ARRIS-D5-SOFTWARE-MGR-MIB
AI MIB Summary
The ARRIS-D5-SOFTWARE-MGR-MIB enables SNMP-based monitoring and management of firmware versions, installation status, and upgrade procedures for ARRIS EdgeQAM hardware. It provides specific metrics for software image integrity, active release identification, and the execution state of software maintenance operations on these DOCSIS 3.0/3.1 edge QAM devices.
This MIB manages the software on the ARRIS EdgeQAM products
Main OID:
softwareManagerMIB.1.3.6.1.4.1.4115.1.8.1.10
39
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
39 total| Object Name |
|---|
softwareManagerMIBThis MIB manages the software on the ARRIS EdgeQAM products MODULE-IDENTITY .1.3.6.1.4.1.4115.1.8.1.10 |
smControlGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.8.1.10.1 |
smReloadActionForce a reload of the ARRIS product. The command is applied to both WANs when equipped. The load marked as boot in the Software Table will be loaded. nil(1) - Do nothing reloadConfigSave(2) - Saves the current configuration before reloading reloadNoConfigSave(3) - Reloads without saving configurationrw Enumeration .1.3.6.1.4.1.4115.1.8.1.10.1.1 |
smConfigFileActionPerform various actions on the configuration file, as directed below. nil(1) - Do nothing saveRunningConfig(2) - Copies the running configuration to the startup configuration. eraseStartupConfig(3) - Erases the startup configuration. You may want to do this before a reboot (without config file save) to get a default configured system. uploadStartupConfigToServer(4) - Using the server information in the configFileTransfer group, this will upload the current startup-configuration to the default directory on the server. If you need upload directory control, use the configFileTransferrw Enumeration .1.3.6.1.4.1.4115.1.8.1.10.1.2 |
smSoftwareListGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.8.1.10.2 |
smSoftwareListTableTable of images installed on the flash disk SEQUENCE OF SmSoftwareListEntry .1.3.6.1.4.1.4115.1.8.1.10.2.1 |
smSoftwareListEntry. SmSoftwareListEntry .1.3.6.1.4.1.4115.1.8.1.10.2.1.1 |
smSoftwareEntryIndeximage index Unsigned32 .1.3.6.1.4.1.4115.1.8.1.10.2.1.1.1 |
smSoftwareEntryFilenameName of the image filero OCTET STRING .1.3.6.1.4.1.4115.1.8.1.10.2.1.1.2 |
smSoftwareEntryVersionimage versionro OCTET STRING .1.3.6.1.4.1.4115.1.8.1.10.2.1.1.3 |
smSoftwareEntryDateDate image createdro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.4115.1.8.1.10.2.1.1.4 |
smSoftwareEntryStateState of the load file. valid means the software load has been properly downloaded and can be loaded onto the system. corrupt means there was a problem tranferring the load and it cannot be loaded onto the system. unknown means that the software load has not yet been validated by the system, and may or may not be valid.ro Enumeration .1.3.6.1.4.1.4115.1.8.1.10.2.1.1.5 |
smSoftwareEntrySizefile sizero Integer32 .1.3.6.1.4.1.4115.1.8.1.10.2.1.1.6 |
smSoftwareEntryStatusStatus of software may be running-boot, running, boot or inactive running-boot(1) indicates that the load is running AND is the boot load. running(2) means the software is currently running on the box, but is not the boot load. boot(3) means that the selected load will boot on next restart. Confirm by checking ksSMBootFileName. inactive(4) indicates the load is neither running nor set to boot.ro Enumeration .1.3.6.1.4.1.4115.1.8.1.10.2.1.1.7 |
smSoftwareEntryActionPerform an action on this software load entry. To make the current software load the boot load, select makeBoot(2). When set to upload(3), this software load will be sent to the server using the settings specified in the softwareDownloadGroup MIB objects. This method cannot specify an upload path on the server for the software load. The load will appear in the default directory on the server for the specified transfer protocol. For control over the upload path, please use the smSoftwareDownloadGroup directly. Selecting delete(4) will delete the load from the system.rw Enumeration .1.3.6.1.4.1.4115.1.8.1.10.2.1.1.8 |
smConfigFileListGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.8.1.10.3 |
smConfigFileListTableTable of configuration files or scripts on flash disk SEQUENCE OF SmConfigFileListEntry .1.3.6.1.4.1.4115.1.8.1.10.3.1 |
smConfigFileListEntry. SmConfigFileListEntry .1.3.6.1.4.1.4115.1.8.1.10.3.1.1 |
smConfigFileEntryIndeximage index Unsigned32 .1.3.6.1.4.1.4115.1.8.1.10.3.1.1.1 |
