ZYXEL-LAG-MIB

AI MIB Summary

The ZYXEL-LAG-MIB enables monitoring and configuration of Link Aggregation Control Protocol (LACP) and static EtherChannel groups on Zyxel networking hardware, exposing critical metrics such as member port status, aggregation group operational state, and load-balancing parameters.

The subtree for link aggregation

Main OID:

zyxelLinkAggregation.1.3.6.1.4.1.890.1.15.3.42

Objects

Active

Status

Dependencies

Imported Objects

Objects

21 total

More MIBs from ZyXEL

Browse all ZyXELMIBs →

ZYXEL-IES5000-MIB

SNMP MIB module

3448 objects→

IES5206-MIB

The IES5206-MIB provides vendor-specific SNMP management capabilities for the IES5206, IES5212, and IES6217 industrial Ethernet switches, exposing proprietary objects for monitoring device health, interface statistics, and system configuration parameters. This private MIB extension enables granular visibility into hardware status, port-level metrics, and operational states specific to these Allied Telesis industrial networking platforms.

2259 objects→

ZYXEL-ves1724-56-MIB

SNMP MIB module

1842 objects→

ZYXEL-ves1608FE57-MIB

SNMP MIB module

1357 objects→

ZYXEL-XGS4700-48F-MIB

SNMP MIB module

1136 objects→

ZYXEL-MGS370012C-MIB

SNMP MIB module

1095 objects→

Object Name	Syntax	OID
zyxelLinkAggregationThe subtree for link aggregation MODULE-IDENTITY `.1.3.6.1.4.1.890.1.15.3.42`	MODULE-IDENTITY	`.1.3.6.1.4.1.890.1.15.3.42`
zyxelAggregationSetup OBJECT IDENTIFIER `.1.3.6.1.4.1.890.1.15.3.42.1`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.890.1.15.3.42.1`
zyAggregationStateEnable/Disable link aggregation control protocol.rw EnabledStatus (P-BRIDGE-MIB) `.1.3.6.1.4.1.890.1.15.3.42.1.1`	EnabledStatus (P-BRIDGE-MIB)	`.1.3.6.1.4.1.890.1.15.3.42.1.1`
zyAggregationSysPriorityThe system number is to set the priority of an active port using link aggregation control protocol. The smaller the number, the higher the priority level.rw INTEGER `.1.3.6.1.4.1.890.1.15.3.42.1.2`	INTEGER	`.1.3.6.1.4.1.890.1.15.3.42.1.2`
zyxelAggregationGroupTableThe table contains aggregation group configuration. SEQUENCE OF ZyxelAggregationGroupEntry `.1.3.6.1.4.1.890.1.15.3.42.1.3`	SEQUENCE OF ZyxelAggregationGroupEntry	`.1.3.6.1.4.1.890.1.15.3.42.1.3`
zyxelAggregationGroupEntryAn entry contains aggregation group configuration. ZyxelAggregationGroupEntry `.1.3.6.1.4.1.890.1.15.3.42.1.3.1`	ZyxelAggregationGroupEntry	`.1.3.6.1.4.1.890.1.15.3.42.1.3.1`
zyAggregationGroupIndexIndex of link aggregation group. INTEGER `.1.3.6.1.4.1.890.1.15.3.42.1.3.1.1`	INTEGER	`.1.3.6.1.4.1.890.1.15.3.42.1.3.1.1`
zyAggregationGroupStateEnable/Disable link aggregation control protocol on a special group.rw EnabledStatus (P-BRIDGE-MIB) `.1.3.6.1.4.1.890.1.15.3.42.1.3.1.2`	EnabledStatus (P-BRIDGE-MIB)	`.1.3.6.1.4.1.890.1.15.3.42.1.3.1.2`
