ATI-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
224
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
224 total| Object Name |
|---|
alliedTelesyn OBJECT IDENTIFIER .1.3.6.1.4.1.207 |
products OBJECT IDENTIFIER .1.3.6.1.4.1.207.1 |
bridge OBJECT IDENTIFIER .1.3.6.1.4.1.207.1.1 |
atiBridgeagent OBJECT IDENTIFIER .1.3.6.1.4.1.207.1.1.1 |
bridgesnmpd OBJECT IDENTIFIER .1.3.6.1.4.1.207.1.1.1.1 |
atiBridge OBJECT IDENTIFIER .1.3.6.1.4.1.207.1.1.1.1.1 |
repeater OBJECT IDENTIFIER .1.3.6.1.4.1.207.1.2 |
intruderProtectionTrapThis trap is replaced by atiIntruderProtectionTrap starting from
firmware ver 3.0.
AT-3100 and TurboStack product families only.
This trap is sent when an Intruder Alert occurs on a port due
to a received packet with an unauthorized source MAC address.
Intruder Protection for the module must be enabled.
The varBind list contains the MAC address of the intruder. TRAP-TYPE .1.3.6.1.4.1.207.1.2.0.20 |
atiIntruderProtectionTrapAT-3100 and TurboStack product families only.
This trap is sent when an Intruder Alert occurs on a module/port due
to a received packet with an unauthorized source MAC address.
Intruder Protection for the module must be enabled.
The varBind list contains the module number, port number,
and the MAC address of the intruder. TRAP-TYPE .1.3.6.1.4.1.207.1.2.0.21 |
atiRedundantPortChangeTrapTurboStack product family only.
This trap is sent when ports, which are configured for
redundant links, change from primary to secondary or
secondary to primary. TRAP-TYPE .1.3.6.1.4.1.207.1.2.0.22 |
hub3600 OBJECT IDENTIFIER .1.3.6.1.4.1.207.1.2.1 |
hub3100 OBJECT IDENTIFIER .1.3.6.1.4.1.207.1.2.10 |
hubTurboStack OBJECT IDENTIFIER .1.3.6.1.4.1.207.1.2.65 |
filterTable OBJECT IDENTIFIER .1.3.6.1.4.1.207.2 |
ftConfigBridge FT operational parameters SEQUENCE OF FtConfig .1.3.6.1.4.1.207.2.1 |
ftMaxAgeSeconds before an unreferenced dynamic FT
entry is removedro INTEGER .1.3.6.1.4.1.207.2.1.1 |
ftMaxRemoveMax number table entries removed each
time table overflowsrw INTEGER .1.3.6.1.4.1.207.2.1.2 |
ftMaxFilterMax number FT entriesro INTEGER .1.3.6.1.4.1.207.2.1.3 |
ftAgeTimeSeconds between FT table entriesrw INTEGER .1.3.6.1.4.1.207.2.1.4 |
ftMaxPermMax number of permanent FT entries. May be set
to zero which causes all non-system FT entries
to be deletedrw INTEGER .1.3.6.1.4.1.207.2.1.5 |
ftForwMBcastFlag indicates if multicast (including broadcast)
packets are to be forwarded (1) or discarded (0)rw Enumeration .1.3.6.1.4.1.207.2.1.6 |
ftSecureModeFlag indicates if bridge will learn addressesrw Enumeration .1.3.6.1.4.1.207.2.1.7 |
ftEntryBridge FT entries each selected by destination
address SEQUENCE OF FtEntry .1.3.6.1.4.1.207.2.2 |
ftAgeFT entry age since last referenced in secondsro INTEGER .1.3.6.1.4.1.207.2.2.1 |
ftDispFT entry disposition. Can be more than one OR'ed togetherrw Enumeration .1.3.6.1.4.1.207.2.2.2 |
ftAddrdestination address (dummy index) OCTET STRING .1.3.6.1.4.1.207.2.2.91 |
interfaceErrorsSet of Ethernet link level errors InterfaceErrors .1.3.6.1.4.1.207.3 |
ifeInBusErrNumber of EtherStar read bus errors that
have occurredro Counter .1.3.6.1.4.1.207.3.1 |
ifeInShortPktNumber of short packets receivedro Counter .1.3.6.1.4.1.207.3.2 |
ifeInAlgErrorNumber of packets received with alignment errorsro Counter .1.3.6.1.4.1.207.3.3 |
ifeInBadSizeNumber of packets received greater than 1518 bytesro Counter .1.3.6.1.4.1.207.3.4 |
ifeInOverflowNumber of times receive buffer overflowedro Counter .1.3.6.1.4.1.207.3.5 |
ifeInCRCErrNumber of CRC errors detectedro Counter .1.3.6.1.4.1.207.3.6 |
ifeOutColl16Number of packets discarded due to excessive
collisionsro Counter .1.3.6.1.4.1.207.3.7 |
ifeOutColNumber of collisions detectedro Counter .1.3.6.1.4.1.207.3.8 |
