VERILINK-ENTERPRISE-NCMGENERIC-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
764
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
764 total| Object Name |
|---|
RFC1213-MIB Unknown .1.3.6.1.4.1.321.1.3012.1001 |
ncmNodeInfoTable SEQUENCE OF NcmNodeInfoEntry .1.3.6.1.4.1.321.1.3012.1002 |
ncmNodeInfoEntryAn entry in the ncmNode Info table. NcmNodeInfoEntry .1.3.6.1.4.1.321.1.3012.1002.1 |
ncmNodeIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1002.1.1 |
ncmNodeAddressThis variable indicates the ncmNode Address.ro DisplayString -- .1.3.6.1.4.1.321.1.3012.1002.1.2 |
ncmTimeThe time (in the hh:mm:sec) format for the card.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.321.1.3012.1002.1.3 |
ncmDateThe date (in mm:dd:yy) format for the card.rw DisplayString .1.3.6.1.4.1.321.1.3012.1002.1.4 |
ncmNodeShelfThe variable indicates the bit mapping of shelf number
associated with the node the bit 1 if equipped and 0 if not
equipped. i.e. ncmShelf 0 = bit 0ro INTEGER .1.3.6.1.4.1.321.1.3012.1002.1.5 |
ncmNodeIDThe variable indicates the node id that uniquely identifies
a node.ro INTEGER .1.3.6.1.4.1.321.1.3012.1002.1.6 |
ncmControllerEqIDThe variable indicates the Equipment Id of the Controller.ro INTEGER .1.3.6.1.4.1.321.1.3012.1002.1.7 |
ncmShelfInfoTable SEQUENCE OF NcmShelfInfoEntry .1.3.6.1.4.1.321.1.3012.1003 |
ncmShelfInfoEntryAn entry in the ncmShelf Info table. NcmShelfInfoEntry .1.3.6.1.4.1.321.1.3012.1003.1 |
ncmShelfNIDIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1003.1.1 |
ncmShelfIndexThis object is the identifier of an Interface
on a managed device. If there is an ifEntry
that is directly associated with this and
only this DS1 interface, it should have the
same value as ifIndex. Otherwise, the value
exceeds ifNumber, and is a unique identifier
following this rule: inside interfaces (e.g.,
equipment side) with even numbers and outside
interfaces (e.g., network side) with odd
numbers.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1003.1.2 |
ncmShelfNumberThis variable indicates the number of the shelf.ro INTEGER .1.3.6.1.4.1.321.1.3012.1003.1.3 |
ncmShelfHardwareThis variable indicates the shelf hardware type.ro Enumeration .1.3.6.1.4.1.321.1.3012.1003.1.4 |
ncmNumberofCardsThis variable indicates the total number of cards in
the shelf.ro INTEGER .1.3.6.1.4.1.321.1.3012.1003.1.5 |
ncmListCardsInShelfThis variable indicates the cards present in the shelf.
For Example 1,3,5 if the cards 1,3 and 5 are present.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.321.1.3012.1003.1.6 |
ncmCardInfoTable SEQUENCE OF NcmCardInfoEntry .1.3.6.1.4.1.321.1.3012.1004 |
ncmCardInfoEntryAn entry in the ncmCard Info table. NcmCardInfoEntry .1.3.6.1.4.1.321.1.3012.1004.1 |
ncmCardNIDIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1004.1.1 |
ncmCardIndexThis object is the identifier of an Interface
on a managed device. If there is an ifEntry
that is directly associated with this and
only this DS1 interface, it should have the
same value as ifIndex. Otherwise, the value
exceeds ifNumber, and is a unique identifier
following this rule: inside interfaces (e.g.,
equipment side) with even numbers and outside
interfaces (e.g., network side) with odd
numbers.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1004.1.2 |
ncmFirmwareTypeThis variable indicates the firmware type for cards.ro Enumeration .1.3.6.1.4.1.321.1.3012.1004.1.3 |
ncmCimTypeThis variable indicates the cim type for the cards.ro Enumeration .1.3.6.1.4.1.321.1.3012.1004.1.4 |
ncmClearCardInfoThis variable indicates the option to clear the ncmCard
Configuration in EEProm.rw Enumeration .1.3.6.1.4.1.321.1.3012.1004.1.5 |
ncmShelfSyncSourceTable SEQUENCE OF NcmShelfSyncSourceEntry .1.3.6.1.4.1.321.1.3012.1005 |
ncmShelfSyncSourceEntryAn entry in the ncm Shelf Sync Source Time table. NcmShelfSyncSourceEntry .1.3.6.1.4.1.321.1.3012.1005.1 |
ncmShelfSyncNIDIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1005.1.1 |
ncmShelfSyncSourceIndexThis object is the identifier of an Interface
on a managed device. If there is an ifEntry
that is directly associated with this and
only this DS1 interface, it should have the
same value as ifIndex. Otherwise, the value
exceeds ifNumber, and is a unique identifier
following this rule: inside interfaces (e.g.,
equipment side) with even numbers and outside
interfaces (e.g., network side) with odd
numbers.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1005.1.2 |
ncmSourceOneShelfNumThis variable indicates the source one shelf number.rw INTEGER .1.3.6.1.4.1.321.1.3012.1005.1.3 |
ncmSourceOneCardNumThis variable indicates the source one card number.rw INTEGER .1.3.6.1.4.1.321.1.3012.1005.1.4 |
ncmSourceOneClockRefThis variable indicates the source one clock reference.rw Enumeration .1.3.6.1.4.1.321.1.3012.1005.1.5 |
ncmAutoRestore1This variable indicates the source one auto restore.rw Enumeration .1.3.6.1.4.1.321.1.3012.1005.1.6 |
ncmSourceTwoShelfNumThis variable indicates the source two shelf number.rw INTEGER .1.3.6.1.4.1.321.1.3012.1005.1.7 |
ncmSourceTwoCardNumThis variable indicates the source two card number.rw INTEGER .1.3.6.1.4.1.321.1.3012.1005.1.8 |
ncmSourceTwoClockRefThis variable indicates the source two clock reference.rw Enumeration .1.3.6.1.4.1.321.1.3012.1005.1.9 |
ncmAutoRestore2This variable indicates the source two auto restore.rw Enumeration .1.3.6.1.4.1.321.1.3012.1005.1.10 |
ncmSourceThreeShelfNumThis variable indicates the source three shelf number.rw INTEGER .1.3.6.1.4.1.321.1.3012.1005.1.11 |
ncmSourceThreeCardNumThis variable indicates the source three card number.rw INTEGER .1.3.6.1.4.1.321.1.3012.1005.1.12 |
ncmSourceThreeClockRefThis variable indicates the source three clock reference.rw Enumeration .1.3.6.1.4.1.321.1.3012.1005.1.13 |
ncmAutoRestore3This variable indicates the source three auto restore.rw Enumeration .1.3.6.1.4.1.321.1.3012.1005.1.14 |
ncmShelfCurrentSyncSourceThis variable indicates the current sync source.rw Enumeration .1.3.6.1.4.1.321.1.3012.1005.1.15 |
ncmCardSyncSourceTable SEQUENCE OF NcmCardSyncSourceEntry .1.3.6.1.4.1.321.1.3012.1006 |
ncmCardSyncSourceEntryAn entry in the ncmCard Sync ncmSource Time table. NcmCardSyncSourceEntry .1.3.6.1.4.1.321.1.3012.1006.1 |
ncmCardSyncNIDIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1006.1.1 |
ncmCardSyncSourceIndexThis object is the identifier of an Interface
on a managed device. If there is an ifEntry
that is directly associated with this and
only this DS1 interface, it should have the
same value as ifIndex. Otherwise, the value
exceeds ifNumber, and is a unique identifier
following this rule: inside interfaces (e.g.,
equipment side) with even numbers and outside
interfaces (e.g., network side) with odd
numbers.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1006.1.2 |
ncmCardReceiveClockFromShelfThis variable indicates receive sync clock from the shelf for
the card .rw Enumeration .1.3.6.1.4.1.321.1.3012.1006.1.3 |
ncmCardSourceOneShelfNumThis variable indicates the source one shelf number.rw INTEGER .1.3.6.1.4.1.321.1.3012.1006.1.4 |
ncmCardSourceOneCardNumThis variable indicates the source one card number.rw INTEGER .1.3.6.1.4.1.321.1.3012.1006.1.5 |
ncmCardSourceOneClockRefThis variable indicates the source one clock reference.rw Enumeration .1.3.6.1.4.1.321.1.3012.1006.1.6 |
ncmCardAutoRestore1This variable indicates the source one auto restore.rw Enumeration .1.3.6.1.4.1.321.1.3012.1006.1.7 |
ncmCardSourceTwoShelfNumThis variable indicates the source two shelf number.rw INTEGER .1.3.6.1.4.1.321.1.3012.1006.1.8 |
ncmCardSourceTwoCardNumThis variable indicates the source two card number.rw INTEGER .1.3.6.1.4.1.321.1.3012.1006.1.9 |
ncmCardSourceTwoClockRefThis variable indicates the source two clock reference.rw Enumeration .1.3.6.1.4.1.321.1.3012.1006.1.10 |
ncmCardAutoRestore2This variable indicates the source two auto restore.rw Enumeration .1.3.6.1.4.1.321.1.3012.1006.1.11 |
ncmCardSourceThreeShelfNumThis variable indicates the source three shelf number.rw INTEGER .1.3.6.1.4.1.321.1.3012.1006.1.12 |
ncmCardSourceThreeCardNumThis variable indicates the source three card number.rw INTEGER .1.3.6.1.4.1.321.1.3012.1006.1.13 |
ncmCardSourceThreeClockRefThis variable indicates the source three clock reference.rw Enumeration .1.3.6.1.4.1.321.1.3012.1006.1.14 |
ncmCardAutoRestore3This variable indicates the source three auto restore.rw Enumeration .1.3.6.1.4.1.321.1.3012.1006.1.15 |
ncmCardCurrentSyncSourceThis variable indicates the current sync ncm source.rw Enumeration .1.3.6.1.4.1.321.1.3012.1006.1.16 |
ncmIDPromTable SEQUENCE OF NcmIDPromEntry .1.3.6.1.4.1.321.1.3012.1007 |
ncmIDPromEntryAn entry in the ncm ID Prom Table. NcmIDPromEntry .1.3.6.1.4.1.321.1.3012.1007.1 |
ncmIDPromNIDIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1007.1.1 |
ncmIDPromIndexThis object is the identifier of an Interface
on a managed device. If there is an ifEntry
that is directly associated with this and
only this DS1 interface, it should have the
same value as ifIndex. Otherwise, the value
exceeds ifNumber, and is a unique identifier
following this rule: inside interfaces (e.g.,
equipment side) with even numbers and outside
interfaces (e.g., network side) with odd
numbers.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1007.1.2 |
ncmCardTypeThis variable indicates the ncmCard type of the card.ro Enumeration .1.3.6.1.4.1.321.1.3012.1007.1.3 |
ncmCardRevisionThis variable indicates the revision number for the card.ro DisplayString .1.3.6.1.4.1.321.1.3012.1007.1.4 |
ncmCardDateThis variable indicates the date (mm-dd-yy)
for the card.ro DisplayString .1.3.6.1.4.1.321.1.3012.1007.1.5 |
ncmCardSerialNumberThis variable indicates the Serial Number for the card.ro DisplayString .1.3.6.1.4.1.321.1.3012.1007.1.6 |
ncmManufacturePartNumberThis variable indicates the Manufacture Part Number for the
card.ro DisplayString .1.3.6.1.4.1.321.1.3012.1007.1.7 |
ncmVendorCageCodeThis variable indicates the Vendor Cage Code for the card.ro DisplayString .1.3.6.1.4.1.321.1.3012.1007.1.8 |
ncmIDCimTypeThis variable indicates the cim Type for the card.ro Enumeration .1.3.6.1.4.1.321.1.3012.1007.1.9 |
ncmCimRevisionThis variable indicates the revision number for the cim of
the card.ro INTEGER SYNTAX DisplayString .1.3.6.1.4.1.321.1.3012.1007.1.10 |
ncmCimDateThis variable indicates the date (mm-dd-yy) of
the cim for the card.ro DisplayString .1.3.6.1.4.1.321.1.3012.1007.1.11 |
ncmCimSerialNumberThis variable indicates the Serial Number for the card.ro DisplayString .1.3.6.1.4.1.321.1.3012.1007.1.12 |
ncmCimManufacturePartNumberThis variable indicates the Manufacture Part Number for the
card.ro DisplayString .1.3.6.1.4.1.321.1.3012.1007.1.13 |
ncmCimVendorCageCodeThis variable indicates the Vendor Cage Code for the card.ro DisplayString .1.3.6.1.4.1.321.1.3012.1007.1.14 |
ncmE1PortConfigTable SEQUENCE OF NcmE1PortConfigEntry .1.3.6.1.4.1.321.1.3012.1008 |
ncmE1PortConfigEntryAn entry in the E1 Port Configuration table. NcmE1PortConfigEntry .1.3.6.1.4.1.321.1.3012.1008.1 |
ncmE1ConfigNIDIndexThis object is the identifier of the node id index.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1008.1.1 |
ncmE1PortLineIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1008.1.2 |
ncmE1PortCRC4This variable indicates whether the CRC4 for the port is
Enabled or Disabled.rw Enumeration .1.3.6.1.4.1.321.1.3012.1008.1.3 |
ncmE1PortCarrierFailureAlarmThis variable indicates whether the Carrier Failure ncmAlarm
is Enabled or Disabled.rw Enumeration .1.3.6.1.4.1.321.1.3012.1008.1.4 |
ncmE1PortFaseAlarmThis variable indicates whether the Fase ncmAlarm is Major or
Minor Category.rw Enumeration .1.3.6.1.4.1.321.1.3012.1008.1.5 |
ncmE1PortInbandISDNEnableDisableThis variable indicates the Inband, ISDN enable and disable options.rw Enumeration .1.3.6.1.4.1.321.1.3012.1008.1.6 |
ncmE1PortRepeaterLoopbackTimeoutEnableThis variable indicates the option to enable the repeater
loopback timeout.rw Enumeration .1.3.6.1.4.1.321.1.3012.1008.1.7 |
ncmE1PortFramingThis variable indicates the framing for E1 Port.rw Enumeration .1.3.6.1.4.1.321.1.3012.1008.1.8 |
ncmE1PortRepeaterLoopbackTimeoutThis variable indicates the repeater loopback timeout in
seconds for the card.rw INTEGER .1.3.6.1.4.1.321.1.3012.1008.1.9 |
ncmE1PortCarrierFailureAlarmDeclareTimeThis variable indicates the carrier failure alarm declare
time in seconds for the card.rw INTEGER .1.3.6.1.4.1.321.1.3012.1008.1.10 |
ncmE1PortServiceStateThis variable indicates service state of the port.rw Enumeration .1.3.6.1.4.1.321.1.3012.1008.1.11 |
ncmE1PortIdlePatternThis variable indicates the idle pattern for the card.rw INTEGER .1.3.6.1.4.1.321.1.3012.1008.1.12 |
ncmE1TimeSlotThis variable indicates the Time slot used for the given port
directly from the hardware cross point switch for example slot
1-10, if slots 1 to 10 is used or 1,3,4 if slots 1,3 and 4 are
used.ro DisplayString SYNTAX DisplayString .1.3.6.1.4.1.321.1.3012.1008.1.13 |
ncmE1TimeSlotSelectThis variable indicates the number which is choosed for the inband/isdn timeslot.rw INTEGER .1.3.6.1.4.1.321.1.3012.1008.1.14 |
ncmE1PortStatusTable SEQUENCE OF NcmE1PortStatusEntry .1.3.6.1.4.1.321.1.3012.1009 |
ncmE1PortStatusEntryAn entry in the E1 Port Status Table. NcmE1PortStatusEntry .1.3.6.1.4.1.321.1.3012.1009.1 |
ncmE1PortStatusNIDIndexThis object identifies the node id index.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1009.1.1 |
ncmE1PortStatusIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1009.1.2 |
ncmE1PortCRC4ErrorThis variable indicates the occurance of CRC4 error.ro Enumeration .1.3.6.1.4.1.321.1.3012.1009.1.3 |
ncmE1PortFramingSlipThis variable indicates the occurance of framing slip error.ro Enumeration .1.3.6.1.4.1.321.1.3012.1009.1.4 |
ncmE1PortRAIThis variable indicates the occurance of RAI.ro Enumeration .1.3.6.1.4.1.321.1.3012.1009.1.5 |
ncmE1PortLOFAThis variable indicates the occurance of LOFA.ro Enumeration .1.3.6.1.4.1.321.1.3012.1009.1.6 |
ncmE1PortAISThis variable indicates the occurance of AIS.ro Enumeration .1.3.6.1.4.1.321.1.3012.1009.1.7 |
ncmE1PortLOSThis variable indicates the occurance of LOS.ro Enumeration .1.3.6.1.4.1.321.1.3012.1009.1.8 |
ncmE1PortBPVThresholdExceededThis variable indicates whether BPV threshold is exceeded
