TRANGOM5800S-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for TRANGOM5800S-MIB.
145
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
145 total| Object Name |
|---|
trango OBJECT IDENTIFIER .1.3.6.1.4.1.5454 |
RFC-1215 Unknown .1.3.6.1.4.1.5454 |
tbw OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1 |
m5800sap OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.10 |
apsystem OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.10.1 |
apversion OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.10.1.1 |
apsysHWHardware version.ro OCTET STRING .1.3.6.1.4.1.5454.1.10.1.1.1 |
apsysFWMain firmware version.
Format: <code version>H<hardware version>D<date>.ro DisplayString .1.3.6.1.4.1.5454.1.10.1.1.2 |
apsysFPGAFPGA firmware version.ro OCTET STRING .1.3.6.1.4.1.5454.1.10.1.1.3 |
apsysChecksumAP firmware checksum.ro OCTET STRING .1.3.6.1.4.1.5454.1.10.1.1.4 |
apsysDeviceIdMAC address.ro OCTET STRING .1.3.6.1.4.1.5454.1.10.1.2 |
apsysBaseIdCluster that the AP belongs to.
All APs and SUs in the same cluster shall have the same Base ID.rw INTEGER .1.3.6.1.4.1.5454.1.10.1.3 |
apsysAPIdAP ID. Each AP in a cluster shall have unique AP ID.rw INTEGER .1.3.6.1.4.1.5454.1.10.1.4 |
apsysDefOpModeThe operation mode (ap or off) the radio is on after reboot/power cycle.rw Enumeration .1.3.6.1.4.1.5454.1.10.1.5 |
apsysCurOpModeRadio's current operation mode.ro Enumeration .1.3.6.1.4.1.5454.1.10.1.6 |
apsysActivateOpmodeEngage AP unit to ap operation mode.rw Enumeration .1.3.6.1.4.1.5454.1.10.1.7 |
apsysIPAddrIP address.rw IpAddress .1.3.6.1.4.1.5454.1.10.1.8 |
apsysSubnetSubnet mask.rw IpAddress .1.3.6.1.4.1.5454.1.10.1.9 |
apsysDefaultGatewayDefault gateway.rw IpAddress .1.3.6.1.4.1.5454.1.10.1.10 |
apsysReadCommStrSNMP agent read community string. It is used for authentication purpose.rw DisplayString .1.3.6.1.4.1.5454.1.10.1.11 |
apsysWriteCommStrSNMP agent write community string. It is used for authentication purpose.rw DisplayString .1.3.6.1.4.1.5454.1.10.1.12 |
apswitches OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.10.1.13 |
apsysBlockBroadcastMulticastThis switch enables or disables the blocking of Ethernet
control packet except ICMP and ARP to reduce the amount
of uneccessary overhead introduced to the wireless link.rw Enumeration .1.3.6.1.4.1.5454.1.10.1.13.1 |
apsysSUtoSUThis switch enables or disables the peer-to-peer
feature among SUs through the AP. Before this switch
is turned on, all SUs that want to communicate with
each other have to be assigned to the same group.rw Enumeration .1.3.6.1.4.1.5454.1.10.1.13.2 |
apsysTFTPDThis switch enables or disables the TFTP operation. When
it is turned on, then the AP will be ready for code download.rw Enumeration .1.3.6.1.4.1.5454.1.10.1.13.4 |
apsysHTTPDWhen it is turned on, then the AP is accessible for
configuring via web browser (e.g. IE or Nescape).rw Enumeration .1.3.6.1.4.1.5454.1.10.1.13.5 |
apsysMIRThresholdMaximum Information Rate (in Kbps), the AP allows the
network to utilize before enforcing CIR on each subscriber.rw Enumeration .1.3.6.1.4.1.5454.1.10.1.14 |
aptraffic OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.10.1.15 |
apsysEthRxAvgThroughputLogAverage payload data throughput (in Kbits/sec)
received on Ethernet port over the last 60 seconds.ro INTEGER .1.3.6.1.4.1.5454.1.10.1.15.1 |
apsysEthTxAvgThroughputLogAverage payload data throughput (in Kbits/sec)
transmitted on Ethernet port over the last 60 seconds.ro INTEGER .1.3.6.1.4.1.5454.1.10.1.15.2 |
apsysRfRxAvgThroughputLogAverage payload data throughput (in Kbits/sec)
received on RF port over the last 60 seconds.ro INTEGER .1.3.6.1.4.1.5454.1.10.1.15.3 |
apsysRfTxAvgThroughputLogAverage payload data throughput (in Kbits/sec)
transmitted on RF port over the last 60 seconds.ro INTEGER .1.3.6.1.4.1.5454.1.10.1.15.4 |
apsysEthInOctetsNumber of payload octets received on Ethernet port.ro Counter .1.3.6.1.4.1.5454.1.10.1.15.5 |
apsysEthOutOctetsNumber of payload octets transmitted on Ethernet port.ro Counter .1.3.6.1.4.1.5454.1.10.1.15.6 |
apsysRfInOctetsNumber of octets of SUs payload received from RF port.ro Counter .1.3.6.1.4.1.5454.1.10.1.15.7 |
apsysRfOutOctetsNumber of octets of SUs payload transmitted to RF port.ro Counter .1.3.6.1.4.1.5454.1.10.1.15.8 |
apsysTemperatureCurrent AP temperature value (in Celsius).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.10.1.16 |