ifeOutShortPktNumber of short packets transmittedro Counter .1.3.6.1.4.1.207.3.9 |
ifeOutUnderflowNumber of packets transmitted w/programmed
length > buffered transmitted dataro Counter .1.3.6.1.4.1.207.3.10 |
ifeOutBusErrNumber of EtherStar write bus errorsro Counter .1.3.6.1.4.1.207.3.11 |
ifePort Enumeration .1.3.6.1.4.1.207.3.91 |
forwardCountersCounters associated with bridge entityro ForwardCounters .1.3.6.1.4.1.207.4 |
fcInOctetsNumber bytes received by bridge entity on
specified portro Counter .1.3.6.1.4.1.207.4.1 |
fcInPktsNumber packets received by bridge entity on
specified portro Counter .1.3.6.1.4.1.207.4.2 |
fcInNUcastPktsNumber multicast/broadcast packets received by
bridge enity on specified portro Counter .1.3.6.1.4.1.207.4.3 |
fcForwOctetsNumber bytes forwarded by bridge entity onto
specified portro Counter .1.3.6.1.4.1.207.4.4 |
fcForwPktsNumber of packets forwarded by bridge enity
onto specified portro Counter .1.3.6.1.4.1.207.4.5 |
fcFiltOctetsNumber of bytes received on specified port
that were discarded by bridge enityro Counter .1.3.6.1.4.1.207.4.6 |
fcFiltPktsNumber of packets dicarded by filtering by
bridge enityro Counter .1.3.6.1.4.1.207.4.7 |
fcPort INTEGER .1.3.6.1.4.1.207.4.91 |
systemCountersSystem operating s/w countersro SystemCounters .1.3.6.1.4.1.207.5 |
sysMemFreeNumber of buffers of a particular size on
the memory free listro Counter .1.3.6.1.4.1.207.5.1 |
sysMemAllocFailNumber of allocation failures for a particular
buffer sizero Counter .1.3.6.1.4.1.207.5.2 |
sysMemTotAllocFailTotal number of memory allocation failuresro Counter .1.3.6.1.4.1.207.5.3 |
sysMemAllocTooBigNumber of memory allocation requests that failedro Counter .1.3.6.1.4.1.207.5.4 |
sysMemFreeFailNumber of memory free requests that failedro Counter .1.3.6.1.4.1.207.5.5 |
sysTimeToResetNumber of seconds unit bridge resetrw Counter .1.3.6.1.4.1.207.5.6 |
sysPanicMesgError message associated with last s/w
generated resetro OCTET STRING .1.3.6.1.4.1.207.5.7 |
sysResetCountNumber of times bridge has been reset other
than power on/offro Counter .1.3.6.1.4.1.207.5.8 |
spanningTree OBJECT IDENTIFIER .1.3.6.1.4.1.207.6 |
stBridgeBridge specific parameters related to
operation of Spanning Tree Protocol SEQUENCE OF StBridge .1.3.6.1.4.1.207.6.1 |
stBrNameComment string denoting the bridgerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.207.6.1.1 |
stBrIdent802.1 Bridge IDro OCTET STRING .1.3.6.1.4.1.207.6.1.2 |
stBrMaxAge802.1 Max BPDU Age (sec) for bridgerw INTEGER .1.3.6.1.4.1.207.6.1.3 |
stBrHelloTime802.1 Hello Time (sec) for bridgerw INTEGER .1.3.6.1.4.1.207.6.1.4 |
stBrForwDelay802.1 Forward Delay Time (sec) for bridgerw INTEGER .1.3.6.1.4.1.207.6.1.5 |
stBrIsRootBridge is root (1=yes 0=no)ro Enumeration .1.3.6.1.4.1.207.6.1.6 |
stBrIsDesigFlag indicating status of bridge as designated
bridge (1=yes 0=no)ro Enumeration .1.3.6.1.4.1.207.6.1.7 |
stBrSpanAddrMAC address used as Spanning Tree Protocol
multicast addressro OCTET STRING .1.3.6.1.4.1.207.6.1.8 |
stBrPriority802.1 bridge priorityrw INTEGER .1.3.6.1.4.1.207.6.1.9 |
stBrSTPDisabledVariable to enable/disable operation of Spanning
Tree (1=STP on 0=STP off)rw Enumeration .1.3.6.1.4.1.207.6.1.10 |
stRootParameters related to operation of Spanning
Tree Protocol for Root bridge SEQUENCE OF StRoot .1.3.6.1.4.1.207.6.2 |
stRtIdent802.1 Bridge ID of current Root bridgero OCTET STRING .1.3.6.1.4.1.207.6.2.1 |
stRtCost802.1 Root Path Cost of current Root bridgero INTEGER .1.3.6.1.4.1.207.6.2.2 |
stRtPortPort number of port that provides path to
current Root bridgero Enumeration .1.3.6.1.4.1.207.6.2.3 |
stRtMaxAge802.1 Max BPDU Age specified by current known Root bridgero INTEGER .1.3.6.1.4.1.207.6.2.4 |
stRtHelloTime802.1 Hello Time specified by current Root bridgero INTEGER .1.3.6.1.4.1.207.6.2.5 |