or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1009.1.9 |
ncmE1BlockErrorCounterThis variable indicates the Block Error Counter.ro Gauge .1.3.6.1.4.1.321.1.3012.1009.1.10 |
ncmE1CodeViolationModeThis variable indicates whether HDB3 or FEBE should be counted.ro Enumeration .1.3.6.1.4.1.321.1.3012.1009.1.11 |
ncmE1CurrentHDB3ORFEBEErrorCountsThis variable indicates the Current HDB3/FEBE error counts.ro Gauge .1.3.6.1.4.1.321.1.3012.1009.1.12 |
ncmE1CurrentFrameErrorCountsThis variable indicates the current Frame Error counts.ro Gauge .1.3.6.1.4.1.321.1.3012.1009.1.13 |
ncmE1CurrentCRC4ErrorCountsThis variable indicates the current crc4 Error counts.ro Gauge .1.3.6.1.4.1.321.1.3012.1009.1.14 |
ncmE1ResetPerfCountReset E1 Performance Counters.rw Enumeration .1.3.6.1.4.1.321.1.3012.1009.1.15 |
ncmE1PortSendRAIThis variable indicates whether the E1 Port Send RAI is enable
or disable.ro Enumeration .1.3.6.1.4.1.321.1.3012.1009.1.16 |
ncmE1PortSendAISThis variable indicates whether the E1 Port Send AIS is enable
or disable.ro Enumeration .1.3.6.1.4.1.321.1.3012.1009.1.17 |
ncmE1PortRFAThis variable indicates whether the E1 Port RFA is on
or off.ro Enumeration .1.3.6.1.4.1.321.1.3012.1009.1.18 |
ncmE1PortBERThresholdExceededThis variable indicates whether BER threshold is exceeded
or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1009.1.19 |
ncmE1PortLLBThis variable indicates whether LLB is on or off.ro Enumeration .1.3.6.1.4.1.321.1.3012.1009.1.20 |
ncmE1PortPLBThis variable indicates whether PLB is on or off.ro Enumeration .1.3.6.1.4.1.321.1.3012.1009.1.21 |
ncmE1PortLOCThis variable indicates whether LOC is on or off.ro Enumeration .1.3.6.1.4.1.321.1.3012.1009.1.22 |
ncmE1PortTestPatternThis variable indicates the test patern in progress:
1 = none
2 = 3/24
3 = QRSS
4 = 2n20-1
5 = 1 in 8
6 = 2N15 - 1
7 = All Zeros
8 = 55 Octets
9 = all onesro Enumeration .1.3.6.1.4.1.321.1.3012.1009.1.23 |
ncmE1CurrentTable SEQUENCE OF NcmE1CurrentEntry .1.3.6.1.4.1.321.1.3012.1010 |
ncmE1CurrentEntryAn entry in the ncm E1 Current table. NcmE1CurrentEntry .1.3.6.1.4.1.321.1.3012.1010.1 |
ncmE1CurrentNIDIndexThis object identifies the node id of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1010.1.1 |
ncmE1CurrentIndexThe index value which uniquely identifies the
interface to which this entry is applicable.
The interface identified by a particular
value of this index is the same interf as
identified by the same value as a LineIndex
object instance.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1010.1.2 |
ncmE1CurrentEndTypeThe variable specifies the End Type.ro Enumeration .1.3.6.1.4.1.321.1.3012.1010.1.3 |
ncmE1CRC4StatusThe variable specifies the CRC4 Status.ro Enumeration .1.3.6.1.4.1.321.1.3012.1010.1.4 |
ncmE1TimestampThe variable specifies the timestamp in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1010.1.5 |
ncmE1Timestamp1The variable specifies the timestamp in milliseconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1010.1.6 |
ncmE1CurrentIntervalSecThe variable specifies the current interval in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1010.1.7 |
ncmE1CurrentASsThe number of Availabe Seconds, encountered by
a DS1 interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1010.1.8 |
ncmE1CurrentUASsThe number of Out of Unavailable Seconds encountered
by a DS1 interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1010.1.9 |
ncmE1CurrentESsThe number of Errored Seconds encountered
by a DS1 interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1010.1.10 |
ncmE1CurrentSESsThe number of Severely Errored Seconds encountered
by a DS1 interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1010.1.11 |
ncmE1CurrentFAEThe number of Frame Alignment Error in Seconds
encountered by a DS1 interface in the current 15
minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1010.1.12 |
ncmE1CurrentBBEThe number of Background Block Error encountered
by a DS1 interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1010.1.13 |
ncmE1CurrentSEFSsThe number of Severly Error Framing seconds encountered
by a DS1 interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1010.1.14 |
ncmE1CurrentAISSsThe number of ncmAlarm Indication Signal seconds encountered
by a DS1 interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1010.1.15 |
ncmE1CurrentLOSSsThe number of Loss of Signal seconds encountered
by a DS1 interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1010.1.16 |
ncmE1CurrentLOFSsThe number of Loss of Signal seconds encountered
by a DS1 interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1010.1.17 |
ncmE1CurrentOOFSsThe number of Out Of Frame seconds encountered
by a DS1 interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1010.1.18 |
ncmE1CurrentCVPathThe number of Code Violation Path encountered
by a DS1 interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1010.1.19 |
ncmE1CurrentCVLineThe number of Code Violation Line encountered
by a DS1 interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1010.1.20 |
ncmE1CurrentESsLineThe number of Errored Seconds Line encountered
by a DS1 interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1010.1.21 |
ncmE1CurrentSESsLineThe number of Severely Errored Seconds Line encountered
by a DS1 interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1010.1.22 |
ncmE1CurrentFECPathThe number of Failure Event Count Path encountered
by a DS1 interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1010.1.23 |
ncmE1CurrentFECLineThe number of Failure Event Count Line encountered
by a DS1 interface in the current 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1010.1.24 |
ncmE1IntervalTable SEQUENCE OF NcmE1IntervalEntry .1.3.6.1.4.1.321.1.3012.1011 |
ncmE1IntervalEntryAn entry in the E1 Interval table. NcmE1IntervalEntry .1.3.6.1.4.1.321.1.3012.1011.1 |
ncmE1IntervalNIDIndexThe object specifies the node id index.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1011.1.1 |
ncmE1IntervalIndexThe index value which uniquely identifies the
DS1 interface to which this entry is applicable.
The interface identified by a particular
value of this index is the same interface as
identified by the same value as a LineIndex
object instance.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1011.1.2 |
ncmE1IntervalEndTypeThe variable specifies the End Type.ro Enumeration .1.3.6.1.4.1.321.1.3012.1011.1.3 |
ncmE1IntervalNumberA number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals are valid).ro INTEGER .1.3.6.1.4.1.321.1.3012.1011.1.4 |
ncmE1IntervalASsThe number of Available Seconds encountered by a
DS1 interface in one of the previous 96, individual
15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1011.1.5 |
ncmE1IntervalUASsThe number of Unavailable Seconds encountered
by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1011.1.6 |
ncmE1IntervalESsThe number of Error Seconds encountered
by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1011.1.7 |
ncmE1IntervalSESsThe number of Severe Error Seconds encountered
by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1011.1.8 |
ncmE1IntervalFAEThe number of Frame Alignment Errors encoun-
tered by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1011.1.9 |
ncmE1IntervalBBEThe number of Background Block Errors encoun-
tered by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1011.1.10 |
ncmE1IntervalSEFSsThe number of Severly Error Framing seconds encountered
by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1011.1.11 |
ncmE1IntervalAISSsThe number of ncmAlarm Indication Signal seconds encountered
by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1011.1.12 |
ncmE1IntervalLOSSsThe number of Loss of Signal seconds encountered
by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1011.1.13 |
ncmE1IntervalLOFSsThe number of Loss of Signal seconds encountered
by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1011.1.14 |
ncmE1IntervalOOFSsThe number of Out Of Frame seconds encountered
by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1011.1.15 |
ncmE1IntervalCVPathThe number of Code Violation Path encountered
by a DS1 interface in one of the previous
96, individual 15 minute, intervals.
This object only has significance for QUAD cards.ro Gauge .1.3.6.1.4.1.321.1.3012.1011.1.16 |
ncmE1IntervalCVLineThe number of Code Violation Line encountered
by a DS1 interface in one of the previous
96, individual 15 minute, intervals.
This object only has significance for QUAD cards.ro Gauge .1.3.6.1.4.1.321.1.3012.1011.1.17 |
ncmE1IntervalESsLineThe number of Errored Seconds Line encountered
by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1011.1.18 |
ncmE1IntervalSESsLineThe number of Severely Errored Seconds Line encountered
by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1011.1.19 |
ncmE1IntervalFECPathThe number of Failure Event Count Path encountered
by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1011.1.20 |
ncmE1IntervalFECLineThe number of Failure Event Count Line encountered
by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1011.1.21 |
ncmE1TotalTable SEQUENCE OF NcmE1TotalEntry .1.3.6.1.4.1.321.1.3012.1012 |
ncmE1TotalEntryAn entry in the Total Entry table. NcmE1TotalEntry .1.3.6.1.4.1.321.1.3012.1012.1 |
ncmE1TotalNIDIndexThe object specifies the node id index of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1012.1.1 |
ncmE1TotalIndexThe index value which uniquely identifies the
DS1 interface to which this entry is applica-
ble. The interface identified by a particular
value of this index is the same interf as
identified by the same value as a LineIndex
object instance.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1012.1.2 |
ncmE1TotalEndTypeThe variable specifies the End Type.ro Enumeration .1.3.6.1.4.1.321.1.3012.1012.1.3 |
ncmE1NumberOfValidIntervalThe number of previous intervals for which
valid data was collected. The value will be 96
unless the interface was brought on-line within
the last 24 hours, in which case the value will
be the number of complete 15 minute intervals
the since interface has been online.ro INTEGER .1.3.6.1.4.1.321.1.3012.1012.1.4 |
ncmE1TotalASsThe number of Available Seconds encountered by a
DS1 interface in the previous 24 hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1012.1.5 |
ncmE1TotalUASsThe number of Unavailable Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1012.1.6 |
ncmE1TotalESsThe number of Error Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1012.1.7 |
ncmE1TotalSESsThe number of Severly Errored Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1012.1.8 |
ncmE1TotalFAEThe number of Frame Alignment Signal errors encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1012.1.9 |
ncmE1TotalBBEThe number of Background Block Errors encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1012.1.10 |
ncmE1TotalSEFSsThe number of Severly Error Framing seconds encountered
by a DS1 interface in 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1012.1.11 |
ncmE1TotalAISSsThe number of ncmAlarm Indication Signal seconds encountered
by a DS1 interface in the 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1012.1.12 |
ncmE1TotalLOSSsThe number of Loss of Signal seconds encountered
by a DS1 interface in the 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1012.1.13 |
ncmE1TotalLOFSsThe number of Loss of Signal seconds encountered
by a DS1 interface in the 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1012.1.14 |
ncmE1TotalOOFSsThe number of Out Of Frame seconds encountered
by a DS1 interface in the 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1012.1.15 |
ncmE1TotalCVPathThe number of Code Violation Path encountered
by a DS1 interface in the 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1012.1.16 |
ncmE1TotalCVLineThe number of Code Violation Line encountered
by a DS1 interface in the 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1012.1.17 |
ncmE1TotalESsLineThe number of Errored Seconds Line encountered
by a DS1 interface in the 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1012.1.18 |
ncmE1TotalSESsLineThe number of Severely Errored Seconds Line encountered
by a DS1 interface in the 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1012.1.19 |
ncmE1TotalFECPathThe number of Failure Event Count Path encountered
by a DS1 interface in the 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1012.1.20 |
ncmE1TotalFECLineThe number of Failure Event Count Line encountered
by a DS1 interface in the 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1012.1.21 |
ncmE1PrevTotalTable SEQUENCE OF NcmE1PrevTotalEntry .1.3.6.1.4.1.321.1.3012.1013 |
ncmE1PrevTotalEntryAn entry in the Previous day total table. NcmE1PrevTotalEntry .1.3.6.1.4.1.321.1.3012.1013.1 |
ncmE1PrevTotalNIDIndexThe object specifies the node id index of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1013.1.1 |
ncmE1PrevTotalIndexThe index value which uniquely identifies the
DS1 interface to which this entry is applica-
ble. The interface identified by a particular
value of this index is the same interf as
identified by the same value as a LineIndex
object instance.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1013.1.2 |
ncmE1PrevTotalEndTypeThe variable specifies the End Type .ro Enumeration .1.3.6.1.4.1.321.1.3012.1013.1.3 |
ncmE1PrevTotalASsThe number of Available Seconds encountered by a
DS1 interface in the previous 24 hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1013.1.4 |
ncmE1PrevTotalUASsThe number of Unavailable Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1013.1.5 |
ncmE1PrevTotalESsThe number of Error Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1013.1.6 |
ncmE1PrevTotalSESsThe number of Severly Errored Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1013.1.7 |
ncmE1PrevTotalFAEThe number of Frame Alignment Signal errors encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1013.1.8 |
ncmE1PrevTotalBBEThe number of Background Block Errors encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1013.1.9 |
ncmE1PrevTotalSEFSsThe number of Severly Error Framing seconds encountered
by a DS1 interface in the prev 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1013.1.10 |
ncmE1PrevTotalAISSsThe number of ncmAlarm Indication Signal seconds encountered
