vender administered application OUI.rw OCTET STRING .1.3.6.1.4.1.42.1.2.1.14.1.5.1.5 |
atmSigDescrParamBbcConnConfThe Broadband bearer capability user plane
connection configuration parameter.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.5.1.6 |
atmSigDescrParamBlliLayer2The Broadband low layer information, protocol
type of layer 2. The value of this object is
other(1) if layer 2 protocol is not used.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.5.1.7 |
atmSigDescrParamBlliLayer3The Broadband low layer information, protocol
type of layer 3. The value of this object is
other(1) if layer 3 protocol is not used.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.5.1.8 |
atmSigDescrParamBlliPktSizeThe default packet size defined in B-LLI.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.5.1.9 |
atmSigDescrParamBlliSnapIdThe SNAP ID used for Broadband low layer protocol
layer 3. The value of this object is other(1) if
atmSigDescrParamBlliLayer3 is set to other(1).rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.5.1.10 |
atmSigDescrParamBlliOuiPidThe OUI/PID encoding for Broadband low layer
protocol layer 3. The value of this object is a
zero length string if atmSigDescrParamBlliLayer3
is set to none(1). When used, it is always 5
octets with the most significant octet as the OUI
Octet 1 and the least significant octet as the PID
Octet 2.rw OCTET STRING .1.3.6.1.4.1.42.1.2.1.14.1.5.1.11 |
atmSigDescrParamRowStatusThis object is used to create and delete rows in
the atmSigDescrParamTable. Writable values are:
-'createAndWait' which allows manager to create an
entry first and fill in the parameters later.
-'active' which allows manager to set the entry to
be available to users. -'destroy' which allows
manager to delete an entry from this table.
Readable values are: -'createAndWait' which means
the entry is created but not available to be used.
-'active' means it is active and ready to be used
by agent or manager.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.4.1.42.1.2.1.14.1.5.1.12 |
atmIfRegisteredAddrTableThis table contains a list of ATM addresses that can
be used for calls to and from a given interface by a
switch or service. The ATM addresses are either
registered by the endsystem via ILMI or statically
configured. This table does not expose PNNI
reachability information. ILMI registered addresses
cannot be deleted using this table. This table only
applies to switches and network services. SEQUENCE OF AtmIfRegisteredAddrEntry .1.3.6.1.4.1.42.1.2.1.14.1.6 |
atmIfRegisteredAddrEntryAn entry in the ATM Interface Registered Address
table. AtmIfRegisteredAddrEntry .1.3.6.1.4.1.42.1.2.1.14.1.6.1 |
atmIfRegAddrAddressAn address registered for a given switch or service
interface. AtmAddr -- Rsyntax OCTET STRING .1.3.6.1.4.1.42.1.2.1.14.1.6.1.1 |
atmIfRegAddrAddressSourceThe type of address source for a given ATM Address.
The value dynamic(3) is indicated when ILMI is used.ro Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.6.1.2 |
atmIfRegAddrOrgScopeThis object indicates the organizational scope for the
referenced address. The information of the referenced
address shall not be distributed outside the indicated
scope. Refer to Annex 5.3 of ATM Forum UNI Signalling
4.0 for guidelines regarding the use of organizational
scopes.
This value cannot be configured for ILMI-registered
addresses.
The default values for organizational scope are
localNetwork(1) for ATM group addresses, and global(15)
for individual addresses.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.6.1.3 |
atmIfRegAddrRowStatusThis object is used to create and delete rows in the
atmIfRegisteredAddrTable. Rows created dynamically
(e.g., ILMI-registered addresses) cannot be deleted
using this object.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.4.1.42.1.2.1.14.1.6.1.4 |
atmVclAddrTableThis table provides a mapping between the
atmVclTable and the ATM called party/calling party
address. This table can be used to retrieve the
calling party and called party ATM address pair
for a given Vcl. Note that there can be more than
one pair of calling party and called party ATM
addresses for a VCL in a point to multi-point
call. SEQUENCE OF AtmVclAddrEntry .1.3.6.1.4.1.42.1.2.1.14.1.7 |
atmVclAddrEntryEach entry in this table represents a binding
between a VCL and an ATM address associated with
this call. This ATM address can be either the
called party address or the calling party address.
