SHE-ADSL-MIB
AI MIB Summary
The SHE-ADSL-MIB extends the standard ADSL-LINE-MIB to monitor proprietary ADSL line, physical layer, and channel performance metrics, including signal attenuation, noise margins, error counts, and configuration profiles for ATUC and ATUR interfaces. It facilitates granular management of ADSL line configurations, alarm thresholds, and traffic profiles via specific tables for physical parameters, performance data intervals, and virtual circuit types.
The MIB module to describe ADSL product. The MIB module that provides objects that are proprietary and extension to ADSL- LINE-MIB.The MIB includes the following Tables. 1.) adslLineTable 2.) adslAtucPhysTable 3.) adslAturPhysTable 4.) adslAtucChanTable 5.) adslAturChanTable 6.) adslAtucPerfDataTable 7.) adslAtucIntervalTable 8.) adslAtucChanPerfDataTable 9.) adslAturChanPerfDataTable 10.) adslAtucChanIntervalTable 11.) adslAturChanIntervalTable 12.) adslLineConfProfileTable 13.) adslLineConfExtnProfileTable 13.) adslLineAlarmConfProfileTable 14.) adslVccTpTable 15.) adslRfiMaskTable
Main OID:
sheAdslMib.1.3.6.1.4.1.231.7.1.2.2.1.6
868
Objects
Active
Status
10
Dependencies
Imported Objects
Objects
868 total| Object Name |
|---|
sheAdslMibThe MIB module to describe ADSL product. The MIB module that provides objects that are proprietary and extension to ADSL- LINE-MIB.The MIB includes the following Tables. 1.) adslLineTable 2.) adslAtucPhysTable 3.) adslAturPhysTable 4.) adslAtucChanTable 5.) adslAturChanTable 6.) adslAtucPerfDataTable 7.) adslAtucIntervalTable 8.) adslAtucChanPerfDataTable 9.) adslAturChanPerfDataTable 10.) adslAtucChanIntervalTable 11.) adslAturChanIntervalTable 12.) adslLineConfProfileTable 13.) adslLineConfExtnProfileTable 13.) adslLineAlarmConfProfileTable 14.) adslVccTpTable 15.) adslRfiMaskTable MODULE-IDENTITY .1.3.6.1.4.1.231.7.1.2.2.1.6 |
sheAdslMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1 |
sheAdslLineMIB OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1 |
sheDslSystemParamGroup OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.1 |
sheDslSystemDslTypeThis object identifies the firmware to be downloaded. adsl(1), sdsl(2), shdsl(3)ro SheDslSystemType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.1.1 |
sheDslSystemLineCodingTypeThis object indicates ADSL line code type. other(1), dmt(2), cap(3), qam(4)ro SheDslSystemLineCodingType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.1.2 |
sheDslSystemLineTxCfgThis object indicates transmission capabilities with which the DSL system is configured. unused(0), etsi(1), q9921PotsNonOverlapped(2), q9921PotsOverlapped(3), q9921IsdnNonOverlapped(4), q9921IsdnOverlapped(5), q9921TcmIsdnNonOverlapped(6), q9921TcmIsdnOverlapped(7), q9922PotsNonOverlapped(8), q9922PotsOverlapped(9), q9922TcmIsdnNonOverlapped(10), q9922TcmIsdnOverlapped(11), q9922TcmIsdnSymmetric(12), adslPlusPotsNonOverlapped(13)ro SheDslSystemTxCfgType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.1.3 |
sheDslSystemParamControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.2 |
sheDslSystemParamControlRequestsetDslSystemLineTxCfg: sheDslSystemParamControlLineTxCfgrw SheAdslControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.2.1 |
sheDslSystemParamControlStatusThe status of a user command.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.2.2 |
sheDslSystemParamControlTimerThe maximum wait time for the manager for a long running user command.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.2.3 |
sheDslSystemParamControlReqResultThe result of the last user command.ro SheAdslControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.2.4 |
sheDslSystemParamControlTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.2.5 |
sheDslSystemParamControlLineTxCfgThis object indicates transmission capabilities with which the DSL system is configured.rw SheDslSystemTxCfgType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.2.6 |
sheAdslSystemCapabilityGroup OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.3 |
sheAdslCapabilityLineTxCapThis bitmap specifies all transmission modes, which the ATU-C is capable of supporting. Right now support for Annex A (q9921PotsNonOverlapped(2) and q9921PotsOverlapped(3)) is present. This value depends on the DSL PHY firmware present on Columbia MND unused(0), etsi(1), q9921PotsNonOverlapped(2), q9921PotsOverlapped(3), q9921IsdnNonOverlapped(4), q9921IsdnOverlapped(5), q9921TcmIsdnNonOverlapped(6), q9921TcmIsdnOverlapped(7), q9922PotsNonOverlapped(8), q9922PotsOverlapped(9), q9922TcmIsdnNonOverlapped(10), q9922TcmIsdnOverlapped(11), q9922TcmIsdnSymmetric(12), adslPlusPotsNonOverlapped(13)ro SheDslSystemTxCfgType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.3.1 |
sheAdslLineConfProfileTableThis table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the ADSL line. SEQUENCE OF SheAdslLineConfProfileEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4 |
sheAdslLineConfProfileEntryEach entry consists of a list of parameters that represents the configuration of an ADSL modem. `Dynamic' profiles are implemented. A default profile will always exist. This profile's name will be set to `DEFVAL' and its parameters will be set to vendor specific values, unless otherwise specified in this document. SheAdslLineConfProfileEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1 |
sheAdslLineConfProfileIndexThe table index.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.1 |
sheAdslLineConfProfileNameThis object is used by the line configuration table in order to identify a row of this table. Dynamic profiles are implemented. The profile name is user specified. Also, the system will always provide a default profile whose name is `DEFVAL' for Annex A and DEFVAL_ISDN fpr Annex B card's (both Adsl2+). Special characters are not allowed, like: space : ?ro SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.2 |
sheAdslLineConfProfileAtucConfRateModeDefines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information. fixed(1), adaptAtStartup(2), adaptAtRuntime(3)ro SheAdslLineConfRateModeType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.3 |
sheAdslLineConfProfileAtucConfRateChanRatioConfigured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and rate adaptive DSL are supported. A ratio of 20% means, that 20 % of the available data rate (in access of the minimum rate summend over all bearer channels) will be assigned to the fast channel and 80% to the interleaved channel. Only valid if sheAdslLineConfExtnProfileLineType is set to dualLatency mode.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.4 |
sheAdslLineConfProfileAtucConfTargetSnrMgnConfigured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.5 |
sheAdslLineConfProfileAtucConfMaxSnrMgnConfigured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.6 |
sheAdslLineConfProfileAtucConfMinSnrMgnConfigured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.7 |
sheAdslLineConfProfileAtucConfDownshiftSnrMgnConfigured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that adaptAtRuntime mode is not present, the value will be 'don't care'.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.8 |
sheAdslLineConfProfileAtucConfUpshiftSnrMgnConfigured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that adaptAtRuntime mode is not present, the value will be 'don't care'.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.9 |
sheAdslLineConfProfileAtucConfMinUpshiftTimeMinimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that adaptAtRuntime mode is not present, the value will be 'don't care'.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.10 |
sheAdslLineConfProfileAtucConfMinDownshiftTimeMinimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that adaptAtRuntime mode is not present, the value will be 'don't care'.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.11 |
sheAdslLineConfProfileAtucChanConfFastMinTxRateConfigured Minimum Transmit rate for `Fast' channels, in kbps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates. Only multiples of 32 will be configured.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.12 |
sheAdslLineConfProfileAtucChanConfInterleaveMinTxRateConfigured Minimum Transmit rate for `Interleave' channels, in kbps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for receive rates. Only multiples of 32 will be configured.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.13 |
sheAdslLineConfProfileAtucChanConfFastMaxTxRateConfigured Maximum Transmit rate for `Fast' channels, in kbps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for ATUC receive rates. Only multiples of 32 will be configured.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.14 |
sheAdslLineConfProfileAtucChanConfInterleaveMaxTxRateConfigured Maximum Transmit rate for `Interleave' channels, in kbps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates. Only multiples of 32 will be configured.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.15 |
sheAdslLineConfProfileAtucChanConfMaxInterleaveDelayConfigured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.16 |
sheAdslLineConfProfileAturConfRateModeDefines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information. fixed(1), adaptAtStartup(2), adaptAtRuntime(3)ro SheAdslLineConfRateModeType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.17 |
sheAdslLineConfProfileAturConfRateChanRatioConfigured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and rate adaptive DSL are supported. A ratio of 20% means, that 20 % of the available data rate (in access of the minimum rate summend over all bearer channels) will be assigned to the fast channel and 80% to the interleaved channel. Only valid if sheAdslLineConfExtnProfileLineType is set to dualLatency mode.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.18 |
sheAdslLineConfProfileAturConfTargetSnrMgnConfigured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.19 |
sheAdslLineConfProfileAturConfMaxSnrMgnConfigured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.20 |
sheAdslLineConfProfileAturConfMinSnrMgnConfigured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.21 |
sheAdslLineConfProfileAturConfDownshiftSnrMgnConfigured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that adaptAtRuntime mode is not present, the value will be 'don't care'.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.22 |
sheAdslLineConfProfileAturConfUpshiftSnrMgnConfigured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that adaptAtRuntime mode is not present, the value will be 'don't care'.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.23 |
sheAdslLineConfProfileAturConfMinUpshiftTimeMinimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that adaptAtRuntime mode is not present, the value will be 'don't care'.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.24 |
sheAdslLineConfProfileAturConfMinDownshiftTimeMinimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that adaptAtRuntime mode is not present, the value will be 'don't care'.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.25 |
sheAdslLineConfProfileAturChanConfFastMinTxRateConfigured Minimum Transmit rate for `Fast' channels, in kbps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates. Only multiples of 32 will be configured.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.26 |
sheAdslLineConfProfileAturChanConfInterleaveMinTxRateConfigured Minimum Transmit rate for `Interleave' channels, in kbps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates. Only multiples of 32 will be configured.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.27 |
sheAdslLineConfProfileAturChanConfFastMaxTxRateConfigured Maximum Transmit rate for `Fast' channels, in kbps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates. Only multiples of 32 will be configured.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.28 |
sheAdslLineConfProfileAturChanConfInterleaveMaxTxRateConfigured Maximum Transmit rate for `Interleave' channels, in kbps. See adslAturConfRateChanRatio for information regarding RADSL mode and see ATUC transmit rate for ATUR receive rates. Only multiples of 32 will be configured.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.29 |
sheAdslLineConfProfileAturChanConfMaxInterleaveDelayConfigured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.30 |
sheAdslLineConfProfileTrellisIndicates if Trelliscoding is enabled or not. If TrellisCoding is used is indicated in sheAdslLineTable and depence also on the Atur-Capabilities. The NE will not accept setting trellisOff. It is automatically controlled by firmware and will be switched off if ATU-R will not support this.ro SheAdslLineTrellisModeType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.31 |
sheAdslLineConfProfileAtucConfPwrMgmtL0TimeThis parameter represents the minimum time (in seconds) between an exit from the L2 state and the next entry into the L2 state. It ranges from 0 to 255 seconds. Only valid for Adsl2 and Adsl2Plus.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.32 |
sheAdslLineConfProfileAtucConfPwrMgmtL2TimeThis parameter represents the minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 State. It ranges from 0 to 255 seconds. Only valid for Adsl2 and Adsl2Plus.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.33 |
sheAdslLineConfProfileAtucConfPwrMgmtL2ATPRThis parameter represents the maximum aggregate transmit power reduction (in dB) that can be performed through a single Power Trim in the L2 state. It ranges from 0 dB/10 to 310 dB/10. Only valid for Adsl2 and Adsl2Plus.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.34 |
sheAdslLineConfProfileAtucConfPwrMgmtL2RateThis parameter specifies the minimum net data rate during the low power state (L2). The data rate is coded in bit/s, and can range from 0x1F40 (8000) bps to 0xFA000 (1024000) bps. Only valid for Adsl2 and Adsl2Plus.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.35 |
sheAdslLineConfProfileAtucConfPwrMgmtModeWhich ADSL Power Management state is enabled. Only valid for Adsl2 and Adsl2Plus.ro SheAdslPwrMgmtModeType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.4.1.36 |
sheAdslLineConfProfileControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5 |
sheAdslLineConfProfileControlRequestThe different Controltypes for profile creation could be used to select predefined values for the supported standard. createAdslLineConfProfile (Adsl2PlusAnnexA) createAdslLineConfProfileAnnexA createAdslLineConfProfileAnnexB createAdslLineConfProfileAdsl2PlusAnnexB createAdslLineConfProfileAdsl2AnnexI createAdslLineConfProfileAdsl2AnnexJ createAdslLineConfProfileAdsl2PlusAnnexI createAdslLineConfProfileAdsl2PlusAnnexJ createAdslLineConfProfileAdsl2AnnexM createAdslLineConfProfileAdsl2PlusAnnexM sheAdslLineConfProfileControlName ... modifyAdslLineConfProfile sheAdslLineConfProfileControlIndex sheAdslLineConfProfileControlName ... deleteAdslLineConfProfile sheAdslLineConfProfileControlIndex sheAdslLineConfProfileControlName New with R2.8: createAdslLineConfProfileAdsl2PlusDynamic sheAdslLineConfProfileControlNamerw SheAdslControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.1 |
sheAdslLineConfProfileControlIndexIndex of the configured table-entry. Needed for modify or delete.rw Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.2 |
sheAdslLineConfProfileControlStatusThe status of a user command.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.3 |
sheAdslLineConfProfileControlTimerThe maximum wait time for the manager for a long running user command.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.4 |
sheAdslLineConfProfileControlReqResultThe result of the last user command.ro SheAdslControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.5 |
sheAdslLineConfProfileControlTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.6 |
sheAdslLineConfProfileControlNameDescriptional name.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.7 |
sheAdslLineConfProfileControlAtucConfRateModeDefines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information.rw SheAdslLineConfRateModeType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.8 |
sheAdslLineConfProfileControlAtucConfRateChanRatioConfigured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and rate adaptive DSL are supported. A ratio of 20% means, that 20 % of the available data rate (in access of the minimum rate summend over all bearer channels) will be assigned to the fast channel and 80% to the interleaved channel. Only valid if sheAdslLineConfExtnProfileLineType is set to dualLatency mode.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.9 |
sheAdslLineConfProfileControlAtucConfTargetSnrMgnConfigured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.10 |
sheAdslLineConfProfileControlAtucConfMaxSnrMgnConfigured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.11 |
sheAdslLineConfProfileControlAtucConfMinSnrMgnConfigured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.12 |
sheAdslLineConfProfileControlAtucConfDownshiftSnrMgnConfigured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.13 |
sheAdslLineConfProfileControlAtucConfUpshiftSnrMgnConfigured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.14 |
sheAdslLineConfProfileControlAtucConfMinUpshiftTimeMinimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the value will be `0'.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.15 |
sheAdslLineConfProfileControlAtucConfMinDownshiftTimeMinimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL mode is not present, the value will be `0'.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.16 |
sheAdslLineConfProfileControlAtucChanConfFastMinTxRateConfigured Minimum Transmit rate for `Fast' channels, in kbps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates. Only multiples of 32 will be configured.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.17 |
sheAdslLineConfProfileControlAtucChanConfInterleaveMinTxRateConfigured Minimum Transmit rate for `Interleave' channels, in kbps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for receive rates. Only multiples of 32 will be configured.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.18 |
sheAdslLineConfProfileControlAtucChanConfFastMaxTxRateConfigured Maximum Transmit rate for `Fast' channels, in kbps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for ATUC receive rates. Only multiples of 32 will be configured.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.19 |
sheAdslLineConfProfileControlAtucChanConfInterleaveMaxTxRateConfigured Maximum Transmit rate for `Interleave' channels, in kbps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates. Only multiples of 32 will be configured.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.20 |
sheAdslLineConfProfileControlAtucChanConfMaxInterleaveDelayConfigured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.21 |
sheAdslLineConfProfileControlAturConfRateModeDefines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information.rw SheAdslLineConfRateModeType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.22 |
sheAdslLineConfProfileControlAturConfRateChanRatioConfigured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and rate adaptive DSL are supported. A ratio of 20% means, that 20 % of the available data rate (in access of the minimum rate summend over all bearer channels) will be assigned to the fast channel and 80% to the interleaved channel. Only valid if sheAdslLineConfExtnProfileLineType is set to dualLatency mode.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.23 |
sheAdslLineConfProfileControlAturConfTargetSnrMgnConfigured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.24 |
sheAdslLineConfProfileControlAturConfMaxSnrMgnConfigured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.25 |
sheAdslLineConfProfileControlAturConfMinSnrMgnConfigured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.26 |
sheAdslLineConfProfileControlAturConfDownshiftSnrMgnConfigured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.27 |
sheAdslLineConfProfileControlAturConfUpshiftSnrMgnConfigured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.28 |
sheAdslLineConfProfileControlAturConfMinUpshiftTimeMinimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the value will be `0'.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.29 |
sheAdslLineConfProfileControlAturConfMinDownshiftTimeMinimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL mode is not present, the value will be `0'.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.30 |
sheAdslLineConfProfileControlAturChanConfFastMinTxRateConfigured Minimum Transmit rate for `Fast' channels, in kbps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates. Only multiples of 32 will be configured.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.31 |
sheAdslLineConfProfileControlAturChanConfInterleaveMinTxRateConfigured Minimum Transmit rate for `Interleave' channels, in kbps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates. Only multiples of 32 will be configured.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.32 |
sheAdslLineConfProfileControlAturChanConfFastMaxTxRateConfigured Maximum Transmit rate for `Fast' channels, in kbps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates. Only multiples of 32 will be configured.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.33 |
sheAdslLineConfProfileControlAturChanConfInterleaveMaxTxRateConfigured Maximum Transmit rate for `Interleave' channels, in kbps. See adslAturConfRateChanRatio for information regarding RADSL mode and see ATUC transmit rate for ATUR receive rates. Only multiples of 32 will be configured.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.34 |
sheAdslLineConfProfileControlAturChanConfMaxInterleaveDelayConfigured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.35 |
sheAdslLineConfProfileControlTrellisIndicates if Trelliscoding is enabled or not. If TrellisCoding is used is indicated in sheAdslLineTable and depence also on the Atur-Capabilities. Do not touch!rw SheAdslLineTrellisModeType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.36 |
sheAdslLineConfProfileControlAtucConfPwrMgmtL0TimeThis parameter represents the minimum time (in seconds) between an exit from the L2 state and the next entry into the L2 state. It ranges from 0 to 255 seconds. Only valid for Adsl2 and Adsl2Plus.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.37 |
sheAdslLineConfProfileControlAtucConfPwrMgmtL2TimeThis parameter represents the minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 State. It ranges from 0 to 255 seconds. Only valid for Adsl2 and Adsl2Plus.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.38 |
sheAdslLineConfProfileControlAtucConfPwrMgmtL2ATPRThis parameter represents the maximum aggregate transmit power reduction (in dB) that can be performed through a single Power Trim in the L2 state. It ranges from 0 dB/10 to 310 dB/10. Only valid for Adsl2 and Adsl2Plus.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.39 |
sheAdslLineConfProfileControlAtucConfPwrMgmtL2RateThis parameter specifies the minimum net data rate during the low power state (L2). The data rate is coded in bit/s, and can range from 0x1F40 (8000) bps to 0xFA000 (1024000) bps. Only valid for Adsl2 and Adsl2Plus.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.40 |
sheAdslLineConfProfileControlAtucConfPwrMgmtModeWhich ADSL Power Management state is enabled. Only valid for Adsl2 and Adsl2Plus.rw SheAdslPwrMgmtModeType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.5.41 |
sheAdslLineConfExtnProfileTableThis table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the ADSL line. SEQUENCE OF SheAdslLineConfExtnProfileEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6 |
sheAdslLineConfExtnProfileEntryEach entry consists of a list of parameters that represents the configuration of an ADSL modem. The index is used from the sheAdslLineConfProfileTable. SheAdslLineConfExtnProfileEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1 |
