XLDV20PM-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
375
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
375 total| Object Name |
|---|
xldv20pmTrThresholdCrossingAlertThreshold crossing alert for PM on physical layer. TRAP-TYPE .1.3.6.1.4.1.231.7.1.2.1.1.4.10.0.200 |
xldv20pmTrAtmThresholdCrossingAlertThreshold crossing alert for PM on ATM layer . TRAP-TYPE .1.3.6.1.4.1.231.7.1.2.1.1.4.10.0.300 |
xldv20pmTrAtmObjectCreationAn Atm object is created. TRAP-TYPE .1.3.6.1.4.1.231.7.1.2.1.1.4.10.0.302 |
xldv20pmTrAtmObjectDeletionAn Atm object is deleted. TRAP-TYPE .1.3.6.1.4.1.231.7.1.2.1.1.4.10.0.303 |
xldv20pmTrAtmEndpointObjectCreationAn Atm endpoint object is created. TRAP-TYPE .1.3.6.1.4.1.231.7.1.2.1.1.4.10.0.304 |
xldv20pmTrAtmEndpointObjectDeletionAn Atm endpoint object is deleted. TRAP-TYPE .1.3.6.1.4.1.231.7.1.2.1.1.4.10.0.305 |
xldv20Pm OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.1.1.5 |
IMPORTS Unknown .1.3.6.1.4.1.231.7.1.2.1.1.5 |
xldv20pmPerformanceManagementControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.1.1.5.1 |
xldv20pmControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.1.1.5.1.1 |
xldv20pmCoIfIndexThis attribute provides the interface index of
the PM object for which PM parameters are
configured .rw Unsigned16 (XLDV20-MIB) .1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.1 |
xldv20pmCoNrHistEntriesSizeThis attribute is used to set the number of 15 minutes
history entries which should be stored for history
collection.
Default value is 1.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.2 |
xldv20pmCoIntervalTypeThis attribute identifies whether a 15 minutes interval
or a day interval is selected in case of a
resetIndividCurrent command.rw Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.3 |
xldv20pmCoControlReqThis attribute identifies a control command given by the
SNMP agent.
A reset for any individual PM object is possible via
command resetIndividCurrent.
The command setNrHistEntriesSize is used to set the
number of 15 minutes history entries for history
collection at a particular interface.rw Xldv20pmControlReq .1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.4 |
xldv20pmCoControlStatusThe status of a control request.ro Xldv20ControlStatus .1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.5 |
xldv20pmCoRemainingHistoryEntriesSizeThis attribute indicates the number of remaining history
entries which are available for the 15 minutes history
collection wthin the ONU.
PM on physical and ATM layer use the same history memory
which is limited in total to 2000 entries.
The manager can read this attribute after the execution
of the setNrHistEntriesSize command .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.6 |
xldv20pmCoOAMLevelThis attribute selects the OAM level
f1 (1), f2 (2), f3 (3) .rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.7 |
xldv20pmCoControlReqResultThe result of the last user command.ro Xldv20pmControlReq .1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.8 |
xldv20pmCoControlTimeStampThe time stamp of the last command (end of command).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.231.7.1.2.1.1.5.1.1.9 |
xldv20pmAtmControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.1.1.5.1.2 |
xldv20pmAcoIndexThis attribute provides the index of the AtmPm object
for which PM parameters shall be configured .rw Unsigned16 (XLDV20-MIB) .1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.1 |
xldv20pmAcoNrHistEntriesSizeThis attribute is used to set the number of 15 minutes
history entries which should be stored for history
collection.
The set HistEntrySize value is found in the
xldv20pmAcHistEntrySize.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.2 |
xldv20pmAcoIntervalTypeThis attribute identifies whether a 15 minutes interval
or a day interval is selected in case of a
resetIndividCurrent command.rw Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.3 |
xldv20pmAcoControlReqThis attribute identifies a control command given by the
SNMP agent.
A reset for any individual PM object is possible via
command resetIndividCurrent.
The command setNrHistEntriesSize is used to set the
number of 15 minutes history entries for history
collection at a particular interface.
The commands create/delete are used to create/delete
AtmPm monitoring objectes (entry in table
xldv20pmAtmObjectsTable).
The commands addEndpoint/deleteEndpoint are used to
add or delete AtmPm endpoints to/from an PMo monitoring
object.rw Xldv20pmControlReq .1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.4 |
xldv20pmAcoControlStatusThe status of a control request.ro Xldv20ControlStatus .1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.5 |
xldv20pmAcoRemainingHistoryEntriesSizeThis attribute indicates the number of remaining history
entries which are available for the 15 minutes history
collection within the ONU.
PM on physical and ATM layer use the same history memory
which is limited in total to 2000 entries.
Commonly used by PM on physical and ATM layer
The manager can read this attribute after the execution
of the setNrHistEntriesSize command .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.6 |
xldv20pmAcoFlowTypeThis attribute identifies the flow type :
F4 (VP) or F5 (VC) segment or endToEnd flow.rw Xldv20pmFlowType .1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.7 |
xldv20pmAcoFlowDirectionThe flow direction of OAM cells.
'inwards' means flow direction from outside (external interface)
to cross connection.
'outwards' means flow direction from inside to external interface.rw Xldv20FlowDirection .1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.8 |
xldv20pmAcoConnectionIndexThis attribute identifies the index of a
Vpl or Vcl cross connection.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.9 |
xldv20pmAcoConnectionIndexTypeThis attribute identifies the type of connection index
and the termination point. It is in case of
vplUni/vplNni : index of Vpl CC (xldv20AccVpiNniIndex)
vclUni/vplNni : index of Vcl CC (xldv20VcxIndex).rw Xldv20pmConnectionIndexType .1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.10 |
xldv20pmAcoRoleThe role of endpoint.
'analyseWithBackwardReporting' (sink) means extracting
forward monitoring (FM) OAM cells, sending back
backward reporting OAM cells and no data collection
for current and history table.
'analyseWithoutBackwardReporting' (sink) means extracting
FM cells without any other OAM handling
and also collecting data.
'generateWithCollect' (source) means inserting FM cells,
extracting backward reporting cells if they arrive
and collect data for current and history table.
'generateWithoutCollect' (source) means inserting FM cells
but without collecting data.
The CMU, the Ethernet part of the Twin NT s capable of
operating as inserting or extracting point.rw Xldv20pmRoleType .1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.12 |
xldv20pmAcoEndpointTypeIdentifies the type of endpoint.rw Xldv20pmEndpointType .1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.13 |
xldv20pmAcoControlReqResultThe result of the last user command.ro Xldv20pmControlReq .1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.14 |
xldv20pmAcoControlTimeStampThe time stamp of the last command (end of command).ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.231.7.1.2.1.1.5.1.2.15 |
xldv20pmPerformanceMonitoring OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.1.1.5.2 |
xldv20pmCommonCurrentTableThis table contains the entries for the current 15 minute interval
or the current day of PMo objects of the common group.
(adc, adr, e3n and e3f) . SEQUENCE OF Xldv20pmCommonCurrentEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2 |
xldv20pmCommonCurrentEntryAn entry describing the Common Current Data Table . Xldv20pmCommonCurrentEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1 |
xldv20pmCcIntervalTypeThis attribute is used to select between the
15 min or the day accumulation types.ro Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.1 |
xldv20pmCcOAMLevelThis attribute is used to select between the
3 OAM levels f1 (1), f2 (2) and f3 (3) .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.2 |
xldv20pmCcAdminStateThis read-write attribute is used to activate (unlock)
and deactivate (lock) the functions (incl. collection)
performed by this managed entity.
Note: the 15min collection object must be activated,
before day collection can operate.rw Xldv20AdminState .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.3 |
xldv20pmCcSuspectFlagThis read-only attribute will be set to indicate that
troubles arose during an interval and that the counter
values are suspect and incomplete.ro Xldv20pmSuspectType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.4 |
xldv20pmCcHistEntrySizeThe number of 15min history entries configured at the particular interface. This
attribute is used for history data collection.
The default value is 1 and means at least one history entry
is desired .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.5 |
xldv20pmCcNrHistEntriesAvailableThis read-only attribute indicates how many HistEntries
are already available.
The range of values is between 0 and xldv20pmCcHistEntrySize,
thereby 0 means that this entry is not valid .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.6 |
xldv20pmCcElapsedTimeThis read-only attribute represents the difference
between the current time and the start of the present
summary interval.
Units are seconds when 15 minute interval is selected
or minutes for day interval.
(Note: accurate to the sample time interval).ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.7 |
xldv20pmCcThresholdLimitIndexThis read-write attribute provides an index to the
ThresholdLimitTable managed entity that contains the
threshold limits for the performance parameters reported
by this managed entity.
When the value of this attribute is set to 1, default
threshold limits shall be used .rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.8 |
xldv20pmCcNeErroredSecondsA near end counter of Errored Seconds (ES)
over a 15 min/day interval.
Counter appearence depends on interface type and OAM
level :
- adc, e3n: valid for F3 level .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.9 |
xldv20pmCcFeErroredSecondsA far end counter of
Errored Seconds (ES) over a 15 min /day interval.
