UDS1-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
108
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
108 total| Object Name |
|---|
usr OBJECT IDENTIFIER .1.3.6.1.4.1.429 |
RFC1213-MIB Unknown .1.3.6.1.4.1.429 |
nas OBJECT IDENTIFIER .1.3.6.1.4.1.429.1 |
uds1 OBJECT IDENTIFIER .1.3.6.1.4.1.429.1.4 |
uds1ConfigTableThis table is an extension of the ds1ConfigTable in the DS1
MIB defined by RFC1232. SEQUENCE OF Uds1ConfigEntry .1.3.6.1.4.1.429.1.4.1 |
uds1ConfigEntryThis table contains configurable parameters for a CSU that
are not supported in the DS1 MIB defined by RFC1232. Each
entry in this table corresponds to an entry in the DS1 MIB.
There is a one-to-one correspondance between the value of
uds1CSUIndex and ds1CSUIndex. Uds1ConfigEntry .1.3.6.1.4.1.429.1.4.1.1 |
uds1CfgIndexThe index value which uniquely identifies the CSU to which
this entry is applicable. The value corresponds to
ds1CSUIndex in the DS1 MIB defined in RFC1232. The value
of uds1CfgIndex matches the value of the index for the
corresponding DS1 entity in the entity table of the chassis
MIB.ro INTEGER .1.3.6.1.4.1.429.1.4.1.1.1 |
uds1CfgRespToRemoteLoopbkThis object configures the specified CSU to either ignore
or respond to remotely initiated loopback requests.rw Enumeration .1.3.6.1.4.1.429.1.4.1.1.2 |
uds1CfgJitterAttenuationThis object is used to select how the jitter attenuation
circuit on the CSU is to be used. It can be used to
attenuate jitter on the receiver, or the transmitter.rw Enumeration .1.3.6.1.4.1.429.1.4.1.1.3 |
uds1CfgXmitLineBuildOutThis object is used to configure the amount of attenuation
that is to be applied to the transmit signal in order to
control cross-talk, etc.rw Enumeration .1.3.6.1.4.1.429.1.4.1.1.4 |
uds1CfgAutoBusyEnableThis object is used to enable or disable the automatic busy
out feature for all timeslots on the specified CSU. If
enabled, when a modem is considered idle and that modem is
not sending the idle pattern to the T1 Card on the TDM bus,
the timeslot will be busied out.rw Enumeration .1.3.6.1.4.1.429.1.4.1.1.5 |
uds1CfgDialInAdrThis object identifies whether or not DNIS digits will be
transferred as part of the call setup for the specified T1
line.rw Enumeration .1.3.6.1.4.1.429.1.4.1.1.6 |
uds1CfgZeroCodingThis object defines the type of zero coding used on the
specified DS1. It provides some values that are not
present in the experimental DS1 MIB.rw Enumeration .1.3.6.1.4.1.429.1.4.1.1.7 |
uds1CfgDialInOutTrunkStThis will set the Dial-in/Dial-out trunk start signal type.
Default = wink(1).rw Enumeration .1.3.6.1.4.1.429.1.4.1.1.8 |
uds1CfgDialInAdrAckWinkEnAllows to enable/disable an acknowledgement wink after the
dial-in address information has been received.rw Enumeration .1.3.6.1.4.1.429.1.4.1.1.9 |
uds1CfgDialOutAdrDlyAllows an adjustable delay on sending out address
information from the T1 NAC to the TELCO.rw INTEGER .1.3.6.1.4.1.429.1.4.1.1.10 |
uds1CfgStuffByteValueThe stuffed byte to send to TELCO for inactive DS0 in
Fractional T1.rw INTEGER .1.3.6.1.4.1.429.1.4.1.1.11 |
uds1CfgDialInOutTrunkTypeThis will set the Dial-In/Dial-out trunk type. Default =
eAndMTypeII(1).rw Enumeration .1.3.6.1.4.1.429.1.4.1.1.12 |
uds1CfgPriSwitchTypeThis sets the primary switch type for the T1-PRI ISDN NAC.
The setting takes effect at NAC boot time.
