TN-QOS-EXT-MIB
AI MIB Summary
The TN-QOS-EXT-MIB module enables the monitoring and configuration of extended Quality of Service (QoS) parameters, such as traffic shaping policies, queue management thresholds, and bandwidth allocation, on Nokia (formerly Alcatel-Lucent) TN (Transport Network) platform hardware. This module facilitates granular control over service-level differentiation and congestion management mechanisms within the transport infrastructure.
The mib module for managing extra QoS features in TN platform products.
Main OID:
tnQosExtMIB.1.3.6.1.4.1.7483.6.9
193
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
193 total| Object Name |
|---|
tnQosExtMIBThe mib module for managing extra QoS features in TN platform products. MODULE-IDENTITY .1.3.6.1.4.1.7483.6.9 |
tnQosExtMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.9.1 |
tnQosExtPortMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.9.1.1 |
tnQosExtPortPolicerTableA port policer table can limit the bandwidth of received frames per port. SEQUENCE OF TnQosExtPortPolicerEntry .1.3.6.1.4.1.7483.6.9.1.1.1 |
tnQosExtPortPolicerEntryAn entry in the table controls the bandwidth of received frames per port. It is located in front of the ingress queue. TnQosExtPortPolicerEntry .1.3.6.1.4.1.7483.6.9.1.1.1.1 |
tnQosExtPortPolicerStatusControls the per port policer status. The policer can limit the
bandwidth of received frames. It is located in front of the Ingress queue.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.1.1.1.1 |
tnQosExtPortPolicerRateControls the rate for the port policer. The rate unit is defined in tnQosExtPortPolicerUnit.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.1.1.1.2 |
tnQosExtPortPolicerUnitthe rate unit for the port policer. Depend on the implement, some unit type may not be supported.rw TnQosExtRateUnitType .1.3.6.1.4.1.7483.6.9.1.1.1.1.3 |
tnQosExtPortPolicerFlowControlControls the port policer flow control. If policer flow control is enabled and the port is in flow control mode,
then pause frames are sent instead of discarding frames.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.1.1.1.4 |
tnQosExtPortQueuePolicerTableA port queue policer table can limit the bandwidth of received frames per port per queue. SEQUENCE OF TnQosExtPortQueuePolicerEntry .1.3.6.1.4.1.7483.6.9.1.1.2 |
tnQosExtPortQueuePolicerEntryAn entry in the table controls the bandwidth of received frames per port per queue. It is located in front of the ingress queue. TnQosExtPortQueuePolicerEntry .1.3.6.1.4.1.7483.6.9.1.1.2.1 |
tnQosExtPortQueuePolicerQidThe ingress queue id for queue policer.
tnQosExtPortQueuePolicerQid is a number in the range (0..(dot1dPortNumTrafficClasses-1)) INTEGER .1.3.6.1.4.1.7483.6.9.1.1.2.1.1 |
tnQosExtPortQueuePolicerStatusControls whether the policer is enabled on the specific queue.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.1.2.1.2 |
tnQosExtPortQueuePolicerRateControls the rate for the queue policer. The rate unit is defined in tnQosExtPortQueuePolicerUnit.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.1.2.1.3 |
tnQosExtPortQueuePolicerUnitThe rate unit for the queue policer. Depend on the implement, some unit type may not be supported.rw TnQosExtRateUnitType .1.3.6.1.4.1.7483.6.9.1.1.2.1.4 |
tnQosExtPortSchedulerTableA port scheduler table controls the egress queue scheduler method per port. SEQUENCE OF TnQosExtPortSchedulerEntry .1.3.6.1.4.1.7483.6.9.1.1.3 |
tnQosExtPortSchedulerEntryAn entry in the table controls the egress queue scheduler method per port. TnQosExtPortSchedulerEntry .1.3.6.1.4.1.7483.6.9.1.1.3.1 |
tnQosExtPortSchedulerModeControls the port egress scheduler mode, strict or weighted.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.1.3.1.1 |
tnQosExtPortSchedulerQueueMaskControls the queues mask which is in the weighted schedule mode. Other queues are in strict mode.rw Bits .1.3.6.1.4.1.7483.6.9.1.1.3.1.2 |
tnQosExtPortSchedulerWeightTableA port scheduler weight table controls the egress queue weight value in weighted scheduler mode per port. SEQUENCE OF TnQosExtPortSchedulerWeightEntry .1.3.6.1.4.1.7483.6.9.1.1.4 |
tnQosExtPortSchedulerWeightEntryAn entry in the table controls the egress queue weight value in weighted scheduler mode per port. TnQosExtPortSchedulerWeightEntry .1.3.6.1.4.1.7483.6.9.1.1.4.1 |
tnQosExtPortSchedulerWeightQidThe egress queue id for scheduler.
