ARRIS-D5-QAM-MIB
AI MIB Summary
The ARRIS-D5-QAM-MIB enables monitoring and configuration of QAM modulation parameters, channel states, and signal quality metrics on Arris D5 series Universal Edge QAM (UEQ) modulators. It provides granular visibility into RF channel occupancy, error rates, and modulation profiles essential for maintaining cable network transmission integrity.
Arris D5 UEQ QAM Management MIB
Main OID:
d5QamMib.1.3.6.1.4.1.4115.1.8.1.5
64
Objects
Active
Status
9
Dependencies
Imported Objects
Objects
64 total| Object Name |
|---|
d5QamMibArris D5 UEQ QAM Management MIB MODULE-IDENTITY .1.3.6.1.4.1.4115.1.8.1.5 |
d5QamRFObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.8.1.5.1 |
d5QamRFChannelTableThis table extends docsIfDownstreamChannelTable with extra
RF properties. SEQUENCE OF D5QamRFChannelEntry .1.3.6.1.4.1.4115.1.8.1.5.1.1 |
d5QamRFChannelEntryAn entry for a D5 QAM Channel RF Properties D5QamRFChannelEntry .1.3.6.1.4.1.4115.1.8.1.5.1.1.1 |
d5QamRFChannelAnnexThe value of this object indicates the conformance of
the implementation to important regional cable standards.
annexA : Annex A from ITU-J83 is used.
annexB : Annex B from ITU-J83 is used.
annexC : Annex C from ITU-J83 is used.rw Enumeration .1.3.6.1.4.1.4115.1.8.1.5.1.1.1.1 |
d5QamRFChannelFrequencyThe center of the downstream frequency associated with
this channel.rw Unsigned32 UNITS "hertz" .1.3.6.1.4.1.4115.1.8.1.5.1.1.1.2 |
d5QamRFChannelModulationThe modulation type associated with this downstream
channel.rw Enumeration .1.3.6.1.4.1.4115.1.8.1.5.1.1.1.3 |
d5QamRFChannelFECInterleaverLevelThis value contains the interleaving level in Annex B standard.
Level 1 (static) is specified for 64-QAM transmission only. This
mode accommodates the installed based of legacy 64-QAM only
digital set top. While in this level, a single interleaving depth
is supported, nameley I=128, J=1.
Level 2 (variable) encompasses both 64-QAM and 256-QAM transmissions
and is capable of supporting variable interleaving, whose depth is
specified in d5QamRFChannelFECInterleaverModerw Enumeration .1.3.6.1.4.1.4115.1.8.1.5.1.1.1.4 |
d5QamRFChannelFECInterleaverModeThis value contain the control word representing a
specific interleaving depth for Annex B level 2 (variable)
interleaving standard, which is one of the following:
0 - I=128 J=1
1 - I=128 J=1
2 - I=128 J=2
3 - I=64 J=2
4 - I=128 J=3
5 - I=32 J=4
6 - I=128 J=4
7 - I=16 J=8
8 - I=128 J=5
9 - I=8 J=16
10 - I=128 J=6
11 - reserved
13 - I=128 J=6
12 - I=128 J=7
14 - I=128 J=8
15 - reserved
16 - reservedrw INTEGER (0..10 | 12..14) .1.3.6.1.4.1.4115.1.8.1.5.1.1.1.5 |
d5QamRFChannelPowerthe transmit power associated with this channel.rw TenthdBmV UNITS "dBmV" .1.3.6.1.4.1.4115.1.8.1.5.1.1.1.6 |
d5QamRFChannelSpectralInversiontrue(1) if QAM Channel carrier spectrum is invertedrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4115.1.8.1.5.1.1.1.7 |
d5QamRFChannelSymbolRateSymbol rate of current transmission, this value is fixed for
64-QAM and 256-QAM transmission in Annex B standard.
