AP553LIU-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for AP553LIU-MIB.
74
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
74 total| Object Name |
|---|
liuAdmin OBJECT IDENTIFIER .1.3.6.1.4.1.498.22.1.3.1 |
RFC1155-SMI Unknown .1.3.6.1.4.1.498.22.1.3.1 |
ap553MIBversionIdentifies the version of the MIB as `X.YZT' where:
X: Major Revision (1-9)
Y: Minor Revision (0-9)
Z: Typographical Revision (0-9)
T: Test Revision (A-Z)
Upon formal release, the test revision will not be present.ro DisplayString .1.3.6.1.4.1.498.22.1.3.1.1 |
liuCsuNetCfg OBJECT IDENTIFIER .1.3.6.1.4.1.498.22.1.3.2 |
ap553NetSetFrameTypeDefines the line interface framing type as follows:
`esf' sets extended superframe format,
`d4' sets D4 framing format,
`auto' instructs the unit to determine framing
WEBFLAG
ESF
D4
Automatic
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.2.1 |
ap553NetOperFrameTypeIdentifies the line interface framing type acquired by the unit as
defined by the `ap553NetSetFrameType' object as follows:
`esf' indicates extended superframe format,
`d4' indicates D4 framing format,
`auto' indicates the unit is still `acquiring', frame type
is indeterminate at this time.
WEBFLAG
ESF
D4
Automatic
WEBENDro Enumeration .1.3.6.1.4.1.498.22.1.3.2.2 |
ap553NetEsfModeDefines the use of the Facilities Data Link as follows:
`ansi_T1_403' defines the FDL exchange per ANSI specification,
`tr-54016' defines the FDL exchange as ESF.
Selections of `ansi_T1_403' and `tr-54016' are only valid
when ap553NetOperFrameType is `esf'.
WEBFLAG
ANSI T1.403
TR-54016
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.2.3 |
ap553NetLineCodingDefines the Zero Code Suppression mechanism for the interface.
`b8zs' defines the use of a specified pattern of normal bits and
bipolar violations used to replace a sequence of eight zero bits.
`ami' (alternate mark inversion) defines a mode wherein no zero code
suppression is provided. Therefore ami line encoding does not protect
against inadequate ones density.
The DSU will enforce an 8x(N+1) minimum ones density requirement when
ap553NetLineCoding == `ami' and ap553DS0Fmt == `nx64k' and
ap553DS0AllocationScheme == `consecutive'.
WEBFLAG
B8ZS
AMI
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.2.4 |
ap553NetIntfTypeDefines the operating mode of the interface, and the attenuation or gain.
The following values specify operation as a standard DS1 interface, with
the specified attenuation:
`ds1-auto-lbo' allows the unit to determine the interface buildout value.
`ds1-zero-dB' sets the transmit buildout to 0.0 dB.
`ds1-neg7pt5-dB' sets the transmit buildout to -7.5dB.
`ds1-neg15pt0-dB' sets the transmit buildout to -15.0dB.
`ds1-neg22pt5-dB' sets the transmit buildout to -22.5dB.
The following values specify operation as a standard cross-connect DSX-1
interface, with the specified transmitter gain:
`dsx1-preeq133_ft'
`dsx1-preeq266_ft'
`dsx1-preeq399_ft'
`dsx1-preeq533_ft'
`dsx1-preeq655_ft'
WEBFLAG
DS1 Auto Line Buildout
DS1 0.0dB Line Buildout
DS1 -7.5dB Line Buildout
DS1 -15.0dB Line Buildout
DS1 -22.5dB Line Buildout
DSX1 0 - 133 ft Pre-equalization
DSX1 133 - 266 ft Pre-equalization
DSX1 266 - 399 ft Pre-equalization
DSX1 399 - 533 ft Pre-equalization
DSX1 533 - 655 ft Pre-equalization
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.2.5 |
ap553NetDS1IntfRcvLevelIdentifies the Network Interface Receive level for a DS1 type interface.
`noSignal' indicates that no T1 signal is detected on the interface, (the
`NS' LED on the unit's front panel will be on.