apsysUpdateFlashAndActivateSave system setting values to Flash and activate the settings.rw Enumeration .1.3.6.1.4.1.5454.1.10.1.17 |
apsysRebootReboot the radio.rw Enumeration .1.3.6.1.4.1.5454.1.10.1.18 |
aprf OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.10.2 |
aprfActiveChannelIt specifies the current channel number the radio operates on.rw INTEGER .1.3.6.1.4.1.5454.1.10.2.1 |
aprfActivePolarizationIt specifies the current polarization the radio operates on.rw DisplayString .1.3.6.1.4.1.5454.1.10.2.2 |
aprftable OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.10.2.3 |
aprfChannel1RF channel 1 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.1 |
aprfChannel2RF channel 2 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.2 |
aprfChannel3RF channel 3 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.3 |
aprfChannel4RF channel 4 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.4 |
aprfChannel5RF channel 5 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.5 |
aprfChannel6RF channel 6 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.6 |
aprfChannel7RF channel 7 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.7 |
aprfChannel8RF channel 8 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.8 |
aprfChannel9RF channel 9 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.9 |
aprfChannel10RF channel 10 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.10 |
aprfChannel11RF channel 11 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.11 |
aprfChannel12RF channel 12 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.12 |
aprfChannel13RF channel 13 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.13 |
aprfChannel14RF channel 14 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.14 |
aprfChannel15RF channel 15 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.15 |
aprfChannel16RF channel 16 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.16 |
aprfChannel17RF channel 17 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.17 |
aprfChannel18RF channel 18 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.18 |
aprfChannel19RF channel 19 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.19 |
aprfChannel20RF channel 20 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.20 |
aprfChannel21RF channel 21 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.21 |
aprfChannel22RF channel 22 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.22 |
aprfChannel23RF channel 23 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.23 |
aprfChannel24RF channel 24 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.24 |
aprfChannel25RF channel 25 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.25 |
aprfChannel26RF channel 26 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.26 |
aprfChannel27RF channel 27 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.27 |
aprfChannel28RF channel 28 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.28 |
aprfChannel29RF channel 29 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.29 |
aprfChannel30RF channel 30 frequency (in MHz). It allows you to create your
own channel instead of the manufacturing defaults in the AP.
Keep in mind that channel width is 20MHz, and the frequency
specified here is the center frequency.
Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.rw INTEGER (5260..5340 | 5736..5836) .1.3.6.1.4.1.5454.1.10.2.3.30 |
apism OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.10.2.4 |
aprfismTxPowerMaxThe maximum ISM Tx power value can be set (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.10.2.4.1 |
aprfismTxPowerMinThe minimum ISM Tx power value can be set (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.10.2.4.2 |
aprfismTxPowerISM RF tx power (in dBm). It specifies the power output
of the radio, excluding the antenna gain. Check parameters
aprfismTxPowerMax and aprfismTxPowerMin for power setting range.rw INTEGER (-128..127) .1.3.6.1.4.1.5454.1.10.2.4.3 |
aprfismServiceRadiusISM RF service radius (in mile). It specifies the distance of
the furthest SU the AP will serve. Based on this information,
the AP will determine the maximum wait time for a SU to
response to a poll before it starts to poll the next one.rw Enumeration .1.3.6.1.4.1.5454.1.10.2.4.4 |
aprfismRxThresholdISM RF rx threshold (in dBm). It specifies the receiver sensitivity
of the AP. By default, the radio's sensitivity is -82dBm.