There can be more than one pair of calling/called
party ATM addresses associated with the VCL entry
for point to multi-point calls. Objects
atmVclAddrAddr, atmVclAddrType, and
atmVclAddrRowStatus are required during row
creation. AtmVclAddrEntry .1.3.6.1.4.1.42.1.2.1.14.1.7.1 |
atmVclAddrAddrAn ATM address on one end of the VCL. For SVCs,
the agent supplies the value of this object at
creation time. For PVCs, manager can supply the
value of this object during or after the PVC
creation. AtmAddr -- Rsyntax OCTET STRING .1.3.6.1.4.1.42.1.2.1.14.1.7.1.1 |
atmVclAddrTypeThe type of ATM Address represented by the object
atmVclAddrAddr. Choices are either the calling
party ATM address or the called party ATM
address.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.7.1.2 |
atmVclAddrRowStatusThis object is used to create or destroy an entry
from this table.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.4.1.42.1.2.1.14.1.7.1.3 |
atmAddrVclTableThis table provides an alternative way to
retrieve the atmVclTable. This table can be used
to retrieve the indexing to the atmVclTable by an
ATM address. SEQUENCE OF AtmAddrVclEntry .1.3.6.1.4.1.42.1.2.1.14.1.8 |
atmAddrVclEntryEach entry in this table represents an entry in
the atmVclTable of the ATM MIB [1] by it's ATM
address. The ATM address is either the calling or
called party ATM address of the call. Entries in
this table are read only. They show up when
entries are created in the atmVclAddrTable. AtmAddrVclEntry .1.3.6.1.4.1.42.1.2.1.14.1.8.1 |
atmAddrVclAtmIfIndexThe interface index of the ATM interface where
this VCL pertains to. This object combined with
the atmAddrVclVpi and atmAddrVclVci objects serves
as an index to the atmVclTable. InterfaceIndex -- Rsyntax Integer32 .1.3.6.1.4.1.42.1.2.1.14.1.8.1.1 |
atmAddrVclVpiThe VPI value of the VCL. This object combined
with the atmAddrVclAtmIfIndex and atmAddrVclVci
objects serves as an index to the atmVclTable. AtmVpIdentifier -- Rsyntax INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.8.1.2 |
atmAddrVclVciThe VCI value of the VCL. This object combined
with the atmAddrVclAtmIfIndex and atmAddrVclVpi
objects serves as an index to the atmVclTable. AtmVcIdentifier -- Rsyntax INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.8.1.3 |
atmAddrVclAddrTypeThe type of ATM Address represented by the object
atmVclAddrAddr. Choices are either calling party
address or called party address.ro Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.8.1.4 |
atmVplStatTableThis table contains all statistic counters per
VPL. It is used to monitor the usage of the VPL
in terms of incoming cells and outgoing cells. SEQUENCE OF AtmVplStatEntry .1.3.6.1.4.1.42.1.2.1.14.1.9 |
atmVplStatEntryEach entry in this table represents a VPL. AtmVplStatEntry .1.3.6.1.4.1.42.1.2.1.14.1.9.1 |
atmVplStatTotalCellInsThe total number of valid ATM cells received by
this VPL including both CLP=0 and CLP=1 cells.