`pos2toNeg7pt5-dB'=> + 2.0dB to - 7.5dB DS1 interface receive level
`neg7pt5toNeg15-dB'=> - 7.5dB to -15.0dB DS1 interface receive level
`neg15toNeg22pt5-dB'=> -15.0dB to -22.5dB DS1 interface receive level
`lessThanNeg22pt5-dB'=> less than -22.5dB DS1 interface receive level
`invalidDSX1intf=> invalid object, interface type is DSX1
WEBFLAG
no signal
+ 2.0dB to - 7.5dB
- 7.5dB to -15.0dB
-15.0dB to -22.5dB
less than -22.5dB
invalid dsx selected
WEBENDro Enumeration .1.3.6.1.4.1.498.22.1.3.2.6 |
liuDsuCfg OBJECT IDENTIFIER .1.3.6.1.4.1.498.22.1.3.3 |
ap553DS0AllocationSchemeDefines the DSU DS0 allocation scheme.
`consecutive' specifies DSU data passed in contiguous DS0 cell assignments
as specified by the ap553StartingDS0 and ap553NumDS0s objects.
`alternate' specifies DSU data passed in every other DS0 cell, with each
data cell a corresponding adjacent cell is forced to marks (ones), this
scheme ensures that a minimum ones density requirement is met to maintain
frame synchronization. This scheme provides a maximum throughput
of 12x56K or 12x64K, as specified by the ap552DS0Format and
ap553NumDS0s objects.
The DSU will enforce an 8x(N+1) minimum ones density requirement when
ap553NetLineCoding == `ami' and ap553DS0Fmt == `nx64k' and
ap553DS0AllocationScheme == `consecutive'.
WEBFLAG
Consecutive
Alternate
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.3.1 |
ap553DS0FmtDefines the DS0 base rate as either 56K or 64K bits per second.
This object value, in conjunction with the ap553NumDS0s object
value determines the LIU aggregate bandwidth.
`nx64k' defines a DS0 data format as clear channel in which all 8 bits
of the DS0 are used for data.
`nx56k defines a DS0 data format as 7 bits for data, and 1 bit used for
signalling information or unused and forced to marks.
The DSU will enforce an 8x(N+1) minimum ones density requirement when
ap553NetLineCoding == `ami' and ap553DS0Fmt == `nx64k' and
ap553DS0AllocationScheme == `consecutive'.
WEBFLAG
N x 56K
N x 64K
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.3.2 |
ap553StartingDS0Defines the starting DS0 number for the bundle of DS0s used for the LIU
aggregate bandwidth.
Values of 1-24 are valid when ap553DS0AllocationScheme is consecutive.
Values of 1-23 are valid when ap553DS0AllocationScheme is alternate.rw INTEGER .1.3.6.1.4.1.498.22.1.3.3.3 |
ap553NumDS0sDefines the number of DS0 cells used for passing DSU data.
When ap553DS0AllocationScheme is consecutive, valid values are 1 - N
where N <= (25 - ap553StartingDS0).
When ap553DS0AllocationScheme is alternate, valid values are 1 - N
where N <= (25 - ap553StartingDS0)/2.rw INTEGER .1.3.6.1.4.1.498.22.1.3.3.4 |
ap553LIUAggregateRateDisplays the current aggregate LIU data rate as:
` aggRate Kbps ' with values ranging from ` 56 Kbps ' to ` 1536 Kbps ',
where aggregate rate is calculated as follows:
aggRate = ap553NumDS0s * (ap553DS0Fmt == `nx56k') ? 56 : 64;ro DisplayString .1.3.6.1.4.1.498.22.1.3.3.5 |
ap553SystemStatusThe System Status option. When enabled, allows the DSU to clamp DSR
upon receiving the following Network codes:
1. Out of Service Code (OOS)
2. Abnormal Station Code (ASC)
3. No Signal(not a network code)
4. other inactive channel codes (ICC)
WEBFLAG
Disable
Enable
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.3.6 |
ap553CircuitAssuranceThe Circuit Assurance option. When enabled, allows the DSU to clamp
CTS upon receiving the following Network codes:
1. IDLE(no DCD)
2. Out of Service Code (OOS)
3. Abnormal Station Code (ASC)
4. No Signal(not a network code)
5. other inactive channel codes (ICC)
WEBFLAG
Disable
Enable
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.3.7 |
ap553InbandLoopThe Inband Loop Control option. Defines the DSU response to Inband Line
Loopback codes as follows:
inhibit - the DSU does not respond to in-band T1 loop codes
payloadloop - the DSU starts or stops a payload loop test
lineloop - the DSU starts or stops a line loop test
WEBFLAG
Inhibit
Start/Stop Payload Loop
Start/Stop Line Loop
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.3.8 |
liuNetAlarmCfg OBJECT IDENTIFIER .1.3.6.1.4.1.498.22.1.3.4 |
ap553NetBpvTrapSeverityControls the reporting and defines the severity of the Network Bipolar
Violations Alarm when this event occurs and meets the window & threshold
requirements for reporting as specified by the associated window and
threshold object values below.