The higher the threshold is, the less sensitive the radio will be.
In M5800S, the value -90 represents the rfrxthreshold is disabled.rw INTEGER (-90 | -85 | -80 | -75 | -70 | -65) .1.3.6.1.4.1.5454.1.10.2.4.5 |
aprfismTargetRSSIISM RF target RSSI (in dBm). It specifies the target RSSI from all SUs to
the AP. Based on this parameter, the AP can power level each SU
so that it receives same level of signal strength from all SUs,
regardless far or near. Note that when you set the Target RSSI
from SU, you need to consider AP's RF Rx Threshold value.
The Target RSSI from SU must be 5dB higher than the RF Rx Threshold.
When the RF Rx Threshold is disabled, the setting of the Target RSSI
from SU shall be no less than -75dBm.rw INTEGER (-85..-45) .1.3.6.1.4.1.5454.1.10.2.4.6 |
apunii OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.10.2.5 |
aprfuniiTxPowerMaxThis object is only applicable to M5830S radio.
The maximum UNII Tx power value can be set (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.10.2.5.1 |
aprfuniiTxPowerMinThis object is only applicable to M5830S radio.
The minimum UNII Tx power value can be set (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.10.2.5.2 |
aprfuniiTxPowerThis object is only applicable to M5830S radio.
UNII RF tx power (in dBm). It specifies the power output
of the radio, excluding the antenna gain. Check parameters
aprfuniiTxPowerMax and aprfuniiTxPowerMin for power setting range.rw INTEGER (-128..127) .1.3.6.1.4.1.5454.1.10.2.5.3 |
aprfuniiServiceRadiusThis object is only applicable to M5830S radio.
UNII RF service radius (in mile). It specifies the distance of
the furthest SU the AP will serve. Based on this information,
the AP will determine the maximum wait time for a SU to
response to a poll before it starts to poll the next one.rw Enumeration .1.3.6.1.4.1.5454.1.10.2.5.4 |
aprfuniiRxThresholdThis object is only applicable to M5830S radio.
UNII RF rx threshold (in dBm). It specifies the receiver sensitivity of the AP.rw INTEGER (-90 | -85 | -80 | -75 | -70 | -65) .1.3.6.1.4.1.5454.1.10.2.5.5 |
aprfuniiTargetRSSIThis object is only applicable to M5830S radio.
UNII RF target RSSI (in dBm). It specifies the target RSSI from all SUs to
the AP. Based on this parameter, the AP can power level each SU so that
it receives same level of signal strength from all SUs, regardless far
or near. Note that when you set the Target RSSI from SU, you need to
consider AP's RF Rx Threshold value. The Target RSSI from SU must be 5dB
higher than the RF Rx Threshold.rw INTEGER (-85..-45) .1.3.6.1.4.1.5454.1.10.2.5.6 |
su OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.10.3 |
suSUCountNumber of subscriber units in the subscriber database.ro INTEGER .1.3.6.1.4.1.5454.1.10.3.1 |
suPowerLvlAllIt is a feature that is typically found in more
elaborate mobile systems such as cellular CDMA
networks. Using this feature, all SUs have their
RF power output adjusted until the signal strength
for each SU as received in the AP is roughly the same.rw Enumeration .1.3.6.1.4.1.5454.1.10.3.2 |
suStatisticsSamplePeriodA period (in minute) AP requests update on SU Info Table from all associated SUs.rw INTEGER .1.3.6.1.4.1.5454.1.10.3.3 |
suRebootAllAP broadcasts reboot command to all subscriber units.rw Enumeration .1.3.6.1.4.1.5454.1.10.3.4 |
sudb OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.10.3.5 |
suAddOrDeleteIDSubscriber unit ID (1..8190). Each
subscriber in a sector shall have a unique ID.rw INTEGER .1.3.6.1.4.1.5454.1.10.3.5.1 |
suAddMACIt is the MAC address of the subscriber unit,
which can be found on the back of the SU.rw OCTET STRING .1.3.6.1.4.1.5454.1.10.3.5.2 |
suAddPollingIt is service level value, regular or priority, of a SU.