by a DS1 interface in the prev 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1013.1.11 |
ncmE1PrevTotalLOSSsThe number of Loss of Signal seconds encountered
by a DS1 interface in the prev 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1013.1.12 |
ncmE1PrevTotalLOFSsThe number of Loss of Signal seconds encountered
by a DS1 interface in the prev 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1013.1.13 |
ncmE1PrevTotalOOFSsThe number of Out Of Frame seconds encountered
by a DS1 interface in the prev 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1013.1.14 |
ncmE1PrevTotalCVPathThe number of Code Violation Path encountered
by a DS1 interface in the prev 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1013.1.15 |
ncmE1PrevTotalCVLineThe number of Code Violation Line encountered
by a DS1 interface in the prev 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1013.1.16 |
ncmE1PrevTotalESsLineThe number of Errored Seconds Line encountered
by a DS1 interface in the prev 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1013.1.17 |
ncmE1PrevTotalSESsLineThe number of Severely Errored Seconds Line encountered
by a DS1 interface in the prev 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1013.1.18 |
ncmE1PrevTotalFECPathThe number of Failure Event Count Path encountered
by a DS1 interface in the prev 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1013.1.19 |
ncmE1PrevTotalFECLineThe number of Failure Event Count Line encountered
by a DS1 interface in the prev 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1013.1.20 |
ncmE1PerformanceSnapShotTable SEQUENCE OF NcmE1PerformanceSnapShotEntry .1.3.6.1.4.1.321.1.3012.1014 |
ncmE1PerformanceSnapShotEntryAn entry in the E1 Performance Snap Shot Entry table. NcmE1PerformanceSnapShotEntry .1.3.6.1.4.1.321.1.3012.1014.1 |
ncmE1SnapShotNIDIndexThe object specifies the node id index of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1014.1.1 |
ncmE1SnapShotIndexThe index value which uniquely identifies the
DS1 interface to which this entry is applica-
ble. The interface identified by a particular
value of this index is the same interface as
identified by the same value as a LineIndex
object instance.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1014.1.2 |
ncmE1SnapShotEndTypeThe variable specifies the End Type .ro Enumeration .1.3.6.1.4.1.321.1.3012.1014.1.3 |
ncmE1SnapShotThe variable specifies the option to intiate snap shot
command.rw Enumeration .1.3.6.1.4.1.321.1.3012.1014.1.4 |
ncmE1TimeStampSecThe variable specifies the Time Stamp in Seconds .ro INTEGER .1.3.6.1.4.1.321.1.3012.1014.1.5 |
ncmE1TimeMilliSecThe variable specifies the Time Stamp in milli Seconds .ro INTEGER .1.3.6.1.4.1.321.1.3012.1014.1.6 |
ncmE1SecInCurrIntervalThe variable specifies the Seconds in the Current Interval.ro INTEGER .1.3.6.1.4.1.321.1.3012.1014.1.7 |
ncmE1ResetPerfRegReset Performance Monitoring registers.rw Enumeration .1.3.6.1.4.1.321.1.3012.1014.1.8 |
ncmE1PortLatchedStatusTable SEQUENCE OF NcmE1PortLatchedStatusEntry .1.3.6.1.4.1.321.1.3012.1015 |
ncmE1PortLatchedStatusEntryAn entry in the ncm E1 Port Latched Status Table. NcmE1PortLatchedStatusEntry .1.3.6.1.4.1.321.1.3012.1015.1 |
ncmE1PortLatchedStatusNIDIndexThe object specifies the node id index of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1015.1.1 |
ncmE1PortLatchedStatusIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1015.1.2 |
ncmE1PortLatchedCRC4ErrorThis variable indicates the occurance Latched status of CRC4
error.ro Enumeration .1.3.6.1.4.1.321.1.3012.1015.1.3 |
ncmE1PortLatchedFramingSlipThis variable indicates the occurance Latched
status of framing slip error.ro Enumeration .1.3.6.1.4.1.321.1.3012.1015.1.4 |
ncmE1PortLatchedRAIThis variable indicates the occurance Latched status of
RAI.ro Enumeration .1.3.6.1.4.1.321.1.3012.1015.1.5 |
ncmE1PortLatchedLOFAThis variable indicates the occurance Latched status of
LOFA.ro Enumeration .1.3.6.1.4.1.321.1.3012.1015.1.6 |
ncmE1PortLatchedAISThis variable indicates the occurance Latched
status of AIS.ro Enumeration .1.3.6.1.4.1.321.1.3012.1015.1.7 |
ncmE1PortLatchedLOSThis variable indicates the occurance Latched Status of
LOS.ro Enumeration .1.3.6.1.4.1.321.1.3012.1015.1.8 |
ncmE1PortLatchedBPVThresholdExceededThis variable indicates whether BPV threshold is exceeded
or not in Latched state.ro Enumeration .1.3.6.1.4.1.321.1.3012.1015.1.9 |
ncmE1ThresholdStatusTable SEQUENCE OF NcmE1ThresholdStatusEntry .1.3.6.1.4.1.321.1.3012.1016 |
ncmE1ThresholdStatusEntryAn entry in the E1 Threshold Status Table. NcmE1ThresholdStatusEntry .1.3.6.1.4.1.321.1.3012.1016.1 |
ncmE1ThresholdStatusNIDIndexThe object specifies the node id index of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1016.1.1 |
ncmE1ThresholdStatusIndexThis object is the identifier of an Interface
on a managed device. If there is an ifEntry
that is directly associated with this and
only this DS1 interface, it should have the
same value as ifIndex. Otherwise, the value
exceeds ifNumber, and is a unique identifier
following this rule: inside interfaces (e.g.,
equipment side) with even numbers and outside
interfaces (e.g., network side) with odd
numbers.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1016.1.2 |
ncmE1CRCThresholdThis variable indicates the CRC Error Threshold value .ro INTEGER .1.3.6.1.4.1.321.1.3012.1016.1.3 |
ncmE1CRCExceededThis variable indicates whether the CRC Error has exceeded
the Threshold value or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1016.1.4 |
ncmE1SESThresholdThis variable indicates the SES Error Threshold value .ro INTEGER .1.3.6.1.4.1.321.1.3012.1016.1.5 |
ncmE1SESExceededThis variable indicates whether the SES Error has exceeded
the Threshold value or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1016.1.6 |
ncmE1UASThresholdThis variable indicates the UAS Error Threshold value .ro INTEGER .1.3.6.1.4.1.321.1.3012.1016.1.7 |
ncmE1UASExceededThis variable indicates whether the UAS Error has exceeded
the Threshold value or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1016.1.8 |
ncmE1BPVThresholdstThis variable indicates the BPV Error Threshold value .ro INTEGER .1.3.6.1.4.1.321.1.3012.1016.1.9 |
ncmE1BPVExceededThis variable indicates whether the BPV Error has exceeded
the Threshold value or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1016.1.10 |
ncmE1BERThresholdThis variable indicates the BPV Error Threshold value .ro INTEGER .1.3.6.1.4.1.321.1.3012.1016.1.11 |
ncmE1BERExceededThis variable indicates whether the BER Error has exceeded
the Threshold value or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1016.1.12 |
ncmE1RestoreStateThis variable indicates the Restore State of Thresholdro Enumeration .1.3.6.1.4.1.321.1.3012.1016.1.13 |
ncmE1LineRestoreSecThis variable indicates the number of seconds until
the line restores.ro INTEGER .1.3.6.1.4.1.321.1.3012.1016.1.14 |
ncmT1ConfigTable SEQUENCE OF NcmT1ConfigEntry .1.3.6.1.4.1.321.1.3012.1017 |
ncmT1ConfigEntryAn entry in the ncm T1 Configuration table. NcmT1ConfigEntry .1.3.6.1.4.1.321.1.3012.1017.1 |
ncmT1ConfigNIDIndexThis object is the identifier of the node id index.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1017.1.1 |
ncmT1LineIndexThis object is the identifier of an Interface
on a managed device. If there is an ifEntry
that is directly associated with this and
only this DS1 interface, it should have the
same value as ifIndex. Otherwise, the value
exceeds ifNumber, and is a unique identifier
following this rule: inside interfaces (e.g.,
equipment side) with even numbers and outside
interfaces (e.g., network side) with odd
numbers.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1017.1.2 |
ncmT1CRC6This variable indicates Whether CRC6 is enabled or notrw Enumeration .1.3.6.1.4.1.321.1.3012.1017.1.3 |
ncmT1FramingFormatThis variable indicates the variety of
Line implementing this circuit. The type of
circuit affects the number of bits per second
that the circuit can reasonably carry, as well
as the interpretation of the usage and error
statistics. The values, in sequence, describe:
TITLE: SPECIFICATION:
ESF Extended SuperFrame DS1
SF Super Framerw Enumeration .1.3.6.1.4.1.321.1.3012.1017.1.4 |
ncmT1LineCodingThis variable describes the variety of Zero
Code Suppression used on the link, which in
turn affects a number of its characteristics.
B8ZS refers to the use of a specified pat-
tern of normal bits and bipolar violations
which are used to replace a sequence of eight
zero bits.
AMI refers to a mode wherein no zero code
suppression is present and the line encoding
does not solve the problem directly. In this
application, the higher layer must provide data
which meets or exceeds the pulse density re-
quirements, such as inverting HDLC data.rw Enumeration .1.3.6.1.4.1.321.1.3012.1017.1.5 |
ncmT1FramingTypeThis variable indicates the framing type in this
T1 port, i.e., CAS-BR, CAS-CC, CCSrw Enumeration .1.3.6.1.4.1.321.1.3012.1017.1.6 |
ncmT1FDLThe variable specifies the Disable/Enable of the fdl State.rw Enumeration .1.3.6.1.4.1.321.1.3012.1017.1.7 |
ncmT1InbandISDNEnableDisableThis variable indicates the Inband, ISDN enable and disable options.rw Enumeration .1.3.6.1.4.1.321.1.3012.1017.1.8 |
ncmT1EnableNetLoopbackThe variable specifies the Disable/Enable of the Network
intiated Loopback.rw Enumeration .1.3.6.1.4.1.321.1.3012.1017.1.9 |
ncmT1EnableNetOnesDensityThe variable specifies the Disable/Enable of the Network
One's Density.rw Enumeration .1.3.6.1.4.1.321.1.3012.1017.1.10 |
ncmT1DensityPatternThis variable indicates what type of density network is
being sent on the port or line by the device. It only has
significance only when object ncmT1EnableNetOnesDensity is
enabled. The values mean :
'D80Zeros' refers to send a request for network one's density
of 80 zeroes density pattern.
'D15Zeros' refers to send a request for network one's density
of 15 zeroes density pattern.
'D12d5c80Zero'refers to send a request for 12.5% and 80 zeroes
network one's density pattern.
'TR-62411' refers to sending a request for TR6241
network density pattern.rw Enumeration .1.3.6.1.4.1.321.1.3012.1017.1.11 |
ncmT1EnableRepeaterLpbkTimeoutThe variable specifies whether repeater loopback is
enabled or not.rw Enumeration .1.3.6.1.4.1.321.1.3012.1017.1.12 |
ncmT1RepeaterLoopbackTimeoutThe variable specifies the timeout value in seconds for
repeater loopback.rw INTEGER .1.3.6.1.4.1.321.1.3012.1017.1.13 |
ncmT1UserAlarmDeclareTimeThe variable specifies the User ncmAlarm declaration Time in
seconds.rw INTEGER .1.3.6.1.4.1.321.1.3012.1017.1.14 |
ncmT1StateThe variable specifies whether port state is in service or
not.rw Enumeration .1.3.6.1.4.1.321.1.3012.1017.1.15 |
ncmT1NetworkLBOEQLIZThis variable indicates either
(1) for long haul
using, i.e., is 0 , -7.5db, -15db or -22.5db.[pvt];
or (2) for short haul
or port using, i.e., is 0~133, 133~266, 266~399, 399~533
533~655 ft., which is only applicable in port 3 & 4 of
dual csu card.rw Enumeration .1.3.6.1.4.1.321.1.3012.1017.1.16 |
ncmT1TimeSlotThis variable represents the timeslots used for the given
port directly from the hardware crosspoint switch for
example 1-10 if slot 1 to 10 are selected and 1,3,5 if 1,3
and 5 are selected.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.321.1.3012.1017.1.17 |
ncmT1TimeSlotSelectThis variable indicates the number which is choosed for the inband/isdn timeslot.rw INTEGER .1.3.6.1.4.1.321.1.3012.1017.1.18 |
ncmT1PortStatusTable SEQUENCE OF NcmT1PortStatusEntry .1.3.6.1.4.1.321.1.3012.1018 |
ncmT1PortStatusEntryAn entry in the ncm T1 Port Status Table. NcmT1PortStatusEntry .1.3.6.1.4.1.321.1.3012.1018.1 |
ncmT1PortStatusNIDIndexThis object identifies the node id index.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1018.1.1 |
ncmT1PortStatusIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1018.1.2 |
ncmT1PortCRC6ErrorThis variable indicates the occurance of CRC6 error.ro Enumeration .1.3.6.1.4.1.321.1.3012.1018.1.3 |
ncmT1PortFramingSlipThis variable indicates the occurance of framing slip error.ro Enumeration .1.3.6.1.4.1.321.1.3012.1018.1.4 |
ncmT1PortRAIThis variable indicates the occurance of RAI.ro Enumeration .1.3.6.1.4.1.321.1.3012.1018.1.5 |
ncmT1PortLOFThis variable indicates the occurance of LOF.ro Enumeration .1.3.6.1.4.1.321.1.3012.1018.1.6 |
ncmT1PortAISThis variable indicates the occurance of AIS.ro Enumeration .1.3.6.1.4.1.321.1.3012.1018.1.7 |
ncmT1PortLOSThis variable indicates the occurance of LOS.ro Enumeration .1.3.6.1.4.1.321.1.3012.1018.1.8 |
ncmT1PortBPVThresholdExceededThis variable indicates whether BPV threshold is exceeded or
not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1018.1.9 |
ncmT1BlockErrorCounterThis variable indicates the Block Error Counter .ro Gauge .1.3.6.1.4.1.321.1.3012.1018.1.10 |
ncmT1BERExceededThis variable indicates BER excceded or notro Enumeration .1.3.6.1.4.1.321.1.3012.1018.1.11 |
ncmT1PortSendRAIThis variable indicates whether send RAI is on or offro Enumeration .1.3.6.1.4.1.321.1.3012.1018.1.12 |
ncmT1PortSendAISThis variable indicates whether send AIS is on or offro Enumeration .1.3.6.1.4.1.321.1.3012.1018.1.13 |
ncmT1PortCGAThis variable indicates whether CGA is on or offro Enumeration .1.3.6.1.4.1.321.1.3012.1018.1.14 |
ncmT1PortLLBThis variable indicates whether LLB is on or offro Enumeration .1.3.6.1.4.1.321.1.3012.1018.1.15 |
ncmT1PortPLBThis variable indicates whether PLB is on or offro Enumeration .1.3.6.1.4.1.321.1.3012.1018.1.16 |
ncmT1PortLOCThis variable indicates whether LOC is on or offro Enumeration .1.3.6.1.4.1.321.1.3012.1018.1.17 |
ncmT1PortTestPatternThis variable indicates the test patern in progress:
1 = none
2 = 3/24
3 = QRSS
4 = 2n20-1
5 = 1 in 8
6 = 2N15 - 1
7 = All Zeros
8 = 55 Octets
9 = all onesro Enumeration .1.3.6.1.4.1.321.1.3012.1018.1.18 |
ncmT1CurrentTable SEQUENCE OF NcmT1CurrentEntry .1.3.6.1.4.1.321.1.3012.1019 |
ncmT1CurrentEntryAn entry in the ncm T1 Current table. NcmT1CurrentEntry .1.3.6.1.4.1.321.1.3012.1019.1 |
ncmT1CurrentNIDIndexThis object identifies the node id of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1019.1.1 |
ncmT1CurrentIndexThe index value which uniquely identifies the
interf to which this entry is applicable.
