ASKEY-SYSTEM-MIB
AI MIB Summary
The ASKEY-SYSTEM-MIB provides SNMP management interfaces for ASKEY ADSL modems and routers, enabling the monitoring of DSL line parameters such as attenuation, signal-to-noise ratio, and interface status. It facilitates the collection of ADSL-specific performance counters and error statistics required for troubleshooting broadband connectivity issues on vendor hardware.
ASKEY ADSL MIB OID defines and documentation.
Main OID:
askeySystemMib.1.3.6.1.4.1.3646.1300.2.1
139
Objects
Active
Status
9
Dependencies
Imported Objects
Objects
139 total| Object Name |
|---|
askeySystemMibASKEY ADSL MIB OID defines and documentation. MODULE-IDENTITY .1.3.6.1.4.1.3646.1300.2.1 |
ipConfig OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.1 |
nodeIP OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.1.1 |
nodeIPAddrThe IP address of node. It applies to the trunk (up-link) port.rw IpAddress .1.3.6.1.4.1.3646.1300.2.1.1.1.1 |
nodeIPNetMaskThe subnet mask associated with the IP address of this node. The
value of the mask is an IP address with all the network bits set
to 1 and all the hosts bits set to 0.rw IpAddress .1.3.6.1.4.1.3646.1300.2.1.1.1.2 |
nodeMACAddrThe MAC address of the trunk (up-link) port.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.3646.1300.2.1.1.1.3 |
gatewayIPAddrThe gateway IP address of node. It applies to the trunk
(up-link) port.rw IpAddress .1.3.6.1.4.1.3646.1300.2.1.1.1.4 |
mgmtIP OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.1.2 |
mgmtIPAddrThe IP address of the management (out-band) port.rw IpAddress .1.3.6.1.4.1.3646.1300.2.1.1.2.1 |
mgmtIPNetMaskThe subnet mask associated with the IP address of the management
port. The value of the mask is an IP address with all the network
bits set to 1 and all the hosts bits set to 0.rw IpAddress .1.3.6.1.4.1.3646.1300.2.1.1.2.2 |
mgmtMACAddrThe MAC address of the manaement (out-band) port.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.3646.1300.2.1.1.2.3 |
nodeTime OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.2 |
timeThe time <yyyy-mm-dd hh:mm:ss> of the system.rw DisplayString .1.3.6.1.4.1.3646.1300.2.1.2.1 |
zoneThe time zone of the system.rw INTEGER (-12..13) .1.3.6.1.4.1.3646.1300.2.1.2.2 |
snmpTrapMib OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.6 |
snmpTrapTableThis table contains information for SNMP Trap. SEQUENCE OF SnmpTrapEntry .1.3.6.1.4.1.3646.1300.2.1.6.1 |
snmpTrapEntryAn entry of parameters in snmpTrap table. SnmpTrapEntry .1.3.6.1.4.1.3646.1300.2.1.6.1.1 |
snmpTrapStationThe IP address of the workstation which the SNMP Trap is sent to. IpAddress .1.3.6.1.4.1.3646.1300.2.1.6.1.1.1 |
snmpTrapCommunityDURABLE: { 'public','':all }
The SNMPv1/v2c community name string. Duplicate community names
are not allowed in this table. Note that a null string is not a
valid community name. Attempting to set this object to a null
string or to a duplicate value results in the agent returning a
'badValue' error for SNMPv1 or 'inconsistentValue' error for
SNMPv2c/v3.rw DisplayString .1.3.6.1.4.1.3646.1300.2.1.6.1.1.2 |
snmpTrapSNMPVersionThis object indicates the version of SNMPv1 or SNMPv2c.ro Enumeration .1.3.6.1.4.1.3646.1300.2.1.6.1.1.3 |
snmpTrapRowStatusThis object indicates the status of SNMP trap.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3646.1300.2.1.6.1.1.4 |
snmpCommunityMib OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.7 |
snmpCommunityTableA table of SNMPv1/v2c community string to SNMPv3 view name
mappings. SEQUENCE OF SnmpCommunityEntry .1.3.6.1.4.1.3646.1300.2.1.7.1 |
snmpCommunityEntryAn entry containing objects about SNMP community at this systemp. SnmpCommunityEntry .1.3.6.1.4.1.3646.1300.2.1.7.1.1 |
snmpCommunityNameThe SNMPv1/v2c community name string. Duplicate community names
