TRANGOP5830S-MU-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for TRANGOP5830S-MU-MIB.
93
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
93 total| Object Name |
|---|
trango OBJECT IDENTIFIER .1.3.6.1.4.1.5454 |
RFC1155-SMI Unknown .1.3.6.1.4.1.5454 |
tbw OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1 |
p5830smu OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.22 |
musys OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.22.1 |
muversion OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.22.1.1 |
muversionHWHardware version.ro OCTET STRING .1.3.6.1.4.1.5454.1.22.1.1.1 |
muversionFWMain firmware version.
Format: <code version>H<hardware version>D<date>.ro DisplayString .1.3.6.1.4.1.5454.1.22.1.1.2 |
muversionFPGAFPGA firmware version.ro OCTET STRING .1.3.6.1.4.1.5454.1.22.1.1.3 |
muversionFWChecksumMaster unit firmware checksum.ro OCTET STRING .1.3.6.1.4.1.5454.1.22.1.1.4 |
muversionFPGAChecksumMaster unit FPGA checksum.ro OCTET STRING .1.3.6.1.4.1.5454.1.22.1.1.5 |
musysDeviceIdMaster unit device Id. Each master unit in a cluster shall have unique ID.ro OCTET STRING .1.3.6.1.4.1.5454.1.22.1.2 |
musysDefOpModeThe operation mode (on or off) the master unit is on after reboot/power cycle.rw Enumeration .1.3.6.1.4.1.5454.1.22.1.3 |
musysCurOpModeMaster unit's current operation mode.ro Enumeration .1.3.6.1.4.1.5454.1.22.1.4 |
musysActivateOpmodeEngage master unit to on operation mode.rw Enumeration .1.3.6.1.4.1.5454.1.22.1.5 |
musysReadCommStrSNMP agent read community string. It is used for authentication purpose.rw DisplayString .1.3.6.1.4.1.5454.1.22.1.6 |
musysWriteCommStrSNMP agent write community string. It is used for authentication purpose.rw DisplayString .1.3.6.1.4.1.5454.1.22.1.7 |
muswitches OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.22.1.8 |
muswitchesBlockBroadcastMulticastThis switch enables or disables the blocking of Ethernet
control packet except ICMP and ARP to reduce the amount
of uneccessary overhead introduced to the wireless link.rw Enumeration .1.3.6.1.4.1.5454.1.22.1.8.1 |
muswitchesHTTPDWhen it is turned on, then the master unit is accessible
for configuring via web browser (e.g. IE or Nescape).rw Enumeration .1.3.6.1.4.1.5454.1.22.1.8.5 |
muswitchesAutoPowerLevelRemoteUnitWhen it is turned on, then the master unit will
command the remote unit to do power leveling.rw Enumeration .1.3.6.1.4.1.5454.1.22.1.8.7 |
mutraffic OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.22.1.9 |
mutrafficEthInOctetsNumber of payload octets received on Ethernet port.ro Counter .1.3.6.1.4.1.5454.1.22.1.9.1 |
mutrafficEthOutOctetsNumber of payload octets transmitted on Ethernet port.ro Counter .1.3.6.1.4.1.5454.1.22.1.9.2 |
mutrafficRfInOctetsNumber of octets of remote's payload received from RF port.ro Counter .1.3.6.1.4.1.5454.1.22.1.9.3 |
mutrafficRfOutOctetsNumber of octets of remote's payload transmitted to RF port.ro Counter .1.3.6.1.4.1.5454.1.22.1.9.4 |
musysTemperatureCurrent master unit's temperature value (in Celsius).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.22.1.10 |
musysUpdateFlashAndActivateSave system setting values to Flash and activate the settings.rw Enumeration .1.3.6.1.4.1.5454.1.22.1.11 |
musysRebootReboot the master unit.rw Enumeration .1.3.6.1.4.1.5454.1.22.1.12 |
muipconfig OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.22.1.13 |
muipconfigIpAddressNew IP address. It will be saved to
non-volatile memory and activated in 5 secs.rw IpAddress .1.3.6.1.4.1.5454.1.22.1.13.1 |
muipconfigSubnetNew Subnet mask. It will be saved to
non-volatile memory and activated in 5 secs.rw IpAddress .1.3.6.1.4.1.5454.1.22.1.13.2 |
muipconfigDefaultGatewayNew Default gateway. It will be saved to
non-volatile memory and activated in 5 secs.rw IpAddress .1.3.6.1.4.1.5454.1.22.1.13.3 |
murf OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.22.2 |
murfRSSIRemote unit RSSI (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.22.2.1 |
murfActiveChannelIt specifies the current channel number the master unit operates on.rw INTEGER .1.3.6.1.4.1.5454.1.22.2.2 |
murfActivePolarizationIt specifies the current polarization the master unit operates on.rw DisplayString .1.3.6.1.4.1.5454.1.22.2.3 |
murftable OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.22.2.4 |
murftableChannel1RF channel 1 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.1 |
murftableChannel2RF channel 2 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.2 |
murftableChannel3RF channel 3 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.3 |
murftableChannel4RF channel 4 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.4 |
murftableChannel5RF channel 5 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.5 |
murftableChannel6RF channel 6 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.6 |
murftableChannel7RF channel 7 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.7 |
murftableChannel8RF channel 8 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.8 |
murftableChannel9RF channel 9 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.9 |
murftableChannel10RF channel 10 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.10 |
murftableChannel11RF channel 11 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.11 |
murftableChannel12RF channel 12 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.12 |
murftableChannel13RF channel 13 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.13 |
murftableChannel14RF channel 14 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.14 |
murftableChannel15RF channel 15 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.15 |
murftableChannel16RF channel 16 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.16 |
murftableChannel17RF channel 17 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.17 |
murftableChannel18RF channel 18 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.18 |
murftableChannel19RF channel 19 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.19 |
murftableChannel20RF channel 20 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.20 |
murftableChannel21RF channel 21 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.21 |
murftableChannel22RF channel 22 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.22 |
murftableChannel23RF channel 23 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.23 |
murftableChannel24RF channel 24 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.24 |
murftableChannel25RF channel 25 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.25 |
murftableChannel26RF channel 26 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.26 |
murftableChannel27RF channel 27 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.27 |
murftableChannel28RF channel 28 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.28 |
murftableChannel29RF channel 29 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.29 |
murftableChannel30RF channel 30 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the master unit.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.22.2.4.30 |
muism OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.22.2.5 |
muismTxPowerMaxThe maximum ISM Tx power value can be set (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.22.2.5.1 |
muismTxPowerMinThe minimum ISM Tx power value can be set (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.22.2.5.2 |
muismTxPowerISM RF tx power (in dBm). It specifies the power output
of the radio, excluding the antenna gain. Check parameters
muismTxPowerMax and masterismTxPowerMin for power setting range.rw INTEGER (-128..127) .1.3.6.1.4.1.5454.1.22.2.5.3 |
muismRxThresholdISM RF rx threshold (in dBm). It specifies the receiver
sensitivity of the master. By default, the radio's sensitivity is -82dBm.
