ARRIS-C3-MAC-MIB
AI MIB Summary
The ARRIS-C3-MAC-MIB module provides SNMP-based management and monitoring of the Media Access Control (MAC) layer software components within the Cadant C3 Cable Modem Termination System (CMTS). It exposes specific metrics for tracking MAC interface states, error counters, and protocol statistics essential for maintaining DOCSIS service integrity on ARRIS hardware.
This MIB manages the MAC software on the Cadant C3 CMTS.
Main OID:
cmtsC3MACMIB.1.3.6.1.4.1.4115.1.4.3.6
95
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
95 total| Object Name |
|---|
cmtsC3MACMIBThis MIB manages the MAC software on the Cadant C3 CMTS. MODULE-IDENTITY .1.3.6.1.4.1.4115.1.4.3.6 |
dcxMACObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.4.3.6.1 |
dcxMACCmtsMacTableAdditional columns for docsIfCmtsMacTable.
An entry in this table exists for each ifEntry with an
ifType of docsCableMaclayer(127). SEQUENCE OF DcxMACCmtsMacEntry .1.3.6.1.4.1.4115.1.4.3.6.1.1 |
dcxMACCmtsMacEntrydcxMACCmtsMacEntry DcxMACCmtsMacEntry .1.3.6.1.4.1.4115.1.4.3.6.1.1.1 |
dcxMACCmtsMacModeIndicates the mode in which the MAC is operating. A read to this
value may return any of the modes defined by DocsisMacType. Only
the modes docsis, euroDocsis and mixed may be written.
When set to docsis or euroDocsis, all downstream and upstream
channels in this MAC domain will be configured in DOCSIS or
EuroDOCSIS mode respectively. When set to mixed, the downstream
channels will be configured in DOCSIS and the upstream channels
will be running in EuroDOCSIS mode.
The value custom will be returned in a read operation if any of
the underlying channels has been reconfigured in such a way that
the MAC can not be described a docsis, euroDocsis or mixed.rw DocsisMacType .1.3.6.1.4.1.4115.1.4.3.6.1.1.1.1 |
dcxMACCableAdvanceTypeCable Map Advance Type - 0 for Static, 1 for Dynamic.rw Enumeration .1.3.6.1.4.1.4115.1.4.3.6.1.1.1.2 |
dcxMACPlantLengthCable Plant Length (1-way) in kilometers.rw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.1.1.3 |
dcxMACFlapAgingTimeCable Flap List Aging Time in seconds.rw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.1.1.4 |
dcxMACFlapInsertTimeCable Flap List Insertion Time threshold in seconds.rw Unsigned32 ( 0..86400 ) UNITS "seconds" .1.3.6.1.4.1.4115.1.4.3.6.1.1.1.5 |
dcxMACFlapMissThreshCable Flap List Miss Threshold in misses.rw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.1.1.6 |
dcxMACFlapListSizeCable Flap List Maximum Number of Entries.rw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.1.1.8 |
dcxMACCmOfflineAgingTimeCable modem offline aging time in seconds. Minimum value
is 1 hour. Maximum time before aging a modem is 10 days.
Default value is 24 hours.rw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.1.1.9 |
dcxMACUccMaxFailedAttemptsMaximum number of consecutive failed channel change attempts that
a modem is allowed before the CMTS decides to no longer use the
modem for load balancing purposes.
If a modem successfully completes a channel change before the
maximum number of attempts is reached, the number of consecutive
failed attempts for the modem is reset.
A value of 0 indicates no limit.rw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.1.1.10 |
dcxMACDownstreamChannelTableAdditional columns for docsIfDownstreamChannelTable.
An entry in this table exists for each ifEntry with an
ifType of docsCableDownstream(128). SEQUENCE OF DcxMACDownstreamChannelEntry .1.3.6.1.4.1.4115.1.4.3.6.1.2 |
dcxMACDownstreamChannelEntrydcxMACDownstreamChannelEntry DcxMACDownstreamChannelEntry .1.3.6.1.4.1.4115.1.4.3.6.1.2.1 |
dcxMACDownChannelMacModeConfigures the downstream to DOCSIS or EuroDOCSIS.
