Unisphere-Data-ATM-MIB
AI MIB Summary
The Unisphere-Data-ATM-MIB enables monitoring and management of Asynchronous Transfer Mode (ATM) interface states, traffic statistics, and error counters on Unisphere Networks Inc. hardware. This module provides granular visibility into ATM-specific performance metrics, including cell loss, latency, and virtual circuit (VCC/VPC) operational status, to facilitate network troubleshooting and capacity planning.
The ATM MIB for the Unisphere Networks Inc. enterprise.
Main OID:
usdAtmMIB.1.3.6.1.4.1.4874.2.2.8
189
Objects
Active
Status
9
Dependencies
Imported Objects
Objects
189 total| Object Name |
|---|
usdAtmMIBThe ATM MIB for the Unisphere Networks Inc. enterprise. MODULE-IDENTITY .1.3.6.1.4.1.4874.2.2.8 |
usdAtmObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.8.1 |
usdAtmIfLayer OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.8.1.1 |
usdAtmNextIfIndexCoordinate ifIndex value allocation for entries in usdAtmIfTable.
A GET of this object returns the next available ifIndex value to be used
to create an entry in the associated interface table; or zero, if no
valid ifIndex value is available. This object also returns a value of
zero when it is the lexicographic successor of a varbind presented in an
SNMP GETNEXT or GETBULK request, for which circumstance it is assumed
that ifIndex allocation is unintended.
Successive GETs will typically return different values, thus avoiding
collisions among cooperating management clients seeking to create table
entries simultaneously.ro UsdNextIfIndex (Unisphere-Data-TC) .1.3.6.1.4.1.4874.2.2.8.1.1.1 |
usdAtmIfTableThis table contains entries for ATM interfaces present in the system. SEQUENCE OF UsdAtmIfEntry .1.3.6.1.4.1.4874.2.2.8.1.1.2 |
usdAtmIfEntryEach entry describes the characteristics of an ATM interface.
Creating/deleting entries in this table causes corresponding entries for
be created/deleted in ifTable/ifXTable/usdIfTable. UsdAtmIfEntry .1.3.6.1.4.1.4874.2.2.8.1.1.2.1 |
usdAtmIfIndexThe ifIndex of the ATM interface. When creating entries in this table,
suitable values for this object are determined by reading
usdAtmNextIfIndex. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.1 |
usdAtmIfRowStatusControls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy
To create an entry in this table, the following entry objects MUST be
explicitly configured:
usdAtmIfRowStatus
usdAtmIfLowerIfIndex
In addition, when creating an entry the following condition must hold:
A value for usdAtmIfIndex must have been determined previously, by
reading usdAtmNextIfIndex.
A corresponding entry in ifTable/ifXTable/usdIfTable is created or
destroyed as a result of creating/destroying an entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.2 |
usdAtmIfLowerIfIndexThe ifIndex of an interface over which this ATM interface is to be
layered. A value of zero indicates no layering. An implementation may
choose to require that a nonzero value be configured at entry creation.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.3 |
usdAtmIfIlmiVpiThe VPI of the ILMI of a major ATM interface.rw AtmVpIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.4 |
usdAtmIfIlmiVciThe VCI of the ILMI of a major ATM interface.rw AtmVcIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.5 |
usdAtmIfIlmiVcdAn integer identifier for the ILMI, used in conjunction with the
command-line interface.
The value must be unique among VCs configured on the same ATM
interface.rw Integer32 .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.6 |
usdAtmIfIlmiPollFrequencyThe amount of time in seconds between successive transmissions of ILMI
messages on this interface for the purpose of detecting loss of ILMI
connectivity. The distinguished value zero disables ILMI connectivity
procedures on this interface.rw Integer32 .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.7 |
usdAtmIfIlmiAdminStateThe administrative status of ILMI in the ATM interface.rw Enumeration .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.8 |
usdAtmIfUniVersionUse to specify the User Network Interface (UNI) the router should use
when ILMI link auto determination is unsuccesful or ILMI is disabled.rw Enumeration .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.9 |
usdAtmIfOamCellRxAdminStateUse to specify the OAM Cell Receive Administrative state on this interface.rw Enumeration .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.10 |
usdAtmIfInCellsThe total number of cells received on this major interface.ro Counter64 .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.11 |
usdAtmIfOutCellsThe total number of cells transmitted on this major interface.ro Counter64 .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.12 |
usdAtmIfVcCountThe total number of circuits configured on this interface.ro INTEGER .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.13 |
usdAtmIfMapGroupThe NBMA map group this interface is associated with.rw UsdAtmNbmaMapNameOrNull .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.14 |
usdAtmIfCacAdminStateThe administrative staus of CAC on this ATM major interface.rw UsdEnable (Unisphere-Data-TC) .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.15 |
usdAtmIfCacUbrWeightThe bandwidth associated with every UBR and UBR with PCR connection
configured on the ATM major interface. This value is used for CAC
computation. The units are kilo-bits per second (kbps).rw Integer32 .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.16 |
usdAtmIfCacSubscriptionBandwidthThe subscribed bandwidth of the ATM major interface. If this value is
not specified or set to 0, the effective port bandwidth is used. When a
Get operation is performed the current effective bandwidth is returned.