Counter appearence depends on interface type and OAM level :
- adr, e3f: valid for F3 level .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.10 |
xldv20pmCcNeSeverelyErroredSecondsRepresents a near end counter of
Severely Errored Seconds (SES) over a 15 min /day
interval.
Counter appearence depends on interface type and OAM level :
- adc, e3n: valid for F3 level .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.11 |
xldv20pmCcFeSeverelyErroredSecondsThis read-only attribute represents a far end counter of
Severely Errored Seconds (SES) over a 15 min /day
interval.
Counter appearence depends on interface type and OAM level :
- adr, e3f: valid for F3 level .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.12 |
xldv20pmCcNeBackgroundBlockErrorsThis read-only attribute represents a near end counter for
Background Block Errors (BBE) over a 15 min /day
interval.
Counter appearence depends on interface type and OAM
level :
- adc, e3n: valid for F3 level .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.13 |
xldv20pmCcFeBackgroundBlockErrorsThis read-only attribute represents a far end counter for
Background Block Errors (BBE) over a 15 min /day
interval.
Counter appearence depends on interface type and OAM
level :
- adr, e3f: valid for F3 level .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.14 |
xldv20pmCcNeUnavailableSecondsThis read-only attribute represents a counter of
Unavailable Seconds (UAS) within the current 15 minute interval
or current day.
Counter applicable for : adc, e3n and f3 level .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.15 |
xldv20pmCcFeUnavailableSecondsThis read-only attribute represents a far end counter of
Unavailable Seconds (UAS) within the current 15 minute interval
or current day.
Counter applicable for : adr, e3f and F3 level .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.2.1.16 |
xldv20pmCommonHistoryTableThis table contains the entries for the PMo objects of
the 15 min /one day-history data collection results at
the respective adc, adr drop area
interfaces . SEQUENCE OF Xldv20pmCommonHistoryEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.3 |
xldv20pmCommonHistoryEntryAn entry describing the Common History Data Table . Xldv20pmCommonHistoryEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1 |
xldv20pmChIntervalTypeThis type attribute is used to select between the
15 min or the day accumulation types.ro Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.1 |
xldv20pmChOAMLevelThis attribute is used to select between the
3 OAM levels f1 (1), f2 (2) and f3 (3) .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.2 |
xldv20pmChHistEntryNrThis attribute is an index used to address the PM history entry.
Entry 1 is the most recent, entry 96 is 24 hours ago.
The range of values is between 1 and xldv20pmCcHistEntrySize .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.3 |
xldv20pmChSuspectFlagWill be set to indicate that
troubles arose during an interval and that the counter
values are suspect and incomplete.ro Xldv20pmSuspectType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.4 |
xldv20pmChPeriodEndTimeDate/time at the end of the selected interval.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.5 |
xldv20pmChNeErroredSecondsThis read-only attribute represents a near end counter of Errored
Seconds (ES) over a 15 min /day interval.
Counter applicable for : adc, e3n and F3 level .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.6 |
xldv20pmChFeErroredSecondsThis read-only attribute represents a far end counter of Errored
Seconds (ES) within the current 15 minute interval or current day.
Counter applicable for : adr, e3f and F3 level .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.7 |
xldv20pmChNeSeverelyErroredSecondsThis read-only attribute represents a near end counter of
Severely Errored Seconds (SES) within the current 15 minute
interval or current day.
Counter applicable for : adc, e3n and F3 level .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.8 |
xldv20pmChFeSeverelyErroredSecondsThis read-only attribute represents a far end counter of
Severely Errored Seconds (SES) within the current 15 minute
interval or current day.
Counter applicable for : adr, e3f and F3 level .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.9 |
xldv20pmChNeBackgroundBlockErrorsThis read-only attribute represents a near end counter for
Background Block Errors (BBE) over a 15 min /day
interval.
Counter applicable for : adc, e3n and F3 level .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.10 |
xldv20pmChFeBackgroundBlockErrorsThis read-only attribute represents a far end counter for
Background Block Errors (BBE) over a 15 min /day
interval.
Counter applicable for : adr, e3n and F3 level .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.11 |
xldv20pmChNeUnavailableSecondsThis read-only attribute represents a near end counter of
Unavailable Seconds (UAS) for a 15 min /day interval.
Counter applicable for : adc, e3n and F3 level .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.12 |
xldv20pmChFeUnavailableSecondsThis read-only attribute represents a far end counter of
Unavailable Seconds (UAS) for a 15 min /day interval.
Counter applicable for : adr, e3f and F3 level .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.3.1.13 |
xldv20pmS3CurrentTableThis table contains the entries for the current 15 minute interval
or the current day for STS3c near-end and far-end PPTPs. SEQUENCE OF Xldv20pmS3CurrentEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4 |
xldv20pmS3CurrentEntryAn entry describing the STS3 near-end and far-end
Current Data Table . Xldv20pmS3CurrentEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1 |
xldv20pmS3cIntervalTypeThis type attribute is used to select between the
15 min or the day accumulation types.ro Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.1 |
xldv20pmS3cOAMLevelThis attribute is used to select between the
3 OAM levels f1 (1), f2 (2) and f3 (3) .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.2 |
xldv20pmS3cAdminStateThis read-write attribute is used to activate (unlock)
and deactivate (lock) the functions (incl. collection)
performed by this managed entity.
Note: the 15min collection object must be activated,
before day collection can operate.rw Xldv20AdminState .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.3 |
xldv20pmS3cSuspectFlagThis read-only attribute will be set to indicate that
troubles arose during an interval and that the counter
values are suspect and incomplete.ro Xldv20pmSuspectType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.4 |
xldv20pmS3cHistEntrySizeThis read-only attribute indicates the number of 15min
history entries configured at the particular interface.
The default value is 1 and means that at least one
history entry is provided .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.5 |
xldv20pmS3cNrHistEntriesAvailableThis read-only attribute indicates how many history entries
are already available.
The range of values is between 0 and xldv20S3cHistEntrySize,
thereby 0 means that this entry is not valid .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.6 |
xldv20pmS3cElapsedTimeThis read-only attribute represents the difference
between the current time and the start of the present
summary interval.
Units are seconds when 15 minute interval is selected
or minutes for day interval.
(Note: accurate to the sample time interval).ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.7 |
xldv20pmS3cThresholdLimitIndexThis read-write attribute provides an index to the
ThresholdLimitTable managed entity that contains the
threshold limits for the performance parameters reported
by this managed entity.
When the value of this attribute is set to 1, default
threshold limits shall be used
The range of values is [1,30].rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.8 |
xldv20pmS3cNeErroredSecondsThis read-only attribute represents a counter of Errored Seconds (ES)
within the current 15min interval or current day.
Counter applicable for : s3n and F1, F2, F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.9 |
xldv20pmS3cFeErroredSecondsThis read-only attribute represents a counter of
Errored Seconds (ES) within the current 15min interval or current day.
Counter applicable for : s3f and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.10 |
xldv20pmS3cNeSeverelyErroredSecondsThis read-only attribute represents a counter of
Severely Errored Seconds (SES) within the current
15min interval or current day.
Counter applicable for : s3n and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.11 |
xldv20pmS3cFeSeverelyErroredSecondsThis read-only attribute represents a counter of
Severely Errored Seconds (SES) within the current 15min interval
or current day.
Counter applicable for : s3f and for F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.12 |
xldv20pmS3cNeCodeViolationsThis read-only attribute represents a counter of
Code Violations Errors within the current 15min interval
or current day.
Counter applicable for : s3n and F1, F2, F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.13 |
xldv20pmS3cFeCodeViolationsThis read-only attribute represents a counter of
Code Violations Errors within the current 15min interval
or current day.
Counter applicable for : s3f and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.14 |
xldv20pmS3cNeUnavailableSecondsThis read-only attribute represents a counter of
Unavailable Seconds (UAS) within the current 15min interval
or current day.
Counter applicable for : s3n and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.15 |
xldv20pmS3cFeUnavailableSecondsThis read-only attribute represents a counter of
Unavailable Seconds (UAS) within the current 15min interval
or current day.
Counter applicable for : s3f and level F2 and F3 .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.16 |
xldv20pmS3cNeSeverelyErroredFrameSecondsThis read-only attribute represents a counter of
Severely Errored Frame Seconds within the current 15min interval
or current day.
Counter applicable for : s3n and F1 level only.ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.4.1.17 |
xldv20pmS3HistoryTableThis table contains the entries for the PMo history
objects at the near-end and far-end STS3c interfaces.
It contains results that are overtaken from the
s3CurrentTable PM-object at the end of a 15 min /day
interval . SEQUENCE OF Xldv20pmS3HistoryEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.5 |
xldv20pmS3HistoryEntryAn entry describing the STS3 near-end and far-end
History Data Table . Xldv20pmS3HistoryEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1 |
xldv20pmS3hIntervalTypeThis type attribute is used to select between the
15 min or the day accumulation types.ro Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.1 |
xldv20pmS3hOAMLevelThis attribute is used to select between the
3 OAM levels f1 (1), f2 (2) and f3 (3) .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.2 |
xldv20pmS3hHistEntryNrThis attribute is used as index to address the history entry.
Entry 1 is the most recent, entry 96 is 24 hours ago.
