ATM-RMON-MIB
The ATM-RMON-MIB enables remote monitoring of Asynchronous Transfer Mode (ATM) network interfaces and virtual circuits by aggregating traffic statistics, error counters, and performance metrics for analysis via SNMP. It facilitates the collection of granular data on ATM cell loss, cell delay, and connection states to support fault isolation and capacity planning in legacy ATM infrastructure.
Imported Objects
Objects
121 total| Object Name |
|---|
atmRmon MODULE-IDENTITY .1.3.6.1.4.1.9.10.16 |
atmRmonMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.16.1 |
portSelect OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.16.1.1 |
portSelGrpTable SEQUENCE OF PortSelGrpEntry .1.3.6.1.4.1.9.10.16.1.1.1 |
portSelGrpEntry PortSelGrpEntry .1.3.6.1.4.1.9.10.16.1.1.1.1 |
portSelGrpIndex Integer32 .1.3.6.1.4.1.9.10.16.1.1.1.1.1 |
portSelGrpDescrrw DisplayString .1.3.6.1.4.1.9.10.16.1.1.1.1.2 |
portSelGrpCreateTimero LastCreateTime .1.3.6.1.4.1.9.10.16.1.1.1.1.3 |
portSelGrpOwnerrw OwnerString (IF-MIB) .1.3.6.1.4.1.9.10.16.1.1.1.1.4 |
portSelGrpStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.10.16.1.1.1.1.5 |
portSelTable SEQUENCE OF PortSelEntry .1.3.6.1.4.1.9.10.16.1.1.2 |
portSelEntry PortSelEntry .1.3.6.1.4.1.9.10.16.1.1.2.1 |
portSelCollectGrouprw Integer32 .1.3.6.1.4.1.9.10.16.1.1.2.1.1 |
portSelCreateTimero LastCreateTime .1.3.6.1.4.1.9.10.16.1.1.2.1.2 |
portSelOwnerrw OwnerString (IF-MIB) .1.3.6.1.4.1.9.10.16.1.1.2.1.3 |
portSelStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.10.16.1.1.2.1.4 |
atmStats OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.16.1.2 |
atmStatsControlTable SEQUENCE OF AtmStatsControlEntry .1.3.6.1.4.1.9.10.16.1.2.1 |
atmStatsControlEntry AtmStatsControlEntry .1.3.6.1.4.1.9.10.16.1.2.1.1 |
atmStatsControlDropEventsro Counter32 .1.3.6.1.4.1.9.10.16.1.2.1.1.1 |
atmStatsControlOwnerrw OwnerString (IF-MIB) .1.3.6.1.4.1.9.10.16.1.2.1.1.2 |
atmStatsControlStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.10.16.1.2.1.1.3 |
atmStatsTable SEQUENCE OF AtmStatsEntry .1.3.6.1.4.1.9.10.16.1.2.2 |
atmStatsEntry AtmStatsEntry .1.3.6.1.4.1.9.10.16.1.2.2.1 |
atmStatsSClass ServiceClass .1.3.6.1.4.1.9.10.16.1.2.2.1.1 |
atmStatsCreateTimero LastCreateTime .1.3.6.1.4.1.9.10.16.1.2.2.1.2 |
atmStatsCellsro Counter32 .1.3.6.1.4.1.9.10.16.1.2.2.1.3 |
atmStatsCellsRolloversro Counter32 .1.3.6.1.4.1.9.10.16.1.2.2.1.4 |
atmStatsHCCellsro Counter64 .1.3.6.1.4.1.9.10.16.1.2.2.1.5 |
atmStatsNumCallAttemptsro Counter32 .1.3.6.1.4.1.9.10.16.1.2.2.1.6 |
atmStatsNumCallsro Counter32 .1.3.6.1.4.1.9.10.16.1.2.2.1.7 |
atmStatsConnTimero ConnectTime UNITS "seconds" .1.3.6.1.4.1.9.10.16.1.2.2.1.8 |
atmHost OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.16.1.3 |
