GDCHDSL-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
195
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
195 total| Object Name |
|---|
gdc OBJECT IDENTIFIER .1.3.6.1.4.1.498 |
RFC1155-SMI Unknown .1.3.6.1.4.1.498 |
hdsl OBJECT IDENTIFIER .1.3.6.1.4.1.498.11 |
gdcHdslSystem OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.1 |
gdcHdslVersion OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.1.1 |
gdcHdslSystemMIBversionIdentifies the version of the MIB. The format of the version
is x.yzT, where 'x' identifies the major revision number, 'y'
identifies the minor revision number, 'z' identifies the
typographical revision, and T identifies the test revision.
Acceptable values for the individual revision components are
as follows:
x: 1 - 9
y: 0 - 9
z: 0 - 9
T: A - Z
Upon formal release, no designation for the test revision will
be present.ro Unknown .1.3.6.1.4.1.498.11.1.1.1 |
gdcHdslVersionTable SEQUENCE OF GdcHdslVersionEntry .1.3.6.1.4.1.498.11.1.1.2 |
gdcHdslVersionEntryAn entry in the GDC Hdsl Version Table. GdcHdslVersionEntry .1.3.6.1.4.1.498.11.1.1.2.1 |
gdcHdslVersionIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and sub-identifier.
The table describes the maintenance objects for
the unit and references the unit interface (cc = 00).ro SCinstance .1.3.6.1.4.1.498.11.1.1.2.1.1 |
gdcHdslFirmwareRevThe version number of the firmware, to allow products to know which
revision is installed. The released version number is sequenced from
, A-, ... AA, ... ZZ. Test versions are numerical from 01 to 99.ro DisplayString .1.3.6.1.4.1.498.11.1.1.2.1.2 |
gdcHdslModelNumberThis variable is used to determine the type
of card family installed ex.ro DisplayString .1.3.6.1.4.1.498.11.1.1.2.1.3 |
gdcHdslDownloadTableThe Hdsl download table SEQUENCE OF GdcHdslDownloadEntry .1.3.6.1.4.1.498.11.1.1.3 |
gdcHdslDownloadEntryAn entry in the GDC gdcHdslSystem Download Table. GdcHdslDownloadEntry .1.3.6.1.4.1.498.11.1.1.3.1 |
gdcHdslDownloadIndexInteger value which uniquely identifies the GDCHDSL to which this
entry is applicable. SCinstance is defined to be SLDi where:
S (byte value) - physical shelf slot location (01-32)
L (byte value) - line number (01)
D (byte value) - drop number (00-31)
i (byte value) - loop or interface number (00-03)ro SCinstance .1.3.6.1.4.1.498.11.1.1.3.1.1 |
gdcHdslActiveFirmwareRevThe version number of the firmware currently executing.
The format is MM.NN.BB where:
MM: Major Revision (0-99)
NN: Minor Revision (0-99)
BB: Bug Fix Revision (0-99)
Valid [i]nterface = 0ro DisplayString .1.3.6.1.4.1.498.11.1.1.3.1.2 |
gdcHdslStoredFirmwareRevThe version number of the firmware stored (in a compressed format)
but not currently executing.
MM: Major Revision (0-99)
NN: Minor Revision (0-99)
BB: Bug Fix Revision (0-99)
Valid [i]nterface = 0ro DisplayString .1.3.6.1.4.1.498.11.1.1.3.1.3 |
gdcHdslStoredFirmwareStatusThis object represents the state of the Non-Active or Stored firmware:
statBlank(1) Factory Default
statDownLoading(2) In process of downloading firmware
statOK(3) Zipped version checksum succesful (OK to switch)
(can set gdcHdslSwitchActiveFirmware to
switchActive(2))
statCheckSumBad(4) Failed checksum after download
statUnZipping(5) In process of uncompressing into active area
statBadUnZip(6) Failed last uncompress
statDownloadAborted(7) Download aborted by user
Valid [i]nterface = 0ro Enumeration .1.3.6.1.4.1.498.11.1.1.3.1.4 |
gdcHdslSwitchActiveFirmwareThis object is used to switch the active executing firmware from
the version in gdcHdslActiveFirmwareRev to the version in
gdcHdslStoredFirmwareRev.
When a switchActive(2) is set (write only) the element will:
1) reboot
2) uncompress stored code into active area
3) perform checksum on active area
4) Set gdcHdslStoredStatus object to indicate results
5) If succesfull:
update gdcHdslActiveFirmwareRev and gdcHdslStoredFirmwareRev
and begin executing
If failed:
replace active area with previous revision
The switchNorm(1) enumeration will always be read.
Setting switchActive(2) when the gdcHdslStoredFirmwareStatus is
not statOK(3) will result in an error.