stRtForwDelay802.1 Forward Delay specified by current Root
bridgero INTEGER .1.3.6.1.4.1.207.6.2.6 |
stPortPort specific parameters related to operation of
Spanning Tree Protocol SEQUENCE OF StPort .1.3.6.1.4.1.207.6.3 |
stPrtState802.1 Port State disable and blocked statesrw Enumeration .1.3.6.1.4.1.207.6.3.1 |
stPrtCost802.1 Port Path Costrw INTEGER .1.3.6.1.4.1.207.6.3.2 |
stPrtIsDesigStatus of port as designated port for LANro Enumeration .1.3.6.1.4.1.207.6.3.3 |
stPrtIsRootStatus of port as Root Portro Enumeration .1.3.6.1.4.1.207.6.3.4 |
stPrtDesigRootBridge ID of Root brigdero OCTET STRING .1.3.6.1.4.1.207.6.3.5 |
stPrtDesigCostPath Cost to Root bridge as advertised by the designated bridgero INTEGER .1.3.6.1.4.1.207.6.3.6 |
stPrtDesigBridgeBridge ID of designated bridgero INTEGER .1.3.6.1.4.1.207.6.3.7 |
stPrtDesigPortPort ID of designated portro INTEGER .1.3.6.1.4.1.207.6.3.8 |
stPrtPriority802.1 Port Priorityrw INTEGER .1.3.6.1.4.1.207.6.3.9 |
stPrtPort Enumeration .1.3.6.1.4.1.207.6.3.91 |
spanTreeStatsSpanning Tree stats on countersro SEQUENCE OF SpanTreeStats .1.3.6.1.4.1.207.6.4 |
stsTopoChangesNumber of topology changes that have occured
since power-onro Counter .1.3.6.1.4.1.207.6.4.1 |
stsConfigTimeoutNumber of timeouts due to config BPDU not receivedro Counter .1.3.6.1.4.1.207.6.4.2 |
stsPortDisableNumber of times port has been disabled since
power-onro Counter .1.3.6.1.4.1.207.6.4.3 |
stsPortEnableNumber of times port has been enabled since
power-onro Counter .1.3.6.1.4.1.207.6.4.4 |
stsInBadLenNumber of STP frames received with bad lenth
by this portro Counter .1.3.6.1.4.1.207.6.4.5 |
stsInUnknownPackets received with bad 802.3 LSAP number by
this portro Counter .1.3.6.1.4.1.207.6.4.6 |
stsIn8021ManPackets received with 802.1 Management LSAP
(discarded)ro Counter .1.3.6.1.4.1.207.6.4.7 |
stsInConfigNumber of config BPDUs received by this portro Counter .1.3.6.1.4.1.207.6.4.8 |
stsOutConfigNumber of config BPDUs transmitted by this portro Counter .1.3.6.1.4.1.207.6.4.9 |
stsOutTopoChgNumber of Topology Change Notification BPDU
transmitted by this portro Counter .1.3.6.1.4.1.207.6.4.10 |
stsPort INTEGER .1.3.6.1.4.1.207.6.4.91 |
filterRange OBJECT IDENTIFIER .1.3.6.1.4.1.207.7 |
frNumRangeThe maximum number of filter range table entries when
read (GET). Set to zero to delete all filter range
table entries. A set with any other value is ignored.rw INTEGER .1.3.6.1.4.1.207.7.1 |
frEntryrw SEQUENCE OF OCTET STRING .1.3.6.1.4.1.207.7.2 |
frIndex INTEGER .1.3.6.1.4.1.207.7.91 |
mibObject OBJECT IDENTIFIER .1.3.6.1.4.1.207.8 |
hubMib OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.1 |
rptrInfo OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.1.1 |
actualIPAddrThe actual IP Address that is currently being used by the
hub. This could be the same value as hubIPAddr, or it may
be different if another IP Address was received via Bootp.ro IpAddress .1.3.6.1.4.1.207.8.1.1.1 |
hubIPAddrThe configured IP Address of the hub.rw IpAddress .1.3.6.1.4.1.207.8.1.1.2 |
subnetMaskSubnet mask of the hub.rw IpAddress .1.3.6.1.4.1.207.8.1.1.3 |
routerAddrGateway/router address of the hub.rw IpAddress .1.3.6.1.4.1.207.8.1.1.4 |
snmpManagerIP Address of the hub's SNMP manager to which Traps
will be sent.rwdeprecated IpAddress .1.3.6.1.4.1.207.8.1.1.5 |
softwareProductThe ATI software product model number running in the hub.ro DisplayString .1.3.6.1.4.1.207.8.1.1.6 |
softwareLevelThe software release level running in the hub.ro DisplayString .1.3.6.1.4.1.207.8.1.1.7 |
configurationChangedA flag, set to the value changed(1) when any of the
hub's status or configuration has been changed.
When this object is read, then the value is reset
to nochange(2).ro Enumeration .1.3.6.1.4.1.207.8.1.1.8 |
rptrNmMgrTableA list of SNMP Trap Manager stations Entries.
