NMC-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
173
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
173 total| Object Name |
|---|
usr OBJECT IDENTIFIER .1.3.6.1.4.1.429 |
RFC1213-MIB Unknown .1.3.6.1.4.1.429 |
nas OBJECT IDENTIFIER .1.3.6.1.4.1.429.1 |
nmc OBJECT IDENTIFIER .1.3.6.1.4.1.429.1.2 |
nmcCfg OBJECT IDENTIFIER .1.3.6.1.4.1.429.1.2.1 |
nmcCfgSystemTimeThis parameter is used to set and read the current time as
kept by the NMC's real-time clock. It should be set to the
local time in the place where the chassis is physically
located. The real-time clock has the capability of
maintaining correct time for short durations without power.rw DisplayString .1.3.6.1.4.1.429.1.2.1.1 |
nmcCfgSystemDateThis parameter is used to set and read the current date as
kept by the NMC's real-time clock. It should be set to the
local date where the chassis is physically located.rw DisplayString .1.3.6.1.4.1.429.1.2.1.2 |
nmcGmtimeThis object reflects the current time in Greenwich Mean
Time (GMT). The value of this object is sent in USR's
enterprise specific SNMP trap messages for use by the
receiving Management Stations.ro INTEGER .1.3.6.1.4.1.429.1.2.1.3 |
nmcTimezoneThis object should be set to reflect the timezone in which
the chassis is physically located. It is used in the
conversion from local time to Greenwich Mean Time (GMT).
The timezones are named for the number of hours by which
GMT differs from local time.
Default=gmtPlus0(21).rw Enumeration .1.3.6.1.4.1.429.1.2.1.4 |
nmcCfgAuthFailTrapEnableThis object indicates whether or not the SNMP Proxy Agent
running in the Network Management Card is to send a trap
upon reception of an SNMP message that was not properly
authenticated. MIB-I and II require a mechanism for
enabling/disabling generation of this trap.rw Enumeration .1.3.6.1.4.1.429.1.2.1.5 |
nmcDaySavingTimeThe value of this object determines whether or not the NMC
will honor daylight savings time when converting from local
time to Greenwich Mean Time (GMT).rw Enumeration .1.3.6.1.4.1.429.1.2.1.6 |
nmcCfgWanDialOutPhoneNumThis is the phone number that the NMC will use to dial a
modem that is connected to the WAN port if there is no
existing connection when the NMC tries to send and IP
datagram out that port.rw DisplayString .1.3.6.1.4.1.429.1.2.1.7 |
nmcCfgAtStringThis object is the user defined AT string that will be used
to configure a modem connected to the NMC's WAN port if the
NMC needs to dial out to make a connection.rw DisplayString .1.3.6.1.4.1.429.1.2.1.8 |
nmcPowerUpAutoCfgEnableThis parameter defines whether or not to automatically
configure cards when they are inserted into the chassis or
when the chassis is powered on. If set to do the
autoconfigure, the values used to configure the cards will
be those that were last saved to the NMC's NVRAM. For
cards that do not match the values in NVRAM, those cards
will be configured with default values.rw Enumeration .1.3.6.1.4.1.429.1.2.1.9 |
nmcCfgNumWanRetriesThis will specify the number of attempts to be made by
port_write_task() to send the packet out of the WAN port
while doing a dial up connection. The default is 0 which
means the number of retries is disabled and it will keep
trying to transmit the same packet for ever until it
succeeds.rw INTEGER .1.3.6.1.4.1.429.1.2.1.10 |
nmcCfgWanRetryPauseThe amount of time in seconds that the NMC will pause
between attempts to transmit a packet. The default value
for this object is 30.rw INTEGER .1.3.6.1.4.1.429.1.2.1.11 |
nmcCfgWanRetrySuspendTimeThe Time period in seconds for which the WAN port should
suspend its attempts to send out the packet. This time
period applies when the number of failures has reached a
configured maximum. It may resume its retries after the
time period.rw INTEGER .1.3.6.1.4.1.429.1.2.1.12 |
nmcCfgNumFailBefSuspendThe number of connection failures to allow before
suspending retries.rw INTEGER .1.3.6.1.4.1.429.1.2.1.13 |
nmcCfgLogSrvrSelectThe server selection for event logging.
Default=none(3).ro Enumeration .1.3.6.1.4.1.429.1.2.1.14 |
nmcCfgLogPriSrvrAddrThe primary logging server's IP address.rw IpAddress .1.3.6.1.4.1.429.1.2.1.15 |
nmcCfgLogSecSrvrAddrThe secondary logging server's IP address.rw IpAddress .1.3.6.1.4.1.429.1.2.1.16 |
nmcCfgLogUdpPortNumThe logging server's UDP port number.