Valid [i]nterface = 0rw Enumeration .1.3.6.1.4.1.498.11.1.1.3.1.5 |
gdcHdslDownloadingModeThis object is used to configure the download mode:
disableAll(1) Prevents any firmware downloading to GDCHDSL
enableAndWait(2) Allows downloading zipped code to be stored only!
enableAndSwitch(3) Allows downloading and then unzips and begins executing
the new code
Valid [i]nterface = 0rw Enumeration .1.3.6.1.4.1.498.11.1.1.3.1.6 |
gdcHdslEraseFlashA set of this object to erase(2) will erase the application
stored in flash. After setting this object, there should
be a delay of at least 2 minutes before downloading the
unit.rw Enumeration .1.3.6.1.4.1.498.11.1.1.3.1.7 |
gdcHdslMaintenance OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.1.2 |
gdcHdslMaintenanceTableThe table describes the maintenance objects for
the unit and references the unit interface (cc = 00). SEQUENCE OF GdcHdslMaintenanceEntry .1.3.6.1.4.1.498.11.1.2.1 |
gdcHdslMaintenanceEntryAn entry in the GDC HDSL Maintenance Configuration Table. GdcHdslMaintenanceEntry .1.3.6.1.4.1.498.11.1.2.1.1 |
gdcHdslMaintenanceLineIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and sub-identifier.
The table describes the maintenance objects for
the unit and references the unit interface (cc = 00).ro SCinstance .1.3.6.1.4.1.498.11.1.2.1.1.1 |
gdcHdslSoftResetSupports the action of soft resetting the unit. When this
object is set to reset(1), then the unit performs a soft
reset, whose meaning is specific to the type of unit being
managed. The value norm(2) can not be set by management.rw Enumeration .1.3.6.1.4.1.498.11.1.2.1.1.2 |
gdcHdslConfigModeThe hardware configuration mode of the unit. A unit may
be configured through hardware switches, jumper, straps, etc.
The value software(1) indicates that the unit is software
configurable. The value of hardware(2) indicates that some options
are hard configured and that software configuration is not
permitted of these options.ro Enumeration .1.3.6.1.4.1.498.11.1.2.1.1.3 |
gdcHdslSysUpTimeThis variable is used to report the elapsed system tick
time for conversion to real time at the controller and is
not related to the sysUpTime referenced in MIB-II.
Upon power-up of the unit, the elapsed time is cleared.
The elapsed time counter rolls over upon reaching the
maximum count.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.498.11.1.2.1.1.4 |
gdcHdslUnitTypeThis variable is used to define HDSL unit type.
When this object is set to ltu(1), the unit is a Line Terminating
Unit and serves as master. When this object is set to ntu(2), the unit
is a network terminating unit.rw Enumeration .1.3.6.1.4.1.498.11.1.2.1.1.5 |
gdcHdslDefaultInitThis is used to allow the NonVolatile Configuration to
be set to a factory default state. When this value is set to
factoryDefault(1) the unit will perform
a reset to make the default configuration take affect.
The value of normal(2) will be returned when the initialization
is complete.
The value normal(2) can not be set by management.rw Enumeration .1.3.6.1.4.1.498.11.1.2.1.1.6 |
gdcHdslDataTypeThis variable is used to define the HDSL data type. When this
object is set to data(2) the data pass through the unit is digital
data. When is set to voice(1) the data pass rhrough the unit is
voice data.rw Enumeration .1.3.6.1.4.1.498.11.1.2.1.1.7 |
gdcHdslLoopProvisionThis variable is used to define HDSL unit loop provision.
When this variable is set to pointopoint(1), the unit is connected
to another HDSL unit. When is set to pointomultipoint(2), the unit
is connected to more than one other HDSL units or data grooming.rw Enumeration .1.3.6.1.4.1.498.11.1.2.1.1.8 |
gdcHdslNumberofLoopsThis variable is used to define HDSL unit loop configuration.
It can be set for one to threee loops.rw Enumeration .1.3.6.1.4.1.498.11.1.2.1.1.9 |
gdcHdslFrontPanelThis variable is used to define the front Panel operation.rw Enumeration .1.3.6.1.4.1.498.11.1.2.1.1.10 |
gdcHdslRoutingConfigThis variable is used to define HDSL ......rw Enumeration .1.3.6.1.4.1.498.11.1.2.1.1.11 |
gdcHdslPrivateStorage1This variable is used for general purpose storage.rw DisplayString .1.3.6.1.4.1.498.11.1.2.1.1.12 |
gdcHdslPrivateStorage2This variable is used for general purpose storage.rw DisplayString .1.3.6.1.4.1.498.11.1.2.1.1.13 |
gdcHdslPrivateStorage3This variable is used for general purpose storage.rw DisplayString .1.3.6.1.4.1.498.11.1.2.1.1.14 |
gdcHdslLedStatusReturns a bitwise snapshot of the front panel LED state.
