TROPIC-SYNCE-MIB
AI MIB Summary
The TROPIC-SYNCE-MIB module enables the monitoring and management of Synchronous Ethernet (IEEE 802.1AS) attributes on Tropic Networks hardware, specifically tracking synchronization status, clock quality levels, and traceability paths to ensure network timing integrity.
Synchronous Ethernet MIB attributes.
Main OID:
tnSyncEMibModule.1.3.6.1.4.1.7483.1.1.2.2.4.6
95
Objects
Active
Status
11
Dependencies
Imported Objects
Objects
95 total| Object Name |
|---|
tnSyncEMibModuleSynchronous Ethernet MIB attributes. MODULE-IDENTITY .1.3.6.1.4.1.7483.1.1.2.2.4.6 |
tnSyncEConf OBJECT IDENTIFIER .1.3.6.1.4.1.7483.2.2.4.8.1 |
tnSyncEGroups OBJECT IDENTIFIER .1.3.6.1.4.1.7483.2.2.4.8.1.1 |
tnSyncEGroup. Unknown .1.3.6.1.4.1.7483.2.2.4.8.1.1.1 |
tnSyncELineRefGroup. Unknown .1.3.6.1.4.1.7483.2.2.4.8.1.1.2 |
tnSyncEControlGroup. Unknown .1.3.6.1.4.1.7483.2.2.4.8.1.1.3 |
tnSyncEPortGroup. Unknown .1.3.6.1.4.1.7483.2.2.4.8.1.1.4 |
tnSyncEStationClockGroup. Unknown .1.3.6.1.4.1.7483.2.2.4.8.1.1.5 |
tnSyncEBITSPortGroup. Unknown .1.3.6.1.4.1.7483.2.2.4.8.1.1.6 |
tnWanGroup. Unknown .1.3.6.1.4.1.7483.2.2.4.8.1.1.7 |
tnSyncEPacketswitchControlGroup. Unknown .1.3.6.1.4.1.7483.2.2.4.8.1.1.8 |
tnSyncECompliances OBJECT IDENTIFIER .1.3.6.1.4.1.7483.2.2.4.8.1.2 |
tnSyncECompliance. Unknown .1.3.6.1.4.1.7483.2.2.4.8.1.2.1 |
tnSyncEObjs OBJECT IDENTIFIER .1.3.6.1.4.1.7483.2.2.4.8.2 |
tnSyncEBasics OBJECT IDENTIFIER .1.3.6.1.4.1.7483.2.2.4.8.2.1 |
tnSyncETableTable of Sync-E attributes. SEQUENCE OF TnSyncEntry .1.3.6.1.4.1.7483.2.2.4.8.2.1.1 |
tnSyncEEntry. TnSyncEntry .1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1 |
tnSyncESyncMsgDetermines if the timing reference selection for system timing uses Synchronization Status Message (SSM) Quality Levels or Enhanced Quality Levels.rw NokiaSyncStatusMsgType (TROPIC-TC) .1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.1 |
tnSyncEActiveRefThe ID of the association line reference.ro Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.2 |
tnSyncEWTRThe system timing WTR. Current configurable range: 0 to 12, and 999999.rw Unsigned32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.3 |
tnSyncESwCmdLineRefThe third byte represents the switch command: 1 - nocmd 2 - clear 3 - lockout 4 - forceswitch 5 - mannual 6 - auto 7 - clearlockout. The last byte represents the line reference switch to: 0 - internal 1 - lineref0 2 - lineref1 3 - lineref2 4 - lineref3 5 - lineref4 6 - lineref5.rw Unsigned32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.4 |
tnSyncEClkModStateThe Sync-E clock mode state.ro Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.5 |
tnSyncESystemQLThe value of the system quality level (SSM), shown in following: 31 - not applicable When the NE is in SDH mode: 0 - quality unknown 1 - PRC 2 - SSU_A 3 - SSU_B 4 - SEC 5 - DNU 23 - ePRTC 24 - PRTC 25 - ePRC 26 - eSEC. When the NE is in SONET mode: 11 - PRS 12 - STU 13 - ST2 14 - TNC 15 - ST3E 16 - ST3 17 - SMC 18 - ST4 19 - DUS 20 - PNO 23 - ePRTC 24 - PRTC 25 - ePRC.ro Integer32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.6 |
tnSyncEQLDegradeThresholdThe threshold value of SSM quality level degradation for systme timing reference. When the NE is in SDH mode: 1 - PRC 2 - SSU_A 3 - SSU_B 4 - SEC - Default 23 - ePRTC 24 - PRTC 25 - ePRC 26 - eSEC. When the NE is in SONET mode: 11 - PRS 12 - STU 13 - ST2 14 - TNC 15 - ST3E 16 - ST3 - Default 23 - ePRTC 24 - PRTC 25 - ePRC.rw Integer32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.7 |
tnSyncECurrentActiveLineRefFreqOffThe current frequency offset of the active timing reference.ro Integer32 UNITS "ppb" .1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.8 |
tnSyncEAlmProfName.rw OCTET STRING .1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.9 |