The higher the threshold is, the less sensitive the radio will be.
In M5800S, the value -90 represents the rfrxthreshold is disabled.rw INTEGER (-90 | -85 | -80 | -75 | -70 | -65) .1.3.6.1.4.1.5454.1.22.2.5.4 |
muismTargetRSSIISM RF RSSI (in dBm). It specifies the target RSSI from the remote unit
to the master unit. Based on this parameter, the master unit can power level
the remote unit so that it receives same level of signal strength from
the remote unit, regardless far or near. Note that when you set the Target RSSI
from the remote unit, you need to consider master unit's RF Rx Threshold value.
The Target RSSI from the remote unit must be 5dB higher than the RF Rx
Threshold. When the RF Rx Threshold is disabled, the setting of the Target
RSSI from remote unit shall be no less than -75dBm.rw INTEGER (-85..-45) .1.3.6.1.4.1.5454.1.22.2.5.5 |
muunii OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.22.2.6 |
muuniiTxPowerMaxThis object is only applicable to M5830S/P5830S radio.
The maximum UNII Tx power value can be set (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.22.2.6.1 |
muuniiTxPowerMinThis object is only applicable to M5830S/P5830S radio.
The minimum UNII Tx power value can be set (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.22.2.6.2 |
muuniiTxPowerThis object is only applicable to M5830S/P5830S radio.
UNII RF tx power (in dBm). It specifies the power output
of the radio, excluding the antenna gain. Check parameters
apuniiTxPowerMax and apuniiTxPowerMin for power setting range.rw INTEGER (-128..127) .1.3.6.1.4.1.5454.1.22.2.6.3 |
muuniiRxThresholdThis object is only applicable to M5830S/P5830S radio.
UNII RF rx threshold (in dBm). It specifies the receiver sensitivity of the master.rw INTEGER (-90 | -85 | -80 | -75 | -70 | -65) .1.3.6.1.4.1.5454.1.22.2.6.4 |
muuniiTargetRSSIThis object is only applicable to M5830S/P5830S radio.
UNII RF target RSSI (in dBm). It specifies the target RSSI from
remote unit to the master unit. Based on this parameter, the master can power
level the remote unit so that it receives same level of signal strength from
the remote unit, regardless far or near. Note that when you set the Target RSSI
from the remote unit, you need to consider remote unit's RF Rx Threshold value.
The Target RSSI from the remote unit must be 5dB higher than the RF Rx Threshold.rw INTEGER (-85..-45) .1.3.6.1.4.1.5454.1.22.2.6.5 |
ru OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.22.3 |
ruDeviceIdRemote unit device ID.rw OCTET STRING .1.3.6.1.4.1.5454.1.22.3.1 |
ruUpstreamMIRIt is the Maximum Information Rate (in Kbps)
the master unit allocates to remote unit.rw INTEGER .1.3.6.1.4.1.5454.1.22.3.2 |
remoteDownstreamMIRIt is the Maximum Information Rate (in Kbps)
the master unit allocates to the remote unit.rw INTEGER .1.3.6.1.4.1.5454.1.22.3.3 |
ruPowerLvlIt is a feature that is typically found in more
elaborate mobile systems such as cellular CDMA
networks. Using this feature, the remote unit have its
RF power output adjusted until its signal strength
received in the master unit is roughly the same.rw Enumeration .1.3.6.1.4.1.5454.1.22.3.4 |
ruRebootMaster unit issues reboot command to remote unit.rw Enumeration .1.3.6.1.4.1.5454.1.22.3.5 |
ruAssociationRemote unit association status.ro Enumeration .1.3.6.1.4.1.5454.1.22.3.6 |
ruDistanceDistance of remote unit (in mile).ro INTEGER .1.3.6.1.4.1.5454.1.22.3.7 |
trapconfig OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.22.4 |
trapconfigDest1IPAddressTrap destination 1 IP address.rw IpAddress .1.3.6.1.4.1.5454.1.22.4.2 |
trapconfigDest2IPAddressTrap destination 2 IP address.rw IpAddress .1.3.6.1.4.1.5454.1.22.4.3 |
mibinfo OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.22.5 |
mibinfoVersionTrango master unit MIB Version.ro DisplayString .1.3.6.1.4.1.5454.1.22.5.1 |