TRANGOM5830S-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for TRANGOM5830S-MIB.
150
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
150 total| Object Name |
|---|
trango OBJECT IDENTIFIER .1.3.6.1.4.1.5454 |
RFC-1215 Unknown .1.3.6.1.4.1.5454 |
tbw OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1 |
m5830sap OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.20 |
apsystem OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.20.1 |
apversion OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.20.1.1 |
apversionHWHardware version.ro OCTET STRING .1.3.6.1.4.1.5454.1.20.1.1.1 |
apversionFWMain firmware version.
Format: <code version>H<hardware version>D<date>.ro DisplayString .1.3.6.1.4.1.5454.1.20.1.1.2 |
apversionFPGAFPGA firmware version.ro OCTET STRING .1.3.6.1.4.1.5454.1.20.1.1.3 |
apversionChecksumAP firmware checksum.ro OCTET STRING .1.3.6.1.4.1.5454.1.20.1.1.4 |
apsystemDeviceIdMAC address.ro OCTET STRING .1.3.6.1.4.1.5454.1.20.1.2 |
apsystemBaseIdCluster that the AP belongs to.
All APs and SUs in the same cluster shall have the same Base ID.rw INTEGER .1.3.6.1.4.1.5454.1.20.1.3 |
apsystemAPIdAP ID. Each AP in a cluster shall have unique AP ID.rw INTEGER .1.3.6.1.4.1.5454.1.20.1.4 |
apsystemDefOpModeThe operation mode (ap or off) the radio is on after reboot/power cycle.rw Enumeration .1.3.6.1.4.1.5454.1.20.1.5 |
apsystemCurOpModeRadio's current operation mode.ro Enumeration .1.3.6.1.4.1.5454.1.20.1.6 |
apsystemActivateOpmodeEngage AP unit to ap operation mode.rw Enumeration .1.3.6.1.4.1.5454.1.20.1.7 |
apsystemIpAddrCurrent IP address.ro IpAddress .1.3.6.1.4.1.5454.1.20.1.8 |
apsystemSubnetCurrent Subnet mask.ro IpAddress .1.3.6.1.4.1.5454.1.20.1.9 |
apsystemDefaultGatewayCurrent Default gateway.ro IpAddress .1.3.6.1.4.1.5454.1.20.1.10 |
apsystemReadCommStrSNMP agent read community string. It is used for authentication purpose.rw DisplayString .1.3.6.1.4.1.5454.1.20.1.11 |
apsystemWriteCommStrSNMP agent write community string. It is used for authentication purpose.rw DisplayString .1.3.6.1.4.1.5454.1.20.1.12 |
apswitches OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.20.1.13 |
apswitchesBlockBroadcastMulticastThis switch enables or disables the blocking of Ethernet
control packet except ICMP and ARP to reduce the amount
of uneccessary overhead introduced to the wireless link.rw Enumeration .1.3.6.1.4.1.5454.1.20.1.13.1 |
apswitchesSUtoSUThis switch enables or disables the peer-to-peer
feature among SUs through the AP. Before this switch
is turned on, all SUs that want to communicate with
each other have to be assigned to the same group.rw Enumeration .1.3.6.1.4.1.5454.1.20.1.13.2 |
apswitchesTFTPDThis switch enables or disables the TFTP operation. When
it is turned on, then the AP will be ready for code download.rw Enumeration .1.3.6.1.4.1.5454.1.20.1.13.4 |
apswitchesHTTPDWhen it is turned on, then the AP is accessible for
configuring via web browser (e.g. IE or Nescape).rw Enumeration .1.3.6.1.4.1.5454.1.20.1.13.5 |
apsystemMIRThresholdMaximum Information Rate (in Kbps), the AP allows the
network to utilize before enforcing CIR on each subscriber.rw Enumeration .1.3.6.1.4.1.5454.1.20.1.14 |
aptraffic OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.20.1.15 |
aptrafficEthRxAvgThroughputLogAverage payload data throughput (in Kbits/sec)
received on Ethernet port over the last 60 seconds.ro INTEGER .1.3.6.1.4.1.5454.1.20.1.15.1 |
aptrafficEthTxAvgThroughputLogAverage payload data throughput (in Kbits/sec)
transmitted on Ethernet port over the last 60 seconds.ro INTEGER .1.3.6.1.4.1.5454.1.20.1.15.2 |
aptrafficRfRxAvgThroughputLogAverage payload data throughput (in Kbits/sec)
received on RF port over the last 60 seconds.ro INTEGER .1.3.6.1.4.1.5454.1.20.1.15.3 |
aptrafficRfTxAvgThroughputLogAverage payload data throughput (in Kbits/sec)
transmitted on RF port over the last 60 seconds.ro INTEGER .1.3.6.1.4.1.5454.1.20.1.15.4 |
aptrafficEthInOctetsNumber of payload octets received on Ethernet port.ro Counter .1.3.6.1.4.1.5454.1.20.1.15.5 |
aptrafficEthOutOctetsNumber of payload octets transmitted on Ethernet port.ro Counter .1.3.6.1.4.1.5454.1.20.1.15.6 |
aptrafficRfInOctetsNumber of octets of SUs payload received from RF port.ro Counter .1.3.6.1.4.1.5454.1.20.1.15.7 |
aptrafficRfOutOctetsNumber of octets of SUs payload transmitted to RF port.ro Counter .1.3.6.1.4.1.5454.1.20.1.15.8 |
apsystemTemperatureCurrent AP temperature value (in Celsius).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.20.1.16 |
apsystemUpdateFlashAndActivateSave system setting values to Flash and activate the settings.rw Enumeration .1.3.6.1.4.1.5454.1.20.1.17 |