sheAdslLineConfExtnProfileParametricTestInputFileIndicates Name of the Input file from which to take the Mask Array Size, lower and upper mask Array. Null string means no file is specified. Functionality is not supported!ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.1 |
sheAdslLineConfExtnProfileRsIntCorrectionUpSets the correction time for the upstream-interleaved buffer. RS can also be disabled. The Default Value for ADSL+ is 3. value125us(3), value250us(4), value500us(5), value1ms(6), value2ms(7), value4ms(8), disable(15)ro SheAdslLineConfRsIntCorrectionType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.2 |
sheAdslLineConfExtnProfileLineTypeThis parameter provisions the DSL physical entity at start-up by defining whether and how the line will be channelized, i.e. which channel type(s) are supported. Defined values are: fastOnly(2) -- only fast channel exists (singleLatency) interleavedOnly(3) -- only interleaved channel exists (singleLatency, default) fastAndInterleaved(5) -- both fast and interleaved channels (dualLatency) exist In case of dualLatency (mode 5), the parameter's sheAdslLineConfProfileAtucConfRateChanRatio and sheAdslLineConfProfileAturConfRateChanRatio configures the bandwith distribution. IMPORTANT NOTE: The configuration of dualLatency mode is only available for NE releases up R2.5!! The modification is only possible for profiles, which are NOT IN USE!ro SheAdslConfLineType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.3 |
sheAdslLineConfExtnProfileTxEndBinHighest bin number allowed for Tx signal. The Range & default for ADSL+ is 0x06 - 0x1ff respectively. NE will not accept any changes and use always default value! Ne will select the correct values depending on the configuration of the following values: - AnnexType - DmtConfMode - AdvertisedCapability New with R2.8: If the used annexType was set to 'dynamic', no values of Tx/Rx bins could be set here, because this will be done by the IU depending on the used HW and choosen standard. The profile configuration will be set to value 65535 (0xffff) which means 'autoSelect'.ro INTEGER (6..511 | 65535) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.4 |
sheAdslLineConfExtnProfileTxStartBinLowest bin number allowed for Tx signal.The Range for ADSL+ is 0x06 - 0x1ff. The Default for Annex B is 58 respectively. For AnnexA it is 32. NE will not accept any changes and use always default value! Ne will select the correct values depending on the configuration of the following values: - AnnexType - DmtConfMode - AdvertisedCapability New with R2.8: If the used annexType was set to 'dynamic', no values of Tx/Rx bins could be set here, because this will be done by the IU depending on the used HW and choosen standard. The profile configuration will be set to value 65535 (0xffff) which means 'autoSelect'.ro INTEGER (6..511 | 65535) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.5 |
sheAdslLineConfExtnProfileMaxBitsPerBinMaximum Rx number of bits per bin. NE will not accept any changes and use always default value!ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.6 |
sheAdslLineConfExtnProfileRxStartBinLowest bin number allowed for Rx signal. Default value for AnnexA is 6 and 32 for AnnexB. NE will not accept any changes and use always default value! Ne will select the correct values depending on the configuration of the following values: - AnnexType - DmtConfMode - AdvertisedCapability New with R2.8: If the used annexType was set to 'dynamic', no values of Tx/Rx bins could be set here, because this will be done by the IU depending on the used HW and choosen standard. The profile configuration will be set to value 65535 (0xffff) which means 'autoSelect'.ro INTEGER (1..57 | 65535) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.7 |
sheAdslLineConfExtnProfileRxEndBinHighest bin number allowed for Rx signal. Default Value for AnnexA is 31 and 57 for AnnexB. NE will not accept any changes and use always default value! Ne will select the correct values depending on the configuration of the following values: - AnnexType - DmtConfMode - AdvertisedCapability New with R2.8: If the used annexType was set to 'dynamic', no values of Tx/Rx bins could be set here, because this will be done by the IU depending on the used HW and choosen standard. The profile configuration will be set to value 65535 (0xffff) which means 'autoSelect'.ro INTEGER (6..64 | 65535) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.8 |
sheAdslLineConfExtnProfileRxBinAdjustEmploys Rx Start/End bin settings. NE will not accept any changes and use always default value!ro SheAdslLineConfExtnProfileRxBinAdjustType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.9 |
sheAdslLineConfExtnProfileTriggerModeIndicates the Type of event that triggers fast retrain. disable(0), locCrc(1), rmtCrc(2), snrInc(4), snrDec(8) NE will not accept any changes and use always default value!ro SheAdslLineConfTriggerModeType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.10 |
sheAdslLineConfExtnProfileAdi2xFor non standard compliant ADI CPE. NE will not accept any changes and use always default value!ro SheAdslLineConfExtnProfileAdi2xType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.11 |
sheAdslLineConfExtnProfileStandardPreferred standard compliance. Outcome is dependent upon standard support of the remote unit.GlobespanVirata High Speed ADSL DMT (ADSL+) applications only. t1413(0), gLite(1), gDmt(2), multiMode(4), adsl2(26), adsl2_plus(27), readsl2(28), adsl2_auto(29), adsl2_plus_auto(30), adsl2adsl2PlusOnly(31) New with R2.8: If the used annexType was set to 'dynamic', the standardTypes 't1413', 'gLite', 'gDmt' and 'readsl2' could NOT be used. 'adsl2_plus_auto' should be the prefered use in that case!ro SheAdslLineConfStandardType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.12 |
sheAdslLineConfExtnProfileInitiateSpecifies which end initiates startup. It is also used to send a C-tone to the remote unit. waitPn(0), ctone(1), initiatePn(128) NE will not accept any changes and use always default value!ro SheAdslLineConfInitiateType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.13 |
sheAdslLineConfExtnProfileTxPowerAttenuationSpecifies value of Tx power attenuation. value0(0)...value21(21)ro SheAdslLineConfAttenuationType UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.14 |
sheAdslLineConfExtnProfileCodingGainSets the coding gain in dB increments. gain0(0), gain1(4096), gain2(8192), gain3(12288), gain4(16384), gain5(20480), gain6(24576), gain7(28672), auto(65280) NE will not accept any changes and use always default value!ro SheAdslLineConfGainType UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.15 |
sheAdslLineConfExtnProfileRsFastOvrhdDownSets the percentage overhead for the downstream-fast buffer. ovrHd50(1), ovrHd25(2), ovrHd12(3), ovrHd6(4), ovrHd3(5), ovrHd1(7), disable(15) NE will not accept any changes and use always default value!ro SheAdslLineConfRsFastOvrhdType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.16 |
sheAdslLineConfExtnProfileIntCorrectionDownThis parameter sets the correction time for the downstream interleaved buffer. RS can also be disabled. value125us(3), value250us(4), value500us(5), value1ms(6), value2ms(7), value4ms(8), disable(15)ro SheAdslLineConfRsIntCorrectionType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.17 |
sheAdslLineConfExtnProfileRsFastOvrhdUpSets the percentage overhead for the upstream-fast buffer. ovrHd50(1), ovrHd25(2), ovrHd12(3), ovrHd6(4), ovrHd3(5), ovrHd1(7), disable(15) NE will not accept any changes and use always default value!ro SheAdslLineConfRsFastOvrhdType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.18 |
sheAdslLineConfExtnProfileDrStbyProvides the ability to disable power to the line driver. disable(0), enable(1) NE will not accept any changes and use always default value!ro SheAdslLineConfEnableType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.19 |
sheAdslLineConfExtnProfileExpandedExchangeThis object is used to Enable/Disable EES. disable(0), enable(1) NE will not accept any changes and use always default value!ro SheAdslLineConfExpandedExchangeType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.20 |
sheAdslLineConfExtnProfileEscapeFastRetrainEnableThis object is used to Enable/ Disable escape to the fast retrain capability. disable(0), enable(1) NE will not accept any changes and use always default value!ro SheAdslLineConfEnableType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.21 |
sheAdslLineConfExtnProfileFastRetrainEnableThis object is used to Enable/ Disable the fast retrain capability. disable(32768), enable(0) NE will not accept any changes and use always default value!ro SheAdslLineConfEnableSpecial3Type .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.22 |
sheAdslLineConfExtnProfileBitSwapThis object is used to Enable/Disable bit swapping. enable(32768), disable(0)ro SheAdslLineConfEnableSpecial2Type .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.23 |
sheAdslLineConfExtnProfileNtrThis object is used to Enable/ Disable NTR on a per chip basis.ro SheAdslLineConfNtrType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.24 |
sheAdslLineConfExtnProfileAnnexTypeThis parameter is set as per annex compliance of the code release. GlobespanVirata High Speed ADSL DMT (ADSL+) applications only. annexA(0), annexB(1), highSpeed(2), annexAdsl2(5), annexI(10), annexJ(11), annexM(12) New with R2.8: dynamic(50) If the used annexType was set to 'dynamic', such a profile could be assigned to any type of supported ADSL IU. The IU will select the supported annex himself, depending on HW restrictions and line parameters. This selection made additional restrictions to the following parameters: - tx/rx start and end bin usage - profile Standard - profile AdvertisedCapabilities - profileLineDmtConfModero SheAdslLineConfAnnexType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.25 |
sheAdslLineConfExtnProfileAlctlUsVerThis object is used for T1.413 demo purposes only. NE will not accept any changes and use always default value!ro SheAdslLineConfExtnProfileAlctlUsVerType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.26 |
sheAdslLineConfExtnProfileUseCustomBinThis object is used to Enable/ Disable user selection of bin-usage defined in sheAdslLineConfExtnProfileDnBinUsage. disable(0), enable(32768)ro SheAdslLineConfEnableSpecial2Type .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.27 |
sheAdslLineConfExtnProfileDnBinUsageThe parameter where a 1 in bit position indicates usage of corresponding bin, whereas a 0 disables usage of corresponding bin.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.28 |
sheAdslLineConfExtnProfileMaxDCoThis object is used to indicate Maximum interleaving depth supported by the customer's hardware. value64(0), value128(4096), value256(8192)ro SheAdslLineConfIntDephtType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.29 |
sheAdslLineConfExtnProfileFullRetrainThis object is used to Indicate enable/disable of auto retrain capability. enable(0), disable(32768) NE will not accept any changes and use always default value!ro SheAdslLineConfEnableSpecial3Type .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.30 |
sheAdslLineConfExtnProfileAdvertisedCapabilitiesControls if the CO will attempt to startup using alternate standards if the CPE does not support ADSL+. New with R2.8: If the used annexType was set to 'dynamic', this parameter should be set to 'disabled' or 'adslPlus'. All other values will not work with the intended set of dynamic annexType selection by IU.ro SheAdslLineConfAdvertisedCapabilitiesType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.31 |
sheAdslLineConfExtnProfilePsdMaskTypeSelects the PSD mask option to be used.ro SheAdslLineConfPsdMaskType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.32 |
sheAdslLineConfExtnProfileLineDmtConfModeSelects if there is overlap or no overlap of bins. Overlapping is only supported by non ISDN profiles and will change the setting for TxStartBin accordingly!!. New with R2.8: If the used annexType was set to 'dynamic', this parameter should be set to 'fdmMode' only. Other values will not work with the intended set of dynamic annexType selection by IU.ro SheAdslLineConfLineDmtConfModeType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.33 |
sheAdslLineConfExtnProfileEraseProfilesEnables/Disables the ability to erase all fast retrain profiles at startup. disable(0), enable(32768)ro SheAdslLineConfEnableSpecial2Type .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.34 |
sheAdslLineConfExtnProfileRsMemoryIndicates whether customer's Hardware should use external RS RAM. Could not be configured and depends only on the used card type.ro SheAdslLineConfRsMemoryType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.35 |
sheAdslLineConfExtnProfileParamHybridLossTestStartIndicates Start bin for range of bins to be measured.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.36 |
sheAdslLineConfExtnProfileParamHybridLossTestEndIndicates End bin for range of bins to be measured.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.37 |
sheAdslLineConfExtnProfileConfMinInpNew ADSL2+ parameter. The user configures the duration of impulse noise the system should withstand. This parameter configures the value for downstream direction.ro SheAdslConfMinInpType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.38 |
sheAdslLineConfExtnProfileRfiBandMaskBitMask for sheAdslRfiBandIndex. Configured RFI bands are used for this profile.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.39 |
sheAdslLineConfExtnProfileUpstreamPsdMaskSelectionSelects the PSD mask option to be used. This parameter is used only for annexes J and M of ITU-T Recs. G.992-3 and G.992.5 Other profiles will ignore the configured value and use per default the value noSelection(0).ro SheAdslLineConfUpstreamPSDMaskSelectionType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.40 |
sheAdslLineConfExtnProfileMaxNomPsdDsThe maximum nominal transmit PSD in the downstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz. (physical values are -60 to -30 dBm/Hz).ro INTEGER (-600..-300) UNITS "0.1 dBm/Hz" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.41 |
sheAdslLineConfExtnProfileMaxNomAtpDsThe maximum nominal aggregate transmit power in the downstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm).ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.42 |
sheAdslLineConfExtnProfilePsdMaskDsThe downstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G.992.5 and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). But the range of start-bin and end-bin is in range 0 to 195 (0 to -97.5dBm/Hz). Two break points (6 byte) are reserved for start sub-carrier index and end sub-carrier index. So the range of size is 6 up to 96. When the number of breakpoints is less than 32, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.43 |
sheAdslLineConfExtnProfilePSDMASKdsEnableUser custom PSD mask-related parameter used by the ATU-C to use user custom PSD mask. (Not available for ADSL but ADSL2 and ADSL2plus ).ro SheAdslLineConfEnableType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.44 |
sheAdslLineConfExtnProfileConfMinInpUsNew ADSL2+ parameter. The user configures the duration of impulse noise the system should withstand. This parameter configures the value for upstream direction.ro SheAdslConfMinInpType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.6.1.45 |
sheAdslLineConfExtnProfileControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7 |
sheAdslLineConfExtnProfileControlRequestmodifyAdslLineConfExtnProfile sheAdslLineConfExtnProfileControlIndex sheAdslLineConfExtnProfileControlName ...rw SheAdslControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.1 |
sheAdslLineConfExtnProfileControlIndexIndex of the table entry to be configured. Needed for modify.rw Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.2 |
sheAdslLineConfExtnProfileControlStatusThe status of a user command.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.3 |
sheAdslLineConfExtnProfileControlTimerThe maximum wait time for the manager for a long running user command.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.4 |
sheAdslLineConfExtnProfileControlReqResultThe result of the last user command.ro SheAdslControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.5 |
sheAdslLineConfExtnProfileControlTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.6 |
sheAdslLineConfExtnProfileControlNameDescriptional name. The name used during configuration of this profile is equal to the name of the sheAdslLineConfProfile with the identical index.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.7 |
sheAdslLineConfExtnProfileControlParametricTestInputFileIndicates Name of the Input file from which to take the Mask Array Size, lower and upper mask Array. Null string means no file is specified.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.8 |
sheAdslLineConfExtnProfileControlRsIntCorrectionUpSets the correction time for the upstream-interleaved buffer. RS can also be disabled. The Default Value for ADSL+ is 3.rw SheAdslLineConfRsIntCorrectionType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.9 |
sheAdslLineConfExtnProfileControlLineTypeThis parameter provisions the DSL physical entity at start-up by defining whether and how the line will be channelized, i.e. which channel type(s) are supported. Defined values are: fastOnly(2) -- only fast channel exists (singleLatency) interleavedOnly(3) -- only interleaved channel exists (singleLatency, default) fastAndInterleaved(5) -- both fast and interleaved channels (dualLatency) exist In case of dualLatency (mode 5), the parameter's sheAdslLineConfProfileAtucConfRateChanRatio and sheAdslLineConfProfileAturConfRateChanRatio configures the bandwith distribution. IMPORTANT NOTE: The configuration of dualLatency mode is only available for NE releases up R2.5!! The modification is only possible for profiles, which are NOT IN USE!rw SheAdslConfLineType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.10 |
sheAdslLineConfExtnProfileControlTxEndBinHighest bin number allowed for Tx signal. The Range & default for ADSL+ is 0x06 - 0x1ff respectively. NE will not accept any changes and use always default value! Ne will select the correct values depending on the configuration of the following values: - AnnexType - DmtConfMode - AdvertisedCapabilityrw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.11 |
sheAdslLineConfExtnProfileControlTxStartBinLowest bin number allowed for Tx signal.The Range for ADSL+ is 0x06 - 0x1ff. NE will not accept any changes and use always default value! Ne will select the correct values depending on the configuration of the following values: - AnnexType - DmtConfMode - AdvertisedCapabilityrw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.12 |
sheAdslLineConfExtnProfileControlMaxBitsPerBinMaximum Rx number of bits per bin. NE will not accept any changes and use always default value!rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.13 |
sheAdslLineConfExtnProfileControlRxStartBinLowest bin number allowed for Rx signal. NE will not accept any changes and use always default value! Ne will select the correct values depending on the configuration of the following values: - AnnexType - DmtConfMode - AdvertisedCapabilityrw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.14 |
sheAdslLineConfExtnProfileControlRxEndBinHighest bin number allowed for Rx signal. NE will not accept any changes and use always default value! Ne will select the correct values depending on the configuration of the following values: - AnnexType - DmtConfMode - AdvertisedCapabilityrw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.15 |
sheAdslLineConfExtnProfileControlRxBinAdjustEmploys Rx Start/End bin settings. NE will not accept any changes and use always default value!rw SheAdslLineConfExtnProfileRxBinAdjustType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.16 |
sheAdslLineConfExtnProfileControlTriggerModeIndicates the Type of event that triggers fast retrain. NE will not accept any changes and use always default value!rw SheAdslLineConfTriggerModeType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.17 |
sheAdslLineConfExtnProfileControlAdi2xFor non standard compliant ADI CPE. NE will not accept any changes and use always default value!rw SheAdslLineConfExtnProfileAdi2xType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.18 |
sheAdslLineConfExtnProfileControlStandardPreferred standard compliance. Outcome is dependent upon standard support of the remote unit.GlobespanVirata High Speed ADSL DMT (ADSL+) applications only. New with R2.8: If the used annexType was set to 'dynamic', the standardTypes 't1413', 'gLite', 'gDmt' and 'readsl2' could NOT be used. 'adsl2_plus_auto' should be the prefered use in that case!rw SheAdslLineConfStandardType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.19 |
sheAdslLineConfExtnProfileControlInitiateSpecifies which end initiates startup. It is also used to send a C-tone to the remote unit. NE will not accept any changes and use always default value!rw SheAdslLineConfInitiateType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.20 |
sheAdslLineConfExtnProfileControlTxPowerAttenuationSpecifies value of Tx power attenuation.rw SheAdslLineConfAttenuationType UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.21 |
sheAdslLineConfExtnProfileControlCodingGainSets the coding gain in dB increments. NE will not accept any changes and use always default value!rw SheAdslLineConfGainType UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.22 |
sheAdslLineConfExtnProfileControlRsFastOvrhdDownSets the percentage overhead for the downstream-fast buffer. NE will not accept any changes and use always default value!rw SheAdslLineConfRsFastOvrhdType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.23 |
sheAdslLineConfExtnProfileControlIntCorrectionDownThis parameter sets the correction time for the downstream interleaved buffer.RS can also be disabled.rw SheAdslLineConfRsIntCorrectionType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.24 |
sheAdslLineConfExtnProfileControlRsFastOvrhdUpSets the percentage overhead for the upstream-fast buffer. NE will not accept any changes and use always default value!rw SheAdslLineConfRsFastOvrhdType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.25 |
sheAdslLineConfExtnProfileControlDrStbyProvides the ability to disable power to the line driver. NE will not accept any changes and use always default value!rw SheAdslLineConfEnableType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.26 |
sheAdslLineConfExtnProfileControlExpandedExchangeThis object is used to Enable/Disable EES. NE will not accept any changes and use always default value!rw SheAdslLineConfExpandedExchangeType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.27 |
sheAdslLineConfExtnProfileControlEscapeFastRetrainEnableThis object is used to Enable/ Disable escape to the fast retrain capability. NE will not accept any changes and use always default value!rw SheAdslLineConfEnableType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.28 |
sheAdslLineConfExtnProfileControlFastRetrainEnableThis object is used to Enable/ Disable the fast retrain capability. NE will not accept any changes and use always default value!rw SheAdslLineConfEnableSpecial3Type .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.29 |
sheAdslLineConfExtnProfileControlBitSwapThis object is used to Enable/Disable bit swapping.rw SheAdslLineConfEnableSpecial2Type .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.30 |
sheAdslLineConfExtnProfileControlNtrThis object is used to Enable/ Disable NTR on a per chip basis.rw SheAdslLineConfNtrType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.31 |