The cells are counted prior to the application of
the traffic policing.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.9.1.1 |
atmVplStatClp0CellInsThe number of valid ATM cells received by this
VPL with CLP=0. The cells are counted prior to
the application of the traffic policing.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.9.1.2 |
atmVplStatTotalDiscardsThe total number of valid ATM cells discarded by
the traffic policing entity. This includes cells
orginally received with CLP=0 and CLP=1.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.9.1.3 |
atmVplStatClp0DiscardsThe total number of valid ATM cells received with
CLP=0 an discarded by the traffic policing
entity.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.9.1.4 |
atmVplStatTotalCellOutsThe total number of valid ATM cells transmitted
by this VPL. This includes both CLP=0 and CLP=1
cells.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.9.1.5 |
atmVplStatClp0CellOutsThe total number of valid ATM cells transmitted
with CLP=0 by this VPL.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.9.1.6 |
atmVplStatTaggedOutsThe total number of valid ATM cells tagged by the
traffic policing entity from CLP=0 to CLP=1 and
transmitted by this VPL.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.9.1.7 |
atmVplLogicalPortTableIndicates whether the VPL is an ATM Logical Port
interface (ifType=80). SEQUENCE OF AtmVplLogicalPortEntry .1.3.6.1.4.1.42.1.2.1.14.1.10 |
atmVplLogicalPortEntryAn entry with information about the ATM Logical
Port interface. AtmVplLogicalPortEntry .1.3.6.1.4.1.42.1.2.1.14.1.10.1 |
atmVplLogicalPortDefIndicates whether the VPC at this VPL interface
is an ATM Logical Port interface.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.10.1.1 |
atmVplLogicalPortIndexThe ifTable index of the ATM logical port
interface associated with this VPL. Only valid if
the value of atmVplLogicalPortDef is isLogicalIf,
and the VPL row is active.ro InterfaceIndex -- Rsyntax Integer32 .1.3.6.1.4.1.42.1.2.1.14.1.10.1.2 |
atmVclStatTableThis table contains all statistic counters per
VCL. It is used to monitor the usage of the VCL
in terms of incoming cells and outgoing cells. SEQUENCE OF AtmVclStatEntry .1.3.6.1.4.1.42.1.2.1.14.1.11 |
atmVclStatEntryEach entry in this table represents a VCL. AtmVclStatEntry .1.3.6.1.4.1.42.1.2.1.14.1.11.1 |
atmVclStatTotalCellInsThe total number of valid ATM cells received by
this VCL including both CLP=0 and CLP=1 cells.
The cells are counted prior to the application of
the traffic policing.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.11.1.1 |
atmVclStatClp0CellInsThe number of valid ATM cells received by this
VCL with CLP=0. The cells are counted prior to
the application of the traffic policing.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.11.1.2 |
atmVclStatTotalDiscardsThe total number of valid ATM cells discarded by
the traffic policing entity. This includes cells
orginally received with CLP=0 and CLP=1.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.11.1.3 |
atmVclStatClp0DiscardsThe total number of valid ATM cells received with
CLP=0 an discarded by the traffic policing
entity.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.11.1.4 |
atmVclStatTotalCellOutsThe total number of valid ATM cells transmitted
by this VCL. This includes both CLP=0 and CLP=1
cells.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.11.1.5 |
atmVclStatClp0CellOutsThe total number of valid ATM cells transmitted
with CLP=0 by this VCL.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.11.1.6 |
atmVclStatTaggedOutsThe total number of valid ATM cells tagged by the
traffic policing entity from CLP=0 to CLP=1 and
transmitted by this VCL.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.11.1.7 |
atmAal5VclStatTableThis table provides a collection of objects
providing AAL5 configuration and performance