Octet 1 bit 7 - not used
bit 6 - not used
bit 5 - not used
bit 4 - not used
bit 3 - NORM E1
bit 2 - ES E1
bit 1 - AL
bit 0 - TM
Octet 2 bit 7 - not used
bit 6 - not used
bit 5 - NORM L3
bit 4 - ES L3
bit 3 - NORM L2
bit 2 - ES L2
bit 1 - NORM L1
bit 0 - ES L1ro OCTET STRING .1.3.6.1.4.1.498.11.1.2.1.1.15 |
fracExecutionFor Set, only execute is allowed.rw Enumeration .1.3.6.1.4.1.498.11.1.2.1.1.16 |
gdcHdslAlarmStatusThe current alarms of the unit without the alarm masks.ro OCTET STRING .1.3.6.1.4.1.498.11.1.2.1.1.17 |
gdcHdslV54ConfigThis object selects the ability of the unit to recognize
V.54 pattern. Only applicable to DC730 & DC731 units.rw Enumeration .1.3.6.1.4.1.498.11.1.2.1.1.18 |
gdcHdslFPRDLConfigThis object selects the pattern to be transmitted when
RDL test is selected via the front panel RDL switch.
Only applicable to DC730 & DC731 units.rw Enumeration .1.3.6.1.4.1.498.11.1.2.1.1.19 |
gdcHdslRLTimeOutThis object selects the RLTimeOut to be disabled(1)
or set to 10 minutes(2). Only applicable to SC710D2 units.rw Enumeration .1.3.6.1.4.1.498.11.1.2.1.1.20 |
gdcHdslRPEnableThis object selects the Remote power to be enabled(2)
or disabled(1). Only applicable RP products which are on the shelf.rw Enumeration .1.3.6.1.4.1.498.11.1.2.1.1.21 |
gdcHdslLedStatus1Returns a bitwise snapshot of the front panel LED state.
This mib object is only used for the new HDSl elements.
Octet 1 bit 7 - not used
bit 6 - EIA RD
bit 5 - EIA CO
bit 4 - EIA RS
bit 3 - NORM E1/T1 NORM
bit 2 - ES E1/T1 ER
bit 1 - AL
bit 0 - TM
Octet 2 bit 7 - not used
bit 6 - EIA SD
bit 5 - NORM L3
bit 4 - ES L3
bit 3 - NORM L2
bit 2 - ES L2
bit 1 - NORM L1
bit 0 - ES L1
Octet 3 bit 7 - not used
bit 6 - not used
bit 5 - ST (GT10xx, GT20xx)
bit 4 - RL (GT10xx, GT20xx)
bit 3 - LL (GT10xx, GT20xx)
bit 2 - INS (uas7722)
bit 1 - RPF FAULT
bit 0 - RPF NORMro OCTET STRING .1.3.6.1.4.1.498.11.1.2.1.1.22 |
gdcHdslConfiguration OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.1.3 |
gdcHdslE1ConfigTableThe GDC E1 Configuration table. Information in the entries
of this table are used to configure E1 interface. SEQUENCE OF GdcHdslE1ConfigEntry .1.3.6.1.4.1.498.11.1.3.1 |
gdcHdslE1ConfigEntryThe GDC E1 Configuration table entry. The information in
this entry augments are used to configure E1 interface. GdcHdslE1ConfigEntry .1.3.6.1.4.1.498.11.1.3.1.1 |
gdcHdslE1ConfigIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and sub-identifier.
In which this case is an E1 interface (cc=01).ro SCinstance .1.3.6.1.4.1.498.11.1.3.1.1.1 |
gdcHdslE1FramingModeThis variable is used to determine E1 framing mode.rw Enumeration .1.3.6.1.4.1.498.11.1.3.1.1.2 |
gdcHdslE1LineUnitThis variable is used to determine operating mode of the
HDSL system with respect to E1 trunk. When this variable
is set to tlu(1), the system operates as a termination line
unit. When this variable is set to ilu(2) the system operates
as an intermediate line unit.rw Enumeration .1.3.6.1.4.1.498.11.1.3.1.1.3 |
gdcHdslE1LineCodingThis variable describes the variety of Zero
Code Suppression used on the link, which in
turn affects a number of its characteristics.
E1 links, with or without CRC, use HDB3 or
AMI.
AMI refers to a mode wherein no zero code
suppression is present and the line encoding
does not solve the problem directly. In this
application, the higher layer must provide data
which meets or exceeds the pulse density re-
quirements, such as inverting HDLC data.rw Enumeration .1.3.6.1.4.1.498.11.1.3.1.1.4 |
gdcHdslDteConfigTableThe GDC DTE Configuration table. SEQUENCE OF GdcHdslDteConfigEntry .1.3.6.1.4.1.498.11.1.3.2 |
gdcHdslDteConfigEntryThe GDC DTE Configuration table entry. GdcHdslDteConfigEntry .1.3.6.1.4.1.498.11.1.3.2.1 |
gdcHdslDteConfigIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop.ro SCinstance .1.3.6.1.4.1.498.11.1.3.2.1.1 |
gdcHdslDteCtsModeThis variable controls the function of CTS.rw Enumeration .1.3.6.1.4.1.498.11.1.3.2.1.2 |
gdcHdslDteDataRateThis variable represents the DTE data Rate in 64K increments.rw INTEGER .1.3.6.1.4.1.498.11.1.3.2.1.3 |
gdcHdslDteTxClkSourceThe source of Tranmit Clock.