atmHostControlTable SEQUENCE OF AtmHostControlEntry .1.3.6.1.4.1.9.10.16.1.3.1 |
atmHostControlEntry AtmHostControlEntry .1.3.6.1.4.1.9.10.16.1.3.1.1 |
atmHostControlInsertsro Counter32 .1.3.6.1.4.1.9.10.16.1.3.1.1.1 |
atmHostControlDeletesro Counter32 .1.3.6.1.4.1.9.10.16.1.3.1.1.2 |
atmHostControlMaxDesiredEntriesrw Integer32 .1.3.6.1.4.1.9.10.16.1.3.1.1.3 |
atmHostControlPriorityrw ResourcePriority .1.3.6.1.4.1.9.10.16.1.3.1.1.4 |
atmHostControlAddrCollectScoperw AddressCollectScope .1.3.6.1.4.1.9.10.16.1.3.1.1.5 |
atmHostControlDropEventsro Counter32 .1.3.6.1.4.1.9.10.16.1.3.1.1.6 |
atmHostControlOwnerrw OwnerString (IF-MIB) .1.3.6.1.4.1.9.10.16.1.3.1.1.7 |
atmHostControlStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.10.16.1.3.1.1.8 |
atmHostTable SEQUENCE OF AtmHostEntry .1.3.6.1.4.1.9.10.16.1.3.2 |
atmHostEntry AtmHostEntry .1.3.6.1.4.1.9.10.16.1.3.2.1 |
atmHostAddress AtmAddr .1.3.6.1.4.1.9.10.16.1.3.2.1.1 |
atmHostSClass ServiceClass .1.3.6.1.4.1.9.10.16.1.3.2.1.2 |
atmHostCreateTimero LastCreateTime .1.3.6.1.4.1.9.10.16.1.3.2.1.3 |
atmHostInCellsro ZeroBasedCounter32 .1.3.6.1.4.1.9.10.16.1.3.2.1.4 |
atmHostInCellsRolloversro ZeroBasedCounter32 .1.3.6.1.4.1.9.10.16.1.3.2.1.5 |
atmHostInHCCellsro Counter64 .1.3.6.1.4.1.9.10.16.1.3.2.1.6 |
atmHostOutCellsro ZeroBasedCounter32 .1.3.6.1.4.1.9.10.16.1.3.2.1.7 |
atmHostOutCellsRolloversro ZeroBasedCounter32 .1.3.6.1.4.1.9.10.16.1.3.2.1.8 |
atmHostOutHCCellsro Counter64 .1.3.6.1.4.1.9.10.16.1.3.2.1.9 |
atmHostInNumCallAttemptsro ZeroBasedCounter32 .1.3.6.1.4.1.9.10.16.1.3.2.1.10 |
atmHostInNumCallsro ZeroBasedCounter32 .1.3.6.1.4.1.9.10.16.1.3.2.1.11 |
atmHostOutNumCallAttemptsro ZeroBasedCounter32 .1.3.6.1.4.1.9.10.16.1.3.2.1.12 |
atmHostOutNumCallsro ZeroBasedCounter32 .1.3.6.1.4.1.9.10.16.1.3.2.1.13 |
atmHostInConnTimero ConnectTime UNITS "seconds" .1.3.6.1.4.1.9.10.16.1.3.2.1.14 |
atmHostOutConnTimero ConnectTime UNITS "seconds" .1.3.6.1.4.1.9.10.16.1.3.2.1.15 |
atmMatrix OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.16.1.4 |
atmMatrixControlTable SEQUENCE OF AtmMatrixControlEntry .1.3.6.1.4.1.9.10.16.1.4.1 |
atmMatrixControlEntry AtmMatrixControlEntry .1.3.6.1.4.1.9.10.16.1.4.1.1 |
atmMatrixControlInsertsro Counter32 .1.3.6.1.4.1.9.10.16.1.4.1.1.1 |
atmMatrixControlDeletesro Counter32 .1.3.6.1.4.1.9.10.16.1.4.1.1.2 |
atmMatrixControlMaxDesiredEntriesrw Integer32 .1.3.6.1.4.1.9.10.16.1.4.1.1.3 |
atmMatrixControlPriorityrw ResourcePriority .1.3.6.1.4.1.9.10.16.1.4.1.1.4 |
atmMatrixControlAddrCollectScoperw AddressCollectScope .1.3.6.1.4.1.9.10.16.1.4.1.1.5 |
atmMatrixControlDropEventsro Counter32 .1.3.6.1.4.1.9.10.16.1.4.1.1.6 |
atmMatrixControlOwnerrw OwnerString (IF-MIB) .1.3.6.1.4.1.9.10.16.1.4.1.1.7 |
atmMatrixControlStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.10.16.1.4.1.1.8 |
atmMatrixSDTable SEQUENCE OF AtmMatrixSDEntry .1.3.6.1.4.1.9.10.16.1.4.2 |
atmMatrixSDEntry AtmMatrixSDEntry .1.3.6.1.4.1.9.10.16.1.4.2.1 |
atmMatrixSDSrcAddress AtmAddr .1.3.6.1.4.1.9.10.16.1.4.2.1.1 |
atmMatrixSDDstAddress AtmAddr .1.3.6.1.4.1.9.10.16.1.4.2.1.2 |
atmMatrixSDSClass ServiceClass .1.3.6.1.4.1.9.10.16.1.4.2.1.3 |
atmMatrixSDCreateTimero LastCreateTime .1.3.6.1.4.1.9.10.16.1.4.2.1.4 |
atmMatrixSDCellsro ZeroBasedCounter32 .1.3.6.1.4.1.9.10.16.1.4.2.1.5 |
atmMatrixSDCellsRolloversro ZeroBasedCounter32 .1.3.6.1.4.1.9.10.16.1.4.2.1.6 |
atmMatrixSDHCCellsro Counter64 .1.3.6.1.4.1.9.10.16.1.4.2.1.7 |
atmMatrixSDNumCallAttemptsro ZeroBasedCounter32 .1.3.6.1.4.1.9.10.16.1.4.2.1.8 |
atmMatrixSDNumCallsro ZeroBasedCounter32 .1.3.6.1.4.1.9.10.16.1.4.2.1.9 |
atmMatrixSDConnTimero ConnectTime UNITS "seconds" .1.3.6.1.4.1.9.10.16.1.4.2.1.10 |
atmMatrixDSTable SEQUENCE OF AtmMatrixDSEntry .1.3.6.1.4.1.9.10.16.1.4.3 |
atmMatrixDSEntry AtmMatrixDSEntry .1.3.6.1.4.1.9.10.16.1.4.3.1 |
atmMatrixDSSrcAddress AtmAddr .1.3.6.1.4.1.9.10.16.1.4.3.1.1 |
atmMatrixDSDstAddress AtmAddr .1.3.6.1.4.1.9.10.16.1.4.3.1.2 |
atmMatrixDSSClass ServiceClass .1.3.6.1.4.1.9.10.16.1.4.3.1.3 |
atmMatrixDSCreateTimero LastCreateTime .1.3.6.1.4.1.9.10.16.1.4.3.1.4 |
atmMatrixDSCellsro ZeroBasedCounter32 .1.3.6.1.4.1.9.10.16.1.4.3.1.5 |
atmMatrixDSCellsRolloversro ZeroBasedCounter32 .1.3.6.1.4.1.9.10.16.1.4.3.1.6 |
atmMatrixDSHCCellsro Counter64 .1.3.6.1.4.1.9.10.16.1.4.3.1.7 |
atmMatrixDSNumCallAttemptsro ZeroBasedCounter32 .1.3.6.1.4.1.9.10.16.1.4.3.1.8 |
atmMatrixDSNumCallsro ZeroBasedCounter32 .1.3.6.1.4.1.9.10.16.1.4.3.1.9 |
atmMatrixDSConnTimero ConnectTime UNITS "seconds" .1.3.6.1.4.1.9.10.16.1.4.3.1.10 |
atmMatrixTopNControlTable SEQUENCE OF AtmMatrixTopNControlEntry .1.3.6.1.4.1.9.10.16.1.4.4 |
atmMatrixTopNControlEntry AtmMatrixTopNControlEntry .1.3.6.1.4.1.9.10.16.1.4.4.1 |
atmMatrixTopNControlIndex Integer32 .1.3.6.1.4.1.9.10.16.1.4.4.1.1 |
atmMatrixTopNControlRateBaserw Enumeration .1.3.6.1.4.1.9.10.16.1.4.4.1.2 |
atmMatrixTopNControlSClassrw ServiceClass .1.3.6.1.4.1.9.10.16.1.4.4.1.3 |
ATM-RMON-MIB Technical Reference Overview
The ATM-RMON-MIB SNMP MIB module published by Cisco defines 121 managed OID objects, including 88 scalar/column metrics, 11 SNMP tables, and 0 trap/notification events anchored at base OID .1.3.6.1.4.1.9.10.16. Key tabular structures include portSelGrpTable, portSelTable, atmStatsControlTable, atmStatsTable, atmHostControlTable, atmHostTable.
Key OID Definitions in ATM-RMON-MIB
.1.3.6.1.4.1.9.10.16The MIB module for managing remote monitoring device implementations for ATM networks.