The units are kilo-bits per second (kbps).rw Integer32 .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.17 |
usdAtmIfCacAvailableBandwidthThe available bandwidth of the ATM major interface. As connections are
added or deleted on the interface, this value is updated. The units are
kilo-bits per second (kbps).ro Integer32 .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.18 |
usdAtmIfOamCellFilterThe type of OAM cells to discard when usdAtmIfOamCellRxAdminState is
set to oamCellAdminStateDisabled. The value oamCellFilterAlarm discards
received OAM AIS and RDI cells. The value oamCellFilterAll discards all
received OAM cells. Note that when usdAtmIfOamCellRxAdminState is set
to oamCellAdminStateEnabled, this object has no effect.rw Enumeration .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.23 |
usdAtmIfCacUsedBandwidthUpperThe most significant 32 bits of the CAC used bandwidth on the ATM major
interface. The least significant 32 bits of the CAC used bandwidth are
specified by usdAtmIfCacUsedBandwidthLower.ro Unsigned32 .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.24 |
usdAtmIfCacUsedBandwidthLowerThe least significant 32 bits of the CAC used bandwidth on the ATM
major interface. The most significant 32 bits of the CAC used bandwidth
are specified by usdAtmIfCacUsedBandwidthUpper.ro Unsigned32 .1.3.6.1.4.1.4874.2.2.8.1.1.2.1.25 |
usdAtmPvcStatisticsTableThis table contains statistics for PVC entries. SEQUENCE OF UsdAtmPvcStatisticsEntry .1.3.6.1.4.1.4874.2.2.8.1.1.3 |
usdAtmPvcStatisticsEntryEach entry provides statistics on an ATM PVC. UsdAtmPvcStatisticsEntry .1.3.6.1.4.1.4874.2.2.8.1.1.3.1 |
usdAtmPvcStatsIfIndexThe ifIndex of the ATM interface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.1 |
usdAtmPvcStatsVpiThe VPI of the ATM VCC used by this ATM interface and PVC. AtmVpIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.2 |
usdAtmPvcStatsVciThe VCI of the ATM VCC used by this ATM interface and PVC. AtmVcIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.3 |
usdAtmPvcStatsInCellsReceived cells.ro Counter64 .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.4 |
usdAtmPvcStatsInCellOctetsReceived cells octets.ro Counter64 .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.5 |
usdAtmPvcStatsInPacketsReceived AAL PDUs.ro Counter64 .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.6 |
usdAtmPvcStatsInPacketOctetsReceived AAL PDU octets.ro Counter64 .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.7 |
usdAtmPvcStatsOutCellsTransmitted cells.ro Counter64 .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.8 |
usdAtmPvcStatsOutCellOctetsTransmitted cell octets.ro Counter64 .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.9 |
usdAtmPvcStatsOutPacketsTransmitted AAL PDUs.ro Counter64 .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.10 |
usdAtmPvcStatsOutPacketOctetsTransmitted AAL PDU octets.ro Counter64 .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.11 |
usdAtmPvcStatsInCellErrorsReceived cells dropped due to errors.ro Counter32 .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.12 |
usdAtmPvcStatsinPacketErrorsReceived packets dropped due to errors.ro Counter32 .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.13 |
usdAtmPvcStatsOutCellErrorsCells not transmitted due to errors.ro Counter32 .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.14 |
usdAtmPvcStatsOutPacketErrorsPackets not transmitted due to errors.ro Counter32 .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.15 |
usdAtmPvcStatsInPacketDiscardsReceived packets w/o errors discarded.ro Counter32 .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.16 |
usdAtmPvcStatsInPacketOctetDiscardsReceived bytes w/o errors discarded.ro Counter32 .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.17 |
usdAtmPvcStatsInPacketUnknownProtocolReceived packets that are discarded because the interface can not discern or is not configured to support this protocol.ro Counter32 .1.3.6.1.4.1.4874.2.2.8.1.1.3.1.18 |
usdAtmVpTunnelTableThis table contains entries for ATM VP Tunnels present in the system. SEQUENCE OF UsdAtmVpTunnelEntry .1.3.6.1.4.1.4874.2.2.8.1.1.4 |
usdAtmVpTunnelEntryEach entry describes the characteristics of an ATM VP Tunnel. UsdAtmVpTunnelEntry .1.3.6.1.4.1.4874.2.2.8.1.1.4.1 |
usdAtmVpTunnelIfIndexThe ifIndex of the ATM interface. The value of this object is the same
as the usdAtmIfIndex object in the usdAtmIfTable.
Entries in this table cannot be created unless the underlying ATM
interface entry is created first in the usdAtmIfTable. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4874.2.2.8.1.1.4.1.1 |
usdAtmVpTunnelVpiThe VPI value for this VP tunnel entry. AtmVpIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4874.2.2.8.1.1.4.1.2 |
usdAtmVpTunnelKbpsThe tunnel rate in kilobits per second (kbps) for this entry.rw Integer32 .1.3.6.1.4.1.4874.2.2.8.1.1.4.1.3 |
usdAtmVpTunnelRowStatusControls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy
To create an entry in this table, the following entry objects MUST be
explicitly configured:
usdAtmVpTunnelRowStatus
usdAtmVpTunnelKbps
In addition, when creating an entry the following condition must hold:
A correponding usdAtmVpTunnelIfIndex value must have been created in
the usdAtmIfTable previously.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.1.4.1.4 |
usdAtmVpTunnelServiceCategoryThe ATM service category for the tunnel.rw Enumeration .1.3.6.1.4.1.4874.2.2.8.1.1.4.1.5 |
usdAtmIfCapabilityTableThis table contains entries for ATM interfaces present in the system. SEQUENCE OF UsdAtmIfCapabilityEntry .1.3.6.1.4.1.4874.2.2.8.1.1.5 |
usdAtmIfCapabilityEntryEach entry describes the capabilities of an ATM interface. A
management client can use this table to determine differences in the