apsystemRebootReboot the radio.rw Enumeration .1.3.6.1.4.1.5454.1.20.1.18 |
apipconfig OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.20.1.19 |
apipconfigIpAddressNew IP address. It will be saved to
non-volatile memory and activated in 5 secs.rw IpAddress .1.3.6.1.4.1.5454.1.20.1.19.1 |
apipconfigSubnetNew Subnet mask. It will be saved to
non-volatile memory and activated in 5 secs.rw IpAddress .1.3.6.1.4.1.5454.1.20.1.19.2 |
apipconfigDefaultGatewayNew Default gateway. It will be saved to
non-volatile memory and activated in 5 secs.rw IpAddress .1.3.6.1.4.1.5454.1.20.1.19.3 |
aprf OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.20.2 |
aprfActiveChannelIt specifies the current channel number the radio operates on.rw INTEGER .1.3.6.1.4.1.5454.1.20.2.1 |
aprfActivePolarizationIt specifies the current polarization the radio operates on.rw DisplayString .1.3.6.1.4.1.5454.1.20.2.2 |
aprftable OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.20.2.3 |
aprftableChannel1RF channel 1 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.1 |
aprftableChannel2RF channel 2 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.2 |
aprftableChannel3RF channel 3 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.3 |
aprftableChannel4RF channel 4 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.4 |
aprftableChannel5RF channel 5 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.5 |
aprftableChannel6RF channel 6 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.6 |
aprftableChannel7RF channel 7 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.7 |
aprftableChannel8RF channel 8 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.8 |
aprftableChannel9RF channel 9 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.9 |
aprftableChannel10RF channel 10 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.10 |
aprftableChannel11RF channel 11 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.11 |
aprftableChannel12RF channel 12 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.12 |
aprftableChannel13RF channel 13 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.13 |
aprftableChannel14RF channel 14 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.14 |
aprftableChannel15RF channel 15 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.15 |
aprftableChannel16RF channel 16 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.16 |
aprftableChannel17RF channel 17 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.17 |
aprftableChannel18RF channel 18 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.18 |
aprftableChannel19RF channel 19 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.19 |
aprftableChannel20RF channel 20 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.20 |
aprftableChannel21RF channel 21 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.21 |
aprftableChannel22RF channel 22 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.22 |
aprftableChannel23RF channel 23 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.23 |
aprftableChannel24RF channel 24 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.24 |
aprftableChannel25RF channel 25 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.25 |
aprftableChannel26RF channel 26 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.26 |
aprftableChannel27RF channel 27 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.27 |
aprftableChannel28RF channel 28 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.28 |
aprftableChannel29RF channel 29 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.29 |
aprftableChannel30RF channel 30 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.20.2.3.30 |
apism OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.20.2.4 |
apismTxPowerMaxThe maximum ISM Tx power value can be set (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.20.2.4.1 |
apismTxPowerMinThe minimum ISM Tx power value can be set (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.20.2.4.2 |
apismTxPowerISM RF tx power (in dBm). It specifies the power output
of the radio, excluding the antenna gain. Check parameters
apismTxPowerMax and apismTxPowerMin for power setting range.rw INTEGER (-128..127) .1.3.6.1.4.1.5454.1.20.2.4.3 |
apismServiceRadiusISM RF service radius (in mile). It specifies the distance of
the furthest SU the AP will serve. Based on this information,
the AP will determine the maximum wait time for a SU to
response to a poll before it starts to poll the next one.rw Enumeration .1.3.6.1.4.1.5454.1.20.2.4.4 |
apismRxThresholdISM RF rx threshold (in dBm). It specifies the receiver sensitivity
of the AP. By default, the radio's sensitivity is -82dBm.