sheAdslLineConfExtnProfileControlAnnexTypeThis parameter is set as per annex compliance of the code release. GlobespanVirata High Speed ADSL DMT (ADSL+) applications only. New with R2.8: dynamic(50) If the used annexType was set to 'dynamic', such a profile could be assigned to any type of supported ADSL IU. The IU will select the supported annex himself, depending on HW restrictions and line parameters. This selection made additional restrictions to the following parameters: - tx/rx start and end bin usage - profile Standard - profile AdvertisedCapabilities - profileLineDmtConfModerw SheAdslLineConfAnnexType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.32 |
sheAdslLineConfExtnProfileControlAlctlUsVerThis object is used for T1.413 demo purposes only. NE will not accept any changes and use always default value!rw SheAdslLineConfExtnProfileAlctlUsVerType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.33 |
sheAdslLineConfExtnProfileControlUseCustomBinThis object is used to Enable/ Disable user selection on which of the 256 bins will be enabled for downstream transmission.rw SheAdslLineConfEnableSpecial2Type .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.34 |
sheAdslLineConfExtnProfileControlDnBinUsageThe parameter where a 1 in bit position indicates usage of corresponding bin,whereas a 0 disables usage of corresponding bin.rw OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.35 |
sheAdslLineConfExtnProfileControlMaxDCoThis object is used to indicate Maximum interleaving depth supported by the customer's hardware.rw SheAdslLineConfIntDephtType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.36 |
sheAdslLineConfExtnProfileControlFullRetrainThis object is used to Indicate enable/disable of auto retrain capability. NE will not accept any changes and use always default value!rw SheAdslLineConfEnableSpecial3Type .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.37 |
sheAdslLineConfExtnProfileControlAdvertisedCapabilitiesControls if the CO will attempt to startup using alternate standards if the CPE does not support ADSL+. New with R2.8: If the used annexType was set to 'dynamic', this parameter should be set to 'disabled' or 'adslPlus'. All other values will not work with the intended set of dynamic annexType selection by IU.rw SheAdslLineConfAdvertisedCapabilitiesType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.38 |
sheAdslLineConfExtnProfileControlPsdMaskTypeSelects the PSD mask option to be used.rw SheAdslLineConfPsdMaskType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.39 |
sheAdslLineConfExtnProfileControlLineDmtConfModeSelects if there is overlap or no overlap of bins. Overlapping is only supported by non ISDN profiles and will change the setting for TxStartBin accordingly!!. New with R2.8: If the used annexType was set to 'dynamic', this parameter should be set to 'fdmMode' only. Other values will not work with the intended set of dynamic annexType selection by IU.rw SheAdslLineConfLineDmtConfModeType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.40 |
sheAdslLineConfExtnProfileControlEraseProfilesEnables/Disables the ability to erase all fast retrain profiles at startup.rw SheAdslLineConfEnableSpecial2Type .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.41 |
sheAdslLineConfExtnProfileControlParamHybridLossTestStartIndicates Start bin for range of bins to be measured.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.43 |
sheAdslLineConfExtnProfileControlParamHybridLossTestEndIndicates End bin for range of bins to be measured.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.44 |
sheAdslLineConfExtnProfileControlConfMinInpLook at table.rw SheAdslConfMinInpType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.45 |
sheAdslLineConfExtnProfileControlRfiBandMaskBitMask for sheAdslRfiBandIndex in sheAdslRfiBandTable.rw OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.46 |
sheAdslLineConfExtnProfileControlUpstreamPsdMaskSelectionThis configuration parameter defines which upstream PSD mask is enabled. This parameter is used only for annexes J and M of ITU-T Recs. G.992-3 and G.992.5rw SheAdslLineConfUpstreamPSDMaskSelectionType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.47 |
sheAdslLineConfExtnProfileControlMaxNomPsdDsThe maximum nominal transmit PSD in the downstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz. (physical values are -60 to -30 dBm/Hz).rw INTEGER (-600..-300) UNITS "0.1 dBm/Hz" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.48 |
sheAdslLineConfExtnProfileControlMaxNomAtpDsThe maximum nominal aggregate transmit power in the downstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm).rw Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.49 |
sheAdslLineConfExtnProfileControlPsdMaskDsThe downstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G.992.5 and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). But the range of start-bin and end-bin is in range 0 to 195 (0 to -97.5dBm/Hz). Two break points (6 byte) are reserved for start sub-carrier index and end sub-carrier index. So the range of size is 6 up to 96. When the number of breakpoints is less than 32, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.rw OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.50 |
sheAdslLineConfExtnProfileControlPSDMASKdsEnableUser custom PSD mask-related parameter used by the ATU-C to use user custom PSD mask. (Not available for ADSL but ADSL2 and ADSL2plus ).rw SheAdslLineConfEnableType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.51 |
sheAdslLineConfExtnProfileControlPSDMASKdsRequestResultThe result of the last psd commmandro SheAdslControlPSDMASKdsRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.52 |
sheAdslLineConfExtnProfileControlConfMinInpUsLook at table.rw SheAdslConfMinInpType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.7.53 |
sheAdslLineTableThis table includes common attributes describing both ends of the line. It is required for all ADSL physical interfaces. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94). SEQUENCE OF SheAdslLineEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8 |
sheAdslLineEntryAn entry in adslLineTable. SheAdslLineEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1 |
sheAdslLineCodingSpecifies the ADSL coding type used on this line.ro AdslLineCodingType (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1.1 |
sheAdslLineTypeShows the type of ADSL physical line entity that exists, by defining whether and how the line is channelized. If the line is channelized, the value will be other than noChannel(1). This object shows which channel type(s) are currently supported. This values are possible: no channels exist (maybe line is not accessible) fast channel exists only (singleLatency) interleaved channel exists only (singleLatency) fast and interleaved channel exist (dualLatency)ro SheAdslConfLineType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1.2 |
sheAdslLineSpecificOID instance in vendor-specific MIB. The Instance may be used to determine shelf/slot/port of the ATUC interface in a DSLAM.ro VariablePointer (SNMPv2-TC) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1.3 |
sheAdslLineConfProfileThe value of this object identifies the row in the ADSL Line Configuration Profile Table, which applies for this ADSL line, and channels if applicable. A 'DEFVAL' profile will always be exist and set per default.ro SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1.4 |
sheAdslLineAlarmConfProfileThe value of this object identifies the row in the ADSL Line Alarm Configuration Profile Table, which applies to this ADSL line, and channels if applicable. A 'DEFAULT' profile will always be exist and set.ro SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1.6 |
sheAdslLineActionThis object indicates parameter that allows actions on a per line basis. These actions include abort, startup, and tests.ro SheAdslLineActionType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1.7 |
sheAdslLineLineDmtTrellisParameter that indicates whether trellis coding has been enabled or disabled. Trellis coding should always be enabled for its clear performance advantage. trellisOn(1), trellisOff(2)ro SheAdslLineTrellisModeType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1.8 |
sheAdslLineUtopiaL2RxAddrThis object indicates UTOPIA Level 2 Rx address for a line.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1.9 |
sheAdslLineUtopiaL2TxAddrThis object indicates UTOPIA Level 2 Tx address for a line.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1.10 |
sheAdslLineClockTypeThis object indicates parameter to set use of either crystal or oscillator.ro SheAdslLineClockType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1.12 |
sheAdslLineAtucCapabilityThe capability of co-side. Be aware that multiple bits could be set! Each bit set to 1 means, that the corresponding standart is supported.ro SheAdslAtuxCapabilityType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1.13 |
sheAdslLineAturCapabilityThe capability of remote-side. Only available if line has trained - otherwise 0. Be aware that multiple bits could be set! Each bit set to 1 means, that the corresponding standart is supported.ro SheAdslAtuxCapabilityType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1.14 |
sheAdslLineAtuActualCapabilityThe actual used capability of the line. Only available if line has trained - otherwise 0. Each bit set to 1 means, that the corresponding standart is supported.ro SheAdslAtuxCapabilityType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1.15 |
sheAdslLinePwrMgmtPMSFThis object indicates the action that forces a change in the line state of power management. (Not available for ADSL G992.1) Valid values: pmsfL0ToL2StateForce(1) -> testmode, set running line to L2 power safe mode pmsfL2ToL0StateForce(3) -> switch back line from L2 power safe mode to full power L0 state The transitions pmsfL3ToL0StateForce (unlock) and pmsfL3StateForce (lock) should always be done via ifAdminState setting.ro SheAdslPwrMgmtPMSFType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1.16 |
sheAdslLineDeltConfLDSFDELT-related parameter used by the ATU-C to force the line into loop diagnostics mode. (Not available for ADSL but ADSL2 and ADSL2plus ).ro SheAdslLineDeltConfLDSFType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1.17 |
sheAdslLineRfiBandMaskBitMask for used sheAdslRfiBandIndex. A Bit-Position correspond's with an index in sheAdslRfiBandTable and mark configured RFI bands they are used for this profile.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1.18 |
sheAdslLineDpboProfileThe value of this object identifies the row in the AdslLineDpboProfile Table, which applies for this ADSL line. No 'DEFVAL' profile will exist. Per default no profile is assigned!ro SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.8.1.19 |
sheAdslLineControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.9 |
sheAdslLineControlRequestmodifyAdslLineEntry: sheAdslLineControlIndex sheAdslLineControlConfProfile sheAdslLineControlAction modifyAdslLineAlarmConfProfileEntry: sheAdslLineControlIndex sheAdslLineControlAlarmConfProfile forceAdslLinePwrMgmtState: vheAdslLineControlIndex sheAdslLineControlPwrMgmtPMSF modifyAdslLineDeltConfEntry: sheAdslLineControlIndex sheAdslLineControlDeltConfLDSF modifyAdslLineRfiBandMask: sheAdslLineControlIndex sheAdslLineControlRfiBandMask ##New for SHR R2.6 setAdslLineDpboProfileEntry: sheAdslLineControlIndex sheAdslLineControlDpboProfilerw SheAdslControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.9.1 |
sheAdslLineControlIndexIfIndex of the configured adsl-interface.rw Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.9.2 |
sheAdslLineControlStatusThe status of a user command.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.9.3 |
sheAdslLineControlTimerThe maximum wait time for the manager for a long running user command.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.9.4 |
sheAdslLineControlReqResultThe result of the last user command.ro SheAdslControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.9.5 |
sheAdslLineControlTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.9.6 |
sheAdslLineControlConfProfileThe value of this object identifies the row in the ADSL Line Configuration Profile Table, (adslLineConfProfileTable), which applies for this ADSL line, and channels if applicable. For the used `dynamic' mode, in the case which the configuration profile has not been set, the value will be set to `DEFVAL'.rw SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.9.7 |
sheAdslLineControlAlarmConfProfileThe value of this object identifies the row in the ADSL Line Alarm Configuration Profile Table, (adslLineAlarmConfProfileTable), which applies to this ADSL line, and channels if applicable. For the used `dynamic' mode, in the case which the alarm profile has not been set, the value will be set to `DEFVAL'.rw SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.9.9 |
sheAdslLineControlActionThis object indicates parameter that allows actions on a per line basis. These actions include abort, startup, and tests.rw SheAdslLineActionType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.9.10 |
sheAdslLineControlPwrMgmtPMSFForce a change in the line state of power management. (Not available for ADSL G992.1) Valid values: pmsfL0ToL2StateForce(1) -> testmode, set running line to L2 power safe mode pmsfL2ToL0StateForce(3) -> switch back line from L2 power safe mode to full power L0 state The transitions pmsfL3ToL0StateForce (unlock) and pmsfL3StateForce (lock) should always be done via ifAdminState setting.rw SheAdslPwrMgmtPMSFType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.9.11 |
sheAdslLineControlDeltConfLDSFDELT-related parameter used by the ATU-C to force the line into loop diagnostics mode. (Not available for ADSL but ADSL2 and ADSL2plus ).rw SheAdslLineDeltConfLDSFType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.9.12 |
sheAdslLineControlRfiBandMaskBitMask for sheAdslRfiBandIndex in sheAdslRfiBandTable.rw OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.9.13 |
sheAdslLineControlDpboProfileThe value of this object identifies the row in the AdslLineDpboProfile Table, which applies for this ADSL line.rw SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.9.14 |
sheAdslAtucPhysTableThis table provides one row for each ATUC. Each row contains the Physical Layer Parameters table for that ATUC. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94). SEQUENCE OF SheAdslAtucPhysEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10 |
sheAdslAtucPhysEntryAn entry in the adslAtucPhysTable. SheAdslAtucPhysEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1 |
sheAdslAtucPhysInvSerialNumberThe vendor specific string that identifies the vendor equipment.ro SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.1 |
sheAdslAtucPhysInvVendorIDThe vendor ID code is a copy of the binary vendor identification field defined by the PHY[10] and expressed as readable characters.ro SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.2 |
sheAdslAtucPhysInvVersionNumberThe vendor specific version number sent by this ATU as part of the initialization messages. It is a copy of the binary version number field defined by the PHY[10] and expressed as readable characters.ro SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.3 |
sheAdslAtucPhysCurrSnrMgnNoise Margin as seen by this ATU with respect to its received signal in tenth dB.ro INTEGER (-640..640) UNITS "tenth dB" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.4 |
sheAdslAtucPhysCurrAtnMeasured difference in the total power transmitted by the peer ATU and the total power received by this ATU.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.5 |
sheAdslAtucPhysCurrStatusIndicates current state of the ATUC line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUC failure due to not receiving valid frame. 2 lossOfSignal ATUC failure due to not receiving signal. 3 lossOfPower ATUC failure due to loss of power. Note: the Agent may still function. 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. 5 lossOfLink ATUC failure due to inability to link with ATUR. 6 dataInitFailure ATUC failure during initialization due to bit errors corrupting startup exchange data. 7 configInitFailure ATUC failure during initialization due to peer ATU not able to support requested configuration 8 protocolInitFailure ATUC failure during initialization due to incompatible protocol used by the peer ATU. 9 noPeerAtuPresent ATUC failure during initialization due to no activation sequence detected from peer ATU. This is intended to supplement ifOperStatus.ro SheAdslLineCurrentStatusType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.6 |
sheAdslAtucPhysCurrOutputPwrMeasured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence.ro INTEGER (-310..310) UNITS "tenth dBm" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.7 |
sheAdslAtucPhysCurrAttainableRateIndicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate.ro Gauge32 UNITS "kbps" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.8 |
sheAdslAtucPhysOpStateThis object indicates the operational state of the ATU. Values include idle,handshake, training, Delt mode (loop diagnostic mode), etc. idle(0), data(1), bootUpLoad(8), handshake(16), training(24), framerSync(26), fastRetrainInProg(27), llTest(128), dlTest(131), txTest(132), atmLpTest(133), discovery(46), deltTraining(139), delt(140)ro SheAdslLineOpStateType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.9 |
sheAdslAtucPhysActualStdThis object provides actual ATU-C configuration based on outcome of negotiation with ATU-R. In this case, the parameter provides actual standard used for the connection.ro SheAdslLineConfStandardType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.10 |
sheAdslAtucPhysBertErrorThis object indicates the No. of bit errors detected during BERT.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.11 |
sheAdslAtucPhysTxAtmCellCounterThis object Provides transmit ATM cell counter.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.12 |
sheAdslAtucPhysRxAtmCellCounterThis object Provides receive ATM cell counter.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.13 |
sheAdslAtucPhysStartProgressThis object provides current detailed start up information to be used for debugging.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.14 |
sheAdslAtucPhysIdleBertErrorNumber of bit errors.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.15 |
sheAdslAtucPhysIdleBertCellsNumber of idle cells.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.16 |
sheAdslAtucPhysBertSyncIndicates if the Signal is in Sync or not.ro SheAdslAtucPhysBertSyncType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.17 |
sheAdslAtucPhysParametricTestResultIndicates the Result of the Parametric Test conducted on the Xcvr.ro SheAdslAtucPhysParametricTestResultType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.18 |
sheAdslAtucPwrMgmtStateLine Power Management State. (Not valid for ADSL G992.1)ro SheAdslPwrMgmtStateType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.19 |
sheAdslAtucPhysDeltHLINSCusDELT-related parameter that provides the scale factor to be applied to the upstream Hlin(f) values. Only available after a loop diagnostic procedure. (Not available for ADSL but ADSL2 & ADSL2plus).ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.20 |
sheAdslAtucPhysDeltHLINpsusDELT-related parameter that provides an array of complex upstream Hlin(f) values in linear scale. Every two octects refer to one element in this array of octets. (Not available for ADSL but ADSL2 & ADSL2plus). This parameter is an array of complex upstream Hlin(f) values in linear scale. Each array entry represents the Hlin(f = i*HLINGus* delta(f)) value for a particular subcarrier group index i, ranging from 0 to MIN(NSCus - 1,511). The Hlin(f) is represented as ((scale/2(exp15))*((a(i) + j*b(i))/2(exp15))), with scale being coded as a 16-bit unsigned integer and, a(i) and b(i) coded as 16-bit 2s complement signed integers in the (-2(exp15) + 1) to (+2(exp15) - 1) range. A special value a(i) = b(i) = -2(exp15) indicates that no measurement could be done for this subcarrier group because it is out of the passband or that the attenuation is out of range to be represented. This parameter is only available after a loop diagnostic procedure.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.21 |
sheAdslAtucPhysDeltHLOGMTusDELT-related parameter that provides the number of symbols used to measure the upstream Hlog(f). (Not available for ADSL but ADSL2 & ADSL2plus).ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.22 |
sheAdslAtucPhysDeltHLOGpsusDELT-related parameter that provides an array of real upstream Hlog(f) values in dB. (Not available for ADSL but ADSL2 & ADSL2plus). This parameter is an array of real upstream Hlog(f) values in dB. Each array entry represents the real Hlog(f = i*HLOGGus* delta(f)) value for a particular subcarrier group sub-carrier index i, ranging from 0 to MIN(NSCus - 1,511). The real Hlog(f) value is represented as (6 - m(i)/10), with m(i) 10-bit unsigned integer in the 0 to 1022 range. A special value m = 1023 indicates that no measurement could be done for this subcarrier group because it is out of the passband or that the attenuation is out of range to be represented.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.23 |
sheAdslAtucPhysDeltQLNMTusDELT-related parameter that provides the number of symbols used to measure the upstream QLN(f) values. (Not available for ADSL but ADSL2 & ADSL2plus).ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.24 |
sheAdslAtucPhysDeltQLNpsusDELT-related parameter that provides an array of real upstream QLN(f) values in dBm/Hz. Every two octects refer to one element in this array of octets. (Not available for ADSL but ADSL2 & ADSL2plus) This parameter is an array of real upstream QLN(f) values in dBm/Hz. Each array entry represents the QLN(f = i*QLNGus* delta(f)) value for a particular subcarrier group index i, ranging from 0 to MIN(NSCus - 1,511). The QLN(f) is represented as (-23 - n(i)/2), with n(i) an 8-bit unsigned integer in the 0 to 254 range. A special value n(i) = 255 indicates that no measurement could be done for this subcarrier group because it is out of the passband or that the noise PSD is out of range to be represented.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.25 |
sheAdslAtucPhysActStateThis object indicates the result of the ATU's line activation. Values include no error etc.ro SheAdslLineActStateType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.26 |
sheAdslAtucPhysCurrentBinStatusThis parameter represent the current bin status of used subcarriers. Each octet map to the corresponding bin.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.27 |
sheAdslAtucPhysCurrentBinBitLoadingThis parameter represent the current used bit loading per bin in upstream direction. Each octet map to the corresponding bin.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.28 |
sheAdslAtucPhysDeltSNRMTusDELT-related parameter that provides the number of symbols used to measure the upstream SNR(f) values. (Not available for ADSL and ADSL2plus) It is represented as a 16-bit unsigned value. After a loop diagnostic procedure, this parameter shall contain the number of symbols used to generate the associate parameter. It should correspond to the value specified in the Recommendation (e.g., the number of symbols in 1 s time interval for G.992.3).ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.29 |
sheAdslAtucPhysDeltDMTBinSNRusDELT-related parameter that provides an array of real upstream SNR(f) values in dB (Not available for ADSL and ADSL2plus) It is coded in the same way as the related downstream parameter.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.30 |