tnSyncELineRefTableTable of VTS map. SEQUENCE OF TnSyncELineRefEntry .1.3.6.1.4.1.7483.2.2.4.8.2.1.2 |
tnSyncELineRefEntry. TnSyncELineRefEntry .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1 |
tnSyncELineRefIndexThe ifIndex of the line reference table. Unsigned32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.1 |
tnSyncELineRefAssignedPortThe assigned port for the line reference.rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.2 |
tnSyncELineRefPriorityLine reference priority. Current configurable range: 0 to 8.rw Unsigned32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.3 |
tnSyncELineRefAdminStateThe administrative state of the line reference.rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.4 |
tnSyncELineRefOperStateThe operating state of the line reference.ro Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.5 |
tnSyncELineLockOutIf lock out line reference or not.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.6 |
tnSyncELineRefStateThe Sync-E line reference state.ro Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.7 |
tnSyncELineRefSwStateThe Sync-E line reference switch state.ro Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.8 |
tnSyncELineRefIncSSMMsgThis object indicates the current value of incoming QL on that port. 30 - unstable 31 - not applicable When the NE works in SDH mode: 0 - Unknown 1 - PRC 2 - SSU_A 3 - SSU_B 4 - SEC 5 - DNU 23 - ePRTC 24 - PRTC 25 - ePRC 26 - eSEC When the NE works in SONET mode: 11 - PRS 12 - STU 13 - ST2 14 - TNC 15 - ST3E 16 - ST3 17 - SMC 18 - ST4 19 - DUS 20 - PNO 23 - ePRTC 24 - PRTC 25 - ePRC It's applicable only to the timing port with SSM capabilities.ro Integer32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.9 |
tnSyncELineRefIncSSMStatusThis object indicates the current status of incoming QL on that port. 0: Valid 1: Invalid 2: Not Supported 3: Not Applicable It's applicable only to the timing port with SSM capabilities.ro Integer32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.10 |
tnSyncELineRefIncSSMSuppEnable or disable the line reference incoming QL processing.rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.11 |
tnSyncELineRefProvQLManually provisioned incoming SSM value for the line reference. The value can be: 0 - AUTO When the NE is in SDH mode: 1 - PRC 2 - SSU_A 3 - SSU_B 4 - SEC 5 - DNU 23 - ePRTC 24 - PRTC 25 - ePRC 26 - eSEC When the NE works in SONET mode: 11 - PRS 12 - STU 13 - ST2 14 - TNC 15 - ST3E 16 - ST3 17 - SMC 18 - ST4 19 - DUS 20 - PNO 23 - ePRTC 24 - PRTC 25 - ePRC Note: The parameter can be provisioned only when SyncELineRefIncSSMSupp is enabled.rw Integer32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.12 |
tnSyncELineRefAssociatedPortThe associated physical port of the line reference. This parameter replaces tnSyncELineRefAssignedPort in order to support assigning a line reference to a port in other slots.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.13 |
tnSyncELineRefPriorityOfStationClockLine reference priority for the output station clock. Current configurable range: 0 to 8.rw Unsigned32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.14 |
tnSyncELineRefLockOutOfStationClockIf lock out the line reference or not for the output station clock.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.15 |
tnSyncELineRefSwStateOfStationClockThe Sync-E line reference switch state of the output station clock.ro Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.16 |
tnSyncELineRefCurrentFreqOffThe current frequency offset of the timing reference.ro Integer32 UNITS "ppb" .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.17 |
tnSyncELineRefAlmProfName.rw OCTET STRING .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.18 |
tnSyncELineRefIncExtdQLTLVClockIDIncoming Extended QL TLV Clock ID.ro AluWdmPtpClockIdentifier (TROPIC-PTP-MIB) .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.19 |
