ASKEY-HARDWARE-INFORMATION-MIB
The ASKEY-HARDWARE-INFORMATION-MIB enables SNMP-based monitoring of ASKEY network equipment by exposing operational status and telemetry for network cards, line cards, and fan modules. This module facilitates hardware health assessment and fault detection through standardized access to component-level inventory and state data.
Imported Objects
Objects
29 total| Object Name |
|---|
askeyHwInfoThis Mib describs with the information of network card, line card and fan module. MODULE-IDENTITY .1.3.6.1.4.1.3646.1300.2.15 |
askeyHwInfoTableThis table describes the information and the limit of voltage and temperature about network card, line card and fan tray. SEQUENCE OF AskeyHwInfoEntry .1.3.6.1.4.1.3646.1300.2.15.1 |
askeyHwInfoEntry AskeyHwInfoEntry .1.3.6.1.4.1.3646.1300.2.15.1.1 |
askeyHwInfoTypeThis object describes the measure value about rotation speed of fan, voltage or temperature of the equipment include network card, line card, and fan tray. Enumeration .1.3.6.1.4.1.3646.1300.2.15.1.1.1 |
askeyHwSensorIdThis object describes the index that mapping to the sensor of the hardware device: on the network card, there is 1 max6652; on the line card, there are 2 max6652s with 8 sensor, and each chip has 4 sensors to measure the voltage. INTEGER .1.3.6.1.4.1.3646.1300.2.15.1.1.2 |
askeyHwSensorDescriptionThis object describes the sensor on the nc or lcro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3646.1300.2.15.1.1.3 |
askeyHwValueThis object describes the value of hardware on the nc or lcro INTEGER .1.3.6.1.4.1.3646.1300.2.15.1.1.4 |
askeyHwRefValueThis object describes the reference value of hardware on the nc or lcro INTEGER .1.3.6.1.4.1.3646.1300.2.15.1.1.5 |
askeyHwValueThreshholdLowThis object describes the low-bound value of the voltage on the nc or lc. If the measured value is lower than the value, the system will report the alarm.ro INTEGER .1.3.6.1.4.1.3646.1300.2.15.1.1.6 |
askeyHwValueThreshholdHighThis object describes the high-bound value of the voltage on the nc or lc. If the measured value is higher than the value, the system will report the alarm.ro INTEGER .1.3.6.1.4.1.3646.1300.2.15.1.1.7 |
sensorThresholds OBJECT IDENTIFIER .1.3.6.1.4.1.3646.1300.2.15.2 |
sensorTempHighThe threshold for temperature up bound. Its range is from -20 C to 100 Crw INTEGER (-20..100) .1.3.6.1.4.1.3646.1300.2.15.2.1 |
sensorTempLowThe threshold for temperature low bound. Its range is from -20 C to 100 Crw INTEGER (-20..100) .1.3.6.1.4.1.3646.1300.2.15.2.2 |
gbicModuleTableGBIC module information SEQUENCE OF GbicModuleTableEntry .1.3.6.1.4.1.3646.1300.2.15.3 |
gbicModuleTableEntry GbicModuleTableEntry .1.3.6.1.4.1.3646.1300.2.15.3.1 |
gbicIdentifierThis object describes the identifier value specifies the physical device described by the serial information. A value 3 means SFP.ro INTEGER .1.3.6.1.4.1.3646.1300.2.15.3.1.1 |
gbicConnectorThe connector value indicates the external connector provided on the interface. A value 1 means SC. A value 7 means LC.ro INTEGER .1.3.6.1.4.1.3646.1300.2.15.3.1.2 |
gbicTransceiverThis object describes the gigabit ethernet compliance codes.The following bit significant indicators define the electronic or optical interfaces that are supported by the GBIC. 6 - IEEE ethernet standard: bit 0 - 1000BASE-SX 1 - 1000BASE-LX 2 - 1000BASE-CX 3 - 1000BASE-Tn 7 - bit 0 - electrical inter-enclosure(EL) 1 - longwave laser(LC) distance capability: bit 4 - long distance(L) 5 - intermediate distance(I) 6 - short distance(S) 7 - very long distance(V) 8 - SONET compliance codes: bit 4 - longwave laser(LL) 5 - shortwave laser w/OFC(SL) 6 - shortwave laser w/o OFC(SN) 7 - intra-enclosure (EL) 9 - transmission media type: bit 0 - single mode(SM) 2 - multi-mode-50m(M5) 3 - multi-mode-62.5m(M6) 4 - video coax(TV) 5 - miniature coax(MI) 6 - shielded twisted pair(TP) 7 - twin axial pair(TW) 10 - fibre channel link length: bit 0 - 100MBytes/Sec 2 - 200MBytes/Sec 4 - 400MBytes/Secro Unsigned32 .1.3.6.1.4.1.3646.1300.2.15.3.1.3 |
gbicEncodingThe encoding value indicates the serial encoding mechanism that is the nominal design target of the particular GBIC. value 0 - Unspecified 1 - 8B10B 2 - 4B5B 3 - NRZ 4 - Manchester 5 - SONET Scrambledro INTEGER .1.3.6.1.4.1.3646.1300.2.15.3.1.4 |
gbicBrNominalThe nominal bit rate (BR, nominal) is specified in units of 100 Megabits per second, rounded off to the nearest 100 Megabits per second. The bit rate includes those bits necessary to encode and delimit the signal as well as those bits carrying data information. A value of 0 indicates that the bit rate is not specified and must be determined from the transceiver technology. The actual information transfer rate will depend on the encoding of the data, as defined by the encoding value.ro INTEGER .1.3.6.1.4.1.3646.1300.2.15.3.1.5 |
gbicLength9umThis value specifies the link length that is supported by the GBIC while operating in compliance with the applicable standards using single mode fiber.The value is in units of 100 meters. A value of 255 means that the GBIC supports a link length greater than 25.4 km. A value of zero means that the GBIC does not support single mode fiber or that the length information must be determined from the transceiver technology.ro INTEGER .1.3.6.1.4.1.3646.1300.2.15.3.1.6 |