It is variable in Annex A standard and can only be changed
while in this mode.rw Unsigned32 .1.3.6.1.4.1.4115.1.8.1.5.1.1.1.8 |
d5QamRFChannelWidthThe distance between the center frequencies of the downstream frequency associated with
this channel.rw Unsigned32 .1.3.6.1.4.1.4115.1.8.1.5.1.1.1.9 |
d5QamRFChannelRowStatusThe RowStatus for controlling entries in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4115.1.8.1.5.1.1.1.99 |
d5QamStatObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.8.1.5.3 |
d5QamStatProgramCounterTableThis table contains counters of all MPEG packets whose PIDs
are associated with a program currently being streamed through
a QAM interface SEQUENCE OF D5QamStatProgramCounterEntry .1.3.6.1.4.1.4115.1.8.1.5.3.1 |
d5QamStatProgramCounterEntryAn entry for a single program stream on a QAM interface D5QamStatProgramCounterEntry .1.3.6.1.4.1.4115.1.8.1.5.3.1.1 |
d5QamStatProgramCounterQamIfIndexQAM interface associated with program stream.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4115.1.8.1.5.3.1.1.1 |
d5QamStatProgramCounterProgramProgram Number of program stream.ro D5Program .1.3.6.1.4.1.4115.1.8.1.5.3.1.1.2 |
d5QamStatProgramCounterPacketsCount of all MPEG packets associated with the program stream.ro Counter32 .1.3.6.1.4.1.4115.1.8.1.5.3.1.1.3 |
d5QamSpareObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.8.1.5.4 |
d5QamSpareGroupTableThis table contains QAM physical entities that are part of
redundancy spare groups. Spare groups are identified by the
spare entity itself through its physical index. A group must
contain 1 to N primaries QAM entities allowing 1:1 or 1:N
redundancy ability. SEQUENCE OF D5QamSpareGroupEntry .1.3.6.1.4.1.4115.1.8.1.5.4.1 |
d5QamSpareGroupEntryEach entry describe a single QAM physical entity and its
relationship to and role within a spare group. D5QamSpareGroupEntry .1.3.6.1.4.1.4115.1.8.1.5.4.1.1 |
d5QamSpareGroupPrimaryPhysicalIndexThe Physical Index of the QAM entity.ro PhysicalIndex (ENTITY-MIB) .1.3.6.1.4.1.4115.1.8.1.5.4.1.1.1 |
d5QamSpareGroupSparePhysicalIndexThe Physical Index of the QAM spare entity. Spare must
identify itself.rw PhysicalIndex (ENTITY-MIB) .1.3.6.1.4.1.4115.1.8.1.5.4.1.1.2 |
d5QamSpareGroupFailbackModeMust be 'none' for primary entities. For spare entities, it
defines the failback mode when the fault has cleared.rw Enumeration .1.3.6.1.4.1.4115.1.8.1.5.4.1.1.3 |
d5QamSpareGroupFailoverStatusThe status of this physical entity in spare group.
active: indicates that a primary entity is running normally.
indicates that a spare entity has been failed over.
standby: indicates that spare entity is standing by.
switched: indicates that a primary entity has failed over
to spare.