statistics of a VCL. SEQUENCE OF AtmAal5VclStatEntry .1.3.6.1.4.1.42.1.2.1.14.1.12 |
atmAal5VclStatEntryEach entry in this table represents a VCL. AtmAal5VclStatEntry .1.3.6.1.4.1.42.1.2.1.14.1.12.1 |
atmAal5VclInPktsThe number of AAL5 CPCS PDUs received on the AAL5
VCC at the interface identified by the ifIndex.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.12.1.1 |
atmAal5VclOutPktsThe number of AAL5 CPCS PDUs transmitted on the
AAL5 VCC at the interface identified by the
ifIndex.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.12.1.2 |
atmAal5VclInOctetsThe number of octets contained in AAL5 CPCS PDUs
received on the AAL5 VCC at the interface
identified by the ifIndex.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.12.1.3 |
atmAal5VclOutOctetsThe number of octets contained in AAL5 CPCS PDUs
transmitted on the AAL5 VCC at the interface
identified by the ifIndex.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.12.1.4 |
atmVclGenTableGeneral Information for each VC. SEQUENCE OF AtmVclGenEntry .1.3.6.1.4.1.42.1.2.1.14.1.13 |
atmVclGenEntryAn entry with general information
about the ATM VC. AtmVclGenEntry .1.3.6.1.4.1.42.1.2.1.14.1.13.1 |
atmVclGenSigDescrIndexThe value of this object identifies the
row in the ATM Signalling Descriptor
Parameter Table which applies to this
VCL.rw AtmSigDescrParamIndex -- Rsyntax INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.13.1.1 |
atmInterfaceExtTableThis table contains ATM interface
configuration and monitoring information not
defined in the atmInterfaceConfTable from the
ATM-MIB [1]. This includes the type of
connection setup procedures, ILMI information,
and information on the VPI/VCI range. SEQUENCE OF AtmInterfaceExtEntry .1.3.6.1.4.1.42.1.2.1.14.1.14 |
atmInterfaceExtEntryAn entry extends the
atmInterfaceConfEntry defined in [1]. Each
entry corresponds to an ATM
interface. AtmInterfaceExtEntry .1.3.6.1.4.1.42.1.2.1.14.1.14.1 |
atmIntfConfigTypeThe type of connection setup procedures
configured for the ATM interface. Setting this
variable to a value of 'other' is not allowed.rw AtmInterfaceType -- Rsyntax INTEGER { -- other(1), -- autoConfig(2), -- ituDss2(3), -- atmfUni3Dot0(4), -- atmfUni3Dot1(5), -- atmfUni4Dot0(6), -- atmfIispUni3Dot0(7), -- atmfIispUni3Dot1(8), -- atmfIispUni4Dot0(9), -- atmfPnni1Dot0(10), -- atmfBici2Dot0(11), -- atmfUniPvcOnly(12), -- atmfNniPvcOnly(13) -- } .1.3.6.1.4.1.42.1.2.1.14.1.14.1.1 |
atmIntfActualTypeThe type of connection setup procedures
currently being used on the interface. This may
reflect a manually configured value for the
interface type, or may be determined by other
means such as auto-configuration. A value of
`autoConfig' indicates that auto-configuration
was requested but has not yet been completed.ro AtmInterfaceType -- Rsyntax INTEGER { -- other(1), -- autoConfig(2), -- ituDss2(3), -- atmfUni3Dot0(4), -- atmfUni3Dot1(5), -- atmfUni4Dot0(6), -- atmfIispUni3Dot0(7), -- atmfIispUni3Dot1(8), -- atmfIispUni4Dot0(9), -- atmfPnni1Dot0(10), -- atmfBici2Dot0(11), -- atmfUniPvcOnly(12), -- atmfNniPvcOnly(13) -- } .1.3.6.1.4.1.42.1.2.1.14.1.14.1.2 |
atmIntfConfigSideThe configured role of the managed entity as one
side of the ATM interface. This value does not
apply when the object atmIntfConfigType is set to
`autoConfig', `atmfPnni1Dot0', or
`atmfBici2Dot0'.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.14.1.3 |
atmIntfActualSideThe current role used by the managed entity to
represent one side of the ATM interface.ro Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.14.1.4 |
atmIntfIlmiFsmStateIndicates the state of the ILMI Finite State Machine
associated with this interface.ro Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.14.1.7 |
atmIntfIlmiEstablishConPollIntvlThe amount of time S between successive transmissions
of ILMI messages on this interface for the purpose of