When dcxMACDownChannelWirelessMode is disabled, changes to this
will impact the downstream annex type, modulation, symbol rate
and interleaver. When wireless mode is enabled, only the annex
type and interleaver will be changed.rw DocsisMacType .1.3.6.1.4.1.4115.1.4.3.6.1.2.1.1 |
dcxMACDownChannelUpconverterControls whether or not the internal upconverter is used.
If set to internal, the downstream IF frequency will operate
in read-only mode and will be configured internally by the
CMTS based on the downstream channel configuration.
If set to external, the IF frequency may be programmed to set the
frequency supplied to an external upconverter via the IF output.
In this mode, the downstream RF frequency and power will both
return 0 when read.rw Enumeration .1.3.6.1.4.1.4115.1.4.3.6.1.2.1.2 |
dcxMACDownChannelIfFrequencyThe IF frequency output by the modulator for this channel.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.2.1.3 |
dcxMACDownChannelWirelessModeEnabling this mode allows non-standard downstream modulations and
symbol rates to be configured which are suitable when using the
CMTS in a wireless application. Changes to dcxMACDownChannelMacMode
when wireless mode is active will only impact the downstream annex
type and interleaver settings. Modulation and symbol rates will
only be affected when wireless mode is disabled.
Disabling wireless mode will reset any non-standard modulation and
symbol rates settings in order to restore a standard DOCSIS or
EuroDOCSIS downstream.
If a set to active fails, a license may be required to activate the
feature.rw Enumeration .1.3.6.1.4.1.4115.1.4.3.6.1.2.1.4 |
dcxMACDownChannelSymbolRateSets the downstream symbol rate.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.2.1.5 |
dcxMACDownChannelAlphaThe percentage of excess bandwidth for the channel.ro Integer32 UNITS "percent" .1.3.6.1.4.1.4115.1.4.3.6.1.2.1.6 |
dcxMACUpstreamChannelTableAdditional columns for docsIfUpstreamChannelTable.
An entry in this table exists for each ifEntry with an
ifType of docsCableUpstream(129). SEQUENCE OF DcxMACUpstreamChannelEntry .1.3.6.1.4.1.4115.1.4.3.6.1.3 |
dcxMACUpstreamChannelEntrydcxMACUpstreamChannelEntry DcxMACUpstreamChannelEntry .1.3.6.1.4.1.4115.1.4.3.6.1.3.1 |
dcxMACUpChannelMacModeIndicates the mode in which this upstream is operating. A read or
write to this may consist only of the values docsis or euroDocsis.rw DocsisMacType .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.1 |
dcxMACUpChannelAmpAttenuationThe amplifier attenuation level for this logical
channel.rw TenthdBmV .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.2 |
dcxMACUpChannelIngressCancellationSets the ingress noise cancellation mode for this
logical channel. Not all modes may be valid for a
given logical channel configuration or hardware.rw Enumeration .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.3 |
dcxMACUpChannelGroupIdThe group ID for this logical channel used to associate it
with other upsteams on the same physical network. The group ID
is an index into the dcxMACUpstreamGroupTable which defines common
parameters for grouped upsteams. Upstreams do not have to be
grouped and there may be more than one group on the same physical
network. Spatially diverse upstreams should not have the same group ID.rw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.4 |
dcxMACUpChannelShortPollIntervalThe short interval for initial unicast maintanance on this logical
channel.rw TimeInterval .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.5 |
dcxMACUpChannelPeriodicPollIntervalThe periodic station maintanance interval on this logical channel.rw TimeInterval .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.6 |
dcxMACUpChannelInputPowerModeThe receiver input power mode for this logical channel. In fixed
mode the input power to the demodulator will remain fixed across
symbol rate changes. In automatic mode the demodulator may vary the
input power for optimal performance.rw Enumeration .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.7 |
dcxMACUpChannelPowerThe nominal receiver input power for this logical channel.rw TenthdBmV .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.8 |
dcxMACUpChannelPlantLengthThe cable length in km to the most distant CM on this logical
upstream.rw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.9 |
dcxMACUpChannelMaxCmMapProcTimeThe maximum time in microseconds allowed for modems on this logical
channel to process the Upstream Bandwidth Allocation MAP.rw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.10 |
dcxMACUpChannelConcatenationEnables or disables the use of packet concatenation by Cable Modems on
this logical channel.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.11 |
dcxMACUpChannelSpMgtTriggerIndexAn index into spectral management trigger table, identical
to dcxMACSpMgtTriggerIndex in that table. All entries with
the same value of dcxMACSpMgtTriggerIndex form a trigger group
all assigned to the same logical upstream channel or group.