The number of entries is given by the
rptrNmMgrTotal mib object. SEQUENCE OF RptrNmMgrEntry .1.3.6.1.4.1.207.8.1.1.9 |
rptrNmMgrEntryAn Trap receipt Manager Entry containing ipaddress of
the configured NMS's to which Traps are sent. RptrNmMgrEntry .1.3.6.1.4.1.207.8.1.1.9.1 |
rptrNmMgrIndexThe Index of SNMP Managers IP Address.ro INTEGER .1.3.6.1.4.1.207.8.1.1.9.1.1 |
rptrNmMgrIpAddrThe IP Address of the NMS host configured.rw IpAddress .1.3.6.1.4.1.207.8.1.1.9.1.2 |
deviceTableThe table contains the mapping of all devices
in the chassis. For all hubs and switches, the
object 'deviceQuadrant' returns 'right' (1).
For docking devices, then it will reflect the
position of the device in the docking station.
This object is specific to Turbo Stack. SEQUENCE OF DeviceEntry .1.3.6.1.4.1.207.8.1.1.10 |
deviceEntryThe device entry in the DeviceTable. DeviceEntry .1.3.6.1.4.1.207.8.1.1.10.1 |
deviceIndexThe Slot number in the chassis where the device is
installed.ro INTEGER .1.3.6.1.4.1.207.8.1.1.10.1.1 |
deviceQuadrantThe Quadrant of the device.ro Enumeration .1.3.6.1.4.1.207.8.1.1.10.1.2 |
deviceDescrTurboStack product family only.
A textual description of the device.
For devices that are repeaters, this value is identical to
the rptrGroupDescr object.ro DisplayString .1.3.6.1.4.1.207.8.1.1.10.1.3 |
deviceObjectIDTurboStack product family only.
The sysObject identification of the device.
For devices that are repeaters, this value is identical to
the rptrGroupObjectID object.ro OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.1.1.10.1.4 |
deviceIpAddrTurboStack product family only.
The IP address (if present) of the device.
For hubs devices, this object will return the same
value as hubIPAddr.ro IpAddress .1.3.6.1.4.1.207.8.1.1.10.1.5 |
devicePortCapacityTurboStack product family only.
The number of ports contained within the device.
Valid range is 1-1024. Within each device, the
ports are uniquely numbered in the range from
1 to devicePortCapacity.
For devices that are repeaters, this value is identical to
the rptrGroupPortCapacity object.ro INTEGER .1.3.6.1.4.1.207.8.1.1.10.1.6 |
localOmegaStateThis object enables the Local Omega to be enabled or disabled.rw Enumeration .1.3.6.1.4.1.207.8.1.1.11 |
remoteOmegaStateThis object enables the Remote Omega to be enabled or disabled.rw Enumeration .1.3.6.1.4.1.207.8.1.1.12 |
groupInfo OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.1.2 |
ledInfoSee groupLEDInforodeprecated OCTET STRING .1.3.6.1.4.1.207.8.1.2.1 |
groupInfoTableTable of group specific information. SEQUENCE OF GroupInfoEntry .1.3.6.1.4.1.207.8.1.2.2 |
groupInfoEntryAn entry in the table, containing information
about a single group of ports. GroupInfoEntry .1.3.6.1.4.1.207.8.1.2.2.1 |
groupInfoIndexThis object identifies the group within the
repeater for which this entry contains information.ro INTEGER .1.3.6.1.4.1.207.8.1.2.2.1.1 |
groupLEDInfoThis information encodes the current state of the module
per-port LEDs.ro OCTET STRING .1.3.6.1.4.1.207.8.1.2.2.1.2 |
groupSegmentationAT-3100 product family only.
This object controls the segmentation option for this group.
It may be segmented, connected, or using the module's
external segmentation switch.rw Enumeration .1.3.6.1.4.1.207.8.1.2.2.1.3 |
groupSecurityAT-3100 product family only.
This object controls the Security option for this group.
It may be enabled, disabled, or using module's external
security switch.rw Enumeration .1.3.6.1.4.1.207.8.1.2.2.1.4 |
groupIntruderProtectionAT-3100 and TurboStack product families only.
This object controls the Intruder Protection option for this
group/module. For TurboStack products, disabled turns off
Intruder Protection and places the module into source address
Learning Mode. Enabled turns on Intruder Protection and places
the module into Secure Mode.rw Enumeration .1.3.6.1.4.1.207.8.1.2.2.1.5 |
groupSrcAddrLearningModeAT-3100 product family only.
This object indicates the Source Address Learning Mode.
Mode1 : Automatic; passive devices: Automatic MAC address
learning. Re-learn port MAC address after a port is
disabled/re-enabled. Passive devices connected to a
port will see all backbone traffic.
Mode2 : Automatic; passive devices: Automatic MAC address
learning. Re-learn port MAC address after link test
fails (cable removed). Passive devices connected to a
port will see all backbone traffic.