detecting establishment of ILMI connectivity.rw Integer32 -- SYNTAX Integer32 .1.3.6.1.4.1.42.1.2.1.14.1.14.1.8 |
atmIntfIlmiCheckConPollIntvlThe amount of time T between successive transmissions
of ILMI messages on this interface for the purpose of
detecting loss of ILMI connectivity. The distinguished
value zero disables ILMI connectivity procedures on
this interface.rw Integer32 -- SYNTAX Integer32 .1.3.6.1.4.1.42.1.2.1.14.1.14.1.9 |
atmIntfIlmiConPollInactFactorThe number K of consecutive polls on this interface
for which no ILMI response message is received before
ILMI connectivity is declared lost.rw Integer32 -- SYNTAX Integer32 .1.3.6.1.4.1.42.1.2.1.14.1.14.1.10 |
atmIntfIlmiPublicPrivateIndctrSpecifies whether this end of the interface is
advertised in ILMI as a device of the `public' or
`private' type.rw Enumeration .1.3.6.1.4.1.42.1.2.1.14.1.14.1.11 |
atmInterfaceConfMaxSvpcVpiThe maximum VPI that the signalling stack on the ATM
interface is configured to support for allocation to
switched virtual path connections.rw INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.14.1.12 |
atmInterfaceCurrentMaxSvpcVpiThe maximum VPI that the signalling stack on the ATM
interface may currently allocate to switched virtual
path connections. This value is the minimum of
atmInterfaceConfMaxSvpcVpi, and the
atmInterfaceMaxSvpcVpi of the interface's UNI/NNI peer.
If the interface does not negotiate with its peer to
determine the maximum VPI that can be allocated to
SVPCs on the interface, then the value of this object
must equal atmInterfaceConfMaxSvpcVpi.ro INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.14.1.13 |
atmInterfaceConfMaxSvccVpiThe maximum VPI that the signalling stack on the ATM
interface is configured to support for allocation to
switched virtual channel connections.rw INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.14.1.14 |
atmInterfaceCurrentMaxSvccVpiThe maximum VPI that the signalling stack on the ATM
interface may currently allocate to switched virtual
channel connections. This value is the minimum of
atmInterfaceConfMaxSvccVpi, and the
atmInterfaceConfMaxSvccVpi of the interface's UNI/NNI
peer.
If the interface does not negotiate with its peer to
determine the maximum VPI that can be allocated to
SVCCs on the interface, then the value of this object
must equal atmInterfaceConfMaxSvccVpi.ro INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.14.1.15 |
atmInterfaceConfMinSvccVciThe minimum VCI that the signalling stack on the ATM
interface is configured to support for allocation to
switched virtual channel connections.rw INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.14.1.16 |
atmInterfaceCurrentMinSvccVciThe minimum VCI that the signalling stack on the ATM
interface may currently allocate to switched virtual
channel connections. This value is the maximum of
atmInterfaceConfMinSvccVci, and the
atmInterfaceConfMinSvccVci of the interface's UNI/NNI
peer.
If the interface does not negotiate with its peer to
determine the minimum VCI that can be allocated to
SVCCs on the interface, then the value of this object
must equal atmInterfaceConfMinSvccVci.ro INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.14.1.17 |
atmIntfSigVccRxTrafficDescrIndexThis object identifies the row in the
atmTrafficDescrParamTable used during ILMI
auto-configuration to specify the advertised
signalling VCC traffic parameters for the
receive direction.
The traffic descriptor resulting from ILMI auto-
configuration of the signalling VCC is indicated
in the atmVclTable.rw AtmTrafficDescrParamIndex -- Rsyntax INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.14.1.18 |
atmIntfSigVccTxTrafficDescrIndexThis object identifies the row in the
atmTrafficDescrParamTable used during ILMI
auto-configuration to specify the advertised
signalling VCC traffic parameters for the
transmit direction.