tnQosExtPortSchedulerWeightQid is a number in the range (0..(dot1dPortNumTrafficClasses-1)) INTEGER .1.3.6.1.4.1.7483.6.9.1.1.4.1.1 |
tnQosExtPortSchedulerWeightValThe egress queue weight value. the value range is from 1 to 100.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.1.4.1.2 |
tnQosExtPortSchedulerWeightPercentThe egress queue weight in percent view.ro INTEGER .1.3.6.1.4.1.7483.6.9.1.1.4.1.3 |
tnQosExtPortShaperTableA port shaper table can limit the bandwidth of egress frames per port. SEQUENCE OF TnQosExtPortShaperEntry .1.3.6.1.4.1.7483.6.9.1.1.5 |
tnQosExtPortShaperEntryAn entry in the table controls the bandwidth of egress frames per port. TnQosExtPortShaperEntry .1.3.6.1.4.1.7483.6.9.1.1.5.1 |
tnQosExtPortShaperStatusControls the per port shaper status. The shaper can limit the
bandwidth of transmit frames in egress side.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.1.5.1.1 |
tnQosExtPortShaperRateControls the rate for the port shaper. The rate unit is defined in tnQosExtPortShaperUnit.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.1.5.1.2 |
tnQosExtPortShaperUnitthe rate unit for the port shaper. Depend on the implement, some unit type may not be supported.rw TnQosExtRateUnitType .1.3.6.1.4.1.7483.6.9.1.1.5.1.3 |
tnQosExtPortQueueShaperTableA port queue shaper table can limit the bandwidth of egress frames per port per queue. SEQUENCE OF TnQosExtPortQueueShaperEntry .1.3.6.1.4.1.7483.6.9.1.1.6 |
tnQosExtPortQueueShaperEntryAn entry in the table controls the bandwidth of egress frames per port per queue. TnQosExtPortQueueShaperEntry .1.3.6.1.4.1.7483.6.9.1.1.6.1 |
tnQosExtPortQueueShaperQidThe egress queue id for queue shaper.
tnQosExtPortQueueShaperQid is a number in the range (0..(dot1dPortNumTrafficClasses-1)) INTEGER .1.3.6.1.4.1.7483.6.9.1.1.6.1.1 |
tnQosExtPortQueueShaperStatusControls whether the shaper is enabled on the specific queue.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.1.6.1.2 |
tnQosExtPortQueueShaperRateControls the rate for the queue shaper. The rate unit is defined in tnQosExtPortQueueShaperUnit.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.1.6.1.3 |
tnQosExtPortQueueShaperUnitThe rate unit for the queue shaper. Depend on the implement, some unit type may not be supported.rw TnQosExtRateUnitType .1.3.6.1.4.1.7483.6.9.1.1.6.1.4 |
tnQosExtPortQueueShaperExcessControls whether the queue is allowed to use excess bandwidth.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.1.6.1.5 |
tnQosExtPortStormControlTableStorm control settings table. SEQUENCE OF TnQosExtPortStormControlEntry .1.3.6.1.4.1.7483.6.9.1.1.7 |
tnQosExtPortStormControlEntryAn entry in the table represents the storm control settings on an interface. TnQosExtPortStormControlEntry .1.3.6.1.4.1.7483.6.9.1.1.7.1 |
tnQosExtPortStormControlUnicastStatusEnable or disable the storm control status for unicast.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.1.7.1.1 |
tnQosExtPortStormControlUnicastRateThe rate unit is packets per second (pps).rw TnQosExtRateInFps .1.3.6.1.4.1.7483.6.9.1.1.7.1.2 |
tnQosExtPortStormControlMulticastStatusEnable or disable the storm control status for multicast.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.1.7.1.3 |
tnQosExtPortStormControlMulticastRateThe rate unit is packets per second (pps).rw TnQosExtRateInFps .1.3.6.1.4.1.7483.6.9.1.1.7.1.4 |
tnQosExtPortStormControlBroadcastStatusEnable or disable the storm control status for broadcast.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.1.7.1.5 |
tnQosExtPortStormControlBroadcastRateThe rate unit is packets per second (pps).rw TnQosExtRateInFps .1.3.6.1.4.1.7483.6.9.1.1.7.1.6 |
tnQosExtPortStormControl2TableStorm control settings table 2. SEQUENCE OF TnQosExtPortStormControl2Entry .1.3.6.1.4.1.7483.6.9.1.1.8 |
tnQosExtPortStormControl2EntryAn entry in the table represents the storm control settings on an interface. TnQosExtPortStormControl2Entry .1.3.6.1.4.1.7483.6.9.1.1.8.1 |
tnQosExtPortStormControl2FrameTypeThe frame type that storm control takes effect. Implement may use values like:
unicast - unicast frame
broadcast - broadcast frame
unknown - unknown(flooding) frame Enumeration .1.3.6.1.4.1.7483.6.9.1.1.8.1.1 |
tnQosExtPortStormControl2RateControls the rate for the storm control. The rate unit is defined in tnQosExtPortStormControl2RateUnitrw INTEGER .1.3.6.1.4.1.7483.6.9.1.1.8.1.2 |
tnQosExtPortStormControl2RateUnitControls the rate unit for the storm control. The rate is defined in tnQosExtPortStormControl2Raterw TnQosExtRateUnitType .1.3.6.1.4.1.7483.6.9.1.1.8.1.3 |
tnQosExtPortStormControl2StatusEnable or disable the storm control status for the certain frame type.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.9.1.1.8.1.4 |
tnQosExtPortWredTableA table used to configure the Weighted Random Early Detection feature. SEQUENCE OF TnQosExtPortWredEntry .1.3.6.1.4.1.7483.6.9.1.1.9 |
tnQosExtPortWredEntryAn entry in the table used to configure the Weighted Random Early Detection feature. TnQosExtPortWredEntry .1.3.6.1.4.1.7483.6.9.1.1.9.1 |
tnQosExtPortWredQidThe queue id for the weighted random early detection. INTEGER .1.3.6.1.4.1.7483.6.9.1.1.9.1.1 |
tnQosExtPortWredEnableEnable or disable the weighted random early detection for a certain traffic queue.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.9.1.1.9.1.2 |
tnQosExtPortWredThresholdMinControls the lower RED threshold for a certain traffic queue.
