VERILINK-ENTERPRISE-NCMIMUX-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
51
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
51 total| Object Name |
|---|
RFC1213-MIBThe IMUX Configuration table. Unknown .1.3.6.1.4.1.321.1.3030.7000 |
ncmimuxStatusTableThe IMUX Status table. SEQUENCE OF NcmimuxStatusEntry .1.3.6.1.4.1.321.1.3030.7001 |
ncmimuxStatusEntryAn entry in the IMUX Status table. NcmimuxStatusEntry .1.3.6.1.4.1.321.1.3030.7001.1 |
ncmimuxNIDStatusIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3030.7001.1.1 |
ncmimuxStatusIndexThis object is the identifier of a Inter-
face on a managed device. If there is an ifEn-
try that is directly associated with this it
should have the same value as ifIndex. Otherwise,
the value exceeds ifNumber, and is a unique
identifier following this rule: inside interfaces (e.g.,
equipment side) with even numbers and outside
interfaces (e.g., network side) with odd
numbers.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3030.7001.1.2 |
ncmimuxStatEndIdThis value for this object indicates which
end of the equipment it is accessing.ro Enumeration .1.3.6.1.4.1.321.1.3030.7001.1.3 |
ncmimuxLinesEqpThis variable indicates the inverse multiplexer
carrier lines equipped. One bit per line. Here each
bit in this byte represents one of the eight carrier
lines that may be used by the Imux. Bit zero represents
carrierline number one, and bit seven represents
carrier line number eight. For each bit that is set
to one, the corresponding carrier line will be configured
for use by the ncmimux. For each bit that is set to zero,
the corresponding carrier line will be excluded from the
ncmimux configuration i.e., 1 = 0000 0001(bin). The range
for this variable is from (in decimals 0 to 256).ro DisplayString .1.3.6.1.4.1.321.1.3030.7001.1.4 |
ncmimuxLinesStatThis represents the lines active equivalent in tabs message,
indicating when a carrier line has been allocated for use
by the ncmimux. (Loop integrity must be established before the
line can be put into active service).Options supported
active, inactive or none.ro DisplayString .1.3.6.1.4.1.321.1.3030.7001.1.5 |
ncmimuxFrameStatusThis variable indicates the ncmimux frame structure is transmitted over
each carrier line that has been allocated for use by the ncmimux. This
field indicates that this frame structure has been recongnized and
validated in the signal received on the carrier line or invalidated.ro DisplayString .1.3.6.1.4.1.321.1.3030.7001.1.6 |
ncmimuxCTSStatusThis variable indicates Clear To Send status that is encoded into
the ncmimux frame structure on each carrier line to indicate that the
integrity of the incoming signal has been validated. 'validCTS'
refers to Clear To Send indication has been detected in the
receive signal on the corresponding carrier line. 'invalidCTS'
refers to Clear To send has not been detected. 'none' represents
to not supportedro DisplayString .1.3.6.1.4.1.321.1.3030.7001.1.7 |
ncmimuxCRCStatusThis variable represents the crc error of the incoming frame
structure corresponding to a Carrier Line.ro DisplayString .1.3.6.1.4.1.321.1.3030.7001.1.8 |
ncmimuxFarEndCRCStatusThis variable represents the crc error of the incoming frame
structure received at the far end of the corresponding
Carrier Lines.ro DisplayString .1.3.6.1.4.1.321.1.3030.7001.1.9 |
ncmimuxDataValidStatusThis variable represents the data valid of the
Carrier Lines.ro DisplayString .1.3.6.1.4.1.321.1.3030.7001.1.10 |
ncmimuxNetworkAlarmThe value for this object indicates the front
panel LED alarm status for the network interface.ro Enumeration .1.3.6.1.4.1.321.1.3030.7001.1.11 |
ncmimuxAlarmLEDThe value for this object indicates the front
panel LED alarm status for the IMux.ro Enumeration .1.3.6.1.4.1.321.1.3030.7001.1.12 |
ncmimuxEventMessagesThe value for this object indicates the number
of event messages in the event queue. The event queue