The higher the threshold is, the less sensitive the radio will be.
In M5800S, the value -90 represents the rfrxthreshold is disabled.rw INTEGER (-90 | -85 | -80 | -75 | -70 | -65) .1.3.6.1.4.1.5454.1.20.2.4.5 |
apismTargetRSSIISM RF target RSSI (in dBm). It specifies the target RSSI from all SUs to
the AP. Based on this parameter, the AP can power level each SU
so that it receives same level of signal strength from all SUs,
regardless far or near. Note that when you set the Target RSSI
from SU, you need to consider AP's RF Rx Threshold value.
The Target RSSI from SU must be 5dB higher than the RF Rx Threshold.
When the RF Rx Threshold is disabled, the setting of the Target RSSI
from SU shall be no less than -75dBm.rw INTEGER (-85..-45) .1.3.6.1.4.1.5454.1.20.2.4.6 |
apunii OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.20.2.5 |
apuniiTxPowerMaxThis object is only applicable to M5830S radio.
The maximum UNII Tx power value can be set (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.20.2.5.1 |
apuniiTxPowerMinThis object is only applicable to M5830S radio.
The minimum UNII Tx power value can be set (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.20.2.5.2 |
apuniiTxPowerThis object is only applicable to M5830S radio.
UNII RF tx power (in dBm). It specifies the power output
of the radio, excluding the antenna gain. Check parameters
apuniiTxPowerMax and apuniiTxPowerMin for power setting range.rw INTEGER (-128..127) .1.3.6.1.4.1.5454.1.20.2.5.3 |
apuniiServiceRadiusThis object is only applicable to M5830S radio.
UNII RF service radius (in mile). It specifies the distance of
the furthest SU the AP will serve. Based on this information,
the AP will determine the maximum wait time for a SU to
response to a poll before it starts to poll the next one.rw Enumeration .1.3.6.1.4.1.5454.1.20.2.5.4 |
apuniiRxThresholdThis object is only applicable to M5830S radio.
UNII RF rx threshold (in dBm). It specifies the receiver sensitivity of the AP.rw INTEGER (-90 | -85 | -80 | -75 | -70 | -65) .1.3.6.1.4.1.5454.1.20.2.5.5 |
apuniiTargetRSSIThis object is only applicable to M5830S radio.
UNII RF target RSSI (in dBm). It specifies the target RSSI from all SUs to
the AP. Based on this parameter, the AP can power level each SU so that
it receives same level of signal strength from all SUs, regardless far
or near. Note that when you set the Target RSSI from SU, you need to
consider AP's RF Rx Threshold value. The Target RSSI from SU must be 5dB
higher than the RF Rx Threshold.rw INTEGER (-85..-45) .1.3.6.1.4.1.5454.1.20.2.5.6 |
su OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.20.3 |
suSUCountNumber of subscriber units in the subscriber database.ro INTEGER .1.3.6.1.4.1.5454.1.20.3.1 |
suPowerLvlAllIt is a feature that is typically found in more
elaborate mobile systems such as cellular CDMA
networks. Using this feature, all SUs have their
RF power output adjusted until the signal strength
for each SU as received in the AP is roughly the same.rw Enumeration .1.3.6.1.4.1.5454.1.20.3.2 |
suStatisticsSamplePeriodA period (in minute) AP requests update on SU Info Table from all associated SUs.rw INTEGER .1.3.6.1.4.1.5454.1.20.3.3 |
suRebootAllAP broadcasts reboot command to all subscriber units.rw Enumeration .1.3.6.1.4.1.5454.1.20.3.4 |
sudb OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.20.3.5 |
sudbDeleteOrAddIDSubscriber unit ID (1..8190). Each
subscriber in a sector shall have a unique ID.rw INTEGER .1.3.6.1.4.1.5454.1.20.3.5.1 |
sudbAddMACIt is the MAC address of the subscriber unit,
which can be found on the back of the SU.rw OCTET STRING .1.3.6.1.4.1.5454.1.20.3.5.2 |
sudbAddPollingIt is service level value, regular or priority, of a SU.