The range of values is between 1 and xldv20S3cHistEntrySize .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.3 |
xldv20pmS3hSuspectFlagThis read-only attribute will be set to indicate that
troubles arose during an interval and that the counter
values are suspect and incomplete.ro Xldv20pmSuspectType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.4 |
xldv20pmS3hPeriodEndTimeThis read-only attribute is a record of date/time at the
end of an interval .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.5 |
xldv20pmS3hNeErroredSecondsThis read-only attribute represents a set of history
counter for Errored Seconds (ES) for the passed up to 96
periods of 15 minutes and the passed day interval.
Counter applicable for : s3n and F1, F2, F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.6 |
xldv20pmS3hFeErroredSecondsThis read-only attribute represents a set of history
counter for Errored Seconds (ES) for the passed up to 96
periods of 15 minutes and the passed day interval.
Counter applicable for : s3f and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.7 |
xldv20pmS3hNeSeverelyErroredSecondsThis read-only attribute represents a set of history
counter for Severely Errored Seconds (SES) for the
passed up to 96 periods of 15 minutes and the passed day
interval.
Counter applicable for : s3n and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.8 |
xldv20pmS3hFeSeverelyErroredSecondsThis read-only attribute represents a set of history
counter for Severely Errored Seconds (SES) for the
passed up to 96 periods of 15 minutes and the passed day
interval.
Counter applicable for : s3f and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.9 |
xldv20pmS3hNeCodeViolationsThis read-only attribute represents a set of history
counter for Code Violations Errors for the passed up to
96 periods of 15 minutes and the passed day interval.
Counter applicable for : s3n and F1, F2, F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.10 |
xldv20pmS3hFeCodeViolationsThis read-only attribute represents a set of history
counter for Code Violations Errors for the passed up to
96 periods of 15 minutes and the passed day interval.
Counter applicable for : s3f and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.11 |
xldv20pmS3hNeUnavailableSecondsThis read-only attribute represents a set of history
counter for Unavailable Seconds (UAS) for the passed up
to 96 periods of 15 minutes and the passed day interval.
Counter applicable for : s3n and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.12 |
xldv20pmS3hFeUnavailableSecondsThis read-only attribute represents a set of history
counter for Unavailable Seconds (UAS) for the passed up
to 96 periods of 15 minutes and the passed day interval.
Counter applicable for : s3f and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.13 |
xldv20pmS3hNeSeverelyErroredFrameSecondsThis read-only attribute represents a set of history
counter for Severely Errored Frame Seconds for the
passed up to 96 periods of 15 minutes and the passed day
interval.
Counter applicable for : s3n and F1 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.5.1.14 |
xldv20pmD3CurrentTableThis table contains the entries for the current 15 minute interval
or the current day for DS3 near-end and far-end PPTPs.
Note: Day PM collection uses the 15min interval results . SEQUENCE OF Xldv20pmD3CurrentEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6 |
xldv20pmD3CurrentEntryAn entry describing the DS3 near-end and far-end Current
Data Table . Xldv20pmD3CurrentEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1 |
xldv20pmD3cIntervalTypeThis type attribute is used to select between the
15 min or the day accumulation types.ro Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.1 |
xldv20pmD3cOAMLevelThis attribute is used to select between the
3 OAM levels f1 (1), f2 (2) and f3 (3) .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.2 |
xldv20pmD3cAdminStateThis read-write attribute is used to activate (unlock)
and deactivate (lock) the functions (incl. collection)
performed by this managed entity.
Note: the 15min collection object must be activated,
before day collection can operate.rw Xldv20AdminState .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.3 |
xldv20pmD3cSuspectFlagThis read-only attribute will be set to indicate that
troubles arose during an interval and that the counter
values are suspect and incomplete.ro Xldv20pmSuspectType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.4 |
xldv20pmD3cHistEntrySizeThis read-only attribute indicates the configured history size.
The default value is 1 and means that at least one
history entry is provided.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.5 |
xldv20pmD3cNrHistEntriesAvailableThis read-only attribute indicates how many history entries
are already available.
The range of values is between 0 and xldv20pmD3cHistEntrySize,
thereby 0 means that this entry is not valid .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.6 |
xldv20pmD3cElapsedTimeThis read-only attribute represents the difference
between the current time and the start of the present
summary interval.
Units are seconds when 15 minute interval is selected
or minutes for day interval.
(Note: accurate to the sample time interval).ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.7 |
xldv20pmD3cThresholdLimitIndexThis read-write attribute provides an index to the
ThresholdLimitTable managed entity that contains the
threshold limits for the performance parameters reported
by this managed entity.
When the value of this attribute is set to 1, default
threshold limits shall be used. These default values are
not part of the threshold limit table but are hard coded
in the application SW of PM.
The range of values is [1,30].rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.8 |
xldv20pmD3cNeErroredSecondsCPThis read-only attribute represents a counter of Errored
Seconds (ES) within the current interval or current day,
the generation thereof is based on CP-bit parity.
Counter applicable for : d3n and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.9 |
xldv20pmD3cFeErroredSecondsCPThis read-only attribute represents a counter of Errored
Seconds (ES) within the current 15 minute interval or current day,
the generation thereof is based on CP-bit parity .
Counter applicable for : d3f and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.10 |
xldv20pmD3cNeErroredSecondsPLCPThis read-only attribute represents a counter of Errored
Seconds on PLCP-bit parity within the current 15 minute
interval or current day.
Counter applicable for : d3n and F3 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.11 |
xldv20pmD3cFeErroredSecondsPLCPThis read-only attribute represents a counter of Errored
Seconds on PLCP-bit parity within the current 15 minute
interval or current day.
Counter applicable for : d3f and F3 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.12 |
xldv20pmD3cNeSeverelyErroredSecondsCPThis read-only attribute represents a counter of
Severely Errored Seconds (SES) within the current 15 minute
interval or current day based on CP-bit parity, the generation thereof
is based on CP-bit parity.
Counter applicable for : d3n and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.13 |
xldv20pmD3cFeSeverelyErroredSecondsCPThis read-only attribute represents a counter of
Severely Errored Seconds (SES) within the current 15 minute
interval or current day, the generation thereof
is based on CP-bit parity .
Counter applicable for : d3f and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.14 |
xldv20pmD3cNeSeverelyErroredSecondsPLCPThis read-only attribute represents a counter of
Severely Errored Seconds (SES) within the current 15 minute
interval or current day, the generation thereof
is based on PLCP-bit parity .
Counter applicable for : d3n and F3 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.15 |
xldv20pmD3cFeSeverelyErroredSecondsPLCPThis read-only attribute represents a counter of
Severely Errored Seconds (SES) within the current 15 minute
interval or current day, the generation thereof
is based on PLCP-bit parity .
Counter applicable for : d3f and F3 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.16 |
xldv20pmD3cNeCodeViolationsPThis read-only attribute represents a counter of
Code Violations Errors (Count of P-bit parity errors)
within the current 15 minute interval or current day.
Counter applicable for : d3n and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.17 |
xldv20pmD3cNeCodeViolationsCPThis read-only attribute represents a counter of
Code Violations Errors (Count of CP-bit parity errors)
within the current 15 minute interval or current day.
Counter applicable for : d3n and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.18 |
xldv20pmD3cFeCodeViolationsCPThis read-only attribute represents a counter of
Code Violations Errors (Count of CP-bit parity errors)
within the current 15 minute interval or current day.
Counter applicable for : d3f and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.19 |
xldv20pmD3cNeCodeViolationsPLCPThis read-only attribute represents a counter of
Code Violations Errors (Count of PLCP frame Bit
Interleaved Parity errors) within the current 15 minute
interval or current day.
Counter applicable for : d3n and F3 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.20 |
xldv20pmD3cFeCodeViolationsPLCPThis read-only attribute represents a counter of
Code Violations Errors (Count of PLCP frame Bit
Interleaved Parity errors) within the current 15 minute
interval or current day.
Counter applicable for : d3f and F3 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.21 |
xldv20pmD3cNeUnavailableSecondsThis read-only attribute represents a counter of
Unavailable Seconds (UAS) within the current 15 minute
interval or current day.
Counter applicable for : d3n and F2 level only.ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.22 |
xldv20pmD3cFeUnavailableSecondsThis read-only attribute represents a counter of
Unavailable Seconds (UAS) within the current 15 minute
interval or current day.
Counter applicable for : d3f and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.23 |
xldv20pmD3cNeUnavailableSecondsPLCPThis read-only attribute represents a counter of
Unavailable Seconds (UAS) within the current 15 minute
interval or current day. The generation is based on PLCP-bit parity.
Counter applicable for : d3n and F3 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.24 |
xldv20pmD3cFeUnavailableSecondsPLCPThis read-only attribute represents a counter of
Unavailable Seconds (UAS) within the current 15 minute
interval or current day. The generation is based on PLCP-bit parity.
Counter applicable for : d3f and F3 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.25 |
xldv20pmD3cNeSasThis read-only attribute represents a counter of one
second intervals containing one ore more Severely
Errored Frame (SEF) defects or one or more Alarm
Indication Signal (AIS) defects within the current 15 minute
interval or current day.
Counter applicable for : d3n and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.26 |
xldv20pmD3cFeSasThis read-only attribute represents a counter of one
second intervals containing one ore more Severely
Errored Frame (SEF) defects or one or more Alarm
Indication Signal (AIS) defects within the current 15 minute
interval or current day.
