ADTRAN-DSUDPP-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for ADTRAN-DSUDPP-MIB.
104
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
104 total| Object Name |
|---|
adtran OBJECT IDENTIFIER .1.3.6.1.4.1.664 |
RFC1155-SMI Unknown .1.3.6.1.4.1.664 |
adProducts OBJECT IDENTIFIER .1.3.6.1.4.1.664.1 |
adDSUDP OBJECT IDENTIFIER .1.3.6.1.4.1.664.1.8 |
adDSUDPSelfTestPassThe DSUDP Self Diagnostics Passed. TRAP-TYPE .1.3.6.1.4.1.664.1.8.0.806 |
adDSUDPSelfTestFailThe DSUDP Self Diagnostics Failed TRAP-TYPE .1.3.6.1.4.1.664.1.8.0.807 |
adDSUDPNetworkINSThe network channel is In-Service. The OOS/OOF
condition has cleared. TRAP-TYPE .1.3.6.1.4.1.664.1.8.0.808 |
adDSUDPNetworkOOSThe network channel is in an Out-Of-Service state. TRAP-TYPE .1.3.6.1.4.1.664.1.8.0.809 |
adDSUDPdsuLoopbackClearThe DSU Loopback test condition cleared. TRAP-TYPE .1.3.6.1.4.1.664.1.8.0.810 |
adDSUDPdsuLoopbackThe DSU Loopback test is active. TRAP-TYPE .1.3.6.1.4.1.664.1.8.0.811 |
adDSUDPchannelLoopbackClearThe Channel Loopback test cleared. TRAP-TYPE .1.3.6.1.4.1.664.1.8.0.812 |
adDSUDPchannelLoopbackThe Channel Loopback test is active. TRAP-TYPE .1.3.6.1.4.1.664.1.8.0.813 |
adDSUDPocuLoopbackClearThe OCU Loopback test cleared. TRAP-TYPE .1.3.6.1.4.1.664.1.8.0.814 |
adDSUDPocuLoopbackThe OCU Loopback test is active. TRAP-TYPE .1.3.6.1.4.1.664.1.8.0.815 |
adDSUDPThrsAlertDailyUASThe Daily Un-Available Seconds UAS parameter has
reached or exceeds its threshold value. TRAP-TYPE .1.3.6.1.4.1.664.1.8.0.867 |
adDSUDPThrsAlertDailyAvailThe daily percent channel availability has reached or
dropped below its threshold value. TRAP-TYPE .1.3.6.1.4.1.664.1.8.0.875 |
adDSUDPThrsAlertIntUASThe Interval Un-Available Seconds (UAS) parameter has
reached or exceeds its threshold value. TRAP-TYPE .1.3.6.1.4.1.664.1.8.0.883 |
adMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.664.2 |
adDSUDPmg OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.8 |
adDSUDPprov OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.8.3 |
adDSUDPprovNet OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.8.3.1 |
adDSUDPnetLoopRateIndicates the DS0 loop data raterw Enumeration .1.3.6.1.4.1.664.2.8.3.1.1 |
adDSUDPnetTypeSelects the network typerw Enumeration .1.3.6.1.4.1.664.2.8.3.1.2 |
adDSUDPnetScramblerDisables/Enables Scramblingrw Enumeration .1.3.6.1.4.1.664.2.8.3.1.3 |
adDSUDPnetRemoteCfgEnables/Disables configuration by a remote DSUDPrw Enumeration .1.3.6.1.4.1.664.2.8.3.1.4 |
adDSUDPprovDte OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.8.3.2 |
adDSUDPdteRateSelects bit rate of primary DTErw Enumeration .1.3.6.1.4.1.664.2.8.3.2.1 |
adDSUDPdteFormatSelects DTE data formatrw Enumeration .1.3.6.1.4.1.664.2.8.3.2.2 |
adDSUDPdteWordLengthSelects DTE asynchronous word lengthrw Enumeration .1.3.6.1.4.1.664.2.8.3.2.3 |
adDSUDPdteInBandCommandSelects DTE in-band command typerw Enumeration .1.3.6.1.4.1.664.2.8.3.2.4 |
adDSUDPdteTxClockSelects transmit timing sourcerw Enumeration .1.3.6.1.4.1.664.2.8.3.2.5 |
adDSUDPdteCSOptionsConfigures CS signal lead on primary DTErw Enumeration .1.3.6.1.4.1.664.2.8.3.2.6 |
adDSUDPdteAntiStreamConfigures DTE Anti-Streaming Disconnectrw Enumeration .1.3.6.1.4.1.664.2.8.3.2.7 |
adDSUDPdteCDOptionsConfigures CD signal lead on primary DTErw Enumeration .1.3.6.1.4.1.664.2.8.3.2.8 |