If the average queue filling level is below this threshold, the drop probability is zero. This value is restricted to 0-100.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.1.9.1.3 |
tnQosExtPortWredMaxDp1Controls the drop probability for frames marked with Drop Precedence Level 1 when the average queue filling level is 100%.
This value is restricted to 0-100.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.1.9.1.4 |
tnQosExtPortWredMaxDp2Controls the drop probability for frames marked with Drop Precedence Level 2 when the average queue filling level is 100%.
This value is restricted to 0-100.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.1.9.1.5 |
tnQosExtPortWredMaxDp3Controls the drop probability for frames marked with Drop Precedence Level 3 when the average queue filling level is 100%.
This value is restricted to 0-100.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.1.9.1.6 |
tnQosExtPortWredMaxThreshControls the upper RED drop probability or fill level threshold for frames marked with Drop Precedence Level 1 (yellow frames).
This value is restricted to 1-100%.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.1.9.1.7 |
tnQosExtPortWredMaxUnitSelects the unit for Max. Threshold. Possible values are:
Drop Probability: Max. Threshold controls the drop probability just below 100% fill level.
Fill Level: Max. Threshold controls the fill level where drop probability reaches 100%.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.1.9.1.8 |
tnQosExtPortPolicerOrderTableA table used to configure the QoS Policer Order per port. SEQUENCE OF TnQosExtPortPolicerOrderEntry .1.3.6.1.4.1.7483.6.9.1.1.10 |
tnQosExtPortPolicerOrderEntryAn entry in the table used to configure the QoS Policer Order per port. TnQosExtPortPolicerOrderEntry .1.3.6.1.4.1.7483.6.9.1.1.10.1 |
tnQosExtPortPolicerOrderQoS policer order on the entry. depend on implement, the valid policer order would be:
1 - in this mode, QoS policer order is Port Queue Policer first, then Port Policer, ACL Policer is the last (default).
2 - in this mode, QoS policer order is ACL Policer first, then Port Queue Policer, Port Policer is the last.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.1.10.1.1 |
tnQosExtL2CosMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.9.1.2 |
tnQosExtL2CosIfClassifDefaultTableQos layer 2 default Ingress Classification table. SEQUENCE OF TnQosExtL2CosIfClassifDefaultEntry .1.3.6.1.4.1.7483.6.9.1.2.1 |
tnQosExtL2CosIfClassifDefaultEntryAn entry in the table represents the QoS layer 2 default Ingress Classification settings on an interface. TnQosExtL2CosIfClassifDefaultEntry .1.3.6.1.4.1.7483.6.9.1.2.1.1 |
tnQosExtL2CosIfClassifDefaultClassControls the default QoS class (the QoS class for frames not classified in any other way). There is a one to
one mapping between QoS class, queue and priority. A QoS class of 0 (zero) has the lowest priority.
tnQosExtL2CosIfClassifDefaultClass is a number in the range (0..(dot1dPortNumTrafficClasses-1))rw INTEGER .1.3.6.1.4.1.7483.6.9.1.2.1.1.1 |
tnQosExtL2CosIfClassifDefaultDplControls the default DP (Drop Precedence) level for frames not classified in any other way.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.2.1.1.2 |
tnQosExtL2CosIfClassifDefaultPcpControls the default PCP for untagged frames. PCP (Priority Code Point) is a 3-bit field storing the priority
level for the 802.1Q frame. It is also known as User Priority.rw INTEGER (0..7 ) .1.3.6.1.4.1.7483.6.9.1.2.1.1.3 |
tnQosExtL2CosIfClassifDefaultDeiControls the default DEI for untagged frames. DEI (Drop Eligible Indicator) is a 1-bit field in the VLAN tag.rw INTEGER (0..1 ) .1.3.6.1.4.1.7483.6.9.1.2.1.1.4 |
tnQosExtL2CosIfClassifTagTableLayer 2 Cos ingress priority-tagged frame classification mode Table. SEQUENCE OF TnQosExtL2CosIfClassifTagEntry .1.3.6.1.4.1.7483.6.9.1.2.2 |
tnQosExtL2CosIfClassifTagEntryAn entry in the table represents the Layer 2 Cos ingress priority-tagged frame classification mode on an interface. TnQosExtL2CosIfClassifTagEntry .1.3.6.1.4.1.7483.6.9.1.2.2.1 |
tnQosExtL2CosIfClassifTagModeControls the classification mode for priority tagged frames on this interface.