configurable level of support across entries in this table. UsdAtmIfCapabilityEntry .1.3.6.1.4.1.4874.2.2.8.1.1.5.1 |
usdAtmIfCapabilityIndexThe ifIndex of the ATM interface. The value of this object is the same
as usdAtmIfIndex in the usdAtmIfTable. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4874.2.2.8.1.1.5.1.1 |
usdAtmIfCapabilityTrafficShapingIndicates whether traffic shaping is supported on this interface;
true(1) indicates that it is, false(2) indicates that it is not.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.1.5.1.2 |
usdAtmIfCapabilityOamIndicates whether OAM is supported on this interface; true(1) indicates
that it is, false(2) indicates that it is not.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.1.5.1.3 |
usdAtmIfCapabilityDefaultVcPerVpThe default number of VCs per VP for this interface.ro INTEGER .1.3.6.1.4.1.4874.2.2.8.1.1.5.1.4 |
usdAtmIfCapabilityNumVpiVciBitsThe total range of bits used for constructing VPI/VCI identifiers for
this interface.ro INTEGER .1.3.6.1.4.1.4874.2.2.8.1.1.5.1.5 |
usdAtmIfCapabilityMaxVcdThe maximum configurable value for a VCD on this interface.ro Integer32 .1.3.6.1.4.1.4874.2.2.8.1.1.5.1.6 |
usdAtmIfCapabilityMaxVpiThe maximum configurable value for a VPI on this interface.ro AtmVpIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4874.2.2.8.1.1.5.1.7 |
usdAtmIfCapabilityMaxVciThe maximum configurable value for a VCI on this interface.ro AtmVcIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4874.2.2.8.1.1.5.1.8 |
usdAtmIfCapabilityOamCellFilterIndicates whether OAM cell filter is supported on this interface;
true(1) indicates that it is, false(2) indicates that it is not.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.1.5.1.9 |
usdAtmIfSvcSignallingTableThis table contains entries for extending the usdAtmIfTable for
configuring signalling information for switched virtual connection
(SVC). SEQUENCE OF UsdAtmIfSvcSignallingEntry .1.3.6.1.4.1.4874.2.2.8.1.1.6 |
usdAtmIfSvcSignallingEntryEach entry provides configuration parameters for ATM signalling on the
interface. UsdAtmIfSvcSignallingEntry .1.3.6.1.4.1.4874.2.2.8.1.1.6.1 |
usdAtmIfSvcSignallingVpiThe VPI identifier of the ATM circuit used for signalling for this
interface.rw AtmVpIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4874.2.2.8.1.1.6.1.1 |
usdAtmIfSvcSignallingVciThe VCI identifier of the ATM circuit used for signalling for this
interface.rw AtmVcIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4874.2.2.8.1.1.6.1.2 |
usdAtmIfSvcSignallingVcdThe VCI identifier of the ATM circuit used for signalling for this
interface.rw AtmVcIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4874.2.2.8.1.1.6.1.3 |
usdAtmIfSvcSignallingAdminStatusThe administrative status of signalling in the ATM interface.rw AtmVorXAdminStatus (ATM-TC-MIB) .1.3.6.1.4.1.4874.2.2.8.1.1.6.1.4 |
usdAtmAal5IfLayer OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.8.1.2 |
usdAtmAal5NextIfIndexCoordinate ifIndex value allocation for entries in usdAtmAal5IfTable.
A GET of this object returns the next available ifIndex value to be used
to create an entry in the associated interface table; or zero, if no
valid ifIndex value is available. This object also returns a value of
zero when it is the lexicographic successor of a varbind presented in an
SNMP GETNEXT or GETBULK request, for which circumstance it is assumed
that ifIndex allocation is unintended.
Successive GETs will typically return different values, thus avoiding
collisions among cooperating management clients seeking to create table
entries simultaneously.ro UsdNextIfIndex (Unisphere-Data-TC) .1.3.6.1.4.1.4874.2.2.8.1.2.1 |
usdAtmAal5IfTableThis table contains entries for ATM AAL5 interfaces present in the
system. SEQUENCE OF UsdAtmAal5IfEntry .1.3.6.1.4.1.4874.2.2.8.1.2.2 |
usdAtmAal5IfEntryEach entry describes the characteristics of an ATM AAL5 interface.
Creating/deleting entries in this table causes corresponding entries for
be created/deleted in ifTable/ifXTable/usdIfTable. UsdAtmAal5IfEntry .1.3.6.1.4.1.4874.2.2.8.1.2.2.1 |
usdAtmAal5IfIndexThe ifIndex of the ATM AAL5 interface. When creating entries in this
table, suitable values for this object are determined by reading
usdAtmAal5NextIfIndex. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4874.2.2.8.1.2.2.1.1 |
usdAtmAal5IfRowStatusControls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy
To create an entry in this table, the following entry objects MUST be
explicitly configured:
usdAtmAal5IfRowStatus
usdAtmAal5IfLowerIfIndex
In addition, when creating an entry the following condition must hold:
A value for usdAtmAal5IfIndex must have been determined previously,
by reading usdAtmAal5NextIfIndex.
A corresponding entry in ifTable/ifXTable/usdIfTable is created or
destroyed as a result of creating/destroying an entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.2.2.1.2 |
usdAtmAal5IfLowerIfIndexThe ifIndex of an ATM interface over which this ATM AAL5 interface is
to be layered. A value of zero indicates no layering. An
implementation may choose to require that a nonzero value be configured
at entry creation.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.4874.2.2.8.1.2.2.1.3 |
usdAtmSubIfLayer OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.8.1.3 |
usdAtmSubIfNextIfIndexCoordinate ifIndex value allocation for entries in usdAtmSubIfTable.
A GET of this object returns the next available ifIndex value to be used
to create an entry in the associated interface table; or zero, if no
valid ifIndex value is available. This object also returns a value of
zero when it is the lexicographic successor of a varbind presented in an
SNMP GETNEXT or GETBULK request, for which circumstance it is assumed
that ifIndex allocation is unintended.