tnSyncELineRefIncExtdQLTLVMixedClockTypeIncoming Extended QL TLV Mixed Clock Type Flag.ro Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.20 |
tnSyncELineRefIncExtdQLTLVPartialChainIncoming Extended QL TLV Partial Chain Flag.ro Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.21 |
tnSyncELineRefIncExtdQLTLVNumeEECIncoming Extended QL TLV Number of eEEC.ro Unsigned32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.22 |
tnSyncELineRefIncExtdQLTLVNumEECIncoming Extended QL TLV Number of EEC.ro Unsigned32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.23 |
tnSyncELineRefProvQLOfStationClockManually provisioned incoming SSM value of the line reference output timing. The value can be: 0 - AUTO When the NE is in SDH mode: 1 - PRC 2 - SSU_A 3 - SSU_B 4 - SEC 5 - DNU 23 - ePRTC 24 - PRTC 25 - ePRC 26 - eSEC When the NE works in SONET mode: 11 - PRS 12 - STU 13 - ST2 14 - TNC 15 - ST3E 16 - ST3 17 - SMC 18 - ST4 19 - DUS 20 - PNO 23 - ePRTC 24 - PRTC 25 - ePRC Note: The parameter can be provisioned only when SyncELineRefIncSSMSupp is enabled.rw Integer32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.24 |
tnSyncELineRefIncSSMMsgOfStationClockThis object indicates the current value of incoming QL for output timing on that port. 30 - unstable 31 - not applicable When the NE works in SDH mode: 0 - Unknown 1 - PRC 2 - SSU_A 3 - SSU_B 4 - SEC 5 - DNU 23 - ePRTC 24 - PRTC 25 - ePRC 26 - eSEC When the NE works in SONET mode: 11 - PRS 12 - STU 13 - ST2 14 - TNC 15 - ST3E 16 - ST3 17 - SMC 18 - ST4 19 - DUS 20 - PNO 23 - ePRTC 24 - PRTC 25 - ePRC It's applicable only to the timing port with SSM capabilities.ro Integer32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.25 |
tnSyncELineRefIncSSMStatusOfStationClockThis object indicates the current status of incoming QL on that port for output timing. 0: Valid 1: Invalid 2: Not Supported 3: Not Applicable It's applicable only to the timing port with SSM capabilities.ro Integer32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.26 |
tnSyncEControlTableTable of Sync-E Control attributes. SEQUENCE OF TnSyncControlEntry .1.3.6.1.4.1.7483.2.2.4.8.2.1.3 |
tnSyncEControlEntry. TnSyncControlEntry .1.3.6.1.4.1.7483.2.2.4.8.2.1.3.1 |
tnSyncEControlEECEnableenable - The Synchronous Ethernet is supported for the pack and the synchronization attributes can be configured. disable - The Synchronous Ethernet is not supported for the pack and the synchronization attributes can not be configured.rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.3.1.1 |
tnSyncEPortTableTable of Sync-E Port attributes. SEQUENCE OF TnSyncPortEntry .1.3.6.1.4.1.7483.2.2.4.8.2.1.4 |
tnSyncEPortEntry. TnSyncPortEntry .1.3.6.1.4.1.7483.2.2.4.8.2.1.4.1 |
tnSyncEOprModeThe port Synchronous Ethernet Operation Mode. When the port is in SYNC mode, recovered clock of its input signal can be selected as a reference clock to the system clock. When the port is in NON-SYNC mode, the recovered clock of its input signal shall not be a candidate to system timing references.rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.4.1.1 |
tnSyncEOutgoingForceSsmTransThe port SSM/Quality Level Transmission value. The value can be: In SDH mode - act, prc, ssua, ssub, sec, dnu, ePRTC, PRTC, ePRC, eSEC, none; In sonet mode - act, stu, prs, st2, sts3e, st3, ePRTC, PRTC, ePRC, dus, none.rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.4.1.2 |
tnSyncEStationClockTableTable of Sync-E station clock attributes. SEQUENCE OF TnSyncEStationClockEntry .1.3.6.1.4.1.7483.2.2.4.8.2.1.5 |
tnSyncEStationClockEntry. TnSyncEStationClockEntry .1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1 |
tnSyncEStationClockSyncMsgDetermines if the timing reference selection for station clock timing uses Synchronization Status Message (SSM) Quality Levels or Enhanced Quality Levels.rw NokiaSyncStatusMsgType (TROPIC-TC) .1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.1 |