The AP will poll priority user more often, thus better
network latency as the result. As the network latency
varies based on the number of subscriber units the AP
serves, priority user is guaranteed that the latency is
NOT greater than 100ms regardless of the size of the network.rw Enumeration .1.3.6.1.4.1.5454.1.10.3.5.3 |
suAddSUtoSUIt is peer-to-peer group this SU belongs to.
With the SU to SU switch is turned on, SUs in
the same peer-to-peer group can communicate to
each other via the AP. There are totally 15 groups
available. Note that the SU shall be set to priority
user for this feature to improve latency.rw Enumeration .1.3.6.1.4.1.5454.1.10.3.5.4 |
suAddCIRIt is the Committed Information Rate (in Kbps) the AP allocates to SU.rw INTEGER .1.3.6.1.4.1.5454.1.10.3.5.5 |
suAddMIRIt is the Maximum Information Rate (in Kbps) the AP allocates to SU.rw INTEGER .1.3.6.1.4.1.5454.1.10.3.5.6 |
suAddAdd a subscriber (specified in object suAddOrDeleteID) to the subscriber database.rw Enumeration .1.3.6.1.4.1.5454.1.10.3.5.7 |
suDeleteDelete a subscriber (specified in object suAddOrDeleteID) from the subscriber database.rw Enumeration .1.3.6.1.4.1.5454.1.10.3.5.8 |
suInfoTableA table that contains subscriber unit entities. SEQUENCE OF SuInfoEntry .1.3.6.1.4.1.5454.1.10.3.6 |
suInfoEntryInformation about a specific subscriber unit retrieved by its ID number. SuInfoEntry .1.3.6.1.4.1.5454.1.10.3.6.1 |
suIDSubscriber unit ID. Each subscriber in a sector shall have a unique ID.ro INTEGER .1.3.6.1.4.1.5454.1.10.3.6.1.1 |
suMACSubscriber unit MAC Address. Format: 00 01 DE xx xx xx.ro OCTET STRING .1.3.6.1.4.1.5454.1.10.3.6.1.2 |
suPollingIt is service level value, regular or priority, of a SU.
The AP will poll priority user more often, thus better
network latency as the result. As the network latency
varies based on the number of subscriber units the AP
serves, priority user is guaranteed that the latency is
NOT greater than 100ms regardless of the size of the network.ro Enumeration .1.3.6.1.4.1.5454.1.10.3.6.1.3 |
suSUtoSUIt is peer-to-peer group this SU belongs to.
With the SU to SU switch is turned on, SUs in
the same peer-to-peer group can communicate to
each other via the AP. There are totally 15 groups
available. Note that the SU shall be set to priority
user for this feature to improve latency.ro Enumeration .1.3.6.1.4.1.5454.1.10.3.6.1.4 |
suCIRIt is the Committed Information Rate (in Kbps) the AP allocates to SU.ro INTEGER .1.3.6.1.4.1.5454.1.10.3.6.1.5 |
suMIRIt is the Maximum Information Rate (in Kbps) the AP allocates to SU.ro INTEGER .1.3.6.1.4.1.5454.1.10.3.6.1.6 |
suIPAddrSubscriber unit IP Address.ro IpAddress .1.3.6.1.4.1.5454.1.10.3.6.1.7 |
suRemarksSubscriber unit Remark.ro DisplayString .1.3.6.1.4.1.5454.1.10.3.6.1.8 |
suHWVerSubscriber unit Hardware Version.ro OCTET STRING .1.3.6.1.4.1.5454.1.10.3.6.1.9 |
suFWVerSubscriber unit main firmware version.ro DisplayString .1.3.6.1.4.1.5454.1.10.3.6.1.10 |
suFPGAVerSubscriber unit FPGA firmware version.ro OCTET STRING .1.3.6.1.4.1.5454.1.10.3.6.1.11 |
suChecksumSubscriber unit firmware checksum.ro OCTET STRING .1.3.6.1.4.1.5454.1.10.3.6.1.12 |
suAssociationSubscriber unit association status.ro Enumeration .1.3.6.1.4.1.5454.1.10.3.6.1.13 |
suDIstanceDistance of SU (in mile).ro INTEGER .1.3.6.1.4.1.5454.1.10.3.6.1.14 |