smConfigFileEntryNameName of the filero OCTET STRING .1.3.6.1.4.1.4115.1.8.1.10.3.1.1.2 |
smConfigFileTimestampTimestamp of the configuration filero DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.4115.1.8.1.10.3.1.1.3 |
smConfigFileEntryActionActions to perform on the current configuration file. To make this configuration file the startup configuration file, select makeStartupConfig(2). Be sure not to overwrite the new startup-configuration when reloading the system. To copy the current configuration file into the running configuration, select copyIntoRunningConfig(3). Don't forget to save the new running configuration if necessary. When set to upload(4), this software load will be sent to the server using the settings specified in the smConfigFileDownloadGroup MIB objects. This method cannot specify an upload path on the server for the software load. The load will appear in the default directory on the server for the specified transfer protocol. For control over the upload path, please use the smConfigFileDownloadGroup directly. Finally, to delete the configuration file, select delete(5).rw Enumeration .1.3.6.1.4.1.4115.1.8.1.10.3.1.1.4 |
smSoftwareTransferGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.8.1.10.4 |
smSoftwareTransferDeviceSpecify protocol to use for software load transfersrw Enumeration .1.3.6.1.4.1.4115.1.8.1.10.4.1 |
smSoftwareTransferHostnameServer ip address or hostnamerw OCTET STRING .1.3.6.1.4.1.4115.1.8.1.10.4.2 |
smSoftwareTransferUsernameServer user namerw OCTET STRING .1.3.6.1.4.1.4115.1.8.1.10.4.3 |
smSoftwareTransferPasswordServer user passwordrw OCTET STRING .1.3.6.1.4.1.4115.1.8.1.10.4.4 |
smSoftwareTransferPathPath and filename for image file on tftp, ftp or nfsrw OCTET STRING .1.3.6.1.4.1.4115.1.8.1.10.4.5 |
smSoftwareTransferControlControl the transfer as follows: abort(1) - Will abort the transfer in progress. download(2) - Starts a transfer to the ARRIS device upload(3) - Transfer specified load to the server downloadAsBoot(4) will download the software image to the ARRIS device and make it the next boot imagerw Enumeration .1.3.6.1.4.1.4115.1.8.1.10.4.6 |
smSoftwareTransferStatusIndication of the last transfer attempt as follows: none(1) indicates no images have been transferred since the system rebooted. inprogress(2) - Indicates there is an active transfer occurring. finished(3) - Indicates the transfer is complete. filenameError(4) - Indicates there was a problem with either the path and/or filename, or the wrong server was specified and the file was not found. hostnameError(5) - Indicates a problem where the hostname could not be resolved, or an incorrectly formatted IP address was specified.ro Enumeration .1.3.6.1.4.1.4115.1.8.1.10.4.7 |
smConfigFileTransferGroup OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.8.1.10.5 |
smConfigFileTransferDeviceSpecify protocol to use for file transfersrw Enumeration .1.3.6.1.4.1.4115.1.8.1.10.5.1 |
smConfigFileTransferHostnameServer ip address or hostnamerw OCTET STRING .1.3.6.1.4.1.4115.1.8.1.10.5.2 |
smConfigFileTransferUsernameServer user namerw OCTET STRING .1.3.6.1.4.1.4115.1.8.1.10.5.3 |
smConfigFileTransferPasswordServer user passwordrw OCTET STRING .1.3.6.1.4.1.4115.1.8.1.10.5.4 |
smConfigFileTransferPathPath and filename of the configuration file on the source device.rw OCTET STRING .1.3.6.1.4.1.4115.1.8.1.10.5.5 |
smConfigFileTransferTargetPathPath and filename of the configuration file on the target device.rw OCTET STRING .1.3.6.1.4.1.4115.1.8.1.10.5.6 |
smConfigFileTransferControlControl the transfer as follows: abort(1) - Will abort the transfer in progress. download(2) - Starts a transfer to the ARRIS device upload(3) - Transfer specified file to the server downloadAsStartup(4) Transfer the config file and make it the startup configurationrw Enumeration .1.3.6.1.4.1.4115.1.8.1.10.5.7 |
smConfigFileTransferStatusIndication of the last transfer attempt as follows: none(1) indicates no files have been transferred since the system rebooted. inprogress(2) - Indicates there is an active transfer occurring. finished(3) - Indicates the transfer is complete. filenameError(4) - Indicates there was a problem with either the path and/or filename, or the wrong server was specified and the file was not found. hostnameError(5) - Indicates a problem where the hostname could not be resolved, or an incorrectly formatted IP address was specified.ro Enumeration .1.3.6.1.4.1.4115.1.8.1.10.5.8 |