The interface identified by a particular
value of this index is the same interface as
identified by the same value as a LineIndex
object instance.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1019.1.2 |
ncmT1CurrentEndTypeThe variable specifies the End Type .ro Enumeration .1.3.6.1.4.1.321.1.3012.1019.1.3 |
ncmT1TimestampThe variable specifies the Timestamp in seconds .ro INTEGER .1.3.6.1.4.1.321.1.3012.1019.1.4 |
ncmT1Timestamp1The variable specifies the Timestamp in millieseconds .ro INTEGER .1.3.6.1.4.1.321.1.3012.1019.1.5 |
ncmT1CurrentIntervalSecThe variable specifies the Current Interval seconds .ro INTEGER .1.3.6.1.4.1.321.1.3012.1019.1.6 |
ncmT1CurrentASsThe number of Availabe Seconds, encountered by
a DS1 interface in the current 15 minute inter-
val.ro Gauge .1.3.6.1.4.1.321.1.3012.1019.1.7 |
ncmT1CurrentUASsThe number of Out of Unavailable Seconds encountered
by a DS1 interface in the current 15 minute in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1019.1.8 |
ncmT1CurrentESsThe number of Errored Seconds encountered
by a DS1 interface in the current 15 minute in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1019.1.9 |
ncmT1CurrentBESsThe number of Bursty Errored Seconds encountered
by a DS1 interface in the current 15 minute in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1019.1.10 |
ncmT1CurrentSESsThe number of Severely Errored Seconds encountered
by a DS1 interface in the current 15 minute in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1019.1.11 |
ncmT1CurrentSEFsThe number of Severely Errored Framing Seconds encountered
by a DS1 interface in the current 15 minute in-terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1019.1.12 |
ncmT1CurrentLOSsThe number of Loss of Signal Seconds encountered
by a DS1 interface in the current 15 minute in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1019.1.13 |
ncmT1CurrentAISsThe number of ncmAlarm Indication Signal Seconds encountered
by a DS1 interface in the current 15 minute in-terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1019.1.14 |
ncmT1CurrentLOFsThe number of Loss Of Frame Seconds encountered
by a DS1 interface in the current 15 minute in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1019.1.15 |
ncmT1CurrentOOFsThe number of Out Of Frame Seconds encountered
by a DS1 interface in the current 15 minute in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1019.1.16 |
ncmT1CurrentESsTypeAThe number of Errored seconds of type A encountered
by a DS1 interface in the current 15 minute in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1019.1.17 |
ncmT1CurrentSASsThe number of SEF/AIS encountered
by a DS1 interface in the current 15 minute in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1019.1.18 |
ncmT1CurrentCSSsThe number of controlled slip seconds encountered
by a DS1 interface in the current 15 minute in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1019.1.19 |
ncmT1CurrentLOFCThe number of Loss of frame counts encountered
by a DS1 interface in the current 15 minute in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1019.1.20 |
ncmT1CurrentFrameErrCountThe number of Framing Error Count encountered
by a DS1 interface in the current 15 minute in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1019.1.21 |
ncmT1CurrentErrorFreeSecThe number of Error Free Seconds encountered
by a DS1 interface in the current 15 minute in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1019.1.22 |
ncmT1CurrentDegradedMinThe number of Degraded Minutes encountered
by a DS1 interface in the current 15 minute in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1019.1.23 |
ncmT1IntervalTable SEQUENCE OF NcmT1IntervalEntry .1.3.6.1.4.1.321.1.3012.1020 |
ncmT1IntervalEntryAn entry in the ncm T1 Interval table. NcmT1IntervalEntry .1.3.6.1.4.1.321.1.3012.1020.1 |
ncmT1IntervalNIDIndexThe object specifies the node id index.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1020.1.1 |
ncmT1IntervalIndexThe index value which uniquely identifies the
DS1 interface to which this entry is applica-
ble. The interface identified by a particular
value of this index is the same interface as
identified by the same value as a LineIndex
object instance.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1020.1.2 |
ncmT1IntervalEndTypeThe variable specifies the End Type .ro Enumeration .1.3.6.1.4.1.321.1.3012.1020.1.3 |
ncmT1IntervalNumberA number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes inter-
val (assuming that all 96 intervals are
valid).ro INTEGER .1.3.6.1.4.1.321.1.3012.1020.1.4 |
ncmT1IntervalASsThe number of Available Seconds encountered by a
DS1 interface in one of the previous 96, indi-
vidual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1020.1.5 |
ncmT1IntervalUASsThe number of Unavailable Seconds encoun-
tered by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1020.1.6 |
ncmT1IntervalESsThe number of Error Seconds encoun-
tered by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1020.1.7 |
ncmT1IntervalBESsThe number of Bursty Error Seconds encoun-
tered by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1020.1.8 |
ncmT1IntervalSESsThe number of Severe Error Seconds encoun-
tered by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1020.1.9 |
ncmT1IntervalSEFsThe number of Severely Errored Framing Seconds
encountered by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1020.1.10 |
ncmT1IntervalLOSsThe number of Loss of Signal Seconds encoun-
tered by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1020.1.11 |
ncmT1IntervalAISsThe number of ncmAlarm Indication Signal Seconds encoun-
tered by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1020.1.12 |
ncmT1IntervalLOFsThe number of Loss Of Frame Seconds encoun-
tered by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1020.1.13 |
ncmT1IntervalOOFsThe number of Out Of Frame Seconds encoun-
tered by a DS1 interface in one of the previous
96, individual 15 minute, intervals.ro Gauge .1.3.6.1.4.1.321.1.3012.1020.1.14 |
ncmT1IntervalESsTypeAThe number of Errored seconds of type A encountered
by a DS1 interface in one of the previous 96,
individual 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1020.1.15 |
ncmT1IntervalSASsThe number of SEF/AIS encountered
by a DS1 interface in one of the previous 96,
individual 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1020.1.16 |
ncmT1IntervalCSSsThe number of controlled slip seconds encountered
by a DS1 interface in one of the previous 96,
individual 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1020.1.17 |
ncmT1IntervalLOFCThe number of Loss of frame counts encountered
by a DS1 interface in one of the previous 96,
individual 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1020.1.18 |
ncmT1IntervalFrameErrThe number of Framing Error Count encountered
by a DS1 interface in one of the previous 96,
individual 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1020.1.19 |
ncmT1IntervalErrFreeSecThe number of Error Free Seconds encountered
by a DS1 interface in one of the previous 96,
individual 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1020.1.20 |
ncmT1IntervalDegradMinThe number of Degraded Minutes encountered
by a DS1 interface in one of the previous 96,
individual 15 minute interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1020.1.21 |
ncmT1TotalTable SEQUENCE OF NcmT1TotalEntry .1.3.6.1.4.1.321.1.3012.1021 |
ncmT1TotalEntryAn entry in the DS1 Total Loss table. NcmT1TotalEntry .1.3.6.1.4.1.321.1.3012.1021.1 |
ncmT1TotalNIDIndexThe object specifies the node id index of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1021.1.1 |
ncmT1TotalIndexThe index value which uniquely identifies the
DS1 interface to which this entry is applica-
ble. The interface identified by a particular
value of this index is the same interface as
identified by the same value as a LineIndex
object instance.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1021.1.2 |
ncmT1TotalEndTypeThe variable specifies the End Type .ro Enumeration .1.3.6.1.4.1.321.1.3012.1021.1.3 |
ncmT1NumberOfValidIntervalsThe number of previous intervals for which
valid data was collected. The value will be 96
unless the interface was brought on-line within
the last 24 hours, in which case the value will
be the number of complete 15 minute intervals
the since interface has been online.ro INTEGER .1.3.6.1.4.1.321.1.3012.1021.1.4 |
ncmT1TotalASsThe number of Available Seconds encountered by a
DS1 interface in the previous 24 hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1021.1.5 |
ncmT1TotalUASsThe number of Unavailable Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1021.1.6 |
ncmT1TotalESsThe number of Unavailable Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1021.1.7 |
ncmT1TotalBESsThe number of Unavailable Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1021.1.8 |
ncmT1TotalSESsThe number of Severly errored Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1021.1.9 |
ncmT1TotalSEFsThe number of Severly Errored frame Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1021.1.10 |
ncmT1TotalLOSsThe number of Loss Of Signal Errors encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1021.1.11 |
ncmT1TotalAISsThe number of ncmAlarm Indication Signal Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1021.1.12 |
ncmT1TotalLOFsThe number of Loss Of Frame Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1021.1.13 |
ncmT1TotalOOFsThe number of Out Of Frame Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1021.1.14 |
ncmT1TotalESsTypeAThe number of Errored seconds of type A encountered
by a DS1 interface in the previous 24 hour in
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1021.1.15 |
ncmT1TotalSASsThe number of SEF/AIS encountered
by a DS1 interface in the previous 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1021.1.16 |
ncmT1TotalCSSsThe number of controlled slip seconds encountered
by a DS1 interface in the previous 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1021.1.17 |
ncmT1TotalLOFCThe number of Loss of frame counts encountered
by a DS1 interface in the previous 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1021.1.18 |
ncmT1TotalFrameErrCountThe number of Framing Error Count encountered
by a DS1 interface in the previous 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1021.1.19 |
ncmT1TotalErrorFreeSecThe number of Error free seconds encountered
by a DS1 interface in the previous 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1021.1.20 |
ncmT1TotalDegradedMinThe number of Degraded Minutes encountered
by a DS1 interface in the previous 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1021.1.21 |
ncmT1PrevTotalTable SEQUENCE OF NcmT1PrevTotalEntry .1.3.6.1.4.1.321.1.3012.1022 |
ncmT1PrevTotalEntryAn entry in the DS1 Total Loss table. NcmT1PrevTotalEntry .1.3.6.1.4.1.321.1.3012.1022.1 |
ncmT1PrevTotalNIDIndexThe object specifies the node id index of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1022.1.1 |
ncmT1PrevTotalIndexThe index value which uniquely identifies the
DS1 interface to which this entry is applica-
ble. The interface identified by a particular
value of this index is the same interface as
identified by the same value as a LineIndex
object instance.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1022.1.2 |
ncmT1PrevTotalEndTypeThe variable specifies the End Type .ro Enumeration .1.3.6.1.4.1.321.1.3012.1022.1.3 |
ncmT1PrevTotalASsThe number of Available Seconds encountered by a
DS1 interface in the previous 24 hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1022.1.4 |
ncmT1PrevTotalUASsThe number of Unavailable Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1022.1.5 |
ncmT1PrevTotalESsThe number of Unavailable Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1022.1.6 |
ncmT1PrevTotalBESsThe number of Unavailable Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1022.1.7 |
ncmT1PrevTotalSESsThe number of Severly Errored Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1022.1.8 |
ncmT1PrevTotalSEFsThe number of Severly Errored frame Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1022.1.9 |
ncmT1PrevTotalLOSsThe number of Loss Of Signal Errors encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1022.1.10 |
ncmT1PrevTotalAISsThe number of ncmAlarm Indication Signal Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1022.1.11 |
ncmT1PrevTotalLOFsThe number of Loss Of Frame Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1022.1.12 |
ncmT1PrevTotalOOFsThe number of Out Of Frame Seconds encoun-
tered by a DS1 interface in the previous 24
hour interval.ro Gauge .1.3.6.1.4.1.321.1.3012.1022.1.13 |
ncmT1PrevTotalESsTypeAThe number of Errored seconds of type A encountered
by a DS1 interface in the previous 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1022.1.14 |
ncmT1PrevTotalSASsThe number of SEF/AIS encountered
by a DS1 interface in the previous 24 hour in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1022.1.15 |
ncmT1PrevTotalCSSsThe number of controlled slip seconds encountered
by a DS1 interface in the previous in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1022.1.16 |
ncmT1PrevTotalLOFCThe number of Loss of frame counts encountered
by a DS1 interface in the previous in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1022.1.17 |
ncmT1PrevTotalFrameErrCountThe number of Framing Error Count encountered
by a DS1 interface in the previous in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1022.1.18 |
ncmT1PrevTotalErrorFreeSecThe number of Error free seconds encountered
by a DS1 interface in the previous in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1022.1.19 |
ncmT1PrevTotalDegradedMinThe number of Degraded Minutes encountered
by a DS1 interface in the previous in-
terval.ro Gauge .1.3.6.1.4.1.321.1.3012.1022.1.20 |
ncmT1PreformanceSnapShotTable SEQUENCE OF NcmT1PreformanceSnapShotEntry .1.3.6.1.4.1.321.1.3012.1023 |
ncmT1PreformanceSnapShotEntryAn entry in the T1 Performance Snap Shot Entry
table. NcmT1PreformanceSnapShotEntry .1.3.6.1.4.1.321.1.3012.1023.1 |
ncmT1SnapShotNIDIndexThe object specifies the node id index of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1023.1.1 |
ncmT1SnapShotIndexThe index value which uniquely identifies the
DS1 interface to which this entry is applica-
ble. The interface identified by a particular
value of this index is the same interface as