Default =
priSw5ESS(2).rw Enumeration .1.3.6.1.4.1.429.1.4.1.1.13 |
uds1CfgIdleByteThis sets the idle byte pattern for the T1-PRI ISDN NAC.
The setting takes effect at NAC boot time.
Default = 0xFE.rw INTEGER .1.3.6.1.4.1.429.1.4.1.1.14 |
uds1CfgAnlgBlockErrCodeThis is the error code that will be returned to an ISDN
switch when analog connections are being blocked.
Default =
58.rw INTEGER .1.3.6.1.4.1.429.1.4.1.1.15 |
uds1CfgDgtlBlockErrCodeThis is the error code that will be returned to an ISDN
switch when digital connections are being blocked.
Default
= 58.rw INTEGER .1.3.6.1.4.1.429.1.4.1.1.16 |
uds1CfgNoMdmAvailErrCodeThis is the error code that will be returned to an ISDN
switch when there are no modems available to accept the
requested connection.
Default = 58.rw INTEGER .1.3.6.1.4.1.429.1.4.1.1.17 |
uds1CfgNoIgwsAvailErrCodeThis is the error code that will be returned to an ISDN
switch when no IGWS connections are available.
Default =
58.rw INTEGER .1.3.6.1.4.1.429.1.4.1.1.18 |
uds1CfgChanBlockErrCodeThis is the error code that will be returned to an ISDN
switch when connections to a specific B channel are being
blocked.
Default = 58.rw INTEGER .1.3.6.1.4.1.429.1.4.1.1.19 |
uds1CfgBlockCallTypeThis object determines if a PRI span line will block calls
of a specific type. This object does not apply to a NAC
operating in Rob Bit T1 mode.
Default = blockNone(2).rw Enumeration .1.3.6.1.4.1.429.1.4.1.1.20 |
uds1CfgNfasIdThis defines the NFAS ID associated with a PRI span line.
This object does not apply to Rob Bit T1 operation.
Default
= 0.rw INTEGER .1.3.6.1.4.1.429.1.4.1.1.21 |
uds1CfgNfasDChannelThis determines how a PRI span line will use the DS0
normally assigned as a D channel when NFAS is being used.
This object does not apply to Rob Bit T1 operation.
Default
= dchannel(2).rw Enumeration .1.3.6.1.4.1.429.1.4.1.1.22 |
uds1CfgShrtHaulDistVariuos distance ranges supported by Short Haul NIC
Default=len0thru133Ft.rw Enumeration .1.3.6.1.4.1.429.1.4.1.1.23 |
uds1CfgCallProceedingRspThis object determines to send CALL_PROCEEDING and CONNECT
response, when a SETUP message is received from
TELCO.
Default = ON.rw Enumeration .1.3.6.1.4.1.429.1.4.1.1.24 |
uds1CfgAlertingRspThis object determines to send ALERTING response, when a
SETUP message is received from TELCO.
Default = OFF.rw Enumeration .1.3.6.1.4.1.429.1.4.1.1.25 |
uds1CfgServiceStateThis objects configures the service state of the DS1 and
will configure the state for power up if saved to NVRAM.
Default= inService(2).rw Enumeration .1.3.6.1.4.1.429.1.4.1.1.26 |
uds1CfgIcbKeywordThis is the keyword used for DASS2 Incoming Call Barring
control.rw DisplayString .1.3.6.1.4.1.429.1.4.1.1.27 |
uds1CfgOverlapRxModeThis object allows dialed digits to arrive in separate
messages. Default = disabled(2)rw Enumeration .1.3.6.1.4.1.429.1.4.1.1.28 |
uds1CfgEandMnoAddrTimerThis object is for E&M type II trunks with no DNIS address.