Successive GETs will typically return different values, thus avoiding
collisions among cooperating management clients seeking to create table
entries simultaneously.ro UsdNextIfIndex (Unisphere-Data-TC) .1.3.6.1.4.1.4874.2.2.8.1.3.1 |
usdAtmSubIfTableThis table contains entries for ATM Subinterfaces present in the
system. SEQUENCE OF UsdAtmSubIfEntry .1.3.6.1.4.1.4874.2.2.8.1.3.2 |
usdAtmSubIfEntryEach entry describes the characteristics of an ATM Subinterface.
Creating/deleting entries in this table causes corresponding entries for
be created/deleted in ifTable/ifXTable/usdIfTable. UsdAtmSubIfEntry .1.3.6.1.4.1.4874.2.2.8.1.3.2.1 |
usdAtmSubIfIndexThe ifIndex of the ATM Subinterface. When creating entries in this
table, suitable values for this object are determined by reading
usdAtmSubNextIfIndex. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4874.2.2.8.1.3.2.1.1 |
usdAtmSubIfRowStatusControls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy
To create an entry in this table, the following entry objects MUST be
explicitly configured:
usdAtmSubIfRowStatus
usdAtmSubIfLowerIndex
In addition, when creating an entry the following condition must hold:
A value for usdAtmSubIfIndex must have been determined previously,
by reading usdAtmSubIfNextIfIndex.
A corresponding entry in ifTable/ifXTable/usdIfTable is created or
destroyed as a result of creating/destroying an entry in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.3.2.1.2 |
usdAtmSubIfDistinguisherAn integer identifier for the subinterface, used in conjunction with
the command-line interface. It is provided here for cross-reference
purposes only.
The value must be unique among subinterfaces configured on the same
underlying ATM adaptation layer. The upper bound for the value is
further constrained to be identical with the maximum number of
subinterfaces supported by the lower interface.
If this object is not configured, a value will be allocated internally
and can be queried after table entry creation has succeeded.rw Integer32 .1.3.6.1.4.1.4874.2.2.8.1.3.2.1.3 |
usdAtmSubIfLowerIfIndexThe ifIndex of an ATM AAL5 interface over which this ATM subinterface
is to be layered. A value of zero indicates no layering. An
implementation may choose to require that a nonzero value be configured
at entry creation.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.4874.2.2.8.1.3.2.1.4 |
usdAtmSubIfNbmaThe NBMA administrative setting. Setting this value of this object to
true(1) will enable multipoint access on this interface. Setting the
value to false(2), will enable point to point access on this interface.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.3.2.1.5 |
usdAtmSubIfAddressSpecifies the local ATM NSAP address of the circuit. A GET operation
returns a full 20-octet NSAP. A SET operation only requires 7 octets,
since the prefix can be implied.rw AtmAddr .1.3.6.1.4.1.4874.2.2.8.1.3.2.1.6 |
usdAtmSubIfVccTableThis table contains entries for ATM VCCs configured on ATM
subinterfaces present in the system.
An implementation may constrain the number of VCCs permitted to be
configured per ATM Subinterface; in particular, an implementation may
restrict each ATM Subinterface to have a single VCC.
Attributes in this entry can only be configured at entry creation, and
remain fixed for the lifetime of the entry. SEQUENCE OF UsdAtmSubIfVccEntry .1.3.6.1.4.1.4874.2.2.8.1.3.3 |
usdAtmSubIfVccEntryEach entry describes the characteristics of an ATM subinterface VCC. UsdAtmSubIfVccEntry .1.3.6.1.4.1.4874.2.2.8.1.3.3.1 |
usdAtmSubIfVccVpiThe VPI of the ATM VCC used by this subinterface. AtmVpIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4874.2.2.8.1.3.3.1.1 |
usdAtmSubIfVccVciThe VCI of the ATM VCC used by this subinterface. AtmVcIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4874.2.2.8.1.3.3.1.2 |
usdAtmSubIfVccRowStatusControls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy
To create an entry in this table, the following entry objects MUST be
explicitly configured:
usdAtmSubIfVccRowStatus
In addition, when creating an entry the following conditions must hold:
The ATM Subinterface identified by usdAtmSubIfIndex must exist.
A positive value configured for usdAtmSubIfVccVcd must not already be
assigned to an existing VCC.
For each value of usdAtmSubIfVccServiceCategory, additional dependent
objects in the entry require configuration as identified here:
usdAtmSubIfVccServiceCategory Requires configuration of:
ubr <none>
ubrPcr usdAtmSubIfVccPcr
nrtVbr usdAtmSubIfVccPcr
usdAtmSubIfVccScr
usdAtmSubIfVccMbs
cbr usdAtmSubIfVccPcr
rtVbr usdAtmSubIfVccPcr
usdAtmSubIfVccScr
usdAtmSubIfVccMbs
Attributes in this entry can only be configured at entry creation,
and remain fixed for the lifetime of the entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.3.3.1.3 |
usdAtmSubIfVccVcdAn integer identifier for the circuit, used in conjunction with the
command-line interface. It is provided here for cross-reference
purposes only.
The value must be unique among VCCs configured on the same underlying
ATM interface.
If this object is not configured, or is configured with a value of zero,
a value will be allocated internally and can be queried after table
entry creation has succeeded.rw Integer32 .1.3.6.1.4.1.4874.2.2.8.1.3.3.1.4 |
usdAtmSubIfVccTypeSpecifies the encapsulation used by the circuit to carry IP datagrams.