are not allowed in this table. Note that a null string is not a
valid community name. Attempting to set this object to a null
string or to a duplicate value results in the agent returning a
'badValue' error for SNMPv1 or 'inconsistentValue' error for
SNMPv2c/v3. DisplayString .1.3.6.1.4.1.3646.1300.2.1.7.1.1.1 |
snmpCommunityPermissionThis object specifies the type of access allowed. 'readOnly(1)'
allows GET operations (i.e., GET, GET-NEXT, GET-BULK) and
'readWrite(2)' allows both GET and SET operations.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.7.1.1.2 |
snmpCommunityRowStatusThis object indicates the status of this entry. A row in this
table can be created using the 'createAndGo(4)' (if all objects
without default values are supplied with valid values in a single
SNMP PDU) or the 'createAndWait(5)' action states. Until all
parameters are valid for a conceptual row, this object is
'notReady(3)'. All parameters must be valid before this object
can be set to 'active(1)'.
Any object in a conceptual row can be modified independent of the
value of this object (that is, can be changed while 'active(1)',
notInService(2) or 'notReady(3)').rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3646.1300.2.1.7.1.1.3 |
askeyDslamFdbTableA table that contains information about unicast entries for which
the IP-DSLAM has forwarding and/or filtering information. This
information is used by the transparent bridging function in
determining how to propagate a received frame. SEQUENCE OF AskeyDslamFdbEntry .1.3.6.1.4.1.3646.1300.2.1.9 |
askeyDslamFdbEntryInformation about a specific unicast MAC address on a specific
line for which the IP-DSLAM has some forwarding and/or filtering
information. AskeyDslamFdbEntry .1.3.6.1.4.1.3646.1300.2.1.9.1 |
fdbMacIndexA simple index into 'askeyDslamFdbTable'.ro INTEGER .1.3.6.1.4.1.3646.1300.2.1.9.1.1 |
fdbVpiThe VPI value of the VCL. The maximum VPI value cannot exceed the
value allowable by the atmInterfaceMaxVpiBits.ro INTEGER .1.3.6.1.4.1.3646.1300.2.1.9.1.2 |
fdbVciThe VCI value of the VCL. The maximum VCI value cannot exceed the
value allowable by the atmInterfaceMaxVciBits.ro INTEGER .1.3.6.1.4.1.3646.1300.2.1.9.1.3 |
macAddressA unicast MAC address for which the bridge has forwarding and/or
filtering information.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.3646.1300.2.1.9.1.4 |
askeyDslamFdbStatusThe status of this entry. The meanings of the values are:
learned_unique(1): the value of the corresponding instance of
macAddress was learned, and is being used.
It indicates that the macAddress is an unique
one and there is no duplicated (spoofed) one
detected in the IP-DSLAM.
learned_spoofed_active(2) : the value of the corresponding instance
of macAddress was learned, and is being used.
It indicates that there is an duplicated
(spoofed) one detected in theIP-DSLAM.
learned_spoofed_inactive(3) : the value of the corresponding
instance of macAddress was learned, and is NOT
being used. It indicates that there is an
duplicated(spoofed) one detected in the IP-DSLAM.
mgmt_forbid(4): the value of the corresponding instance of
macAddress was set by the operator. It
indicates that an Ethernet frame of
srcMac='macAddress' is to be dropped by the
IP-DSLAM.
mgmt_permit(5): the value of the corresponding instance of
macAddress was set by the operator. It
indicates that an Ethernet frame of
srcMac='macAddress' is to be forwarded by the
IP-DSLAM.
learned_routed(6): the value of the corresponding instance of
macAddress was learned, and is being used. It
indicates that the macAddress is added by the
IP-DSLAM.ro Enumeration .1.3.6.1.4.1.3646.1300.2.1.9.1.5 |
configDataMibsave(1): save the current configuration data to NVRAM(flash) as
the main configuration data.