The AP will poll priority user more often, thus better
network latency as the result. As the network latency
varies based on the number of subscriber units the AP
serves, priority user is guaranteed that the latency is
NOT greater than 100ms regardless of the size of the network.rw Enumeration .1.3.6.1.4.1.5454.1.20.3.5.3 |
sudbAddSUtoSUIt is peer-to-peer group this SU belongs to.
With the SU to SU switch is turned on, SUs in
the same peer-to-peer group can communicate to
each other via the AP. There are totally 15 groups
available. Note that the SU shall be set to priority
user for this feature to improve latency.rw Enumeration .1.3.6.1.4.1.5454.1.20.3.5.4 |
sudbAddCIRIt is the Committed Information Rate (in Kbps) the AP allocates to SU.rw INTEGER .1.3.6.1.4.1.5454.1.20.3.5.5 |
sudbAddMIRIt is the Maximum Information Rate (in Kbps) the AP allocates to SU.rw INTEGER .1.3.6.1.4.1.5454.1.20.3.5.6 |
sudbAddAdd a subscriber (specified in object sudbDeleteOrAddID) to the subscriber database.rw Enumeration .1.3.6.1.4.1.5454.1.20.3.5.7 |
sudbDeleteDelete a subscriber (specified in object sudbDeleteOrAddID) from the subscriber database.rw Enumeration .1.3.6.1.4.1.5454.1.20.3.5.8 |
suInfoTableA table that contains subscriber unit entities. SEQUENCE OF SuInfoEntry .1.3.6.1.4.1.5454.1.20.3.6 |
suInfoEntryInformation about a specific subscriber unit retrieved by its ID number. SuInfoEntry .1.3.6.1.4.1.5454.1.20.3.6.1 |
suIDSubscriber unit ID. Each subscriber in a sector shall have a unique ID.ro INTEGER .1.3.6.1.4.1.5454.1.20.3.6.1.1 |
suMACSubscriber unit MAC Address. Format: 00 01 DE xx xx xx.ro OCTET STRING .1.3.6.1.4.1.5454.1.20.3.6.1.2 |
suPollingIt is service level value, regular or priority, of a SU.
The AP will poll priority user more often, thus better
network latency as the result. As the network latency
varies based on the number of subscriber units the AP
serves, priority user is guaranteed that the latency is
NOT greater than 100ms regardless of the size of the network.ro Enumeration .1.3.6.1.4.1.5454.1.20.3.6.1.3 |
suSUtoSUIt is peer-to-peer group this SU belongs to.
With the SU to SU switch is turned on, SUs in
the same peer-to-peer group can communicate to
each other via the AP. There are totally 15 groups
available. Note that the SU shall be set to priority
user for this feature to improve latency.ro Enumeration .1.3.6.1.4.1.5454.1.20.3.6.1.4 |
suCIRIt is the Committed Information Rate (in Kbps) the AP allocates to SU.ro INTEGER .1.3.6.1.4.1.5454.1.20.3.6.1.5 |
suMIRIt is the Maximum Information Rate (in Kbps) the AP allocates to SU.ro INTEGER .1.3.6.1.4.1.5454.1.20.3.6.1.6 |
suIPAddrSubscriber unit IP Address.ro IpAddress .1.3.6.1.4.1.5454.1.20.3.6.1.7 |
suRemarksSubscriber unit Remark.ro DisplayString .1.3.6.1.4.1.5454.1.20.3.6.1.8 |
suHWVerSubscriber unit Hardware Version.ro OCTET STRING .1.3.6.1.4.1.5454.1.20.3.6.1.9 |
suFWVerSubscriber unit main firmware version.ro DisplayString .1.3.6.1.4.1.5454.1.20.3.6.1.10 |
suFPGAVerSubscriber unit FPGA firmware version.ro OCTET STRING .1.3.6.1.4.1.5454.1.20.3.6.1.11 |
suChecksumSubscriber unit firmware checksum.ro OCTET STRING .1.3.6.1.4.1.5454.1.20.3.6.1.12 |
suAssociationSubscriber unit association status.ro Enumeration .1.3.6.1.4.1.5454.1.20.3.6.1.13 |
suDIstanceDistance of SU (in mile).ro INTEGER .1.3.6.1.4.1.5454.1.20.3.6.1.14 |
suRSSIFromSUSubscriber unit RSSI from SU (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.20.3.6.1.15 |