Default=1646.rw INTEGER .1.3.6.1.4.1.429.1.2.1.17 |
nmcCfgLogRetryCntThe NMC logging client transmission retry
count.
Default=3.rw INTEGER .1.3.6.1.4.1.429.1.2.1.18 |
nmcCfgLogCallStatGrpSelThe optional call statistics groups included in log
messages. Groups are Usage(1), Data Transfer(2),
Performance(3), Operating Mode(4) and RMMIE(5). Group 1 is
always sent. Groups 2-5 are optional.
Default = none(1).rw Enumeration .1.3.6.1.4.1.429.1.2.1.19 |
nmcCfgLogMD5CalcThis Optional Object will indicate to the accounting Client
whether to calculate MD5 for accounting request message or
not. default=disable.rw Enumeration .1.3.6.1.4.1.429.1.2.1.20 |
nmcCfgTFTPTimeoutThis object will be used to set up the timeout for the TFTP
retries. The default would be 12 sec and the maximum
allowed timeout would be 30 sec.rw INTEGER .1.3.6.1.4.1.429.1.2.1.21 |
nmcCfgDnsPriSrvrAddrThe primary DNS server's IP address.rw IpAddress .1.3.6.1.4.1.429.1.2.1.22 |
nmcCfgDnsSecSrvrAddrThe secondary DNS server's IP address.rw IpAddress .1.3.6.1.4.1.429.1.2.1.23 |
nmcCfgLog3SrvrAddrThe third backup logging server IP address to use.rw IpAddress .1.3.6.1.4.1.429.1.2.1.24 |
nmcCfgLog4SrvrAddrThe fourth backup logging server IP address to use.rw IpAddress .1.3.6.1.4.1.429.1.2.1.25 |
nmcCfgLog5SrvrAddrThe fifth backup logging server IP address to use.rw IpAddress .1.3.6.1.4.1.429.1.2.1.26 |
nmcCfgLog6SrvrAddrThe sixth backup logging server IP address to use.rw IpAddress .1.3.6.1.4.1.429.1.2.1.27 |
nmcCfgLog7SrvrAddrThe seventh backup logging server IP address to use.rw IpAddress .1.3.6.1.4.1.429.1.2.1.28 |
nmcCfgLog8SrvrAddrThe eighth backup logging server IP address to use.rw IpAddress .1.3.6.1.4.1.429.1.2.1.29 |
nmcCfgLogSrvrNameThe host name of the logging server. Used to resolve
logging server IP addresses through DNS query requests from
the resolver.rw DisplayString .1.3.6.1.4.1.429.1.2.1.30 |
nmcCfgDnsRetryCntThe maximum number of retries that will be attempted to
query a DNS before trying the secondary DNS.rw INTEGER .1.3.6.1.4.1.429.1.2.1.31 |
nmcCfgDnsUdpPortNumThe logging server's UDP port number.
Default=53.rw INTEGER .1.3.6.1.4.1.429.1.2.1.32 |
nmcCfgDnsSrvrSelectThe server selection for DNS.
Default=none(1).ro Enumeration .1.3.6.1.4.1.429.1.2.1.33 |
nmcCfgLogDnsEnaIndicates whether logging server host address DNS
resolution is enabled or disabled. Disabled, the logging
server addresses are taken from the log server address
objects.rw Enumeration .1.3.6.1.4.1.429.1.2.1.34 |
nmcCfgLogStatusIntervalThis value defines the interval in seconds between
Status-Server requests for a failed RADIUS Accounting
server connection.