restore(2): replace the main configuration data with the backup
configuration data.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.10 |
askeyCardInfoTableThis table is information about card/slot on ASKEY IPDSLAM. SEQUENCE OF AskeyCardInfoEntry .1.3.6.1.4.1.3646.1300.2.1.11 |
askeyCardInfoEntryAn entry about information of the card/slot. AskeyCardInfoEntry .1.3.6.1.4.1.3646.1300.2.1.11.1 |
askeyCardPlannedTypeSupposed type of this card.rw INTEGER .1.3.6.1.4.1.3646.1300.2.1.11.1.1 |
askeyCardTypeCurrent working type of this card.ro INTEGER .1.3.6.1.4.1.3646.1300.2.1.11.1.2 |
askeyCardHWVersionThe Hardware version of this card.ro DisplayString .1.3.6.1.4.1.3646.1300.2.1.11.1.3 |
askeyCardSWVersionThe Software version of this card.ro DisplayString .1.3.6.1.4.1.3646.1300.2.1.11.1.4 |
askeyCardImageDescription for the location of the image.ro DisplayString .1.3.6.1.4.1.3646.1300.2.1.11.1.5 |
askeyCardUptimeThe uptime (in seconds) of this card.ro INTEGER .1.3.6.1.4.1.3646.1300.2.1.11.1.6 |
askeyCardRoleThis object descibes the card role.ro Enumeration .1.3.6.1.4.1.3646.1300.2.1.11.1.7 |
askeyCardSerialNumberThe card serial number which is an unique number.ro DisplayString .1.3.6.1.4.1.3646.1300.2.1.11.1.8 |
askeyCardAdminStatusThe operation of this card. Only value is 'reset(1)' will reset
this card.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.11.1.9 |
askeyCardOperStatusThis object indicates the card's operational status. The
notPresent(3) status indicates the card is physically removed
(note this may or may not be possible depending on the type of
card.) The operational(1) status indicates that the card is
enabled (see rptrPortAdminStatus) and working, even though it might
be auto-partitioned (see rptrPortAutoPartitionState).
If this object has the value operational(1) and cwmAdminStatus is
set to disabled(2), it is expected that this object's value will
soon change to notOperational(2).ro Enumeration .1.3.6.1.4.1.3646.1300.2.1.11.1.10 |
lineCardAdminVlanTagPassEnabledEnable(1) or disable VLAN tag pass through function.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.11.1.11 |
lineCardOperVlanTagPassEnabledCurrent status of VLAN tag passes through funtion.ro Enumeration .1.3.6.1.4.1.3646.1300.2.1.11.1.12 |
lineCardAdminRfc2684EncapSetting this object to LLC (1) to encapsulate the packet to
LLC style. Setting it to vcMux (2) to encapsulate the packet to
VC-MUX style.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.11.1.13 |
lineCardOperRfc2684EncapCurrent applied rfc2684 encapsulation method.ro Enumeration .1.3.6.1.4.1.3646.1300.2.1.11.1.14 |
lineCardServiceTypeControlSet or get applied control of service type.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.11.1.15 |
shdslFirmwareUpgradeUpgrade SHDSL line card firmware.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.11.1.16 |
shdslFirmwareUpgradeStateSHDSL line card firmware pgrade state.ro Enumeration .1.3.6.1.4.1.3646.1300.2.1.11.1.17 |
taggedModeAdminStatusCard administrative tagged mode. This entry indicates tagged mode
configured on the specific card.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.11.1.18 |
taggedModeOperStatusCard operational tagged mode. This entry indicates tagged mode
running on the specific card. All ports of the tagged type card will
drop packets that don't have tagged header. And all ports of
untagged type card will drop packets that have tagged header.