'ExternalTiming' indicates that recovered re-
ceive clock from another interface is used as
the transmit clock.
'InternalTiming' indicates that a local clock
source is used.
'loopTiming' indicates that the recovered re-
ceive clock is used as the transmit clock.rw Enumeration .1.3.6.1.4.1.498.11.1.3.2.1.4 |
gdcHdslT1ConfigTableThe GDC T1 Configuration table. Information in the entries
of this table are used to configure T1 interface. SEQUENCE OF GdcHdslT1ConfigEntry .1.3.6.1.4.1.498.11.1.3.3 |
gdcHdslT1ConfigEntryThe GDC T1 Configuration table entry. The information in
this entry augments are used to configure T1 interface. GdcHdslT1ConfigEntry .1.3.6.1.4.1.498.11.1.3.3.1 |
gdcHdslT1ConfigIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and sub-identifier.
In which this case is an T1 interface (cc=01).ro SCinstance .1.3.6.1.4.1.498.11.1.3.3.1.1 |
gdcHdslT1InterfaceTypeThis variable is used to set T1 Interface Typerw Enumeration .1.3.6.1.4.1.498.11.1.3.3.1.2 |
gdcHdslT1FramingModeThis variable is used to determine T1 framing mode.rw Enumeration .1.3.6.1.4.1.498.11.1.3.3.1.3 |
gdcHdslT1TxPreequalizationThis variable is used to set T1 Tx Line Preequalizationrw Enumeration .1.3.6.1.4.1.498.11.1.3.3.1.4 |
gdcHdslT1TxBulidOutThis variable is used to set T1 Tx Line Bulid Outrw Enumeration .1.3.6.1.4.1.498.11.1.3.3.1.5 |
gdcHdslT1InbandLBTypeThis variable is used to set T1 Inband LoopBack Type or Inhibit(1) this loopbackrw Enumeration .1.3.6.1.4.1.498.11.1.3.3.1.6 |
gdcHdslT1FDLModeThis variable is used to enable/disable T1 FDL Modero Enumeration .1.3.6.1.4.1.498.11.1.3.3.1.7 |
gdcHdslT1AISLoopdownTimeThis variable is used to set T1 AIS Loopdown Timerw Enumeration .1.3.6.1.4.1.498.11.1.3.3.1.8 |
gdcHdslT1LineCodingThis variable describes the variety of Zero
Code Suppression used on the link, which in
turn affects a number of its characteristics.
E1 links, with or without CRC, use HDB3 or
AMI.
AMI refers to a mode wherein no zero code
suppression is present and the line encoding
does not solve the problem directly. In this
application, the higher layer must provide data
which meets or exceeds the pulse density re-
quirements, such as inverting HDLC data.rw Enumeration .1.3.6.1.4.1.498.11.1.3.3.1.9 |
gdcHdslT1TxClkSourceThe source of Tranmit Clock.
'ExternalTiming' indicates that recovered re-
ceive clock from another interface is used as
the transmit clock.
'InternalTiming' indicates that a local clock
source is used.
'loopTiming' indicates that the recovered re-
ceive clock is used as the transmit clock.rw Enumeration .1.3.6.1.4.1.498.11.1.3.3.1.10 |
gdcHdslDiagnostics OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.1.4 |
gdcHdslDiagTableThe GDC HDSL Diagnostics table. SEQUENCE OF GdcHdslDiagEntry .1.3.6.1.4.1.498.11.1.4.1 |
gdcHdslDiagEntryThe GDC HDSL Diagnostics table entry. GdcHdslDiagEntry .1.3.6.1.4.1.498.11.1.4.1.1 |
gdcHdslDiagIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and sub-identifier,
which in this case is a network interface.ro SCinstance .1.3.6.1.4.1.498.11.1.4.1.1.1 |
gdcHdslLoopbackThis variable supports the action of a diagnostic loop
at the point indicated.