Encapsulations are as specified in RFC1483 Multiprotocol Interconnect
over ATM. 'autoconfig' will recognize both VcMux and LLC formats.rw Enumeration .1.3.6.1.4.1.4874.2.2.8.1.3.3.1.5 |
usdAtmSubIfVccServiceCategoryService category for this circuit:
ubr Unspecified Bit Rate (best effort).
ubrPcr Unspecified Bit Rate with Peak Cell Rate limit.
nrtVbr Non-RealTime Variable Bit Rate.
cbr Constant Bit Rate.
rtVbr Realtime Variable Bit Rate.rw Enumeration .1.3.6.1.4.1.4874.2.2.8.1.3.3.1.6 |
usdAtmSubIfVccPcrPeak Cell Rate, in kilobits per second (kbps), of this circuit.
This parameter is only required when usdAtmSubIfVccServiceCategory is
configured to have one of the following values:
ubrPcr
nrtVbr
cbr
rtVbrrw Integer32 .1.3.6.1.4.1.4874.2.2.8.1.3.3.1.7 |
usdAtmSubIfVccScrSustained Cell Rate, in kilobits per second (kbps), of this circuit.
This parameter is only required when usdAtmSubIfVccServiceCategory is
configured to have the following value:
nrtVbr
rtVbrrw Integer32 .1.3.6.1.4.1.4874.2.2.8.1.3.3.1.8 |
usdAtmSubIfVccMbsMaximum Burst Size, in cells, of this circuit.
This parameter is only required when usdAtmSubIfVccServiceCategory is
configured to have the following value:
nrtVbr
rtVbrrw Integer32 .1.3.6.1.4.1.4874.2.2.8.1.3.3.1.9 |
usdAtmSubIfInverseArpEnables the inverse ARP protocol on this VCC; true(1) enables the
protocol, false(2) disables it.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.3.3.1.10 |
usdAtmSubIfInverseArpRefreshThe refresh rate in minutes between inverse ARP protocol messages.rw Integer32 .1.3.6.1.4.1.4874.2.2.8.1.3.3.1.11 |
usdAtmCircuitOamTableThis table contains circuit OAM data for a PVC. SEQUENCE OF UsdAtmCircuitOamEntry .1.3.6.1.4.1.4874.2.2.8.1.3.4 |
usdAtmCircuitOamEntryEach entry provides OAM data on an ATM PVC. UsdAtmCircuitOamEntry .1.3.6.1.4.1.4874.2.2.8.1.3.4.1 |
usdAtmCircuitOamIfIndexThe ifIndex of the ATM subinterface. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4874.2.2.8.1.3.4.1.1 |
usdAtmCircuitOamVpiThe VPI of the ATM VCC used by this ATM interface and PVC. AtmVpIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4874.2.2.8.1.3.4.1.2 |
usdAtmCircuitOamVciThe VCI of the ATM VCC used by this ATM interface and PVC. AtmVcIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4874.2.2.8.1.3.4.1.3 |
usdAtmCircuitOamAdminStatusThe administrative state of OAM for the interface identified by this
entry.rw Enumeration .1.3.6.1.4.1.4874.2.2.8.1.3.4.1.4 |
usdAtmCircuitOamLoopbackOperStatusThe operational status of OAM for the interface identified by this
entry.
oamOperStatusNotSupported(0) - OAM not supported on this interface
oamOperStatusDisabled(1) - VC integrity disabled
oamOperStatusSent(2) - Loopback sent, awaiting response
oamOperStatusReceived(3) - Loopback response received, awaiting
frequency
oamOperStatusFailed(4) - Loopback response not received, or
invalid response receivedro Enumeration .1.3.6.1.4.1.4874.2.2.8.1.3.4.1.5 |
usdAtmCircuitVcOamOperStatusThe OAM VC operational status of this entry.
oamVcOperStateAisState(0) - AIS cell received or underlying
physical layer reporting transmission
path AIS
oamVcOperStateRdiState(1) - RDI cell received
oamVcOperStateDownRetry(2) - OAM loopback failed, using retry
frequency to verify that the VC is
really down
oamVcOperStateUpRetry(3) - OAM loopback successful, using retry
frequency to verify that the VC is
really up
oamVcOperStateUp(4) - OAM loopback successful after up retry
verification
oamVcOperStateDown(5) - OAM loopback failed after down retry
verification
oamVcOperStateNotManaged(6)- No verification via loopback cells
being performed.ro Enumeration .1.3.6.1.4.1.4874.2.2.8.1.3.4.1.6 |
usdAtmCircuitOamLoopbackFrequencyThe OAM loopback frequency for the interface identified by this entry.rw Integer32 .1.3.6.1.4.1.4874.2.2.8.1.3.4.1.7 |
usdAtmCircuitInOamF5CellsReceived OAM F5 cells.ro Counter32 UNITS "cells" .1.3.6.1.4.1.4874.2.2.8.1.3.4.1.8 |
usdAtmCircuitInOamCellsDroppedReceived OAM cells that were dropped.ro Counter32 UNITS "cells" .1.3.6.1.4.1.4874.2.2.8.1.3.4.1.9 |
usdAtmCircuitOutOamF5CellsTransmitted OAM F5 cells.ro Counter32 UNITS "cells" .1.3.6.1.4.1.4874.2.2.8.1.3.4.1.10 |
usdAtmCircuitInOamF5EndToEndLoopbackCellsReceived OAM F5 end-to-end loopback cells.ro Counter32 UNITS "cells" .1.3.6.1.4.1.4874.2.2.8.1.3.4.1.11 |
usdAtmCircuitInOamF5SegmentLoopbackCellsReceived OAM F5 segment loopback cells.ro Counter32 UNITS "cells" .1.3.6.1.4.1.4874.2.2.8.1.3.4.1.12 |
usdAtmCircuitInOamF5AisCellsReceived OAM F5 AIS cells.ro Counter32 UNITS "cells" .1.3.6.1.4.1.4874.2.2.8.1.3.4.1.13 |
usdAtmCircuitInOamF5RdiCellsReceived OAM F5 RDI cells.ro Counter32 UNITS "cells" .1.3.6.1.4.1.4874.2.2.8.1.3.4.1.14 |
usdAtmCircuitOutOamF5EndToEndLoopbackCellsTransmitted OAM F5 end-to-end loopback cells.ro Counter32 UNITS "cells" .1.3.6.1.4.1.4874.2.2.8.1.3.4.1.15 |
usdAtmCircuitOutOamF5SegmentLoopbackCellsTransmitted OAM F5 segment loopback cells.ro Counter32 UNITS "cells" .1.3.6.1.4.1.4874.2.2.8.1.3.4.1.16 |
usdAtmCircuitOutOamF5RdiCellsTransmitted OAM F5 RDI cells.ro Counter32 UNITS "cells" .1.3.6.1.4.1.4874.2.2.8.1.3.4.1.17 |
usdAtmSubIfVccTrafficShapingTableThis table contains entries for traffic shaping of ATM VCCs configured
on ATM subinterfaces present in the system. This table augments the
usdAtmSubIfVccTable only for VCCs that support traffic shapping.