.1.3.6.1.4.1.9.10.16.1.1.1Controls the setup of port and ATM connection selection criteria used on behalf of any collection associated with entries in this table (e.g., atmHostTable). This table allows portSelTable entries with the same value of the portSelCollectGroup object to be grouped together to form port select groups. Note that an agent implementation may restrict the actual number of portSelGrp entries, due to resource limitations.
.1.3.6.1.4.1.9.10.16.1.1.2Controls the setup of selection criteria for a single ATM port, used on behalf of any collections identified with the associated portSelectGroup (identified by its portSelGrpIndex value). This table identifies the collection characteristics for the ATM port indicated by the ifIndex value in the index. Note that an agent implementation may restrict the actual number of portSelTable entries, due to resource limitations.
.1.3.6.1.4.1.9.10.16.1.2.1A list of ATM basic statistic collection table control entries. These entries will enable the collection of statistical totals for an entire portSelectGroup.
.1.3.6.1.4.1.9.10.16.1.2.2A collection of statistical totals for all ATM addresses that have been discovered on behalf of the portSelectGroup associated with this entry.
.1.3.6.1.4.1.9.10.16.1.3.1A list of ATM host table control entries. These entries will enable the collection of ATM host information in the atmHostTable. Entries in the atmHostTable will be created on behalf of each entry in this table. A probe is required to support at most one atmHost collection per instance of an associated portSelectGroup, therefore the table is indexed by the portSelGrpIndex.
.1.3.6.1.4.1.9.10.16.1.3.2A collection of statistics for a particular ATM host address that has been discovered on behalf of the portSelectGroup associated with this entry. The probe will add to this table all addresses seen as the source or destination address in all calls, on all ports configured in the portSelGrpEntry controlling this collection.
.1.3.6.1.4.1.9.10.16.1.4.1A list of ATM matrix table control entries. These entries will enable the collection of ATM matrix information in the atmMatrixSDTable and atmMatrixDSTable. A probe is required to support at most one atmMatrix collection per instance of an associated portSelectGroup, therefore the table is indexed by the portSelGrpIndex.
.1.3.6.1.4.1.9.10.16.1.4.2A collection of statistics for conversations between particular ATM endpoint addresses that have been discovered on behalf of the portSelectGroup associated with this entry. The probe will add a new entry to this table for all conversations (connections) between distinct source and destination address pairs, detected in all calls, on all ports configured in the portSelGrpEntry controlling this collection. Further, this table will only contain entries that have a corresponding entry in the atmMatrixDSTable with the same source address and destination address.
.1.3.6.1.4.1.9.10.16.1.4.3A collection of statistics for conversations between particular ATM endpoint addresses that have been discovered on behalf of the portSelectGroup associated with this entry. The probe will add a new entry to this table for all conversations (connections) between distinct source and destination address pairs, detected in all cells identified by the associated portSelGrpEntry criteria. Further, this table will only contain entries that have a corresponding entry in the atmMatrixSDTable with the same source address and destination address.
.1.3.6.1.4.1.9.10.16.1.4.4A set of parameters that control the creation of a report of the top N matrix entries according to a selected metric.
.1.3.6.1.4.1.9.10.16.1.4.5A set of statistics for those matrix entries that have counted the highest number of cells, calls, or connection time.
.1.3.6.1.4.1.9.10.16.1.5.1Controls the internal data collection for the entire ATM-RMON agent. If this object has a value of 'active(1)', then data tables will be created and maintained (normal behavior). If this object has a value of 'inactive(2)' then ATM-RMON monitoring will not occur, even if valid control tables exist for particular collections. Data tables for active collections are deleted when this object is changed to 'inactive(2)', but control tables are not deleted. When this object is changed to 'active(1)', data collection is started for all valid control tables.
.1.3.6.1.4.1.9.10.16.1.1.1.1A conceptual row in the portSelGrpTable. An example of the indexing of this entry is portSelGrpCreateTime.7 .
.1.3.6.1.4.1.9.10.16.1.1.1.1.1An arbitrary and unique index for this portSelGrpEntry. If portSelGrpTable entries are recreated by the agent after a restart, then the portSelGrpIndex value must be retained across a restart as well.
.1.3.6.1.4.1.9.10.16.1.1.1.1.2An administratively-assigned descriptive label for this portSelGrp entry.
.1.3.6.1.4.1.9.10.16.1.1.1.1.3The value of sysUpTime when this portSelGrp entry was activated. This can be used by the management station to ensure that the table has not been deleted and recreated between polls.