Do nothing for 'noAction' case.ro Enumeration .1.3.6.1.4.1.3646.1300.2.1.11.1.19 |
linePortInfo OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.12 |
linePortInfoTableA list of line port information entries. SEQUENCE OF LinePortInfoEntry .1.3.6.1.4.1.3646.1300.2.1.12.1 |
linePortInfoEntryAn information entry containing objects for each line port. LinePortInfoEntry .1.3.6.1.4.1.3646.1300.2.1.12.1.1 |
linePortAdminStatusThe desired state of the line port. The enable(1) state ready
to pass packets. The disable(2) state stop passing any packets.
The testing(3) state indicates that no operational packets can be
passed, it is for debug only. Finally, reset(4) state will reset
this line port.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.12.1.1.1 |
linePortOperStatusThis object indicates the line port's operational status. The
notPresent(3) status indicates the line port is physically removed
(note this may or may not be possible depending on the type of
port). The operational(1) status indicates that the port is
enabled (see rptrPortAdminStatus) and working, even though it might
be auto-partitioned (see rptrPortAutoPartitionState). If this
object has the value operational(1) and rptrPortAdminStatus is set
to disabled(2), it is expected that this object's value will soon
change to notOperational(2).ro Enumeration .1.3.6.1.4.1.3646.1300.2.1.12.1.1.2 |
circuitIDThe identity for this circuit. The value is 'shelf.slot.port'.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.3646.1300.2.1.12.1.1.3 |
remoteIDThe string is sent transparently to authorization service.rw SnmpAdminString .1.3.6.1.4.1.3646.1300.2.1.12.1.1.4 |
dot1TpMACAgingThis object decides MAC enrties aged out or not.
aged: MAC entries will be aged out
nonaged: MAC entries will never be aged outrw Enumeration .1.3.6.1.4.1.3646.1300.2.1.13 |
askeyRebootSystemActionReboot the system.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.14 |
askeyDslamOam OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.15 |
oamF5 OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.15.1 |
oamF5IfIndexThe ifIndex of the line.rw INTEGER .1.3.6.1.4.1.3646.1300.2.1.15.1.1 |
oamF5VpiThe VPI value of the VCL. The maximum VPI value cannot exceed the
value allowable by the atmInterfaceMaxVpiBits.rw INTEGER .1.3.6.1.4.1.3646.1300.2.1.15.1.2 |
oamF5VciThe VCI value of the VCL. The maximum VCI value cannot exceed the
value allowable by the atmInterfaceMaxVciBits.rw INTEGER .1.3.6.1.4.1.3646.1300.2.1.15.1.3 |
oamF5ScopeThe scope of the OAM F5 loopback cell. Set this object will
trigger OAM processing.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.15.1.4 |
askeySystemManagementInfo OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.16 |
askeyEmsVlanIdIn-band management VLAN ID.rw INTEGER .1.3.6.1.4.1.3646.1300.2.1.16.1 |
askeyBootDevice OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.16.2 |
askeyNextBootDeviceConfigure the next boot partition.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.16.2.1 |
askeyCurrentBootDeviceShow current the boot partition.ro Enumeration .1.3.6.1.4.1.3646.1300.2.1.16.2.2 |
askeySystemManagementIgmpConfigure the IGMP proxy and IGMP snoop.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.16.3 |
askeyRedundancy OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.16.4 |
askeyRedundancyAutoSyncEnabledThe Askey IPDSLAM can auto synchronize standby NC configuration
with active NC. This object enables or disables such
synchronization.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.16.4.1 |
