ASCEND-MIBDMTALNET-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for ASCEND-MIBDMTALNET-MIB.
67
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
67 total| Object Name |
|---|
mibdmtAlDslNetworkProfile OBJECT IDENTIFIER .1.3.6.1.4.1.4253.1.10 |
RFC1155-SMI Unknown .1.3.6.1.4.1.4253.1.10 |
mibdmtAlDslNetworkProfileTableA list of mibdmtAlDslNetworkProfile profile entries. SEQUENCE OF MibdmtAlDslNetworkProfileEntry .1.3.6.1.4.1.4253.1.10.1 |
mibdmtAlDslNetworkProfileEntryA mibdmtAlDslNetworkProfile entry containing objects that
maps to the parameters of mibdmtAlDslNetworkProfile profile. MibdmtAlDslNetworkProfileEntry .1.3.6.1.4.1.4253.1.10.1.1 |
dmtAlDslNetworkProfile-Shelf-oro INTEGER .1.3.6.1.4.1.4253.1.10.1.1.1 |
dmtAlDslNetworkProfile-Slot-oro INTEGER .1.3.6.1.4.1.4253.1.10.1.1.2 |
dmtAlDslNetworkProfile-Item-oro INTEGER .1.3.6.1.4.1.4253.1.10.1.1.3 |
dmtAlDslNetworkProfile-NameFor future use. The current design does not use the name field but instead references Cell Based Dmt Adsl lines by the physical address; we may in the future support referencing Cell Based Dmt Adsl lines by name as well as by address. The name consists of a null terminated ascii string supplied by the user; it defaults to the ascii form of the Cell Based Dmt Adsl line physical address.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4253.1.10.1.1.4 |
dmtAlDslNetworkProfile-PhysicalAddress-ShelfThe number of the shelf that the addressed physical device resides on.rw Enumeration .1.3.6.1.4.1.4253.1.10.1.1.5 |
dmtAlDslNetworkProfile-PhysicalAddress-SlotThe number of the slot that the addressed physical device resides on.rw Enumeration .1.3.6.1.4.1.4253.1.10.1.1.6 |
dmtAlDslNetworkProfile-PhysicalAddress-ItemNumberA number that specifies an addressable entity within the context of shelf and slot.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.7 |
dmtAlDslNetworkProfile-EnabledTRUE if the line is enabled, otherwise FALSE.rw Enumeration .1.3.6.1.4.1.4253.1.10.1.1.8 |
dmtAlDslNetworkProfile-ProfileNumberFor potential backwards compatibility. The current design consists of one line profile numbered 0.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.9 |
dmtAlDslNetworkProfile-LineConfig-NailedGroupA number that identifies the set of lines that makes up a nailed group. 0 means this line is not part of a nailed group.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.11 |
dmtAlDslNetworkProfile-LineConfig-RateAdaptModeUpThe up stream rate adaptive mode of operation. ONLY OPERATOR_CONTROLLED and AUTOMATIC_AT_STARTUP are currently supported.rw Enumeration .1.3.6.1.4.1.4253.1.10.1.1.19 |
dmtAlDslNetworkProfile-LineConfig-RateAdaptModeDownThe down stream rate adaptive mode of operation. ONLY OPERATOR_CONTROLLED and AUTOMATIC_AT_STARTUP are currently supported.rw Enumeration .1.3.6.1.4.1.4253.1.10.1.1.20 |
dmtAlDslNetworkProfile-LineConfig-RateAdaptRatioUpThe ratio in percent of excess bitrate distribution over the up stream fast and interleaved latencies. 100% - fast path , 0% - interleaved path. Valid ONLY in rate-adapt-mode = AUTOMATIC_AT_STARTUP or DYNAMIC .rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.21 |
dmtAlDslNetworkProfile-LineConfig-RateAdaptRatioDownThe ratio in percent of excess bitrate distribution over the down stream fast and interleaved latencies. 100% - fast path , 0% - interleaved path. Valid ONLY in rate-adapt-mode = AUTOMATIC_AT_STARTUP or DYNAMIC .rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.22 |
dmtAlDslNetworkProfile-LineConfig-MaxPowerSpectralDensityThe power spectral density in dBm/Hz allowed on the line. Decreasing the value may reduce capacity. Defined for downstream only. Actual value is negative.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.25 |