zyAggregationGroupDynamicStateEnable/Disable dynamic link aggregation control protocol on a special group.rw EnabledStatus (P-BRIDGE-MIB) `.1.3.6.1.4.1.890.1.15.3.42.1.3.1.3`	EnabledStatus (P-BRIDGE-MIB)	`.1.3.6.1.4.1.890.1.15.3.42.1.3.1.3`
zyAggregationGroupCriteriaOutgoing traffic distribution type. Packets from the same source and/or to the same destination are sent over the same link within the trunk. By default, the switch uses the srcDstMac distribution type. If the switch is behind a router, the packet's destination or source MAC address will be changed. In this case, set the switch to distribute traffic based on its IP address to make sure port trunking can work properly.rw Enumeration `.1.3.6.1.4.1.890.1.15.3.42.1.3.1.4`	Enumeration	`.1.3.6.1.4.1.890.1.15.3.42.1.3.1.4`
zyxelAggregationPortTableThe table contains aggregation port configuration. SEQUENCE OF ZyxelAggregationPortEntry `.1.3.6.1.4.1.890.1.15.3.42.1.4`	SEQUENCE OF ZyxelAggregationPortEntry	`.1.3.6.1.4.1.890.1.15.3.42.1.4`
zyxelAggregationPortEntryAn entry contains aggregation port configuration. ZyxelAggregationPortEntry `.1.3.6.1.4.1.890.1.15.3.42.1.4.1`	ZyxelAggregationPortEntry	`.1.3.6.1.4.1.890.1.15.3.42.1.4.1`
zyAggregationPortGroupTrunk group which a port belongs.rw Enumeration `.1.3.6.1.4.1.890.1.15.3.42.1.4.1.1`	Enumeration	`.1.3.6.1.4.1.890.1.15.3.42.1.4.1.1`
zyAggregationPortDynamicStateTimeoutThis timeout is the time interval bEtween the individual port exchanges of LACP packets in order to check that the peer port in the trunk group is still up.rw INTEGER `.1.3.6.1.4.1.890.1.15.3.42.1.4.1.2`	INTEGER	`.1.3.6.1.4.1.890.1.15.3.42.1.4.1.2`
zyAggregationAutoLacpStateEnable/Disable Automatic link aggregation control protocol.rw EnabledStatus (P-BRIDGE-MIB) `.1.3.6.1.4.1.890.1.15.3.42.1.5`	EnabledStatus (P-BRIDGE-MIB)	`.1.3.6.1.4.1.890.1.15.3.42.1.5`
zyxelAggregationStatus OBJECT IDENTIFIER `.1.3.6.1.4.1.890.1.15.3.42.2`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.890.1.15.3.42.2`
zyAggregationAutoLacpTableThe table contains auto-lacp port configuration. SEQUENCE OF ZyAggregationAutoLacpEntry `.1.3.6.1.4.1.890.1.15.3.42.2.1`	SEQUENCE OF ZyAggregationAutoLacpEntry	`.1.3.6.1.4.1.890.1.15.3.42.2.1`
zyAggregationAutoLacpEntryAn entry contains auto-lacp port configuration. ZyAggregationAutoLacpEntry `.1.3.6.1.4.1.890.1.15.3.42.2.1.1`	ZyAggregationAutoLacpEntry	`.1.3.6.1.4.1.890.1.15.3.42.2.1.1`
zyAggregationAutoLacpTrunkGroupTrunk group which a port belongs.ro Enumeration `.1.3.6.1.4.1.890.1.15.3.42.2.1.1.1`	Enumeration	`.1.3.6.1.4.1.890.1.15.3.42.2.1.1.1`
zyAggregationAutoLacpRemoteChassisIdThis is the chassis id of the remote device.ro DisplayString (SNMPv2-TC) `.1.3.6.1.4.1.890.1.15.3.42.2.1.1.2`	DisplayString (SNMPv2-TC)	`.1.3.6.1.4.1.890.1.15.3.42.2.1.1.2`
zyAggregationAutoLacpRemotePortThis is the connected port of the remote device.ro INTEGER `.1.3.6.1.4.1.890.1.15.3.42.2.1.1.3`	INTEGER	`.1.3.6.1.4.1.890.1.15.3.42.2.1.1.3`