Mode3 : Manual: No automatic MAC address learning (disabled).
Mode4 : Automatic; active devices: Automatic MAC address
learning. Re-learn port MAC address after a port is
disabled/re-enabled. Passive devices connected to a
port will see no backbone traffic.rw Enumeration .1.3.6.1.4.1.207.8.1.2.2.1.6 |
groupIntruderTrapAT-3100 and TurboStack product families only.
This object controls the action to be taken by this group/module
when an Intruder Alert event occurs. When this option is
enabled, the detection of an intruder (a received packet with
an unlearned or undefined source address) causes a Trap to be
sent to the configured host manager. When this option is
disabled then no Trap is sent on an Intruder Alert event.rw Enumeration .1.3.6.1.4.1.207.8.1.2.2.1.7 |
groupIntruderDisableAT-3100 and TurboStack product families only.
This object controls the action to be taken by this group/module
when an Intruder Alert event occurs. When this option is
enabled, the detection of an intruder (a received packet with
an unlearned or undefined source address) causes the port where
the intruder was detected to be automatically disabled. When
this option is disabled then the port will not be disabled on
an Intruder Alert event.rw Enumeration .1.3.6.1.4.1.207.8.1.2.2.1.8 |
groupOperStatusTurboStack product family only.
An object that indicates the operational status of the module.
For modules that are repeaters, this value is identical to
the rptrGroupOperStatus object.
A status of operational(2) indicates that the
module is present and functional within the chassis.
A status of malfunctioning(3) indicates that the
module is present within the chassis but is not functional.
A status of notPresent(4) indicates that the module is
temporarily or permanently physically and/or logically
not a part of the chassis.ro Enumeration .1.3.6.1.4.1.207.8.1.2.2.1.9 |
groupDescrTurboStack product family only.
A textual description of the module.
For modules that are repeaters, this value is identical to
the rptrGroupDescr object.ro DisplayString .1.3.6.1.4.1.207.8.1.2.2.1.10 |
groupObjectIDTurboStack product family only.
The sysObject identification of the module.
For modules that are repeaters, this value is identical to
the rptrGroupObjectID object.rodeprecated OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.1.2.2.1.11 |
groupIPAddressTurboStack product family only.
The IP address (if any) of the module.
For modules that are repeaters, this value is identical to
the actualIPAddr object. For non-repeater modules, this
object identifies the IP address that may be used to
communicate directly with the module.rodeprecated IpAddress .1.3.6.1.4.1.207.8.1.2.2.1.12 |
groupPortCapacityTurboStack product family only.
The number of ports contained within the module. Valid range
range is 1-1024. Within each module, the ports are uniquely
numbered in the range from 1 to groupPortCapacity.
For modules that are repeaters, this value is identical to
the rptrGroupPortCapacity object.rodeprecated INTEGER .1.3.6.1.4.1.207.8.1.2.2.1.13 |
groupEraseSourceAddressTableTurboStack product family only.
This object, when Set to the erase value, will clear (empty)
the module Source Address Table, deleting all learned MAC
addresses; this object will then automatically revert back to
the noerase state. When Set to noerase, no action is taken and
the Source Address Table remains unmodified. A Get of this
object will always return the noerase value.rw Enumeration .1.3.6.1.4.1.207.8.1.2.2.1.14 |
groupAddSourceAddressTurboStack product family only.
This object, when Set with a 48-bit MAC address value, will
add the new MAC address to the module Source Address Table.
A Get of this object will return a string of length zero.rw OCTET STRING .1.3.6.1.4.1.207.8.1.2.2.1.15 |
groupDeleteSourceAddressTurboStack product family only.
This object, when Set with a 48-bit MAC address value, will
delete the MAC address from the module Source Address Table.
A Get of this object will return a string of length zero.rw OCTET STRING .1.3.6.1.4.1.207.8.1.2.2.1.16 |
groupLimitAddressPerPortTurboStack product family only.
This object configures the module to allow no limitation
on number of source addresses on its ports, or limit to
only 1 source address per port.rw Enumeration .1.3.6.1.4.1.207.8.1.2.2.1.17 |
groupCheckPrimaryTimerTurboStack product family only.
The Check Primary Timer is the timer value in seconds
which determines how long to wait before checking if
the primary port could receive again. This timer applies
when the secondary port is enabled, and the primary port's
failure is NOT due to loss of link.
Range: 1 - 65535 in seconds, 0 means don't check receives.
Default is 60 seconds.rw INTEGER .1.3.6.1.4.1.207.8.1.2.2.1.18 |
groupReceiveFailureTimerTurboStack product family only.
The Receive Failure Timer is the timer value in seconds
which determines how long to wait before the secondary port
takes over when the primary port is not receiving data.
This timer applies only when the primary port's failure
is NOT due to loss of link.
Range: 0 - 65535 in seconds, 0 means don't check receives.
Default is 60 seconds.rw INTEGER .1.3.6.1.4.1.207.8.1.2.2.1.19 |
groupCheckResampleTimerTurboStack product family only.