Default=30.rw INTEGER .1.3.6.1.4.1.429.1.2.1.35 |
nmcCfgDnsSrvrFailureThis value defines the failure reason for last failure of
DNS resolver query.ro Enumeration .1.3.6.1.4.1.429.1.2.1.36 |
nmcCfgLogSrvrFailureThis value defines the failure reason for the last failure
of RADIUS accounting server access.ro Enumeration .1.3.6.1.4.1.429.1.2.1.37 |
nmcCfgSessionIDNewFmtThis Object is used to Enable/Disable the New Session ID
Format. Default is Disable.rw Enumeration .1.3.6.1.4.1.429.1.2.1.38 |
nmcStat OBJECT IDENTIFIER .1.3.6.1.4.1.429.1.2.2 |
nmcStatStatusThis object will indicate the general status or health of
the Network Management Card.ro Enumeration .1.3.6.1.4.1.429.1.2.2.1 |
nmcStatDramInstalledThis object indicates the amount of dynamic RAM currently
installed on the Network Management Card. The units for
this value are kilobytes.ro INTEGER .1.3.6.1.4.1.429.1.2.2.2 |
nmcStatNVRAMInstalledThis object indicates the amount of non-volatile RAM
currently installed on the Network Management Card. The
units for this value are kilobytes.ro INTEGER .1.3.6.1.4.1.429.1.2.2.3 |
nmcStatEventIdThis value increments once for each network management
event detected by the NMC. It is used to correlate SNMP
traps with events that occured in the system.ro INTEGER .1.3.6.1.4.1.429.1.2.2.4 |
nmcStatTemperatureThis object reflects the current temperature in the NAS
chassis, as detected by the NMC. The value of this object
indicates the temperature in degree Celcius.ro INTEGER .1.3.6.1.4.1.429.1.2.2.5 |
nmcStatPowerUpTstFailuresThis object contains the number of power up tests which
failed during the power up of the NMC card.ro Counter .1.3.6.1.4.1.429.1.2.2.6 |
nmcStatPowerUpTstFailBMapThis object defines a bit map which contains a one in the
postion that indicates a power up test failure. The number
returned is an integer that represents which power up
test(s) that have failed. (e.g. a return value of three
would mean power up tests 1 & 2 failed since bits 00000011
in the least significant byte would be set.)ro INTEGER .1.3.6.1.4.1.429.1.2.2.7 |
nmcStatTestResultThis object contains the bit mapped result of the request
to perform a self test. A non zero value indicates that
there has been one or more self test failures.ro INTEGER .1.3.6.1.4.1.429.1.2.2.8 |
nmcStatCompSwVerThis object contains the software compatibility version.ro DisplayString .1.3.6.1.4.1.429.1.2.2.9 |
nmcStatPktBusClkSrcThe source of the backplane packet bus clock.ro Enumeration .1.3.6.1.4.1.429.1.2.2.10 |
nmcStatNmcPktBusClkThe NMC's packet bus clock status.ro Enumeration .1.3.6.1.4.1.429.1.2.2.11 |
nmcStatRedLedThis Object will return the Reason why the Hub Status LED
is RED.ro Enumeration .1.3.6.1.4.1.429.1.2.2.12 |
nmcAuxIn1StsThis Object shows status of Aux Input port1.ro Enumeration .1.3.6.1.4.1.429.1.2.2.13 |
nmcAuxIn2StsThis Object shows status of Aux Input port2.ro Enumeration .1.3.6.1.4.1.429.1.2.2.14 |
nmcAuxOut1StsThis Object shows status of Aux Output port1.ro Enumeration .1.3.6.1.4.1.429.1.2.2.15 |
nmcAuxOut2StsThis Object shows status of Aux Output port2.ro Enumeration .1.3.6.1.4.1.429.1.2.2.16 |
nmcTrap OBJECT IDENTIFIER .1.3.6.1.4.1.429.1.2.3 |
nmcTrapSequenceNumberThis object increments every time a trap is generated by
the NMC. This object is sent in the var-bind list of each
trap and can be used by management stations to detect when
a trap has been lost.ro INTEGER .1.3.6.1.4.1.429.1.2.3.1 |
nmcTrapDestTableThis table defines the places to which traps are to be
sent. These places may refer to management consoles, or
other alarm collection processes. SEQUENCE OF NmcTrapDestEntry .1.3.6.1.4.1.429.1.2.3.2 |
nmcTrapDestEntryThere is an entry in this table for each destination to
which the NMC is to send SNMP traps. NmcTrapDestEntry .1.3.6.1.4.1.429.1.2.3.2.1 |
nmcTrapDestIPThis object identifies the IP address to be used for
sending traps to the destination identified by
nmcTrapDestDescr.ro IpAddress .1.3.6.1.4.1.429.1.2.3.2.1.1 |
nmcTrapDestCommunityThis object identifies the community string to be used when
sending traps to the destination identified by
nmcTrapDestDescr.rw OCTET STRING .1.3.6.1.4.1.429.1.2.3.2.1.2 |
nmcTrapDestDescrThis object contains a plain text description of the trap
destination to which this entry pertains.rw DisplayString .1.3.6.1.4.1.429.1.2.3.2.1.3 |
nmcArTrapIdA single user defined value can be configured through
AutoResponse script MIB objects to be sent to the
management stations when a NMC AutoResponse SNMP TRAP
occurs.ro INTEGER .1.3.6.1.4.1.429.1.2.3.3 |
nmcCmd OBJECT IDENTIFIER .1.3.6.1.4.1.429.1.2.4 |
nmcCmdMgtStationIdThis object is a generic read-write variable that a
Management Station (MS) can use to guarantee that the
results from a given command are the results of a command
issued by that specific MS. Each MS must SET a unique
value to this object when doing commands and GET the value
of this object together with ds0CmdReqId and ds0CmdResult