identified by the same value as a LineIndex
object instance.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1023.1.2 |
ncmT1SnapShotEndTypeThe variable specifies the End Type .ro Enumeration .1.3.6.1.4.1.321.1.3012.1023.1.3 |
ncmT1SnapShotThe variable specifies the option to intiate snap shot
command.rw Enumeration .1.3.6.1.4.1.321.1.3012.1023.1.4 |
ncmT1TimeStampSecThe variable specifies the Time Stamp in Seconds .ro INTEGER .1.3.6.1.4.1.321.1.3012.1023.1.5 |
ncmT1TimeStampMilliSecThe variable specifies the Time Stamp in milli Seconds .ro INTEGER .1.3.6.1.4.1.321.1.3012.1023.1.6 |
ncmT1CurrIntervalSecThe variable specifies the current interval in Seconds .ro INTEGER .1.3.6.1.4.1.321.1.3012.1023.1.7 |
ncmT1ResetPerfRegReset Performance Monitoring registers.rw Enumeration .1.3.6.1.4.1.321.1.3012.1023.1.8 |
ncmAdvancedT1ConfigTable SEQUENCE OF NcmAdvancedT1ConfigEntry .1.3.6.1.4.1.321.1.3012.1024 |
ncmAdvancedT1ConfigEntryAn entry in the Advanced T1 Configuration table . NcmAdvancedT1ConfigEntry .1.3.6.1.4.1.321.1.3012.1024.1 |
ncmAdvancedT1NIDIndexThe object specifies the node id of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1024.1.1 |
ncmAdvancedT1LineIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1024.1.2 |
ncmadvfdlModeThe variable specifies the fdl mode which is bit 0 of fdl
Parameter1.rw Enumeration .1.3.6.1.4.1.321.1.3012.1024.1.3 |
ncmadvfdlStandardThe variable specifies the fdl standard which is bits 1
and bit 2 of fdl Parameter1.rw Enumeration .1.3.6.1.4.1.321.1.3012.1024.1.4 |
ncmadvfdlPerformanceReportThe variable specifies the fdl standard which is bits 3
and bit 4 of fdl Parameter1.rw Enumeration .1.3.6.1.4.1.321.1.3012.1024.1.5 |
ncmadvfdlLBEnableThe variable specifies the Disable/Enable of the fdl Loopback
which is bit 0 of the fdl-looprw Enumeration .1.3.6.1.4.1.321.1.3012.1024.1.6 |
ncmadvfdlLLBT1BOPMsgThe variable specifies the Disable/Enable of the send/receive
of the LLB T1.403 BOP Messages. It is the bit 1 of the
fdl-loop.rw Enumeration .1.3.6.1.4.1.321.1.3012.1024.1.7 |
ncmadvfdlPLBT1BOPMsgThe variable specifies the Disable/Enable of the send/receive
of the PLB T1.403 BOP Messages. It is the bit 2 of the
fdl-looprw Enumeration .1.3.6.1.4.1.321.1.3012.1024.1.8 |
ncmadvfdlIdlePatternThe variable specifies the fdl idle pattern which is bit 0 of
fdl Parameter2.rw Enumeration .1.3.6.1.4.1.321.1.3012.1024.1.9 |
ncmadvfdlMonitoringCsuTypeThe variable specifies the fdl standard which is bits 1
and bit 2 of fdl Parameter2.rw Enumeration .1.3.6.1.4.1.321.1.3012.1024.1.10 |
ncmT1LatchedStatusTable SEQUENCE OF NcmT1LatchedStatusEntry .1.3.6.1.4.1.321.1.3012.1025 |
ncmT1LatchedStatusEntryAn entry in the DS1 Port Latched Status Table. NcmT1LatchedStatusEntry .1.3.6.1.4.1.321.1.3012.1025.1 |
ncmT1LatchedStatusNIDIndexThe object specifies the node id of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1025.1.1 |
ncmT1LatchedStatusIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1025.1.2 |
ncmT1LatchedStatusEndTypeThe variable specifies the End Type .ro Enumeration .1.3.6.1.4.1.321.1.3012.1025.1.3 |
ncmT1LatchedStatusCRC6ErrorThis variable indicates the occurance of CRC6 error
of the port latched status.ro Enumeration .1.3.6.1.4.1.321.1.3012.1025.1.4 |
ncmT1LatchedStatusFramingSlipThis variable indicates the occurance of framing slip error
of the port latched status.ro Enumeration .1.3.6.1.4.1.321.1.3012.1025.1.5 |
ncmT1LatchedStatusRAIThis variable indicates the occurance Latched status of
RAI for T1 port.ro Enumeration .1.3.6.1.4.1.321.1.3012.1025.1.6 |
ncmT1LatchedStatusLOFThis variable indicates the occurance Latched status of
LOF of T1 port.ro Enumeration .1.3.6.1.4.1.321.1.3012.1025.1.7 |
ncmT1LatchedStatusAISThis variable indicates the occurance T1 port Latched
status of AIS.ro Enumeration .1.3.6.1.4.1.321.1.3012.1025.1.8 |
ncmT1LatchedStatusLOSThis variable indicates the occurance Latched Status of
LOS for T1 port.ro Enumeration .1.3.6.1.4.1.321.1.3012.1025.1.9 |
ncmT1LatchedStatusBPVThreExcdThis variable indicates the BPV Threshold Exceeded
of T1 port Latched Status.ro Gauge .1.3.6.1.4.1.321.1.3012.1025.1.10 |
ncmT1LatchedStatusBERExceededThis variable indicates the BER Exceeded
of T1 port Latched Status.ro Gauge .1.3.6.1.4.1.321.1.3012.1025.1.11 |
ncmT1ThresholdStatusTable SEQUENCE OF NcmT1ThresholdStatusEntry .1.3.6.1.4.1.321.1.3012.1026 |
ncmT1ThresholdStatusEntryAn entry in the DS1 Port Threshold Status Table. NcmT1ThresholdStatusEntry .1.3.6.1.4.1.321.1.3012.1026.1 |
ncmT1ThresholdStatusNIDIndexThe object specifies the node id of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1026.1.1 |
ncmT1ThresholdStatusIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1026.1.2 |
ncmT1ThresholdStatusEndTypeThe variable specifies the End Type .ro Enumeration .1.3.6.1.4.1.321.1.3012.1026.1.3 |
ncmT1ThresholdRestoreStateThis variable indicates the restore state of
T1 port threshold status.ro Enumeration .1.3.6.1.4.1.321.1.3012.1026.1.4 |
ncmT1ThresholdSecLineRestoreThis variable indicates the number of second until line
restores(if restore mode is AUTO) of T1 port threshold Status.ro Gauge .1.3.6.1.4.1.321.1.3012.1026.1.5 |
ncmT1ThresholdBERExceededThis variable indicates BER exceeded or not
of T1 Threshold Status.ro Enumeration .1.3.6.1.4.1.321.1.3012.1026.1.6 |
ncmT1ThresholdBERCountThis variable indicates the BER Count(reserved -
always 0) of T1 port threshold Status.ro Gauge .1.3.6.1.4.1.321.1.3012.1026.1.7 |
ncmT1ThresholdSESExceededThis variable indicates SES exceeded or not
of T1 Threshold Status.ro Enumeration .1.3.6.1.4.1.321.1.3012.1026.1.8 |
ncmT1ThresholdSESCountThis variable indicates the SES Count
of T1 port threshold Status.ro Gauge .1.3.6.1.4.1.321.1.3012.1026.1.9 |
ncmT1ThresholdUASExceededThis variable indicates UAS exceeded or not
of T1 Threshold Status.ro Enumeration .1.3.6.1.4.1.321.1.3012.1026.1.10 |
ncmT1ThresholdUASCountThis variable indicates the UAS Count
of T1 port threshold Status.ro Gauge .1.3.6.1.4.1.321.1.3012.1026.1.11 |
ncmT1ThresholdCRCExceededThis variable indicates CRC exceeded or not
of T1 Threshold Status.ro Enumeration .1.3.6.1.4.1.321.1.3012.1026.1.12 |
ncmT1ThresholdCRCCountThis variable indicates the CRC Count
of T1 port threshold Status.ro Gauge .1.3.6.1.4.1.321.1.3012.1026.1.13 |
ncmT1ThresholdBPVExceededThis variable indicates BPV exceeded or not
of T1 Threshold Status.ro Enumeration .1.3.6.1.4.1.321.1.3012.1026.1.14 |
ncmT1ThresholdBPVCountThis variable indicates the BPV Count
of T1 port threshold Status.ro Gauge .1.3.6.1.4.1.321.1.3012.1026.1.15 |
ncmT1PerformanceCountersTable SEQUENCE OF NcmT1PerformanceCountersEntry .1.3.6.1.4.1.321.1.3012.1027 |
ncmT1PerformanceCountersEntryAn entry in the ncm T1 Performance Counters Entry
table. NcmT1PerformanceCountersEntry .1.3.6.1.4.1.321.1.3012.1027.1 |
ncmT1PerfCountNIDIndexThe object specifies the node id index of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1027.1.1 |
ncmT1PerfCountIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1027.1.2 |
ncmT1PerfCountEndTypeThe variable specifies the End Type of
T1 Performance Counter.ro Enumeration .1.3.6.1.4.1.321.1.3012.1027.1.3 |
ncmT1PerfCountFrameModeThe variable specifies the Framing Mode of
T1 Performance Counter.ro Enumeration .1.3.6.1.4.1.321.1.3012.1027.1.4 |
ncmT1PerfCountCurESFErrEvtThis variable specifies the Current ESF
events of T1 Performance Counter.
This object has no significance for QUAD cards.ro Gauge .1.3.6.1.4.1.321.1.3012.1027.1.5 |
ncmT1PerfCountCurBPVErrCntThis variable specifies the Current BPV
counts of T1 Performance Counter.
This object has no significance for QUAD cards.ro Gauge .1.3.6.1.4.1.321.1.3012.1027.1.6 |
ncmT1PerfCountCurFrameErrCntThis variable specifies the Current Frame
Error counts of T1 Performance Counter.
This object has no significance for QUAD cards.ro Gauge .1.3.6.1.4.1.321.1.3012.1027.1.7 |
ncmT1PerfCountCurCRC6ErrorThis variable specifies the Current CRC-6
errors of T1 Performance Counter.
This object has no significance for QUAD cards.ro Gauge .1.3.6.1.4.1.321.1.3012.1027.1.8 |
ncmT1ResetPerfCountReset ncm T1 Performance Counters.rw Enumeration .1.3.6.1.4.1.321.1.3012.1027.1.9 |
ncmDataPortConfigTable SEQUENCE OF NcmDataPortConfigEntry .1.3.6.1.4.1.321.1.3012.1028 |
ncmDataPortConfigEntryAn entry in the ncmData Port Configuration Entry
table. NcmDataPortConfigEntry .1.3.6.1.4.1.321.1.3012.1028.1 |
ncmDataPortConfigNIDIndexThe object specifies the node id of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1028.1.1 |
ncmDataPortConfigIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1028.1.2 |
ncmDataPortConfigModeThe variable specifies the data port mode whether it is
configured as DTE/DCE.rw Enumeration .1.3.6.1.4.1.321.1.3012.1028.1.3 |
ncmDataPortConfigLineIndicateThe variable specifies the control line indicator for X.21 only,
set to 0 if line is low while set to 1 if line is high.rw Enumeration .1.3.6.1.4.1.321.1.3012.1028.1.4 |
ncmDataPortLineStatusCDCCThe variable specifies the bit 0 status of control line;
where 0=low, 1=high; Status is CD/DTR if Mode = DTE while is CC/DSR if Mode = DCErw Enumeration .1.3.6.1.4.1.321.1.3012.1028.1.5 |
ncmDataPortLineStatusCACBThe variable specifies the bit 1 status of control line;
where 0=low, 1=high; Status is CA/RTS if Mode = DTE while is CB/CTS if Mode = DCErw Enumeration .1.3.6.1.4.1.321.1.3012.1028.1.6 |
ncmDataPortLineStatusLLCJThe variable specifies the bit 2 status of control line;
where 0=low, 1=high; Status is LL if Mode = DTE while is CJ/DCD if Mode = DCErw Enumeration .1.3.6.1.4.1.321.1.3012.1028.1.7 |
ncmDataPortLineStatusRLTMThe variable specifies the bit 2 status of control line;
where 0=low, 1=high; Status is RL if Mode = DTE while is TM if Mode = DCErw Enumeration .1.3.6.1.4.1.321.1.3012.1028.1.8 |
ncmDataPortConfigLOSThe variable specifies the bit 7 status of control line;
where 0=disable, 1=enable; Status is LOS Moderw Enumeration .1.3.6.1.4.1.321.1.3012.1028.1.9 |
ncmDataPortConfigServiceStateThe variable specifies the service state of this data port.rw Enumeration .1.3.6.1.4.1.321.1.3012.1028.1.10 |
ncmDataPortConfigClkOptThe variable specifies the clocking option of this data port.rw Enumeration .1.3.6.1.4.1.321.1.3012.1028.1.11 |
ncmDataPortStatusTable SEQUENCE OF NcmDataPortStatusEntry .1.3.6.1.4.1.321.1.3012.1029 |
ncmDataPortStatusEntryAn entry in the ncmData Port Status Entry
table. NcmDataPortStatusEntry .1.3.6.1.4.1.321.1.3012.1029.1 |
ncmDataPortStatusNIDIndexThe object specifies the node id of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1029.1.1 |
ncmDataPortStatusIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1029.1.2 |
ncmDataPortStatusModeThe variable specifies the data port mode whether it is
configured as DCE/DCE.ro Enumeration .1.3.6.1.4.1.321.1.3012.1029.1.3 |
ncmDataPortStatusLineIndicateThe variable specifies the control line indicator for X.21 only,
set to 0 if line is low while set to 1 if line is high.ro Enumeration .1.3.6.1.4.1.321.1.3012.1029.1.4 |
ncmDataPortStatusLineCDCCThe variable specifies the bit 0 status of control line;
where 0=low, 1=high; Status is CD/DTR if Mode = DTE while is CC/DSR if Mode = DCEro Enumeration .1.3.6.1.4.1.321.1.3012.1029.1.5 |
ncmDataPortStatusLineCACBThe variable specifies the bit 1 status of control line;
where 0=low, 1=high; Status is CA/RTS if Mode = DTE while is CB/CTS if Mode = DCEro Enumeration .1.3.6.1.4.1.321.1.3012.1029.1.6 |
ncmDataPortStatusLineLLCJThe variable specifies the bit 2 status of control line;
where 0=low, 1=high; Status is LL if Mode = DTE while is CJ/DCD if Mode = DCEro Enumeration .1.3.6.1.4.1.321.1.3012.1029.1.7 |
ncmDataPortStatusLineRLTMThe variable specifies the bit 3 status of control line;
where 0=low, 1=high; Status is RL if Mode = DTE while is TM if Mode = DCEro Enumeration .1.3.6.1.4.1.321.1.3012.1029.1.8 |
ncmDataPortStatusLineLOSThe variable specifies the bit 7 status of control line;
where 0=disable, 1=enable; Status is LOS Modero Enumeration .1.3.6.1.4.1.321.1.3012.1029.1.9 |
ncmDataPortStatusServiceStateThe variable specifies the service state of this data port.ro Enumeration .1.3.6.1.4.1.321.1.3012.1029.1.10 |
ncmDataPortStatusCimTypeThe variable specifies the connector interface module type of this data port.ro Enumeration .1.3.6.1.4.1.321.1.3012.1029.1.11 |
ncmDataPortStatusLoopbackThe variable specifies the loopback diagnostic status of this data port.ro Enumeration .1.3.6.1.4.1.321.1.3012.1029.1.12 |
ncmDataPortTestPatternThe variable specifies the test pattern in progress of this data port.ro Enumeration .1.3.6.1.4.1.321.1.3012.1029.1.13 |
ncmDataPortTstPatErrCountThis variable indicates the Test Pattern Error Count.ro Gauge .1.3.6.1.4.1.321.1.3012.1029.1.14 |
ncmALARMConfigTable SEQUENCE OF NcmALARMConfigEntry .1.3.6.1.4.1.321.1.3012.1030 |
ncmALARMConfigEntryAn entry in the ncmAlarm Configure table. NcmALARMConfigEntry .1.3.6.1.4.1.321.1.3012.1030.1 |
ncmAlarmConfigNIDIndexThe object specifies the node id of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1030.1.1 |
ncmAlarmConfigIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1030.1.2 |
ncmAlmCfgDomainThe variable specifies the Domain the alarm came from.rw INTEGER .1.3.6.1.4.1.321.1.3012.1030.1.3 |
ncmAlmCfgSrcAddrThe variable specifies the Address where the alarm
came from.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.321.1.3012.1030.1.4 |
ncmAlmCfgCardThe variable specifies the card in a specified shelf.rw INTEGER .1.3.6.1.4.1.321.1.3012.1030.1.5 |
ncmAlmCfgShelfThe variable specifies the particular shelf.rw INTEGER .1.3.6.1.4.1.321.1.3012.1030.1.6 |
ncmAlmCfgE1T1Port1EnableAlmRptThe variable Enable/Disable the alarm reporting of the
Port #1 for E1/T1 by specifying the bit 0; 1=yes, 0=no.rw Enumeration .1.3.6.1.4.1.321.1.3012.1030.1.7 |
ncmAlmCfgE1T1Port2EnableAlmRptThe variable Enable/Disable the alarm reporting of the
Port #2 for E1/T1 by specifying the bit 1; 1=yes, 0=no.rw Enumeration .1.3.6.1.4.1.321.1.3012.1030.1.8 |
ncmAlmCfgE1T1Port3EnableAlmRptThe variable Enable/Disable the alarm reporting of the
Port #3 for E1/T1 by specifying the bit 0; 1=yes, 0=no.rw Enumeration .1.3.6.1.4.1.321.1.3012.1030.1.9 |
ncmAlmCfgE1T1Port4EnableAlmRptThe variable Enable/Disable the alarm reporting of the
Port #4 for E1/T1 by specifying the bit 1; 1=yes, 0=no.rw Enumeration .1.3.6.1.4.1.321.1.3012.1030.1.10 |
ncmAlmCfgDataPort1EnableAlmRptThe variable Enable/Disable the alarm reporting of the
Port #1 for ncmData by specifying the bit 0; 1=yes, 0=no.