The Resample Timer is the timer value in milliseconds
which determines how long to sample/test if the primary
port could receive data or is no longer partitioned.
This timer begins once groupCheckPrimaryTimer has expired,
and during this sampling time, the secondary port cannot
repeat data.
Range: 100 - 65535 milliseconds. Default is 200 milliseconds.rw INTEGER .1.3.6.1.4.1.207.8.1.2.2.1.20 |
portInfo OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.1.3 |
atiPortTableTable of descriptive and status information about
the ports. SEQUENCE OF AtiPortEntry .1.3.6.1.4.1.207.8.1.3.1 |
atiPortEntryAn entry in the table, containing information
about a single port. AtiPortEntry .1.3.6.1.4.1.207.8.1.3.1.1 |
atiPortGroupIndexThis object identifies the group containing the
port for which this entry contains information.ro INTEGER .1.3.6.1.4.1.207.8.1.3.1.1.1 |
atiPortIndexThis object identifies the port within the group
for which this entry contains information.
This value can never be greater than
rptrGroupPortCapacity for the associated group.ro INTEGER .1.3.6.1.4.1.207.8.1.3.1.1.2 |
portNamePort Namerw DisplayString .1.3.6.1.4.1.207.8.1.3.1.1.3 |
portStatePort State option: enabled allow repeating of packets
through the port; disabled turns off the port and prevents
packets repeating through the port.rw Enumeration .1.3.6.1.4.1.207.8.1.3.1.1.4 |
linkTestLink Test option: enabled turns on checking for link test
signals for the port; disabled turns off checking for
link test signals.rw Enumeration .1.3.6.1.4.1.207.8.1.3.1.1.5 |
altReconnectionReconnection Method: 1=IEEE Standard, 2=Alternate.rw Enumeration .1.3.6.1.4.1.207.8.1.3.1.1.6 |
polarityCorrectionPolarity Correction option: enabled turns on automatic
polarity correction for the port; disabled turns off automatic
polarity correction.rw Enumeration .1.3.6.1.4.1.207.8.1.3.1.1.7 |
partitionedLEDThis object reflects the current actual partitioning state of
the port. The notpartitioned value means that the port is
operational and repeating through the port is enabled.
The partitioned value means that the port is not operational
and repeating through the port is disabled.ro Enumeration .1.3.6.1.4.1.207.8.1.3.1.1.8 |
linkTestLEDThis object reflects the current actual link test state of
the port. The nolinktesterror value means that valid
link integrity test signals have been detected on the port,
indicating that an operable device is cabled to the port.
The linktesterror value means that no link integrity test
signals have been detected, indicating removal or failure
of the port-to-device cable, or that the device is not
operational. This object applies only to UTP (twisted pair)
and fiber optic ports (not AUI or BNC ports).ro Enumeration .1.3.6.1.4.1.207.8.1.3.1.1.9 |
polarityLEDThis object reflects the current actual polarity state of
the port. The notreversed value means that the port-to-device
cable connection is properly polarized. The reversed value
means that the cable connection has reversed polarity.
This object applies only to UTP (twisted pair) and
fiber optic ports (not AUI or BNC ports).ro Enumeration .1.3.6.1.4.1.207.8.1.3.1.1.10 |
portMACAddressAT-3100 product family only.
This object is either the MAC address of the
last readable frame (i.e., counted by
rptrMonitorPortReadableFrames) received by this
port, or a manually input MAC address. If neither
of those exists, then a string of length zero is
returned. If a 'read' operation is performed on
this object, the value it returns is the same as
the value returned by object
'rptrAddrTrackNewLastSrcAddress' in the Standard
Repeater MIB (RFC1516).rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.207.8.1.3.1.1.11 |
portFrames-64-127bytesTurboStack product family only.
The number of readable frames received on this port where
the frame length was in the range 64 through 127 octets.ro Counter .1.3.6.1.4.1.207.8.1.3.1.1.12 |
portFrames-128-255bytesTurboStack product family only.
The number of readable frames received on this port where
the frame length was in the range 128 through 255 octets.ro Counter .1.3.6.1.4.1.207.8.1.3.1.1.13 |
portFrames-256-511bytesTurboStack product family only.
The number of readable frames received on this port where
the frame length was in the range 256 through 511 octets.ro Counter .1.3.6.1.4.1.207.8.1.3.1.1.14 |
portFrames-512-1023bytesTurboStack product family only.
The number of readable frames received on this port where
the frame length was in the range 512 through 1023 octets.ro Counter .1.3.6.1.4.1.207.8.1.3.1.1.15 |
portFrames-1024-1518bytesTurboStack product family only.
The number of readable frames received on this port where
the frame length was in the range 1024 through 1518 octets.ro Counter .1.3.6.1.4.1.207.8.1.3.1.1.16 |
portRedundantPortTurboStack product family only.
This is the redundant port for atiPortIndex.
If the port is a secondary port as indicated in
portRedundantPosition, then it serves as a backup port.
This would indicate paired ports with redundant link.rw INTEGER .1.3.6.1.4.1.207.8.1.3.1.1.17 |
portRedundantPositionTurboStack product family only.