sheAdslAtucPhysDeltLastTxStateDELT-related parameter that provides last successful transmitted initialization state by the ATU-C. (Not available for ADSL and ADSL2plus) Initialization states are defined in the individual ADSL Recommendations and are counted from 0 (if G.994.1 is used) or 1 (if G.994.1 is not used) up to Showtime. This parameter must be interpreted along with the ADSL Transmission System. This parameter is available only when, after a failed full initialization, the line diagnostics procedures are activated on the line. Line diagnostics procedures can be activated by the operator of the system (through the Line State Forced line configuration parameter) or autonomously by the ATU-C or ATU-R.ro SheAdslPhysAtucDeltLastTxStateType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.31 |
sheAdslAtucPhysDeltSATNusDELT-related parameter that provides the uptream signal attenuation (length = 4 bytes). (Not available for ADSL and ADSL2plus). This parameter is the measured difference in dB in the total power transmitted by the ATU-R and the total power received by the ATU-C over all subcarriers during showtime. The upstream line attenuation ranges from 0 to +127 dB with 0.1 dB steps. A special value indicates the line attenuation is out of range to be represented. NOTE: During showtime, only a subset of the subcarriers may be transmitted by the ATU-R, as compared to diagnostics mode and initialization. Therefore, the upstream Signal attenuation may be significantly lower than the upstream Line attenuation.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.10.1.32 |
sheAdslAtucChanTableThis table provides one row for each ATUC channel. SEQUENCE OF SheAdslAtucChanEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.11 |
sheAdslAtucChanEntryAn entry in the adslAtucChanTable. This table is only supported by NE releases smaller then R2.5 (NO dualLatency support)!! SheAdslAtucChanEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.11.1 |
sheAdslAtucChanInterleaveDelayInterleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is Fast(125), use noSuchObject.ro Gauge32 UNITS "milli-seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.11.1.1 |
sheAdslAtucChanCurrTxRateActual transmit rate on this channel.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.11.1.2 |
sheAdslAtucChanPrevTxRateThe rate at the time of the last adslAtucRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAtucThresh(*)RateDown or less than adslAtucThresh(*)RateUp will not cause a trap or cause this object to change. (*) == Fast or Interleave. See AdslLineAlarmConfProfileEntry.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.11.1.3 |
sheAdslAtucChanCrcBlockLengthIndicates the length of the channel data-block on which the CRC operates. Refer to Line Code Specific MIBs, [11] and [12] for more information.ro Gauge32 UNITS "byte" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.11.1.4 |
sheAdslAtucChanCurrAtmStatusindicates an ncd or lcd failure if the counter surpasses 127. If neither ATM counter surpasses 127, the return value will be 'NoAtmDefect'. noAtmDefect(0), noCellDeleniation(1), lossOfCellDeleniation(2)ro SheAdslLineAtmStatus .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.11.1.5 |
sheAdslAtucChanRsSymbolsIndicates number of DMT symbols per Reed-Solomon code word (S) in the downstream direction. Note that S is not restricted to interleaved mode only. Even in fast mode, S is a valid constant value and is equal to 1.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.11.1.6 |
sheAdslAtucChanRsDepthIndicates interleaving depth (D) in the downstream direction. Note that D is not restricted to interleaved mode only. Even in fast mode, D is a valid constant value and is equal to 1.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.11.1.7 |
sheAdslAtucChanRsRedundancyIndicates number of redundant bytes (R) per Reed-Solomon code in the downstream direction.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.11.1.8 |
sheAdslAtucPerfDataTableThis table provides one row for each ATUC. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94). SEQUENCE OF SheAdslAtucPerfDataEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12 |
sheAdslAtucPerfDataEntryAn entry in adslAtucPerfDataTable. SheAdslAtucPerfDataEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1 |
sheAdslAtucPerfDataLofsCount of the number of Loss of Framing failures since agent reset.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.1 |
sheAdslAtucPerfDataLossCount of the number of Loss of Signal failures since agent reset.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.2 |
sheAdslAtucPerfDataLolsCount of the number of Loss of Link failures since agent reset.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.3 |
sheAdslAtucPerfDataLprsCount of the number of Loss of Power failures since agent reset.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.4 |
sheAdslAtucPerfDataESsCount of the number of Errored Seconds since agent reset. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.5 |
sheAdslAtucPerfDataInitsCount of the line initialization attempts since agent reset. Includes both successful and failed attempts.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.6 |
sheAdslAtucPerfDataStatFastRThe value of this object indicates the count of fast retrains.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.7 |
sheAdslAtucPerfDataStatFailedFastRThe value of this object indicates the count of failed fast retrains.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.8 |
sheAdslAtucPerfDataStatSesLThe value of this object indicates the count of severely errored second line.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.9 |
sheAdslAtucPerfDataStatUasLThe value of this object indicates the count of unavailable errored seconds.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.10 |
sheAdslAtucPerfDataValidIntervalsThe number of previous 15-minute intervals in the interval table for which data was collected. Given that <n> is the maximum # of intervals supported. The value will be <n> unless the measurement was (re-)started within the last (<n>*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.11 |
sheAdslAtucPerfDataInvalidIntervalsThe number of intervals in the range from 0 to the value of adslAtucPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.12 |
sheAdslAtucPerfDataCurr15MinTimeElapsedTotal elapsed seconds in this interval.ro AdslPerfTimeElapsed .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.13 |
sheAdslAtucPerfDataCurr15MinLofsCount of seconds in the current 15 minute interval when there was Loss of Framing.ro PerfCurrentCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.14 |
sheAdslAtucPerfDataCurr15MinLossCount of seconds in the current 15 minute interval when there was Loss of Signal.ro PerfCurrentCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.15 |
sheAdslAtucPerfDataCurr15MinLolsCount of seconds in the current 15 minute interval when there was Loss of Link.ro PerfCurrentCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.16 |
sheAdslAtucPerfDataCurr15MinLprsCount of seconds in the current 15 minute interval when there was Loss of Power.ro PerfCurrentCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.17 |
sheAdslAtucPerfDataCurr15MinESsCount of Errored Seconds in the current 15 minute interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.ro PerfCurrentCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.18 |
sheAdslAtucPerfDataCurr15MinInitsCount of the line initialization attempts in the current 15 minute interval. Includes both successful and failed attempts.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.19 |
sheAdslAtucPerfDataCurr15MinFastRCount of seconds in the current 15 minute interval when there was fast retrains. REFERENCE ITU G.997.1 Section 7.4.15.1ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.20 |
sheAdslAtucPerfDataCurr15MinFailedFastRCount of seconds in the current 15 minute interval when there was failed fast retrains. REFERENCE ITU G.997.1 Section 7.4.15.2ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.21 |
sheAdslAtucPerfDataCurr15MinSesLCount of seconds in the current 15 minute interval when there was severely errored seconds. REFERENCE ITU G.997.1 Section 7.2.1.1.7ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.22 |
sheAdslAtucPerfDataCurr15MinUasLCount of seconds in the current 15 minute interval when there was count for unavailable errored seconds. REFERENCE ITU G.997.1 Section 7.2.1.1.9ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.23 |
sheAdslAtucPerfDataCurr1DayTimeElapsedNumber of seconds that have elapsed since the beginning of the current 1-day interval.ro AdslPerfTimeElapsed .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.24 |
sheAdslAtucPerfDataCurr1DayLofsCount of the number of seconds when there was Loss of Framing during the current day as measured by adslAtucPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.25 |
sheAdslAtucPerfDataCurr1DayLossCount of the number of seconds when there was Loss of Signal during the current day as measured by adslAtucPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.26 |
sheAdslAtucPerfDataCurr1DayLolsCount of the number of seconds when there was Loss of Link during the current day as measured by adslAtucPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.27 |
sheAdslAtucPerfDataCurr1DayLprsCount of the number of seconds when there was Loss of Power during the current day as measured by adslAtucPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.28 |
sheAdslAtucPerfDataCurr1DayESsCount of Errored Seconds during the current day as measured by adslAtucPerfCurr1DayTimeElapsed. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.ro AdslPerfCurrDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.29 |
sheAdslAtucPerfDataCurr1DayInitsCount of the line initialization attempts in the day as measured by adslAtucPerfCurr1DayTimeElapsed. Includes both successful and failed attempts.ro AdslPerfCurrDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.30 |
sheAdslAtucPerfDataCurr1DayFastRCount of the number of seconds when there was fast retrains during the current day as measured by adslAtucPerfCurr1Day TimeElapsed. REFERENCE ITU G.997.1 Section 7.4.15.1ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.31 |
sheAdslAtucPerfDataCurr1DayFailedFastRCount of the number of seconds when there was failed fast retrains during the current day as measured by adslAtucPerfCurr1Day TimeElapsed.REFERENCE ITU G.997.1 Section 7.4.15.2ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.32 |
sheAdslAtucPerfDataCurr1DaySesLCount of the number of seconds when there was Severely Errored Seconds during the current day as measured by adslAtucPerfCurr1DayTimeElapsed. REFERENCE ITU G.997.1 Section 7.2.1.1.7ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.33 |
sheAdslAtucPerfDataCurr1DayUasLCount of the number of seconds when there was Unavailable Errored Seconds during the current day as measured by adslAtucPerfCurr1DayTimeElapsed. REFERENCE ITU G.997.1 Section 7.2.1.1.9ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.34 |
sheAdslAtucPerfDataPrev1DayTimeElapsedTotal elapsed seconds in this interval in seconds.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.35 |
sheAdslAtucPerfDataPrev1DayMoniSecsThe amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.36 |
sheAdslAtucPerfDataPrev1DayLofsCount of seconds in the interval when there was Loss of Framing within the most recent previous 1-day period.ro AdslPerfPrevDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.37 |
sheAdslAtucPerfDataPrev1DayLossCount of seconds in the interval when there was Loss of Signal within the most recent previous 1-day period.ro AdslPerfPrevDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.38 |
sheAdslAtucPerfDataPrev1DayLolsCount of seconds in the interval when there was Loss of Link within the most recent previous 1-day period.ro AdslPerfPrevDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.39 |
sheAdslAtucPerfDataPrev1DayLprsCount of seconds in the interval when there was Loss of Power within the most recent previous 1-day period.ro AdslPerfPrevDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.40 |
sheAdslAtucPerfDataPrev1DayESsCount of Errored Seconds within the most recent previous 1-day period. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.ro AdslPerfPrevDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.41 |
sheAdslAtucPerfDataPrev1DayInitsCount of the line initialization attempts in the most recent previous 1-day period. Includes both successful and failed attempts.ro AdslPerfPrevDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.42 |
sheAdslAtucPerfDataPrev1DayFastRCount of seconds in the interval when there was fast retrains within the most recent previous 1 day period. REFERENCE ITU G.997.1 Section 7.4.15.1ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.43 |
sheAdslAtucPerfDataPrev1DayFailedFastRCount of seconds in the interval when there was failed fast retrains within the most recent previous 1 day period. REFERENCE ITU G.997.1 Section 7.4.15.2ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.44 |
sheAdslAtucPerfDataPrev1DaySesLCount of seconds in the interval when there was severely errored seconds within the most recent previous 1 day period. REFERENCE ITU G.997.1 Section 7.2.1.1.7ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.45 |
sheAdslAtucPerfDataPrev1DayUasLCount of seconds in the interval when there was unavailable errored seconds within the most recent previous 1 day period. REFERENCE ITU G.997.1 Section 7.2.1.1.9ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.12.1.46 |
sheAdslAtucIntervalTableThis table provides one row for each ATUC performance data collection interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94). SEQUENCE OF SheAdslAtucIntervalEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.13 |
sheAdslAtucIntervalEntryAn entry in the adslAtucIntervalTable. SheAdslAtucIntervalEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.13.1 |
sheAdslAtucIntervalNumberPerformance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.13.1.1 |
sheAdslAtucIntervalValidDataThis variable indicates if the data for this interval is valid.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.13.1.2 |
sheAdslAtucIntervalEndTimeThis variable indicates the time of storing this interval.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.13.1.3 |
sheAdslAtucIntervalLofsCount of seconds in the interval when there was Loss of Framing.ro PerfIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.13.1.4 |
sheAdslAtucIntervalLossCount of seconds in the interval when there was Loss of Signal.ro PerfIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.13.1.5 |
sheAdslAtucIntervalLolsCount of seconds in the interval when there was Loss of Link.ro PerfIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.13.1.6 |
sheAdslAtucIntervalLprsCount of seconds in the interval when there was Loss of Power.ro PerfIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.13.1.7 |
sheAdslAtucIntervalESsCount of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.ro PerfIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.13.1.8 |
sheAdslAtucIntervalInitsCount of the line initialization attempts during the interval. Includes both successful and failed attempts.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.13.1.9 |
sheAdslAtucIntervalFastRThis variable indicates Count of seconds in the interval when there was Fast Retrains.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.13.1.10 |
sheAdslAtucIntervalFailedFastRThis variable indicates Count of seconds in the interval when there was Failed Fast Retrains.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.13.1.11 |
sheAdslAtucIntervalSesLThis variable indicates Count of seconds in the interval when there was severely errored seconds.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.13.1.12 |
sheAdslAtucIntervalUasLThis variable indicates Count of seconds in the interval when there was unavailable errored seconds.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.13.1.13 |
sheAdslAtucChanPerfDataTableThis table provides one row for each ATUC channel. SEQUENCE OF SheAdslAtucChanPerfDataEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14 |
sheAdslAtucChanPerfDataEntryAn entry in adslAtucChanPerfDataTable. This table is only supported by NE releases smaller then R2.5 (NO dualLatency support)!! SheAdslAtucChanPerfDataEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1 |
sheAdslAtucChanPerfDataTimeElapsedTotal elapsed seconds in this interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.1 |
sheAdslAtucChanPerfDataReceivedBlksCount of all encoded blocks received on this channel since agent reset.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.2 |
sheAdslAtucChanPerfDataTransmittedBlksCount of all encoded blocks transmitted on this channel since agent reset.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.3 |
sheAdslAtucChanPerfDataCorrectedBlksCount of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.4 |
sheAdslAtucChanPerfDataUncorrectBlksCount of all blocks received with uncorrectable errors since agent reset.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.5 |
sheAdslAtucChanPerfDataNcdCount of no cell delineation(ncd) on this channel.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.6 |
sheAdslAtucChanPerfDataOcdCount of out of cell delineation (ocd) on this channel.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.7 |
sheAdslAtucChanPerfDataHecHeader error check counter(hec) on this channel.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.8 |
sheAdslAtucChanPerfDataValidIntervalsThe number of previous 15-minute intervals in the interval table for which data was collected. Given that <n> is the maximum # of intervals supported. The value will be <n> unless the measurement was (re-)started within the last (<n>*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.9 |
sheAdslAtucChanPerfDataInvalidIntervalsThe number of intervals in the range from 0 to the value of adslAtucChanPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.10 |
sheAdslAtucChanPerfDataCurr15MinTimeElapsedTotal elapsed seconds in this interval.ro AdslPerfTimeElapsed .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.11 |
sheAdslAtucChanPerfDataCurr15MinReceivedBlksCount of all encoded blocks received on this channel within the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.12 |
sheAdslAtucChanPerfDataCurr15MinTransmittedBlksCount of all encoded blocks transmitted on this channel within the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.13 |
sheAdslAtucChanPerfDataCurr15MinCorrectedBlksCount of all blocks received with errors that were corrected on this channel within the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.14 |
sheAdslAtucChanPerfDataCurr15MinUncorrectBlksCount of all blocks received with uncorrectable errors on this channel within the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.15 |
sheAdslAtucChanPerfDataCurr15MinNcdCount of no cell delineation(ncd) on this channel within the current 15 minute time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.16 |
sheAdslAtucChanPerfDataCurr15MinOcdCount of out of cell delineation (ocd) on this channel within the current 15 minute time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.17 |
sheAdslAtucChanPerfDataCurr15MinHecHeader error check counter(hec) on this channel within the current 15 minute time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.18 |
sheAdslAtucChanPerfDataCurr1DayTimeElapsedNumber of seconds that have elapsed since the beginning of the current 1-day interval.ro AdslPerfTimeElapsed .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.19 |
sheAdslAtucChanPerfDataCurr1DayReceivedBlksCount of all encoded blocks received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.20 |
sheAdslAtucChanPerfDataCurr1DayTransmittedBlksCount of all encoded blocks transmitted on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.21 |
sheAdslAtucChanPerfDataCurr1DayCorrectedBlksCount of all blocks received with errors that were corrected on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.22 |
sheAdslAtucChanPerfDataCurr1DayUncorrectBlksCount of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.23 |
sheAdslAtucChanPerfDataCurr1DayNcdCount of no cell delineation (ncd) on this channel within the current 1 day time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.24 |
sheAdslAtucChanPerfDataCurr1DayOcdCount of out of cell delineation (ocd) on this channel within the current 1 day time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.25 |
sheAdslAtucChanPerfDataCurr1DayHecHeader error check counter (hec) on this channel within the current 1 day time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.26 |
sheAdslAtucChanPerfDataPrev1DayMoniSecsThe amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.27 |
sheAdslAtucChanPerfDataPrev1DayReceivedBlksCount of all encoded blocks received on this channel within the most recent previous 1-day period.ro AdslPerfPrevDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.28 |
sheAdslAtucChanPerfDataPrev1DayTransmittedBlksCount of all encoded blocks transmitted on this channel within the most recent previous 1-day period.ro AdslPerfPrevDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.29 |
sheAdslAtucChanPerfDataPrev1DayCorrectedBlksCount of all blocks received with errors that were corrected on this channel within the most recent previous 1-day period.ro AdslPerfPrevDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.30 |
sheAdslAtucChanPerfDataPrev1DayUncorrectBlksCount of all blocks received with uncorrectable errors on this channel within the most recent previous 1-day period.ro AdslPerfPrevDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.31 |
sheAdslAtucChanPerfDataPrev1DayNcdCount of no cell delineation (ncd) on this channel within the most recent previous 1-day period.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.32 |
sheAdslAtucChanPerfDataPrev1DayOcdCount of out of cell delineation (ocd) on this channel within the most recent previous 1-day period.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.33 |
sheAdslAtucChanPerfDataPrev1DayHecHeader error check counter(hec) on this channel within the most recent previous 1-day period.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.14.1.34 |
sheAdslAtucChanIntervalTableThis table provides one row for each ATUC channel's performance data collection interval. SEQUENCE OF SheAdslAtucChanIntervalEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.15 |
sheAdslAtucChanIntervalEntryAn entry in the adslAtucIntervalTable. This table is only supported by NE releases smaller then R2.5 (NO dualLatency support)!! SheAdslAtucChanIntervalEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.15.1 |
sheAdslAtucChanIntervalNumberPerformance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.15.1.1 |
sheAdslAtucChanIntervalValidDataThis variable indicates if the data for this interval is valid.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.15.1.2 |
sheAdslAtucChanIntervalEndTimeThis variable indicates the time of storing this interval.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.15.1.3 |
sheAdslAtucChanIntervalReceivedBlksCount of all encoded blocks received on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.15.1.4 |
sheAdslAtucChanIntervalTransmittedBlksCount of all encoded blocks transmitted on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.15.1.5 |
sheAdslAtucChanIntervalCorrectedBlksCount of all blocks received with errors that were corrected on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.15.1.6 |
sheAdslAtucChanIntervalUncorrectBlksCount of all blocks received with uncorrectable errors on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.15.1.7 |
sheAdslAtucChanIntervalNcdIndicates count of no cell delineation on this channel for this interval.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.15.1.8 |
sheAdslAtucChanIntervalOcdIndicates count of out cell delineation on this channel for this interval.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.15.1.9 |