dmtAlDslNetworkProfile-FastPathConfig-MinBitrateUpThe up stream minimum requested bitrate, in Kbps. NOT valid in rate-adapt-mode = OPERATOR_CONTROLLED.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.26 |
dmtAlDslNetworkProfile-FastPathConfig-MinBitrateDownThe down stream minimum requested bitrate, in Kbps. NOT valid in rate-adapt-mode = OPERATOR_CONTROLLED.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.27 |
dmtAlDslNetworkProfile-FastPathConfig-MaxBitrateUpThe up stream maximum requested bitrate, in Kbps. NOT valid in rate-adapt-mode = OPERATOR_CONTROLLED.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.28 |
dmtAlDslNetworkProfile-FastPathConfig-MaxBitrateDownThe down stream maximum requested bitrate, in Kbps. NOT valid in rate-adapt-mode = OPERATOR_CONTROLLED.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.29 |
dmtAlDslNetworkProfile-FastPathConfig-PlannedBitrateUpThe up stream rate that will be used, in Kbps. ONLY valid in rate-adapt-mode = OPERATOR_CONTROLLED.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.30 |
dmtAlDslNetworkProfile-FastPathConfig-PlannedBitrateDownThe down stream rate that will be used, in Kbps. ONLY valid in rate-adapt-mode = OPERATOR_CONTROLLED.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.31 |
dmtAlDslNetworkProfile-InterleavePathConfig-MinBitrateUpThe up stream minimum requested bitrate, in Kbps. NOT valid in rate-adapt-mode = OPERATOR_CONTROLLED.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.32 |
dmtAlDslNetworkProfile-InterleavePathConfig-MinBitrateDownThe down stream minimum requested bitrate, in Kbps. NOT valid in rate-adapt-mode = OPERATOR_CONTROLLED.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.33 |
dmtAlDslNetworkProfile-InterleavePathConfig-MaxBitrateUpThe up stream maximum requested bitrate, in Kbps. NOT valid in rate-adapt-mode = OPERATOR_CONTROLLED.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.34 |
dmtAlDslNetworkProfile-InterleavePathConfig-MaxBitrateDownThe down stream maximum requested bitrate, in Kbps. NOT valid in rate-adapt-mode = OPERATOR_CONTROLLED.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.35 |
dmtAlDslNetworkProfile-InterleavePathConfig-PlannedBitrateUpThe up stream rate that will be used, in Kbps. ONLY valid in rate-adapt-mode = OPERATOR_CONTROLLED.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.36 |
dmtAlDslNetworkProfile-InterleavePathConfig-PlannedBitrateDownThe down stream rate that will be used, in Kbps. ONLY valid in rate-adapt-mode = OPERATOR_CONTROLLED.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.37 |
dmtAlDslNetworkProfile-InterleavePathConfig-MaxDelayUpThe maximum allowed up stream interleaver induced delay, in msec.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.38 |
dmtAlDslNetworkProfile-InterleavePathConfig-MaxDelayDownThe maximum allowed down stream interleaver induced delay, in msec.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.39 |
dmtAlDslNetworkProfile-MarginConfig-TargetNoiseMarginUpThe up stream noise margin in dB that the modem shall achieve relative to BER 10^-7.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.40 |
dmtAlDslNetworkProfile-MarginConfig-TargetNoiseMarginDownThe down stream noise margin in dB that the modem shall achieve relative to BER 10^-7.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.41 |
dmtAlDslNetworkProfile-MarginConfig-MinNoiseMarginUpThe up stream minimum noise margin in dB that the modem shall tolerate relative to BER 10^-7. If current noise margin falls below this level the ATU shall attempt to increase far-end output power to get margin above this limit, by means of bit swapping.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.42 |