is a list of state changes which are time-stamped and
recorded.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3030.7001.1.13 |
ncmimuxControlTableThe IMUX Control table. SEQUENCE OF NcmimuxControlEntry .1.3.6.1.4.1.321.1.3030.7002 |
ncmimuxControlEntryAn entry in the IMUX Control table. NcmimuxControlEntry .1.3.6.1.4.1.321.1.3030.7002.1 |
ncmimuxNIDControlIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3030.7002.1.1 |
ncmimuxControlIndexThis object is the identifier of a Inter-
face on a managed device. If there is an ifEn-
try that is directly associated with this it
should have the same value as ifIndex. Otherwise,
the value exceeds ifNumber, and is a unique
identifier following this rule: inside interfaces (e.g.,
equipment side) with even numbers and outside
interfaces (e.g., network side) with odd
numbers.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3030.7002.1.2 |
ncmimuxCntEndIdThis value for this object indicates which
end of the equipment it is accessing.ro Enumeration .1.3.6.1.4.1.321.1.3030.7002.1.3 |
ncmimuxLoopbackThis variable represents the Loopback status of Imux,
ELB or PLB i.e., Equipment Loop back or Payload loop
back.rw Enumeration .1.3.6.1.4.1.321.1.3030.7002.1.4 |
ncmimuxAISPatternThis refers to the AIS test pattern initiatedrw Enumeration .1.3.6.1.4.1.321.1.3030.7002.1.5 |
ncmimuxTestPatternThis refers to the test pattern initiatedro Enumeration .1.3.6.1.4.1.321.1.3030.7002.1.6 |
ncmimuxDTEStatTableThe IMUX DTE Status table. SEQUENCE OF NcmimuxDTEStatEntry .1.3.6.1.4.1.321.1.3030.7003 |
ncmimuxDTEStatEntryAn entry in the IMUX DTEStatus table. NcmimuxDTEStatEntry .1.3.6.1.4.1.321.1.3030.7003.1 |
ncmimuxNIDDTEStatIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3030.7003.1.1 |
ncmimuxDTEStatIndexThis object is the identifier of a Inter-
face on a managed device. If there is an ifEn-
try that is directly associated with this it
should have the same value as ifIndex. Otherwise,
the value exceeds ifNumber, and is a unique
identifier following this rule: inside interfaces (e.g.,
equipment side) with even numbers and outside
interfaces (e.g., network side) with odd
numbers.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3030.7003.1.2 |
ncmimuxDTEStatRegThis object reports the contents of the DTE
Status Register as read from the IMUX hardware.ro Enumeration .1.3.6.1.4.1.321.1.3030.7003.1.3 |
ncmimuxDTEStatLPBKThis object reports the DTE Pattern and Loopback
Code Register Status. (0) indicates that a Loop Up
Code was detected. (1) indicates that Data Pattern
or Loop Up Code errors were detected. (2) indicates
a Loop Down Code was detected. (3) indicates Loop Down
Code Errors were detected. (4) indicates PRBS 2 x 10^25
Aggregate Data Bandwidth.ro Enumeration .1.3.6.1.4.1.321.1.3030.7003.1.4 |
ncmimuxDTEStatAlarmThis object reports the front panel alarm LED status for
the DTE interface.ro Enumeration .1.3.6.1.4.1.321.1.3030.7003.1.5 |
ncmimuxConfigEntryAn entry in the ncm IMUX Configuration table. NcmimuxConfigEntry .ncmimuxConfigTable.1 |
ncmimuxNIDConfigIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .ncmimuxConfigTable.1.1 |
ncmimuxLineIndexThis object is the identifier of a Inter-
face on a managed device. If there is an ifEn-
try that is directly associated with this it
should have the same value as ifIndex. Otherwise,
the value exceeds ifNumber, and is a unique
identifier following this rule: inside interfaces (e.g.,
equipment side) with even numbers and outside
interfaces (e.g., network side) with odd
numbers.ro INTEGER (1..'7fffffff'h) .ncmimuxConfigTable.1.2 |
ncmimuxEndIdThis value for this object indicates which
end of the equipment it is accessing.ro Enumeration .ncmimuxConfigTable.1.3 |
ncmimuxIfIndexThis value for this object is equal to the
value of ifIndex from the Interfaces table of
MIB II (RFC 1213).ro INTEGER (1..'7fffffff'h) .ncmimuxConfigTable.1.4 |
ncmimuxBkplaneBusSelectThis object only has signifiance for IMUX 2164.