suRSSIFromSUSubscriber unit RSSI from SU (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.10.3.6.1.15 |
suRSSIFromAPSubscriber unit RSSI from AP (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.10.3.6.1.16 |
suTxPowerSubscriber unit Tx Power Level (in dBm).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.10.3.6.1.17 |
suEthRxAvgThroughputLogAverage payload data throughput (in Kbits/sec) received on the
Ethernet port over the period specified by suStatisticsSamplePeriod.ro INTEGER .1.3.6.1.4.1.5454.1.10.3.6.1.18 |
suEthTxAvgThroughputLogAverage payload data throughput (in Kbits/sec) transmitted on the
Ethernet port over the period specified by suStatisticsSamplePeriod.ro INTEGER .1.3.6.1.4.1.5454.1.10.3.6.1.19 |
suRfRxAvgThroughputLogAverage payload data throughput (in Kbits/sec) received on the
RF port over the period specified by suStatisticsSamplePeriod.ro INTEGER .1.3.6.1.4.1.5454.1.10.3.6.1.20 |
suRfTxAvgThroughputLogAverage payload data throughput (in Kbits/sec) transmitted on the
RF port over the period specified by suStatisticsSamplePeriod.ro INTEGER .1.3.6.1.4.1.5454.1.10.3.6.1.21 |
suRfInOctetsNumber of payload octets received on the RF port.ro Counter .1.3.6.1.4.1.5454.1.10.3.6.1.22 |
suRfOutOctetsNumber of payload octets transmitted on the RF port.ro Counter .1.3.6.1.4.1.5454.1.10.3.6.1.23 |
suPowerLevelIt is a feature that is typically found in more
elaborate mobile systems such as cellular CDMA
networks. Using this feature, the SU has its
RF power output adjusted until its signal strength
received in the AP is roughly the same.rw Enumeration .1.3.6.1.4.1.5454.1.10.3.6.1.24 |
suTemperatureSubscriber Unit temperature reading value (in Celsius).ro INTEGER (-128..127) .1.3.6.1.4.1.5454.1.10.3.6.1.25 |
suRebootAP issues reboot command to a specific subscriber unit.rw Enumeration .1.3.6.1.4.1.5454.1.10.3.6.1.26 |
trapconfig OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.10.4 |
aptrpCountTypes of trap.ro INTEGER .1.3.6.1.4.1.5454.1.10.4.1 |
aptrpDest1IPAddressTrap destination 1 IP address.rw IpAddress .1.3.6.1.4.1.5454.1.10.4.2 |
aptrpDest2IPAddressTrap destination 2 IP address.rw IpAddress .1.3.6.1.4.1.5454.1.10.4.3 |
aptrpTableA table that contains information of Trango trap events . SEQUENCE OF AptrpEntry .1.3.6.1.4.1.5454.1.10.4.4 |
aptrpEntryInformation about a specific Trango trap event. AptrpEntry .1.3.6.1.4.1.5454.1.10.4.4.1 |
aptrpIndexTrap index.ro INTEGER .1.3.6.1.4.1.5454.1.10.4.4.1.1 |
aptrpIDSpecific trap ID.ro INTEGER .1.3.6.1.4.1.5454.1.10.4.4.1.2 |
aptrpCommStrSpecific trap community string.rw DisplayString .1.3.6.1.4.1.5454.1.10.4.4.1.3 |
aptrpEnableEnable a specific Trango trap event or not.rw Enumeration .1.3.6.1.4.1.5454.1.10.4.4.1.4 |
mibinfo OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.10.5 |
mibinfoVersionTrango MIB Version.ro DisplayString .1.3.6.1.4.1.5454.1.10.5.1 |
m5800straps OBJECT IDENTIFIER .1.3.6.1.4.1.5454.1.10.16 |
suLinkUpThe SNMP trap that is generated when a specific SU Associated. TRAP-TYPE .1.3.6.1.4.1.5454.1.10.16.0.7 |
suLinkDownThe SNMP trap that is generated when a specific SU Powered Off. TRAP-TYPE .1.3.6.1.4.1.5454.1.10.16.0.8 |
apOpModeFailureThe SNMP trap that is generated when a specific AP
not being in ap mode during boot up sequence. TRAP-TYPE .1.3.6.1.4.1.5454.1.10.16.0.9 |