to detect interference from other MSs.rw OCTET STRING .1.3.6.1.4.1.429.1.2.4.1 |
nmcCmdReqIdThis object contains the value of the request-id field in
the SNMP PDU which invoked the current or most recent
command or test on this Network Management Card. If the
request-id is unknown or undefined, this object contains
the value zero.rw INTEGER .1.3.6.1.4.1.429.1.2.4.2 |
nmcCmdFunctionThis object contains the value which decsribe the command
which is being invoked.rw Enumeration .1.3.6.1.4.1.429.1.2.4.3 |
nmcCmdForceIn some cases, the Network Managment Card may be in a state
such that certain commands could adversely affect
operations. In such cases, a command request with this
object not present or set to noForce will result in a
warning. If the operator elects to ignore such warnings,
this object can be set to force in a subsequent issue of
the command to cause the command to be carried out
regardless of its potentially hazzardous effects.rw Enumeration .1.3.6.1.4.1.429.1.2.4.4 |
nmcCmdParamThis object contains parameters that are specific to the
particular command being issued. In some cases, there will
be no additional parameters required.rw OCTET STRING .1.3.6.1.4.1.429.1.2.4.5 |
nmcCmdResultThis object contains the result of the most recently
requested command or test, or the value none(1) if no
commands have been requested since the last reset.ro Enumeration .1.3.6.1.4.1.429.1.2.4.6 |
nmcCmdCodeThe value of this object upon command completion indicates
a further description of what went wrong if the command was
unsuccessful. In the case of tests, a bit mapped result of
each of the sub-tests performed appears in the
nmcStatTestResult object.ro Enumeration .1.3.6.1.4.1.429.1.2.4.7 |
nmcHs OBJECT IDENTIFIER .1.3.6.1.4.1.429.1.2.6 |
nmcHsDialInOutNamePromptThis is the first prompt that appears when users establish
a connection with a security modem. It should serve to
identify the system and prompt users to enter their name.rw DisplayString .1.3.6.1.4.1.429.1.2.6.1 |
nmcHsDialInOutPsswdPromptThis prompt appears after a valid response has been made to
the previous prompt (i.e., name string followed by CR/LF),
and prompts users to enter their password.rw DisplayString .1.3.6.1.4.1.429.1.2.6.2 |
nmcHsDialBackNamePromptThis prompt only appears when users are configured for dial
back security (to either a stored or entered number). It
is also only issued when the Request Login Validation on
Dial-Back field is enabled for the user in the RADIUS user
database. This prompt should be different than the name
prompt used when users first log into the system.rw DisplayString .1.3.6.1.4.1.429.1.2.6.3 |
nmcHsDialBackPsswdPromptThis prompt appears after a valid response to the prior
prompt, and prompts users to enter their password.rw DisplayString .1.3.6.1.4.1.429.1.2.6.4 |
nmcHsDialBackPhonePromptThis prompt only appears if you have configured the user
for dial back entered mode in the RADIUS user database. It
prompts the user to enter the phone number at which the
system can call them back.rw DisplayString .1.3.6.1.4.1.429.1.2.6.5 |
nmcHsDialBackPendPromptThis message only appears if you configure users for a dial
back mode (to either a stored or entered number) in the
RADIUS user database. It confirms to users that they have
logged in successfully, and lets them know that the system
has reserved a modem to call them back.rw DisplayString .1.3.6.1.4.1.429.1.2.6.6 |
nmcHsMdmSelectPromptThis message only appears if a user is configured for dial
back in the RADIUS database and that this record has the
Request Dial Back Modem Selection field enabled. The
system displays a list of allowed dial back modems that
have been entered for this user. Users must enter the
number that appears on the menu next to their choice.rw DisplayString .1.3.6.1.4.1.429.1.2.6.7 |
nmcHsLoginFailedMsgThis message appears when users fail to enter a valid
name/password combination.rw DisplayString .1.3.6.1.4.1.429.1.2.6.8 |
nmcHsPhoneRestrictPromptThis message appears when users are prompted for a dial
back phone number and the entered number violates the
allowed numbers specified in the Call Restriction List.rw DisplayString .1.3.6.1.4.1.429.1.2.6.9 |
nmcHsInvalidMdmSelecMsgThis message appears when users configured for dial back
with the Request Dial-Back Modem Selection field enabled,
select a modem to which they are not allowed access (as
specified in the list of allowed Dial-Back modems).rw DisplayString .1.3.6.1.4.1.429.1.2.6.10 |
nmcHsNoMdnsAvailMsgThis message appears when the system is unable to reserve a
modem for dial-back that was either selected by the user or
defined in it's list of Allowed Dial Back modems.rw DisplayString .1.3.6.1.4.1.429.1.2.6.11 |
nmcHsConnectSuccessMsgThis message confirms that users have successfully
compleated their login and may proceed with either their
dial-in or dial-out call.rw DisplayString .1.3.6.1.4.1.429.1.2.6.12 |
nmcHsNewPasswordPromptThis prompt only appears when a users password has expired.