This variable specifies which IMUX line(s) is used,
and which backplane bus is assigned to which line(s).
The pattern of the the word is compsed as :-
line# 8 7 6 5 4 3 2 1
bus # bus-B B D D B B D D(8)
means lines 1,2,5,6 use bus - B
lines 3,4,7,8 use bus - D
The 'X' means no bus selection has been made.rw Enumeration .ncmimuxConfigTable.1.5 |
ncmimuxCarrierLineRateThis variable specifies whether the carrier line rate is T1 or
carrier line is E1.rw Enumeration .ncmimuxConfigTable.1.6 |
ncmimuxCarrierLinesEqpThis variable indicates the inverse multiplexer
carrier lines equipped. One bit per line. Here each
bit in this byte represents one of the eight carrier
lines that may be used by the Imux. Bit zero represents
carrierline number one, and bit seven represents
carrier line number eight. For each bit that is set
to one, the corresponding carrier line will be configured
for use by the ncmimux. For each bit that is set to zero,
the corresponding carrier line will be excluded from the
ncmimux configuration i.e., 1 = 0000 0001(bin). The range
for this variable is from (in decimals 0 to 256).rw DisplayString .ncmimuxConfigTable.1.7 |
ncmimuxChannelingThis variable indicates the inverse multiplexer mode
for T1 which by default is set to 64 Kbps and when the
field is set to (1) the 56 kbps mode is selected.rw Enumeration .ncmimuxConfigTable.1.8 |
ncmimuxDTEClkTransmitThis field request to determine the DTE data port clock
phase is normal or inverted. 'Normal' refers to inverse
multiplexer DTE clock phase is normal. 'Inverted' refers
to inverse multiplexer DTE clock phase is inverted.rw Enumeration .ncmimuxConfigTable.1.9 |
ncmimuxDTEClkRecvThis field request to determine the DTE data port clock
phase is normal or inverted. 'Normal' refers to inverse
multiplexer DTE clock phase is normal. 'Inverted' refers
to inverse multiplexer DTE clock phase is inverted.rw Enumeration .ncmimuxConfigTable.1.10 |
ncmimuxDTEClkRefernThis field request to determine the DTE data port clock
phase is normal or inverted. 'Normal' refers to inverse
multiplexer DTE clock phase is normal. 'Inverted' refers
to inverse multiplexer DTE clock phase is inverted.rw Enumeration .ncmimuxConfigTable.1.11 |
ncmimuxDTEModeThis variable represents the DTE mode of the ncmimuxrw Enumeration .ncmimuxConfigTable.1.12 |
ncmimuxDSRThis variable represents Data Set Ready for the ncmimux which
could be set for all interfaces.rw Enumeration .ncmimuxConfigTable.1.13 |
ncmimuxTMThis variable represents Test Mode for the ncmimux which
could be set for all interfaces.rw Enumeration .ncmimuxConfigTable.1.14 |
ncmimuxCTSThis variable represents Clear To Send for the ncmimux which
could be set for only V.35, EI530 and RS449 interfaces.rw Enumeration .ncmimuxConfigTable.1.15 |
ncmimuxDCDThis variable represents Data Carrier Detect for the ncmimux which
could be set for only V.35, EI530 and RS449 interfaces.rw Enumeration .ncmimuxConfigTable.1.16 |
ncmimuxRIThis variable represents Ring Indicator for the ncmimux which
could be set for only V.35 interfaces.rw Enumeration .ncmimuxConfigTable.1.17 |
ncmimuxSnapTypeThis variable represents the snap type for the ncmimuxro Enumeration .ncmimuxConfigTable.1.18 |
ncmimuxQuadSlotThis variable represents the DTE control mode of the ncmimuxrw INTEGER .ncmimuxConfigTable.1.19 |