fail: indicates that either primary or spare are not
in service.ro Enumeration .1.3.6.1.4.1.4115.1.8.1.5.4.1.1.4 |
d5QamSpareGroupRowStatusThe RowStatus for controlling entries in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4115.1.8.1.5.4.1.1.99 |
d5QamSpareGroupTraps OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.8.1.5.4.2 |
d5QamSpareGroupFailOverThis event signifies that a primary QAM physical entity has
been switched over to its spare. NOTIFICATION-TYPE .1.3.6.1.4.1.4115.1.8.1.5.4.2.1 |
d5QamSpareGroupFailBackThis event signifies that a primary QAM physical entity is
no longer switched over to spare, which has been restored to
stand-by duty. NOTIFICATION-TYPE .1.3.6.1.4.1.4115.1.8.1.5.4.2.2 |
d5QamDocsisObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.8.1.5.5 |
d5QamDocsisChannelTableThis table extends docsIfDownstreamChannelTable with DOCSIS
properties. SEQUENCE OF D5QamDocsisChannelEntry .1.3.6.1.4.1.4115.1.8.1.5.5.1 |
d5QamDocsisChannelEntryAn entry for a D5 QAM Channel DOCSIS Properties D5QamDocsisChannelEntry .1.3.6.1.4.1.4115.1.8.1.5.5.1.1 |
d5QamDocsisChannelDtiOffsetDOCSIS Timing Interface: offset to be added to egress SYNC
timestamp messages.rw INTEGER (-30000..30000) UNITS "ticks" .1.3.6.1.4.1.4115.1.8.1.5.5.1.1.1 |
d5QamMonitorObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.8.1.5.6 |
d5QamSnoopObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.8.1.5.6.1 |
d5QamSnoopTableThis table lists of QAM channels under snoop. SEQUENCE OF D5QamSnoopEntry .1.3.6.1.4.1.4115.1.8.1.5.6.1.1 |
d5QamSnoopEntryAn entry for a single D5 QAM channel snoop D5QamSnoopEntry .1.3.6.1.4.1.4115.1.8.1.5.6.1.1.1 |
d5QamSnoopProbeThis value returns the probe type for snooping, which can
be one of:
post-mux: probe after muxing stage and before RF modulation
post-rf: probe after RF modulation using builtin demodulatorro Enumeration .1.3.6.1.4.1.4115.1.8.1.5.6.1.1.1.1 |
d5QamSnoopTSIDAfter row creation, this value is read only and returns the
current Transport Stream Identifier for this QAM channel.
On row creation, if this value is non-zero, it will be used as
an alternative identifier to ifIndex for the QAM channel;
in which case, ifIndex must be 0.rw Unsigned32 .1.3.6.1.4.1.4115.1.8.1.5.6.1.1.1.2 |
d5QamSnoopEncapsulationThe value contains the encapsulation type for snooped data.rw Enumeration .1.3.6.1.4.1.4115.1.8.1.5.6.1.1.1.3 |
d5QamSnoopIpSrcThis value returns the source IP address of snooped packetsro IpAddress .1.3.6.1.4.1.4115.1.8.1.5.6.1.1.1.4 |
d5QamSnoopPortSrcThis value returns the source port of snooped packetsro Unsigned32 .1.3.6.1.4.1.4115.1.8.1.5.6.1.1.1.5 |
d5QamSnoopIpDestThis value contains the target IP address of snooped packetsrw IpAddress .1.3.6.1.4.1.4115.1.8.1.5.6.1.1.1.6 |
d5QamSnoopPortDestThis value contains the target port of snooped packetsrw Unsigned32 .1.3.6.1.4.1.4115.1.8.1.5.6.1.1.1.7 |
d5QamSnoopRowStatusThe RowStatus for controlling entries in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4115.1.8.1.5.6.1.1.1.99 |
d5QamSnoopTOSThe value is used to fill in the Type Of Service field for egress
IP packets containing snooped data.rw Unsigned32 .1.3.6.1.4.1.4115.1.8.1.5.6.1.2 |
d5QamSnoopVlanPriorityThe value is used to fill in the VLAN priority field for egress
Ethernet frames containing snooped IP packets.rw Unsigned32 .1.3.6.1.4.1.4115.1.8.1.5.6.1.3 |
d5QamRFSignalObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.8.1.5.6.2 |
d5QamRFSignalQualityTableThis table lists signal quality for QAM channels. SEQUENCE OF D5QamRFSignalQualityEntry .1.3.6.1.4.1.4115.1.8.1.5.6.2.1 |
d5QamRFSignalQualityEntryAn entry for a single D5 QAM channel D5QamRFSignalQualityEntry .1.3.6.1.4.1.4115.1.8.1.5.6.2.1.1 |
d5QamRFSigQMeasureControlThis value indicates wether on-board demodulator scans this
channel for RF signal quality measurement.rw Enumeration .1.3.6.1.4.1.4115.1.8.1.5.6.2.1.1.1 |
d5QamRFSigQMeasureDelayThis value contains the amount of time in milliseconds the
demodulator stay on this channel once it has acquired a lock.