Disabled - Use default QoS class and DP level for priority tagged frames.
Enabled - Use mapped value of PCP and DEI for priority tagged frames.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.2.2.1.1 |
tnQosExtL2CosIfClassifTagMapTableclassified (PCP, DEI) to (QoS class, DP level) mapping table. SEQUENCE OF TnQosExtL2CosIfClassifTagMapEntry .1.3.6.1.4.1.7483.6.9.1.2.3 |
tnQosExtL2CosIfClassifTagMapEntryAn entry in the table represents the mapping of the classified (PCP, DEI) to (QoS class, DP level) values.
This mapping is valid when tnQosExtL2CosIfClassifTagMode is set to Enabled. TnQosExtL2CosIfClassifTagMapEntry .1.3.6.1.4.1.7483.6.9.1.2.3.1 |
tnQosExtL2CosIfClassifTagMapPcpThe carried Pcp (Priority Code Point) field value if recieved frame is IEEE tagged frame. INTEGER (0..7 ) .1.3.6.1.4.1.7483.6.9.1.2.3.1.1 |
tnQosExtL2CosIfClassifTagMapDeiThe carried Dei (Drop Eligible Indicator) field value if recieved frame is IEEE tagged frame. INTEGER (0..1 ) .1.3.6.1.4.1.7483.6.9.1.2.3.1.2 |
tnQosExtL2CosIfClassifTagMapClassThe Traffic Class the received frame is mapped to.
tnQosExtL2CosIfClassifTagMapClass is a number in the range (0..(dot1dPortNumTrafficClasses-1)).rw INTEGER .1.3.6.1.4.1.7483.6.9.1.2.3.1.3 |
tnQosExtL2CosIfClassifTagMapDplThe DP (Drop Precedence) level the received frame is mapped to.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.2.3.1.4 |
tnQosExtL2CosIfTagRemarkingModeTableA table can control the egress frame tag remarking mode on an interface. SEQUENCE OF TnQosExtL2CosIfTagRemarkingModeEntry .1.3.6.1.4.1.7483.6.9.1.2.4 |
tnQosExtL2CosIfTagRemarkingModeEntryAn entry in the table controls the egress frame tag remarking mode on an interface. TnQosExtL2CosIfTagRemarkingModeEntry .1.3.6.1.4.1.7483.6.9.1.2.4.1 |
tnQosExtL2CosIfTagRemarkingModeControls the tag remarking mode for this port.
Classified - Use classified PCP/DEI values.
Default - Use default PCP/DEI values.
Mapped - Use mapped versions of QoS class and DP level.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.2.4.1.1 |
tnQosExtL2CosIfTagRemarkingDefaultTableA table represents the egress frame tag remarking mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to default mode. SEQUENCE OF TnQosExtL2CosIfTagRemarkingDefaultEntry .1.3.6.1.4.1.7483.6.9.1.2.5 |
tnQosExtL2CosIfTagRemarkingDefaultEntryAn entry in the table represents the egress frame tag remarking mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to default mode. TnQosExtL2CosIfTagRemarkingDefaultEntry .1.3.6.1.4.1.7483.6.9.1.2.5.1 |
tnQosExtL2CosIfTagRemarkingDefaultPcpDefault PCP (Priority Code Point) is a 3-bit field storing the priority level for the 802.1Q frame. It is also
known as User Priority. The valid range is 0 - 7. The default is 0.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.2.5.1.1 |
tnQosExtL2CosIfTagRemarkingDefaultDeiDefault DEI (Drop Eligible Indicator) is a 1-bit field in the VLAN tag. The valid range is 0 - 1.
The default is 0.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.2.5.1.2 |
tnQosExtL2CosIfTagRemarkingMappingTableA table represents the egress frame tag remarking mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to mapping mode. SEQUENCE OF TnQosExtL2CosIfTagRemarkingMappingEntry .1.3.6.1.4.1.7483.6.9.1.2.6 |
tnQosExtL2CosIfTagRemarkingMappingEntryAn entry in the table represents the egress frame tag remarking mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to mapping mode. TnQosExtL2CosIfTagRemarkingMappingEntry .1.3.6.1.4.1.7483.6.9.1.2.6.1 |
tnQosExtL2CosIfTagRemarkingClassThe traffic class of the transmit frame belongs to.