WEBFLAG
Inhibit
Critical
Major
Minor
Warning
Info
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.4.1 |
ap553NetBpvWindowSpecifies the sampling window in which to report the Network Bipolar
Violations alarm condition as active.
All other values specify the size of the sampling window in which the
event may be reported one time as active, as controlled by the associated
mask object value, when the associated obj's threshold condition is met.
WEBFLAG
One Minute
Fifteen Minutes
One Hour
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.4.2 |
ap553NetBpvThreshSpecifies the threshold of events to be exceeded for reporting the
Network Bipolar Violations alarm condition.
WEBFLAG
1
10
100
1,000
10,000
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.4.3 |
ap553NetCrcTrapSeverityControls the reporting and defines the severity of the Network Cyclical
Redundancy Check Alarm when this event occurs and meets the window and
threshold requirements for reporting as specified by the associated
window and threshold object values below.
WEBFLAG
Inhibit
Critical
Major
Minor
Warning
Info
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.4.4 |
ap553NetCrcWindowSpecifies the sampling window in which to report the Network Cyclical
Redundancy Check alarm condition as active.
All other values specify the size of the sampling window in which the
event may be reported one time as active, as controlled by the associated
mask object value, when the associated obj's threshold condition is met.
WEBFLAG
One Minute
Fifteen Minutes
One Hour
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.4.5 |
ap553NetCrcThreshSpecifies the threshold of events to be exceeded for reporting the
Network Cyclical Redundancy Check alarm condition.
WEBFLAG
1
10
100
1,000
10,000
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.4.6 |
ap553NetLadTrapSeverityControls the reporting and defines the severity of the Network Low
Average Density Alarm when this event occurs and meets the window and
threshold requirements for reporting as specified by the associated
window and threshold object values below.
WEBFLAG
Inhibit
Critical
Major
Minor
Warning
Info
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.4.7 |
ap553NetLadWindowSpecifies the sampling window in which to report the Network Low Average
Density alarm condition as active.
All other values specify the size of the sampling window in which the
event may be reported one time as active, as controlled by the associated
mask object value, when the associated obj's threshold condition is met.
WEBFLAG
One Minute
Fifteen Minutes
One Hour
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.4.8 |
ap553NetLadThreshSpecifies the threshold of events to be exceeded for reporting the
Network Low Average Density alarm condition.
WEBFLAG
1
10
100
1,000
10,000
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.4.9 |
ap553NetAisTrapSeverityControls the reporting and defines the severity of the Network Alarm
Indication Signal Alarm when this event occurs.
WEBFLAG
Inhibit
Critical
Major
Minor
Warning
Info
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.4.10 |
ap553NetLosTrapSeverityControls the reporting and defines the severity of the Network Loss of
Signal Alarm when this event occurs.
WEBFLAG
Inhibit
Critical
Major
Minor
Warning
Info
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.4.11 |
ap553NetOofTrapSeverityControls the reporting and defines the severity of the Network Out of
Frame Alarm when this event occurs.
WEBFLAG
Inhibit
Critical
Major
Minor
Warning
Info
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.4.12 |
ap553NetRcdYelTrapSeverityControls the reporting and defines the severity of the Network Received
Yellow Alarm when this event occurs.
WEBFLAG
Inhibit
Critical
Major
Minor
Warning
Info
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.4.13 |
ap553NetUssTrapSeverityControls the reporting and defines the severity of the Network
Unavailable Signal State Alarm when this event occurs.