The traffic descriptor resulting from ILMI auto-
configuration of the signalling VCC is indicated
in the atmVclTable.rw AtmTrafficDescrParamIndex -- Rsyntax INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.14.1.19 |
atmIntfPvcFailuresThe number of times the operational status of a PVPL
or PVCL on this interface has gone down.ro Counter32 .1.3.6.1.4.1.42.1.2.1.14.1.14.1.20 |
atmIntfCurrentlyFailingPVplsThe current number of VPLs on this interface for which
there is an active row in the atmVplTable having an
atmVplConnKind value of `pvc' and an atmVplOperStatus
with a value other than `up'.ro Gauge32 .1.3.6.1.4.1.42.1.2.1.14.1.14.1.21 |
atmIntfCurrentlyFailingPVclsThe current number of VCLs on this interface for which
there is an active row in the atmVclTable having an
atmVclConnKind value of `pvc' and an atmVclOperStatus
with a value other than `up'.ro Gauge32 .1.3.6.1.4.1.42.1.2.1.14.1.14.1.22 |
atmIntfPvcFailuresTrapEnableAllows the generation of traps in response to PVCL or
PVPL failures on this interface.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.42.1.2.1.14.1.14.1.23 |
atmIntfPvcNotificationIntervalThe minimum interval between the sending of
atmIntfPvcFailuresTrap notifications for this
interface.rw INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.14.1.24 |
atmIlmiSrvcRegTableThis table contains a list of all the ATM network
services known by this device.
The characteristics of these services are made
available through the ILMI, using the ILMI general-
purpose service registry MIB.
These services may be made available to all ATM
interfaces (atmIlmiSrvcRegIndex = 0) or to some
specific ATM interfaces only (atmIlmiSrvcRegIndex = ATM
interface index). SEQUENCE OF AtmIlmiSrvcRegEntry .1.3.6.1.4.1.42.1.2.1.14.1.15 |
atmIlmiSrvcRegEntryInformation about a single service provider that is
available to the user-side of an adjacent device
through the ILMI. AtmIlmiSrvcRegEntry .1.3.6.1.4.1.42.1.2.1.14.1.15.1 |
atmIlmiSrvcRegIndexThe ATM interface where the service defined in this
entry can be made available to an ATM device attached
to this interface.
The value of 0 has a special meaning: when an ATM
service is defined in an entry whose
atmIlmiSrvcRegIndex is zero, the ATM service is
available to ATM devices connected to any ATM
interface. (default value(s)).
When the user-side of an adjacent device queries the
content of the ILMI service registry MIB (using the
ILMI protocol), the local network-side responds with
the ATM services defined in atmIlmiSrvcRegTable
entries, provided that these entries are indexed by:
- the corresponding interface number (atmIlmiSrvcRegIndex equal
to the number of the interface that the adjacent device is
connected to)
- zero (atmIlmiSrvcRegIndex=0). InterfaceIndex -- Rsyntax Integer32 .1.3.6.1.4.1.42.1.2.1.14.1.15.1.1 |
atmIlmiSrvcRegServiceIDThis is the service identifier which uniquely
identifies the type of service at the address provided
in the table. The object identifiers for the LAN
Emulation Configuration Server (LECS) and the ATM Name
Server (ANS) are defined in the ATM Forum ILMI Service
Registry MIB. OBJECT IDENTIFIER .1.3.6.1.4.1.42.1.2.1.14.1.15.1.2 |
atmIlmiSrvcRegAddressIndexAn arbitrary integer to differentiate multiple rows
containing different ATM addresses for the same service
on the same interface. This number needs NOT to be the
same as the corresponding ILMI atmfSrvcRegAddressIndex
MIB object. INTEGER .1.3.6.1.4.1.42.1.2.1.14.1.15.1.3 |
atmIlmiSrvcRegATMAddressThis is the full address of the service. The user-side of the
adjacent device may use this address to establish a connection
with the service.rw AtmAddr -- Rsyntax OCTET STRING .1.3.6.1.4.1.42.1.2.1.14.1.15.1.4 |