If timer is >0, the ch T1 NAC will flush calls upon timer
expiration, if the modem has not signalled the NAC to go
ahead and answer the call. 2 seconds per unit. Default = 0rw INTEGER .1.3.6.1.4.1.429.1.4.1.1.29 |
uds1CfgSeizureWinkDlyAllows an adjustable delay on sending out address
information from the T1 NAC to the TELCO. Default=18.rw INTEGER .1.3.6.1.4.1.429.1.4.1.1.30 |
uds1IntervalTableAn extension of the DS1 Interval table which provides
status counters over 15 minute intervals. SEQUENCE OF Uds1IntervalEntry .1.3.6.1.4.1.429.1.4.2 |
uds1IntervalEntryAn entry in the extended DS1 Interval table. Every entry
in the DS1 Interval table will have a corresponding entry
in this table. Uds1IntervalEntry .1.3.6.1.4.1.429.1.4.2.1 |
uds1IntIndexThis is the index value which uniquely identifies the CSU
to which this entry is applicable. The value of
uds1IntIndex matches the value of the index for the
corresponding DS1 entity in the entity table of the chassis
MIB.ro INTEGER .1.3.6.1.4.1.429.1.4.2.1.1 |
uds1IntNumberA number between 1 and 96, where 1 is the most recently
completed 15 minute interval and 96 is the least recently
completed 15 minute interval (assuming that all 96
intervals are valid).ro INTEGER .1.3.6.1.4.1.429.1.4.2.1.2 |
uds1IntBurstyErrSecondsThis object counts the number of seconds, over the
specified interval, in which there were more than 2 and
less than 320 CRC errors.ro Counter .1.3.6.1.4.1.429.1.4.2.1.3 |
uds1IntFrameBitErrorsA specific bit pattern is used for the T1 receiver to
determine frame allignment. This object counts the number
of incorrectly received framing bits in the specified 15
minute interval.ro Counter .1.3.6.1.4.1.429.1.4.2.1.4 |
uds1IntDeltaFrameAllignsThis object counts the number of times the specified T1
receiver has reframed on a new framing pattern (ie. due to
an OOF condition) in the specified 15 minute interval.ro Counter .1.3.6.1.4.1.429.1.4.2.1.5 |
uds1IntExcessCRCErrorsThis object counts each time 32 of any 33 consecutive CRCs
are in error for the specified T1 line in the specified 15
minute interval. This counter is only valid in ESF format.ro Counter .1.3.6.1.4.1.429.1.4.2.1.6 |
uds1CurrentTableAn extension of the DS1 Current table that provides status
counters over the present 15 minute interval. SEQUENCE OF Uds1CurrentEntry .1.3.6.1.4.1.429.1.4.3 |
uds1CurrentEntryAn entry in the extended DS1 Current table. Every entry in
the DS1 Current table will have a corresponding entry in
this table. Uds1CurrentEntry .1.3.6.1.4.1.429.1.4.3.1 |
uds1CurrIndexThe index value which uniquely identifies the CSU to which
this entry is applicable. The value of uds1CurrIndex
matches the value of the index for the corresponding DS1
entity in the entity table of the chassis MIB.ro INTEGER .1.3.6.1.4.1.429.1.4.3.1.1 |
uds1CurrBurstyErrSecondsThis object counts the number of seconds, in the current 15
minute interval, during which there was more than two, and
less than 320 CRC errors.ro Counter .1.3.6.1.4.1.429.1.4.3.1.2 |
uds1CurrFrameBitErrorsA specific bit pattern is used for the receiver to
determine frame allignment. This object is a count of the
number of incorrectly received framing bits in the current
15 minute interval.ro Counter .1.3.6.1.4.1.429.1.4.3.1.3 |
uds1CurrDeltaFrameAllignsThis object counts the number of times the specified T1
receiver has reframed on a new framing pattern (ie. due to
an OOF condition) in the current 15 minute interval.ro Counter .1.3.6.1.4.1.429.1.4.3.1.4 |
uds1CurrExcessCRCErrorsThis object counts each time 32 of any 33 consecutive CRCs
are in error for the specified T1 line in the current 15
minute interval. This counter is only valid in ESF format.ro Counter .1.3.6.1.4.1.429.1.4.3.1.5 |
uds1TotalTableAn extension of the DS1 Total table that provides the
cumulative sum of the various statistics for the 24 hour