askeyRedundancyAutoSyncPeriodAuto synchronization period. The value unit is in second.rw INTEGER .1.3.6.1.4.1.3646.1300.2.1.16.4.2 |
askeyRedundancySyncSynchronize redundancy immediately.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.16.4.3 |
askeySystemManagementInfoVlan OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.16.5 |
askeySystemManagementInfoVlanMacLimitTableA table that contains information about the MAC limit per VLAN ID. SEQUENCE OF AskeySystemManagementInfoVlanMacLimitEntry .1.3.6.1.4.1.3646.1300.2.1.16.5.1 |
askeySystemManagementInfoVlanMacLimitEntryInformation about the MAC limit per VLAN. AskeySystemManagementInfoVlanMacLimitEntry .1.3.6.1.4.1.3646.1300.2.1.16.5.1.1 |
askeySystemManagementInfoVlanIDThe ID of target VLAN which MAC limits. INTEGER .1.3.6.1.4.1.3646.1300.2.1.16.5.1.1.1 |
askeySystemManagementInfoVlanMacLimitMAC limit on specific VLAN. Default values are 5376 for AM0021
and 1568 for AM0031.rw INTEGER .1.3.6.1.4.1.3646.1300.2.1.16.5.1.1.2 |
askeySystemManagementInfoVlanMacLimitEnabledEnable or disable MAC limit.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.16.5.1.1.3 |
askeyCosQueue OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.18 |
askeyCosQueueMappingTableA table that contains information about COS queues mapping with
802.1p. SEQUENCE OF AskeyCosQueueMappingEntry .1.3.6.1.4.1.3646.1300.2.1.18.1 |
askeyCosQueueMappingEntryInformation about COS queue mapping. AskeyCosQueueMappingEntry .1.3.6.1.4.1.3646.1300.2.1.18.1.1 |
askeyCosQueueMapping8021pThe identity of the specific 802.1p priority mapping.ro INTEGER .1.3.6.1.4.1.3646.1300.2.1.18.1.1.1 |
askeyCosQueueIndexThe index of COS queue.rw INTEGER .1.3.6.1.4.1.3646.1300.2.1.18.1.1.2 |
askeySystemUserAccountTableThis table contains information of system user account. One
entry in this table reflects a user information. SEQUENCE OF AskeySystemUserAccountEntry .1.3.6.1.4.1.3646.1300.2.1.19 |
askeySystemUserAccountEntryAn entry reflects a user information. AskeySystemUserAccountEntry .1.3.6.1.4.1.3646.1300.2.1.19.1 |
askeySystemUserAccountUserNameThe name of account user.rw SnmpAdminString .1.3.6.1.4.1.3646.1300.2.1.19.1.1 |
askeySystemUserAccountPasswordThe password of account user.rw SnmpAdminString .1.3.6.1.4.1.3646.1300.2.1.19.1.2 |
askeySystemUserAccountGroupThe group which account belongs to.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.19.1.3 |
askeySystemUserAccountRowStatusThis object controls creation/deletion of the associated
entry in this table as per the semantics of RowStatus.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3646.1300.2.1.19.1.4 |
askeyPPPoE OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.20 |
suboptionEnable or disable PPPoE suboption. The circuit information
recorded on 'linePortInfo' table will be transferred to
authorization service, for example, a radius server, if this
function enabled.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.20.1 |
dnsService OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.21 |
dnsServer1IPAddressThe IP address of DNS server. This server is used first priority.rw IpAddress .1.3.6.1.4.1.3646.1300.2.1.21.1 |
dnsServer2IPAddressThe IP address of DNS server. This server is used second
priority.rw IpAddress .1.3.6.1.4.1.3646.1300.2.1.21.2 |
dnsServer3IPAddressThe IP address of DNS server. This server is used lowest
priority.rw IpAddress .1.3.6.1.4.1.3646.1300.2.1.21.3 |
timeService OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.22 |
protocolThe time service is used which protocol.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.22.1 |
updatePeriodSynchronize time which system update time by time servers.