Counter applicable for : d3f and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.6.1.27 |
xldv20pmD3HistoryTableThis table contains the entries for the PMo history
objects at the near-end and far-end DS3 interfaces.
It contains results that are overtaken from the
D3CurrentTable PM-object at the end of a 15 min /day
interval . SEQUENCE OF Xldv20pmD3HistoryEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7 |
xldv20pmD3HistoryEntryAn entry describing the DS3 near-end and far-end History
Data Table . Xldv20pmD3HistoryEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1 |
xldv20pmD3hIntervalTypeThis type attribute is used to select between the
15 min or the day accumulation types.ro Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.1 |
xldv20pmD3hOAMLevelThis attribute is used to select between the
3 OAM levels f1 (1), f2 (2) and f3 (3) .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.2 |
xldv20pmD3hHistEntryNrThis attribute is used as index to address a history entry.
Entry 1 is the most recent, entry 96 is 24 hours ago.
The range of values is between 1 and xldv20pmD3cHistEntrySize .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.3 |
xldv20pmD3hSuspectFlagThis read-only attribute will be set to indicate that
troubles arose during an interval and that the counter
values are suspect and incomplete.ro Xldv20pmSuspectType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.4 |
xldv20pmD3hPeriodEndTimeThis read-only attribute is a record of date/time at the
end of an interval .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.5 |
xldv20pmD3hNeErroredSecondsCPThis read-only attribute represents a set of history
counter of Errored Seconds (ES), the generation thereof
is based on CP-bit parity for a 15min /day interval.
Counter applicable for : d3n and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.6 |
xldv20pmD3hFeErroredSecondsCPThis read-only attribute represents a set of history
counter of Errored Seconds (ES), the generation thereof
is based on CP-bit parity for a 15min /day interval.
Counter applicable for : d3f and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.7 |
xldv20pmD3hNeErroredSecondsPLCPThis read-only attribute represents a set of history
counter of Errored Seconds (ES) (One second interval in
which Code Violations errors occure) for a 15min /day
interval.
Counter applicable for : d3n and F3 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.8 |
xldv20pmD3hFeErroredSecondsPLCPThis read-only attribute represents a set of history
counter of Errored Seconds (ES) (One second interval in
which Code Violations errors occure) for a 15min /day
interval.
Counter applicable for : d3f and F3 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.9 |
xldv20pmD3hNeSeverelyErroredSecondsCPThis read-only attribute represents a set of history
counter of Severely Errored Seconds (ES), the generation
thereof is based on CP-bit parity for a 15min /day
interval.
Counter applicable for : d3n and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.10 |
xldv20pmD3hFeSeverelyErroredSecondsCPThis read-only attribute represents a set of history
counter of Severely Errored Seconds (ES), the generation
thereof is based on CP-bit parity for a 15min /day
interval.
Counter applicable for : d3f and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.11 |
xldv20pmD3hNeSeverelyErroredSecondsPLCPThis read-only attribute represents a set of history
counter of Severely Errored Seconds (SES) for a 15min /
day interval.
Counter applicable for : d3n and F3 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.12 |
xldv20pmD3hFeSeverelyErroredSecondsPLCPThis read-only attribute represents a set of history
counter of Severely Errored Seconds (SES) for a 15min /
day interval.
Counter applicable for : d3f and F3 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.13 |
xldv20pmD3hNeCodeViolationsPThis read-only attribute represents a counter of
Code Violations Errors (Count of P-bit parity errors)
for a 15 min /day interval.
Counter applicable for : d3n and F2 level only.ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.14 |
xldv20pmD3hNeCodeViolationsCPThis read-only attribute represents a set of history
counter of Code Violations Errors (Count of CP-bit
parity errors) for a 15min /day interval.
Counter applicable for : d3n and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.15 |
xldv20pmD3hFeCodeViolationsCPThis read-only attribute represents a set of history
counter of Code Violations Errors (Count of CP-bit
parity errors) for a 15min /day interval.
Counter applicable for : d3f and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.16 |
xldv20pmD3hNeCodeViolationsPLCPThis read-only attribute represents a set of history
counter of Code Violations Errors (Count of PLCP frame
Bit Interleaved Parity errors) for a 15min /day
interval.
Counter applicable for : d3n and F3 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.17 |
xldv20pmD3hFeCodeViolationsPLCPThis read-only attribute represents a set of history
counter of Code Violations Errors (Count of PLCP frame
Bit Interleaved Parity errors) for a 15min /day
interval.
Counter applicable for : d3f and F3 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.18 |
xldv20pmD3hNeUnavailableSecondsThis read-only attribute represents a set of history
counter of Unavailable Seconds (UAS) for a 15min /day
interval.
Counter applicable for : d3n and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.19 |
xldv20pmD3hFeUnavailableSecondsThis read-only attribute represents a set of history
counter of Unavailable Seconds (UAS) for a 15min /day
interval.
Counter applicable for : d3f and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.20 |
xldv20pmD3hNeUnavailableSecondsPLCPThis read-only attribute represents a set of history
counter of Unavailable Seconds (UAS) for a 15min /day
interval.
Counter applicable for : d3n and F3 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.21 |
xldv20pmD3hFeUnavailableSecondsPLCPThis read-only attribute represents a set of history
counter of Unavailable Seconds (UAS) for a 15min /day
interval.
Counter applicable for : d3f and F3 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.22 |
xldv20pmD3hNeSasThis read-only attribute represents a set of history
counter of one second intervals containing one ore more
Severely Errored Frame (SEF) defects or one or more
Alarm Indication Signal (AIS) defects for a 15min /day
interval.
Counter applicable for : d3n and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.23 |
xldv20pmD3hFeSasThis read-only attribute represents a set of history
counter of one second intervals containing one ore more
Severely Errored Frame (SEF) defects or one or more
Alarm Indication Signal (AIS) defects for a 15min /day
interval.
Counter applicable for : d3f and F2 level only .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.7.1.24 |
xldv20pmS1CurrentTableThis table contains the entries for the current 15 minute interval
or the current day for STM1 near-end and far-end PPTPs.
Note: Day PM collection uses the 15min interval results . SEQUENCE OF Xldv20pmS1CurrentEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8 |
xldv20pmS1CurrentEntryAn entry describing the Stm1 Current Data Table . Xldv20pmS1CurrentEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1 |
xldv20pmS1cIntervalTypeThis type attribute is used to select between the
15 min or the day accumulation types.ro Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.1 |
xldv20pmS1cOAMLevelThis attribute is used to select between the
3 OAM levels f1 (1), f2 (2) and f3 (3) .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.2 |
xldv20pmS1cAdminStateThis read-write attribute is used to activate (unlock)
and deactivate (lock) the functions (incl. collection)
performed by this managed entity.
Note: the 15min collection object must be activated,
before day collection can operate.rw Xldv20AdminState .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.3 |
xldv20pmS1cSuspectFlagThis read-only attribute will be set to indicate that
troubles arose during an interval and that the counter
values are suspect and incomplete.ro Xldv20pmSuspectType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.4 |
xldv20pmS1cHistEntrySizeThis read-only attribute indicates the configured history size.
The default value is 1 and means that at least one
history entry is provided.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.5 |
xldv20pmS1cNrHistEntriesAvailableThis read-only attribute indicates how many history entries
are already available.
The range of values is between 0 and xldv20pmS1cHistEntrySize,
thereby 0 means that this entry is not valid .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.6 |
xldv20pmS1cElapsedTimeThis read-only attribute represents the difference
between the current time and the start of the present
summary interval.
Units are seconds when 15 minute interval is selected
or minutes for day interval.
(Note: accurate to the sample time interval).ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.7 |
xldv20pmS1cThresholdLimitIndexThis read-write attribute provides an index to the
ThresholdLimitTable managed entity that contains the
threshold limits for the performance parameters reported
by this managed entity.
When the value of this attribute is set to 1, default
threshold limits shall be used. These default values are
not part of the threshold limit table but are hard coded
in the application SW of PM.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.8 |
xldv20pmS1cNeErroredSecondsThis read-only attribute represents a counter of Errored
Seconds (ES) within the current 15 minute interval or current day.
Counter applicable for : s1n and F1, F2, F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.9 |
xldv20pmS1cFeErroredSecondsThis read-only attribute represents a counter of Errored
Seconds (ES) within the current 15 minute interval or current day.
Counter applicable for : s1f and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.10 |
xldv20pmS1cNeSeverelyErroredSecondsThis read-only attribute represents a counter of
Severely Errored Seconds (SES) within the current 15 minute
interval or current day.
Counter applicable for : s1n and F1, F2, F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.11 |
xldv20pmS1cFeSeverelyErroredSecondsThis read-only attribute represents a counter of
Severely Errored Seconds (SES) within the current 15 minute
interval or current day.
Counter applicable for : s1f and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.12 |
xldv20pmS1cNeBackgroundBlockErrorsThis read-only attribute represents a counter for
Background Block Errors (BBE) within the current 15 minute
interval or current day.
Counter applicable for : s1n and F1, F2, F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.13 |
xldv20pmS1cFeBackgroundBlockErrorsThis read-only attribute represents a counter for
Background Block Errors (BBE) within the current 15 minute
interval or current day.
