VERILINK-ENTERPRISE-NCMDSU-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for VERILINK-ENTERPRISE-NCMDSU-MIB.
86
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
86 total| Object Name |
|---|
RFC1213-MIBThe ncmdsu information table. SEQUENCE OF NcmdsuCommonEntry .1.3.6.1.4.1.321.1.3022.2000 |
ncmdsuConfigTableThe ncmdsu Configuration table. SEQUENCE OF NcmdsuConfigEntry .1.3.6.1.4.1.321.1.3022.2001 |
ncmdsuConfigEntryAn entry in the ncmdsu Configuration table. NcmdsuConfigEntry .1.3.6.1.4.1.321.1.3022.2001.1 |
ncmdsuNIDConfigIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3022.2001.1.1 |
ncmdsuLineIndexro INTEGER .1.3.6.1.4.1.321.1.3022.2001.1.2 |
ncmdsubusThe ncmdsu bus type for Port.rw Enumeration .1.3.6.1.4.1.321.1.3022.2001.1.3 |
ncmdsuPortChannelThis variable indicates the channel assignment for the
ncmdsu for the port.rw DisplayString .1.3.6.1.4.1.321.1.3022.2001.1.4 |
ncmdsuPortConfigurationThis variable indicates the configuration bits
for port. The configuration can be set by setting the relevant
bit to 1 and reset by setting the relevant bit to zero.
Bit Value Name Description
0 set the ncmdsu port configuration to zero
0 1 64k set uses 8bits of data/64kbps.
1 2 LEN set enable loop code and loop commands
2 4 INV set invert the channelized data
3 8 SCR set to scramble channelized data.
4 16 CLK1 DTE transmit clock select bits
5 32 CLK2 DTE transmit clock select bits
6 64 TU set port as a timing unit
7 128 ALM set if DIU has to report alarms to SAM.rw INTEGER .1.3.6.1.4.1.321.1.3022.2001.1.5 |
ncmcsushelfThis variable indicates the csu shelf associated with
the ncmdsu port.rw INTEGER .1.3.6.1.4.1.321.1.3022.2001.1.6 |
ncmcsuslotThis variable indicates the csu slot associated with
the ncmdsu port.rw INTEGER .1.3.6.1.4.1.321.1.3022.2001.1.7 |
ncmdsuAlarmEnableThis variable indicates whether the alarm is enabled or disabled for ncmdsu.rw Enumeration .1.3.6.1.4.1.321.1.3022.2001.1.8 |
ncmdsuLosLeadThis variable indicates the DTE lead bits
for port. The DTE leads can be set by setting the relevant
bit to 1 and reset by setting the relevant bit to zero.
Bit Value Name Description
0 set the ncmdsu port configuration to zero
0 1 DTR set uses DTR
1 2 RTS set uses RTS
2 4 DSR set uses DSR
3 8 CTS set uses CTS
4 16 DCD set uses DCD
5 32 LOS use both bits: bits set to use for alarm
6 64 LOS 0 = Disable LOS detect, 1=use RTS , 2 = DTR
7 128 DDSMode set for 56k DDS .rw INTEGER .1.3.6.1.4.1.321.1.3022.2001.1.9 |
ncmdsuTimingSourceThis variable indicates the T1 timing source for ncmdsu.rw Enumeration .1.3.6.1.4.1.321.1.3022.2001.1.10 |
ncmdsuDTESpeedThis variable indicates DTE Speed control and speeds 38.4k or below holds good for the DIU2131 card type.rw Enumeration .1.3.6.1.4.1.321.1.3022.2001.1.11 |
ncmdsustatTableThe ncm dsu stat table. SEQUENCE OF NcmdsustatEntry .1.3.6.1.4.1.321.1.3022.2003 |
ncmdsustatEntryAn entry in the ncm dsu stat table. NcmdsustatEntry .1.3.6.1.4.1.321.1.3022.2003.1 |
ncmdsuNIDstatIndexThis object specifies the node id of the node.ro INTEGER .1.3.6.1.4.1.321.1.3022.2003.1.1 |
ncmdsustatIndexro INTEGER .1.3.6.1.4.1.321.1.3022.2003.1.2 |
ncmdsuPortLowbatteryThe ncmdsu Lowbattery status for Port.ro Enumeration .1.3.6.1.4.1.321.1.3022.2003.1.3 |
ncmdsuPortLOSstatusThe ncmdsu LOS status for Port.ro Enumeration .1.3.6.1.4.1.321.1.3022.2003.1.4 |
ncmdsuPortblockerrorcounterThe number of block errors produced on port.ro Gauge .1.3.6.1.4.1.321.1.3022.2003.1.5 |
ncmdsuPortTestSecondsThe number of errors produced by a test on port.ro Gauge .1.3.6.1.4.1.321.1.3022.2003.1.6 |
ncmdsuPortrateper8000The rate/8000 on port.ro INTEGER .1.3.6.1.4.1.321.1.3022.2003.1.7 |
ncmdsuPortLeadStatus1This variable indicates the Lead Status (part 1)
of the port.