WEBFLAG
Inhibit
Critical
Major
Minor
Warning
Info
WEBENDrw Enumeration .1.3.6.1.4.1.498.22.1.3.4.14 |
liuDiagnostics OBJECT IDENTIFIER .1.3.6.1.4.1.498.22.1.3.5 |
ap553DiagT1TestSpecifies the test to be executed, or stops the current test.rw Enumeration .1.3.6.1.4.1.498.22.1.3.5.1 |
ap553DiagTestDurationDefines the length of all LIU diagnostic tests.rw Enumeration .1.3.6.1.4.1.498.22.1.3.5.2 |
ap553DiagTestStatusDisplays the test in progress, if any.ro Enumeration .1.3.6.1.4.1.498.22.1.3.5.3 |
liuStatus OBJECT IDENTIFIER .1.3.6.1.4.1.498.22.1.3.6 |
ap553LedStatusA bitwise snapshot of the front panel LED states,
where 0 = LED off and 1 = LED on, as follows:
LED description
Octet 1 bit 7 - n/u
bit 6 - n/u
bit 5 - n/u
bit 4 - DCE LMI LMI traffic on DCE
bit 3 - SD NTWK send data - network traffic
bit 2 - RD NTWK receive data - network traffic
bit 1 - NS No Signal on T1 interface
bit 0 - OOF Out of Frame condition on T1 Interfacero OCTET STRING .1.3.6.1.4.1.498.22.1.3.6.1 |
ap553PortStatusA bitwise snapshot of interface port status conditions and EIA signals,
where 0 = condition not present, and 1 = condition present, as follows:
Octet 1 - NETWORK Interface Port Status
bit 7 - n/u
bit 6 - n/u
bit 5 - n/u
bit 4 - n/u
bit 3 - Alarm Indication Signal
bit 2 - Out Of Frame Alarm
bit 1 - Loss Of Signal Alarm
bit 0 - Remote Alarmro OCTET STRING .1.3.6.1.4.1.498.22.1.3.6.2 |
ap553PortFrameCountsThe total number of frames transmitted and received on each interface
port. This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.
Octet 1 - NETWORK Interface Transmit Frame Count Octet 2
bit 7 - 2^15 bit 7 - 2^7
bit 6 - 2^14 bit 6 - 2^6
bit 5 - 2^13 bit 5 - 2^5
bit 4 - 2^12 bit 4 - 2^4
bit 3 - 2^11 bit 3 - 2^3
bit 2 - 2^10 bit 2 - 2^2
bit 1 - 2^9 bit 1 - 2^1
bit 0 - 2^8 bit 0 - 2^0
Octet 3 - NETWORK Interface Receive Frame Count Octet 4
bit 7 - 2^15 bit 7 - 2^7
bit 6 - 2^14 bit 6 - 2^6
bit 5 - 2^13 bit 5 - 2^5
bit 4 - 2^12 bit 4 - 2^4
bit 3 - 2^11 bit 3 - 2^3
bit 2 - 2^10 bit 2 - 2^2
bit 1 - 2^9 bit 1 - 2^1
bit 0 - 2^8 bit 0 - 2^0ro OCTET STRING .1.3.6.1.4.1.498.22.1.3.6.3 |
liuCurrentStats OBJECT IDENTIFIER .1.3.6.1.4.1.498.22.1.3.7 |
ap553CurrentIntervalCompletionThe elapsed time into the current interval expressed as a percent of
completion from 0 to 100%. When the current Line Stats interval
is complete (15 minutes), the collected data is moved into the first
historical interval (#1), and collection begins again in this object.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.ro INTEGER .1.3.6.1.4.1.498.22.1.3.7.1 |
ap553CurrentErroredSecondsThe Line statistics for the current 15 minute interval, also specifies
the percent completion of this interval. When the current Line Stats
interval time is complete (15 minutes), this data is moved into the first
historical interval (#1), and collection begins again in this object.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.ro Gauge .1.3.6.1.4.1.498.22.1.3.7.2 |
ap553CurrentSeverelyErroredSecondsThe Line statistics for the current 15 minute interval, also specifies
the percent completion of this interval. When the current Line Stats
interval time is complete (15 minutes), this data is moved into the first
historical interval (#1), and collection begins again in this object.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.ro Gauge .1.3.6.1.4.1.498.22.1.3.7.3 |
ap553CurrentBurstyErroredSecondsThe Line statistics for the current 15 minute interval, also specifies
the percent completion of this interval. When the current Line Stats
interval time is complete (15 minutes), this data is moved into the first
historical interval (#1), and collection begins again in this object.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.