Returns 0 if there are no triggers assigned to this logical
channel.rw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.12 |
dcxMACUpChannelLowPowerOffsetThe maximum power offset of a burst below the nominal
input power to the CMTS that will not cause a RNG-RSP
with status continue. Valid range is from -10 dBmV to
-1 dBmV in 1 dB increments.rw TenthdBmV (-100..-10) .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.13 |
dcxMACUpChannelHighPowerOffsetThe maximum power offset of a burst above the nominal
input power to the CMTS that will not cause a RNG-RSP
with status continue. Valid range is from +1 dBmV to
+10 dBmV in 1 dB increments.rw TenthdBmV .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.14 |
dcxMACUpChannelLogSnrAveTimeconstantThe averaging timeconstant used to calculate the per-logical channel
MIB variable docsIfSigQSignalNoise. The averaging uses a logarithmic
scale, so that the actual timeconstant used is 2^X, where X is the
value configured for this object. Increasing the value of X increases
the degree to which the SNR results are averaged over time, and reduces
the sensitivity of the reported channel SNR to local oscillations in
signal quality. Averaging can effectively be disabled by setting this
object to 0rw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.15 |
dcxMACUpChannelImpulseMitigationEnables or disables impulse noise mitigation for this
logical channel.rw Enumeration .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.16 |
dcxMACUpChannelRngPreambleGuardSymbolsNumber of guard symbols before the preamble pilot pattern for
ranging bursts. Guard symbols may help the receiver to mitigate
the effects of ISI and\or help with the detection of bursts with
an early arrival timerw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.17 |
dcxMACUpChannelNrngPreambleGuardSymbolsNumber of guard symbols before the preamble pilot pattern for
non-ranging bursts. Guard symbols may help the receiver to mitigate
the effects of ISI and\or help with the detection of bursts with
an early arrival timerw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.18 |
dcxMACUpChannelExtendedFrequencyErrorDetectOffsets in carrier frequency in the modem are corrected by the CMTS
during ranging. Typically most if not all off the frequency error is
removed in the initial ranging response with incremental changes removed
during periodic ranging. If large frequency offsets are expected during
initial or periodic ranging, this value may be configured to provide
extended frequency offset detection and correction.rw Enumeration .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.19 |
dcxMACUpChannelLogC3SnrTimeconstantThe averaging timeconstant used to calculate the per-logical channel
MIB variable dcxMACUpChannelSignalNoise. The averaging uses a logarithmic
scale, so that the actual timeconstant used is 2^X, where X is the
value configured for this object. Increasing the value of X increases
the degree to which the SNR results are averaged over time, and reduces
the sensitivity of the reported channel SNR to local oscillations in
signal quality. Averaging can effectively be disabled by setting this
object to 0rw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.20 |
dcxMACUpChannelSignalNoiseA measurement of the average signal/noise ratio for the logical upstream.
The averaging may be controlled using the dcxMACUpChannelLogC3SnrTimeconstant
variablero TenthdB UNITS "dB" .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.21 |
dcxMACUpChannelSafeConfigIf true, MIB SETs which would cause this logical channel to go offline will return
a failurerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.22 |
dcxMACUpChannelInitialRangingDelayThe number of extra microseconds to allow in a broadcast IUC3
grant to compensate for modems that perform initial ranging later
than expected.rw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.3.1.23 |
dcxMACUpstreamGroupTableEntries containing definitions for group IDs
that can be associated with an upstream channel. SEQUENCE OF DcxMACUpstreamGroupEntry .1.3.6.1.4.1.4115.1.4.3.6.1.4 |
dcxMACUpstreamGroupEntrydcxMACUpstreamGroupEntry DcxMACUpstreamGroupEntry .1.3.6.1.4.1.4115.1.4.3.6.1.4.1 |
dcxMACUpstreamGroupIdThe ID for this group. Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.4.1.1 |
dcxMACUpstreamGroupNameThe name associated with this grouprw OCTET STRING .1.3.6.1.4.1.4115.1.4.3.6.1.4.1.2 |
dcxMACUpstreamGroupLoadBalancingConfigures upstream load balancing for the group.