This object has no significance in QUAD cards.rw Enumeration .1.3.6.1.4.1.321.1.3012.1030.1.11 |
ncmAlmCfgDataPort2EnableAlmRptThe variable Enable/Disable the alarm reporting of the
Port #2 for ncmData by specifying the bit 1; 1=yes, 0=no.
This object has no significance in QUAD cards.rw Enumeration .1.3.6.1.4.1.321.1.3012.1030.1.12 |
ncmAlmCfgEnableCardAlmRptThe variable Enable/Disable the alarm reporting for this card.rw Enumeration .1.3.6.1.4.1.321.1.3012.1030.1.13 |
ncmAlmCfgDeclareTimeThe variable specifies the alarm declaration time (in seconds).rw INTEGER .1.3.6.1.4.1.321.1.3012.1030.1.14 |
ncmCURRENTAlarmMsgTable SEQUENCE OF NcmCURRENTAlarmMsgEntry .1.3.6.1.4.1.321.1.3012.1031 |
ncmCURRENTAlarmMsgEntryAn entry in the Current ncm Alarm Message table. NcmCURRENTAlarmMsgEntry .1.3.6.1.4.1.321.1.3012.1031.1 |
ncmCurrAlarmMsgNIDIndexThe object specifies the node id of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1031.1.1 |
ncmCurrAlarmMsgIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1031.1.2 |
ncmCurrAlarmMsgNumberA number between 1 and 15, where 1 is the latest
alarm and 15 is the most recent alarm captured
inside the data base.ro INTEGER .1.3.6.1.4.1.321.1.3012.1031.1.3 |
ncmCurrAlarmMsgEquipIDThe object specifies the Equipment ID of the card.ro INTEGER .1.3.6.1.4.1.321.1.3012.1031.1.4 |
ncmPrevAlarmMsgTable SEQUENCE OF NcmPrevAlarmMsgEntry .1.3.6.1.4.1.321.1.3012.1032 |
ncmPrevAlarmMsgEntryAn entry in the Enhanced ncmAlarm Configure table. NcmPrevAlarmMsgEntry .1.3.6.1.4.1.321.1.3012.1032.1 |
ncmPrevAlarmMsgNIDIndexThe object specifies the node id of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1032.1.1 |
ncmPrevAlarmMsgIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1032.1.2 |
ncmPrevAlarmMsgNumberA number between 1 and 15, where 1 is the latest
alarm and 15 is the most recent alarm captured
inside the data base.ro INTEGER .1.3.6.1.4.1.321.1.3012.1032.1.3 |
ncmPrevAlarmMsgTimeStampSecThe variable specifies the Time Stamp in Seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1032.1.4 |
ncmPrevAlarmMsgTimeStampmsThe variable specifies the Time Stamp in milli Seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1032.1.5 |
ncmPrevAlarmMsgAlarmCodeThe variable specifies the ncm Alarm Code of the card.ro INTEGER .1.3.6.1.4.1.321.1.3012.1032.1.6 |
ncmPrevAlarmMsgAlarmInstanceThe object specifies the ncm Alarm Instance.ro INTEGER (1..'ffffffff'h) .1.3.6.1.4.1.321.1.3012.1032.1.7 |
ncmPrevAlarmMsgObjTypeThe variable specifies the Object Type of the ncmAlarm refer.ro Enumeration .1.3.6.1.4.1.321.1.3012.1032.1.8 |
ncmPrevAlarmMsgSeverityThe variable specifies the severity of the ncm Alarm.ro Enumeration .1.3.6.1.4.1.321.1.3012.1032.1.9 |
ncmEnhanAlmCfgTable SEQUENCE OF NcmEnhanAlmCfgEntry .1.3.6.1.4.1.321.1.3012.1033 |
ncmEnhanAlmCfgEntryAn entry in the Enhanced ncm Alarm Configure table. NcmEnhanAlmCfgEntry .1.3.6.1.4.1.321.1.3012.1033.1 |
ncmEnhanAlmCfgNIDIndexThe object specifies the node id of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1033.1.1 |
ncmEnhanAlmCfgIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1033.1.2 |
ncmEnhanAlmCfgCRCThresholdThe variable specifies the consecutive CRC error threshold
of the port; 0 is to disable this error threshold and 1~31 is
to enable also specify a particular value for this threshold.rw INTEGER .1.3.6.1.4.1.321.1.3012.1033.1.3 |
ncmEnhanAlmCfgSESThresholdThe variable specifies the severly errored seconds threshold
of the port; 0 is to disable this error threshold and 1~100 is
to enable also specify a particular value for this threshold.rw INTEGER .1.3.6.1.4.1.321.1.3012.1033.1.4 |
ncmEnhanAlmCfgUASThresholdThe variable specifies the unavailable seconds threshold
of the port; 0 is to disable this error threshold and 1~100 is
to enable also specify a particular value for this threshold.rw INTEGER .1.3.6.1.4.1.321.1.3012.1033.1.5 |
ncmEnhanAlmCfgBERThresholdThe variable specifies the bit error rate threshold of the
port; the value = 10 Exponential to the power minus n.rw Enumeration .1.3.6.1.4.1.321.1.3012.1033.1.6 |
ncmEnhanAlmCfgBPVThresholdThe object specifies the BPV threshold the port.rw INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1033.1.7 |
ncmEnhanAlmCfgLineRestoralThe variable specifies the Line Restoral mode of the port.rw Enumeration .1.3.6.1.4.1.321.1.3012.1033.1.8 |
ncmEnhanAlmCfgTODHourThe object specifies the Time of day hour the port;
this is the hours to restore line if line restore is TOD.rw INTEGER .1.3.6.1.4.1.321.1.3012.1033.1.9 |
ncmEnhanAlmCfgTODMinuteThe object specifies the Time of day minute the port;
this is the minutes to restore line if line restore is TOD.rw INTEGER .1.3.6.1.4.1.321.1.3012.1033.1.10 |
ncmEnhanAlmCfgLinRestEvalPerThe object specifies the Line Restoral evaulation period (seconds)
of the port.rw INTEGER (0..'ffff'h) .1.3.6.1.4.1.321.1.3012.1033.1.11 |
ncmLoopbackTable SEQUENCE OF NcmLoopbackEntry .1.3.6.1.4.1.321.1.3012.1034 |
ncmLoopbackEntryAn entry in the Loopback Table. NcmLoopbackEntry .1.3.6.1.4.1.321.1.3012.1034.1 |
ncmLpbkNIDIndexThe object specifies the node id of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1034.1.1 |
ncmLpbkLineIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1034.1.2 |
ncmSetAllOnesThe variable Enable/Disable the set all ones loopback option.rw Enumeration .1.3.6.1.4.1.321.1.3012.1034.1.3 |
ncmTimeoutLOCSecThe object specifies the number of seconds to loop for
LOC. 0 for infinite.rw INTEGER (0..'ffff'h) .1.3.6.1.4.1.321.1.3012.1034.1.4 |
ncmRemoteLBThis object specify whether the loopback is remote
or local.rw Enumeration .1.3.6.1.4.1.321.1.3012.1034.1.5 |
ncmActivateDeactLBTypeThis variable represents the loopback confi-
guration of the DS1 interface. Agents support-
ing read/write access should return badValue in
response to a requested loopback state that the
interface does not support. The values mean:
PayloadLoop
The received signal at this interf is
looped through the device. Typically the
received signal is looped back for re-
transmission after it has passed through
the device's framing function.
LineLoop
The received signal at this interface does
not go through the device (minimum pene-
tration) but is looped back out.
LocalLoopbk
This variable indicates whether the
local loopback is enabled or disabled on
the port or line by the device.
DPLoop
This variable indicates whether the
ncmData Port loopback is enabled or disabled
by the device.
Remark: Only ACE-T1/ACE-E1 cards use this loopbk
type for port# 3 & 4; while the QUAD-T1/
QUAD-E1 don't support this loopback type.
Act-LLBBOP
This variable indicates to activate the LLBBOP.
Act-PLBBOP
This variable indicates to activate the PLBBOP.
Deact-LLBBOP
This variable indicates to deactivate the LLBBOP.
Deact-PLBBOP
This variable indicates to deactivate the PLBBOP.
Deact-SIX-TWO-FOUR-ONE-ONE-INBAND
This variable indicates to deactivate 62411 Inband
Deact-FT1-LOOP-CODE
This variable indicates to deactivate FT1 Loop Code
When one of this object is chosen and received by the agent, this loopback
type is send to the target platform to activate the loopback action;
while the object value = 0 is received the loopback action will be deactivated
by the loopback type stored inside the port status.rw Enumeration .1.3.6.1.4.1.321.1.3012.1034.1.6 |
ncmTestPatternTable SEQUENCE OF NcmTestPatternEntry .1.3.6.1.4.1.321.1.3012.1035 |
ncmTestPatternEntryAn entry in the Test Pattern Table. NcmTestPatternEntry .1.3.6.1.4.1.321.1.3012.1035.1 |
ncmTstpattNIDIndexThe object specifies the node id of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1035.1.1 |
ncmTstpattLineIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1035.1.2 |
ncmTstpattTestPeriodThe object specifies the number of seconds to test;
0 for infinite.rw INTEGER (0..'ffff'h) .1.3.6.1.4.1.321.1.3012.1035.1.3 |
ncmStartStopTestPatternWhen one of this object is chosen and received by the agent, this test
pattern is send to the target platform to start the diagnostic action;
while object value = 0, it will stop the test pattern by the pattern
is stored inside the port status.