The various bit positions are:
Bit Value Name
0 1 DTR (1 = on; 0 = off)
1 2 RTS
2 4 DSR
3 8 CTS
4 16 DCD
5 32 TXD
6 64 RXD
7 128 Lead status available bit.ro INTEGER .1.3.6.1.4.1.321.1.3022.2003.1.8 |
ncmdsuPortLeadStatus2This variable indicates the Lead Status (part 2)
of the port.The lead status2 is bit mapped.
The various bit positions are:
BIT Value Name
0 0 no-loop
0 1 local-loop
1 2 remote-loop
2 4 test-mode.ro INTEGER .1.3.6.1.4.1.321.1.3022.2003.1.9 |
ncmdbuPrimaryLineStatusThis variable indicates the Primary Line Status of the ncmdbu.ro Enumeration .1.3.6.1.4.1.321.1.3022.2003.1.10 |
ncmdbuLineStatusThis variable indicates the ncmdbu Line Status of the ncmdbu.ro Enumeration .1.3.6.1.4.1.321.1.3022.2003.1.11 |
ncmdbuSwitchByThis variable indicates the cause of the ncmdbu switching.ro Enumeration .1.3.6.1.4.1.321.1.3022.2003.1.12 |
ncmdbuReceivedCodeThis variable indicates the ncmdbu received code in hex.ro INTEGER .1.3.6.1.4.1.321.1.3022.2003.1.13 |
ncmdsuPortTestResultsThe number of errors produced by a test on port .ro INTEGER .1.3.6.1.4.1.321.1.3022.2003.1.14 |
ncmdsuPortDiagStatusThis variable indicates the Diagnostic Status
of the port.
The various bit positions are:
Bit Value Name
0 1 Reserved
1 2 Reserved
2 4 Reserved
3 8 Sending Test Code
4 16 Sending loopdown code
5 32 Sending loopup code
6 64 far end looped
7 128 Near end looped.ro INTEGER .1.3.6.1.4.1.321.1.3022.2003.1.15 |
ncmdbuMainConfigTableThe ncm dbu Main Configuration table. SEQUENCE OF NcmdbuMainConfigEntry .1.3.6.1.4.1.321.1.3023.4000 |
ncmdbuMainConfigEntryAn entry in the ncm dbu Main Configuration table. NcmdbuMainConfigEntry .1.3.6.1.4.1.321.1.3023.4000.1 |
ncmdbuNIDMainConfigIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3023.4000.1.1 |
ncmdbuMainLineIndexro INTEGER .1.3.6.1.4.1.321.1.3023.4000.1.2 |
ncmdbudsubusThe ncmdsu bus type for Port.rw Enumeration .1.3.6.1.4.1.321.1.3023.4000.1.3 |
ncmdbuPortChannelThis variable indicates the channel assignment for the
ncmdbu for the port.rw DisplayString .1.3.6.1.4.1.321.1.3023.4000.1.4 |
ncmdbuPortConfigurationThis variable indicates the configuration bits
for port. The configuration can be set by setting the relevant
bit to 1 and reset by setting the relevant bit to zero.
Bit Value Name Description
0 set the ncmdsu port configuration to zero
0 1 64k set uses 8bits of data/64kbps.