tnQosExtIfTagRemarkingClass is a number in the range (0..(dot1dPortNumTrafficClasses-1)). INTEGER .1.3.6.1.4.1.7483.6.9.1.2.6.1.1 |
tnQosExtL2CosIfTagRemarkingDplThe DP (Drop Precedence) level of the transmit frame belongs to. INTEGER .1.3.6.1.4.1.7483.6.9.1.2.6.1.2 |
tnQosExtL2CosIfTagRemarkingPcpPCP (Priority Code Point) is a 3-bit field storing the priority level for the 802.1Q frame. It is also
known as User Priority. The valid range is 0 - 7.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.2.6.1.3 |
tnQosExtL2CosIfTagRemarkingDeiDEI (Drop Eligible Indicator) is a 1-bit field in the VLAN tag. The valid range is 0 - 1.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.2.6.1.4 |
tnQosExtL2CosIfTagRemarkingDplMappingTableA table represents the egress frame tag remarking DP level mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to mapping mode. SEQUENCE OF TnQosExtL2CosIfTagRemarkingDplMappingEntry .1.3.6.1.4.1.7483.6.9.1.2.7 |
tnQosExtL2CosIfTagRemarkingDplMappingEntryAn entry in the table represents the egress frame tag remarking dpl mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to mapping mode. TnQosExtL2CosIfTagRemarkingDplMappingEntry .1.3.6.1.4.1.7483.6.9.1.2.7.1 |
tnQosExtL2CosIfTagRemarkingDplMappingClassifDplThe Classified DP (Drop Precedence) level of the transmit frame belongs to. INTEGER .1.3.6.1.4.1.7483.6.9.1.2.7.1.1 |
tnQosExtL2CosIfTagRemarkingDplMappingDplThe DP (Drop Precedence) level used for tag remarking process.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.2.7.1.2 |
tnQosExtDscpMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.9.1.3 |
tnQosExtDscpIfClassifBaseTableA table represents the QoS classification mode basis on an interface. SEQUENCE OF TnQosExtDscpIfClassifBaseEntry .1.3.6.1.4.1.7483.6.9.1.3.1 |
tnQosExtDscpIfClassifBaseEntryAn entry in the table represents the QoS classification mode basis on an interface. TnQosExtDscpIfClassifBaseEntry .1.3.6.1.4.1.7483.6.9.1.3.1.1 |
tnQosExtDscpIfClassifBaseDscpControls whether the QoS classification mode is based on DSCP value in IP frames on an interface.
Disabled - Disable DSCP based classification.
Enabled - Enable DSCP based classification.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.3.1.1.1 |
tnQosExtDscpIfTransTableA table represents the DSCP ingress translation mode on an interface. SEQUENCE OF TnQosExtDscpIfTransEntry .1.3.6.1.4.1.7483.6.9.1.3.2 |
tnQosExtDscpIfTransEntryAn entry in the table represents the DSCP ingress translation mode on an interface. TnQosExtDscpIfTransEntry .1.3.6.1.4.1.7483.6.9.1.3.2.1 |
tnQosExtDscpIfTransModeControls the ingress DSCP translation setting on an interface.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.3.2.1.1 |
tnQosExtDscpIfTransMapTableA table perform the ingress DSCP translation on an interface. SEQUENCE OF TnQosExtDscpIfTransMapEntry .1.3.6.1.4.1.7483.6.9.1.3.3 |
tnQosExtDscpIfTransMapEntryA entry in this table perform the ingress DSCP translation on an interface. TnQosExtDscpIfTransMapEntry .1.3.6.1.4.1.7483.6.9.1.3.3.1 |
tnQosExtDscpIfTransMapDscpThe received frame carried DSCP value, used for DSCP transmit input.
DSCP (Differentiated Services Code Point) is a field in the header of IP packets for packet classification purposes.
The valid range is 0 - 63 INTEGER .1.3.6.1.4.1.7483.6.9.1.3.3.1.1 |
tnQosExtDscpIfTransMapToDscpThe mapping DSCP value from the frame DSCP value, used for DSCP classification.
DSCP (Differentiated Services Code Point) is a field in the header of IP packets for packet classification purposes.
The valid range is 0 - 63rw INTEGER .1.3.6.1.4.1.7483.6.9.1.3.3.1.2 |
tnQosExtDscpClassifMapTableA table represents the DSCP-Based QoS ingress classification mapping on an interface. SEQUENCE OF TnQosExtDscpClassifMapEntry .1.3.6.1.4.1.7483.6.9.1.3.4 |
tnQosExtDscpClassifMapEntryAn entry in the table represents the DSCP-Based QoS ingress classification mapping on an interface. TnQosExtDscpClassifMapEntry .1.3.6.1.4.1.7483.6.9.1.3.4.1 |
tnQosExtDscpClassifMapDscpDSCP value used to map Qos class and DPL is either translated DSCP value or incoming frame DSCP value. INTEGER .1.3.6.1.4.1.7483.6.9.1.3.4.1.1 |
tnQosExtDscpClassifMapTrustControls whether a specific DSCP value is trusted. Only frames with trused DSCP values are mapped to a specific QoS class and DPL.
Frames with untrusted DSCP values are treated as a non-IP frame.
Enabled - Set DSCP as trusted DSCP.
Disabled - Set DSCP as un-trusted DSCP.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.3.4.1.2 |
tnQosExtDscpClassifMapClassThe traffic class of the recieved frame mapped to.
tnQosExtDscpClassifMapClass is a number in the range (0..(dot1dPortNumTrafficClasses-1)).rw INTEGER .1.3.6.1.4.1.7483.6.9.1.3.4.1.3 |
tnQosExtDscpClassifMapDplThe DP (Drop Precedence) level of the transmit frame mapped torw INTEGER .1.3.6.1.4.1.7483.6.9.1.3.4.1.4 |
tnQosExtDscpIfClassifExtTableA table represents the DSCP classification based on QoS class and DP level on an interface. SEQUENCE OF TnQosExtDscpIfClassifExtEntry .1.3.6.1.4.1.7483.6.9.1.3.5 |
tnQosExtDscpIfClassifExtEntryAn entry in the table represents the DSCP classification based on QoS class and DP level on an interface. TnQosExtDscpIfClassifExtEntry .1.3.6.1.4.1.7483.6.9.1.3.5.1 |
tnQosExtDscpIfClassifExtModeControls the ingress DSCP classification setting on an interface.