atmIlmiSrvcRegParm1An octet string used according to the value of
atmIlmiSrvcRegServiceID.rw OCTET STRING .1.3.6.1.4.1.42.1.2.1.14.1.15.1.5 |
atmIlmiSrvcRegRowStatusThis object is used to create or destroy an entry from
this table.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.4.1.42.1.2.1.14.1.15.1.6 |
atmIlmiNetworkPrefixTableA table specifying per interface network prefix(es)
supplied by the network side of the UNI during ILMI
address registration. When no network prefixes are
specified for a particular interface, one or more
network prefixes based on the switch address(es) may be
used for ILMI address registration. SEQUENCE OF AtmIlmiNetworkPrefixEntry .1.3.6.1.4.1.42.1.2.1.14.1.16 |
atmIlmiNetworkPrefixEntryInformation about a single network prefix supplied by
the network side of the UNI during ILMI address
registration. Note that the index variable
atmIlmiNetPrefixPrefix is a variable-length string, and
as such the rule for variable-length strings in section
7.7 of RFC 1902 applies. AtmIlmiNetworkPrefixEntry .1.3.6.1.4.1.42.1.2.1.14.1.16.1 |
atmIlmiNetPrefixPrefixThe network prefix specified for use in ILMI address
registration. AtmIlmiNetworkPrefix -- Rsyntax OCTET STRING .1.3.6.1.4.1.42.1.2.1.14.1.16.1.1 |
atmIlmiNetPrefixRowStatusUsed to create, delete, activate and de-activate
network prefixes used in ILMI address registration.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.4.1.42.1.2.1.14.1.16.1.2 |
atmSwitchAddressTableThis table contains one or more ATM endsystem
addresses on a per switch basis. These addresses are
used to identify the switch. When no ILMI network
prefixes are configured for certain interfaces, network
prefixes based on the switch address(es) may be used
for ILMI address registration. SEQUENCE OF AtmSwitchAddressEntry .1.3.6.1.4.1.42.1.2.1.14.1.17 |
atmSwitchAddressEntryAn entry in the ATM Switch Address table. AtmSwitchAddressEntry .1.3.6.1.4.1.42.1.2.1.14.1.17.1 |
atmSwitchAddressIndexAn arbitrary index used to enumerate the ATM endsystem
addresses for this switch. Integer32 -- SYNTAX Integer32 .1.3.6.1.4.1.42.1.2.1.14.1.17.1.1 |
atmSwitchAddressAddressAn ATM endsystem address or address prefix used to
identify this switch. When no ESI or SEL field is
specified, the switch may generate the ESI and SEL
fields automatically to obtain a complete 20-byte ATM
endsystem address.rw OCTET STRING .1.3.6.1.4.1.42.1.2.1.14.1.17.1.2 |
atmSwitchAddressRowStatusUsed to create, delete, activate, and de-
activate
addresses used to identify this switch.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.4.1.42.1.2.1.14.1.17.1.3 |
atmVpCrossConnectXTableThis table contains one row per VP Cross Connect
represented in the atmVpCrossConnectTable. SEQUENCE OF AtmVpCrossConnectXEntry .1.3.6.1.4.1.42.1.2.1.14.1.18 |
atmVpCrossConnectXEntryInformation about a particular ATM VP Cross Connect.
Each entry provides an two objects that name the Cross
Connect. One is assigned by the Service User and the
other by the Service Provider. AtmVpCrossConnectXEntry .1.3.6.1.4.1.42.1.2.1.14.1.18.1 |
atmVpCrossConnectUserNameThis is a service user assigned textual representation
of a VPC PVC.rw DisplayString -- Rsyntax OCTET STRING .1.3.6.1.4.1.42.1.2.1.14.1.18.1.1 |
atmVpCrossConnectProviderNameThis is a system supplied textual representation of
VPC PVC. It is assigned by the service provider.ro DisplayString -- Rsyntax OCTET STRING .1.3.6.1.4.1.42.1.2.1.14.1.18.1.2 |
atmVcCrossConnectXTableThis table contains one row per VC Cross Connect
represented in the atmVcCrossConnectTable. SEQUENCE OF AtmVcCrossConnectXEntry .1.3.6.1.4.1.42.1.2.1.14.1.19 |
atmVcCrossConnectXEntryInformation about a particular ATM VC Cross Connect.
