AT-DS3-MIB
The AT-DS3-MIB module enables SNMP-based monitoring and management of AT&T DS3 (T3) interface hardware, specifically tracking physical layer statistics such as line status, error counts (SEFS, UAS), and signal quality metrics. This module facilitates the detection of transmission impairments and link failures on DS3 circuits by exposing standardized counter and status objects for the interface.
Imported Objects
Objects
9 total| Object Name |
|---|
ds3This MIB file contains definitions of managed objects for the DS3 module. MODULE-IDENTITY .1.3.6.1.4.1.207.8.4.4.4.109 |
ds3Traps OBJECT IDENTIFIER .1.3.6.1.4.1.207.8.4.4.4.109.0 |
tcaTrapA DS3 trap is generated when a threshold crossing alert occurs. This happens when an error count exceeds a pre determined value. The values are counted over 15 minute and 24 hour periods. Once a trap has occured in a given period it may not occur again within the same period. NOTIFICATION-TYPE .1.3.6.1.4.1.207.8.4.4.4.109.0.1 |
ds3TrapTableThe ATR enterprise DS3 trap table. SEQUENCE OF Ds3TrapEntry .1.3.6.1.4.1.207.8.4.4.4.109.1 |
ds3TrapEntryAn entry in the ATR enterprise DS3 trap table. Ds3TrapEntry .1.3.6.1.4.1.207.8.4.4.4.109.1.1 |
ds3TcaTrapEnableIndicates whether the threshold crossing alert traps should be generated for this interface.rw Enumeration .1.3.6.1.4.1.207.8.4.4.4.109.1.1.1 |
ds3TrapErrorThis variable shows which kind of parameter or primitive caused the trap. This variable is really just a placeholder for the object sent in the DS3 TRAP, but can be read independently if required. The variable will hold the value at the latest trap. A value of ds3NoError shows no trap has occuredro Enumeration .1.3.6.1.4.1.207.8.4.4.4.109.1.1.2 |
ds3TrapLocThis variable shows whether the trap was caused by a problem at the local or remote end. This variable is really just a placeholder for the object sent in the DS3 TRAP, but can be read independently if required. The variable will hold the value at the latest trap. A value of ds3NoLoc shows no trap had occured.ro Enumeration .1.3.6.1.4.1.207.8.4.4.4.109.1.1.3 |
ds3TrapIntervalThis variable shows whether the counter which has crossed the threshold is a twenty four hour or fifteen minute counter. This variable is really just a placeholder for the object sent in the DS3 TRAP, but can be read independently if required. The variable will hold the value at the latest trap. A value of ds3NoInt shows no trap has occured.ro Enumeration .1.3.6.1.4.1.207.8.4.4.4.109.1.1.4 |
More MIBs from Allied Telesis
Browse all Allied TelesisMIBs →The AT-UWC-WLAN-SWITCH-MIB provides vendor-specific SNMP management for Allied Telesis Universal Wireless Controller (UWC) hardware, enabling monitoring of WLAN switch operational states, interface statistics, and wireless client association metrics.
The AtiEdgeSwitch-MIB provides vendor-specific SNMP extensions for monitoring and managing Layer 2 stackable switch operations, including interface status, port statistics, and stack topology, on ATI hardware platforms within Windows and UNIX network management environments.
Standard SNMP MIB module defining data structures for ALLIEDTELESYN-MIB.
The AT-BOARDS-MIB module provides a structured OID hierarchy for monitoring and managing specific hardware components on Allied Telesis devices, including board identifiers, firmware release versions, interface type definitions, and integrated chip IDs. This MIB enables granular inventory tracking and hardware status verification by mapping logical identifiers to physical subsystems within the network equipment chassis.
SWITCH-ATM-MIB monitors and manages Asynchronous Transfer Mode (ATM) interfaces and virtual circuit states on network switches, specifically tracking VPI/VCI pairings and traffic counters under the constraint that the Virtual Path Identifier is fixed by the implementation and excluded from table indexing.
Standard SNMP MIB module defining data structures for AtiL2-MIB.