Disable - No Ingress DSCP Classification.
DSCP=0 - Classify if incoming (or translated if enabled) DSCP is 0.
Selected: Classify only selected DSCP for which classification is enabled.
All: Classify all DSCP.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.3.5.1.1 |
tnQosExtDscpIfClassifExtDscpTableA table represents the DSCP classification mode per DSCP value. SEQUENCE OF TnQosExtDscpIfClassifExtDscpEntry .1.3.6.1.4.1.7483.6.9.1.3.6 |
tnQosExtDscpIfClassifExtDscpEntryAn entry in the table represents the DSCP classification mode per DSCP value. TnQosExtDscpIfClassifExtDscpEntry .1.3.6.1.4.1.7483.6.9.1.3.6.1 |
tnQosExtDscpIfClassifExtDscpDSCP (Differentiated Services Code Point) is a field in the header of IP packets for packet classification purposes.
The valid range is 0 - 63 INTEGER .1.3.6.1.4.1.7483.6.9.1.3.6.1.1 |
tnQosExtDscpIfClassifExtDscpModeControl the DSCP ingress classification mode on an interface. If port DSCP classification is 'selected',
DSCP will be classified based on QoS class and DP level only for DSCP value with classification mode 'enabled'.
DSCP may be translated DSCP if translation is enabled for the port.
Enabled - Enable DSCP ingress classification.
Disabled - Disable DSCP ingress classification.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.3.6.1.2 |
tnQosExtDscpIfClassifExtMapTableA table config the Dscp ingress classification mapping. SEQUENCE OF TnQosExtDscpIfClassifExtMapEntry .1.3.6.1.4.1.7483.6.9.1.3.7 |
tnQosExtDscpIfClassifExtMapEntryAn entry in this table perform the Dscp ingress classification mapping. TnQosExtDscpIfClassifExtMapEntry .1.3.6.1.4.1.7483.6.9.1.3.7.1 |
tnQosExtDscpIfClassifExtMapClassThe Traffic Class the received frame is mapped to.
tnQosExtDscpIfClassifExtMapClass is a number in the range (0..(dot1dPortNumTrafficClasses-1)). INTEGER .1.3.6.1.4.1.7483.6.9.1.3.7.1.1 |
tnQosExtDscpIfClassifExtMapDplThe DP (Drop Precedence) level the received frame is mapped to. INTEGER .1.3.6.1.4.1.7483.6.9.1.3.7.1.2 |
tnQosExtDscpIfClassifExtMapDscpThe Classified DSCP from QoS class and DP level. The DSCP which needs to be classified depends on interface DSCP
classification and DSCP classification mode. Incoming frame DSCP may be translated before using the value for classification.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.3.7.1.3 |
tnQosExtDscpIfEgressRemarkTableA table represents the DSCP egress remark mode on an interface. SEQUENCE OF TnQosExtDscpIfEgressRemarkEntry .1.3.6.1.4.1.7483.6.9.1.3.8 |
tnQosExtDscpIfEgressRemarkEntryAn entry in the table represents the DSCP egress remark mode on an interface. TnQosExtDscpIfEgressRemarkEntry .1.3.6.1.4.1.7483.6.9.1.3.8.1 |
tnQosExtDscpIfEgressRemarkModeControls the egress frame DSCP field rewrite setting per port.
Disable: No Egress rewrite.
Enable: Rewrite enable without remapped.
Remap DP Unaware: DSCP from analyzer is remapped and frame is remarked with remapped DSCP value.
Remap DP Aware: DSCP from analyzer is remapped and frame is remarked with remapped DSCP value.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.3.8.1.1 |
tnQosExtDscpIfEgressRemarkMapTableA table represents the DSCP egress remark map on an interface. SEQUENCE OF TnQosExtDscpIfEgressRemarkMapEntry .1.3.6.1.4.1.7483.6.9.1.3.9 |
tnQosExtDscpIfEgressRemarkMapEntryAn entry in the table represents the DSCP egress remark map on an interface. TnQosExtDscpIfEgressRemarkMapEntry .1.3.6.1.4.1.7483.6.9.1.3.9.1 |
tnQosExtDscpIfEgressRemarkMapDscpThe classified DSCP value of the specific IP frame, used for DSCP egress remark. DSCP valid range is 0 - 63 INTEGER .1.3.6.1.4.1.7483.6.9.1.3.9.1.1 |
tnQosExtDscpIfEgressRemarkMapDplThe classified DP (Drop Precedence) level of the specific frame, used for DSCP egress remark. INTEGER .1.3.6.1.4.1.7483.6.9.1.3.9.1.2 |
tnQosExtDscpIfEgressRemarkMapToDscpThe DSCP value to which you want to remap for the egress side. This remap is based on classified DSCP and DP level.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.3.9.1.3 |
tnQosExtQclMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.9.1.4 |
tnQosExtQclTableA table used to configure the QoS Control List settings. SEQUENCE OF TnQosExtQclEntry .1.3.6.1.4.1.7483.6.9.1.4.1 |
tnQosExtQclEntryAn entry in the table used to configure the QoS Control List settings. TnQosExtQclEntry .1.3.6.1.4.1.7483.6.9.1.4.1.1 |
tnQosExtQclIndexThe row index of the QCL. INTEGER .1.3.6.1.4.1.7483.6.9.1.4.1.1.1 |
tnQosExtQclIdThe identifier of the QCL.ro INTEGER .1.3.6.1.4.1.7483.6.9.1.4.1.1.2 |
tnQosExtQclNextQclIdSpecify the created ECE is placed before which QCL.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.1.1.3 |
tnQosExtQclPortListThe list of port members for the QCL.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.7483.6.9.1.4.1.1.4 |
tnQosExtQclTagTypeThe frame tag type for matching the QCL. The possible values are:
tagged: The QCL will match tagged frames only.