This object will retrieve the redundant position of the
port, primary or secondary port, if the port has a
redundant link to it.ro Enumeration .1.3.6.1.4.1.207.8.1.3.1.1.18 |
portLearningStateTurboStack product family only.
This object enable the learning on a port to be shut ON or OFF.
Once the learning is Shut Off, the learning of MAC Address
will stop.rw Enumeration .1.3.6.1.4.1.207.8.1.3.1.1.19 |
rptrStat OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.1.4 |
hubReadableFramesThe sum total of the Readable Frames Counters
of all ports on all modules/groupsro Counter .1.3.6.1.4.1.207.8.1.4.1 |
hubReadableOctetsThe sum total of the Readable Octets (bytes) Counters
of all ports on all modules/groupsro Counter .1.3.6.1.4.1.207.8.1.4.2 |
hubFCSErrorThe sum total of the FCS (CRC) Error Counters of all
ports on all modules/groupsro Counter .1.3.6.1.4.1.207.8.1.4.3 |
hubAlignErrorThe sum total of the Alignment Error Counters of all
ports on all modules/groupsro Counter .1.3.6.1.4.1.207.8.1.4.4 |
hubFrameTooLongThe sum total of the Frame Too Long Error Counters of all
ports on all modules/groupsro Counter .1.3.6.1.4.1.207.8.1.4.5 |
hubShortEventThe sum total of the Short Event Error Counters of all
ports on all modules/groupsro Counter .1.3.6.1.4.1.207.8.1.4.6 |
hubRuntThe sum total of the Runt Error Counters of all
ports on all modules/groupsro Counter .1.3.6.1.4.1.207.8.1.4.7 |
hubLateEventThe sum total of the Late Event Error Counters of all
ports on all modules/groupsro Counter .1.3.6.1.4.1.207.8.1.4.8 |
hubVeryLongEventThe sum total of the Very Long Event Error (Jabber)
Counters of all ports on all modules/groupsro Counter .1.3.6.1.4.1.207.8.1.4.9 |
hubDataRateMismThe sum total of the Data Rate Mismatch Error Counters
of all ports on all modules/groupsro Counter .1.3.6.1.4.1.207.8.1.4.10 |
hubAutoPartitionThe sum total of the Auto Port Partition Counters
of all ports on all modules/groupsro Counter .1.3.6.1.4.1.207.8.1.4.11 |
hubTotalErrorThe sum total of all Error Counters
of all ports on all modules/groupsro Counter .1.3.6.1.4.1.207.8.1.4.12 |
hubPortCollisionThe sum total of the Port Collision Counters
of all ports on all modules/groupsro Counter .1.3.6.1.4.1.207.8.1.4.13 |
hubFrames-64-127bytesTurboStack product family only.
The sum total number of readable frames received
on all ports on all modules/groups, where
the frame length was in the range 64 through 127 octets.ro Counter .1.3.6.1.4.1.207.8.1.4.14 |
hubFrames-128-255bytesTurboStack product family only.
The sum total number of readable frames received
on all ports on all modules/groups, where
the frame length was in the range 128 through 255 octets.ro Counter .1.3.6.1.4.1.207.8.1.4.15 |
hubFrames-256-511bytesTurboStack product family only.
The sum total number of readable frames received
on all ports on all modules/groups, where
the frame length was in the range 256 through 511 octets.ro Counter .1.3.6.1.4.1.207.8.1.4.16 |
hubFrames-512-1023bytesTurboStack product family only.
The sum total number of readable frames received
on all ports on all modules/groups, where
the frame length was in the range 512 through 1023 octets.ro Counter .1.3.6.1.4.1.207.8.1.4.17 |
hubFrames-1024-1518bytesTurboStack product family only.
The sum total number of readable frames received
on all ports on all modules/groups, where
the frame length was in the range 1024 through 1518 octets.ro Counter .1.3.6.1.4.1.207.8.1.4.18 |
groupStat OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.1.5 |
groupStatTableTable of performance and error statistics for the groups. SEQUENCE OF GroupStatEntry .1.3.6.1.4.1.207.8.1.5.1 |
groupStatEntryAn entry in the table, containing total
performance and error statistics for a single
group. Regular retrieval of the information in
this table provides a means of tracking the
performance and health of the networked devices
attached to this group's ports.