Remark: Only ACE-T1/ACE-E1 cards use the QRSS test pattern
for data port# 3 & 4; while the QUAD-T1/QUAD-E1 don't
support this test pattern.rw Enumeration .1.3.6.1.4.1.321.1.3012.1035.1.4 |
ncmResetTestCounterThis object reset the test counter in the diagnostic.rw Enumeration .1.3.6.1.4.1.321.1.3012.1035.1.5 |
ncmCircuitInfoTable SEQUENCE OF NcmCircuitInfoEntry .1.3.6.1.4.1.321.1.3012.1036 |
ncmCircuitInfoEntryAn entry in the circuitBuilder Table for adding, editing, deleting,
activate, deactivate and get the detail information of a particular circuit. NcmCircuitInfoEntry .1.3.6.1.4.1.321.1.3012.1036.1 |
ncmCircuitInfoNIDIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1036.1.1 |
ncmCircuitInfoCircNameThis object allocates & indicates the circuit name for sending the
add/edit/delete/activate/deactivate/get detail info circuit
request to the circuitbuilder.rw DisplayString .1.3.6.1.4.1.321.1.3012.1036.1.2 |
ncmCircuitInfoCircPriorityThis object allocates & indicates the circuit priority for sending
the add/edit/get detail info circuit request to the circuitbuilder.rw Enumeration .1.3.6.1.4.1.321.1.3012.1036.1.3 |
ncmCircuitInfoCircTypeThis object allocates & indicates the circuit type for sending
the add/edit/get detail info circuit request to the circuitbuilder.rw Enumeration .1.3.6.1.4.1.321.1.3012.1036.1.4 |
ncmCircuitInfoCircModeThis object allocates & indicates the circuit mode for sending
the add/edit/get detail info circuit request to the circuitbuilder.rw Enumeration .1.3.6.1.4.1.321.1.3012.1036.1.5 |
ncmCircuitInfoSrcPortSiteThis object allocates & indicates the shelf and slot combination of the
source port for sending the add/edit/get detail info circuit request to
the circuitbuilder.rw INTEGER .1.3.6.1.4.1.321.1.3012.1036.1.6 |
ncmCircuitInfoSrcCardEquipIDThis object allocates & indicates the card equipment id of the source port
for sending the add/edit/get detail info circuit request to the circuitbuilder.rw Enumeration .1.3.6.1.4.1.321.1.3012.1036.1.7 |
ncmCircuitInfoSrcPortIDThis object allocates & indicates the port identity of the source port
for sending the add/edit/get detail info circuit request to the circuitbuilder.rw Enumeration .1.3.6.1.4.1.321.1.3012.1036.1.8 |
ncmCircuitInfoSrcTimeslotmapThis object allocates & indicates the timeslot map allocated for the source
port for sending the add/edit/get detail info circuit request to the circuitbuilder.rw INTEGER .1.3.6.1.4.1.321.1.3012.1036.1.9 |
ncmCircuitInfoDstPortSiteThis object allocates & indicates the shelf and slot combination of the
destination port for sending the add/edit/get detail info circuit request
to the circuitbuilder.rw INTEGER .1.3.6.1.4.1.321.1.3012.1036.1.10 |
ncmCircuitInfoDstCardEquipIDThis object allocates & indicates the card equipment id of the destination port
for sending the add/edit/get detail info circuit request to the circuitbuilder.rw Enumeration .1.3.6.1.4.1.321.1.3012.1036.1.11 |
ncmCircuitInfoDstPortIDThis object allocates & indicates the port identity of the destination port
for sending the add/edit/get detail info circuit request to the circuitbuilder.rw Enumeration .1.3.6.1.4.1.321.1.3012.1036.1.12 |
ncmCircuitInfoDstTimeslotmapThis object allocates & indicates the timeslot map allocated for the destination
port for sending the add/edit/get detail info circuit request to the circuitbuilder.rw INTEGER .1.3.6.1.4.1.321.1.3012.1036.1.13 |
ncmCircuitInfoBackPlaneBusIDThis object allocates & indicates the backplane bus ID for sending the
add/edit/get detail info circuit request to the circuitbuilder.rw Enumeration .1.3.6.1.4.1.321.1.3012.1036.1.14 |
ncmCircuitInfoAssoCircNameThis object allocates & indicates the Assoicate circuit name for sending the
add/edit/get detail info circuit request to the circuitbuilder.rw DisplayString .1.3.6.1.4.1.321.1.3012.1036.1.15 |
ncmCircuitInfoActionThe object send the corresponding acp command to execute the specified
circuit action with all necessary parameters setup properly.rw Enumeration .1.3.6.1.4.1.321.1.3012.1036.1.16 |
ncmAddEditActDeactCircuitStatusThis variable indicates the status as the result
of add/edit/Activate/Deactivate circuit.ro Enumeration .1.3.6.1.4.1.321.1.3012.1036.1.17 |
ncmDeleteCircuitStatusThis variable indicates the status as the result
of delete circuit.ro Enumeration .1.3.6.1.4.1.321.1.3012.1036.1.18 |
ncmGetDetailCircuitStatusThis variable indicates the status of the get circuit detail information.ro Enumeration .1.3.6.1.4.1.321.1.3012.1036.1.19 |
ncmPortTimeslotAllocTable SEQUENCE OF NcmPortTimeslotAllocEntry .1.3.6.1.4.1.321.1.3012.1037 |
ncmPortTimeslotAllocEntryAn entry in the Port Timeslot Allocation table for ncmCircuit Build. NcmPortTimeslotAllocEntry .1.3.6.1.4.1.321.1.3012.1037.1 |
ncmPortTimeslotAllocNIDIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1037.1.1 |
ncmPortTimeslotCardSiteThis variable indicates the shelf and slot combination number of the device.rw INTEGER .1.3.6.1.4.1.321.1.3012.1037.1.2 |
ncmPortTimeslotCardEquipIDThis variable indicates the card equipment id of the target.rw Enumeration .1.3.6.1.4.1.321.1.3012.1037.1.3 |
ncmPortTimeslotPortIDThis variable indicates the port identity of the interface.rw Enumeration .1.3.6.1.4.1.321.1.3012.1037.1.4 |
ncmPortAllocTimeSlotMapThe variable indicates the timeslot map allocated for the port by
sending the corresponding acp command to execute the Get Action.ro INTEGER .1.3.6.1.4.1.321.1.3012.1037.1.5 |
ncmDialBkUpInfoTable SEQUENCE OF NcmDialBkUpInfoEntry .1.3.6.1.4.1.321.1.3012.1038 |
ncmDialBkUpInfoEntryAn entry in the retrieval of dial-backup parameter table for ncmCircuit Build. NcmDialBkUpInfoEntry .1.3.6.1.4.1.321.1.3012.1038.1 |
ncmDialBkUpInfoNIDIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1038.1.1 |
ncmDialBkUpReqCircNameThis variable indicates the circuit name for request dial-backup
parameter and retrieve from the circuitbuilder.rw DisplayString .1.3.6.1.4.1.321.1.3012.1038.1.2 |
ncmPrimaryCircNameThis variable indicates the primary circuit name for request
and retrieve from the circuitbuilder as a parameter of dial-backup.rw DisplayString .1.3.6.1.4.1.321.1.3012.1038.1.3 |
ncmBackupCircNameThis variable indicates the backup circuit name for request and
retrieve from the circuitbuilder as a parameter of dial-backup.rw DisplayString .1.3.6.1.4.1.321.1.3012.1038.1.4 |
ncmCallReferenceNumberThe variable indicates the call reference number of the dial-backup.rw INTEGER .1.3.6.1.4.1.321.1.3012.1038.1.5 |
ncmCirSrcPortErrsetupMaskThe variable indicates the bitmap to setup the mask for circuit
source port error of the dial-backup; ncmAlarm Mask ALM-AIS, ALM-YEL
and ALM-LOS are defined for t1 port; whilst ALM-CTS, ALM-DSR and
ALM-DCD are defined for data port.rw Enumeration .1.3.6.1.4.1.321.1.3012.1038.1.6 |
ncmCirDstPortErrsetupMaskThe variable indicates the bitmap to setup the mask for circuit
destination port error of the dial-backup; ncmAlarm Mask ALM-AIS,
ALM-YEL and ALM-LOS are defined for t1 port; whilst ALM-CTS,
ALM-DSR and ALM-DCD are defined for data port.rw Enumeration .1.3.6.1.4.1.321.1.3012.1038.1.7 |
ncmCirErrClearanceMaskThe variable indicates the bitmap to setup the mask for circuit
error clearance of the dial-backup; ncmAlarm Mask ALM-AIS,
ALM-YEL and ALM-LOS are defined for t1 port; whilst ALM-CTS,
ALM-DSR and ALM-DCD are defined for data port.rw Enumeration .1.3.6.1.4.1.321.1.3012.1038.1.8 |
ncmDialBkUpTimeoutThe variable indicates the dial-backup timeout.rw INTEGER .1.3.6.1.4.1.321.1.3012.1038.1.9 |
ncmDialBkUpActionThe object send the corresponding acp command to
execute the dial-backup set action.rw Enumeration .1.3.6.1.4.1.321.1.3012.1038.1.10 |
ncmDialBkUpSetupStatusThis variable indicates the setup status as the result
of set dial-backup parameters.ro Enumeration .1.3.6.1.4.1.321.1.3012.1038.1.11 |
ncmClearCircuitGrpTable SEQUENCE OF NcmClearCircuitGrpEntry .1.3.6.1.4.1.321.1.3012.1039 |
ncmClearCircuitGrpEntryAn entry in the circuitBuilder Table for clearing any circuit group. NcmClearCircuitGrpEntry .1.3.6.1.4.1.321.1.3012.1039.1 |
ncmClearCircuitGrpNIDIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1039.1.1 |
ncmClearCircuitGrpNameThis object allocates the circuit group site for the request.rw Enumeration .1.3.6.1.4.1.321.1.3012.1039.1.2 |
ncmClearCircuitGrpSiteThis object allocates the shelf and slot combination
of the port for the request.rw INTEGER .1.3.6.1.4.1.321.1.3012.1039.1.3 |
ncmClearCircuitCardEquipIDThis object allocate the card equipment id for the request.rw Enumeration .1.3.6.1.4.1.321.1.3012.1039.1.4 |
ncmClearCircuitPortIDThis object allocates the port identity for the request.rw Enumeration .1.3.6.1.4.1.321.1.3012.1039.1.5 |
ncmClearCircuitActionThe object send the corresponding acp command to
execute the clear circuit action.rw Enumeration .1.3.6.1.4.1.321.1.3012.1039.1.6 |
ncmListGetMsgNumTable SEQUENCE OF NcmListGetMsgNumEntry .1.3.6.1.4.1.321.1.3012.1040 |
ncmListGetMsgNumEntryAn entry to retrieve circuit list in a particular page of
the central ncmCircuit Build ncmDatabase. NcmListGetMsgNumEntry .1.3.6.1.4.1.321.1.3012.1040.1 |
ncmListMsgNumNIDIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1040.1.1 |
ncmListMsgNumCircuitGroupccb-CLIST-ALL: List all circuits in the central circuit database.
ccb-CLIST-ACTIVE: List all active circuits in the circuit database.
ccb-CLIST-PORT-CKT: List circuits associated with a port.
ccb-CLIST-CARD-CKT: List circuits associated with a card.
The variable indicates the constant for request to list
which circuit group should be listed from the response.rw Enumeration .1.3.6.1.4.1.321.1.3012.1040.1.2 |
ncmListMsgNumPageNumberThe object allocates the page number for the retrival
of ncmCircuit List request.rw INTEGER .1.3.6.1.4.1.321.1.3012.1040.1.3 |
ncmListMsgNumCardSiteThis object allocates the shelf and slot combination
for the retrival of ncmCircuit List request.rw INTEGER .1.3.6.1.4.1.321.1.3012.1040.1.4 |
ncmListMsgNumCardEquipIDThis object defines the card equipment id of the target.rw Enumeration .1.3.6.1.4.1.321.1.3012.1040.1.5 |
ncmListMsgNumPortIDThis object defines the port identity of the interface.rw Enumeration .1.3.6.1.4.1.321.1.3012.1040.1.6 |
ncmNumofGetListMessageThis variable indicates number of circuits listed in this message.ro INTEGER .1.3.6.1.4.1.321.1.3012.1040.1.7 |
ncmTotalCircDatabaseThis variable indicates total number of circuits in circuit database.ro INTEGER .1.3.6.1.4.1.321.1.3012.1040.1.8 |
ncmCircListccbTable SEQUENCE OF NcmCircListccbEntry .1.3.6.1.4.1.321.1.3012.1041 |
ncmCircListccbEntryAn entry to retrieve the specified circuit detail information as listed
out in the Get List Message Number MIB Group. NcmCircListccbEntry .1.3.6.1.4.1.321.1.3012.1041.1 |
ncmListccbNIDIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1041.1.1 |
ncmNumofCircListMessageThis variable indicates the number of circuit listed in this page.ro INTEGER .1.3.6.1.4.1.321.1.3012.1041.1.2 |
ncmListccbCircNameThis variable indicates the circuit name response from
the circuitbuilder as the circuit identity of the object.ro DisplayString .1.3.6.1.4.1.321.1.3012.1041.1.3 |
ncmListccbCircPriorityThis variable indicates circuit priority of this circuit.ro Enumeration .1.3.6.1.4.1.321.1.3012.1041.1.4 |
ncmListccbCircTypeThis variable indicates circuit type of this circuit.ro Enumeration .1.3.6.1.4.1.321.1.3012.1041.1.5 |
ncmListccbCircModeThis variable indicates circuit mode of this circuit.ro Enumeration .1.3.6.1.4.1.321.1.3012.1041.1.6 |
ncmSrcPortSiteThis variable indicates the shelf and slot combination
of the source port.ro INTEGER .1.3.6.1.4.1.321.1.3012.1041.1.7 |
ncmSrcCardEquipIDThis variable indicates the card equipment id of the source port.ro Enumeration .1.3.6.1.4.1.321.1.3012.1041.1.8 |
ncmSrcPortIdentifierThis variable indicates the port identity of the source port.ro Enumeration .1.3.6.1.4.1.321.1.3012.1041.1.9 |
ncmSrcTimeslotmapThe variable indicates the timeslot map allocated for the source port.ro INTEGER .1.3.6.1.4.1.321.1.3012.1041.1.10 |
ncmDstPortSiteThis variable indicates the shelf and slot combination
of the destination port.ro INTEGER .1.3.6.1.4.1.321.1.3012.1041.1.11 |
ncmDstCardEquipIDThis variable indicates the card equipment id of the destination port.ro Enumeration .1.3.6.1.4.1.321.1.3012.1041.1.12 |
ncmDstPortIdentifierThis variable indicates the port identity of the destination port.ro Enumeration .1.3.6.1.4.1.321.1.3012.1041.1.13 |
ncmDstTimeslotmapThe variable indicates the timeslot map allocated for the destination port.ro INTEGER .1.3.6.1.4.1.321.1.3012.1041.1.14 |
ncmListccbBackPlaneBusIDThe variable indicates the backplane bus ID of the device.ro Enumeration .1.3.6.1.4.1.321.1.3012.1041.1.15 |
ncmListccbCircStatusThis variable indicates the status of the List circuit ccb.ro Enumeration .1.3.6.1.4.1.321.1.3012.1041.1.16 |
ncmEquipmentIDTable SEQUENCE OF NcmEquipmentIDEntry .1.3.6.1.4.1.321.1.3012.1042 |
ncmEquipmentIDEntryAn entry in the Equipment ID table. NcmEquipmentIDEntry .1.3.6.1.4.1.321.1.3012.1042.1 |
ncmEquipmentIDNIDIndexThis variable specifies the node id.ro INTEGER .1.3.6.1.4.1.321.1.3012.1042.1.1 |
ncmEquipmentIDLineIndexThis variable specifies the line index value.ro INTEGER .1.3.6.1.4.1.321.1.3012.1042.1.2 |
ncmFirmwareVersionThe variable specifies the firmware version.ro INTEGER .1.3.6.1.4.1.321.1.3012.1042.1.3 |
ncmFirmwareRevisionThe variable specifies the firmware revision.ro INTEGER .1.3.6.1.4.1.321.1.3012.1042.1.4 |
ncmEquipmentTypeThe variable specifies the Equipment Type.ro INTEGER .1.3.6.1.4.1.321.1.3012.1042.1.5 |
ncmHardwareVersionThe variable specifies the hardware version.ro INTEGER .1.3.6.1.4.1.321.1.3012.1042.1.6 |
ncmHardwareRevisionThe variable specifies the hardwareware revision.ro INTEGER .1.3.6.1.4.1.321.1.3012.1042.1.7 |
ncmLocationIDThe variable specifies the Location ID.ro INTEGER .1.3.6.1.4.1.321.1.3012.1042.1.8 |
ncmE1AlarmThresholdConfigTable SEQUENCE OF NcmE1AlarmThresholdConfigEntry .1.3.6.1.4.1.321.1.3012.1043 |
ncmE1AlarmThresholdConfigEntryAn entry in the E1 ncmAlarm Threshold Configure table. NcmE1AlarmThresholdConfigEntry .1.3.6.1.4.1.321.1.3012.1043.1 |
ncmE1AlarmThresholdConfigNIDIndexThe object specifies the node id of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1043.1.1 |
ncmE1AlarmThresholdConfigIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.2 |
ncmE1LOFThresholdThis variable specifies the LOF Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.3 |
ncmE1LOFTimeIntervalThis variable specifies the LOF Time Interval in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.4 |
ncmE1LOSThresholdThis variable specifies the LOS Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.5 |
ncmE1LOSTimeIntervalThis variable specifies the LOS Time Interval in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.6 |
ncmE1RAIThresholdThis variable specifies the RAI Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.7 |
ncmE1RAITimeIntervalThis variable specifies the RAI Time Interval in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.8 |
ncmE1AISThresholdThis variable specifies the AIS Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.9 |
ncmE1AISTimeIntervalThis variable specifies the AIS Time Interval in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.10 |
ncmE1BPVThresholdThis variable specifies the BPV Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.11 |
ncmE1BPVTimeIntervalThis variable specifies the BPV Time Interval in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.12 |
ncmE1ES15MINThresholdThis variable specifies the ES 15 minute Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.13 |
ncmE1ES24HRThresholdThis variable specifies the ES 24 hour Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.14 |
ncmE1SES15MINThresholdThis variable specifies the SES 15 minute Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.15 |
ncmE1SES24HRThresholdThis variable specifies the SES 24 hour Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.16 |
