TRANGOP5830S-RU-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for TRANGOP5830S-RU-MIB.
78
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
78 total| Object Name |
|---|
trango OBJECT IDENTIFIER .1.3.6.1.4.1.5454 |
RFC1155-SMI Unknown .1.3.6.1.4.1.5454 |
tbw OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1 |
p5830sru OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.24 |
rusys OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.24.1 |
ruversion OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.24.1.1 |
ruversionHWHardware version.ro OCTET STRING .1.3.6.1.4.1.5454.1.24.1.1.1 |
ruversionFWMain firmware version.
Format: <code version>H<hardware version>D<date>.ro DisplayString .1.3.6.1.4.1.5454.1.24.1.1.2 |
ruversionFPGAFPGA firmware version.ro OCTET STRING .1.3.6.1.4.1.5454.1.24.1.1.3 |
ruversionFWChecksumRemote unit firmware checksum.ro OCTET STRING .1.3.6.1.4.1.5454.1.24.1.1.4 |
ruversionFPGAChecksumRemote unit FPGA checksum.ro OCTET STRING .1.3.6.1.4.1.5454.1.24.1.1.5 |
rusysDeviceIdRemote unit device Id. Each remote unit in a cluster shall have unique ID.ro OCTET STRING .1.3.6.1.4.1.5454.1.24.1.2 |
rusysDefOpModeThe operation mode (on or off) the remote unit is on after reboot/power cycle.rw Enumeration .1.3.6.1.4.1.5454.1.24.1.3 |
rusysCurOpModeRemote unit's current operation mode.ro Enumeration .1.3.6.1.4.1.5454.1.24.1.4 |
rusysActivateOpmodeEngage remote unit to on operation mode.rw Enumeration .1.3.6.1.4.1.5454.1.24.1.5 |
rusysReadCommStrSNMP agent read community string. It is used for authenticcation purpose.rw DisplayString .1.3.6.1.4.1.5454.1.24.1.6 |
rusysWriteCommStrSNMP agent write community string. It is used for authentication purpose.rw DisplayString .1.3.6.1.4.1.5454.1.24.1.7 |
ruswitches OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.24.1.8 |
ruswitchesBlockBroadcastMulticastThis switch enables or disables the blocking of Ethernet
control packet except ICMP and ARP to reduce the amount
of uneccessary overhead introduced to the wireless link.rw Enumeration .1.3.6.1.4.1.5454.1.24.1.8.1 |
ruswitchesHTTPDWhen it is turned on, then the remote unit is accessible for
configuring via web browser (e.g. IE or Nescape).rw Enumeration .1.3.6.1.4.1.5454.1.24.1.8.5 |
ruswitchesAutoScanMasterSignalThis switch enables or disables the auto scan master unit
signal operation on the remote unit only.rw Enumeration .1.3.6.1.4.1.5454.1.24.1.8.6 |
rutraffic OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.24.1.9 |
rutrafficEthInOctetsNumber of octets of remote unit's payload received on Ethernet port.ro Counter .1.3.6.1.4.1.5454.1.24.1.9.1 |
rutrafficEthOutOctetsNumber of octets of remote unit's payload transmitted on Ethernet port.ro Counter .1.3.6.1.4.1.5454.1.24.1.9.2 |
rutrafficRfInOctetsNumber of octets of remote unit's payload received from RF port.ro Counter .1.3.6.1.4.1.5454.1.24.1.9.3 |
rutrafficRfOutOctetsNumber of octets of remote unit's payload transmitted to RF port.ro Counter .1.3.6.1.4.1.5454.1.24.1.9.4 |
rusysTemperatureCurrent remote unit temperature value (in Celsius).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.24.1.10 |
rusysUpdateFlashAndActivateSave system setting values to Flash and activate the settings.rw Enumeration .1.3.6.1.4.1.5454.1.24.1.11 |
rusysRebootReboot the remote unit.rw Enumeration .1.3.6.1.4.1.5454.1.24.1.12 |
ruipconfig OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.24.1.13 |
ruipconfigIpAddressNew IP address. It will be saved to
non-volatile memory and activated in 5 secs.rw IpAddress .1.3.6.1.4.1.5454.1.24.1.13.1 |
ruipconfigSubnetNew Subnet mask. It will be saved to
non-volatile memory and activated in 5 secs.rw IpAddress .1.3.6.1.4.1.5454.1.24.1.13.2 |
ruipconfigDefaultGatewayNew Default gateway. It will be saved to
non-volatile memory and activated in 5 secs.rw IpAddress .1.3.6.1.4.1.5454.1.24.1.13.3 |
rurf OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.24.2 |
rurfRSSIRemote unit RSSI (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.24.2.1 |
rurftable OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.24.2.4 |
rurftableChannel1RF channel 1 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.1 |
rurftableChannel2RF channel 2 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.2 |
rurftableChannel3RF channel 3 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.3 |
rurftableChannel4RF channel 4 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.4 |