Options are: none, initialNumeric, periodic.
If set to none, no load balancing will be performed.
If set to initialNumeric, the CMTS may redirect modems to other active upstream
channels in the same group by setting the upstream channel ID override in the
RNG-RSP at any time up to the point where the modem successfully completes
periodic ranging. Once a modem has completed ranging it must be reset before it
may be moved to another upstream. The modems in a group will be distributed
evenly and numerically across the active channels in the group. When a modems
performs initial ranging, it will be sent to the upsteam with the least number
of active modems if the number of active modems on the current upsteam is greater
than the average number of modems per upsteam in the group. All channels are
treated equally when calculating loads.
If a modem fails to range on the desired channel following a ranging overide,
it will be allowed to remain on the channel on which it next performs initial
ranging.
If set to periodic, modems will be numerically distributed during initial ranging
and then selectively moved after registration using UCC. Periodic load balancing
will attempt to distribute the modems to maintain even bandwidth utilization across
the channels in a group.rw Enumeration .1.3.6.1.4.1.4115.1.4.3.6.1.4.1.3 |
dcxMACUpstreamGroupFrequencyIndexAn index into upstream frequency table, identical to
dcxMACUpstreamFrequencyIndex in that table. All entries
with the same value of dcxMACUpstreamFrequencyIndex form
a spectral frequency group all assigned to the same
upstream group. Returns 0 if there are no triggers assigned
to this group.rw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.4.1.4 |
dcxMACUpstreamGroupSpMgtTriggerIndexAn index into spectral management trigger table, identical
to dcxMACSpMgtTriggerIndex in that table. All entries with
the same value of dcxMACSpMgtTriggerIndex form a trigger group
all assigned to the same upstream group or channel. Returns 0 if
there are no triggers assigned to this group.rw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.4.1.5 |
dcxMACUpstreamGroupStatusUsed to create rows in this tablerw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4115.1.4.3.6.1.4.1.6 |
dcxMACUpstreamFrequencyTableDescribes the upstream spectrum available for use by one or more
upstream groups. Entries are grouped by dcxMACUpstreamFrequencyIndex,
with each group assigned to one or more upstream groups. SEQUENCE OF DcxMACUpstreamFrequencyEntry .1.3.6.1.4.1.4115.1.4.3.6.1.5 |
dcxMACUpstreamFrequencyEntryDescribes a single contiguous region of upstream spectrum, available for
use by one or more upstream spectral groups. DcxMACUpstreamFrequencyEntry .1.3.6.1.4.1.4115.1.4.3.6.1.5.1 |
dcxMACUpstreamFrequencyIndexAn index into the upstream frequency table representing
a group of spectral regions, all associated with the
same upstream spectral group. Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.5.1.1 |
dcxMACUpstreamFrequencyRegionAn index into the upstream frequency table which, when
grouped with other frequency regions with the same frequency
index fully describe the upstream frequency spectrum available
for use by a given spectral group. Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.5.1.2 |
dcxMACUpstreamFrequencyStartThe start frequency for this upstream spectral region.rw Integer32 UNITS "hertz" .1.3.6.1.4.1.4115.1.4.3.6.1.5.1.3 |
dcxMACUpstreamFrequencyStopThe stop frequency for this upstream spectral region.rw Integer32 UNITS "hertz" .1.3.6.1.4.1.4115.1.4.3.6.1.5.1.4 |
dcxMACUpstreamFrequencyStatusUsed to create entries in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4115.1.4.3.6.1.5.1.5 |
dcxMACSpectralMgtObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4115.1.4.3.6.1.6 |
dcxMACSpectralMgtTriggerTableDescribes the spectral management triggers assigned to one
or more upstream groups or channels. Entries are grouped by
dcxMACSpMgtTriggerIndex, with each group assigned to one or more
upstream channels or groups. SEQUENCE OF DcxMACSpectralMgtTriggerEntry .1.3.6.1.4.1.4115.1.4.3.6.1.6.1 |
dcxMACSpectralMgtTriggerEntryDescribes a single spectral management trigger, available for
use by one or more upstream channels or spectral groups. DcxMACSpectralMgtTriggerEntry .1.3.6.1.4.1.4115.1.4.3.6.1.6.1.1 |
dcxMACSpMgtTriggerIndexAn index into the spectral managment trigger table
representing a group of triggers, all assigned to