Attributes in this entry can only be configured at entry creation, and
remain fixed for the lifetime of the entry. SEQUENCE OF UsdAtmSubIfVccTrafficShapingEntry .1.3.6.1.4.1.4874.2.2.8.1.3.5 |
usdAtmSubIfVccTrafficShapingEntryEach entry describes the traffic shping characteristics of an ATM
subinterface VCC. UsdAtmSubIfVccTrafficShapingEntry .1.3.6.1.4.1.4874.2.2.8.1.3.5.1 |
usdAtmSubIfVccTrafficShapingCdvtThe network cell delay variation tolerance (CDVT) in tenths of a
microsecond.rw Unsigned32 UNITS "tenths of a microsecond" .1.3.6.1.4.1.4874.2.2.8.1.3.5.1.1 |
usdAtmSubIfVccTrafficShapingClp0Specifies whether or not only CLP0 cells are to be policed according to
the traffic contract. CLP1 cells are forwarded on a best-effort basis
CLP-significant model for (VBR.2, VBR.3 conformance). Applicable only
for VBR circuits.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.3.5.1.2 |
usdAtmSubIfVccTrafficShapingTaggingSpecifies whether or not CLP0 cells should be tagged for SCR policing
(VBR.3 conformance). Applicable only for VBR circuits.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.3.5.1.3 |
usdAtmSubIfVccTrafficShapingPoliceObserveSpecifies whether of not no policing action is to be taken (note the
double negative; if true(1) then no policing action will be taken; if
false(2) then policing action will be taken). Regardless of the state
of this object, all counters will be incremented.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.3.5.1.4 |
usdAtmSubIfVccTrafficShapingPacketShapingSpecifies whether of not to shape output traffic on a packet boundary.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.3.5.1.5 |
usdAtmSubIfSvcConfigTableThis table contains entries for extending the usdAtmSubIfTable to
configure switched virtual connection (SVC)on the subinterfaces. SEQUENCE OF UsdAtmSubIfSvcConfigEntry .1.3.6.1.4.1.4874.2.2.8.1.3.6 |
usdAtmSubIfSvcConfigEntryEach entry provides configuration parameters for an ATM SVC
on the subinterface. UsdAtmSubIfSvcConfigEntry .1.3.6.1.4.1.4874.2.2.8.1.3.6.1 |
usdAtmSubIfSvcRowStatusControls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.3.6.1.1 |
usdAtmSubIfSvcConfigDestAtmAddressSpecifies the destination ATM NSAP address of the circuit.rw AtmAddr .1.3.6.1.4.1.4874.2.2.8.1.3.6.1.2 |
usdAtmSubIfSvcConfigCircuitTypeSpecifies the encapsulation used by the circuit to carry IP datagrams.
Encapsulations are as specified in RFC1483 Multiprotocol Interconnect
over ATM.rw Enumeration .1.3.6.1.4.1.4874.2.2.8.1.3.6.1.3 |
usdAtmSubIfSvcConfigServiceCategoryService category for this circuit:
ubr Unspecified Bit Rate (best effort).
ubrPcr Unspecified Bit Rate with Peak Cell Rate limit.
nrtVbr Non-RealTime Variable Bit Rate.
cbr Constant Bit Rate.
rtVbr Realtime Variable Bit Rate.rw Enumeration .1.3.6.1.4.1.4874.2.2.8.1.3.6.1.4 |
usdAtmSubIfSvcConfigPcrPeak Cell Rate, in kilo-bits per second (kbps), of this circuit.rw Unsigned32 UNITS "kbps" .1.3.6.1.4.1.4874.2.2.8.1.3.6.1.5 |
usdAtmSubIfSvcConfigScrSustained Cell Rate, in kilo-bits per second (kbps), of this circuit.rw Unsigned32 UNITS "kbps" .1.3.6.1.4.1.4874.2.2.8.1.3.6.1.6 |
usdAtmSubIfSvcConfigMbsMaximum Burst Size, in cells, of this circuit.rw Unsigned32 UNITS "cells" .1.3.6.1.4.1.4874.2.2.8.1.3.6.1.7 |
usdAtmSubIfSvcConfigCdvtSpecify the network Cell Delay Variation Tolerance.rw Unsigned32 UNITS "100us" .1.3.6.1.4.1.4874.2.2.8.1.3.6.1.8 |
usdAtmSubIfSvcConfigClp0Specify that only CLP0 cells are to be policed according to the traffic
contract. CLP1 cells are forwarded on a best-effort basis
CLP-significant model for (VBR.2, VBR.3 conformance).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.3.6.1.9 |
usdAtmSubIfSvcConfigTaggingSpecify that CLP0 cells should be tagged for SCR policing (VBR.3
conformance).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.3.6.1.10 |
usdAtmSubIfSvcConfigObserveSpecify that no policing action is to be taken; only counters are
incremented.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.3.6.1.11 |
usdAtmSubIfSvcConfigPacketDiscardEnable early packet Discard for this circuit.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.3.6.1.12 |
usdAtmNbma OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.8.1.4 |
usdAtmNbmaMapTableThis table contains entries for ATM NBMA maps. SEQUENCE OF UsdAtmNbmaMapEntry .1.3.6.1.4.1.4874.2.2.8.1.4.1 |
usdAtmNbmaMapEntryEach entry describes the characteristics of an ATM NBMA map. UsdAtmNbmaMapEntry .1.3.6.1.4.1.4874.2.2.8.1.4.1.1 |
usdAtmNbmaMapNameThe NBMA map name. UsdAtmNbmaMapName .1.3.6.1.4.1.4874.2.2.8.1.4.1.1.1 |
usdAtmNbmaMapVcdAn integer identifier for the ATM circuit, used in conjunction with the
command-line interface.