Counter applicable for : s1f and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.14 |
xldv20pmS1cNeUnavailableSecondsThis read-only attribute represents a counter of
Unavailable Seconds (UAS) within the current 15 minute
interval or current day.
Counter applicable for : s1n and F1, F2, F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.15 |
xldv20pmS1cFeUnavailableSecondsThis read-only attribute represents a counter of
Unavailable Seconds (UAS) within the current 15 minute
interval or current day.
Counter applicable for : s1f and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.16 |
xldv20pmS1cNeOfsSecondsThis read-only attribute represents a counter of
Errored Seconds on defect OFS within the current 15 minute
interval or current day.
Counter applicable for : s1n and level F1 .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.17 |
xldv20pmS1cNeAisSecondsThis read-only attribute represents a counter of
errored Seconds on defect alarm indicatin signal AIS
for a 15 min /day interval.
Counter applicable for : s1n and F2 .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.18 |
xldv20pmS1cNeLosSecondsThis read-only attribute represents a counter of
errored Seconds on defect LOS within the current 15 minute
interval or current day.
Counter applicable for : s1n and level F1.ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.8.1.19 |
xldv20pmS1HistoryTableThis table contains the entries for the PMo objects of
the 15 min /one day-history data collection results at
the respective stm1 (s1n, s1f) drop area
interfaces . SEQUENCE OF Xldv20pmS1HistoryEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9 |
xldv20pmS1HistoryEntryAn entry describing the S1 History Data Table . Xldv20pmS1HistoryEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1 |
xldv20pmS1hIntervalTypeThis type attribute is used to select between the
15 min or the day accumulation types.ro Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.1 |
xldv20pmS1hOAMLevelThis attribute is used to select between the
3 OAM levels f1 (1), f2 (2) and f3 (3) .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.2 |
xldv20pmS1hHistEntryNrThis attribute is used as index to address a history entry.
Entry 1 is the most recent, entry 96 is 24 hours ago.
The range of values is between 1 and xldv20pmCcHistEntrySize .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.3 |
xldv20pmS1hSuspectFlagThis read-only attribute will be set to indicate that
troubles arose during an interval and that the counter
values are suspect and incomplete.ro Xldv20pmSuspectType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.4 |
xldv20pmS1hPeriodEndTimeDate/time at the end of the selected interval.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.5 |
xldv20pmS1hNeErroredSecondsThis read-only attribute represents a counter of Errored
Seconds (ES) over a 15 min /day interval.
Counter applicable for : s1n and F1, F2, F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.6 |
xldv20pmS1hFeErroredSecondsThis read-only attribute represents a counter of Errored
Seconds (ES) over a 15 min /day interval.
Counter applicable for : s1f and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.7 |
xldv20pmS1hNeSeverelyErroredSecondsThis read-only attribute represents a counter of
Severely Errored Seconds (SES) over a 15 min /day
interval.
Counter applicable for : s1n and F1, F2, F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.8 |
xldv20pmS1hFeSeverelyErroredSecondsThis read-only attribute represents a counter of
Severely Errored Seconds (SES) over a 15 min /day
interval.
Counter applicable for : s1f and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.9 |
xldv20pmS1hNeBackgroundBlockErrorsThis read-only attribute represents a counter for
Background Block Errors (BBE) over a 15 min /day
interval.
Counter applicable for : s1n and F1, F2, F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.10 |
xldv20pmS1hFeBackgroundBlockErrorsThis read-only attribute represents a counter for
Background Block Errors (BBE) over a 15 min /day
interval.
Counter applicable for : s1f and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.11 |
xldv20pmS1hNeUnavailableSecondsThis read-only attribute represents a counter of
Unavailable Seconds (UAS) for a 15 min /day interval.
Counter applicable for : s1n and F1, F2, F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.12 |
xldv20pmS1hFeUnavailableSecondsThis read-only attribute represents a counter of
Unavailable Seconds (UAS) for a 15 min /day interval.
Counter applicable for : s1f and F2 and F3 levels .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.13 |
xldv20pmS1hNeOfsSecondsThis read-only attribute represents a counter of
Errored Seconds on defect OFS for a 15 min /day interval.
Counter applicable for : s1n and level F1 .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.14 |
xldv20pmS1hNeAisSecondsThis read-only attribute represents a counter of
errored Seconds on defect alarm indicatin signal AIS
for a 15 min /day interval.
Counter applicable for : s1n and level F2 .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.15 |
xldv20pmS1hNeLosSecondsThis read-only attribute represents a counter of
errored Seconds on defect LOS for a 15 min /day interval.
Counter applicable for : s1n and F1 .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.9.1.16 |
xldv20pmAtmObjectsTableThis table contains the entries for the PMo objects
on ATM layer. Maximum of monitored connections is 128. SEQUENCE OF Xldv20pmAtmObjectsEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.10 |
xldv20pmAtmObjectsEntryAn entry of the xldv20pmAtmObjectsTable. Xldv20pmAtmObjectsEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.10.1 |
xldv20pmAoIndexIdentifies an entry of the xldv20pmAtmObjectsTable.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.10.1.1 |
xldv20pmAoFlowTypeThis attribute identifies the flow type :
F4 (VP) or F5 (VC) segment or endToEnd flow.ro Xldv20pmFlowType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.10.1.2 |
xldv20pmAoAdminStateThis read-write attribute is used to activate (unlock)
and deactivate (lock) the functions (incl. collection)
performed by this managed entity.
Note: the 15min collection object must be activated,
before day collection can operate.rw Xldv20AdminState .1.3.6.1.4.1.231.7.1.2.1.1.5.2.10.1.3 |
xldv20pmAoBlockSizeThis is the number of user cells after which
PMo cell is inserted. Default is 128.rw Xldv20pmBlockSizeType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.10.1.4 |
xldv20pmAtmEndpointsTableThis table contains the enpoints for PMo on Atm layer. SEQUENCE OF Xldv20pmAtmEndpointsEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.11 |
xldv20pmAtmEndpointsEntryAn entry of xldv20pmAtmEndpointsTable. Xldv20pmAtmEndpointsEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.11.1 |
xldv20pmAeEndpointTypeIdentifies the type of endpoint.ro Xldv20pmEndpointType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.11.1.1 |
xldv20pmAeConnectionIndexThis attribute identifies the Vpl or Vcl cross connection
where an endpoint object should be added.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.11.1.2 |
xldv20pmAeConnectionIndexTypeThis attribute identifies the type of connection index
and the termination point where an endpoint should be added.ro Xldv20pmConnectionIndexType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.11.1.3 |
xldv20pmAeRoleThe role of endpoint.
'analyseWithBackwardReporting' (sink) means extracting
forward monitoring (FM) OAM cells, sending back
backward reporting OAM cells and no data collection
for current and history table.
'analyseWithoutBackwardReporting' (sink) means extracting
FM cells and also collecting data.
'generateWithCollect' (source) means inserting FM cells,
extracting backward reporting cells if they arrive
and collect data for current and history table.
'generateWithoutCollect' (source) means inserting FM cells
but without collecting data.
The CMU, the Ethernet part of the Twin NT can be
inserting and extracting points.ro Xldv20pmRoleType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.11.1.4 |
xldv20pmAeFlowDirectionThis attribute identifies the flow direction.
inwards means flow direction from outside (external interface)
to cross connection.
outwards means flow direction from inside to external interface.ro Xldv20FlowDirection .1.3.6.1.4.1.231.7.1.2.1.1.5.2.11.1.5 |
xldv20pmAtmCurrentTableThis table contains the entries for the the PMo objects
for the current data of Pmo monitoring objects
on ATM layer.
It includes attributes for performance parameters,
collection interval is 15 minutes and one day . SEQUENCE OF Xldv20pmAtmCurrentEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.12 |
xldv20pmAtmCurrentEntryAn entry describing the Atm Current Data Table . Xldv20pmAtmCurrentEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1 |
xldv20pmAcIntervalTypeThis type attribute is used to select between the
15 min or the day accumulation types.ro Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.1 |
xldv20pmAcAdminStateThis read-write attribute is used to activate (unlock)
and deactivate (lock) the functions (incl. collection)
performed by this managed entity.
Note: the 15min collection object must be activated,
before day collection can operate.rw Xldv20AdminState .1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.2 |
xldv20pmAcSuspectFlagThis read-only attribute will be set to indicate that
troubles arose during an interval and that the counter
values are suspect and incomplete.ro Xldv20pmSuspectType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.3 |
xldv20pmAcHistEntrySizeThis is the configured size of history.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.4 |
xldv20pmAcNrHistEntriesAvailableThis is the number of history entries which
are available in the history table.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.5 |
xldv20pmAcElapsedTimeThis read-only attribute represents the difference
between the current time and the start of the present
summary interval.
Units are seconds when 15 minute interval is selected
or minutes for day interval.
(Note: accurate to the sample time interval).ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.6 |
xldv20pmAcThresholdLimitIndexThis read-write attribute provides an index to the
ThresholdLimitTable managed entity that contains the
threshold limits for the performance parameters reported
by this managed entity.