the same upstream channel or spectral group. Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.1.1.1 |
dcxMACSpMgtTriggerNumberAn index into the spectral managment trigger table which,
when grouped with other triggers with the same trigger
index fully describe the spectral mangement triggers
assigned to the same upstream channel or spectral group. Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.1.1.2 |
dcxMACSpMgtTriggerTypeIdentifies the trigger type represented by this entry.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.1.1.3 |
dcxMACSpMgtTriggerActionAn index into the spectral management action table,
identical to dcxMACSpMgtActionIndex in that table,
identifying the action to take if this trigger is
invoked. Returns 0 if there is no action associated
with this trigger.rw Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.1.1.4 |
dcxMACSpMgtTriggerParam1Parameter dependent on trigger type.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.1.1.5 |
dcxMACSpMgtTriggerParam2Parameter dependent on trigger type.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.1.1.6 |
dcxMACSpMgtTriggerParam3Parameter dependent on trigger type.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.1.1.7 |
dcxMACSpMgtTriggerParam4Parameter dependent on trigger type.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.1.1.8 |
dcxMACSpMgtTriggerParam5Parameter dependent on trigger type.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.1.1.9 |
dcxMACSpMgtTriggerParam6Parameter dependent on trigger type.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.1.1.10 |
dcxMACSpMgtTriggerParam7Parameter dependent on trigger type.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.1.1.11 |
dcxMACSpMgtTriggerParam8Parameter dependent on trigger type.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.1.1.12 |
dcxMACSpMgtTriggerStatusUsed to create and control the status of entries in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4115.1.4.3.6.1.6.1.1.13 |
dcxMACSpectralMgtActionTableDescribes the spectral management actions assigned to one
or more spectral managment triggers. SEQUENCE OF DcxMACSpectralMgtActionEntry .1.3.6.1.4.1.4115.1.4.3.6.1.6.2 |
dcxMACSpectralMgtActionEntryDescribes a single spectral management action, assigned to
one or more spectral management triggers. DcxMACSpectralMgtActionEntry .1.3.6.1.4.1.4115.1.4.3.6.1.6.2.1 |
dcxMACSpMgtActionIndexAn index into the spectral managment actions table
used to assign actions to spectral management triggers. Unsigned32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.2.1.1 |
dcxMACSpMgtActionTypeIdentifies the action type represented by this entry.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.2.1.2 |
dcxMACSpMgtActionParam1Parameter dependent on action type.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.2.1.3 |
dcxMACSpMgtActionParam2Parameter dependent on action type.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.2.1.4 |
dcxMACSpMgtActionParam3Parameter dependent on action type.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.2.1.5 |
dcxMACSpMgtActionParam4Parameter dependent on action type.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.2.1.6 |
dcxMACSpMgtActionParam5Parameter dependent on action type.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.2.1.7 |
dcxMACSpMgtActionParam6Parameter dependent on action type.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.2.1.8 |
dcxMACSpMgtActionParam7Parameter dependent on action type.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.2.1.9 |
dcxMACSpMgtActionParam8Parameter dependent on action type.rw Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.6.2.1.10 |
dcxMACSpMgtActionStatusUsed to create and control the status of entries in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4115.1.4.3.6.1.6.2.1.11 |
dcxMACSharedSecretTableSet up shared secrets for this DOCSIS MAC Interface SEQUENCE OF DcxMACSharedSecretEntry .1.3.6.1.4.1.4115.1.4.3.6.1.7 |
dcxMACSharedSecretEntrydcxMACSharedSecretEntry DcxMACSharedSecretEntry .1.3.6.1.4.1.4115.1.4.3.6.1.7.1 |
dcxMACSharedSecretIdID for the associated shared secret. Integer32 .1.3.6.1.4.1.4115.1.4.3.6.1.7.1.1 |
dcxMACSharedSecretStrThis is the shared secret itself, which is considered write-only. It can be SET
but when a GET operation is performed the value is not returned.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4115.1.4.3.6.1.7.1.2 |
dcxMACSharedSecretStatusRow status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4115.1.4.3.6.1.7.1.3 |