dmtAlDslNetworkProfile-MarginConfig-MinNoiseMarginDownThe down stream minimum noise margin in dB that the modem shall tolerate relative to BER 10^-7. If current noise margin falls below this level the ATU shall attempt to increase far-end output power to get margin above this limit, by means of bit swapping.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.43 |
dmtAlDslNetworkProfile-MarginConfig-MaxAddNoiseMarginUpThe up stream maximum noise margin in dB on top of the target-noise-margin that the modem shall tolerate relative to BER 10^-7. If current noise margin is above this level the ATU shall attempt to reduce far-end output power to get margin below this limit, by means of bit swapping.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.44 |
dmtAlDslNetworkProfile-MarginConfig-MaxAddNoiseMarginDownThe down stream maximum noise margin in dB on top of the target-noise-margin that the modem shall tolerate relative to BER 10^-7. If current noise margin is above this level the ATU shall attempt to reduce far-end output power to get margin below this limit, by means of bit swapping.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.45 |
dmtAlDslNetworkProfile-MarginConfig-RaDownshiftMarginUpValid ONLY in rate-adapt-mode = DYNAMIC. In dB. If current up stream noise margin is below this parameter for more than ra-downshift-int-up sec, modem shall attemp to rate adapt (bitrate down).rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.46 |
dmtAlDslNetworkProfile-MarginConfig-RaDownshiftIntUpValid ONLY in rate-adapt-mode = DYNAMIC. In seconds. If current up stream noise margin is below ra-downshift-margin-up for more than this, modem shall attemp to rate adapt (bitrate down).rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.47 |
dmtAlDslNetworkProfile-MarginConfig-RaDownshiftMarginDownValid ONLY in rate-adapt-mode = DYNAMIC. In dB. If current down stream noise margin is below this parameter for more than ra-downshift-int-down sec, modem shall attemp to rate adapt (bitrate down).rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.48 |
dmtAlDslNetworkProfile-MarginConfig-RaDownshiftIntDownValid ONLY in rate-adapt-mode = DYNAMIC. In seconds. If current down stream noise margin is below ra-downshift-margin-down for more than this, modem shall attemp to rate adapt (bitrate down).rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.49 |
dmtAlDslNetworkProfile-MarginConfig-RaUpshiftMarginUpValid ONLY in rate-adapt-mode = DYNAMIC. In dB. If current up stream noise margin is above this parameter for more than ra-downshift-int-up sec, modem shall attemp to rate adapt (bitrate up).rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.50 |
dmtAlDslNetworkProfile-MarginConfig-RaUpshiftIntUpValid ONLY in rate-adapt-mode = DYNAMIC. In seconds. If current up stream noise margin is above ra-downshift-margin-up for more than this, modem shall attemp to rate adapt (bitrate up).rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.51 |
dmtAlDslNetworkProfile-MarginConfig-RaUpshiftMarginDownValid ONLY in rate-adapt-mode = DYNAMIC. In dB. If current down stream noise margin is above this parameter for more than ra-downshift-int-down sec, modem shall attemp to rate adapt (bitrate up).rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.52 |
dmtAlDslNetworkProfile-MarginConfig-RaUpshiftIntDownValid ONLY in rate-adapt-mode = DYNAMIC. In seconds. If current down stream noise margin is above ra-downshift-margin-down for more than this, modem shall attemp to rate adapt (bitrate up).rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.53 |
dmtAlDslNetworkProfile-Action-orw Enumeration .1.3.6.1.4.1.4253.1.10.1.1.54 |