When the value of this attribute is set to 1, default
threshold limits shall be used .rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.7 |
xldv20pmAcTransmittedUserCellsThis read-only attribute represents a counter of
transmitted user cells for a 15 min /day interval.ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.8 |
xldv20pmAcLostUserCellsThis read-only attribute represents a counter of
lost user cells for a 15 min /day interval.ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.9 |
xldv20pmAcMisinsertedUserCellsThis read-only attribute represents a counter of
Misinserted user cells for a 15 min /day interval.ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.12.1.10 |
xldv20pmAtmHistoryTableThis table contains the entries for the 15 min /one
day-history data collection results for PMo objects
of ATM layer. SEQUENCE OF Xldv20pmAtmHistoryEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.13 |
xldv20pmAtmHistoryEntryAn entry describing the History Data Table for PMo on ATM
layer. Xldv20pmAtmHistoryEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.13.1 |
xldv20pmAhIntervalTypeThis type attribute is used to select between the
15 min or the day accumulation types.ro Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.13.1.1 |
xldv20pmAhHistEntryNrThis attribute is used as index to address a history entry.
Entry 1 is the most recent, entry 96 is 24 hours ago.
The range of values is between 1 and xldv20pmAcHistEntrySize .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.13.1.2 |
xldv20pmAhSuspectFlagThis read-only attribute will be set to indicate that
troubles arose during an interval and that the counter
values are suspect and incomplete.ro Xldv20pmSuspectType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.13.1.3 |
xldv20pmAhPeriodEndTimeDate/time at the end of the selected interval.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.13.1.4 |
xldv20pmAhTransmittedUserCellsThis read-only attribute represents a counter of
transmitted user cells for a 15 min /day interval.ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.13.1.5 |
xldv20pmAhLostUserCellsThis read-only attribute represents a counter of
lost user cells for a 15 min /day interval.ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.13.1.6 |
xldv20pmAhMisinsertedUserCellsThis read-only attribute represents a counter of
Misinserted user cells for a 15 min /day interval.ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.2.13.1.7 |
xldv20pmImaGroupCurrentTableThis table contains the entries for the PMo objects
for the current data of Pmo monitoring objects
for IMA groups .
Collection interval is the current 15 minute and one the
current day . SEQUENCE OF Xldv20pmImaGroupCurrentEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.14 |
xldv20pmImaGroupCurrentEntryAn entry describing the current PMo data for ImaGroups. Xldv20pmImaGroupCurrentEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1 |
xldv20pmImaGroupCurrentIntervalTypeThis type attribute is used to select between the
15 min or the day accumulation types.ro Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.1 |
xldv20pmImaGroupCurrentAdminStateThis read-write attribute is used to activate (unlock)
and deactivate (lock) the functions (incl. collection)
performed by this managed entity.
Note: the 15min collection object must be activated,
before day collection can operate.rw Xldv20AdminState .1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.2 |
xldv20pmImaGroupCurrentSuspectFlagThis read-only attribute will be set to indicate that
troubles arose during an interval and that the counter
values are suspect and incomplete.ro Xldv20pmSuspectType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.3 |
xldv20pmImaGroupCurrentHistEntrySizeThis is the configured size of history.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.4 |
xldv20pmImaGroupCurrentNrHistEntriesAvailableThis is the number of history entries which
are available in the history table.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.5 |
xldv20pmImaGroupCurrentElapsedTimeThis read-only attribute represents the difference
between the current time and the start of the present
summary interval.
Units are seconds when 15 minute interval is selected
or minutes for day interval.
(Note: accurate to the sample time interval).ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.6 |
xldv20pmImaGroupCurrentThresholdLimitIndexThis read-write attribute provides an index to the
ThresholdLimitTable managed entity that contains the
threshold limits for the performance parameters reported
by this managed entity.
When the value of this attribute is set to 1, default
threshold limits shall be used .rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.7 |
xldv20pmImaGroupCurrentUnavailSecsThe counts of second intervals where the IMA group
traffic state machine is down in the current
for a 15 min /day interval.ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.8 |
xldv20pmImaGroupCurrentNeNumFailuresThe number of times a near-end group failure
(config-Aborted, unsufficient-Links) has been reported
for a 15 min /day interval.ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.14.1.9 |
xldv20pmImaGroupHistoryTableThis table contains the entries for the 15 min /one
day-history data collection results for PMo objects
of IMA Group interfaces. SEQUENCE OF Xldv20pmImaGroupHistoryEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.15 |
xldv20pmImaGroupHistoryEntryAn entry describing the History Data Table for PMo
IMA groups. Xldv20pmImaGroupHistoryEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.15.1 |
xldv20pmImaGroupHistoryIntervalTypeThis type attribute is used to select between the
15 min or the day accumulation types.ro Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.15.1.1 |
xldv20pmImaGroupHistoryHistEntryNrThis attribute is used as index to address a history entry.
Entry 1 is the most recent, entry 96 is 24 hours ago.
The range of values is between 1 and xldv20pmImaGroupCurrentHistEntrySize .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.15.1.2 |
xldv20pmImaGroupHistorySuspectFlagThis read-only attribute will be set to indicate that
troubles arose during an interval and that the counter
values are suspect and incomplete.ro Xldv20pmSuspectType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.15.1.3 |
xldv20pmImaGroupHistoryPeriodEndTimeDate/time at the end of the selected interval.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.15.1.4 |
xldv20pmImaGroupHistoryUnavailSecsThe counts of second intervals where the IMA group
traffic state machine is down in the current
15 min /day interval.ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.15.1.5 |
xldv20pmImaGroupHistoryNeNumFailuresThe number of times a near-end group failure
(config-Aborted, unsufficient-Links) has been reported
for a previous 15 min interval or the previous day.ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.15.1.6 |
xldv20pmImaLinkCurrentTableThis table contains the entries for the the PMo objects
for the current data of Pmo monitoring objects
for IMA groups .
It includes attributes for performance parameters,
collection interval is 15 minutes and one day . SEQUENCE OF Xldv20pmImaLinkCurrentEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16 |
xldv20pmImaLinkCurrentEntryAn entry describing the current PMo data for ImaLinks. Xldv20pmImaLinkCurrentEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1 |
xldv20pmImaLinkCurrentIntervalTypeThis type attribute is used to select between the
15 min or the day accumulation types.ro Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.1 |
xldv20pmImaLinkCurrentAdminStateThis read-write attribute is used to activate (unlock)
and deactivate (lock) the functions (incl. collection)
performed by this managed entity.
Note: the 15min collection object must be activated,
before day collection can operate.rw Xldv20AdminState .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.2 |
xldv20pmImaLinkCurrentSuspectFlagThis read-only attribute will be set to indicate that
troubles arose during an interval and that the counter
values are suspect and incomplete.ro Xldv20pmSuspectType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.3 |
xldv20pmImaLinkCurrentHistEntrySizeThis is the configured size of history.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.4 |
xldv20pmImaLinkCurrentNrHistEntriesAvailableThis is the number of history entries which
are available in the history table.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.5 |
xldv20pmImaLinkCurrentElapsedTimeThis read-only attribute represents the difference
between the current time and the start of the present
summary interval.
Units are seconds when 15 minute interval is selected
or minutes for day interval.
(Note: accurate to the sample time interval).ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.6 |
xldv20pmImaLinkCurrentThresholdLimitIndexThis read-write attribute provides an index to the
ThresholdLimitTable managed entity that contains the
threshold limits for the performance parameters reported
by this managed entity.
When the value of this attribute is set to 1, default
threshold limits shall be used .rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.7 |
xldv20pmImaLinkCurrentImaViolationsICP violations: count of errored, invalid or missing ICP cells,
except during SES-IMA or UAS-IMA conditions, in the current
15 minute interval.
ATM Forum IMA v1.1, (R-125) and (O-26) in Section 12.2.2.2
on page 77.ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.8 |
xldv20pmImaLinkCurrentOifAnomaliesThe number of OIF anomalies, except during SES-IMA or UAS-IMA
conditions, at the near-end in the current 15 minute interval.
This is an optional attribute.
ATM Forum IMA v1.1, (O-20) and (O-26) in Section 12.2.2.2
on page 77ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.9 |
xldv20pmImaLinkCurrentNeSevErroredSecsCount of one second intervals containing >= 30% of the ICP cells
counted as IV-IMAs, or one or more link defects (e.g., LOS, OOF/LOF,
AIS, or LCD), LIF defects, or LODS defects, except during UAS-IMA
condition, in the current 15 minute interval.
ATM Forum IMA v1.1, (R-126) and (O-26) in Section 12.2.2.2
on page 77ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.10 |
xldv20pmImaLinkCurrentFeSevErroredSecsCount of unavailable seconds at near-end in the current 15 minute
interval: unavailability begins at the onset of 10 contiguous
SES-IMA and ends at the onset of 10 contiguous seconds with no
SES-IMA.
ATM Forum IMA v1.1, (R-128) and (O-26) in Section 12.2.2.2 on page 77ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.11 |
xldv20pmImaLinkCurrentNeUnavailSecsCount of unavailable seconds at near-end in the current 15 minute
interval: unavailability begins at the onset of 10 contiguous
SES-IMA-FE and ends at the onset of 10 contiguous seconds with no
SES-IMA-FE.