.1.3.6.1.4.1.9.10.16.1.1.1.1.4The entity that configured this entry and is therefore using the resources assigned to it.
.1.3.6.1.4.1.9.10.16.1.1.1.1.5The status of this row. An entry may not exist in the active state unless all objects in the entry have an appropriate value. No objects are required to be written prior to the row being set to active(1). However, all portSelTable entries which are to be included in collections on behalf of this portSelectGroup, must be completely configured and activated before this object is set to active(1), since the associated instances of portSelStatus cannot be modified once this object has been set to active(1). If this object is not equal to active(1), all associated data collections shall be deleted (e.g., any associated collections in the atmStats, atmHostTable or atmMatrixSDTable). Note that associated portSelTable and any configured collection control entries (e.g., atmHostControlTable) are not deleted when this entry leaves the active state.
.1.3.6.1.4.1.9.10.16.1.1.2.1A conceptual row in the portSelTable. Entries may only be created on behalf of ATM interfaces. That is, the ifType value associated with each ifIndex value must be equal to atm(37) or atmLogicalPort(80). An example of the indexing of this entry is portSelCreateTime.7 .
.1.3.6.1.4.1.9.10.16.1.1.2.1.1This object identifies the associated instance of portSelGrpIndex, which indicates the portSelectGroup to which this port is assigned. This object may not be modified if the associated instance of portSelStatus is equal to active(1).
.1.3.6.1.4.1.9.10.16.1.1.2.1.2The value of sysUpTime when this entry was activated. This can be used by the management station to ensure that the table has not been deleted and recreated between polls.
.1.3.6.1.4.1.9.10.16.1.1.2.1.3The entity that configured this entry and is therefore using the resources assigned to it.
.1.3.6.1.4.1.9.10.16.1.1.2.1.4The status of this row. An entry may not exist in the active state unless all objects in the entry have an appropriate value. Specifically, an appropriate value for the portSelCollectGroup object must be set before this object may be set to active(1). An agent may wish to allow portSelTable entries to exist which reference non-existent portSelGrpTable entries, in order to reduce row creation order dependencies. All portSelTable entries which are to be included in a particular collection (as indicated by the portSelCollectGroup object), should be completely configured and activated before the associated portSelGrpStatus object is set to active(1). Configuration of a portSelectGroup cannot be modified once collections on its behalf have been started. This object may not be modified if the associated portSelGroupStatus in in the active(1) state, indicated by a portSelGrpIndex value identical to the value of the portSelCollectGroup object in this entry.
More MIBs from Cisco
Browse all CiscoMIBs →The CISCO-UNIFIED-COMPUTING-COMPUTE-MIB provides SNMP-based monitoring and management of Cisco UCS compute blades, servers, and chassis components, exposing critical metrics such as CPU utilization, memory usage, thermal sensor readings, power supply status, and interface operational states. This module enables granular visibility into the health and performance of the Cisco Unified Computing System's compute subsystems for capacity planning and fault isolation.
The CISCO-UNIFIED-COMPUTING-STORAGE-MIB facilitates SNMP-based monitoring and management of storage subsystems, including Fibre Channel and iSCSI interfaces, within the Cisco Unified Computing System (UCS) fabric interconnects and blade servers. It exposes critical operational metrics such as port status, error counters, throughput statistics, and storage controller health states to enable granular visibility into the storage infrastructure.
The CISCO-UNIFIED-COMPUTING-VNIC-MIB enables SNMP-based monitoring and management of Virtual Network Interface Card (vNIC) attributes, including operational status, traffic counters, and binding configurations, within the Cisco Unified Computing System (UCS) fabric interconnects and server blades.
SNMP MIB module
The CISCO-UNIFIED-COMPUTING-BIOS-MIB enables SNMP-based monitoring and configuration of BIOS-level parameters, firmware versions, and hardware initialization states within Cisco Unified Computing System (UCS) servers. It provides visibility into critical server boot diagnostics, BIOS settings, and hardware readiness indicators to facilitate low-level infrastructure management and troubleshooting.
The CISCO-UNIFIED-COMPUTING-ETHER-MIB provides SNMP management interfaces for monitoring Ethernet interface statistics, link states, and error counters on Cisco Unified Computing System (UCS) fabric interconnects and blade server line cards. This module enables the tracking of physical layer connectivity, port throughput, and packet error rates within the UCS Ethernet switching infrastructure.