It is issued once for the new password and then again for
re-issue of the new password.rw DisplayString .1.3.6.1.4.1.429.1.2.6.13 |
nmcHsChangePasswordMsgThis message appears during name/password authentication
when the user's password has expired. This message is
immediately followed by the enter new password prompt.rw DisplayString .1.3.6.1.4.1.429.1.2.6.14 |
nmcHsPromptRspTimeoutThis value represents the number of seconds in which users
must respond to each prompt. Users failing to respond
within the specified time are disconnected, and a Dial
Security login failure trap is generated. Any login
failures of this type also apply to the user blacklist
function if a valid user name has been entered. This field
takes precidence over the modem's inactivity timer during a
security login. The default for this object is
30(seconds).rw INTEGER .1.3.6.1.4.1.429.1.2.6.15 |
nmcHsPromptRspAttemptsThis value represents the number of tries the user is
allowed per prompt during any one security session. If
this number is reached, the call is terminated. For the
purposes of retry limiting, the user name and password are
treated as a single prompt. This means that if a valid
name and an invalid password are entered, the failure is
counted against both the Prompt Response Attempt Limit and
the Failed Logins Before Blacklist. The default for this
object is 1.rw INTEGER .1.3.6.1.4.1.429.1.2.6.16 |
nmcHsPromptRspEchoEnaWhen enabled, this option instructs the NMC to echo the
user's typed responses back to the users screen. Password
responses are echoed as 'X's. The default for this option
is disabled.rw Enumeration .1.3.6.1.4.1.429.1.2.6.17 |
nmcHsDialBackDelayThis object defines the number of seconds to wait between
successive dial back attempts; i.e., the time the NMC waits
before attempting the next dial back when it was unable to
connect. The default is 30 seconds.rw INTEGER .1.3.6.1.4.1.429.1.2.6.18 |
nmcHsDialBackAttemptsThis object defines the number of times that the NMC will
attempt to dial back a dial in user configured for dial
back when successive dial back attempts fail. The default
for this object is one.rw INTEGER .1.3.6.1.4.1.429.1.2.6.19 |
nmcHsSecuritySrvrAddrThis object identifies the IP address of the Primary RADIUS
security server where the NMC RADIUS client sends requests.rw IpAddress .1.3.6.1.4.1.429.1.2.6.20 |
nmcHsSecuritySrvrPortThis object identifies the UDP port where the NMC's RADIUS
client issues requests to the RADIUS security server. The
default port is 1645.rw INTEGER .1.3.6.1.4.1.429.1.2.6.21 |
nmcHsSecuritySrvrRetriesThis object identifies the number of retries that the NMC's
RADIUS client will preform when attempting to send requests
to a RADIUS security server. The default retry number is 1.rw INTEGER .1.3.6.1.4.1.429.1.2.6.22 |
nmcHsMdmAttemptLimitThis value represents the number of times an attempt can be
made to login on any one modem without success. If this
value is exceeded and the mdmLoginAttemptLimExceeded trap
has been enabled, then the mdmLoginAttemptLimExceeded trap
is generated. Default = 3.rw INTEGER .1.3.6.1.4.1.429.1.2.6.23 |
nmcHsServerUnavailableThis option specifies whether to deny or allow a call when
a dial security server is unreachable.