ATM Forum IMA v1.1, (R-129) and (O-26) in Section 12.2.2.2
on page 77 .ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.12 |
xldv20pmImaLinkCurrentFeUnavailSecsCount of unavailable seconds at far-end in the current 15 minute
interval: unavailability begins at the onset of 10 contiguous
SES-IMA-FE and ends at the onset of 10 contiguous seconds with no
SES-IMA-FE.
ATM Forum IMA v1.1, (R-129) and (O-26) in Section 12.2.2.2
on page 77 .ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.13 |
xldv20pmImaLinkCurrentNeTxUnusableSecsTx Unusable seconds: count of Unusable seconds at the near-end
Tx LSM in the current 15 minute interval.
ATM Forum IMA v1.1, (R-130) and (O-26) in Section 12.2.2.2
on page 77.ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.14 |
xldv20pmImaLinkCurrentNeRxUnusableSecsRx Unusable seconds: count of Unusable seconds at the near-end
Rx LSM in the current 15 minute interval.
ATM Forum IMA v1.1, (R-131) and (O-26) in Section 12.2.2.2
on page 77.ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.15 |
xldv20pmImaLinkCurrentFeTxUnusableSecsTx Unusable seconds: count of Unusable seconds at the far-end
Tx LSM in the current 15 minute interval.
ATM Forum IMA v1.1, (R-132) and (O-26) in Section 12.2.2.2
on page 77.ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.16 |
xldv20pmImaLinkCurrentFeRxUnusableSecsRx Unusable seconds: count of Unusable seconds at the far-end
Rx LSM in the current 15 minute interval.
ATM Forum IMA v1.1, (R-133) and (O-26) in Section 12.2.2.2
on page 77.ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.17 |
xldv20pmImaLinkCurrentNeTxNumFailuresThe number of times a near-end transmit failure alarm condition
has been entered on this link (i.e., some form of implementation
specific transmit fault) in the current 15 minute interval.
ATM Forum IMA v1.1, (R-134) and (O-26) in Section 12.2.2.2
on page 77ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.18 |
xldv20pmImaLinkCurrentNeRxNumFailuresThe number of times a near-end receive failure alarm condition
has been entered on this link (i.e., LIF, LODS, RFI-IMA, Mis-Connected,
or some form of implementation specific receive fault)
in the current 15 minute interval.
ATM Forum IMA v1.1, (R-135) and (O-26) in Section 12.2.2.2
on page 77ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.16.1.19 |
xldv20pmImaLinkHistoryTableThis table contains the entries for the 15 min /one
day-history data collection results for PMo objects
of IMA Link interfaces. SEQUENCE OF Xldv20pmImaLinkHistoryEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17 |
xldv20pmImaLinkHistoryEntryAn entry describing the History Data Table for PMo
IMA groups. Xldv20pmImaLinkHistoryEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1 |
xldv20pmImaLinkHistoryIntervalTypeThis type attribute is used to select between the
15 min or the day accumulation types.ro Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.1 |
xldv20pmImaLinkHistoryHistEntryNrThis attribute is used as index to address a history entry.
Entry 1 is the most recent, entry 96 is 24 hours ago.
The range of values is between 1 and xldv20pmImaLinkCurrentHistEntrySize .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.2 |
xldv20pmImaLinkHistorySuspectFlagThis read-only attribute will be set to indicate that
troubles arose during an interval and that the counter
values are suspect and incomplete.ro Xldv20pmSuspectType .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.3 |
xldv20pmImaLinkHistoryPeriodEndTimeDate/time at the end of the selected interval.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.4 |
xldv20pmImaLinkHistoryImaViolationsICP violations: count of errored, invalid or missing ICP cells,
except during SES-IMA or UAS-IMA conditions,
in one of the previous 96, individual 15 minute, intervals
or the previous day.
ATM Forum IMA v1.1, (R-125) and (O-26) in Section 12.2.2.2
on page 77.ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.5 |
xldv20pmImaLinkHistoryOifAnomaliesThe number of OIF anomalies, except during SES-IMA or UAS-IMA
conditions, at the near-end in one of the previous 96,
individual 15 minute, intervals or the previous day.
This is an optional attribute.
ATM Forum IMA v1.1, (O-20) and (O-26) in Section 12.2.2.2
on page 77ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.6 |
xldv20pmImaLinkHistoryNeSevErroredSecsCount of one second intervals containing >= 30% of the ICP cells
counted as IV-IMAs, or one or more link defects (e.g., LOS, OOF/LOF,
AIS, or LCD), LIF defects, or LODS defects, except during UAS-IMA
condition, in one of the previous 96, individual 15 minute, intervals
or the previous day.
ATM Forum IMA v1.1, (R-126) and (O-26) in Section 12.2.2.2
on page 77ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.7 |
xldv20pmImaLinkHistoryFeSevErroredSecsCount of unavailable seconds at near-end
in one of the previous 96, individual 15 minute, intervals
or the previous day.
Unavailability begins at the onset of 10 contiguous
SES-IMA and ends at the onset of 10 contiguous seconds with no
SES-IMA.
ATM Forum IMA v1.1, (R-127) and (O-26) in Section 12.2.2.2 on page 77ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.8 |
xldv20pmImaLinkHistoryNeUnavailSecsCount of unavailable seconds at near-end
in one of the previous 96, individual 15 minute, intervals
or the previous day.
Unavailability begins at the onset of 10 contiguous
SES-IMA and ends at the onset of 10 contiguous seconds with no
SES-IMA.
ATM Forum IMA v1.1, (R-128) and (O-26) in Section 12.2.2.2
on page 77 .ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.9 |
xldv20pmImaLinkHistoryFeUnavailSecsCount of unavailable seconds at far-end
in one of the previous 96, individual 15 minute, intervals
or the previous day.
Unavailability begins at the onset of 10 contiguous
SES-IMA-FE and ends at the onset of 10 contiguous seconds with no
SES-IMA-FE.
ATM Forum IMA v1.1, (R-129) and (O-26) in Section 12.2.2.2
on page 77 .ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.10 |
xldv20pmImaLinkHistoryNeTxUnusableSecsTx Unusable seconds: count of Unusable seconds at the near-end
Tx LSM in one of the previous 96, individual 15 minute, intervals
or the previous day.
ATM Forum IMA v1.1, (R-130) and (O-26) in Section 12.2.2.2
on page 77.ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.11 |
xldv20pmImaLinkHistoryNeRxUnusableSecsRx Unusable seconds: count of Unusable seconds at the near-end
Rx LSM in one of the previous 96, individual 15 minute, intervals
or the previous day.
ATM Forum IMA v1.1, (R-131) and (O-26) in Section 12.2.2.2
on page 77.ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.12 |
xldv20pmImaLinkHistoryFeTxUnusableSecsTx Unusable seconds: count of Unusable seconds at the far-end
Tx LSM in one of the previous 96, individual 15 minute, intervals
or the previous day.
ATM Forum IMA v1.1, (R-132) and (O-26) in Section 12.2.2.2
on page 77.ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.13 |
xldv20pmImaLinkHistoryFeRxUnusableSecsRx Unusable seconds: count of Unusable seconds at the far-end
Rx LSM in one of the previous 96, individual 15 minute, intervals
or the previous day.
ATM Forum IMA v1.1, (R-133) and (O-26) in Section 12.2.2.2
on page 77.ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.14 |
xldv20pmImaLinkHistoryNeTxNumFailuresThe number of times a near-end transmit failure alarm condition
has been entered on this link (i.e., some form of implementation
specific transmit fault) in one of the previous 96,
individual 15 minute, intervals or the previous day.
ATM Forum IMA v1.1, (R-134) and (O-26) in Section 12.2.2.2
on page 77ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.15 |
xldv20pmImaLinkHistoryNeRxNumFailuresThe number of times a near-end receive failure alarm condition
has been entered on this link (i.e., LIF, LODS, RFI-IMA, Mis-Connected,
or some form of implementation specific receive fault)
in one of the previous 96, individual 15 minute, intervals
or the previous day.
ATM Forum IMA v1.1, (R-135) and (O-26) in Section 12.2.2.2
on page 77ro Gauge .1.3.6.1.4.1.231.7.1.2.1.1.5.2.17.1.16 |
xldv20pmProtocolMonitoring OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.1.1.5.3 |
xldv20pmTcaPrMCurrentTableThis table contains the entries for the PrM object at
the following tca layer locations:
- STM1 interface (in downstream direction)
- STS3-c interface (in downstream direction)
- E3 interface (in downstream direction)
- DS3 interface (in downstream direction)
- SU_AD16 interfaces (in upstream stream direction).
PrM also possible at IMA groups.
It includes attributes for performance parameters,
collection interval is 15 min /one day . SEQUENCE OF Xldv20pmTcaPrMCurrentEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.3.1 |
xldv20pmTcaPrMCurrentEntryAn entry describing the TC-Adaptor Current Data Table
. Xldv20pmTcaPrMCurrentEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1 |
xldv20pmTcIntervalTypeThis nac type attribute is used to select between the
15 min or the day accumulation types.ro Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1.1 |
xldv20pmTcAdminStateThis read-write attribute is used to activate (unlock)
and deactivate (lock) the functions (incl. collection)
performed by this managed entity.