1 2 LEN set enable loop code and loop commands
2 4 INV set invert the channelized data
3 8 SCR set to scramble channelized data.
4 16 CLK1 DTE transmit clock select bits
5 32 CLK2 DTE transmit clock select bits
6 64 TU set port as a timing unit
7 128 ALM set if DIU has to report alarms to SAM.rw INTEGER .1.3.6.1.4.1.321.1.3023.4000.1.5 |
ncmdbucsushelfThis variable indicates the csu shelf associated with
the ncmdbu port.rw INTEGER .1.3.6.1.4.1.321.1.3023.4000.1.6 |
ncmdbucsuslotThis variable indicates the csu slot associated with
the ncmdbu port.rw INTEGER .1.3.6.1.4.1.321.1.3023.4000.1.7 |
ncmdbuLosLeadThis variable indicates the DTE lead bits
for port. The DTE leads can be set by setting the relevant
bit to 1 and reset by setting the relevant bit to zero.
Bit Value Name Description
0 set the ncmdsu port configuration to zero
0 1 DTR set uses DTR
1 2 RTS set uses RTS
2 4 DSR set uses DSR
3 8 CTS set uses CTS
4 16 DCD set uses DCD
5 32 LOS use both bits: bits set to use for alarm
6 64 LOS 0 = Disable LOS detect, 1=use RTS , 2 = DTR
7 128 DDSMode set for 56k DDS .rw INTEGER .1.3.6.1.4.1.321.1.3023.4000.1.8 |
ncmdbuConfigTableThe ncm dbu Configuration table. SEQUENCE OF NcmdbuConfigEntry .1.3.6.1.4.1.321.1.3023.4001 |
ncmdbuConfigEntryAn entry in the ncmdbu Configuration table. NcmdbuConfigEntry .1.3.6.1.4.1.321.1.3023.4001.1 |
ncmdbuNIDConfigIndexThis variable specifies the node id.ro INTEGER .1.3.6.1.4.1.321.1.3023.4001.1.1 |
ncmdbuLineIndexro INTEGER .1.3.6.1.4.1.321.1.3023.4001.1.2 |
ncmdbuAllOnesSwitchOverTimeThis variable indicates the all ones duration in seconds for
the ncmdbu.rw INTEGER .1.3.6.1.4.1.321.1.3023.4001.1.3 |
ncmdbuSwitchOnBERThresholdExceededThis variable indicates whether the ncmdbu is switched on for BER Threshold
exceeded.rw Enumeration .1.3.6.1.4.1.321.1.3023.4001.1.4 |
ncmdbuDialBackupModeThis variable indicates the dial backup mode for the ncmdbu.rw Enumeration .1.3.6.1.4.1.321.1.3023.4001.1.5 |
ncmdbuBackupConnectionThis variable indicates the whether the backup connection is activated or not.rw Enumeration .1.3.6.1.4.1.321.1.3023.4001.1.6 |
ncmdbumodeThis variable specifies the mode of ncmdbu.rw Enumeration .1.3.6.1.4.1.321.1.3023.4001.1.7 |
ncmdbuLoopTypeThis variable specifies the Loop Type on RL EIA .rw Enumeration .1.3.6.1.4.1.321.1.3023.4001.1.8 |
ncmddsMainConfigTableThe ncmdds Main Configuration table. SEQUENCE OF NcmddsMainConfigEntry .1.3.6.1.4.1.321.1.3024.5000 |
ncmddsMainConfigEntryAn entry in the ncmdds Main Configuration table. NcmddsMainConfigEntry .1.3.6.1.4.1.321.1.3024.5000.1 |
ncmddsNIDMainConfigIndexThis variable indicates the node id
value of the node.ro INTEGER (1..'7fffffff'h) .1.3.6.1.4.1.321.1.3024.5000.1.1 |
ncmddsMainLineIndexro INTEGER .1.3.6.1.4.1.321.1.3024.5000.1.2 |
ncmddsdsubusThe ncmdsu bus type for Port.rw Enumeration .1.3.6.1.4.1.321.1.3024.5000.1.3 |
ncmddsPortChannelThis variable indicates the channel assignment for the
ncmdsu for the port.rw DisplayString .1.3.6.1.4.1.321.1.3024.5000.1.4 |
ncmddsPortConfigurationThis variable indicates the configuration bits
for port. The configuration can be set by setting the relevant
bit to 1 and reset by setting the relevant bit to zero.