tnSyncEStationClockActiveRefThe ID of the association line reference.ro Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.2 |
tnSyncEStationClockWTRThe station clock timing WTR. Current configurable range: 0 to 12, and 999999.rw Unsigned32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.3 |
tnSyncEStationClockSwCmdLineRefThe third byte represents the switch command: 1 - nocmd 2 - clear 3 - lockout 4 - forceswitch 5 - mannual 6 - auto 7 - clearlockout. The last byte represents the line reference switch to: 0 - internal 1 - lineref0 2 - lineref1 3 - lineref2 4 - lineref3 5 - lineref4 6 - lineref5.rw Unsigned32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.4 |
tnSyncEStationClockSystemQLThe value of the system quality level (SSM) for the output timing clock, shown in following: 31 - not applicable When the NE is in SDH mode: 0 - quality unknown 1 - PRC 2 - SSU_A 3 - SSU_B 4 - SEC 5 - DNU 23 - ePRTC 24 - PRTC 25 - ePRC 26 - eSEC. When the NE is in SONET mode: 11 - PRS 12 - STU 13 - ST2 14 - TNC 15 - ST3E 16 - ST3 17 - SMC 18 - ST4 19 - DUS 20 - PNO 23 - ePRTC 24 - PRTC 25 - ePRC.ro Integer32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.5 |
tnSyncEStationClockQLThresholdSpecifies the threshold value for the quality level i.e., SSM value for squelching the output towards timing output. If the quality value of the current selected signal for the output is below the threshold value, the output will be squelched. The squelching can be disabled by means of using the value DNU or DUS. When the NE is in SDH mode: 1 - PRC 2 - SSU_A 3 - SSU_B 4 - SEC 5 - DNU 23 - ePRTC 24 - PRTC 25 - ePRC 26 - eSEC. When the NE is in SONET mode: 11 - PRS 12 - STU 13 - ST2 14 - TNC 15 - ST3E 16 - ST3 17 - SMC 18 - ST4 19 - DUS 23 - ePRTC 24 - PRTC 25 - ePRC. Default value: SEC - for node working in SDH mode ST3 - for node working in SONET moderw Integer32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.6 |
tnSyncEStationClockOutSelSpecifies which signal is selected for the output station clock: OUTTIM - Output is selected from output timing selection process SETG - Output is selected from system internal timing The ID of the association line reference.rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.7 |
tnSyncEStationClockAlmProfName.rw OCTET STRING .1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.8 |
tnSyncEBITSPortTableTable of BITS port attributes. SEQUENCE OF TnSyncEBITSPortEntry .1.3.6.1.4.1.7483.2.2.4.8.2.1.6 |
tnSyncEBITSPortEntry. TnSyncEBITSPortEntry .1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1 |
tnSyncEBITSPortDirectionIndicate the direction of the BITS port.rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.1 |
tnSyncEBITSPortSignalTypeSpecify the signal type for the BITS interface: 0 - 2MHz 1 - unframed E1 2 - framed E1 without SSM 3 - framed E1 with SSM 4 - DS1 SF 5 - DS1 ESF. In SDH mode, 2MHz and E1 signal types are valid and 2MHz is the default value. In SONET mode, only the DS1 signal types are valid and DS1 SF is the default value.rw Integer32 .1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.2 |
tnSyncEBITSPortSaBitSpecifies the Sa bit location used to carry the SSM information. This parameter is only applicable when tnSyncEBITSPortSignalType = 3 (framed E1 with SSM)rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.3 |
tnSyncEBITSPortOutputSSMTransThe port SSM/Quality Level Transmission value. The value can be: In SDH mode - act, prc, ssua, ssub, sec, dnu, none; In sonet mode - act, stu, prs, st2, sts3e, st3, dus, none. Restriction: The parameter is only applicable when tnSyncEBITSPortDirection = output and tnSyncEBITSPortSignalType = 3 (framed E1 with SSM)or 5 (DS1 ESF).rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.4 |