dmtAlDslNetworkProfile-LineConfig-VpSwitchingVpiThe Vpi to be used for the VP switching. Rest of the VPIs within valid vpi-vci-range will be used for the VC switching. Changes in this range will take effect immediately. THE USER SHOULD BE VERY CAREFUL WHILE CHANGING THIS VALUE BECAUSE ALL CONNECTIONS ON THE LIM WHERE THIS PORT BELONGS WILL BE DROPPED IN ORDER TO MAKE THIS NEW VALUE EFFECTIVE IMMEDIATELY.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.55 |
dmtAlDslNetworkProfile-LineConfig-MaxAggrPowerLevelUpThe maximum aggregate output power in dBm allowed on the line in the up stream direction. Increasing value may result in capacity boosting.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.56 |
dmtAlDslNetworkProfile-LineConfig-MaxAggrPowerLevelDownThe maximum aggregate output power in dBm allowed on the line in the down stream direction. Increasing value may result in capacity boosting.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.57 |
dmtAlDslNetworkProfile-LineConfig-LineCodeThe DMT line code is used for the training. NOTE: for the ADSL 12-ports LIM card only (which uses the ALCATEL chipset), setting the line code to ansi-dmt will provide better line rate than auto-select for an ansi-dmt link. Therefore, set the line code to ansi-dmt for an ansi-dmt link to obtain optimal rate.rw Enumeration .1.3.6.1.4.1.4253.1.10.1.1.58 |
dmtAlDslNetworkProfile-LineConfig-LineLatencyDownThe DMT line latency to be used for the downstream data transport.rw Enumeration .1.3.6.1.4.1.4253.1.10.1.1.59 |
dmtAlDslNetworkProfile-LineConfig-LineLatencyUpThe DMT line latency to be used for the upstream data transport.rw Enumeration .1.3.6.1.4.1.4253.1.10.1.1.60 |
dmtAlDslNetworkProfile-LineConfig-TrellisEncodingTRUE if trellis encoding is to be enabled, FALSE otherwise.rw Enumeration .1.3.6.1.4.1.4253.1.10.1.1.61 |
dmtAlDslNetworkProfile-LineConfig-GainDefaultThe default gain value in db to be used for the AGC.rw Enumeration .1.3.6.1.4.1.4253.1.10.1.1.62 |
dmtAlDslNetworkProfile-SparingModePort sparing operational mode for this port.rw Enumeration .1.3.6.1.4.1.4253.1.10.1.1.63 |
dmtAlDslNetworkProfile-LineConfig-UpstreamStartBinThe starting upstream frequency bin.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.64 |
dmtAlDslNetworkProfile-LineConfig-UpstreamEndBinThe ending upstream frequency bin.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.65 |
dmtAlDslNetworkProfile-LineConfig-DownstreamStartBinThe starting downstream frequency bin.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.66 |
dmtAlDslNetworkProfile-LineConfig-DownstreamEndBinThe ending downstream frequency bin.rw INTEGER .1.3.6.1.4.1.4253.1.10.1.1.67 |
dmtAlDslNetworkProfile-LineConfig-LoopBackConfiguration of different modem loopbacks.rw Enumeration .1.3.6.1.4.1.4253.1.10.1.1.69 |
dmtAlDslNetworkProfile-LineConfig-BitSwappingControls wether Bit-Swapping is enabled or no. On 12 port DMT card and 48 port G.lite card has not effect.rw Enumeration .1.3.6.1.4.1.4253.1.10.1.1.70 |
dmtAlDslNetworkProfile-LineConfig-FbmDbmModeControls wether the line is in Fixed-Bit-Map or Dual-Bit-Map mode. Only relevant for Annex-C cards.rw Enumeration .1.3.6.1.4.1.4253.1.10.1.1.71 |
dmtAlDslNetworkProfile-ThreshProfileThe name of the DSL-THRESHOLD profile which applies to this ADSL line.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4253.1.10.1.1.72 |
dmtAlDslNetworkProfile-IgnoreLineupIgnore line up value for this port.rw Enumeration .1.3.6.1.4.1.4253.1.10.1.1.73 |
dmtAlDslNetworkProfile-LineConfig-AlcatelUs413BoostProvides an increase in upstream rate in T1.413 mode for 24/48 Port Annex A boards based on the Globespan chip set when connected to an Alcatel CPE. Irrelevant for any other situtation. Use with extreme caution.rw Enumeration .1.3.6.1.4.1.4253.1.10.1.1.74 |