The value must be unique among VCs configured on the same ATM
interface. Integer32 .1.3.6.1.4.1.4874.2.2.8.1.4.1.1.2 |
usdAtmNbmaMapIpAddressThe IP address associated with this entry.rw IpAddress .1.3.6.1.4.1.4874.2.2.8.1.4.1.1.3 |
usdAtmNbmaMapVpiThe VPI identifier of the ATM circuit.ro AtmVpIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4874.2.2.8.1.4.1.1.4 |
usdAtmNbmaMapVciThe VCI identifier of the ATM circuit.ro AtmVcIdentifier (ATM-TC-MIB) .1.3.6.1.4.1.4874.2.2.8.1.4.1.1.5 |
usdAtmNbmaMapIfIndexThe ifIndex of the ATM major interface associated with this entry.
The value of this object will be zero when the map is not applied
to an interface.ro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.4874.2.2.8.1.4.1.1.6 |
usdAtmNbmaMapBroadcastThe broadcast enable/disable setting for this entry. The value true(1)
enable broadcast support; disable(2) disabled broadcast support for this
entry.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.4.1.1.7 |
usdAtmNbmaMapRowStatusControls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy
Additional notes to aid the network manager:
- NBMA maps are not supported on dynamic interface.
- NBMA maps can only be applied to a single major ATM interface at a
time.
- NBMA maps cannot be deleted unless the map is removed from the ATM
interface (usdAtmNbmaMapIfIndex = 0).
- The values of usdAtmNbmaMapVpi, usdAtmNbmaMapVci and
usdAtmNbmaMapIfIndex are zero until the map is applied to a major ATM
interface.
- To create an entry in this table, the following objects must be
present in the set PDU:
usdAtmNbmaMapIpAddress
usdAtmNbmaMapBroadcast
usdAtmNbmaMapRowStatus
- Once created, only the following objects can be modified:
usdAtmNbmaMapBroadcastrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.4.1.1.8 |
usdAtmNbmaMapListTableThis table contains entries for ATM NBMA map lists. SEQUENCE OF UsdAtmNbmaMapListEntry .1.3.6.1.4.1.4874.2.2.8.1.4.2 |
usdAtmNbmaMapListEntryEach entry describes the characteristics of an ATM NBMA map. UsdAtmNbmaMapListEntry .1.3.6.1.4.1.4874.2.2.8.1.4.2.1 |
usdAtmNbmaMapListNameThe NBMA Map List name. UsdAtmNbmaMapName .1.3.6.1.4.1.4874.2.2.8.1.4.2.1.1 |
usdAtmNbmaMapListRowStatusControls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.4.2.1.2 |
usdAtmPing OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.8.1.5 |
usdAtmPingTestTypes OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.8.1.5.1 |
usdAtmPingTestOamSegThis identifies an OAM Ping (multiple loopbacks) Test on a VPL, VPC,
VCL, or VCC termination point, using segment OAM cells.
The test type must have appended to it a code that uniquely identifies
an intermediate point responsible for looping back each cell. If this
is absent, the loopbacks are performed at the end of the segment or
connection.
E.g., the OID { usdAtmPingTestOamSeg 5 } identifies that the loopbacks
should be performed at the intermediate point labeled 5. OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.8.1.5.1.1 |
usdAtmPingTestOamE2EThis identifies an OAM Ping (multiple loopbacks) Test on a VPL, VPC,
VCL, or VCC termination point, using end-to-end OAM cells. OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.8.1.5.1.2 |
usdAtmVpPingTableThis table contains entries for extending the ATM-FORUM-SNMP-M4-MIB
atmM4VpTestTable to do ping (multiple loopback) type testing. SEQUENCE OF UsdAtmVpPingEntry .1.3.6.1.4.1.4874.2.2.8.1.5.2 |
usdAtmVpPingEntryEach entry describes the characteristics, status and results of the
most recent ATM ping test. UsdAtmVpPingEntry .1.3.6.1.4.1.4874.2.2.8.1.5.2.1 |
usdAtmVpPingProbeCountThe number of ping probes (OAM cells) to be sent to complete the test.rw Unsigned32 .1.3.6.1.4.1.4874.2.2.8.1.5.2.1.1 |
usdAtmVpPingTimeOutSpecifies the time-out value, in seconds, for a remote ping operation.rw Unsigned32 .1.3.6.1.4.1.4874.2.2.8.1.5.2.1.2 |
usdAtmVpPingCtlTrapGenerationThe value of this object determines when and if to generate a
notification for this entry:
testCompletion(0) - Generate a usdPingTestCompleted notification.