This object unit is in minute.rw Unsigned32 .1.3.6.1.4.1.3646.1300.2.1.22.2 |
timeServer1InetAddressThe address of time server1. This server is used first priority.rw InetAddress .1.3.6.1.4.1.3646.1300.2.1.22.3 |
timeServer2InetAddressThe address of time server2. This server is used second priority.rw InetAddress .1.3.6.1.4.1.3646.1300.2.1.22.4 |
timeServer3InetAddressThe address of time server3. This server is used lowest priority.rw InetAddress .1.3.6.1.4.1.3646.1300.2.1.22.5 |
timeServer1Statusserver1 current status.ro Enumeration .1.3.6.1.4.1.3646.1300.2.1.22.6 |
timeServer2Statusserver2 current status.ro Enumeration .1.3.6.1.4.1.3646.1300.2.1.22.7 |
timeServer3Statusserver3 current status.ro Enumeration .1.3.6.1.4.1.3646.1300.2.1.22.8 |
timeZoneThe system time zone.rw INTEGER (-12..13) .1.3.6.1.4.1.3646.1300.2.1.22.9 |
ugeMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.23 |
ugeAutoNegotiationTableThe table indicates UGE auto negotiation states. SEQUENCE OF UgeAutoNegotionEntry .1.3.6.1.4.1.3646.1300.2.1.23.2 |
ugeAutoNegotionEntryAn entry indicates UGE auto negotiation states. UgeAutoNegotionEntry .1.3.6.1.4.1.3646.1300.2.1.23.2.1 |
autoNegotiationStateEnable or disable UGE port auto negotiation.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.23.2.1.1 |
ugePauseFrameStatisticTableThe table indicates UGE pause packet statistic. SEQUENCE OF UgePauseFrameStatisticEntry .1.3.6.1.4.1.3646.1300.2.1.23.3 |
ugePauseFrameStatisticEntryAn entry indicates UGE pause packet statistic. UgePauseFrameStatisticEntry .1.3.6.1.4.1.3646.1300.2.1.23.3.1 |
rxPausePacketsThe counter indicates pause packets received from this UGE.ro Unsigned32 .1.3.6.1.4.1.3646.1300.2.1.23.3.1.1 |
txPausePacketsThe counter indicates pause packets transmitted by this UGE.ro Unsigned32 .1.3.6.1.4.1.3646.1300.2.1.23.3.1.2 |
subtendVLANTableThe table indicates which VLAN packets can pass through subtending
ports. SEQUENCE OF SubtendVLANEntry .1.3.6.1.4.1.3646.1300.2.1.23.4 |
subtendVLANEntryAn entry for subtendVLANTable. SubtendVLANEntry .1.3.6.1.4.1.3646.1300.2.1.23.4.1 |
subtendStateEnable or disable NC VLAN subtend.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.23.4.1.1 |
subtendVLANSpecify what VLAN can pass through by subtending port.rw VLANList .1.3.6.1.4.1.3646.1300.2.1.23.4.1.2 |
ugeVLANTableThis table indicates relation between UGEs and packets with
specific VLAN tags. Only packets with tag values can been send out
from UGEs, otherwise will not. SEQUENCE OF UgeVLANEntry .1.3.6.1.4.1.3646.1300.2.1.23.5 |
ugeVLANEntryAn entry for ugeVLANTable. UgeVLANEntry .1.3.6.1.4.1.3646.1300.2.1.23.5.1 |
ugeVLANSpecify what VLAN can pass through by UGE port.ro VLANList .1.3.6.1.4.1.3646.1300.2.1.23.5.1.1 |
securedHosts OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.24 |
securedHostAdminStatusEnable or disable secured host function.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.24.1 |
securedHostTableThis table provides the information of the secured hosts which may
access managed system. SEQUENCE OF SecuredHostEntry .1.3.6.1.4.1.3646.1300.2.1.24.2 |
securedHostEntryAn entry to information of the secured hosts which may access
managed system. SecuredHostEntry .1.3.6.1.4.1.3646.1300.2.1.24.2.1 |
securedIPSectorIndexAn IP sector index. IPSectionIndex .1.3.6.1.4.1.3646.1300.2.1.24.2.1.1 |
securedIPSectorStartIPAn IP address expresses IP sector starting.rw IpAddress .1.3.6.1.4.1.3646.1300.2.1.24.2.1.2 |
securedIPSectorEndIPAn IP address expresses IP sector ending.rw IpAddress .1.3.6.1.4.1.3646.1300.2.1.24.2.1.3 |
allowedServiceTypeContains indicates whether access mode is enabled or disabled.
This is a bit-map of possible settings.rw Bits .1.3.6.1.4.1.3646.1300.2.1.24.2.1.4 |
netBIOSFilter OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.1.25 |
netBIOSFilterActionDrop or forward NetBIOS/NetBEUI packets.rw Enumeration .1.3.6.1.4.1.3646.1300.2.1.25.1 |