dataLoop & remoteLoop are only supported by uas7722rw Enumeration .1.3.6.1.4.1.498.11.1.4.1.1.2 |
gdcHdslBertTestThis variable supports the action of Bit error rate test. When
set to inhibit(1) no bert test is in process. When set to enable (2)
BERT is in processrw Enumeration .1.3.6.1.4.1.498.11.1.4.1.1.3 |
gdcHdslPerformance OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.1.5 |
gdcHdslCurrentTableThe GDC Hdsl Current Performance table. Information
in the entries of this table support the HDSL Scheduled
Performance Reports. SEQUENCE OF GdcHdslCurrentEntry .1.3.6.1.4.1.498.11.1.5.1 |
gdcHdslCurrentEntryAn entry in the Current table. GdcHdslCurrentEntry .1.3.6.1.4.1.498.11.1.5.1.1 |
gdcHdslCurrentIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and interface,
which in this case can be an E1 or Loop interface.ro SCinstance .1.3.6.1.4.1.498.11.1.5.1.1.1 |
gdcHdslCurrentESsThe number of Errored Seconds, encountered by
an E1 or Loop interface in the current 15 minute inter-
val.ro Gauge .1.3.6.1.4.1.498.11.1.5.1.1.2 |
gdcHdslCurrentSESsThe number of Severely Errored Seconds encoun-
tered by a Loop or E1 interface in the current 15
minute interval.ro Gauge .1.3.6.1.4.1.498.11.1.5.1.1.3 |
gdcHdslCurrentUASsThe number of Unavailable Seconds encountered
by a Loop or E1 interface in the current 15 minute in-
terval.ro Gauge .1.3.6.1.4.1.498.11.1.5.1.1.4 |
gdcHdslCurrentDMsThe number of Degraded Minutes (DMs) encoun-
tered by a Loop or E1 interface in the current 15
minute interval.ro Gauge .1.3.6.1.4.1.498.11.1.5.1.1.5 |
gdcHdslCurrentFEBEsThe number of Far End Block Errors encountered
by a Loop or E1 interface in the current 15
minute interval.ro Gauge .1.3.6.1.4.1.498.11.1.5.1.1.6 |
gdcHdslCurrentStatsThe number of Current ES, SES, UAS, DM and FEBE's
encountered by a Loop or E1 interface in the current 15
minute interval.ro OCTET STRING .1.3.6.1.4.1.498.11.1.5.1.1.7 |
gdcHdslIntervalTableThe Loop or E1 Interval table. SEQUENCE OF GdcHdslIntervalEntry .1.3.6.1.4.1.498.11.1.5.2 |
gdcHdslIntervalEntryAn entry in the Interval table. GdcHdslIntervalEntry .1.3.6.1.4.1.498.11.1.5.2.1 |
gdcHdslIntervalIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and interface,
which in this case is a Loop or E1 interface.ro SCinstance .1.3.6.1.4.1.498.11.1.5.2.1.1 |
gdcHdslIntervalNumberA number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes inter-
val (assuming that all 96 intervals are
valid).ro INTEGER .1.3.6.1.4.1.498.11.1.5.2.1.2 |
gdcHdslIntervalESsThe number of Errored Seconds encountered by a
Loop or E1 interface in one of the previous 96, indi-
vidual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.498.11.1.5.2.1.3 |
gdcHdslIntervalSESsThe number of Severely Errored Seconds encoun-
tered by a Loop or E1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.498.11.1.5.2.1.4 |
gdcHdslIntervalUASsThe number of Unavailable Seconds encountered
by a Loop or E1 interface in one of the previous 96,
individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.498.11.1.5.2.1.5 |
gdcHdslIntervalDMsThe number of Degraded Minutes (DMs) encoun-
tered by a Loop or E1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.498.11.1.5.2.1.6 |
gdcHdslIntervalFEBEsThis variable represents the HDSL loops Far end block errors.ro Gauge .1.3.6.1.4.1.498.11.1.5.2.1.7 |
gdcHdslIntervalStatsThis variable represents stats at the HDSL loops.ro OCTET STRING .1.3.6.1.4.1.498.11.1.5.2.1.8 |
gdcHdslTotalTableThe GDC HDSL Total Performance table. Information
in the entries of this table support the HDSL
Scheduled Performance Reports. 24 hour interval. SEQUENCE OF GdcHdslTotalEntry .1.3.6.1.4.1.498.11.1.5.3 |
gdcHdslTotalEntryAn entry in the Total table. GdcHdslTotalEntry .1.3.6.1.4.1.498.11.1.5.3.1 |
gdcHdslTotalIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and interface,
which in this case is a Loop or E1 interface.ro SCinstance .1.3.6.1.4.1.498.11.1.5.3.1.1 |
gdcHdslTotalESsThe number of Errored Seconds encountered by a
Loop or E1interface in the previous 24 hour intervalro Gauge .1.3.6.1.4.1.498.11.1.5.3.1.2 |
gdcHdslTotalSESsThe number of Severely Errored Seconds encoun-
tered by a Loop or E1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.498.11.1.5.3.1.3 |
gdcHdslTotalUASsThe number of Unavailable Seconds encountered
by a Loop or E1 interface in the previous 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.498.11.1.5.3.1.4 |
gdcHdslTotalDMsThe number of Degraded Minutes (DMs) encoun-
tered by a Loop or E1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.498.11.1.5.3.1.5 |
gdcHdslTotalFEBEsThe number of Far End Block Errors en-
countered by a Loop or E1 interface in the current 15
minute interval.ro Gauge .1.3.6.1.4.1.498.11.1.5.3.1.6 |
gdcHdslTotalStatsThe number of Total stats encountered by a Loop or E1
interface in the current 15 minute interval.ro OCTET STRING .1.3.6.1.4.1.498.11.1.5.3.1.7 |
gdcHdslIntervalMaintenanceTableThe GDC Loop/E1/T1 Interval table. SEQUENCE OF GdcHdslIntervalMaintenanceEntry .1.3.6.1.4.1.498.11.1.5.4 |
gdcHdslIntervalMaintenanceEntryThe GDC Loop/E1/T1 Interval table entry. GdcHdslIntervalMaintenanceEntry .1.3.6.1.4.1.498.11.1.5.4.1 |
gdcHdslIntervalMaintenanceIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and interface,
which in this case is a Loop or E1/T1 interface.ro SCinstance .1.3.6.1.4.1.498.11.1.5.4.1.1 |
gdcHdslResetIntervalsThis variable is used to reset Loop/E1/T1 performance intervals.