untagged: The QCL will match untagged frames only.
any: The QCL will match both tagged and untagged frames.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.1.1.5 |
tnQosExtQclTagVlanTypeThe VLAN ID filter type for matching the QCL. It is only significant if tnQosExtQclTagType
is 'tagged' or 'any'. The possible values are:
any: No VLAN ID filter is specified. (VLAN ID filter status is 'don't-care'.)
specific: If you want to filter a specific VLAN ID value with this QCL, choose this
value. A field for entering a specific value appears.
range: If you want to filter a specific VLAN ID range filter with this QCL, choose
this value. A field for entering a range appears.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.1.1.6 |
tnQosExtQclTagVlanValThe Specific VLAN ID filter for matching the QCL. It is only significant if tnQosExtQclTagVlanType
is selected 'specific'.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.7483.6.9.1.4.1.1.7 |
tnQosExtQclTagVlanMinThe Start of Range VLAN ID filter for matching the QCL. It is only significant if tnQosExtQclTagVlanType
is selected 'range'. this value should be lower than tnQosExtQclTagVlanMax value.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.7483.6.9.1.4.1.1.8 |
tnQosExtQclTagVlanMaxThe End of Range VLAN ID filter for matching the QCL. It is only significant if tnQosExtQclTagVlanType
is selected 'range'. this value should be higher than tnQosExtQclTagVlanMin value.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.7483.6.9.1.4.1.1.9 |
tnQosExtQclTagPcpThe PCP value for mataching the QCL. It is only significant if tnQosExtQclTagType
is 'tagged' or 'any'. The possible values are:
any: The QCL will match any PCP value(all bits will be set to 1).
specific: each bit matchs a specific PCP of QCL(from bit0 to bit7).
range: The QCL will match PCP values in the selected range, valid range is depend on the specific implement.
e.g: for S3280, the valid range are bit0-bit1, bit2-bit3, bit4-bit5, bit6-bit7, bit0-bit3 or bit4-bit7.rw Bits .1.3.6.1.4.1.7483.6.9.1.4.1.1.10 |
tnQosExtQclTagDeiThe DEI value for mataching the QCL. It is only significant if tnQosExtQclTagType
is 'tagged' or 'any'. The possible values are: 'any', 'dei0' or 'dei1'.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.1.1.11 |
tnQosExtQclSMacTypeThe source MAC address filter type for matching the QCL. The possible values are:
any: No source MAC address filter is specified. (source MAC address filter status is 'don't-care'.)
specific: choose this value to filter a specific source MAC address value with this QCL.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.1.1.12 |
tnQosExtQclSMacThe source MAC address filter for matching the QCL.
In S3280 implement, only MAC OUI(first three octets) are used for MAC address matching process.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.7483.6.9.1.4.1.1.13 |
tnQosExtQclDMacTypeThe destination MAC address filter for matching the QCL. The possible values are:
any: No destination MAC address filter is specified. (destination MAC address filter status is 'don't-care'.)
unicast: Match the unicast destination MAC address for the QCL.
multicast: Match the multicast destination MAC address for the QCL.
broadcast: Match the broadcast destination MAC address for the QCL.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.1.1.14 |
tnQosExtQclFrameTypeThe frame type for the QCL. The possible values are:
any: The QCL will match any frame type.
ethernet: The QCL will match Ethernet frame type.
llc: The QCL will match LLC frame type.
snap: The QCL will match SNAP frame type.
ipv4: The QCL will match IPv4 frames.
ipv6: The QCL will match IPv6 frames.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.1.1.15 |
tnQosExtQclActClassDefaultDeterme the type of matched frame traffic class modification.
default: QCL do not change the traffic class of the matched received frames.
specific: QCL will change the traffic class to the specific value of the matched received frames.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.1.1.16 |
tnQosExtQclActClassIf a frame matches the QCE it will be put in the queue. It is only significant if tnQosExtQclActClassDefault
is selected 'specific' value.