The longer the time, the more relevant the measurement, a
value of zero means that only lock status will be a meaningful
measurement.rw Unsigned32 UNITS "ms" .1.3.6.1.4.1.4115.1.8.1.5.6.2.1.1.2 |
d5QamRFSigQMpegLockThis value returns whether the on-board demodulator has
acquired a full MPEG lock the last time if was scanning this
channel.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4115.1.8.1.5.6.2.1.1.3 |
d5QamRFSigQBitErrorRateThis value returns the bit error rate measured during the
last scan period. This value is in the order of 10E-08.ro Gauge32 .1.3.6.1.4.1.4115.1.8.1.5.6.2.1.1.4 |
d5QamRFSigQUnerroredsThe value returns the accumulated count of unerrored codewords
for all previous scan periods since this counter was cleared.ro Counter32 .1.3.6.1.4.1.4115.1.8.1.5.6.2.1.1.5 |
d5QamRFSigQCorrectedsThe value returns the accumulated count of corrected codewords
for all previous scan periods since this counter was cleared.ro Counter32 .1.3.6.1.4.1.4115.1.8.1.5.6.2.1.1.6 |
d5QamRFSigQUncorrectablesThe value returns the accumulated count of uncorrected codewords
for all previous scan periods since this counter was cleared.ro Counter32 .1.3.6.1.4.1.4115.1.8.1.5.6.2.1.1.7 |
d5QamRFSigQSignalNoiseThis value returns the Signal To Noise ratio measured during
the last scan period.ro TenthdB UNITS "dB" .1.3.6.1.4.1.4115.1.8.1.5.6.2.1.1.8 |
d5QamConformance OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.8.1.5.99 |
d5QamObjectGroups OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.8.1.5.99.1 |
d5QamNotificationGroups OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.8.1.5.99.2 |
d5QamCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.8.1.5.99.3 |
More MIBs from Arris International
Browse all Arris InternationalMIBs →ARRIS-D5-VIDEO-MIB
The ARRIS-D5-VIDEO-MIB provides SNMP management interfaces for monitoring and controlling MPEG video transport streams and associated software processes on Arris DOCSIS 3.0/3.1 Cable Modem Termination Systems (CMTS). It exposes operational metrics for video channel status, stream health, and MPEG protocol state transitions to ensure reliable multicast video delivery over the cable network.
391 objects→
CADANT-CMTS-SYSTEM-MIB
The CADANT-CMTS-SYSTEM-MIB provides management access to Arris E6000 Cable Modem Termination System (CMTS) hardware parameters and system constants, enabling the monitoring of critical device states such as CPU utilization, memory usage, temperature sensors, and interface operational status. This module facilitates the collection of system-level telemetry required for capacity planning, fault isolation, and performance analysis within DOCSIS-based cable networks.
338 objects→
CADANT-CMTS-MAC-MIB
The CADANT-CMTS-MAC-MIB provides vendor-specific extensions for Cadant CMTS hardware to map DOCSIF-MIB CM status indices to MAC address tables, enabling precise tracking of cable modem registration states, signal quality metrics, and interface bindings. This module facilitates granular troubleshooting of subscriber connectivity by correlating physical MAC addresses with logical DOCSIS session parameters on the upstream and downstream channels.
307 objects→
ARRIS-CER-VIDEO-MIB
The ARRIS-CER-VIDEO-MIB provides SNMP management capabilities for monitoring and controlling MPEG video software processes and parameters on Arris Cable Edge Router (CER) platforms. It enables the tracking of video session states, stream quality metrics, and encoder/decoder operational status to ensure reliable content delivery.
299 objects→
CADANT-CMTS-EQUIPMENT-MIB
The CADANT-CMTS-EQUIPMENT-MIB facilitates the remote provisioning, diagnostic testing, and auditing configuration of Arris E6 Cable Modem Termination System (CMTS) hardware, specifically managing card and port states while handling equipment-related trap notifications.
254 objects→
CADANT-HW-MEAS-MIB
The CADANT-HW-MEAS-MIB aggregates hardware-specific counter metrics for the ARRIS C4 Cable Modem Termination System (CMTS), including standard hardware statistics grouped for engineering analysis. This module facilitates the monitoring of physical device health and resource utilization within the Cadant-managed C4 platform.
192 objects→