tnSyncEBITSPortOutputAISModeSpecifies which signal is inserted for the timing output port if the output signal is squelched. The parameter is only applicable for output port types supporting SSM. AISMODE - AIS signal is inserted. QLMODE - DUS is inserted as SSM; output is squelched. Restriction: The parameter is only applicable when tnSyncEBITSPortDirection = output and tnSyncEBITSPortSignalType = 3 (framed E1 with SSM) or 5 (DS1 ESF).rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.5 |
tnSyncEBITSPortLineImpedanceNominal line impedance. When in SDH mode, imp75ohms or imp120ohms could be used and the default is imp120ohms. When in ONET mode, imp100ohms could be used and the default is imp100ohms.rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.6 |
tnSyncEBITSPortLineCodeLine code. This attribute is applicable when tnSyncEBITSPortSignalType is DS1 SF or DS1 ESF.rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.7 |
tnSyncEBITSPortLboLine equalization value for the BITS output port, taking one of the following values: - lbo: no compensation - lbo1: 0 to 133 feet - lbo2: 133 to 266 feet - lbo3: 267 to 399 feet - lbo4: 400 to 533 feet - lbo5: 534 to 655 feet This attribute is applicable when tnSyncEBITSPortSignalType is DS1 SF or DS1 ESF.rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.8 |
tnSyncEBITSPortAlmProfNameAlarm profile for BITs portrw OCTET STRING .1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.9 |
tnWanTableTable of Wan attributes. SEQUENCE OF TnWanEntry .1.3.6.1.4.1.7483.2.2.4.8.2.1.7 |
tnWanEntry. TnWanEntry .1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1 |
tnWanAlmProfName.rw OCTET STRING .1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.1 |
tnWanSyncEOprModeThe Synchronous Ethernet Operation Mode. When in SYNC mode, recovered clock of its input signal can be selected as a reference clock to the system clock.When in NON-SYNC mode, the recovered clock of its input signal shall not be a candidate to system timing references.rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.2 |
tnWanSyncEOutgoingForceSsmTransThe port SSM/Quality Level Transmission value. The value can be: In SDH mode - act, prc, ssua, ssub, sec, dnu, ePRTC, PRTC, ePRC, eSEC, none. In SONET mode - act, prs, stu, st2, st3e, st3, ePRTC, PRTC, ePRC, dus, none.rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.3 |
tnWanAdminStatusWan administrative state. It may be used to suppress the alarms or disable consequent actions on the WAN entity.rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.4 |
tnWanOperStatusoperational state of WAN entityro Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.5 |
tnWanStateQualifierIndicates the state qualifier (i.e., the secondary state) of the WAN state.ro TropicStateQualifierType (TROPIC-TC) .1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.6 |
tnWanOperationalCapabilityThe partiallyEnabled(3) state means an abnormal state.ro TropicOperationalCapabilityType (TROPIC-TC) .1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.7 |
tnWanDescriptionWan Description.rw SnmpAdminString .1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.8 |
tnSyncEPacketswitchControlTableTable of Sync-E Control attributes for a packetswitch. This table provides the same functionality as tnSyncEControlTable, but requires a switchid as an index SEQUENCE OF TnSyncPacketswitchControlEntry .1.3.6.1.4.1.7483.2.2.4.8.2.1.8 |
tnSyncEPacketswitchControlEntry. TnSyncPacketswitchControlEntry .1.3.6.1.4.1.7483.2.2.4.8.2.1.8.1 |
tnSyncEPacketswitchControlEECEnableenable - Synchronous Ethernet is supported for the packetswitch and the synchronization attributes can be configured. disable - Synchronous Ethernet is not supported for the packetswitch and the synchronization attributes can not be configured.rw Enumeration .1.3.6.1.4.1.7483.2.2.4.8.2.1.8.1.1 |