interval preceding the first valid interval in the
uds1CurrentTable. SEQUENCE OF Uds1TotalEntry .1.3.6.1.4.1.429.1.4.4 |
uds1TotalEntryAn entry in the extended DS1 Total table. Uds1TotalEntry .1.3.6.1.4.1.429.1.4.4.1 |
uds1TotIndexThe index value which uniquely identifies the CSU to which
this entry is applicable. The value of ds1TotalIndex
matches the value of the index for the corresponding DS1
entity in the entity table of the chassis MIB.ro INTEGER .1.3.6.1.4.1.429.1.4.4.1.1 |
uds1TotBurstyErrSecondsThis object counts the number of seconds, over the last 24
hour period, in which there were more than 2 and less than
320 CRC errors.ro Counter .1.3.6.1.4.1.429.1.4.4.1.2 |
uds1TotFrameBitErrorsA specific bit pattern is used so the T1 receiver can
determine frame allignment. This object counts the total
number of incorrectly received framing bits in the last 24
hour period.ro Counter .1.3.6.1.4.1.429.1.4.4.1.3 |
uds1TotDeltaFrameAllignsThis object counts the number of times the specified T1
receiver has reframed on a new framing pattern (ie. due to
an OOF condition) in the last 24 hour period.ro Counter .1.3.6.1.4.1.429.1.4.4.1.4 |
uds1TotExcessCRCErrorsThis object indicates the total number of times there have
been 32 of any 33 consecutive CRCs in error on the
specified T1 line in the last 24 hour period. This counter
is only valid in ESF format.ro Counter .1.3.6.1.4.1.429.1.4.4.1.5 |
uds1StatTableUSR's DS1 Status table contains various CSU status
information. There is no corresponding table in the DS1
MIB defined by RFC1232. SEQUENCE OF Uds1StatEntry .1.3.6.1.4.1.429.1.4.5 |
uds1StatEntryThere is one entry in the DS1 Status table for each CSU in
the chassis. Uds1StatEntry .1.3.6.1.4.1.429.1.4.5.1 |
uds1StatIndexThe index value which uniquely identifies the CSU to which
this entry is applicable. The value of this object matches
the value of the index for the corresponding DS1 entity in
the entity table of the chassis MIB.ro INTEGER .1.3.6.1.4.1.429.1.4.5.1.1 |
uds1StatReceiverGainThis object identifies the amount of gain applied to boost
the receive signal level to an appropriate operating level.ro Enumeration .1.3.6.1.4.1.429.1.4.5.1.2 |
uds1StatOutOfFrameThis object indicates when the framing pattern for the
specified T1 line has been lost and data connot be
extracted properly. This condition is also known as red
alarm.ro Enumeration .1.3.6.1.4.1.429.1.4.5.1.3 |
uds1StatLossOfSignalThis object indicates when 175 consecutive 0's have been
detected. The signal is considered recovered if the 1's
density reaches 12.5% (ie. four ones in a 32 bit period).ro Enumeration .1.3.6.1.4.1.429.1.4.5.1.4 |
uds1StatReceivingAISThis object identifies when the remote end of the specified
T1 line has lost its receive signal and is transmitting a
stream of all 1's to the local end. This AIS condition is
also known as blue alarm.ro Enumeration .1.3.6.1.4.1.429.1.4.5.1.5 |
uds1StatSwitchTypeActiveThis object identifies the primary switch type that the
T1-PRI ISDN NAC is currently connected to.ro Enumeration .1.3.6.1.4.1.429.1.4.5.1.6 |
uds1StatDchanOperationalThis object reflects the operational status of the D
channel on the T1-PRI ISDN NAC.ro Enumeration .1.3.6.1.4.1.429.1.4.5.1.7 |
uds1StatE1ContCrcThis object indicates when continuous CRC errors are being
received on the E1 DS1 span line on the T1-PRI ISDN NAC.ro Enumeration .1.3.6.1.4.1.429.1.4.5.1.8 |
uds1StatE1PhysicalStateThis object reflects the physical state of the E1 DS1 span
line on the T1-PRI ISDN NAC.ro Enumeration .1.3.6.1.4.1.429.1.4.5.1.9 |
uds1StatLoopBackInitThis object tells if the loopback was initiated by the
network or by commandro Enumeration .1.3.6.1.4.1.429.1.4.5.1.10 |
uds1StatNfasDChannelThis reflect how a PRI span line is using the DS0 normally
assigned as a D channel when NFAS is being used. This
object does not apply to Rob Bit T1 operation.