sheAdslAtucChanIntervalHecIndicates Header error check counter on this channel during this interval.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.15.1.10 |
sheAdslAturPhysTableThis table provides one row for each ATUR Each row contains the Physical Layer Parameters table for that ATUR. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94). SEQUENCE OF SheAdslAturPhysEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16 |
sheAdslAturPhysEntryAn entry in the adslAturPhysTable. SheAdslAturPhysEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1 |
sheAdslAturPhysInvSerialNumberThe vendor specific string that identifies the vendor equipment.ro SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.1 |
sheAdslAturPhysInvVendorIDThe vendor ID code is a copy of the binary vendor identification field defined by the PHY[10] and expressed as readable characters.ro SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.2 |
sheAdslAturPhysInvVersionNumberThe vendor specific version number sent by this ATU as part of the initialization messages. It is a copy of the binary version number field defined by the PHY[10] and expressed as readable characters.ro SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.3 |
sheAdslAturPhysCurrSnrMgnNoise Margin as seen by this ATU with respect to its received signal in tenth dB.ro INTEGER (-640..640) UNITS "tenth dB" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.4 |
sheAdslAturPhysCurrAtnMeasured difference in the total power transmitted by the peer ATU and the total power received by this ATU.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.5 |
sheAdslAturPhysCurrStatusIndicates current state of the ATUR line. This is a bit-map of possible conditions. Due to the isolation of the ATUR when line problems occur, many state conditions like loss of power, loss of quality signal, and initialization errors, can not be determined. While trouble shooting ATUR, also use object, adslAtucCurrStatus. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUR failure due to not receiving valid frame 2 lossOfSignal ATUR failure due to not receiving signal 3 lossOfPower ATUR failure due to loss of power 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. This is intended to supplement ifOperStatus.ro SheAdslLineCurrentStatusType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.6 |
sheAdslAturPhysCurrOutputPwrMeasured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence.ro INTEGER (-310..310) UNITS "tenth dBm" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.7 |
sheAdslAturPhysCurrAttainableRateIndicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate.ro Gauge32 UNITS "kbps" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.8 |
sheAdslAturPhysConfigThis object provides the upstream and downstream ATU-R configuration data (EOC - read 5 sec after data mode).ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.9 |
sheAdslAturPhysDeltHLINSCdsDELT-related parameter that provides the scale factor to be applied to the downstream Hlin(f) values. (Not available for ADSL but ADSL2 & ADSL2plus).ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.10 |
sheAdslAturPhysDeltHLINpsdsDELT-related parameter that provides an array of complex downstream Hlin(f) values in linear scale. Every two octects refer to one element in this array of octets. (Not available for ADSL but ADSL2 & ADSL2plus). This parameter is an array of complex downstream Hlin(f) values in linear scale. Each array entry represents the Hlin(f = i*HLINGds* delta(f)) value for a particular subcarrier group index i, ranging from 0 to MIN(NSCds - 1,511). The Hlin(f) is represented as ((scale/2(exp15))*((a(i) + j*b(i))/2(exp15))), with scale being coded as a 16-bit unsigned integer and, a(i) and b(i) coded as 16-bit 2s complement signed integers in the (-2(exp15) + 1) to (+2(exp15) - 1) range. A special value a(i) = b(i) = -2(exp15) indicates that no measurement could be done for this subcarrier group because it is out of the passband or that the attenuation is out of range to be represented. This parameter is only available after a loop diagnostic procedure.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.11 |
sheAdslAturPhysDeltHLOGMTdsDELT-related parameter that provides the number of symbols used to measure the downstream Hlog(f). (Not available for ADSL but ADSL2 & ADSL2plus).ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.12 |
sheAdslAturPhysDeltHLOGpsdsDELT-related parameter that provides an array of real downstream Hlog(f) values in dB. (Not available for ADSL but ADSL2 & ADSL2plus). This parameter is an array of real downstream Hlog(f) values in dB. Each array entry represents the real Hlog(f = i*HLOGGds* delta(f)) value for a particular subcarrier group sub-carrier index i, ranging from 0 to MIN(NSCds - 1,511). The real Hlog(f) value is represented as (6 - m(i)/10), with m(i) 10-bit unsigned integer in the 0 to 1022 range. A special value m = 1023 indicates that no measurement could be done for this subcarrier group because it is out of the passband or that the attenuation is out of range to be represented.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.13 |
sheAdslAturPhysDeltQLNMTdsDELT-related parameter that provides the number of symbols used to measure the downstream QLN(f) values. (Not available for ADSL but ADSL2 & ADSL2plus).ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.14 |
sheAdslAturPhysDeltQLNpsdsDELT-related parameter that provides an array of real downstream QLN(f) values in dBm/Hz. Every two octects refer to one element in this array of octets. (Not available for ADSL but ADSL2 & ADSL2plus). This parameter is an array of real downstream QLN(f) values in dBm/Hz. Each array entry represents the QLN(f = i*QLNGds* delta(f)) value for a particular subcarrier group index i, ranging from 0 to MIN(NSCds - 1,511). The QLN(f) is represented as (-23 - n(i)/2), with n(i) an 8-bit unsigned integer in the 0 to 254 range. A special value n(i) = 255 indicates that no measurement could be done for this subcarrier group because it is out of the passband or that the noise PSD is out of range to be represented.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.15 |
sheAdslAturPhysCurrentBinBitLoadingThis parameter represent the current used bit loading per bin in downstream direction. Each octet map to the corresponding bin.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.16 |
sheAdslAturPhysDeltSNRMTdsDELT-related parameter that provides the number of symbols used to measure the downstream SNR(f) values. (Not available for ADSL and ADSL2plus) It is represented as a 16-bit unsigned value. After a loop diagnostic procedure, this parameter shall contain the number of symbols used to generate the associate parameter. It should correspond to the value specified in the Recommendation (e.g., the number of symbols in 1 s time interval for G.992.3).ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.17 |
sheAdslAturPhysDeltDMTBinSNRdsDELT-related parameter that provides an array of real downstream SNR(f) values in dB (Not available for ADSL and ADSL2plus) Each array entry represents the SNR(f = i*f) value for a particular subcarrier index i, ranging from 0 to NSCds C 1. The SNR(f) is represented as (C32 + snr(i)/2), with snr(i) an 8-bit unsigned integer in the 0 to 254 range. A special value snr(i) = 255 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the noise PSD is out of range to be represented.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.18 |
sheAdslAturPhysDeltLastTxStateDELT-related parameter that provides last successful transmitted initialization state by the ATU-R. (Not available for ADSL and ADSL2plus) Initialization states are defined in the individual ADSL Recommendations and are counted from 0 (if G.994.1 is used) or 1 (if G.994.1 is not used) up to Showtime. This parameter must be interpreted along with the ADSL Transmission System. This parameter is available only when, after a failed full initialization, the line diagnostics procedures are activated on the line. Line diagnostics procedures can be activated by the operator of the system (through the Line State Forced line configuration parameter) or autonomously by the ATU-C or ATU-R.ro SheAdslPhysAturDeltLastTxStateType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.19 |
sheAdslAturPhysDeltSATNdsDELT-related parameter that provides the downtream signal attenuation (length = 4 bytes). (Not available for ADSL and ADSL2plus). This parameter is the measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all subcarriers during showtime. The downstream line attenuation ranges from 0 to +127 dB with 0.1 dB steps. A special value indicates the line attenuation is out of range to be represented. NOTE: During showtime, only a subset of the subcarriers may be transmitted by the ATU-C, as compared to diagnostics mode and initialization. Therefore, the downstream Signal attenuation may be significantly lower than the downstream Line attenuation.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.16.1.20 |
sheAdslAturChanTableThis table provides one row for each ATUR channel. SEQUENCE OF SheAdslAturChanEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.17 |
sheAdslAturChanEntryAn entry in the adslAturChanTable. This table is only supported by NE releases smaller then R2.5 (NO dualLatency support)!! SheAdslAturChanEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.17.1 |
sheAdslAturChanInterleaveDelayInterleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is Fast(125), use noSuchObject.ro Gauge32 UNITS "milli-seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.17.1.1 |
sheAdslAturChanCurrTxRateActual transmit rate on this channel.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.17.1.2 |
sheAdslAturChanPrevTxRateThe rate at the time of the last adslAturRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAturThresh(*)RateDown or less than adslAturThresh(*)RateUp will not cause a trap or cause this object to change. (*) == Fast or Interleave. See AdslLineAlarmConfProfileEntry.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.17.1.3 |
sheAdslAturChanCrcBlockLengthIndicates the length of the channel data-block on which the CRC operates. Refer to Line Code Specific MIBs, [11] and [12] for more information.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.17.1.4 |
sheAdslAturChanCurrAtmStatusThis object indicates an ncd or lcd failure if the counter surpasses 127. If neither ATM counter surpasses 127, the return value will be NoAtmDefect. noAtmDefect(0), noCellDeleniation(1), lossOfCellDeleniation(2)ro SheAdslLineAtmStatus .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.17.1.5 |
sheAdslAturChanRsSymbolsThis object indicates number of DMT symbols per Reed- Solomon code word (S) in the upstream direction Note that S is not restricted to interleaved mode only. Even in fast mode, S is a valid constant value and is equal to 1.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.17.1.6 |
sheAdslAturChanRsDepthThis object indicates interleaving depth (D) in the upstream direction Note that D is not restricted to interleaved mode only. Even in fast mode, D is a valid constant value and is equal to 1.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.17.1.7 |
sheAdslAturChanRsRedundancyThis object indicates number of redundant bytes (R) per Reed-Solomon code in the upstream direction.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.17.1.8 |
sheAdslAturPerfDataTableThis table provides one row for each ATUR. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94). SEQUENCE OF SheAdslAturPerfDataEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18 |
sheAdslAturPerfDataEntryAn entry in adslAturPerfDataTable. SheAdslAturPerfDataEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1 |
sheAdslAturPerfDataLofsCount of the number of Loss of Framing failures since agent reset.ro Counter32 UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.1 |
sheAdslAturPerfDataLossCount of the number of Loss of Signal failures since agent reset.ro Counter32 UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.2 |
sheAdslAturPerfDataLprsCount of the number of Loss of Power failures since agent reset.ro Counter32 UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.3 |
sheAdslAturPerfDataESsCount of the number of Errored Seconds since agent reset. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.ro Counter32 UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.4 |
sheAdslAturPerfDataStatSesLThe value of this object reports the count of severely errored second-line since the last agent reset.ro Counter32 UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.5 |
sheAdslAturPerfDataStatUasLThe value of this object reports the count of unavailable seconds-line since the last agent reset.ro Counter32 UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.6 |
sheAdslAturPerfDataValidIntervalsThe number of previous 15-minute intervals in the interval table for which data was collected. Given that <n> is the maximum # of intervals supported. The value will be <n> unless the measurement was (re-)started within the last (<n>*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.7 |
sheAdslAturPerfDataInvalidIntervalsThe number of intervals in the range from 0 to the value of adslAturPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.8 |
sheAdslAturPerfDataCurr15MinTimeElapsedTotal elapsed seconds in this interval.ro AdslPerfTimeElapsed .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.9 |
sheAdslAturPerfDataCurr15MinLofsCount of seconds in the current 15 minute interval when there was Loss of Framing.ro PerfCurrentCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.10 |
sheAdslAturPerfDataCurr15MinLossCount of seconds in the current 15 minute interval when there was Loss of Signal.ro PerfCurrentCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.11 |
sheAdslAturPerfDataCurr15MinLprsCount of seconds in the current 15 minute interval when there was Loss of Power.ro PerfCurrentCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.12 |
sheAdslAturPerfDataCurr15MinESsCount of Errored Seconds in the current 15 minute interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.ro PerfCurrentCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.13 |
sheAdslAturPerfDataCurr15MinSesLFor the current 15-minute interval, adslAturPerfCurr15MinSesL reports the current number of seconds during which there have been severely errored seconds-line.ro PerfCurrentCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.14 |
sheAdslAturPerfDataCurr15MinUasLFor the current 15-minute interval, adslAturPerfCurr15MinUasL reports the current number of seconds during which there have been available seconds-line.ro PerfCurrentCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.15 |
sheAdslAturPerfDataCurr1DayTimeElapsedNumber of seconds that have elapsed since the beginning of the current 1-day interval.ro AdslPerfTimeElapsed .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.16 |
sheAdslAturPerfDataCurr1DayLofsCount of the number of seconds when there was Loss of Framing during the current day as measured by adslAturPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.17 |
sheAdslAturPerfDataCurr1DayLossCount of the number of seconds when there was Loss of Signal during the current day as measured by adslAturPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.18 |
sheAdslAturPerfDataCurr1DayLprsCount of the number of seconds when there was Loss of Power during the current day as measured by adslAturPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.19 |
sheAdslAturPerfDataCurr1DayESsCount of Errored Seconds during the current day as measured by adslAturPerfCurr1DayTimeElapsed. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.ro AdslPerfCurrDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.20 |
sheAdslAturPerfDataCurr1DaySesLFor the current day as measured by adslAturPerfCurr1DayTimeElapsed [RFC2662], adslAturPerfCurr1DaySesL reports the number of seconds during which there have been severely errored seconds-line.ro AdslPerfCurrDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.21 |
sheAdslAturPerfDataCurr1DayUasLFor the current day as measured by adslAturPerfCurr1DayTimeElapsed [RFC2662], adslAturPerfCurr1DayUasL reports the number of seconds during which there have been unavailable seconds-line.ro AdslPerfCurrDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.22 |
sheAdslAturPerfDataPrev1DayMoniSecsThe amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.23 |
sheAdslAturPerfDataPrev1DayLofsCount of seconds in the interval when there was Loss of Framing within the most recent previous 1-day period.ro AdslPerfPrevDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.24 |
sheAdslAturPerfDataPrev1DayLossCount of seconds in the interval when there was Loss of Signal within the most recent previous 1-day period.ro AdslPerfPrevDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.25 |
sheAdslAturPerfDataPrev1DayLprsCount of seconds in the interval when there was Loss of Power within the most recent previous 1-day period.ro AdslPerfPrevDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.26 |
sheAdslAturPerfDataPrev1DayESsCount of Errored Seconds within the most recent previous 1-day period. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.ro AdslPerfPrevDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.27 |
sheAdslAturPerfDataPrev1DaySesLFor the previous day, adslAturPerfPrev1DaySesL reports the number of seconds during which there were severely errored seconds-line.ro AdslPerfPrevDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.28 |
sheAdslAturPerfDataPrev1DayUasLFor the previous day, adslAturPerfPrev1DayUasL reports the number of seconds during which there were severely errored seconds-line.ro AdslPerfPrevDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.18.1.29 |
sheAdslAturIntervalTableThis table provides one row for each ATUR performance data collection interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94). SEQUENCE OF SheAdslAturIntervalEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.19 |
sheAdslAturIntervalEntryAn entry in the adslAturIntervalTable. SheAdslAturIntervalEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.19.1 |
sheAdslAturIntervalNumberPerformance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.19.1.1 |
sheAdslAturIntervalValidDataThis variable indicates if the data for this interval is valid.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.19.1.2 |
sheAdslAturIntervalEndTimeThis variable indicates the time of storing this interval.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.19.1.3 |
sheAdslAturIntervalLofsCount of seconds in the interval when there was Loss of Framing.ro PerfIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.19.1.4 |
sheAdslAturIntervalLossCount of seconds in the interval when there was Loss of Signal.ro PerfIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.19.1.5 |
sheAdslAturIntervalLprsCount of seconds in the interval when there was Loss of Power.ro PerfIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.19.1.6 |
sheAdslAturIntervalESsCount of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.ro PerfIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.19.1.7 |
sheAdslAturIntervalSesLFor the each interval, adslAturIntervalSesL reports the number of seconds during which there have been severely errored seconds-line.ro PerfIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.19.1.8 |
sheAdslAturIntervalUasLFor the each interval, adslAturIntervalUasL reports the number of seconds during which there have been unavailable seconds-line.ro PerfIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.19.1.9 |
sheAdslAturChanPerfDataTableThis table provides one row for each ATUR channel. SEQUENCE OF SheAdslAturChanPerfDataEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20 |
sheAdslAturChanPerfDataEntryAn entry in adslAturChanPerfDataTable. This table is only supported by NE releases smaller then R2.5 (NO dualLatency support)!! SheAdslAturChanPerfDataEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1 |
sheAdslAturChanPerfDataReceivedBlksCount of all encoded blocks received on this channel since agent reset.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.1 |
sheAdslAturChanPerfDataTransmittedBlksCount of all encoded blocks transmitted on this channel since agent reset.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.2 |
sheAdslAturChanPerfDataCorrectedBlksCount of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.3 |
sheAdslAturChanPerfDataUncorrectBlksCount of all blocks received with uncorrectable errors since agent reset.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.4 |
sheAdslAturChanPerfDataExtnNcdNumber of packets with no cell delineation(NCD) error on this channel.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.5 |
sheAdslAturChanPerfDataExtnHecNumber of packets with Header error check (HEC) error on this channel.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.6 |
sheAdslAturChanPerfDataPerfValidIntervalsThe number of previous 15-minute intervals in the interval table for which data was collected. Given that <n> is the maximum # of intervals supported. The value will be <n> unless the measurement was (re-)started within the last (<n>*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.7 |
sheAdslAturChanPerfDataPerfInvalidIntervalsThe number of intervals in the range from 0 to the value of adslAturChanPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.8 |
sheAdslAturChanPerfDataCurr15MinTimeElapsedTotal elapsed seconds in this interval. A full interval is 900 seconds.ro AdslPerfTimeElapsed .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.9 |
sheAdslAturChanPerfDataCurr15MinReceivedBlksCount of all encoded blocks received on this channel within the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.10 |
sheAdslAturChanPerfDataCurr15MinTransmittedBlksCount of all encoded blocks transmitted on this channel within the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.11 |
sheAdslAturChanPerfDataCurr15MinCorrectedBlksCount of all blocks received with errors that were corrected on this channel within the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.12 |
sheAdslAturChanPerfDataCurr15MinUncorrectBlksCount of all blocks received with uncorrectable errors on this channel within the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.13 |
sheAdslAturChanPerfDataExtnCurr15MinNcdNumber of packets with no cell delineation(NCD) error on this channel within the current 15 minute time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.14 |
sheAdslAturChanPerfDataExtnCurr15MinHecNumber of packets with Header error check (HEC) error on this channel within the current 15 minute time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.15 |
sheAdslAturChanPerfDataCurr1DayTimeElapsedNumber of seconds that have elapsed since the beginning of the current 1-day interval.ro AdslPerfTimeElapsed .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.16 |
sheAdslAturChanPerfDataCurr1DayReceivedBlksCount of all encoded blocks received on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.17 |
sheAdslAturChanPerfDataCurr1DayTransmittedBlksCount of all encoded blocks transmitted on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.18 |
sheAdslAturChanPerfDataCurr1DayCorrectedBlksCount of all blocks received with errors that were corrected on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.19 |
sheAdslAturChanPerfDataCurr1DayUncorrectBlksCount of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.20 |
sheAdslAturChanPerfDataExtnCurr1DayNcdNumber of packets with no cell delineation (NCD) error on this channel within the current 1 day time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.21 |