Bit Value Name Description
0 set the ncmdsu port configuration to zero
0 1 64k set uses 8bits of data/64kbps.
1 2 LEN set enable loop code and loop commands
2 4 INV set invert the channelized data
3 8 SCR set to scramble channelized data.
4 16 CLK1 DTE transmit clock select bits
5 32 CLK2 DTE transmit clock select bits
6 64 TU set port as a timing unit
7 128 ALM set if DIU has to report alarms to SAM.rw INTEGER .1.3.6.1.4.1.321.1.3024.5000.1.5 |
ncmddscsushelfThis variable indicates the csu shelf associated with
the ncmdsu port.rw INTEGER .1.3.6.1.4.1.321.1.3024.5000.1.6 |
ncmddscsuslotThis variable indicates the csu slot associated with
the ncmdsu port.rw INTEGER .1.3.6.1.4.1.321.1.3024.5000.1.7 |
ncmddsLosLeadThis variable indicates the DTE lead bits
for port. The DTE leads can be set by setting the relevant
bit to 1 and reset by setting the relevant bit to zero.
Bit Value Name Description
0 set the ncmdsu port configuration to zero
0 1 DTR set uses DTR
1 2 RTS set uses RTS
2 4 DSR set uses DSR
3 8 CTS set uses CTS
4 16 DCD set uses DCD
5 32 LOS use both bits: bits set to use for alarm
6 64 LOS 0 = Disable LOS detect, 1=use RTS , 2 = DTR
7 128 DDSMode set for 56k DDS .rw INTEGER .1.3.6.1.4.1.321.1.3024.5000.1.8 |
ncmddsConfigTableThe ncmdds Configuration table. SEQUENCE OF NcmddsConfigEntry .1.3.6.1.4.1.321.1.3024.5001 |
ncmddsConfigEntryAn entry in the ncmdds Configuration table. NcmddsConfigEntry .1.3.6.1.4.1.321.1.3024.5001.1 |
ncmddsNIDConfigIndexThis variable specifies the node id.ro INTEGER .1.3.6.1.4.1.321.1.3024.5001.1.1 |
ncmddsConfigLineIndexThis variable specifies the Line index.ro INTEGER .1.3.6.1.4.1.321.1.3024.5001.1.2 |
ncmddsPortLoopEnableThis variable indicates the loop enable bits
for port. The loop enable can be set by setting the relevant
bit to 1 and reset by setting the relevant bit to zero.
Bit Value Description
0 no-loop
0 1 enable ncmdds loop
1 2 enable v54 loop
2 4 enable ft1 loop
3 8 enable verilink loop
4 16
5 32
6 64
7 128 .rw Enumeration .1.3.6.1.4.1.321.1.3024.5001.1.3 |
ncmddsPortReceiveLoopCodeThis variable indicates the Receive ncmdds loop code
of the port 1.rw Enumeration .1.3.6.1.4.1.321.1.3024.5001.1.4 |
ncmddsPortRemoteLoopCodeThis variable indicates the Receive ncmdds loop code
of the port.rw Enumeration .1.3.6.1.4.1.321.1.3024.5001.1.5 |
ncmddsPortAlarmEnableThis variable indicates the Alarm enable which is bit mapped
of the port.