When it is set to reset, the Loop/E1/T1 performance tables are
reset to zero.rw Enumeration .1.3.6.1.4.1.498.11.1.5.4.1.2 |
gdcHdslNumberofValidIntervalsThis variable is used to read the number of intervals collected.
Each interval is an increment of 15 minutes.ro INTEGER .1.3.6.1.4.1.498.11.1.5.4.1.3 |
gdcHdslResetMajorAlarmThis variable is used to reset alarm per Loop basis.rw Enumeration .1.3.6.1.4.1.498.11.1.5.4.1.4 |
gdcHdslResetMinorAlarmThis variable is used to reset alarm per Loop basis.rw Enumeration .1.3.6.1.4.1.498.11.1.5.4.1.5 |
gdcHdslT1CurrentTableThe GDC Hdsl Current Performance table. Information
in the entries of this table support the HDSL Scheduled
Performance Reports. SEQUENCE OF GdcHdslT1CurrentEntry .1.3.6.1.4.1.498.11.1.5.5 |
gdcHdslT1CurrentEntryAn entry in the Current table. GdcHdslT1CurrentEntry .1.3.6.1.4.1.498.11.1.5.5.1 |
gdcHdslT1CurrentIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and interface,
which in this case can be an T1 interface.ro SCinstance .1.3.6.1.4.1.498.11.1.5.5.1.1 |
gdcHdslT1CurrentStatsThe number of Current ES, SES, UAS, BES,LOFC,CSS.
encountered by T1 interface in the current 15
minute interval.ro OCTET STRING .1.3.6.1.4.1.498.11.1.5.5.1.2 |
gdcHdslT1IntervalTableThe T1 Interval table. SEQUENCE OF GdcHdslT1IntervalEntry .1.3.6.1.4.1.498.11.1.5.6 |
gdcHdslT1IntervalEntryAn entry in the Interval table. GdcHdslT1IntervalEntry .1.3.6.1.4.1.498.11.1.5.6.1 |
gdcHdslT1IntervalIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and interface,
which in this case is T1 interface.ro SCinstance .1.3.6.1.4.1.498.11.1.5.6.1.1 |
gdcHdslT1IntervalNumberA number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes inter-
val (assuming that all 96 intervals are
valid).ro INTEGER .1.3.6.1.4.1.498.11.1.5.6.1.2 |
gdcHdslT1IntervalStatsThis variable represents stats(ES, SES, UAS, BES,LOFC,CSS.) for T1 interface.ro OCTET STRING .1.3.6.1.4.1.498.11.1.5.6.1.3 |
gdcHdslT1TotalTableThe GDC HDSL Total Performance table. Information
in the entries of this table support the HDSL
Scheduled Performance Reports. 24 hour interval. SEQUENCE OF GdcHdslT1TotalEntry .1.3.6.1.4.1.498.11.1.5.7 |
gdcHdslT1TotalEntryAn entry in the Total table. GdcHdslT1TotalEntry .1.3.6.1.4.1.498.11.1.5.7.1 |
gdcHdslT1TotalIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and interface,
which in this case is T1 interface.ro SCinstance .1.3.6.1.4.1.498.11.1.5.7.1.1 |
gdcHdslT1TotalStatsThe number of Total stats encountered by T1
interface in the current 15 minute interval.ro OCTET STRING .1.3.6.1.4.1.498.11.1.5.7.1.2 |
gdcHdslStatus OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.1.6 |
gdcHdslLoopStatusTableThe table describes the Status objects for
the loops and references the loop interfaces (cc = 02-04). SEQUENCE OF GdcHdslLoopStatusEntry .1.3.6.1.4.1.498.11.1.6.1 |
gdcHdslLoopStatusEntryAn entry in the GDC HDSL Status Configuration Table. GdcHdslLoopStatusEntry .1.3.6.1.4.1.498.11.1.6.1.1 |
gdcHdslLoopStatusLineIndexThis object identifies Status parameters associated
with the managed object.ro SCinstance .1.3.6.1.4.1.498.11.1.6.1.1.1 |
gdcHdslLoopStartUpSupports the action of initializing HDSL loop startup sequence.