Default =
denyCall(1).rw Enumeration .1.3.6.1.4.1.429.1.2.6.24 |
nmcHsServerSelectServer Selection for RADIUS Security. Default=none(3).ro Enumeration .1.3.6.1.4.1.429.1.2.6.25 |
nmcHsSecondarySrvrAddrThis object identifies the IP address of the Secondary
RADIUS Security Server.rw IpAddress .1.3.6.1.4.1.429.1.2.6.26 |
nmcHsDiPasswdEnaDisThis Optional Object will Enable/Disable PASSWORD prompt
for Dial-In Hub Security. Default is Enable(1).rw Enumeration .1.3.6.1.4.1.429.1.2.6.27 |
nmcHsSecurity3SrvrAddrThis object identifies the IP address of the 3rd RADIUS
Security backup server.rw IpAddress .1.3.6.1.4.1.429.1.2.6.28 |
nmcHsSecurity4SrvrAddrThis object identifies the IP address of the 4th RADIUS
Security backup server.rw IpAddress .1.3.6.1.4.1.429.1.2.6.29 |
nmcHsSecurity5SrvrAddrThis object identifies the IP address of the 5th RADIUS
Security backup server.rw IpAddress .1.3.6.1.4.1.429.1.2.6.30 |
nmcHsSecurity6SrvrAddrThis object identifies the IP address of the 6th RADIUS
Security backup server.rw IpAddress .1.3.6.1.4.1.429.1.2.6.31 |
nmcHsSecurity7SrvrAddrThis object identifies the IP address of the 7th RADIUS
Security backup server.rw IpAddress .1.3.6.1.4.1.429.1.2.6.32 |
nmcHsSecurity8SrvrAddrThis object identifies the IP address of the 8th RADIUS
Security backup server.rw IpAddress .1.3.6.1.4.1.429.1.2.6.33 |
nmcHsSecuritySrvrNameIdentifies the host name of the RADIUS Security server used
to resolve IP addresses through DNS queries.rw DisplayString .1.3.6.1.4.1.429.1.2.6.34 |
nmcHsSecuritySrvrDnsEnaIndicates RADIUS Security server IP addresses are resolved
through DNS queries. If disabled, the Security server
address objects are used.
Default=disabledrw Enumeration .1.3.6.1.4.1.429.1.2.6.35 |
nmcHsSecurityStatusIntThis value defines the interval in seconds between
Status-Server requests for a failed RADIUS Security server
connection.
Default=30.rw INTEGER .1.3.6.1.4.1.429.1.2.6.36 |
nmcHsSecurityFailureThis value defines the failure reason for the last failure
of RADIUS Security server access.ro Enumeration .1.3.6.1.4.1.429.1.2.6.37 |
nmcTe OBJECT IDENTIFIER .1.3.6.1.4.1.429.1.2.7 |
nmcTeDialOutLoginFailEnable/disable for the trap generated when a dial out login
security session has failed.rw Enumeration .1.3.6.1.4.1.429.1.2.7.1 |
nmcTeDialInLoginFailEnable/disable for the trap generated when a dial in login
security session has failed.rw Enumeration .1.3.6.1.4.1.429.1.2.7.2 |
nmcTeDialOutRestrictNumEnable/disable for the trap generated when a dial out
security session has failed as a result of attempting to
dial a restricted phone number.rw Enumeration .1.3.6.1.4.1.429.1.2.7.3 |
nmcTeDialBackRestrictNumEnable/disable for the trap generated when a dial back
security session has failed as a result of attempting to
dial a restricted phone number.rw Enumeration .1.3.6.1.4.1.429.1.2.7.4 |
nmcTeUserBlacklistEnable/disable for the trap generated when a security user
has reached their final failed login attempt number and is
now being blacklisted.rw Enumeration .1.3.6.1.4.1.429.1.2.7.5 |
nmcTeUserBlacklistLoginEnable/disable for the trap generated when a security login
attempt by a currently blacklisted user has occurred.rw Enumeration .1.3.6.1.4.1.429.1.2.7.6 |
nmcTeRespAttmptLimExceedEnable/disable for the trap generated when a security user
has failed to issue a valid response to a particular
security prompt before the configured limit.rw Enumeration .1.3.6.1.4.1.429.1.2.7.7 |
nmcTeLoginAttmptLimExceedEnable/disable for the trap generated when a security
session has failed because the indicated user does not
appear in the security user database.rw Enumeration .1.3.6.1.4.1.429.1.2.7.8 |
nmcTeLogSrvrLossEnable/disable for the trap generated when communication
with a logging server has been lost.rw Enumeration .1.3.6.1.4.1.429.1.2.7.9 |
nmcTeSecSrvrLossEnable/disable for the trap generated when communication
with a security server has been lost.rw Enumeration .1.3.6.1.4.1.429.1.2.7.10 |
nmcTeSinglePbClockFailEnable/disable for the trap generated when the NMC detects
that there is a packet bus clock failure in a single
slot.