Default =
dchannel(2).ro Enumeration .1.3.6.1.4.1.429.1.4.5.1.11 |
uds1StatDChannelThis is the status of the D channel for this PRI span line.
A value of notSupported(1) means that this DS1 is not
operating in ISDN mode or there is no D channel defined on
this span line.ro Enumeration .1.3.6.1.4.1.429.1.4.5.1.12 |
uds1StatDs0SrvcChngLstThis object contains the current list of DS0s that have
changed their state from In Service to Out of Service or
Vice versa. The list is included in the corresponding SNMP
trap.ro DisplayString .1.3.6.1.4.1.429.1.4.5.1.13 |
uds1StatMultiFrameThis object identifies when the E1/PRI NAC line has lost
synchronization with the Time-Slot 16 Multi-Frame alignment
pattern. Only valid for E1/CAS NAC.ro Enumeration .1.3.6.1.4.1.429.1.4.5.1.14 |
uds1StatRemMultiFrameThis object identifies when the remote end of the specified
E1/PRI NAC line has lost synchronization with the Time-Slot
16 Multi-Frame alignment pattern. Only valid for E1/CAS
NAC.ro Enumeration .1.3.6.1.4.1.429.1.4.5.1.15 |
uds1StatServiceStateThis object shows the current state of the DS1 Service.
Default = inService(2).ro Enumeration .1.3.6.1.4.1.429.1.4.5.1.16 |
uds1CmdTableThe DS1 Command table contains an entry for each of the
manageable CSUs in the chassis. It provides a means
through which to take specific actions on one or more CSUs
in the chassis. SEQUENCE OF Uds1CmdEntry .1.3.6.1.4.1.429.1.4.6 |
uds1CmdEntryThere is one entry in the DS1 Command table per CSU in the
chassis. Uds1CmdEntry .1.3.6.1.4.1.429.1.4.6.1 |
uds1CmdIndexA unique value for each CSU in the chassis. The value of
uds1CmdIndex matches the value of the index for the
corresponding DS1 entity in the entity table of the chassis
MIB.ro INTEGER .1.3.6.1.4.1.429.1.4.6.1.1 |
uds1CmdMgtStationIdThis object is a generic read-write variable that a
Management Station (MS) can use to guarantee that the
results from a given command are the result of that
specific MS. Each MS must SET a unique value to this object
when doing commands and GET the value of this object
together with uds1CmdReqId and uds1CmdResult to detect
interference from other MSs.rw OCTET STRING .1.3.6.1.4.1.429.1.4.6.1.2 |
uds1CmdReqIdThis object contains the value of the request-id field in
the SNMP PDU which invoked the current or most recent
command on this DS1 interface. If the request-id is
unknown or undefined, this object contains the zero value.ro INTEGER .1.3.6.1.4.1.429.1.4.6.1.3 |
uds1CmdFunctionThis object identifies the command being requested.rw Enumeration .1.3.6.1.4.1.429.1.4.6.1.4 |
uds1CmdForceIn some cases, the DS1 interface may be in a state such
that certain commands could adversely affect connections.