Note: the 15min collection object must be activated,
before day collection can operate.rw Xldv20AdminState .1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1.2 |
xldv20pmTcSuspectFlagThis read-only attribute will be set to indicate that
troubles arose during an interval and that the counter
values are suspect and incomplete.ro Xldv20pmSuspectType .1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1.3 |
xldv20pmTcHistEntrySizeThis read-only attribute indicates the number of 15min
history entries configured for the particular interface.
The default value is 1 and means that at least one
history entry is provided.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1.4 |
xldv20pmTcNrHistEntriesAvailableThis read-only attribute indicates how many HistEntries
are already available.
The range of values is between 0 and xldv20pmTcHistEntrySize,
thereby 0 means that this entry is not valid .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1.5 |
xldv20pmTcElapsedTimeThis read-only attribute represents the difference
between the current time and the start of the present
summary interval.
Units are seconds when 15 minute interval is selected
or minutes for day interval.
(Note: accurate to the sample time interval).ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1.6 |
xldv20pmTcThresholdLimitIndexThis read-write attribute provides an index to the
ThresholdLimitTable managed entity that contains the
threshold limits for the performance parameters reported
by this managed entity.
When the value of this attribute is set to 1, default
threshold limits shall be used. These default values are
not part of the threshold limit table but are hard coded
in the application SW of PM.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1.7 |
xldv20pmTcDiscardedCellsThis read-only attribute represents a counter of the
number of ATM cells discarded at this interface, due to
a HEC violation, since the start of this interval .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.3.1.1.8 |
xldv20pmTcaPrMHistoryTableThis table contains the entries for the PrM history
object at the different tca layer locations. It contains
results that are overtaken from the TcaPrMCurrentTable
PM-object at the end of a 15 min /day interval . SEQUENCE OF Xldv20pmTcaPrMHistoryEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.3.2 |
xldv20pmTcaPrMHistoryEntryAn entry describing the TC-Adaptor History Data Table
. Xldv20pmTcaPrMHistoryEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.3.2.1 |
xldv20pmThIntervalTypeThis type attribute is used to select between the
15 min or the day accumulation types.ro Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.3.2.1.1 |
xldv20pmThHistEntryNrThis attribute is used as index to address a history entry.
Entry 1 is the most recent, entry 96 is 24 hours ago.
The range of values is between 1 and xldv20pmTcHistEntrySize.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.3.2.1.2 |
xldv20pmThSuspectFlagThis read-only attribute will be set to indicate that
troubles arose during an interval and that the counter
values are suspect and incomplete.ro Xldv20pmSuspectType .1.3.6.1.4.1.231.7.1.2.1.1.5.3.2.1.3 |
xldv20pmThPeriodEndTimeThis read-only attribute is a record of date/time at the
end of an interval .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.3.2.1.4 |
xldv20pmThDiscardedCellsThis read-only attribute represents a set of history
counter of the number of ATM cells discarded at this
interface, due to a HEC violation, since the start of
this interval .ro Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.3.2.1.5 |
xldv20pmThresholding OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.1.1.5.4 |
xldv20pmThresholdLimitTableThe threshold limit table for all interface.
This table associates threshold limit index/PM counter
pairs with threshold limit values for a 15 minutes
interval. Entries with same threshold limit index
belong to the same threshold limit profile.
Each of the following TC-adaptor types are available
and can be configured: adc, s1n, s3n, d3n, e3n.
A crossing of a threshold limit leads to a
threshold crossing alert. SEQUENCE OF Xldv20pmThresholdLimitEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1 |
xldv20pmThresholdLimitEntryAn entry describing the threshold limit information . Xldv20pmThresholdLimitEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1 |
xldv20pmThlThresholdLimitIndexThis read-only attribute selects a profile out of the
threshold limit table .ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.1 |
xldv20pmThlNeBackgroundBlockErrorsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.2 |
xldv20pmThlNeCodeViolationsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.3 |
xldv20pmThlNeCodeViolationsCPThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.4 |
xldv20pmThlNeCodeViolationsPThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.5 |
xldv20pmThlNeCodeViolationsPLCPThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.6 |
xldv20pmThlNeErroredSecondsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.7 |
xldv20pmThlNeErroredSecondsCPThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.8 |
xldv20pmThlNeErroredSecondsPLCPThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.9 |
xldv20pmThlNeSasThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.10 |
xldv20pmThlNeSeverelyErroredFrameSecondsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.11 |
xldv20pmThlNeSeverelyErroredSecondsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.12 |
xldv20pmThlNeSeverelyErroredSecondsCPThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.13 |
xldv20pmThlNeSeverelyErroredSecondsPLCPThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.14 |
xldv20pmThlNeUnavailableSecondsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.15 |
xldv20pmThlNeUnavailableSecondsPLCPThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.16 |
xldv20pmThlNeAisSecondsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.17 |
xldv20pmThlNeOfsSecondsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.18 |
xldv20pmThlNeLosSecondsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.19 |
xldv20pmThlFeBackgroundBlockErrorsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.20 |
xldv20pmThlFeCodeViolationsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.21 |
xldv20pmThlFeCodeViolationsCPThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.22 |
xldv20pmThlFeCodeViolationsPLCPThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.23 |
xldv20pmThlFeErroredSecondsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.24 |
xldv20pmThlFeErroredSecondsCPThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.25 |
xldv20pmThlFeErroredSecondsPLCPThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.26 |
xldv20pmThlFeSasThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.27 |
xldv20pmThlFeSeverelyErroredSecondsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.28 |
xldv20pmThlFeSeverelyErroredSecondsCPThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.29 |
xldv20pmThlFeSeverelyErroredSecondsPLCPThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.30 |
xldv20pmThlFeUnavailableSecondsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.31 |
xldv20pmThlFeUnavailableSecondsPLCPThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.32 |
xldv20pmThlDiscardedCellsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.33 |
xldv20pmThlImaGroupUnavailSecsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.34 |
xldv20pmThlImaGroupNeNumFailuresThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.35 |
xldv20pmThlImaLinkImaViolationsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.36 |
xldv20pmThlImaLinkOifAnomaliesThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.37 |
xldv20pmThlImaLinkNeSevErroredSecsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.38 |
xldv20pmThlImaLinkFeSevErroredSecsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.39 |
xldv20pmThlImaLinkNeUnavailSecsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.40 |
xldv20pmThlImaLinkFeUnavailSecsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.41 |
xldv20pmThlImaLinkNeTxUnusableSecsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.42 |
xldv20pmThlImaLinkNeRxUnusableSecsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.43 |
xldv20pmThlImaLinkFeTxUnusableSecsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.44 |
xldv20pmThlImaLinkFeRxUnusableSecsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.45 |
xldv20pmThlImaLinkNeTxNumFailuresThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.46 |
xldv20pmThlImaLinkNeRxNumFailuresThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.1.1.47 |
xldv20pmAtmThresholdLimitTableThe threshold limit table for all interface.
This table associates threshold limit index/PM counter
pairs with threshold limit values for a 15 minutes
interval. Entries with same threshold limit index
belong to the same threshold limit profile.
A crossing of a threshold limit leads to a
threshold crossing alert. SEQUENCE OF Xldv20pmAtmThresholdLimitEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.4.2 |
xldv20pmAtmThresholdLimitEntryAn entry describing the threshold limit information . Xldv20pmAtmThresholdLimitEntry .1.3.6.1.4.1.231.7.1.2.1.1.5.4.2.1 |
xldv20pmAtlThresholdLimitIndexThis read-only attribute selects a profile out of the
threshold limit table of PM on ATM layer.ro INTEGER .1.3.6.1.4.1.231.7.1.2.1.1.5.4.2.1.1 |
xldv20pmAtlTransmittedUserCellsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.1.1.5.4.2.1.2 |
xldv20pmAtlLostUserCellsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.1.1.5.4.2.1.3 |
xldv20pmAtlMisinsertedUserCellsThis read-write attribute selects the threshold limit value
of the counter in the current threshold limit profile.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.1.1.5.4.2.1.4 |
xldv20pmTraps OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.1.1.5.5 |
xldv20pmTrapVars OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.1.1.5.5.1 |
xldv20pmTvIfIndexThe interface index of the reporting PM object. Unsigned16 (XLDV20-MIB) .1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.1 |
xldv20pmTvPmTypeSpecifies the reporting PM object and OAM level. Xldv20pmType .1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.2 |
xldv20pmTvPmCounterIdentifies the PM counter. Xldv20pmCounterName .1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.3 |
xldv20pmTvCurrentCounterValueThe actual counter value at detection. Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.4 |
xldv20pmTvCurrentCounterLimitThe current value of threshold limit. Counter .1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.5 |
xldv20pmTvAtmPmCounterIdentifies the performance parameter. Xldv20pmAtmCounterType .1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.6 |
xldv20pmTvAtmObjectIndexIdentifies the AtmPm object. Unsigned16 (XLDV20-MIB) .1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.7 |
xldv20pmTvEndpointTypeIdentifies the type of endpoint. Xldv20pmEndpointType .1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.8 |
xldv20pmTvIntervalTypeIdentifies the type of interval. Xldv20pmIntervalType .1.3.6.1.4.1.231.7.1.2.1.1.5.5.1.9 |
xldv20pmTrapTypes OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.1.1.5.5.2 |