For a E1 product this statistic is Frame Alignment Signal Errorsro Gauge .1.3.6.1.4.1.498.22.1.3.7.4 |
ap553CurrentCrcErrorsThe Line statistics for the current 15 minute interval, also specifies
the percent completion of this interval. When the current Line Stats
interval time is complete (15 minutes), this data is moved into the first
historical interval (#1), and collection begins again in this object.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.
For a E1 product this statistic is CRC4ro Gauge .1.3.6.1.4.1.498.22.1.3.7.5 |
ap553CurrentUnavailableSecondsThe Line statistics for the current 15 minute interval, also specifies
the percent completion of this interval. When the current Line Stats
interval time is complete (15 minutes), this data is moved into the first
historical interval (#1), and collection begins again in this object.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.ro Gauge .1.3.6.1.4.1.498.22.1.3.7.6 |
ap553CurrentLossOfFrameErrorsThe Line statistics for the current 15 minute interval, also specifies
the percent completion of this interval. When the current Line Stats
interval time is complete (15 minutes), this data is moved into the first
historical interval (#1), and collection begins again in this object.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.
For a E1 product this statistic is Far End Block Errorsro Gauge .1.3.6.1.4.1.498.22.1.3.7.7 |
ap553CurrentBipolarViolationsErrorsThe Line statistics for the current 15 minute interval, also specifies
the percent completion of this interval. When the current Line Stats
interval time is complete (15 minutes), this data is moved into the first
historical interval (#1), and collection begins again in this object.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.
For a E1 product this statistic is LCVro Gauge .1.3.6.1.4.1.498.22.1.3.7.8 |
ap553CurrentLossOfSignalErrorsThe Line statistics for the current 15 minute interval, also specifies
the percent completion of this interval. When the current Line Stats
interval time is complete (15 minutes), this data is moved into the first
historical interval (#1), and collection begins again in this object.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.
For a E1 product this statistic is not usedro Gauge .1.3.6.1.4.1.498.22.1.3.7.9 |
liuTotalStats OBJECT IDENTIFIER .1.3.6.1.4.1.498.22.1.3.8 |
ap553TotalErroredSecondsThe line statistics totals of the valid Line Statistics Interval
objects as specified by the ap553ValidHistoryIntervals object value.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.ro Gauge .1.3.6.1.4.1.498.22.1.3.8.1 |
ap553TotalSeverelyErroredSecondsThe line statistics totals of the valid Line Statistics Interval
objects as specified by the ap553ValidHistoryIntervals object value.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.ro Gauge .1.3.6.1.4.1.498.22.1.3.8.2 |
ap553TotalBurstyErroredSecondsThe line statistics totals of the valid Line Statistics Interval
objects as specified by the ap553ValidHistoryIntervals object value.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.
For a E1 product this statistic is Frame Alignment Signal Errors.ro Gauge .1.3.6.1.4.1.498.22.1.3.8.3 |
ap553TotalCrcErrorsThe line statistics totals of the valid Line Statistics Interval
objects as specified by the ap553ValidHistoryIntervals object value.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.
For a E1 product this statistic is CRC4ro Gauge .1.3.6.1.4.1.498.22.1.3.8.4 |
ap553TotalUnavailableSecondsThe line statistics totals of the valid Line Statistics Interval
objects as specified by the ap553ValidHistoryIntervals object value.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.ro Gauge .1.3.6.1.4.1.498.22.1.3.8.5 |
ap553TotalLossOfFrameErrorsThe line statistics totals of the valid Line Statistics Interval
objects as specified by the ap553ValidHistoryIntervals object value.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.
For a E1 product this statistic is Far End Block Errorsro Gauge .1.3.6.1.4.1.498.22.1.3.8.6 |
ap553TotalBipolarViolationsErrorsThe line statistics totals of the valid Line Statistics Interval
objects as specified by the ap553ValidHistoryIntervals object value.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.
For a E1 product this statistic is LCVro Gauge .1.3.6.1.4.1.498.22.1.3.8.7 |
ap553TotalLossOfSignalErrorsThe line statistics totals of the valid Line Statistics Interval
objects as specified by the ap553ValidHistoryIntervals object value.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.