The value of this object defaults to zero, indicating that no
notification has been selected.rw Bits .1.3.6.1.4.1.4874.2.2.8.1.5.2.1.3 |
usdAtmVpPingSentProbesThe number of ping probes (OAM cells) that have been sent thus far for
this test. The value of this object MUST be set to zero when the
atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1).ro Unsigned32 UNITS "probes" .1.3.6.1.4.1.4874.2.2.8.1.5.2.1.4 |
usdAtmVpPingProbeResponsesThe number of ping responses that have been received thus far for this
test. The value of this object MUST be set to zero when the
atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1).ro Unsigned32 UNITS "probes" .1.3.6.1.4.1.4874.2.2.8.1.5.2.1.5 |
usdAtmVpPingStartTimeThe time (sysUpTime) when the test started.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.5.2.1.6 |
usdAtmVpPingMinRttThe shortest round-trip-time (RTT) for the pings that have received
responses. The value of this object MUST be set to zero when the
atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1). A
value of zero for this object implies that no ping responses have been
received for the current test.ro Unsigned32 UNITS "milliseconds" .1.3.6.1.4.1.4874.2.2.8.1.5.2.1.7 |
usdAtmVpPingMaxRttThe longest round-trip-time (RTT) for the pings that have received
responses. The value of this object MUST be set to zero when the
atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1). A
value of zero for this object implies that no ping responses have been
received for the current test.ro Unsigned32 UNITS "milliseconds" .1.3.6.1.4.1.4874.2.2.8.1.5.2.1.8 |
usdAtmVpPingAverageRttThe average round-trip-time (RTT) for all the pings that have received
responses. The value of this object MUST be set to zero when the
atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1). A
value of zero for this object implies that no ping responses have been
received for the current test.ro Unsigned32 UNITS "milliseconds" .1.3.6.1.4.1.4874.2.2.8.1.5.2.1.9 |
usdAtmVcPingTableThis table contains entries for extending the ATM-FORUM-SNMP-M4-MIB
atmM4VcTestTable to do ping (multiple loopback) type testing. SEQUENCE OF UsdAtmVcPingEntry .1.3.6.1.4.1.4874.2.2.8.1.5.3 |
usdAtmVcPingEntryEach entry describes the characteristics, status and results of the
most recent ATM ping test. UsdAtmVcPingEntry .1.3.6.1.4.1.4874.2.2.8.1.5.3.1 |
usdAtmVcPingProbeCountThe number of ping probes (OAM cells) to be sent to complete the test.rw Unsigned32 .1.3.6.1.4.1.4874.2.2.8.1.5.3.1.1 |
usdAtmVcPingTimeOutSpecifies the time-out value, in seconds, for a remote ping operation.rw Unsigned32 .1.3.6.1.4.1.4874.2.2.8.1.5.3.1.2 |
usdAtmVcPingCtlTrapGenerationThe value of this object determines when and if to generate a
notification for this entry:
testCompletion(0) - Generate a usdPingTestCompleted notification.
The value of this object defaults to zero, indicating that no
notification has been selected.rw Bits .1.3.6.1.4.1.4874.2.2.8.1.5.3.1.3 |
usdAtmVcPingSentProbesThe number of ping probes (OAM cells) that have been sent thus far for
this test. The value of this object MUST be set to zero when the
atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1).ro Unsigned32 UNITS "probes" .1.3.6.1.4.1.4874.2.2.8.1.5.3.1.4 |
usdAtmVcPingProbeResponsesThe number of ping responses that have been received thus far for this
test. The value of this object MUST be set to zero when the
atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1).ro Unsigned32 UNITS "probes" .1.3.6.1.4.1.4874.2.2.8.1.5.3.1.5 |
usdAtmVcPingStartTimeThe time (sysUpTime) when the test started.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.4874.2.2.8.1.5.3.1.6 |
usdAtmVcPingMinRttThe shortest round-trip-time (RTT) for the pings that have received
responses. The value of this object MUST be set to zero when the
atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1). A
value of zero for this object implies that no ping responses have been
received for the current test.ro Unsigned32 UNITS "milliseconds" .1.3.6.1.4.1.4874.2.2.8.1.5.3.1.7 |
usdAtmVcPingMaxRttThe longest round-trip-time (RTT) for the pings that have received
responses. The value of this object MUST be set to zero when the
atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1). A
value of zero for this object implies that no ping responses have been
received for the current test.ro Unsigned32 UNITS "milliseconds" .1.3.6.1.4.1.4874.2.2.8.1.5.3.1.8 |
usdAtmVcPingAverageRttThe average round-trip-time (RTT) for all the pings that have received
responses. The value of this object MUST be set to zero when the
atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1). A
value of zero for this object implies that no ping responses have been
received for the current test.ro Unsigned32 UNITS "milliseconds" .1.3.6.1.4.1.4874.2.2.8.1.5.3.1.9 |
usdAtmTraps OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.8.3 |
usdAtmTrapPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.8.3.0 |
usdAtmVpPingTestCompletedGenerated at the completion of a AtmfM4VpTest when the corresponding
usdAtmVpPingCtlTrapGeneration object has the testCompletion(0) bit set. NOTIFICATION-TYPE .1.3.6.1.4.1.4874.2.2.8.3.0.1 |
usdAtmVcPingTestCompletedGenerated at the completion of a AtmfM4VcTest when the corresponding
usdAtmVcPingCtlTrapGeneration object has the testCompletion(0) bit set. NOTIFICATION-TYPE .1.3.6.1.4.1.4874.2.2.8.3.0.2 |
usdAtmConformance OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.8.4 |
usdAtmCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.8.4.1 |
usdAtmGroups OBJECT IDENTIFIER .1.3.6.1.4.1.4874.2.2.8.4.2 |