sheAdslAturChanPerfDataExtnCurr1DayHecNumber of packets with Header error check (HEC) error on this channel within the current 1 day time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.22 |
sheAdslAturChanPerfDataPrev1DayMoniSecsThe amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.23 |
sheAdslAturChanPerfDataPrev1DayReceivedBlksCount of all encoded blocks received on this channel within the most recent previous 1-day period.ro AdslPerfPrevDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.24 |
sheAdslAturChanPerfDataPrev1DayTransmittedBlksCount of all encoded blocks transmitted on this channel within the most recent previous 1-day period.ro AdslPerfPrevDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.25 |
sheAdslAturChanPerfDataPrev1DayCorrectedBlksCount of all blocks received with errors that were corrected on this channel within the most recent previous 1-day period.ro AdslPerfPrevDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.26 |
sheAdslAturChanPerfDataPrev1DayUncorrectBlksCount of all blocks received with uncorrectable errors on this channel within the most recent previous 1-day period.ro AdslPerfPrevDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.27 |
sheAdslAturChanPerfDataExtnPrev1DayNcdNumber of packets with no cell delineation (NCD) error on this channel within the most recent previous period.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.28 |
sheAdslAturChanPerfDataExtnPrev1DayHecNumber of packets with Header error check (HEC) error on this channel within the most recent previous period.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.20.1.29 |
sheAdslAturChanIntervalTableThis table provides one row for each ATUR channel's performance data collection interval. SEQUENCE OF SheAdslAturChanIntervalEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.21 |
sheAdslAturChanIntervalEntryAn entry in the adslAturIntervalTable. This table is only supported by NE releases smaller then R2.5 (NO dualLatency support)!! SheAdslAturChanIntervalEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.21.1 |
sheAdslAturChanIntervalNumberPerformance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.21.1.1 |
sheAdslAturChanIntervalValidDataThis variable indicates if the data for this interval is valid.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.21.1.2 |
sheAdslAturChanIntervalEndTimeThis variable indicates the time of storing this interval.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.21.1.3 |
sheAdslAturChanIntervalReceivedBlksCount of all encoded blocks received on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.21.1.4 |
sheAdslAturChanIntervalTransmittedBlksCount of all encoded blocks transmitted on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.21.1.5 |
sheAdslAturChanIntervalCorrectedBlksCount of all blocks received with errors that were corrected on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.21.1.6 |
sheAdslAturChanIntervalUncorrectBlksCount of all blocks received with uncorrectable errors on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.21.1.7 |
sheAdslAturChanIntervalNcdIndicates count of no cell delineation on this channel for this interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.21.1.8 |
sheAdslAturChanIntervalHecIndicates Header error check counter on this channel during this interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.21.1.9 |
sheAdslLineAlarmConfProfileTableThis table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the modem for a physical line SEQUENCE OF SheAdslLineAlarmConfProfileEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22 |
sheAdslLineAlarmConfProfileEntryEach entry consists of a list of parameters that represents the configuration of an ADSL modem. 'Dynamic' profiles are implemented. A default profile will always exist. This profile's name will be set to `DEFVAL' and its parameters will be set to vendor specific values, unless otherwise specified in this document. SheAdslLineAlarmConfProfileEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1 |
sheAdslLineAlarmConfProfileIndexTableindex.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.1 |
sheAdslLineAlarmConfProfileNameThis object is used by the line alarm configuration table in order to identify a row of this table. Dynamic profiles are implemented. The profile name is user specified. The system will always provide a default profile whose name is `DEFVAL'. This characters are not allowed: space : ? leading numbersro SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.2 |
sheAdslLineAlarmConfProfileOpStateTrapEnableEnables and disables the OpStateChangeTrap.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.3 |
sheAdslLineAlarmConfProfileAtucThreshFastRateUpApplies to `Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.4 |
sheAdslLineAlarmConfProfileAtucThreshInterleaveRateUpApplies to `Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.5 |
sheAdslLineAlarmConfProfileAtucThreshFastRateDownApplies to `Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.6 |
sheAdslLineAlarmConfProfileAtucThreshInterleaveRateDownApplies to `Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when:ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.7 |
sheAdslLineAlarmConfProfileAtucInitFailureTrapEnableEnables and disables the InitFailureTrap. This object is defaulted disable(2).ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.8 |
sheAdslLineAlarmConfProfileAtucThresh15MinLofsThe number of Loss of Frame Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLofsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.9 |
sheAdslLineAlarmConfProfileAtucThresh15MinLossThe number of Loss of Signal Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLossThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.10 |
sheAdslLineAlarmConfProfileAtucThresh15MinLolsThe number of Loss of Link Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLolsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.11 |
sheAdslLineAlarmConfProfileAtucThresh15MinLprsThe number of Loss of Power Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLprsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.12 |
sheAdslLineAlarmConfProfileAtucThresh15MinESsThe number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfESsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.13 |
sheAdslLineAlarmConfProfileAtucThresh15MinSesLThe number of Severe errored seconds encountered by an ADSL interface within any giving 15 minutes performance data collection period, which cause the SNMP agend to send an adslAtucPerfSesLTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.14 |
sheAdslLineAlarmConfProfileAtucThresh15MinUasLThe number of Unavailable seconds encountered by an ADSL interface within any giving 15 minutes performance data collection period, which cause the SNMP agend to send an adslAtucPerfUasLTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.15 |
sheAdslLineAlarmConfProfileAtucThresh15MinFailFastRThe number of failed retrains encountered by an ADSL interface within any giving 15 minutes performance data collection period, which cause the SNMP agent to send an adslAtucFailedFastRTrap. Not supported yet!ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.16 |
sheAdslLineAlarmConfProfileAturThreshFastRateUpApplies to `Fast' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.17 |
sheAdslLineAlarmConfProfileAturThreshInterleaveRateUpApplies to `Interleave' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.18 |
sheAdslLineAlarmConfProfileAturThreshFastRateDownApplies to `Fast' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.19 |
sheAdslLineAlarmConfProfileAturThreshInterleaveRateDownApplies to `Interleave' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.20 |
sheAdslLineAlarmConfProfileAturThresh15MinLofsThe number of Loss of Frame Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLofsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.21 |
sheAdslLineAlarmConfProfileAturThresh15MinLossThe number of Loss of Signal Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLossThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.22 |
sheAdslLineAlarmConfProfileAturThresh15MinLprsThe number of Loss of Power Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLprsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.23 |
sheAdslLineAlarmConfProfileAturThresh15MinESsThe number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfESsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.24 |
sheAdslLineAlarmConfProfileAturThresh15MinSesLThe number of Severe errored seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfSesLThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.25 |
sheAdslLineAlarmConfProfileAturThresh15MinUasLThe number of Unavailable seconds encountered by an ADSL interface within any giving 15 minutes performance data collection period, which cause the SNMP agend to send an adslAturPerfUasLTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.22.1.26 |
sheAdslLineAlarmConfProfileControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23 |
sheAdslLineAlarmConfProfileControlRequestcreateAdslLineAlarmConfProfile: sheAdslLineAlarmConfProfileControlName ... modifyAdslLineAlarmConfProfile: sheAdslLineAlarmConfProfileControlIndex sheAdslLineAlarmConfProfileControlName ... deleteAdslLineAlarmConfProfile: sheAdslLineAlarmConfProfileControlIndex sheAdslLineAlarmConfProfileControlNamerw SheAdslControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.1 |
sheAdslLineAlarmConfProfileControlIndexIndex of the table entry to be configured. Needed for modify or delete.rw Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.2 |
sheAdslLineAlarmConfProfileControlStatusThe status of a user command.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.3 |
sheAdslLineAlarmConfProfileControlTimerThe maximum wait time for the manager for a long running user command.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.4 |
sheAdslLineAlarmConfProfileControlReqResultThe result of the last user command.ro SheAdslControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.5 |
sheAdslLineAlarmConfProfileControlTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.6 |
sheAdslLineAlarmConfProfileControlNameDescriptional name.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.7 |
sheAdslLineAlarmConfProfileControlOpStateTrapEnableEnables and disables the LineStateTrap.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.8 |
sheAdslLineAlarmConfProfileControlAtucThreshFastRateUpApplies to `Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.9 |
sheAdslLineAlarmConfProfileControlAtucThreshInterleaveRateUpApplies to `Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.10 |
sheAdslLineAlarmConfProfileControlAtucThreshFastRateDownApplies to `Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.11 |
sheAdslLineAlarmConfProfileControlAtucThreshInterleaveRateDownApplies to `Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.12 |
sheAdslLineAlarmConfProfileControlAtucInitFailureTrapEnableEnables and disables the InitFailureTrap. This object is defaulted disable(2).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.13 |
sheAdslLineAlarmConfProfileControlAtucThresh15MinLofsThe number of Loss of Frame Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLofsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.14 |
sheAdslLineAlarmConfProfileControlAtucThresh15MinLossThe number of Loss of Signal Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLossThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.15 |
sheAdslLineAlarmConfProfileControlAtucThresh15MinLolsThe number of Loss of Link Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLolsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.16 |
sheAdslLineAlarmConfProfileControlAtucThresh15MinLprsThe number of Loss of Power Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLprsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.17 |
sheAdslLineAlarmConfProfileControlAtucThresh15MinESsThe number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfESsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.18 |
sheAdslLineAlarmConfProfileControlAtucThresh15MinSesLThe number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfSesLThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.19 |
sheAdslLineAlarmConfProfileControlAtucThresh15MinUasLThe number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfUasLThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.20 |
sheAdslLineAlarmConfProfileControlAtucThresh15MinFailFastRThe number of failed retrains encountered by an ADSL interface within any giving 15 minutes performance data collection period, which cause the SNMP agent to send an adslAtucFailedFastRTrap.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.21 |
sheAdslLineAlarmConfProfileControlAturThreshFastRateUpApplies to `Fast' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.22 |
sheAdslLineAlarmConfProfileControlAturThreshInterleaveRateUpApplies to `Interleave' channels only. configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.23 |
sheAdslLineAlarmConfProfileControlAturThreshFastRateDownApplies to `Fast' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.24 |
sheAdslLineAlarmConfProfileControlAturThreshInterleaveRateDownApplies to `Interleave' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.25 |
sheAdslLineAlarmConfProfileControlAturThresh15MinLofsThe number of Loss of Frame Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLofsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.26 |
sheAdslLineAlarmConfProfileControlAturThresh15MinLossThe number of Loss of Signal Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLossThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.27 |
sheAdslLineAlarmConfProfileControlAturThresh15MinLprsThe number of Loss of Power Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLprsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.28 |
sheAdslLineAlarmConfProfileControlAturThresh15MinESsThe number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfESsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.29 |
sheAdslLineAlarmConfProfileControlAturThresh15MinSesLThe number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfSesLThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.30 |
sheAdslLineAlarmConfProfileControlAturThresh15MinUasLThe number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfUasLThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.23.31 |
sheAdslNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24 |
sheAdslAtucTraps OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1 |
sheAdslAtucPerfLofsThreshTrapLoss of Framing 15-minute interval threshold reached. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1.1 |
sheAdslAtucPerfLossThreshTrapLoss of Signal 15-minute interval threshold reached. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1.2 |
sheAdslAtucPerfLolsThreshTrapLoss of Link 15-minute interval threshold reached. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1.3 |
sheAdslAtucPerfLprsThreshTrapLoss of Power 15-minute interval threshold reached. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1.4 |
sheAdslAtucPerfESsThreshTrapErrored Second 15-minute interval threshold reached. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1.5 |
sheAdslAtucRateChangeTrapThe ATUCs transmit rate has changed (RADSL mode only) NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1.6 |
sheAdslAtucStatusTrapATUC initialization failed. See sheAdslAtucPhysCurrStatus for potential reasons. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1.7 |
sheAdslAtucFailedFastRThreshTrapFailed Fast Retrains 15-minute threshold reached. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1.8 |
sheAdslAtucPerfSesLThreshTrapSeverely errored seconds-line 15-minute threshold reached. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1.9 |
sheAdslAtucPerfUasLThreshTrapUnavailable seconds-line 15-minute threshold reached. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1.10 |
sheAdslLineStateTrapThe operational line state was changed. This trap will be enabled/disabled over the value of sheLineAlarmConfProfileOpStateTrapEnable. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1.11 |
sheAdslAtucPerfLolThis alarm informs the link between the line card and modem is disconnected for unidentied reason, not dying gasp. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1.12 |
sheAdslAtucPerfLprThis alarm informs the link between the line card and modem is disconnected for dying gasp. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1.13 |
sheAdslAtucPerfLosAn LOS failure is declared after 2.5 +(-) 0.5 s of contiguous LOS defect, or, if LOS defect is present when the criteria for LOF failure declaration have been met (see LOF definition below). A LOS failure is cleared after 10 +(-) 0.5 s of no LOS defect. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1.14 |
sheAdslAtucPerfLofAn LOF failure is declared after 2.5 +(-) 0.5 s of contiguous SEF defect, except when an LOS defect or failure is present (see LOS definition above). A LOF failure is cleared when LOS failure is declared, or after 10 +(-) 0.5 s of no SEF defect. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1.15 |
sheAdslLineActStateTrapThe line activation command was sent to Line card system NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1.16 |
sheAdslInitFailTrapThe init fail trap, trap will only send if a initialication was detected. This trap could be enabled/disabled over the value of sheLineAlarmConfProfileInitFailTrapEnable. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.1.17 |
sheAdslAturTraps OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.2 |
sheAdslAturRateChangeTrapThe ATURs transmit rate has changed (RADSL mode only) NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.2.1 |
sheAdslAturPerfLofsThreshTrapLoss of Framing 15-minute interval threshold reached. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.2.2 |
sheAdslAturPerfLossThreshTrapLoss of Signal 15-minute interval threshold reached. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.2.3 |
sheAdslAturPerfLprsThreshTrapLoss of Power 15-minute interval threshold reached. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.2.4 |
sheAdslAturPerfESsThreshTrapErrored Second 15-minute interval threshold reached. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.2.5 |
sheAdslAturPerfSesLThreshTrapSeverely errored seconds-line 15-minute threshold reached. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.2.6 |
sheAdslAturPerfUasLThreshTrapUnavailable seconds-line 15-minute threshold reached. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.2.7 |
sheAdslAturStatusTrapATUC initialization failed. See sheAdslAtucPhysCurrStatus for potential reasons. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.2.8 |
sheAdslAturPerfLosAn LOS failure is declared after 2.5 +(-) 0.5 s of contiguous LOS defect, or, if LOS defect is present when the criteria for LOF failure declaration have been met (see LOF definition below). A LOS failure is cleared after 10 +(-) 0.5 s of no LOS defect.. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.2.9 |
sheAdslAturPerfLofAn LOF failure is declared after 2.5 +(-) 0.5 s of contiguous SEF defect, except when an LOS defect or failure is present (see LOS definition above). A LOF failure is cleared when LOS failure is declared, or after 10 +(-) 0.5 s of no SEF defect. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.2.10 |
sheAdslConfigurationTraps OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3 |
sheAdslLineConfProfileCreatedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.2 |
sheAdslLineConfProfileModifiedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.3 |
sheAdslLineConfProfileDeletedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.4 |
sheAdslLineConfExtnProfileModifiedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.6 |
sheAdslLineAlarmConfProfileCreatedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.8 |
sheAdslLineAlarmConfProfileModifiedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.9 |
sheAdslLineAlarmConfProfileDeletedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.10 |
sheAdslLineConfigurationModifiedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.11 |
sheAdslLinePerfCounterClearedperformance counter cleared NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.12 |
sheAdslLineConfProfileReqResultConfiguration notification for long running command - Result-Trap. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.13 |
sheAdslLineConfExtnProfileReqResultConfiguration notification for long running command - Result-Trap. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.14 |
sheAdslLineAlarmConfProfileReqResultConfiguration notification for long running command - Result-Trap. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.15 |
sheAdslLineDpboProfileCreatedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.16 |
sheAdslLineDpboProfileModifiedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.17 |
sheAdslLineDpboProfileDeletedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.18 |
sheAdslLineDpboProfileReqResultConfiguration notification for long running command - Result-Trap. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.19 |
sheAdslLineDpboProfileSetReqResultConfiguration notification for long running command - Result-Trap. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.20 |
sheAdslLineDpboProfileSetModifiedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.21 |
sheAdslLineInpValueTruncatedInto2INP value was truncated into 2 because of the limitation of Conexant. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.3.22 |
sheAdslLineAlarmTraps OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.4 |
sheAdslLineAlarmLOSATUC failure due to not receiving signal NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.4.1 |
sheAdslLineAlarmLOFATUC failure due to not receiving valid frame. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.4.2 |
sheAdslLineAlarmLOLATUC failure due to inability to link with xTUR NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.4.3 |
sheAdslLineAlarmLPRATUR failure due to loss of power NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.4.4 |
sheAdslLineAlarmIMNRLoss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. Detected by Atuc-side. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.24.4.5 |
sheAdslVccTpTableThe VccTp-Table. SEQUENCE OF SheAdslVccTpEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25 |
sheAdslVccTpEntryThis table contains the VccTp-Configurations. There will be one entry for every adsl-interface available per default. This default entry should never be deleted. SheAdslVccTpEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1 |
sheAdslVccTpIndexIndex for that table. The index will follow this rule: VccTpIndex = (VccTpSubLayerIndex << 4) + VccTpNumberro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.1 |
sheAdslVccTpSubLayerIndexifIndex of the underlaying adsl-interface.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.2 |
sheAdslVccTpNumberThis is the logical number of VccTP on the corresponding interface. Maximum value is 8.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.3 |
sheAdslVccTpVpiThe VPI - Value.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.4 |
sheAdslVccTpVciThe Vci - Value.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.5 |
sheAdslVccTpOamLevelThe OAM level for loop test on VP/VC level. Valid: f5 (for VC).ro SheAdslOamLevelType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.6 |
sheAdslVccTpLoopTestThe type of loop test . For EndToEnd loop test loop location ID is FF..FF.ro SheAdslOamLoopTestType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.7 |
sheAdslVccTpLoopTestResultPossible values: segSuccess(0), segFailure(1), endToEndSuccess(2), endToEndFailure(3), aborted(4), progress(5), notAvailable(65535)ro SheAdslVccTpLoopTestResultType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.8 |