In such cases, a command request with uds1CmdForce not
defined, or set to noForce will result in a warning. If
the operator elects to ignore such warnings, uds1CmdForce
can be set to force in a re-issued request and the command
will be carried out regardless of its potentially
hazzardous effects.rw Enumeration .1.3.6.1.4.1.429.1.4.6.1.5 |
uds1CmdParamThis object contains parameters that are specific to the
particular command being issued. In some cases, there will
be no additional parameters required.rw OCTET STRING .1.3.6.1.4.1.429.1.4.6.1.6 |
uds1CmdResultThis object contains the result of the most recently
requested command, or the value none(1) if no commands have
been requested since the last reset.ro Enumeration .1.3.6.1.4.1.429.1.4.6.1.7 |
uds1CmdCodeThe value of this object upon command completion indicates
a further description of what went wrong if the command was
unsuccessful.ro Enumeration .1.3.6.1.4.1.429.1.4.6.1.8 |
uds1TrapEnaTableA trap enable table that defines a column for every trap
that a DS1 entity can generate. SEQUENCE OF Uds1TrapEnaEntry .1.3.6.1.4.1.429.1.4.7 |
uds1TrapEnaEntryThere is one entry in this table for every CSU that exists
in the chassis. Uds1TrapEnaEntry .1.3.6.1.4.1.429.1.4.7.1 |
uds1TrapEnaIndexA unique value for each CSU in the chassis. The value of
uds1TrapEnaIndex matches the value of the index for the
corresponding DS1 entity in the entity table of the chassis
MIB.ro INTEGER .1.3.6.1.4.1.429.1.4.7.1.1 |
uds1TrapEnaYellowAlarmEnable the generation of an SNMP trap upon detection of a
yellow alarm condition on the specified DS1.rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.2 |
uds1TrapEnaRedAlarmEnable the generation of an SNMP trap upon detection of a
red alarm condition on the specified DS1.rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.3 |
uds1TrapEnaLossOfSignalEnable the generation of an SNMP trap upon detection of
loss of signal on the specified DS1.rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.4 |
uds1TrapEnaAlarmIndSignalEnable the generation of an SNMP trap upon detection of an
alarm indication signal (AIS) on the specified DS1.rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.5 |
uds1TrapEnaYellowAlarmClrEnable the generation of an SNMP trap upon detection of a
yellow alarm condition being cleared on the specified DS1.rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.6 |
uds1TrapEnaRedAlarmClrEnable the generation of an SNMP trap upon detection of a
red alarm condition being cleared on the specified DS1.rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.7 |
uds1TrapEnaLossOfSgnlClrEnable the generation of an SNMP trap upon detection of
loss of signal condition being cleared on the specified
DS1.rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.8 |
uds1TrapEnaAlrmIndSgnlClrEnable the generation of an SNMP trap upon detection of an
alarm indication signal (AIS) being cleared on the
specified DS1.rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.9 |
uds1TrapEnaContCrcAlrmEnable the generation of an SNMP trap upon detection of a
continuous CRC condition on the specified DS1.rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.10 |
uds1TrapEnaContCrcAlrmClrEnable the generation of an SNMP trap upon detection of the
clearing of a continuous CRC condition on the specified
DS1.rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.11 |
uds1TrapEnaPhysStateChngEnable the generation of an SNMP trap upon detection of a
change in the physical state of the specified DS1.rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.12 |
uds1TrapEnaDchanInSrvcEnable the generation of an SNMP trap upon detection of a
change in the service state of a D channel on this span
line from Out of Service, Maintenance or Standby to In
Service.
Default = disableAll(2).rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.13 |
uds1TrapEnaDchanOutOfSrvcEnable the generation of an SNMP trap upon detection of a
change in the service state of a D channel on this span
line from In Service to Out of Service, Maintenance or
Standby.
Default = disableAll(2).rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.14 |
uds1TrapEnaDs0InSrvcEnable the generation of an SNMP trap upon detection of a
change in the service state of a DS0 on this span line from
Out of Service to In Service.
Default = disableAll(2).rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.15 |
uds1TrapEnaDs0OutOfSrvcEnable the generation of an SNMP trap upon detection of a
change in the service state of a DS0 on this span line from
In Service to Out of Service.
Default = disableAll(2).rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.16 |
uds1TrapEnaMultiFrameEnable the generation of an SNMP trap upon detection of a
Multi-Frame Alignment condition on the specified DS1.
Default = disableAll(2).rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.17 |
uds1TrapEnaRemMultiFrameEnable the generation of an SNMP trap upon detection of a
Remote Multi-Frame Alignment condition on the specified
DS1. Default = disableAll(2).rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.18 |
uds1TrapEnaMultiFrmClrEnable the generation of an SNMP trap upon detection of
clearing a Multi-Frame Alignment condition on the specified
DS1. Default = disableAll(2).rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.19 |
uds1TrapEnaRemMultiFrmClrEnable the generation of an SNMP trap upon detection of
clearing a Remote Multi-Frame Alignment condition on the
specified DS1. Default = disableAll(2).rw Enumeration .1.3.6.1.4.1.429.1.4.7.1.20 |