BIT Value Description
0 0 no-loop
0 1 alarm-on-loop
1 2 alarm-on-test
3 bothrw Enumeration .1.3.6.1.4.1.321.1.3024.5001.1.6 |
ncmddsPortAlarmClearDelayTimeThis variable indicates the Alarmcleardelaytime
of the port.rw INTEGER .1.3.6.1.4.1.321.1.3024.5001.1.7 |
ncmddsPortAbnormalStationCodeThresholdThis variable indicates the AbnormalStationCodethreshold
of the port.rw INTEGER .1.3.6.1.4.1.321.1.3024.5001.1.8 |
ncmddsPortControlModeIdleThresholdThis variable indicates the ControlModeIdlethreshold
of the port.rw INTEGER .1.3.6.1.4.1.321.1.3024.5001.1.9 |
ncmddsPortMuxOutofSyncThresholdThis variable indicates the MuxoutofSyncthreshold
of the port.rw INTEGER .1.3.6.1.4.1.321.1.3024.5001.1.10 |
ncmddsPortUnAssignedMuxChannelThresholdThis variable indicates the UnassignedMuxChannelthreshold
of the port.rw INTEGER .1.3.6.1.4.1.321.1.3024.5001.1.11 |
ncmddsPortGroup1CodesThis variable indicates the port1Group1ncmddsCodes
of the port.rw INTEGER .1.3.6.1.4.1.321.1.3024.5001.1.12 |
ncmddsPort56KStatusThis variable indicates the 56K ncmdds Status
of the port.
The various bit positions are:
0 Abnormal Station code(1 = Yes, 0 = No)
1 Control Mode Idle
2 Mux-Out-of-Sync
3 Unassigned Mux Chan
4 Group 1 ncmdds Codes Test Test
5 Test in Progress { 0 } Verilink {0} 511
6 Test in Progress { 0 } {1}
7 ncmdds mode enabledro INTEGER .1.3.6.1.4.1.321.1.3024.5001.1.13 |
ncmddsPortReceived56KCodeThis variable specifies the received 56K ncmdds code.Some specitic
values indicate the specific testing error.
Value Testing Error
1 UMC
2 TIP
3 TA
4 MA
5 RC
6 BL
7 LBE
8 FEV
9 ASC
10 OOS
11 CMI
12 TCro Enumeration .1.3.6.1.4.1.321.1.3024.5001.1.14 |
ncmddsmodeThis variable specifies the mode of ncmdds.rw Enumeration .1.3.6.1.4.1.321.1.3024.5001.1.15 |
ncmddsLatchingLoopbackTypeThis variable specifies the latching loop up type of dds.rw Enumeration .1.3.6.1.4.1.321.1.3024.5001.1.16 |
ncmddsLatchingLoopbackDevNoThis variable specifies the device number to receive code.
Range is 0 to 7, where 0 is the first device.
Used only for DS0-Data Port loopback option of Latching
Loopback Type Object. No signifiance right now.rw INTEGER .1.3.6.1.4.1.321.1.3024.5001.1.17 |
ncmdsuCommonEntryAn entry in the ncmdsu information table. NcmdsuCommonEntry .ncmdsuCommonTable.1 |
ncmdsuNIDIndexro INTEGER .ncmdsuCommonTable.1.1 |
ncmdsuIndexro INTEGER .ncmdsuCommonTable.1.2 |
ncmdsuPortTypero Enumeration .ncmdsuCommonTable.1.3 |
ncmdsuPortLoopbackrw Enumeration .ncmdsuCommonTable.1.4 |
ncmdsuPortTestrw Enumeration .ncmdsuCommonTable.1.5 |
More MIBs from Verilink
Browse all VerilinkMIBs →VERILINK-ENTERPRISE-NCMGENERIC-MIB
SNMP MIB module
764 objects→
IPADv2-MIB
The IPADv2-MIB module facilitates the monitoring and management of IP Address Allocation and De-allocation (IPAD) events within network infrastructure, specifically tracking the assignment status, lease duration, and utilization of IP address pools via SNMPv2. This module enables administrators to audit dynamic address distribution, detect allocation conflicts, and verify the operational state of DHCP or IPAM services across compliant network devices.
629 objects→
VERILINK-ENTERPRISE-NCMALARM-MIB
Standard SNMP MIB module defining data structures for VERILINK-ENTERPRISE-NCMALARM-MIB.
574 objects→
DS8200v2-MIB
SNMP MIB module
446 objects→
VERILINK-ENTERPRISE-CSUNCM-MIB
SNMP MIB module
290 objects→
IPAD-MIB
Standard SNMP MIB module defining data structures for IPAD-MIB.
284 objects→