The counters in this table are redundant in the
sense that they are the summations of information
already available through other objects. However,
these sums provide a considerable optimization of
network management traffic over the otherwise
necessary retrieval of the individual counters
included in each sum. GroupStatEntry .1.3.6.1.4.1.207.8.1.5.1.1 |
groupStatIndexThis object identifies the group within the
repeater for which this entry contains information.ro INTEGER .1.3.6.1.4.1.207.8.1.5.1.1.1 |
groupFCSErrorThe sum total of the FCS (CRC) Error Counters of all
ports on this module/groupro Counter .1.3.6.1.4.1.207.8.1.5.1.1.2 |
groupAlignErrorThe sum total of the Alignment Error Counters of all
ports on this module/groupro Counter .1.3.6.1.4.1.207.8.1.5.1.1.3 |
groupFrameTooLongThe sum total of the Frame Too Long Error Counters of all
ports on this module/groupro Counter .1.3.6.1.4.1.207.8.1.5.1.1.4 |
groupShortEventThe sum total of the Short Event Error Counters of all
ports on this module/groupro Counter .1.3.6.1.4.1.207.8.1.5.1.1.5 |
groupRuntThe sum total of the Runt Error Counters of all
ports on this module/groupro Counter .1.3.6.1.4.1.207.8.1.5.1.1.6 |
groupPortCollisionThe sum total of the Port Collision Counters
of all ports on this module/groupro Counter .1.3.6.1.4.1.207.8.1.5.1.1.7 |
groupLateEventThe sum total of the Late Event Error Counters of all
ports on this module/groupro Counter .1.3.6.1.4.1.207.8.1.5.1.1.8 |
groupVeryLongEventThe sum total of the Very Long Event Error (Jabber)
Counters of all ports on this module/groupro Counter .1.3.6.1.4.1.207.8.1.5.1.1.9 |
groupDataRateMismThe sum total of the Data Rate Mismatch Error Counters
of all ports on this module/groupro Counter .1.3.6.1.4.1.207.8.1.5.1.1.10 |
groupAutoPartitionThe sum total of the Auto Port Partition Counters
of all ports on this module/groupro Counter .1.3.6.1.4.1.207.8.1.5.1.1.11 |
groupFrames-64-127bytesTurboStack product family only.
The sum total number of readable frames received
on all ports on this module/group, where
the frame length was in the range 64 through 127 octets.ro Counter .1.3.6.1.4.1.207.8.1.5.1.1.12 |
groupFrames-128-255bytesTurboStack product family only.
The sum total number of readable frames received
on all ports on this module/group, where
the frame length was in the range 128 through 255 octets.ro Counter .1.3.6.1.4.1.207.8.1.5.1.1.13 |
groupFrames-256-511bytesTurboStack product family only.
The sum total number of readable frames received
on all ports on this module/group, where
the frame length was in the range 256 through 511 octets.ro Counter .1.3.6.1.4.1.207.8.1.5.1.1.14 |
groupFrames-512-1023bytesTurboStack product family only.
The sum total number of readable frames received
on all ports on this module/group, where
the frame length was in the range 512 through 1023 octets.ro Counter .1.3.6.1.4.1.207.8.1.5.1.1.15 |
groupFrames-1024-1518bytesTurboStack product family only.
The sum total number of readable frames received
on all ports on this module/group, where
the frame length was in the range 1024 through 1518 octets.ro Counter .1.3.6.1.4.1.207.8.1.5.1.1.16 |
groupSAT OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.1.6 |
groupSourceAddressTableTurboStack product family only.
Table of learned and/or configured source MAC addresses which
defines the only valid and allowable source addresses for
this module (if Intruder Protection is enabled). SEQUENCE OF GroupSATEntry .1.3.6.1.4.1.207.8.1.6.1 |
groupSATEntryTurboStack product family only.
An entry in the Source Address Table, containing information
about a single source MAC address. GroupSATEntry .1.3.6.1.4.1.207.8.1.6.1.1 |
groupSATModuleTurboStack product family only.
This object identifies the group within the
repeater for which this entry contains information.ro INTEGER .1.3.6.1.4.1.207.8.1.6.1.1.1 |
groupSATIndexTurboStack product family only.
This object identifies the index within the Source Address
Table for which this entry contains information.ro INTEGER .1.3.6.1.4.1.207.8.1.6.1.1.2 |
groupSATMacAddressTurboStack product family only.
This object is the learned or configured source MAC address.
If no MAC address has been learned for this table entry (if
this is beyond the logical end of the table) then a string
of zero length will be returned.ro OCTET STRING .1.3.6.1.4.1.207.8.1.6.1.1.3 |
groupSATPortTurboStack product family only.
This object is the port number where the source MAC address
was last detected. If the MAC address has not been detected
since the system was last started, then this object will
be zero.ro INTEGER .1.3.6.1.4.1.207.8.1.6.1.1.4 |
atiTrapAttrs OBJECT IDENTIFIER .1.3.6.1.4.1.207.9 |
atiTrapIntruderMacAddressThe Mac address of the Intruder which is different from the rfc1516
object rptrAddrTrackLastSourceAddress is seen on port which is the
the next object OCTET STRING .1.3.6.1.4.1.207.9.1 |
atiTrapIntruderModuleNumberThis is the module number on which an intruder was seen. INTEGER .1.3.6.1.4.1.207.9.2 |
atiTrapIntruderPortNumberThis is the port number on which an intruder was seen. INTEGER .1.3.6.1.4.1.207.9.3 |
atiPortChangeDirectionThis is the direction of redundant port change. These two
values are used in the trap atiRedundantPortChangeTrap. Enumeration .1.3.6.1.4.1.207.9.4 |