Default=enable(1).rw Enumeration .1.3.6.1.4.1.429.1.2.7.11 |
nmcTePbClockSwitchEnable/disable for the trap generated when the NMC detects
that there is a packet bus clock failure in multiple slots
and the NMC has assumed the role of clock
master.
Default=enable(1).rw Enumeration .1.3.6.1.4.1.429.1.2.7.12 |
nmcTePbClockFailEnable/disable for the trap generated when the NMC detects
that the packet bus clock on the NMC daughter board pcb has
failed. Check status of nmcStatPktBusClkSrc to determine
if the NMC was acting as clock master.
Default=enable(1).rw Enumeration .1.3.6.1.4.1.429.1.2.7.13 |
nmcTeDnsSrvrLossEnable/disable for the trap generated when communication
with the primary and secondary DNS server has been lost.rw Enumeration .1.3.6.1.4.1.429.1.2.7.14 |
nmcTeNtpSrvrLossEnable/disable for the trap generated when communication
with all NTP servers has failed.rw Enumeration .1.3.6.1.4.1.429.1.2.7.15 |
nmcTeNtpSrvrRestoreEnable/disable for the trap generated when communication
with the NTP server has been restored.rw Enumeration .1.3.6.1.4.1.429.1.2.7.16 |
nmcTeNtpSrvrDegradedEnable/disable for the trap generated when communication
with the primary NTP server has failed, but the secondary
has been restored.rw Enumeration .1.3.6.1.4.1.429.1.2.7.17 |
nmcTeDnsSrvrRestoreEnable/disable for the trap generated when communication
with the primary DNS server has been
restored.
Default=disable.rw Enumeration .1.3.6.1.4.1.429.1.2.7.18 |
nmcTeDnsSrvrDegradedEnable/disable for the trap generated when communication
with the primary DNS server has failed, but the secondary
DNS server is operational.
Default=disabled.rw Enumeration .1.3.6.1.4.1.429.1.2.7.19 |
nmcTeLogSrvrRestoreEnable/disable for the trap generated when communication
with a logging server has been restored.rw Enumeration .1.3.6.1.4.1.429.1.2.7.20 |
nmcTeLogSrvrGroupOperEnable/disable for the trap generated when the
communication with the group of logging servers is
operational with the primary server in service.rw Enumeration .1.3.6.1.4.1.429.1.2.7.21 |
nmcTeLogSrvrGroupDegrEnable/disable from the trap generated when the
communication with the group of logging servers has
degraded with a non-primary server in service.rw Enumeration .1.3.6.1.4.1.429.1.2.7.22 |
nmcTeLogSrvrGroupNonOpEnable/disable for the trap generated when the
communication with the group of logging servers is
non-operational.rw Enumeration .1.3.6.1.4.1.429.1.2.7.23 |
nmcTeSecSrvrRestoreEnable/disable for the trap generated when communication
with the RADIUS Security server has been
restored.
Default=disabledrw Enumeration .1.3.6.1.4.1.429.1.2.7.24 |
nmcTeSecSrvrGroupOperEnable/disable for the trap generated when communication to
the RADIUS Security server group becomes
operational.
Default=disabledrw Enumeration .1.3.6.1.4.1.429.1.2.7.25 |
nmcTeSecSrvrGroupDegrEnable/disable for the trap generated when communication to
the RADIUS Security server group becomes degraded because
of failure to contact primary server.
Default=disabledrw Enumeration .1.3.6.1.4.1.429.1.2.7.26 |
nmcTeSecSrvrGroupNonOpEnable/disable for the trap generated when communication to
the RADIUS Security server group becomes non-operational
because of failure to contact any Security
servers.
Default=disabledrw Enumeration .1.3.6.1.4.1.429.1.2.7.27 |
nmcUiCfg OBJECT IDENTIFIER .1.3.6.1.4.1.429.1.2.8 |
nmcUiCfgLanIPAddrThis contains the IP address of the LAN interface.rw IpAddress .1.3.6.1.4.1.429.1.2.8.1 |
nmcUiCfgLanSubnetMaskThis specifies the subnet mask for LAN interface.rw IpAddress .1.3.6.1.4.1.429.1.2.8.2 |
nmcUiCfgWanIPAddrThis specifies the IP address for the WAN interface.rw IpAddress .1.3.6.1.4.1.429.1.2.8.3 |
nmcUiCfgWanSubnetMaskThis specifies the Subnet mask for the WAN interface.rw IpAddress .1.3.6.1.4.1.429.1.2.8.4 |
nmcUiCfgDefaultGwyIPThis specifies the address of the Gateway to which the IP
will forward those packets whose net ID does not match the
net ID of either interface.rw IpAddress .1.3.6.1.4.1.429.1.2.8.5 |
nmcUiCfgLocalTrIeeeAddrThis gives the IEEE physical address of the Token Ring
interface.rw OCTET STRING .1.3.6.1.4.1.429.1.2.8.6 |
nmcUiCfgPrivateStringThis specifies the SNMP read-write community
string.