sheAdslVccTpLoopLocIdTest cell loopback location. It is an identifier known by the crafts person identifying a ATM node in the ATM network. For EndToEnd loop test the default value is valid.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.9 |
sheAdslVccTpAlarmSeverityIndexIndex to the AlarmSeverityProfileTable. Defines the actual AlarmSeverities for all alarms per VccTp.ro SheAlarmSevProfileIndex (SHE-ALARMING-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.10 |
sheAdslVccTpEgressQosClassEgress Qos Typero SheAdslAtmQosType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.11 |
sheAdslVccTpEgressPeakCellRateValid when sheAdslVccTpEgressQosClass is not unshapedro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.12 |
sheAdslVccTpEgressSustainedCellRateValid when sheAdslVccTpEgressQosClass is shapingRtVbr or shapingNrtVbrro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.13 |
sheAdslVccTpEgressMaxBurstSizeValid when sheAdslVccTpEgressQosClass is shapingRtVbr or shapingNrtVbrro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.14 |
sheAdslVccTpEgressWeightValid only when sheAdslVccTpEgressQosClass is unshaped.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.15 |
sheAdslVccTpIngressSustainedCellRateGFR scr for ingress policingro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.16 |
sheAdslVccTpIngressMaxBurstSizeGFR mbs for ingress policingro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.17 |
sheAdslVccTpAdminStateEnable/disable single VccTp. Default value is enabled.ro SheAdslEnableType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.18 |
sheAdslVccTpOrlThe output rate limiting value. This value is only valid for the default VccTp-entry's with VccTp-Number 1. All other will show a 0 and could not be modified.ro Unsigned32 (0 | 64..29952) UNITS "kbps" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.19 |
sheAdslVccTpUsedDslChannelThis attribute defines the usage of a dsl bearer channel by this VccTp. The availability of dsl channels depends on the configuration of the underlaying adsl line (VccTpSublayerIndex points to this line). Valid values for configuration: fastOnly(2) - only in dualLatency mode available interleavedOnly(3) - only in dualLatency mode available If singleLatency mode is used on the underlaying dslInterface, the port will select the available channel for all existing VccTP's automaticaly. Note: Depending on the used AdslLineProfile configuration, the following scenarios are possible: 1. default state: ->line uses interleaved channel only ->VccTp's uses always the available channel. ->A modification of sheAdslVccTpUsedDslChannel will be rejected! 2. modify line profile ->line uses fast channel only ->VccTp's uses always the available channel. ->CXU send notifications. ->A modification of sheAdslVccTpUsedDslChannel will be rejected! 3. modify line profile ->line uses dualLatency ->VccTp's uses the same channel as before. 4. modify VccTp entry ->line uses dualLatency ->the slected VccTp uses fast or interleaved channel only according to the configuration. ->A setting of value fastOrInterleaved(4) will be rejected. 5. modify line profile ->line goes back to use interleaved channel only ->VccTp's uses the interleaved channel ->notification will be send if a change is needed.ro SheAdslConfLineType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.20 |
sheAdslVccTpEncapsulationUsed encapsulation type over AAL5 for this VccTp.ro SheAdslAtmEncapType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.25.1.21 |
sheAdslVccTpControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26 |
sheAdslVccTpControlRequestcreateAdslVccTp: sheAdslVccTpControlSubLayerIndex sheAdslVccTpControlVpi sheAdslVccTpControlVci deleteAdslVccTp: sheAdslVccTpControlIndex modifyAdslVccTp: sheAdslVccTpControlIndex sheAdslVccTpControlVpi sheAdslVccTpControlVci sheAdslVccTpControlAlarmSeverityIndex modifyAdslVccTpLoopTest: sheAdslVccTpControlIndex sheAdslVccTpControlLoopTest modifyAdslVccTpEgressShaping: sheAdslVccTpControlIndex sheAdslVccTpControlEgressQosClass sheAdslVccTpControlEgressPeakCellRate sheAdslVccTpControlEgressSustainedCellRate sheAdslVccTpControlEgressMaxBurstSize sheAdslVccTpControlEgressWeight modifyAdslVccTpIngressPolicing: sheAdslVccTpControlIndex sheAdslVccTpControlIngressSustainedCellRate sheAdslVccTpControlIngressMaxBurstSize modifyAdslVccTpAdminState: sheAdslVccTpControlIndex sheAdslVccTpControlAdminState modifyAdslVccTpOrl: sheAdslVccTpControlIndex sheAdslVccTpControlOrl Only in dualLatency mode possible!! modifyAdslVccTpUsedDslChannel: sheAdslVccTpControlIndex sheAdslVccTpControlUsedDslChannel ## New for R2.6 deleteAdslVccTpPerformanceCounters: sheAdslVccTpControlIndex modifyAdslVccTpEncap: sheAdslVccTpControlIndex sheAdslVccTpControlEncapsulationrw SheAdslControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.1 |
sheAdslVccTpControlIndexIndex of the Table-entry to be configured.rw Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.2 |
sheAdslVccTpControlStatusThe status of a user command.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.3 |
sheAdslVccTpControlTimerThe maximum wait time for the manager for a long running user command.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.4 |
sheAdslVccTpControlReqResultThe result of the last user command.ro SheAdslControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.5 |
sheAdslVccTpControlTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.6 |
sheAdslVccTpControlSubLayerIndexDescription.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.7 |
sheAdslVccTpControlVpiVpirw Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.9 |
sheAdslVccTpControlVciVcirw Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.10 |
sheAdslVccTpControlLoopTestActual LoopTest-Value. Only None or endToEnd will be accepted.rw SheAdslOamLoopTestType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.11 |
sheAdslVccTpControlAlarmSeverityIndexIndex of the used AlarmSeverityProfile.rw SheAlarmSevProfileIndex (SHE-ALARMING-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.12 |
sheAdslVccTpControlEgressQosClassEgress QoS Type.rw SheAdslAtmQosType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.13 |
sheAdslVccTpControlEgressPeakCellRateValid when sheAdslVccTpEgressQosClass is not unshapedrw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.14 |
sheAdslVccTpControlEgressSustainedCellRateValid when sheAdslVccTpEgressQosClass is shapingRtVbr or shapingNrtVbrrw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.15 |
sheAdslVccTpControlEgressMaxBurstSizeValid when sheAdslVccTpEgressQosClass is shapingRtVbr or shapingNrtVbrrw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.16 |
sheAdslVccTpControlEgressWeightValid only when sheAdslVccTpEgressQosClass is unshaped.rw Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.17 |
sheAdslVccTpControlIngressSustainedCellRateGFR scr for ingress policingrw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.18 |
sheAdslVccTpControlIngressMaxBurstSizeGFR mbs for ingress policingrw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.19 |
sheAdslVccTpControlAdminStatelook at tablerw SheAdslEnableType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.20 |
sheAdslVccTpControlOrllook at tablerw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.21 |
sheAdslVccTpControlUsedDslChannelThis attribute defines the usage of a dsl bearer channel by this VccTp. The availability of dsl channels depends on the configuration of the underlaying adsl line (VccTpSublayerIndex points to this line). Valid values for configuration: fastOnly(2) - only in dualLatency mode available interleavedOnly(3) - only in dualLatency mode available In singleLatency mode , no configuration is possible.rw SheAdslConfLineType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.22 |
sheAdslVccTpControlEncapsulationEncapsulation type over AAL5.rw SheAdslAtmEncapType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.26.23 |
sheAdslVccTpNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.27 |
sheAdslVccTpCreatedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.27.1 |
sheAdslVccTpModifiedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.27.2 |
sheAdslVccTpDeletedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.27.3 |
sheAdslVccRDIAlarmRDI detected. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.27.4 |
sheAdslVccAISAlarmAIS detected. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.27.5 |
sheAdslVccTpConfigurationFailedNotification in case of failed VccTp-Configuration. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.27.6 |
sheAdslVccTpChangedEgressShapingATM egress shaping paramters were changed. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.27.7 |
sheAdslVccTpChangedIngressPolicingATM ingress policing paramters were changed. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.27.8 |
sheAdslVccTpAdminStateChangedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.27.9 |
sheAdslVccTpOrlChangedConfiguration trap. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.27.10 |
sheAdslVccTpUsedDslChannelChangedModification trap. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.27.11 |
sheAdslVccTpPerformanceCountersClearedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.27.12 |
sheAdslVccTpEncapsulationChangedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.27.13 |
sheAdslRfiBandTableThe RFI Band Table. SEQUENCE OF SheAdslRfiBandEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.29 |
sheAdslRfiBandEntryThis table contains RFI band configuration. For more details, refer ITU-T G.992.5 and ITU-T G.997.1. SheAdslRfiBandEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.29.1 |
sheAdslRfiBandIndexTable Index, automatically generated when the table is created. This is used as Bit mask index of sheAdslLineConfExtnProfileRfiBandMaskro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.29.1.1 |
sheAdslRfiBandNameA descriptional name for the RFI band. Special characters are not allowed, like: space : ?ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.29.1.2 |
sheAdslRfiBandStartToneThe start subcarrier index belonging to breakpoint:[ti;ti+1], corresponding to the low level of notch.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.29.1.3 |
sheAdslRfiBandStopToneThe stop subcarrier index belonging to breakpoint:[ti;ti+1], corresponding to the low level of notch.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.29.1.4 |
sheAdslRfiBandControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.30 |
sheAdslRfiBandControlRequestcreateAdslRfiBand: sheAdslRfiBandControlName sheAdslRfiBandControlStartTone sheAdslRfiBandControlStopTone deleteAdslRfiBand: sheAdslRfiBandControlIndexrw SheAdslControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.30.1 |
sheAdslRfiBandControlIndexIndex of the Table-entry to be configured.rw Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.30.2 |
sheAdslRfiBandControlStatusThe status of a user command.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.30.3 |
sheAdslRfiBandControlTimerThe maximum wait time for the manager for a long running user command.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.30.4 |
sheAdslRfiBandControlReqResultThe result of the last user command.ro SheAdslControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.30.5 |
sheAdslRfiBandControlTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.30.6 |
sheAdslRfiBandControlNameA descriptional name for the RFI band.rw OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.30.7 |
sheAdslRfiBandControlStartToneThe start subcarrier index belonging to breakpoint:[ti;ti+1], corresponding to the low level of notch.rw Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.30.8 |
sheAdslRfiBandControlStopToneThe stop subcarrier index belonging to breakpoint:[ti;ti+1], corresponding to the low level of notch.rw Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.30.9 |
sheAdslRfiBandNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.31 |
sheAdslRfiBandCreatedWhen an ADSL RFI Band is created, it occurs. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.31.1 |
sheAdslRfiBandDeletedWhen an ADSL RFI Band is removed, it occurs. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.31.2 |
sheAdslAtucPsdRefMasks OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.32 |
sheAdslAtucPsdRefMaskAdsl2AnnexA< PSD reference mask data format description > PSD mask can be described with a set of breakpoints. Breakpoint is a pair of tone index and PSD level. Number of maximum breakpoint is 32. All variable in this format is network byte order (big endian). < Data field of PSD reference mask > Breakpoint# tone index : tone index for breakpoint. Valid range is 1~255 for sheAdslAtucPsdRefMaskAdsl2AnnexA, sheAdslAtucPsdRefMaskAdsl2AnnexB and sheAdslAtucPsdRefMaskAnnexL, 1-511 for sheAdslAtucPsdRefMaskAdsl2plusAnnexA and sheAdslAtucPsdRefMaskAdsl2plusAnnexB. Breakpoint# PSD level : According to ITU-T G.997.1, the PSD maks level shall be coded as an unsigned integer represening PSD levels 0dBm/Hz (coded as 0) to -127.5 dBm/Hz (coded as 255), in the steps of 0.5dBm/Hz, with valid range 0 to -95dBm/Hz. So Valid value range is 0~190. Tone index of first breakpoint should be 1. Tone index of last valid breakpoint should be 255 in case of Adsl2AnnexA, Adsl2AnnexB, AnnexL. And should be 511 for Adsl2plusAnnexA, Adsl2plusAnnexB case Breakpoint should be alligned with increasing tone order. < PSD Reference mask data format (Maximum 128 bytes) > Breakpoint1 tone index (2bytes) Breakpoint1 PSD level (1bytes) Breakpoint2 tone index (2bytes) Breakpoint2 PSD level (1bytes) Breakpoint3 tone index (2bytes) Breakpoint3 PSD level (1bytes) Breakpoint32 tone index (2bytes) Breakpoint32 PSD level (1bytes)ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.32.1 |
sheAdslAtucPsdRefMaskAdsl2AnnexBRefer to the sheAdslAtucPsdRefMaskAdsl2AnnexA description.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.32.2 |
sheAdslAtucPsdRefMaskAdsl2plusAnnexARefer to the sheAdslAtucPsdRefMaskAdsl2AnnexA description.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.32.3 |
sheAdslAtucPsdRefMaskAdsl2plusAnnexBRefer to the sheAdslAtucPsdRefMaskAdsl2AnnexA description.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.32.4 |
sheAdslAtucPsdRefMaskAnnexLRefer to the sheAdslAtucPsdRefMaskAdsl2AnnexA descriptionro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.32.5 |
sheAdslAtucDualChanTableThis table provides one row for each ATUC channel. Only supported by NE R2.5 and higher. SEQUENCE OF SheAdslAtucDualChanEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.33 |
sheAdslAtucDualChanEntryAn entry in the adslAtucChanTable. New table only supported by NE releases up R2.5. Indexed by ifIndex - ChanType. SheAdslAtucDualChanEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.33.1 |
sheAdslAtucDualChanInterleaveDelayInterleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is Fast(125), use noSuchObject.ro Gauge32 UNITS "milli-seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.33.1.1 |
sheAdslAtucDualChanCurrTxRateActual transmit rate on this channel.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.33.1.2 |
sheAdslAtucDualChanPrevTxRateThe rate at the time of the last adslAtucRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAtucThresh(*)RateDown or less than adslAtucThresh(*)RateUp will not cause a trap or cause this object to change. (*) == Fast or Interleave. See AdslLineAlarmConfProfileEntry.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.33.1.3 |
sheAdslAtucDualChanCrcBlockLengthIndicates the length of the channel data-block on which the CRC operates. Refer to Line Code Specific MIBs, [11] and [12] for more information.ro Gauge32 UNITS "byte" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.33.1.4 |
sheAdslAtucDualChanCurrAtmStatusindicates an ncd or lcd failure if the counter surpasses 127. If neither ATM counter surpasses 127, the return value will be 'NoAtmDefect'. noAtmDefect(0), noCellDeleniation(1), lossOfCellDeleniation(2)ro SheAdslLineAtmStatus .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.33.1.5 |
sheAdslAtucDualChanRsSymbolsIndicates number of DMT symbols per Reed-Solomon code word (S) in the downstream direction. Note that S is not restricted to interleaved mode only. Even in fast mode, S is a valid constant value and is equal to 1.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.33.1.6 |
sheAdslAtucDualChanRsDepthIndicates interleaving depth (D) in the downstream direction. Note that D is not restricted to interleaved mode only. Even in fast mode, D is a valid constant value and is equal to 1.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.33.1.7 |
sheAdslAtucDualChanRsRedundancyIndicates number of redundant bytes (R) per Reed-Solomon code in the downstream direction.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.33.1.8 |
sheAdslAtucDualChanTypeExplains the type of channel entry interleaved or fast! (1) interleaved channel (2) fast channelro SheAdslChannelType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.33.1.9 |
sheAdslAturDualChanTableThis table provides one row for each ATUR channel. Only supported by NE R2.5 and higher. SEQUENCE OF SheAdslAturDualChanEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.34 |
sheAdslAturDualChanEntryAn entry in the adslAturChanTable. New table only supported by NE releases up R2.5. Indexed by ifIndex - ChanType. SheAdslAturDualChanEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.34.1 |
sheAdslAturDualChanInterleaveDelayInterleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is Fast(125), use noSuchObject.ro Gauge32 UNITS "milli-seconds" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.34.1.1 |
sheAdslAturDualChanCurrTxRateActual transmit rate on this channel.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.34.1.2 |
sheAdslAturDualChanPrevTxRateThe rate at the time of the last adslAturRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAturThresh(*)RateDown or less than adslAturThresh(*)RateUp will not cause a trap or cause this object to change. (*) == Fast or Interleave. See AdslLineAlarmConfProfileEntry.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.34.1.3 |
sheAdslAturDualChanCrcBlockLengthIndicates the length of the channel data-block on which the CRC operates. Refer to Line Code Specific MIBs, [11] and [12] for more information.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.34.1.4 |
sheAdslAturDualChanCurrAtmStatusThis object indicates an ncd or lcd failure if the counter surpasses 127. If neither ATM counter surpasses 127, the return value will be NoAtmDefect. noAtmDefect(0), noCellDeleniation(1), lossOfCellDeleniation(2)ro SheAdslLineAtmStatus .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.34.1.5 |
sheAdslAturDualChanRsSymbolsThis object indicates number of DMT symbols per Reed- Solomon code word (S) in the upstream direction Note that S is not restricted to interleaved mode only. Even in fast mode, S is a valid constant value and is equal to 1.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.34.1.6 |
sheAdslAturDualChanRsDepthThis object indicates interleaving depth (D) in the upstream direction Note that D is not restricted to interleaved mode only. Even in fast mode, D is a valid constant value and is equal to 1.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.34.1.7 |
sheAdslAturDualChanRsRedundancyThis object indicates number of redundant bytes (R) per Reed-Solomon code in the upstream direction.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.34.1.8 |
sheAdslAturDualChanTypeExplains the type of channel entry interleaved or fast! (1) interleaved channel (2) fast channelro SheAdslChannelType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.34.1.9 |
sheAdslAtucDualChanPerfDataTableThis table provides one row for each ATUC channel. Only supported by NE R2.5 and higher. SEQUENCE OF SheAdslAtucDualChanPerfDataEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35 |
sheAdslAtucDualChanPerfDataEntryAn entry in adslAtucChanPerfDataTable. New table only supported by NE releases up R2.5. Indexed by ifIndex - ChanType. SheAdslAtucDualChanPerfDataEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1 |
sheAdslAtucDualChanPerfDataTimeElapsedTotal elapsed seconds in this interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.1 |
sheAdslAtucDualChanPerfDataReceivedBlksCount of all encoded blocks received on this channel since agent reset.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.2 |
sheAdslAtucDualChanPerfDataTransmittedBlksCount of all encoded blocks transmitted on this channel since agent reset.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.3 |
sheAdslAtucDualChanPerfDataCorrectedBlksCount of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.4 |
sheAdslAtucDualChanPerfDataUncorrectBlksCount of all blocks received with uncorrectable errors since agent reset.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.5 |
sheAdslAtucDualChanPerfDataNcdCount of no cell delineation(ncd) on this channel.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.6 |
sheAdslAtucDualChanPerfDataOcdCount of out of cell delineation (ocd) on this channel.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.7 |
sheAdslAtucDualChanPerfDataHecHeader error check counter(hec) on this channel.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.8 |
sheAdslAtucDualChanPerfDataValidIntervalsThe number of previous 15-minute intervals in the interval table for which data was collected. Given that <n> is the maximum # of intervals supported. The value will be <n> unless the measurement was (re-)started within the last (<n>*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.9 |
sheAdslAtucDualChanPerfDataInvalidIntervalsThe number of intervals in the range from 0 to the value of adslAtucChanPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.10 |
sheAdslAtucDualChanPerfDataCurr15MinTimeElapsedTotal elapsed seconds in this interval.ro AdslPerfTimeElapsed .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.11 |
sheAdslAtucDualChanPerfDataCurr15MinReceivedBlksCount of all encoded blocks received on this channel within the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.12 |
sheAdslAtucDualChanPerfDataCurr15MinTransmittedBlksCount of all encoded blocks transmitted on this channel within the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.13 |
sheAdslAtucDualChanPerfDataCurr15MinCorrectedBlksCount of all blocks received with errors that were corrected on this channel within the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.14 |
sheAdslAtucDualChanPerfDataCurr15MinUncorrectBlksCount of all blocks received with uncorrectable errors on this channel within the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.15 |
sheAdslAtucDualChanPerfDataCurr15MinNcdCount of no cell delineation(ncd) on this channel within the current 15 minute time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.16 |
sheAdslAtucDualChanPerfDataCurr15MinOcdCount of out of cell delineation (ocd) on this channel within the current 15 minute time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.17 |
sheAdslAtucDualChanPerfDataCurr15MinHecHeader error check counter(hec) on this channel within the current 15 minute time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.18 |
sheAdslAtucDualChanPerfDataCurr1DayTimeElapsedNumber of seconds that have elapsed since the beginning of the current 1-day interval.ro AdslPerfTimeElapsed .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.19 |
sheAdslAtucDualChanPerfDataCurr1DayReceivedBlksCount of all encoded blocks received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.20 |
sheAdslAtucDualChanPerfDataCurr1DayTransmittedBlksCount of all encoded blocks transmitted on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.21 |
sheAdslAtucDualChanPerfDataCurr1DayCorrectedBlksCount of all blocks received with errors that were corrected on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.22 |