rurftableChannel5RF channel 5 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.5 |
rurftableChannel6RF channel 6 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.6 |
rurftableChannel7RF channel 7 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.7 |
rurftableChannel8RF channel 8 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.8 |
rurftableChannel9RF channel 9 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.9 |
rurftableChannel10RF channel 10 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.10 |
rurftableChannel11RF channel 11 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.11 |
rurftableChannel12RF channel 12 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.12 |
rurftableChannel13RF channel 13 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.13 |
rurftableChannel14RF channel 14 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.14 |
rurftableChannel15RF channel 15 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.15 |
rurftableChannel16RF channel 16 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.16 |
rurftableChannel17RF channel 17 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.17 |
rurftableChannel18RF channel 18 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.18 |
rurftableChannel19RF channel 19 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.19 |
rurftableChannel20RF channel 20 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.20 |
rurftableChannel21RF channel 21 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.21 |
rurftableChannel22RF channel 22 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.22 |
rurftableChannel23RF channel 23 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.23 |
rurftableChannel24RF channel 24 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.24 |
rurftableChannel25RF channel 25 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.25 |
rurftableChannel26RF channel 26 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.26 |
rurftableChannel27RF channel 27 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.27 |
rurftableChannel28RF channel 28 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.28 |
rurftableChannel29RF channel 29 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.29 |
rurftableChannel30RF channel 30 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the remote unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.24.2.4.30 |
ruism OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.24.2.5 |
ruismTxPowerMaxThe maximum ISM Tx power value can be set (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.24.2.5.1 |
ruismTxPowerMinThe minimum ISM Tx power value can be set (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.24.2.5.2 |
ruismTxPowerISM RF tx power (in dBm). It specifies the power output
of the radio, excluding the antenna gain. Check parameters
remoteismTxPowerMax and remoteismTxPowerMin for power setting range.rw INTEGER (-128..127) .1.3.6.1.4.1.5454.1.24.2.5.3 |
ruismRxThresholdISM RF rx threshold (in dBm). It specifies the receiver
sensitivity of the remote. By default, the radio's sensitivity is -82dBm.
The higher the threshold is, the less sensitive the radio will be.
In M5800S, the value -90 represents the rfrxthreshold is disabled.rw INTEGER (-90 | -85 | -80 | -75 | -70 | -65) .1.3.6.1.4.1.5454.1.24.2.5.4 |
ruunii OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.24.2.6 |
ruuniiTxPowerMaxThis object is only applicable to M5830S/P5830S radio.
The maximum UNII Tx power value can be set (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.24.2.6.1 |
ruuniiTxPowerMinThis object is only applicable to M5830S/P5830S radio.
The minimum UNII Tx power value can be set (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.24.2.6.2 |
ruuniiTxPowerThis object is only applicable to M5830S/P5830S radio.
UNII RF tx power (in dBm). It specifies the power output
of the radio, excluding the antenna gain. Check parameters
apuniiTxPowerMax and apuniiTxPowerMin for power setting range.rw INTEGER (-128..127) .1.3.6.1.4.1.5454.1.24.2.6.3 |
ruuniiRxThresholdThis object is only applicable to M5830S/P5830S radio.
UNII RF rx threshold (in dBm). It specifies the receiver
sensitivity of the master unit.rw INTEGER (-90 | -85 | -80 | -75 | -70 | -65) .1.3.6.1.4.1.5454.1.24.2.6.4 |
mibinfo OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.24.5 |
mibinfoVersionTrango remote unit MIB Version.ro DisplayString .1.3.6.1.4.1.5454.1.24.5.1 |