gbicLength50umThis value specifies the link length that is supported by the GBIC while operating in compliance with the applicable standards using 50 micron multi-mode fiber. The value is in units of 10 meters. A value of 255 means that the GBIC supports a link length greater than 2.54 km. A value of zero means that the GBIC does not support 50 micron multi-mode fiber or that the length information must be determined from the transceiver technology.ro INTEGER .1.3.6.1.4.1.3646.1300.2.15.3.1.7 |
gbicLength62_5umThis value specifies the link length that is supported by the GBIC while operating in compliance with the applicable standards using 62.5 micron multi-mode fiber. The value is in units of 10 meters. A value of 255 means that the GBIC supports a link length greater than 2.54 km. A value of zero means that the GBIC does not 62.5 micron multi-mode fiber or that the length information must determined from the transceiver technology. It is common for GBICs to support both 50 micron and 62.5 micron fiber.ro INTEGER .1.3.6.1.4.1.3646.1300.2.15.3.1.8 |
gbicCopperLengthThis value specifies the minimum link length that is supported by the GBIC while operating in compliance with the applicable standards using copper cable. The value is in units of 1 meter. A value of 255 means that the GBIC supports a link length greater than 254 meters. A value of zero means that the GBIC does not support copper cables or that the length information must be determined from the transceiver technology. Further information about the cable design, equalization, and connectors is usually required to guarantee meeting a particular length requirement.ro INTEGER .1.3.6.1.4.1.3646.1300.2.15.3.1.9 |
gbicVendorNameThe vendor name is a 16 character field that contains ASCII characters, left-aligned and padded on the right with ASCII spaces (20h). The vendor name shall be the full name of the corporation, a commonly accepted abbreviation of the name of the corporation, the SCSI company code for the corporation, or the stock exchange code for the corporation. At least one of the vendor name or the vendor OUI fields shall contain valid serial data.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3646.1300.2.15.3.1.10 |
gbicVendorOUIThe vendor organizationally unique identifier field (vendor OUI) is a 3-byte field that contains the IEEE Company Identifier for the vendor. A value of all zero in the 3-byte field indicates that the Vendor OUI is unspecified.ro Unsigned32 .1.3.6.1.4.1.3646.1300.2.15.3.1.11 |
gbicVendorPNThe vendor part number (vendor PN) is a 16-byte field that contains ASCII characters, left-aligned and padded on the right with ASCII spaces (20h), defining the vendor part number or product name. A value of all zero in the 16-byte field indicates that the vendor PN is unspecified.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3646.1300.2.15.3.1.12 |
gbicVendorSNThe vendor serial number (vendor SN) is a 16 character field that contains ASCII characters, left-aligned and padded on the right with ASCII spaces (20h), defining the vendor's serial number for the GBIC. A value of all zero in the 16-byte field indicates that the vendor PN is unspecified.ro Unsigned32 .1.3.6.1.4.1.3646.1300.2.15.3.1.13 |
gbicLaserWaveLengthThis object describes the fibre channel transmitter wave laser length(nm).ro INTEGER .1.3.6.1.4.1.3646.1300.2.15.3.1.14 |
More MIBs from ASKEY
Browse all ASKEYMIBs →The ASKEY-SYSTEM-MIB provides SNMP management interfaces for ASKEY ADSL modems and routers, enabling the monitoring of DSL line parameters such as attenuation, signal-to-noise ratio, and interface status. It facilitates the collection of ADSL-specific performance counters and error statistics required for troubleshooting broadband connectivity issues on vendor hardware.
The ASKEY-ADSL-MIB module enables monitoring and management of ASKEY vendor ADSL modems and DSLAMs by exposing interface statistics, line status, and physical layer parameters via SNMP. It provides specific counters for DSL synchronization states, error rates, and data throughput to facilitate troubleshooting of broadband access links.
The ASKEY-ENTITY-ALARM-MIB extends the standard ENTITY-MIB to define, monitor, and report hardware alarm states and entity status conditions for ASKEY networking devices. It provides specific managed objects for tracking critical system events, such as interface failures, power supply anomalies, and environmental thresholds, within ASKEY-managed infrastructure.
The ASKEY-MCAST-MIB module enables monitoring and configuration of multicast profile parameters on ASKEY network devices, specifically tracking session states, group membership data, and multicast forwarding statistics. This MIB facilitates the management of IP multicast services by exposing OID-based metrics for profile definitions and operational status within the device's multicast routing and switching infrastructure.
The ASKEY-DSLAM-VC-VLAN-MIB enables monitoring and configuration of Virtual Circuit (VC) to Virtual LAN (VLAN) mapping tables on ASKEY DSL Access Multiplexer (DSLAM) hardware via SNMP. It exposes managed objects for tracking the binding relationships between ATM/PPPoE virtual circuits and their corresponding Ethernet VLAN identifiers to ensure proper traffic segregation and service delivery.
The ASKEY-DSLAM-INTERNET-GROUP-MANAGEMENT-PROTOCOL-PROXY-MIB configures and monitors IGMP proxy states and multicast group membership tables on ASKEY DSLAM hardware. It exposes specific metrics for multicast session management, including active group counts, interface bindings, and proxy forwarding status to ensure efficient bandwidth utilization in IPTV and multicast service deployments.