sheAdslAtucDualChanPerfDataCurr1DayUncorrectBlksCount of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.23 |
sheAdslAtucDualChanPerfDataCurr1DayNcdCount of no cell delineation (ncd) on this channel within the current 1 day time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.24 |
sheAdslAtucDualChanPerfDataCurr1DayOcdCount of out of cell delineation (ocd) on this channel within the current 1 day time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.25 |
sheAdslAtucDualChanPerfDataCurr1DayHecHeader error check counter (hec) on this channel within the current 1 day time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.26 |
sheAdslAtucDualChanPerfDataPrev1DayMoniSecsThe amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.27 |
sheAdslAtucDualChanPerfDataPrev1DayReceivedBlksCount of all encoded blocks received on this channel within the most recent previous 1-day period.ro AdslPerfPrevDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.28 |
sheAdslAtucDualChanPerfDataPrev1DayTransmittedBlksCount of all encoded blocks transmitted on this channel within the most recent previous 1-day period.ro AdslPerfPrevDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.29 |
sheAdslAtucDualChanPerfDataPrev1DayCorrectedBlksCount of all blocks received with errors that were corrected on this channel within the most recent previous 1-day period.ro AdslPerfPrevDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.30 |
sheAdslAtucDualChanPerfDataPrev1DayUncorrectBlksCount of all blocks received with uncorrectable errors on this channel within the most recent previous 1-day period.ro AdslPerfPrevDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.31 |
sheAdslAtucDualChanPerfDataPrev1DayNcdCount of no cell delineation (ncd) on this channel within the most recent previous 1-day period.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.32 |
sheAdslAtucDualChanPerfDataPrev1DayOcdCount of out of cell delineation (ocd) on this channel within the most recent previous 1-day period.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.33 |
sheAdslAtucDualChanPerfDataPrev1DayHecHeader error check counter(hec) on this channel within the most recent previous 1-day period.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.35.1.34 |
sheAdslAturDualChanPerfDataTableThis table provides one row for each ATUR channel. Only supported by NE R2.5 and higher. SEQUENCE OF SheAdslAturDualChanPerfDataEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36 |
sheAdslAturDualChanPerfDataEntryAn entry in adslAturChanPerfDataTable. New table only supported by NE releases up R2.5. Indexed by ifIndex - ChanType. SheAdslAturDualChanPerfDataEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1 |
sheAdslAturDualChanPerfDataReceivedBlksCount of all encoded blocks received on this channel since agent reset.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.1 |
sheAdslAturDualChanPerfDataTransmittedBlksCount of all encoded blocks transmitted on this channel since agent reset.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.2 |
sheAdslAturDualChanPerfDataCorrectedBlksCount of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.3 |
sheAdslAturDualChanPerfDataUncorrectBlksCount of all blocks received with uncorrectable errors since agent reset.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.4 |
sheAdslAturDualChanPerfDataExtnNcdNumber of packets with no cell delineation(NCD) error on this channel.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.5 |
sheAdslAturDualChanPerfDataExtnHecNumber of packets with Header error check (HEC) error on this channel.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.6 |
sheAdslAturDualChanPerfDataPerfValidIntervalsThe number of previous 15-minute intervals in the interval table for which data was collected. Given that <n> is the maximum # of intervals supported. The value will be <n> unless the measurement was (re-)started within the last (<n>*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.7 |
sheAdslAturDualChanPerfDataPerfInvalidIntervalsThe number of intervals in the range from 0 to the value of adslAturChanPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.8 |
sheAdslAturDualChanPerfDataCurr15MinTimeElapsedTotal elapsed seconds in this interval. A full interval is 900 seconds.ro AdslPerfTimeElapsed .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.9 |
sheAdslAturDualChanPerfDataCurr15MinReceivedBlksCount of all encoded blocks received on this channel within the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.10 |
sheAdslAturDualChanPerfDataCurr15MinTransmittedBlksCount of all encoded blocks transmitted on this channel within the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.11 |
sheAdslAturDualChanPerfDataCurr15MinCorrectedBlksCount of all blocks received with errors that were corrected on this channel within the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.12 |
sheAdslAturDualChanPerfDataCurr15MinUncorrectBlksCount of all blocks received with uncorrectable errors on this channel within the current 15 minute interval.ro PerfCurrentCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.13 |
sheAdslAturDualChanPerfDataExtnCurr15MinNcdNumber of packets with no cell delineation(NCD) error on this channel within the current 15 minute time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.14 |
sheAdslAturDualChanPerfDataExtnCurr15MinHecNumber of packets with Header error check (HEC) error on this channel within the current 15 minute time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.15 |
sheAdslAturDualChanPerfDataCurr1DayTimeElapsedNumber of seconds that have elapsed since the beginning of the current 1-day interval.ro AdslPerfTimeElapsed .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.16 |
sheAdslAturDualChanPerfDataCurr1DayReceivedBlksCount of all encoded blocks received on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.17 |
sheAdslAturDualChanPerfDataCurr1DayTransmittedBlksCount of all encoded blocks transmitted on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.18 |
sheAdslAturDualChanPerfDataCurr1DayCorrectedBlksCount of all blocks received with errors that were corrected on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.19 |
sheAdslAturDualChanPerfDataCurr1DayUncorrectBlksCount of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.ro AdslPerfCurrDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.20 |
sheAdslAturDualChanPerfDataExtnCurr1DayNcdNumber of packets with no cell delineation (NCD) error on this channel within the current 1 day time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.21 |
sheAdslAturDualChanPerfDataExtnCurr1DayHecNumber of packets with Header error check (HEC) error on this channel within the current 1 day time interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.22 |
sheAdslAturDualChanPerfDataPrev1DayMoniSecsThe amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.23 |
sheAdslAturDualChanPerfDataPrev1DayReceivedBlksCount of all encoded blocks received on this channel within the most recent previous 1-day period.ro AdslPerfPrevDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.24 |
sheAdslAturDualChanPerfDataPrev1DayTransmittedBlksCount of all encoded blocks transmitted on this channel within the most recent previous 1-day period.ro AdslPerfPrevDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.25 |
sheAdslAturDualChanPerfDataPrev1DayCorrectedBlksCount of all blocks received with errors that were corrected on this channel within the most recent previous 1-day period.ro AdslPerfPrevDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.26 |
sheAdslAturDualChanPerfDataPrev1DayUncorrectBlksCount of all blocks received with uncorrectable errors on this channel within the most recent previous 1-day period.ro AdslPerfPrevDayCount (ADSL-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.27 |
sheAdslAturDualChanPerfDataExtnPrev1DayNcdNumber of packets with no cell delineation (NCD) error on this channel within the most recent previous period.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.28 |
sheAdslAturDualChanPerfDataExtnPrev1DayHecNumber of packets with Header error check (HEC) error on this channel within the most recent previous period.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.36.1.29 |
sheAdslAtucDualChanIntervalTableThis table provides one row for each ATUC channel's performance data collection interval. Only supported by NE R2.5 and higher. SEQUENCE OF SheAdslAtucDualChanIntervalEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.37 |
sheAdslAtucDualChanIntervalEntryAn entry in the adslAtucIntervalTable. New table only supported by NE releases up R2.5. Indexed by ifIndex - ChanType - IntervalNumber. SheAdslAtucDualChanIntervalEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.37.1 |
sheAdslAtucDualChanIntervalNumberPerformance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.37.1.1 |
sheAdslAtucDualChanIntervalValidDataThis variable indicates if the data for this interval is valid.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.37.1.2 |
sheAdslAtucDualChanIntervalEndTimeThis variable indicates the time of storing this interval.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.37.1.3 |
sheAdslAtucDualChanIntervalReceivedBlksCount of all encoded blocks received on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.37.1.4 |
sheAdslAtucDualChanIntervalTransmittedBlksCount of all encoded blocks transmitted on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.37.1.5 |
sheAdslAtucDualChanIntervalCorrectedBlksCount of all blocks received with errors that were corrected on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.37.1.6 |
sheAdslAtucDualChanIntervalUncorrectBlksCount of all blocks received with uncorrectable errors on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.37.1.7 |
sheAdslAtucDualChanIntervalNcdIndicates count of no cell delineation on this channel for this interval.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.37.1.8 |
sheAdslAtucDualChanIntervalOcdIndicates count of out cell delineation on this channel for this interval.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.37.1.9 |
sheAdslAtucDualChanIntervalHecIndicates Header error check counter on this channel during this interval.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.37.1.10 |
sheAdslAturDualChanIntervalTableThis table provides one row for each ATUR channel's performance data collection interval. Only supported by NE R2.5 and higher. SEQUENCE OF SheAdslAturDualChanIntervalEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.38 |
sheAdslAturDualChanIntervalEntryAn entry in the adslAturIntervalTable. New table only supported by NE releases up R2.5. Indexed by ifIndex - ChanType - IntervalNumber. SheAdslAturDualChanIntervalEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.38.1 |
sheAdslAturDualChanIntervalNumberPerformance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.38.1.1 |
sheAdslAturDualChanIntervalValidDataThis variable indicates if the data for this interval is valid.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.38.1.2 |
sheAdslAturDualChanIntervalEndTimeThis variable indicates the time of storing this interval.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.38.1.3 |
sheAdslAturDualChanIntervalReceivedBlksCount of all encoded blocks received on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.38.1.4 |
sheAdslAturDualChanIntervalTransmittedBlksCount of all encoded blocks transmitted on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.38.1.5 |
sheAdslAturDualChanIntervalCorrectedBlksCount of all blocks received with errors that were corrected on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.38.1.6 |
sheAdslAturDualChanIntervalUncorrectBlksCount of all blocks received with uncorrectable errors on this channel during this interval.ro PerfIntervalCount (PerfHist-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.38.1.7 |
sheAdslAturDualChanIntervalNcdIndicates count of no cell delineation on this channel for this interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.38.1.8 |
sheAdslAturDualChanIntervalHecIndicates Header error check counter on this channel during this interval.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.38.1.9 |
sheAdslLineDpboProfileTableThe Dpbo Profile Table. Support with SHE R2.6 RP2. SEQUENCE OF SheAdslLineDpboProfileEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.39 |
sheAdslLineDpboProfileEntryThis table contains DPBO profile configuration. For more details, refer ITU-T G.997.1 chapter 7.3.1.2.13. SheAdslLineDpboProfileEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.39.1 |
sheAdslLineDpboProfileIndexTable Index, automatically generated when the table entry is created.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.39.1.1 |
sheAdslLineDpboProfileNameThis object is used by the line configuration table in order to identify a row of this table for Dpbo profile assign. Special characters are not allowed, like: space : ?ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.39.1.2 |
sheAdslLineDpboProfileEselThis configuration parameter defines the assumed electrical length of cables (E-side cables) connecting exchange based DSL services to a remote flexibility point (cabinet), that may also host remotely located DSL that is subject to spectrally shaped downstream power backoff depending on this length. For this parameter the electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency defined by the network operator or in spectrum management regulations. All values which can be represented by the format are valid values. If this value is zero, the DPBO in this section shall be disabled. If this value is not zero and sheAdslLineDpboProfileEselMin is not 512 (disabled EselMin), sheAdslLineDpboProfileEsel >= sheAdslLineDpboProfileEselMin is required!ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.39.1.3 |
sheAdslLineDpboProfileEselMinThis configuration parameter defines the minimum assumed electrical length of cables (E-side cables) connecting exchange based DSL services to a remote flexibility point (cabinet), that may also host remotely located DSL that is subject to spectrally shaped downstream power backoff depending on this length. For this parameter the electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency defined by the network operator or in spectrum management regulations. All values which can be represented by the format are valid values. Default: sheAdslLineDpboProfileEselMin = 512 If this value is not 512 (disabled) and sheAdslLineDpboProfileEsel is not zero (DPBO disabled), sheAdslLineDpboProfileEsel >= sheAdslLineDpboProfileEselMin is required!ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.39.1.4 |
sheAdslLineDpboProfileMusDPBOMUS defines the assumed Minimum Usable receive Signal PSD (in dBm/Hz) for exchange based services, used to modify parameter DPBOFMAX defined below. All values which can be represented by the format are valid values: 0 = 0 dBm/Hz .. -127.5 dBm/Hz (coded as 255).ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.39.1.5 |
sheAdslLineDpboProfileMofDPBOMOF (mask overall floor) defines the absolut minimum of the used PSD mask (in dBm/Hz) for exchange based services. All values which can be represented by the format are valid values: 0 = 0 dBm/Hz .. -127.5 dBm/Hz (coded as 255). Note: Not longer supported!ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.39.1.6 |
sheAdslLineDpboProfileFMinDPBO shall be applied in the range starting at DPBOFMIN and should be configured as an subcarrier index. The range of valid values is from 1 to 512.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.39.1.7 |
sheAdslLineDpboProfileFMaxThe maximum subcarrier at which DPBO may be applied is DPBOFMAX. The range of valid values is from 1 to 512.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.39.1.8 |
sheAdslLineDpboProfileEpsdUsed PSD mask that is assumed to be permitted at the exchange. The set of breakpoints can be represented as [(t1, PSD1),(t2, PSD2), .. , (tN, PSDN)]. The subcarrier index (tN) shall be coded as an unsigned integer (16 bit, range 1..512). The MIB PSD mask level (PSDN) shall be coded as an unsigned integer (16 bit) representing the MIB PSD mask levels 0 dBm/Hz (coded as 0) to -127.5 dBm/Hz (coded as 255), in steps of 0.5 dBm/Hz. The maximum number of breakpoints for DPBOEPSD is 16. If less then maximum breakpoints will be defined, all used breakpoints should be configured in a consecutive way without spaces (t1 - t2 - t3.. and not t1 - t5 - t7..). The default value should be set according PSD settings for ADSL2+. Subcarrier PSD 59 -36.5 256 -36.5 314 -42 376 -46.5 499 -47.5ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.39.1.9 |
sheAdslLineDpboProfileEScmAThis configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that are used to estimate the frequency dependent loss of E-side cables calculated from the DPBOESEL parameter using the formula: ESCM(f) = (DPBOESCMA + DPBOESCMB*sqrt(f) + DPBOESCMC*f )*DPBOESCL Where ESCM is expressed in dB and f is expressed in MHz. DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 2^-8. All values are valid.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.39.1.10 |
sheAdslLineDpboProfileEScmBThis configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that are used to estimate the frequency dependent loss of E-side cables calculated from the DPBOESEL parameter using the formula: ESCM(f) = (DPBOESCMA + DPBOESCMB*sqrt(f) + DPBOESCMC*f )*DPBOESCL Where ESCM is expressed in dB and f is expressed in MHz. DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 2^-8. All values are valid.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.39.1.11 |
sheAdslLineDpboProfileEScmCThis configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that are used to estimate the frequency dependent loss of E-side cables calculated from the DPBOESEL parameter using the formula: ESCM(f) = (DPBOESCMA + DPBOESCMB*sqrt(f) + DPBOESCMC*f )*DPBOESCL Where ESCM is expressed in dB and f is expressed in MHz. DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 2^-8. All values are valid.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.39.1.12 |
sheAdslLineDpboProfileControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40 |
sheAdslLineDpboProfileControlRequestcreateAdslLineDpboProfile: sheAdslLineDpboProfileControlName sheAdslLineDpboProfileControlEsel sheAdslLineDpboProfileControlEselMin sheAdslLineDpboProfileControlMus sheAdslLineDpboProfileControlMof sheAdslLineDpboProfileControlFMin sheAdslLineDpboProfileControlFMax sheAdslLineDpboProfileControlEpsd sheAdslLineDpboProfileControlEScmA sheAdslLineDpboProfileControlEScmB sheAdslLineDpboProfileControlEScmC modifyAdslLineDpboProfile: sheAdslLineDpboProfileControlIndex sheAdslLineDpboProfileControlEsel sheAdslLineDpboProfileControlEselMin sheAdslLineDpboProfileControlMus sheAdslLineDpboProfileControlMof sheAdslLineDpboProfileControlFMin sheAdslLineDpboProfileControlFMax sheAdslLineDpboProfileControlEpsd sheAdslLineDpboProfileControlEScmA sheAdslLineDpboProfileControlEScmB sheAdslLineDpboProfileControlEScmC deleteAdslLineDpboProfile sheAdslLineDpboProfileControlIndexrw SheAdslControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40.1 |
sheAdslLineDpboProfileControlIndexIndex of the Table-entry to be configured.rw Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40.2 |
sheAdslLineDpboProfileControlStatusThe status of a user command.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40.3 |
sheAdslLineDpboProfileControlTimerThe maximum wait time for the manager for a long running user command.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40.4 |
sheAdslLineDpboProfileControlReqResultThe result of the last user command.ro SheAdslControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40.5 |
sheAdslLineDpboProfileControlTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40.6 |
sheAdslLineDpboProfileControlNameA descriptional name for the Dpbo profile.rw OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40.7 |
sheAdslLineDpboProfileControlEsellook at tablerw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40.8 |
sheAdslLineDpboProfileControlEselMinlook at tablerw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40.9 |
sheAdslLineDpboProfileControlMuslook at tablerw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40.10 |
sheAdslLineDpboProfileControlMoflook at table Note: Not longer supported!rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40.11 |
sheAdslLineDpboProfileControlFMinlook at tablerw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40.12 |
sheAdslLineDpboProfileControlFMaxlook at tablerw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40.13 |
sheAdslLineDpboProfileControlEpsdlook at table.rw OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40.14 |
sheAdslLineDpboProfileControlEScmAlook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40.15 |
sheAdslLineDpboProfileControlEScmBlook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40.16 |
sheAdslLineDpboProfileControlEScmClook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.40.17 |
sheAdslVccTpPerformanceTableThe VccTpPerformance-Table. SEQUENCE OF SheAdslVccTpPerformanceEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.41 |
sheAdslVccTpPerformanceEntryThis table contains the VccTpPerformance-Counters. These are free running counters. The counters could be deleted with command deleteAdslVccTpPerformanceCounters via sheAdslVccTpControl-Group. SheAdslVccTpPerformanceEntry .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.41.1 |
sheAdslVccTpIngressUnicastPacketsIngress Unicast Packet Counter for this VccTp.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.41.1.1 |
sheAdslVccTpIngressMulticastPacketsIngress Multicast Packet Counter for this VccTp.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.41.1.2 |
sheAdslVccTpIngressBroadcastPacketsIngress Broadcast Packet Counter for this VccTp.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.41.1.3 |
sheAdslVccTpIngressDiscardPacketsIngress Discard Packet Counter for this VccTp.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.41.1.4 |
sheAdslVccTpEgressUnicastPacketsEgress Unicast Packet Counter for this VccTp.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.41.1.5 |
sheAdslVccTpEgressMulticastPacketsEgress Multicast Packet Counter for this VccTp.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.41.1.6 |
sheAdslVccTpEgressBroadcastPacketsEgress Broadcast Packet Counter for this VccTp.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.41.1.7 |
sheAdslVccTpEgressDiscardPacketsEgress Discard Packet Counter for this VccTp.ro Counter32 .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.41.1.8 |
sheAdslConformance OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.100 |
sheAdslCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.100.1 |
sheAdslComplianceDescription. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.100.1.1 |
sheAdslGroups OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.100.2 |
sheAdslVccTpGroupDescription. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.100.2.1 |
sheAdslVccTpControlGroupDescription. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.100.2.2 |
sheAdslVccTpNotificationGroupDescription. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.100.2.3 |
sheAdslGroupDescription. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.100.2.4 |
sheAdslControlGroupDescription. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.100.2.5 |
sheAdslNotificationGroupDescription. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.100.2.6 |
sheAdslDualChanGroupDescription. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.100.2.7 |
sheAdslObsoleteGroupDescription. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.100.2.9 |
sheAdslObsoleteNotificationGroupDescription. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.6.1.1.100.2.10 |