adDSUDPdteTROptionsConfigures handling of TR lead from Primary DTErw Enumeration .1.3.6.1.4.1.664.2.8.3.2.9 |
adDSUDPdteSROptionsConfigures SR signal lead to primary DTErw Enumeration .1.3.6.1.4.1.664.2.8.3.2.10 |
adDSUDPdteRSCSDelayConfigures DTE signals RS-CS delayrw Enumeration .1.3.6.1.4.1.664.2.8.3.2.11 |
adDSUDPprovTest OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.8.3.3 |
adDSUDPtestTimeoutConfigures test timeout in secondsrw INTEGER .1.3.6.1.4.1.664.2.8.3.3.1 |
adDSUDPtestRdlCfgEnables/Disables response to Remote Digital Loopbackrw Enumeration .1.3.6.1.4.1.664.2.8.3.3.2 |
adDSUDPprovDial OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.8.3.4 |
adDSUDPDialStored1Edit or View stored Dial Location 1rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.8.3.4.1 |
adDSUDPDialStored2Edit or View stored Dial Location 2rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.8.3.4.2 |
adDSUDPDialStored3Edit or View stored Dial Location 3rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.8.3.4.3 |
adDSUDPDialStored4Edit or View stored Dial Location 4rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.8.3.4.4 |
adDSUDPDialStored5Edit or View stored Dial Location 5rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.8.3.4.5 |
adDSUDPDialStored6Edit or View stored Dial Location 6rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.8.3.4.6 |
adDSUDPDialStored7Edit or View stored Dial Location 7rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.8.3.4.7 |
adDSUDPDialStored8Edit or View stored Dial Location 8rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.8.3.4.8 |
adDSUDPDialStored9Edit or View stored Dial Location 9rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.8.3.4.9 |
adDSUDPDialStored10Edit or View stored Dial Location 10rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.8.3.4.10 |
adDSUDPAutoAnswerEnables/Disables automatic answer of incoming callsrw Enumeration .1.3.6.1.4.1.664.2.8.3.4.11 |
adDSUDPperform OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.8.4 |
adDSUDPds0IntervalTableThe DS0 Interval Table. SEQUENCE OF AdDSUDPds0IntervalEntry .1.3.6.1.4.1.664.2.8.4.2 |
adDSUDPds0IntervalEntryAn entry in the DS0 Interval Table. AdDSUDPds0IntervalEntry .1.3.6.1.4.1.664.2.8.4.2.1 |
adDSUDPds0IntervalIndexThe index value which uniquely identifies the
DS0 interface to which this entry is applicable.ro INTEGER .1.3.6.1.4.1.664.2.8.4.2.1.1 |
adDSUDPds0IntervalNumberA number between 1 and 97, where 1 is the current
accumulating 15 minute interval and 2-97 are
completed 15 minute intervals. 2 is the most recent
completed interval and 97 is the least recent completed
15 minute interval (assuming that all 97 intervals are
valid).ro INTEGER .1.3.6.1.4.1.664.2.8.4.2.1.2 |
adDSUDPds0IntervalUASsThe number of Unavailable Seconds encountered by a
DS0 interface in one of the 97, individual 15 minute,
intervals.ro Counter .1.3.6.1.4.1.664.2.8.4.2.1.3 |
adDSUDPds0DailyTableThe DS0 Daily table. SEQUENCE OF AdDSUDPds0DailyEntry .1.3.6.1.4.1.664.2.8.4.3 |
adDSUDPds0DailyEntryAn entry in the DS0 Daily table. AdDSUDPds0DailyEntry .1.3.6.1.4.1.664.2.8.4.3.1 |
adDSUDPds0DailyIndexThe index value which uniquely identifies the
DS0 interface to which this entry is applicable.ro INTEGER .1.3.6.1.4.1.664.2.8.4.3.1.1 |