ncmCVP15MINThresholdThis variable specifies the CVP 15 minute Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.17 |
ncmCVP24HRThresholdThis variable specifies the CVP 24 hour Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.18 |
ncmCVL15MINThresholdThis variable specifies the CVL 15 minute Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.19 |
ncmCVL24HRThresholdThis variable specifies the CVL 24 hour Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.20 |
ncmESL15MINThresholdThis variable specifies the ESL 15 minute Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.21 |
ncmESL24HRThresholdThis variable specifies the CVL 24 hour Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.22 |
ncmSESL15MINThresholdThis variable specifies the SESL 15 minute Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.23 |
ncmSESL24HRThresholdThis variable specifies the SESL 24 hour Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.24 |
ncmUASP15MINThresholdThis variable specifies the UASP 15 minute Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.25 |
ncmUASP24HRThresholdThis variable specifies the UASP 24 hour Threshold count in secs.rw INTEGER .1.3.6.1.4.1.321.1.3012.1043.1.26 |
ncmE1AlarmThresholdStatusTable SEQUENCE OF NcmE1AlarmThresholdStatusEntry .1.3.6.1.4.1.321.1.3012.1044 |
ncmE1AlarmThresholdStatusEntryAn entry in the E1 ncmAlarm Threshold Status table. NcmE1AlarmThresholdStatusEntry .1.3.6.1.4.1.321.1.3012.1044.1 |
ncmE1AlarmThresholdStatusNIDIndexThe object specifies the node id of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1044.1.1 |
ncmE1AlarmThresholdStatusIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.2 |
ncmLOFExceededE1This variable specifies if LOF exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.3 |
ncmLOSExceededE1This variable specifies if LOS exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.4 |
ncmRAIExceededE1This variable specifies if RAI exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.5 |
ncmAISExceededE1This variable specifies if AIS exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.6 |
ncmBPVExceededE1This variable specifies if BPV exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.7 |
ncmES15MINExceededThis variable specifies if ES 15 minute exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.8 |
ncmES24HRExceededThis variable specifies if ES 24 Hour exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.9 |
ncmSES15MINExceededThis variable specifies if SES 15 minute exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.10 |
ncmSES24HRExceededThis variable specifies if SES 24 Hour exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.11 |
ncmCVP15MINExceededThis variable specifies if CVP 15 minute exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.12 |
ncmCVP24HRExceededThis variable specifies if CVP 24 Hour exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.13 |
ncmCVL15MINExceededThis variable specifies if CVL 15 minute exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.14 |
ncmCVL24HRExceededThis variable specifies if CVL 24 Hour exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.15 |
ncmESL15MINExceededThis variable specifies if ESL 15 minute exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.16 |
ncmESL24HRExceededThis variable specifies if ESL 24 Hour exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.17 |
ncmSESL15MINExceededThis variable specifies if SESL 15 minute exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.18 |
ncmSESL24HRExceededThis variable specifies if SESL 24 Hour exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.19 |
ncmUASP15MINExceededThis variable specifies if UASP 15 minute exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.20 |
ncmUASP24HRExceededThis variable specifies if UASP 24 Hour exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1044.1.21 |
ncmLOFThresholdCountThis variable specifies the LOF Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.22 |
ncmLOFTimeIntervalsThis variable specifies the LOF Time Intervals in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.23 |
ncmLOSThresholdCountThis variable specifies the LOS Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.24 |
ncmLOSTimeIntervalsThis variable specifies the LOS Time Intervals in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.25 |
ncmRAIThresholdCountThis variable specifies the RAI Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.26 |
ncmRAITimeIntervalsThis variable specifies the RAI Time Intervals in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.27 |
ncmAISThresholdCountThis variable specifies the AIS Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.28 |
ncmAISTimeIntervalsThis variable specifies the AIS Time Intervals in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.29 |
ncmBPVThresholdCountThis variable specifies the BPV Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.30 |
ncmBPVTimeIntervalsThis variable specifies the BPV Time Intervals in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.31 |
ncmES15MINThresholdCountThis variable specifies the ES 15MIN Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.32 |
ncmES24HRThresholdCountThis variable specifies the ES 24HR Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.33 |
ncmSES15MINThresholdCountThis variable specifies the SES 15MIN Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.34 |
ncmSES24HRThresholdCountThis variable specifies the SES 24 HR Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.35 |
ncmCVP15MINThresholdCountThis variable specifies the CVP 15MIN Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.36 |
ncmCVP24HRThresholdCountThis variable specifies the CVP 24 HR Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.37 |
ncmCVL15MINThresholdCountThis variable specifies the CVL 15MIN Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.38 |
ncmCVL24HRThresholdCountThis variable specifies the CVL 24 HR Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.39 |
ncmESL15MINThresholdCountThis variable specifies the ESL 15MIN Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.40 |
ncmESL24HRThresholdCountThis variable specifies the ESL 24 HR Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.41 |
ncmSESL15MINThresholdCountThis variable specifies the SESL 15MIN Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.42 |
ncmSESL24HRThresholdCountThis variable specifies the SESL 24 HR Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.43 |
ncmUASP15MINThresholdCountThis variable specifies the UASP 15MIN Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.44 |
ncmUASP24HRThresholdCountThis variable specifies the UASP 24 HR Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1044.1.45 |
ncmAlarmThresholdConfigTable SEQUENCE OF NcmAlarmThresholdConfigEntry .1.3.6.1.4.1.321.1.3012.1045 |
ncmAlarmThresholdConfigEntryAn entry in the ncmAlarm Threshold Configure table. NcmAlarmThresholdConfigEntry .1.3.6.1.4.1.321.1.3012.1045.1 |
ncmAlarmThresholdConfigNIDIndexThe object specifies the node id of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1045.1.1 |
ncmAlarmThresholdConfigIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER .1.3.6.1.4.1.321.1.3012.1045.1.2 |
ncmLOFThresholdThis variable the LOF Threshold count is seconds (1-86,400).rw INTEGER .1.3.6.1.4.1.321.1.3012.1045.1.3 |
ncmLOFTimeIntervalThis variable specifies the LOF Time Interval is seconds (1-86,400).rw INTEGER .1.3.6.1.4.1.321.1.3012.1045.1.4 |
ncmLOSThresholdThis variable specifies the LOS Threshold count is seconds (1-86,400).rw INTEGER .1.3.6.1.4.1.321.1.3012.1045.1.5 |
ncmLOSTimeIntervalThis variable specifies the LOS Time Interval is seconds (1-86,400).rw INTEGER .1.3.6.1.4.1.321.1.3012.1045.1.6 |
ncmRAIThresholdThis variable specifies the RAI Threshold count is seconds (1-86,400).rw INTEGER .1.3.6.1.4.1.321.1.3012.1045.1.7 |
ncmRAITimeIntervalThis variable specifies the RAI Time Interval is seconds (1-86,400).rw INTEGER .1.3.6.1.4.1.321.1.3012.1045.1.8 |
ncmAISThresholdThis variable specifies the AIS Threshold count is seconds (1-86,400).rw INTEGER .1.3.6.1.4.1.321.1.3012.1045.1.9 |
ncmAISTimeIntervalThis variable specifies the AIS Time Interval is seconds (1-86,400).rw INTEGER .1.3.6.1.4.1.321.1.3012.1045.1.10 |
ncmBPVThresholdThis variable specifies the BPV Threshold count is seconds (1-86,400).rw INTEGER .1.3.6.1.4.1.321.1.3012.1045.1.11 |
ncmBPVTimeIntervalThis variable specifies the BPV Time Interval is seconds (1-86,400).rw INTEGER .1.3.6.1.4.1.321.1.3012.1045.1.12 |
ncmES15MINThresholdThis variable specifies the ES 15 minute Threshold count is seconds (1-86,400).rw INTEGER .1.3.6.1.4.1.321.1.3012.1045.1.13 |
ncmES24HRThresholdThis variable specifies the ES 24 hour Threshold count in seconds (1-86,400).rw INTEGER .1.3.6.1.4.1.321.1.3012.1045.1.14 |
ncmSES15MINThresholdThis variable specifies the SES 15 minute Threshold count is seconds (1-86,400).rw INTEGER .1.3.6.1.4.1.321.1.3012.1045.1.15 |
ncmSES24HRThresholdThis variable specifies the SES 24 hour Threshold count in seconds (1-86,400).rw INTEGER .1.3.6.1.4.1.321.1.3012.1045.1.16 |
ncmAlarmThresholdStatusTable SEQUENCE OF NcmAlarmThresholdStatusEntry .1.3.6.1.4.1.321.1.3012.1046 |
ncmAlarmThresholdStatusEntryAn entry in the ncmAlarm Threshold Status table. NcmAlarmThresholdStatusEntry .1.3.6.1.4.1.321.1.3012.1046.1 |
ncmAlarmThresholdStatusNIDIndexThe object specifies the node id of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1046.1.1 |
ncmAlarmThresholdStatusIndexThe index value which uniquely identifies the
interface to which this entry is applicable.ro INTEGER .1.3.6.1.4.1.321.1.3012.1046.1.2 |
ncmLOFExceededThis variable specifies if LOF exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1046.1.3 |
ncmLOSExceededThis variable specifies if LOS exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1046.1.4 |
ncmAISExceededThis variable specifies if AIS exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1046.1.5 |
ncmRAIExceededThis variable specifies if RAI exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1046.1.6 |
ncmBPVExceededThis variable specifies if BPV exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1046.1.7 |
ncmESExceededThis variable specifies if ES exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1046.1.8 |
ncmSESExceededThis variable specifies if SES exceeded or not.ro Enumeration .1.3.6.1.4.1.321.1.3012.1046.1.9 |
ncmLOFThresholdCountstThis variable specifies the LOF Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1046.1.10 |
ncmLOFTimeIntervalstThis variable specifies the LOF Time Intervals in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1046.1.11 |
ncmLOSThresholdCountstThis variable specifies the LOS Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1046.1.12 |
ncmLOSTimeIntervalstThis variable specifies the LOS Time Intervals in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1046.1.13 |
ncmRAIThresholdCountstThis variable specifies the RAI Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1046.1.14 |
ncmRAITimeIntervalstThis variable specifies the RAI Time Intervals in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1046.1.15 |
ncmAISThresholdCountstThis variable specifies the AIS Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1046.1.16 |
ncmAISTimeIntervalstThis variable specifies the AIS Time Intervals in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1046.1.17 |
ncmBPVThresholdCountstThis variable specifies the BPV Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1046.1.18 |
ncmBPVTimeIntervalstThis variable specifies the BPV Time Intervals in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1046.1.19 |
ncmES15MINThresholdCountstThis variable specifies the ES 15 minute Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1046.1.20 |
ncmES24HRThresholdCountstThis variable specifies the ES 24 Hour Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1046.1.21 |
ncmSES15MINThresholdCountstThis variable specifies the SES 15 minute Threshold Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1046.1.22 |
ncmSES24HRThresholdCountstThis variable specifies the SES 24 hour Count in seconds.ro INTEGER .1.3.6.1.4.1.321.1.3012.1046.1.23 |
ncmResetAlmThresholdCountThis object reset the alarm threshold counter.rw Enumeration .1.3.6.1.4.1.321.1.3012.1046.1.24 |
ncmShelfSyncSourceSegTable SEQUENCE OF NcmShelfSyncSourceSegEntry .1.3.6.1.4.1.321.1.3012.1050 |
ncmShelfSyncSourceSegEntryAn entry in the ncm Shelf Sync Source Segment Time table. NcmShelfSyncSourceSegEntry .1.3.6.1.4.1.321.1.3012.1050.1 |
ncmShelfSyncSegNIDIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1050.1.1 |
ncmShelfSyncSourceSegIndexThis object is the identifier of an Interface
on a managed device. If there is an ifEntry
that is directly associated with this and
only this DS1 interface, it should have the
same value as ifIndex. Otherwise, the value
exceeds ifNumber, and is a unique identifier
following this rule: inside interfaces (e.g.,
equipment side) with even numbers and outside
interfaces (e.g., network side) with odd
numbers.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1050.1.2 |
ncmShelfSyncSourceSegNumThis variable indicates the segment index.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3012.1050.1.3 |
ncmShelfTypeSegThis variable indicates the shelf hardware type.ro Enumeration .1.3.6.1.4.1.321.1.3012.1050.1.4 |
ncmRefBusSegThis variable indicates the reference bus of the segment.rw Enumeration .1.3.6.1.4.1.321.1.3012.1050.1.5 |
ncmSourceSegOneShelfNumThis variable indicates the source one shelf number of
the segment.rw INTEGER .1.3.6.1.4.1.321.1.3012.1050.1.6 |
ncmSourceSegOneCardNumThis variable indicates the source one card number of the
segment.rw INTEGER .1.3.6.1.4.1.321.1.3012.1050.1.7 |
ncmSourceSegOneClockRefThis variable indicates the source one clock reference of
the segment.rw Enumeration .1.3.6.1.4.1.321.1.3012.1050.1.8 |
ncmSourceSegAutoRestore1This variable indicates the source one auto restore of the
segment.rw Enumeration .1.3.6.1.4.1.321.1.3012.1050.1.9 |
ncmSourceSegTwoShelfNumThis variable indicates the source two shelf number of the
segment.rw INTEGER .1.3.6.1.4.1.321.1.3012.1050.1.10 |
ncmSourceSegTwoCardNumThis variable indicates the source two card number of the
segment.rw INTEGER .1.3.6.1.4.1.321.1.3012.1050.1.11 |
ncmSourceSegTwoClockRefThis variable indicates the source two clock reference of the
segment.rw Enumeration .1.3.6.1.4.1.321.1.3012.1050.1.12 |
ncmSourceSegAutoRestore2This variable indicates the source two auto restore of
the segment.rw Enumeration .1.3.6.1.4.1.321.1.3012.1050.1.13 |
ncmSourceSegThreeShelfNumThis variable indicates the source three shelf number of
the segment.rw INTEGER .1.3.6.1.4.1.321.1.3012.1050.1.14 |
ncmSourceSegThreeCardNumThis variable indicates the source three card number of
the segment.rw INTEGER .1.3.6.1.4.1.321.1.3012.1050.1.15 |
ncmSourceSegThreeClockRefThis variable indicates the source three clock reference of
the segment.rw Enumeration .1.3.6.1.4.1.321.1.3012.1050.1.16 |
ncmSourceSegAutoRestore3This variable indicates the source three auto restore of
the segment.rw Enumeration .1.3.6.1.4.1.321.1.3012.1050.1.17 |
ncmShelfCurrentSyncSourceSegThis variable indicates the current sync source of the segment.rw Enumeration .1.3.6.1.4.1.321.1.3012.1050.1.18 |
ncmNodeCurrEntryAn entry in the ncmNode Current table
for selecting the active node in operation. NcmNodeCurrEntry .ncmNodeCurrTable.1 |
ncmNodeCurrIndexThis variable indicates the node id
value inside the array containing all called nodes.ro INTEGER (1..'7fffffff'h) .ncmNodeCurrTable.1.1 |
ncmNodeCurrAddressThis variable indicates the ncmNode Current Address.ro DisplayString (SNMPv2-TC) .ncmNodeCurrTable.1.2 |
ncmActiveNodeStatusThis variable indicates what is the current node of the
network that is being managed; when this object is set,
another node table will be activated and treat as active.rw Enumeration .ncmNodeCurrTable.1.3 |