When set to start(2), HDSL unit will reinitialize the start up sequence.
When set to cancel(3), the unit will abort the start up sequence.
When set to norm(1), the unit will operate normal.rw Enumeration .1.3.6.1.4.1.498.11.1.6.1.1.2 |
gdcHdslLoopTipRingReversalModeSignals the loop Tip and Ring status.
When norm(1), loop operates normal.
When reverse(2), loop Tip and Ring have been reversed.ro Enumeration .1.3.6.1.4.1.498.11.1.6.1.1.3 |
gdcHdslLoopSignaltoNoiseMarginRepresents the loop signal to noise margin in dB units.ro INTEGER ( 0..127 ) .1.3.6.1.4.1.498.11.1.6.1.1.4 |
gdcHdslLoopSNFracThis variable is used to be used with the
gdcHdslLoopSignaltoNoiseMargin variable if the following
manor:
a) Only the values 0 and 5 are allowed.
b) The value of zero means gdcHdslLoopSignaltoNoiseMargin
is a whole number.
c) The value of five means gdcHdslLoopSignaltoNoiseMargin
is a real number and that 0.5 must be added to it.ro INTEGER ( 0..5 ) .1.3.6.1.4.1.498.11.1.6.1.1.5 |
gdcHdslLoopSNAttenSenseThis variable identifies the sense of the
gdcHdslLoopSignaltoNoiseMargin variable.ro Enumeration .1.3.6.1.4.1.498.11.1.6.1.1.6 |
gdcHdslLoopPulseAttenRepresents twice the HDSL loop Pulse Attenuation level
in dB units.ro INTEGER ( 0..100) .1.3.6.1.4.1.498.11.1.6.1.1.7 |
gdcHdslLoopPulseAttenFracThis variable is used to be used with the
gdcHdslLoopPulseAtten variable if the following
manor:
a) Only the values 0 and 5 are allowed.
b) The value of zero means gdcHdslLoopPulseAtten
is a whole number.
c) The value of five means gdcHdslLoopPulseAtten
is a real number and that 0.5 must be added to it.ro INTEGER ( 0..5 ) .1.3.6.1.4.1.498.11.1.6.1.1.8 |
gdcHdslLoopGainRepresents the HDSL loop gain setting.ro Enumeration .1.3.6.1.4.1.498.11.1.6.1.1.9 |
gdcHdslLoopExchangeThis variable is used to represent the HDSL loop status.
When the value is returned to norm(1), HDSL loops are correctly
connected.
When the value is returned as exchange(2), the HDSl loop has been
interchange by error.ro Enumeration .1.3.6.1.4.1.498.11.1.6.1.1.10 |
gdcHdslDteStatusTableThe GDC DTE Status table. SEQUENCE OF GdcHdslDteStatusEntry .1.3.6.1.4.1.498.11.1.6.2 |
gdcHdslDteStatusEntryThe GDC DTE Configuration table entry. GdcHdslDteStatusEntry .1.3.6.1.4.1.498.11.1.6.2.1 |
gdcHdslDteStatusIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop.ro SCinstance .1.3.6.1.4.1.498.11.1.6.2.1.1 |
gdcHdslDteDTRstatusDTR EIA status indicatorro Enumeration .1.3.6.1.4.1.498.11.1.6.2.1.2 |
gdcHdslDteDCDstatusCO EIA status indicatorro Enumeration .1.3.6.1.4.1.498.11.1.6.2.1.3 |
gdcHdslDteRTSstatusRTS EIA indicatorro Enumeration .1.3.6.1.4.1.498.11.1.6.2.1.4 |
gdcHdslDteDSRstatusDSR EIA indicatorro Enumeration .1.3.6.1.4.1.498.11.1.6.2.1.5 |
gdcHdslDteStatusDte leads status
P1.7 not used
.6 EIA DCD
.5 EIA DTR
.4 EIA RTS
.3 EIA DSR
.2 not used
.1 not used
.0 not usedro OCTET STRING .1.3.6.1.4.1.498.11.1.6.2.1.6 |
gdcHdslDiagnosticResults OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.1.7 |
gdcHdslDiagResultsTableThe GDC HDSL Diagnostics table. SEQUENCE OF GdcHdslDiagResultsEntry .1.3.6.1.4.1.498.11.1.7.1 |
gdcHdslDiagResultsEntryThe GDC HDSL Diagnostics table entry. GdcHdslDiagResultsEntry .1.3.6.1.4.1.498.11.1.7.1.1 |
gdcHdslDiagResultsIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop, and sub-identifier,
which in this case is a network interface.ro SCinstance .1.3.6.1.4.1.498.11.1.7.1.1.1 |
gdcHdslTestExecutionStatusThe current execution status of the diagnostic test.
When set to inSync(1), BERT test is in sync and BER rate is valid.
When set to notInSync(2), BERT test is not in Sync and BER rate is
not valid.ro Enumeration .1.3.6.1.4.1.498.11.1.7.1.1.2 |
gdcHdslDiagResultErrThe results of the last diagnostic test. This can be the
current test running or the last completed test.