Default='private'.rw DisplayString .1.3.6.1.4.1.429.1.2.8.7 |
nmcUiCfgLanIfEnableThis parameter controls the enable/disable of the LAN
interface.rw Enumeration .1.3.6.1.4.1.429.1.2.8.8 |
nmcUiCfgPublicStringThis specifies the SNMP read-only community
string.
Default='public'.rw DisplayString .1.3.6.1.4.1.429.1.2.8.9 |
nmcUiCfgRouteEnableThis Parameter controls the ability of the NMC to route
traffic between it's LAN and SLIP interfaces, Default =
enable(1).rw Enumeration .1.3.6.1.4.1.429.1.2.8.10 |
nmcUiCfgUiSlipCfgThis is used to configure the UI port as SLIP or UI.
Default=UI.rw Enumeration .1.3.6.1.4.1.429.1.2.8.11 |
nmcUiCfgWan2IpAddrThis contains the IP address of second SLIP port.rw IpAddress .1.3.6.1.4.1.429.1.2.8.12 |
nmcUiCfgWan2SubnetMaskThis contains SubnetMask for Second Slip port.rw IpAddress .1.3.6.1.4.1.429.1.2.8.13 |
nmcUiCfgInactiveTimeThis parameter is in minutes it is used as an Inactivity
time on the UI port. The Default is 3 minutes and 0 minutes
disables the feature.rw INTEGER .1.3.6.1.4.1.429.1.2.8.14 |
nmcUiCfgPasswordThis parameter is used to Enable or Disable the PASSWORD
protection for UI functions. Default = disabled.rw Enumeration .1.3.6.1.4.1.429.1.2.8.15 |
nmcAuth OBJECT IDENTIFIER .1.3.6.1.4.1.429.1.2.9 |
nmcAuthAccTableThis table defines which management stations are allowed
access to the NMC. SEQUENCE OF NmcAuthAccEntry .1.3.6.1.4.1.429.1.2.9.1 |
nmcAuthAccEntryThere is an entry for each management station allowd access
to the NMC. NmcAuthAccEntry .1.3.6.1.4.1.429.1.2.9.1.1 |
nmcAuthAccIpAddrThis is the IP address of the station allowed access to the
NMC.ro IpAddress .1.3.6.1.4.1.429.1.2.9.1.1.1 |
nmcAuthAccNetMaskThis is the network mask of the station allowed access to
the NMC.rw IpAddress .1.3.6.1.4.1.429.1.2.9.1.1.2 |
nmcAuthAccDescrThis is the description of the station allowed access to
the NMC.rw DisplayString .1.3.6.1.4.1.429.1.2.9.1.1.3 |
nmcNtp OBJECT IDENTIFIER .1.3.6.1.4.1.429.1.2.10 |
nmcNtpSrvrPrimAddrThe primary NTP server's IP address.rw IpAddress .1.3.6.1.4.1.429.1.2.10.1 |
nmcNtpSrvrSecdAddrThe secondary NTP server's IP address. This server is only
accessed when responses from the primary have failed.rw IpAddress .1.3.6.1.4.1.429.1.2.10.2 |
nmcNtpSyncIntervalThe synchronization interval between successive NTP
requests in seconds.rw INTEGER .1.3.6.1.4.1.429.1.2.10.3 |
nmcNtpOperationalModeThe operational mode of the NTP client. In unicast mode,
the NTP requests the current time from the primary NTP and
uses the secondary NTP as a backup.rw Enumeration .1.3.6.1.4.1.429.1.2.10.4 |
nmcNtpLastSyncTimeThe time since the last successful NTP synchronization in
seconds.ro INTEGER .1.3.6.1.4.1.429.1.2.10.5 |
nmcNtpLastSyncServerThe last NTP server used to successfully synchronize time.ro Enumeration .1.3.6.1.4.1.429.1.2.10.6 |
nmcNtpLastFailedTimeThe time since the last failed NTP synchronization attempt
in seconds.ro INTEGER .1.3.6.1.4.1.429.1.2.10.7 |
nmcNtpLastFailedServerThe last NTP server used in a failed attempt to synchronize
time.ro Enumeration .1.3.6.1.4.1.429.1.2.10.8 |