For a E1 product this statistic is not used.ro Gauge .1.3.6.1.4.1.498.22.1.3.8.8 |
liuHistoryStats OBJECT IDENTIFIER .1.3.6.1.4.1.498.22.1.3.9 |
ap553ValidHistoryIntervalsThe number of 15 minute intervals for which line statistics data has
been collected. The value will be 96 unless the interface was brought
on-line within the last 24 hours, in which case the value will be the
number of complete 15 minute intervals the interface has been online.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.ro INTEGER .1.3.6.1.4.1.498.22.1.3.9.1 |
ap553LineStats24hrHistoryTableThe ap553 Line Statistics 24 hour history table. This table is comprised
of 96 objects, each of which hold T1 Line statistics data for a 15 minute
time period. Upon power up or after a reset, data is collected in the
current interval object: ap553CurrentLineStats. After 15 minutes this
data is moved into the first of 96 historical objects. After each sub-
sequent 15 minute period completes, data is moved downstream, data from
interval #1 is moved into interval #2, etc. The number of valid history
intervals contained in ap553ValidLineStatsIntervals is incremented. The
ap553TotalLineStats object is recalculated after each 15 minute interval
completes, summing all valid interval data into this object. When all
96 objects have been filled, containing 24 hours of data, the oldest
object, #96, will be overwritten by object #95, at the completion of the
next 15 minute interval. In this fashion, the unit is able to maintain
a current 24 hour history of Line Statistics data. SEQUENCE OF Ap553HistoryEntry .1.3.6.1.4.1.498.22.1.3.9.2 |
ap553HistoryEntryAn entry in the Line Statistics 24 hour history table. Ap553HistoryEntry .1.3.6.1.4.1.498.22.1.3.9.2.1 |
ap553HistoryIntervalIdentifies the relative time period of this data. Interval #1 is the most
recent historical 15 minute period. Interval #96 is the oldest 15 minute
time period in the current 24 hour history.ro INTEGER .1.3.6.1.4.1.498.22.1.3.9.2.1.1 |
ap553ErroredSecondsDataThe Line Statistics Data for a 15 minute historical period
within the last 24 hours, as specified by the ap553HistoryInterval.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.ro Gauge .1.3.6.1.4.1.498.22.1.3.9.2.1.2 |
ap553SeverelyErroredSecondsDataThe Line Statistics Data for a 15 minute historical period
within the last 24 hours, as specified by the ap553HistoryInterval.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.ro Gauge .1.3.6.1.4.1.498.22.1.3.9.2.1.3 |
ap553BurstyErroredSecondsDataThe Line Statistics Data for a 15 minute historical period
within the last 24 hours, as specified by the ap553HistoryInterval.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.
For a E1 product this statistic is Frame Alignment Signal Errorsro Gauge .1.3.6.1.4.1.498.22.1.3.9.2.1.4 |
ap553CrcErrorsDataThe Line Statistics Data for a 15 minute historical period
within the last 24 hours, as specified by the ap553HistoryInterval.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.
For a E1 product this statistic is CRC4ro Gauge .1.3.6.1.4.1.498.22.1.3.9.2.1.5 |
ap553UnavailableSecondsDataThe Line Statistics Data for a 15 minute historical period
within the last 24 hours, as specified by the ap553HistoryInterval.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.ro Gauge .1.3.6.1.4.1.498.22.1.3.9.2.1.6 |
ap553LossOfFrameErrorsDataThe Line Statistics Data for a 15 minute historical period
within the last 24 hours, as specified by the ap553HistoryInterval.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.
For a E1 product this statistic is Far End Block Errorsro Gauge .1.3.6.1.4.1.498.22.1.3.9.2.1.7 |
ap553BipolarViolationsErrorsDataThe Line Statistics Data for a 15 minute historical period
within the last 24 hours, as specified by the ap553HistoryInterval.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.
For a E1 product this statistic is LCVro Gauge .1.3.6.1.4.1.498.22.1.3.9.2.1.8 |
ap553LossOfSignalErrorsDataThe Line Statistics Data for a 15 minute historical period
within the last 24 hours, as specified by the ap553HistoryInterval.
This object will be reset to zero after a read, and after power up,
soft reset, or factory defaults reset.
For a E1 product this statistic is not used.ro Gauge .1.3.6.1.4.1.498.22.1.3.9.2.1.9 |