adDSUDPds0DailyNumberA number between 1 and 7, where 1 is the current
accumulating Daily Interval and 2-7 are the completed
Daily Intervals. 2 is the most recent completed Daily
Interval and 7 is the least recent completed Daily
Interval (assuming that all 7 Daily Intervals are
valid).ro INTEGER .1.3.6.1.4.1.664.2.8.4.3.1.2 |
adDSUDPds0DailyUASsThe number of Unavailable Seconds encountered by
a DS0 interface in one of the 7 Daily Intervals.ro Counter .1.3.6.1.4.1.664.2.8.4.3.1.3 |
adDSUDPds0DailyAvailThe percentage (times 100) of channel availability
encountered by a DS0 interface in one of the 7 Daily
Intervals.ro INTEGER .1.3.6.1.4.1.664.2.8.4.3.1.4 |
adDSUDPds0DailyAvgAvailThe percentage (times 100) of channel availability
averaged over the last 7 daysro INTEGER .1.3.6.1.4.1.664.2.8.4.3.1.5 |
adDSUDPds0IntervalThrsTableThe DS0 Interval Threshold Table. SEQUENCE OF AdDSUDPds0IntervalThrsEntry .1.3.6.1.4.1.664.2.8.4.4 |
adDSUDPds0IntervalThrsEntryAn entry in the DS0 Threshold Table. AdDSUDPds0IntervalThrsEntry .1.3.6.1.4.1.664.2.8.4.4.1 |
adDSUDPds0IntervalThrsIndexThe index value which uniquely identifies the
DS0 interface to which this entry is applicable.ro INTEGER .1.3.6.1.4.1.664.2.8.4.4.1.1 |
adDSUDPds0IntervalThrsUASsThe DS0 performance monitor Threshold Value for the
15 minute Unavailable Seconds parameter. The default
value is 1, which equates to approximately 99.9%
Availability for a 15 minute Interval.rw INTEGER .1.3.6.1.4.1.664.2.8.4.4.1.2 |
adDSUDPds0DailyThrsTableThe DS0 Daily Threshold Table. SEQUENCE OF AdDSUDPds0DailyThrsEntry .1.3.6.1.4.1.664.2.8.4.5 |
adDSUDPds0DailyThrsEntryAn entry in the DS0 Threshold Table. AdDSUDPds0DailyThrsEntry .1.3.6.1.4.1.664.2.8.4.5.1 |
adDSUDPds0DailyThrsIndexThe index value which uniquely identifies the
DS0 interface to which this entry is applicable.ro INTEGER .1.3.6.1.4.1.664.2.8.4.5.1.1 |
adDSUDPds0DailyThrsUASsThe DS0 performance monitor Threshold Value for
the Daily Unavailable Seconds parameter. The
default value is 86, which equates to approximately
99.9% Availability for a Daily Interval.rw INTEGER .1.3.6.1.4.1.664.2.8.4.5.1.2 |
adDSUDPds0DailyThrsAvailThe DS0 performance monitor Threshold Value for
the percentage channel Availability parameter.
The default value is 9950 (% times 100), which equates
to 99.5% Availability for a Daily Interval.rw INTEGER .1.3.6.1.4.1.664.2.8.4.5.1.3 |
adDSUDPds0AlertTableThe DS0 Performance Monitor Alert Table SEQUENCE OF AdDSUDPds0AlertEntry .1.3.6.1.4.1.664.2.8.4.6 |
adDSUDPds0AlertEntryAn entry in the DS0 PM Alert Table AdDSUDPds0AlertEntry .1.3.6.1.4.1.664.2.8.4.6.1 |
adDSUDPds0AlertIndexThe index value which uniquely identifies the
DS0 PM interface to which this entry is applicable.ro INTEGER .1.3.6.1.4.1.664.2.8.4.6.1.1 |
adDSUDPds0AlertStatusThis bit map variable indicates Threshold Crossing
Events for DS0 performance monitored parameters.
When a parameter exceeds its threshold value, the
parameter's bit is set in this variable. A SNMP
trap is generated if the parameter's alert enable
bit is set.
The alert event bit values are:
1 Interval UAS
2 Daily UAS
4 Daily percent Availabilityro INTEGER .1.3.6.1.4.1.664.2.8.4.6.1.2 |
adDSUDPds0AlertEnableThis bit map variable enables changes in the DS0
PM Alert Status to generate a SNMP Trap.