Note that the interpretation of these results may be affected
by the value of the gdcTestExecutionStatus object.ro INTEGER .1.3.6.1.4.1.498.11.1.7.1.1.3 |
gdcHdslDiagResultIntervalThis variable represents the Ber test intervals.
A time interval is defined as the time required for transmission
of a block of 2^24 bits.ro INTEGER .1.3.6.1.4.1.498.11.1.7.1.1.4 |
gdcHdslV54RDLTestThis variable indicates that the front panel RL button is selected
and transmitting a V54 pattern. Applicable only to DC730 units.ro Enumeration .1.3.6.1.4.1.498.11.1.7.1.1.5 |
gdcFractional OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.1.8 |
hdslFracTableThe DS1 Fractional table. SEQUENCE OF HdslFracEntry .1.3.6.1.4.1.498.11.1.8.1 |
hdslFracEntryAn entry in the DS1 Fractional table. HdslFracEntry .1.3.6.1.4.1.498.11.1.8.1.1 |
hdslFracIndexThe index value which uniquely identifies the interface to
which this entry is applicable. This has the form of a
SCinstance which defines the slot, line, drop.ro SCinstance .1.3.6.1.4.1.498.11.1.8.1.1.1 |
channelmappingThe object contains the channel mapping for multipoint. Time slot 0 is used
in all loops.
P1.8 f/u
P1.7 \
P1.6 \
P1.5 \
P1.4 \ This byte contains the starting time slot
P1.3 /
P1.2 /
P1.1 /
P1.0 /
P2.8 f/u
P2.7 \
P2.6 \
P2.5 \
P2.4 \ This byte contains the number of consecutive time slots
P2.3 /
P2.2 /
P2.1 /
P2.0 /rw INTEGER .1.3.6.1.4.1.498.11.1.8.1.1.2 |
gdcHdslHighwayObject to select the data highway for Loop n.rw Enumeration .1.3.6.1.4.1.498.11.1.8.1.1.3 |
gdcHdslTimeSlot16Object to select if Time Slot 16 is being used either to pass data,
or skipped from passing any data for Loop n.rw Enumeration .1.3.6.1.4.1.498.11.1.8.1.1.4 |
gdcHdslAlarmThresholds OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.1.9 |
hdslAlarmConfigTableThe hdslAlarmConfigTable contains entries that configure alarm
reporting. The structure of the table is such that alarm
configuration is supported on a unit and interface basis, and
then on an alarm type basis within the interface. For
simplicity sake alarms, be they unit or interface
related, are represented in one table. SEQUENCE OF HdslAlarmConfigEntry .1.3.6.1.4.1.498.11.1.9.1 |
hdslAlarmConfigEntryAn entry in the hdslAlarmConfigTable table. HdslAlarmConfigEntry .1.3.6.1.4.1.498.11.1.9.1.1 |
hdslAlarmConfigIndexThe index value which uniquely identifies the interface to
which this entry is applicable.ro SCinstance .1.3.6.1.4.1.498.11.1.9.1.1.1 |
hdslAlarmConfigIdentifierThe unique alarm identifier assigned to this alarm type.
The format of this identifier is an OBJECT IDENTIFIER that has
the following format: {iso(1) org(3) dod(6) internet(1)
private(4) enterprises(1) gdc(498) xxx(x) alarm(z) yyy(y)
where xxx(x) is the administratively assigned family object
identifier (z) is the object identifier for alarms in the family
defined MIB and yyy(y) is the administratively assigned alarm
type identifier for this alarm.ro OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.1.9.1.1.2 |
hdslAlarmThresholdThis function sets/reads the Major or Minor BER alarm threshold criteria.rw Enumeration .1.3.6.1.4.1.498.11.1.9.1.1.3 |
hdsl700G2 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.2 |
hdsl700G3 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.3 |
hdsl730D1 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.4 |
hdsl730D2 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.5 |
hdsl720G1 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.6 |
hdsl720G2 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.7 |
hdsl702G2 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.8 |
hdsl710D2 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.9 |
hdsl700G2RP OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.10 |
hdsl710D2RP OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.11 |
hdsl720G2RP OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.12 |
hdsl730D2RP OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.13 |
hdsl701T2 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.14 |
hdsl701T2RP OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.15 |
hdsl721T1 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.16 |
hdsl721T2 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.17 |
hdsl721T2RP OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.18 |
hdsl731D1 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.19 |
hdsl731D2 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.20 |
hdsl731D2RP OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.21 |
hdsl700AG2 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.22 |
hdsl700AG2NZ OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.23 |
hdslGT1030 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.25 |
hdslGT2030 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.26 |
uas7722 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.27 |
hdslGT1020 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.28 |
hdslGT2020 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.29 |
hdsl711D2 OBJECT IDENTIFIER .1.3.6.1.4.1.498.11.30 |