Each entry provides an two objects that name the Cross
Connect. One is assigned by the Service User and the
other by the Service Provider. AtmVcCrossConnectXEntry .1.3.6.1.4.1.42.1.2.1.14.1.19.1 |
atmVcCrossConnectUserNameThis is a service user assigned textual representation
of a VCC PVC.rw DisplayString -- Rsyntax OCTET STRING .1.3.6.1.4.1.42.1.2.1.14.1.19.1.1 |
atmVcCrossConnectProviderNameThis is a system supplied textual representation of
VCC PVC. It is assigned by the service provider.ro DisplayString -- Rsyntax OCTET STRING .1.3.6.1.4.1.42.1.2.1.14.1.19.1.2 |
atmCurrentlyFailingPVplTableA table indicating all VPLs for which there is an
active row in the atmVplTable having an atmVplConnKind
value of `pvc' and an atmVplOperStatus with a value
other than `up'. SEQUENCE OF AtmCurrentlyFailingPVplEntry .1.3.6.1.4.1.42.1.2.1.14.1.20 |
atmCurrentlyFailingPVplEntryEach entry in this table represents a VPL for which
the atmVplRowStatus is `active', the atmVplConnKind is
`pvc', and the atmVplOperStatus is other than `up'. AtmCurrentlyFailingPVplEntry .1.3.6.1.4.1.42.1.2.1.14.1.20.1 |
atmCurrentlyFailingPVplTimeStampThe time at which this PVPL began to fail.ro TimeStamp -- Rsyntax TimeTicks .1.3.6.1.4.1.42.1.2.1.14.1.20.1.1 |
atmCurrentlyFailingPVclTableA table indicating all VCLs for which there is an
active row in the atmVclTable having an atmVclConnKind
value of `pvc' and an atmVclOperStatus with a value
other than `up'. SEQUENCE OF AtmCurrentlyFailingPVclEntry .1.3.6.1.4.1.42.1.2.1.14.1.21 |
atmCurrentlyFailingPVclEntryEach entry in this table represents a VCL for which
the atmVclRowStatus is `active', the atmVclConnKind is
`pvc', and the atmVclOperStatus is other than `up'. AtmCurrentlyFailingPVclEntry .1.3.6.1.4.1.42.1.2.1.14.1.21.1 |
atmCurrentlyFailingPVclTimeStampThe time at which this PVCL began to fail.ro TimeStamp -- Rsyntax TimeTicks .1.3.6.1.4.1.42.1.2.1.14.1.21.1.1 |
atm2MIBTraps OBJECT IDENTIFIER .1.3.6.1.4.1.42.1.2.1.14.2 |
atmPvcTraps OBJECT IDENTIFIER .1.3.6.1.4.1.42.1.2.1.14.2.1 |
atmPvcTrapsPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.42.1.2.1.14.2.1.0 |
atmIntfPvcFailuresTrapA notification indicating that one or more PVPLs or
PVCLs on this interface has failed since the last
atmPvcFailuresTrap was sent. If this trap has not been
sent for the last atmIntfPvcNotificationInterval, then
it will be sent on the next increment of
atmIntfPvcFailures. TRAP-TYPE .1.3.6.1.4.1.42.1.2.1.14.2.1.0.1 |
atm2MIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.42.1.2.1.14.3 |
atm2MIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.42.1.2.1.14.3.1 |
atmSwitchServcHostGroup OBJECT IDENTIFIER .1.3.6.1.4.1.42.1.2.1.14.3.1.1 |
atmSwitchServcGroup OBJECT IDENTIFIER .1.3.6.1.4.1.42.1.2.1.14.3.1.2 |
atmServcGroup OBJECT IDENTIFIER .1.3.6.1.4.1.42.1.2.1.14.3.1.4 |
atmHostGroup OBJECT IDENTIFIER .1.3.6.1.4.1.42.1.2.1.14.3.1.5 |
atm2MIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.42.1.2.1.14.3.2 |
atm2MIBCompliance OBJECT IDENTIFIER .1.3.6.1.4.1.42.1.2.1.14.3.2.1 |