The alert enable bit values are:
1 Interval UAS
2 Daily UAS
4 Daily percent Availabilityrw INTEGER .1.3.6.1.4.1.664.2.8.4.6.1.3 |
adDSUDPalarm OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.8.5 |
adDSUDPAlarmStatusThis bit map variable indicates changes in the DSUDP
status. When a status bit changes state, the
the corresponding bit is set in this variable.
The alarm event bit values are:
1 No Alarm
2 0
4 0
8 Self diagnostics failed
16 OOS/OOF from network
32 DSUDP Loopback
64 Channel Loopback
128 OCU Loopbackro INTEGER .1.3.6.1.4.1.664.2.8.5.1 |
adDSUDPAlarmMajorA bit mask to select items of the
AlarmStatus which represent a Major Alarmro INTEGER .1.3.6.1.4.1.664.2.8.5.2 |
adDSUDPAlarmMinorA bit mask to select items of the
AlarmStatus which represent a Minor Alarmro INTEGER .1.3.6.1.4.1.664.2.8.5.3 |
adDSUDPAlarmAlertA bit mask to select items of the
AlarmStatus which represent an Alert Alarmro INTEGER .1.3.6.1.4.1.664.2.8.5.4 |
adDSUDPAlarmInfoA bit mask to select items of the
AlarmStatus which represent an Info Alarmro INTEGER .1.3.6.1.4.1.664.2.8.5.5 |
adDSUDPAlarmEnableThis bit map variable enables changes in the DSUDP
Alarm Status to generate a SNMP Trap.
The alarm enable bit values are:
1 0
2 0
4 0
8 Self diagnostics failed
16 OOS/OOF from network
32 DSUDP Loopback
64 Channel Loopback
128 OCU Loopbackrw INTEGER .1.3.6.1.4.1.664.2.8.5.6 |
adDSUDPtest OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.8.6 |
adDSUDPTestCmdA SET performs the selected testrw Enumeration .1.3.6.1.4.1.664.2.8.6.1 |
adDSUDPTestStatusCurrent test statusro Enumeration .1.3.6.1.4.1.664.2.8.6.2 |
adDSUDPTestErrorsThis variable accumulates errors for the active test
pattern. A SET operation will clear the error count.rw INTEGER .1.3.6.1.4.1.664.2.8.6.3 |
adDSUDPTestRxPatternReceive test pattern statusro Enumeration .1.3.6.1.4.1.664.2.8.6.4 |
adDSUDPSelfDiagnosticsCurrent Self Test statusro Enumeration .1.3.6.1.4.1.664.2.8.6.5 |
adDSUDPTestTxPatternSETs default transmit test patternrw Enumeration .1.3.6.1.4.1.664.2.8.6.6 |
adDSUDPInjectErrorSET injects one error into active test patternrw INTEGER .1.3.6.1.4.1.664.2.8.6.7 |
adDSUDPstatus OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.8.7 |
adDSUDPStatusEIABit map status of Primay DTE EIA interface signals
(off = 0, on = 1), where bit positions are:
1 RI
2 RD
4 SD
8 CD
16 CS
32 RS
64 SR
128 TRro INTEGER .1.3.6.1.4.1.664.2.8.7.1 |
adDSUDPStatusConnectorThe jumper selected DTE interface connector on DSUDPro Enumeration .1.3.6.1.4.1.664.2.8.7.2 |
adDSUDPModeCurrent mode of DSUDPro Enumeration .1.3.6.1.4.1.664.2.8.7.3 |
adDSUDPLedStatusThis variable contains bit encoded values
for LED status (0=off, 1=on):
1 IDL
2 ALM
4 TST
8 ERRro INTEGER .1.3.6.1.4.1.664.2.8.7.4 |
adDSUDPcall OBJECT IDENTIFIER .1.3.6.1.4.1.664.2.8.8 |
adDSUDPDialStoredDials the stored number in register 1-10rw INTEGER .1.3.6.1.4.1.664.2.8.8.1 |
adDSUDPManualDialA SET dials the input command stringrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.664.2.8.8.2 |
adDSUDPAnswerCallA SET answers an incoming callrw INTEGER .1.3.6.1.4.1.664.2.8.8.3 |
adDSUDPHangUpA SET commands the DSUDP to go on-hookrw INTEGER .1.3.6.1.4.1.664.2.8.8.4 |