suRSSIFromAPSubscriber unit RSSI from AP (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.20.3.6.1.16 |
suTxPowerSubscriber unit Tx Power Level (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.20.3.6.1.17 |
suEthRxAvgThroughputLogAverage payload data throughput (in Kbits/sec) received on the
Ethernet port over the period specified by suStatisticsSamplePeriod.ro INTEGER .1.3.6.1.4.1.5454.1.20.3.6.1.18 |
suEthTxAvgThroughputLogAverage payload data throughput (in Kbits/sec) transmitted on the
Ethernet port over the period specified by suStatisticsSamplePeriod.ro INTEGER .1.3.6.1.4.1.5454.1.20.3.6.1.19 |
suRfRxAvgThroughputLogAverage payload data throughput (in Kbits/sec) received on the
RF port over the period specified by suStatisticsSamplePeriod.ro INTEGER .1.3.6.1.4.1.5454.1.20.3.6.1.20 |
suRfTxAvgThroughputLogAverage payload data throughput (in Kbits/sec) transmitted on the
RF port over the period specified by suStatisticsSamplePeriod.ro INTEGER .1.3.6.1.4.1.5454.1.20.3.6.1.21 |
suRfInOctetsNumber of payload octets received on the RF port.ro Counter .1.3.6.1.4.1.5454.1.20.3.6.1.22 |
suRfOutOctetsNumber of payload octets transmitted on the RF port.ro Counter .1.3.6.1.4.1.5454.1.20.3.6.1.23 |
suPowerLevelIt is a feature that is typically found in more
elaborate mobile systems such as cellular CDMA
networks. Using this feature, the SU has its
RF power output adjusted until its signal strength
received in the AP is roughly the same.rw Enumeration .1.3.6.1.4.1.5454.1.20.3.6.1.24 |
suTemperatureSubscriber Unit temperature reading value (in Celsius).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.20.3.6.1.25 |
suRebootAP issues reboot command to a specific subscriber unit.rw Enumeration .1.3.6.1.4.1.5454.1.20.3.6.1.26 |
suTCPIPForLocalEthWhen it is turned on, then the SU will process all the local TCP/IP service.rw Enumeration .1.3.6.1.4.1.5454.1.20.3.6.1.27 |
trapconfig OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.20.4 |
trapconfigTrapCountTypes of trap.ro INTEGER .1.3.6.1.4.1.5454.1.20.4.1 |
trapconfigDest1IPAddressTrap destination 1 IP address.rw IpAddress .1.3.6.1.4.1.5454.1.20.4.2 |
trapconfigDest2IPAddressTrap destination 2 IP address.rw IpAddress .1.3.6.1.4.1.5454.1.20.4.3 |
trapconfigTrapTableA table that contains information of Trango trap events . SEQUENCE OF TrapconfigTrapEntry .1.3.6.1.4.1.5454.1.20.4.4 |
trapconfigTrapEntryInformation about a specific Trango trap event. TrapconfigTrapEntry .1.3.6.1.4.1.5454.1.20.4.4.1 |
aptrpIndexTrap index.ro INTEGER .1.3.6.1.4.1.5454.1.20.4.4.1.1 |
aptrpIDSpecific trap ID.ro INTEGER .1.3.6.1.4.1.5454.1.20.4.4.1.2 |
aptrpCommStrSpecific trap community string.rw DisplayString .1.3.6.1.4.1.5454.1.20.4.4.1.3 |
aptrpEnableEnable a specific Trango trap event or not.rw Enumeration .1.3.6.1.4.1.5454.1.20.4.4.1.4 |
mibinfo OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.20.5 |
mibinfoVersionTrango MIB Version.ro DisplayString .1.3.6.1.4.1.5454.1.20.5.1 |
m5830straps OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.20.16 |
suLinkUpThe SNMP trap that is generated when a specific SU Associated. TRAP-TYPE .1.3.6.1.4.1.5454.1.20.16.0.7 |
suLinkDownThe SNMP trap that is generated when a specific SU Powered Off. TRAP-TYPE .1.3.6.1.4.1.5454.1.20.16.0.8 |
apOpModeFailureThe SNMP trap that is generated when a specific AP
not being in ap mode during boot up sequence. TRAP-TYPE .1.3.6.1.4.1.5454.1.20.16.0.9 |