tnQosExtQclActClass is a number in the range (0..(dot1dPortNumTrafficClasses-1)).rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.1.1.17 |
tnQosExtQclActDplDefaultDeterme the type of matched frame traffic DP (Drop Precedence) level modification.
default: QCL do not change the DP (Drop Precedence) level of the matched received frames.
specific: QCL will change the DP (Drop Precedence) level to the specific value of the matched received frames.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.1.1.18 |
tnQosExtQclActDplIf a frame matches the QCE then DP level will set to the value. It is only significant if tnQosExtQclActDplDefault
is selected 'specific' value.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.1.1.19 |
tnQosExtQclActDscpDefaultDeterme the type of matched frame DSCP modification.
default: QCL do not change the DSCP of the matched received frames.
specific: QCL will change the DSCP to the specific value of the matched received frames.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.1.1.20 |
tnQosExtQclActDscpIf a frame matches the QCE then DSCP will be classified with the value. It is only significant if tnQosExtQclActDscpDefault
is selected 'specific' value.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.1.1.21 |
tnQosExtQclConflictQCE status. It may be that resources required to add a QCE may not be available; in
that case it shows conflict status as 'yes', otherwise it is always 'no'.ro Enumeration .1.3.6.1.4.1.7483.6.9.1.4.1.1.22 |
tnQosExtQclStatusThe status of this conceptual row entry of QCL table. This object isused to manage the
creation and deletion of conceptual rows.
The status column has six defined values:
- 'active', which indicates that the conceptual row is
available for use by the managed device;
- 'notInService', which indicates that the conceptual
row exists in the agent, but is unavailable for use by
the managed device (see NOTE below);
- 'notReady', which indicates that the conceptual row
exists in the agent, but is missing information
necessary in order to be available for use by the
managed device;
- 'createAndGo', which is supplied by a management
station wishing to create a new instance of a
conceptual row and to have its status automatically set
to active, making it available for use by the managed
device;
- 'createAndWait', which is supplied by a management
station wishing to create a new instance of a
conceptual row (but not make it available for use by
the managed device); and,
- 'destroy', which is supplied by a management station
wishing to delete all of the instances associated with
an existing conceptual row.
For a detailed description of this object, please refer to
SNMPv2-TC MIB.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7483.6.9.1.4.1.1.23 |
tnQosExtQclL2TableA table used to configure the QoS Control List layer 2 frame settings. SEQUENCE OF TnQosExtQclL2Entry .1.3.6.1.4.1.7483.6.9.1.4.2 |
tnQosExtQclL2EntryAn entry in the table used to configure the QoS Control List layer 2 fram settings. TnQosExtQclL2Entry .1.3.6.1.4.1.7483.6.9.1.4.2.1 |
tnQosExtQclEtherTypeThe Ether type filter for matching the QCL. It is only significant if tnQosExtQclFrameType
'ethernet' is selected. The possible values are:
any: No Ether type filter is specified. (Ether type filter status is 'don't-care'.)
specific: Choose this value to filter a specific Ether type value with this QCL.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.2.1.1 |
tnQosExtQclEtherValWhen tnQosExtQclEtherType is selected 'Specific' value, you can enter a specific value.
The allowed value is from 0x0600 through 0xFFFF. If implement supports ipv4 or ipv6 selection in
tnQosExtQclFrameType, the value 0x0800(ipv4) or 0x86DD(ipv6) are reserved from setting.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.2.1.2 |
tnQosExtQclLlcSsapTypeThe LLC SSAP type filter for matching the QCL. It is only significant if tnQosExtQclFrameType
'llc' is selected. The possible values are:
any: No SSAP type filter is specified. (SSAP type filter status is 'don't-care'.)
specific: Choose this value to filter a specific SSAP type value with this QCL.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.2.1.3 |
tnQosExtQclLlcSsapValWhen tnQosExtQclLlcSsapType is selected 'Specific' value, you can enter a specific value.
The allowed value is from 0 through 255.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.2.1.4 |
tnQosExtQclLlcDsapTypeThe LLC DSAP type filter for matching the QCL. It is only significant if tnQosExtQclFrameType
'llc' is selected. The possible values are:
any: No DSAP type filter is specified. (DSAP type filter status is 'don't-care'.)
specific: Choose this value to filter a specific DSAP type value with this QCL.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.2.1.5 |
tnQosExtQclLlcDsapValWhen tnQosExtQclLlcDsapType is selected 'Specific' value, you can enter a specific value.
The allowed value is from 0 through 255.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.2.1.6 |
tnQosExtQclLlcControlTypeThe LLC Control type filter for matching the QCL. It is only significant if tnQosExtQclFrameType
'llc' is selected. The possible values are:
any: No Control type filter is specified. (Control type filter status is 'don't-care'.)
specific: Choose this value to filter a specific Control type value with this QCL.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.2.1.7 |
tnQosExtQclLlcControlValWhen tnQosExtQclLlcControlType is selected 'Specific' value, you can enter a specific value.
The allowed value is from 0 through 255.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.2.1.8 |
tnQosExtQclSnapPidTypeThe SNAP PID type filter for matching the QCL. It is only significant if tnQosExtQclFrameType
'snap' is selected. The possible values are:
any: No SNAP PIDtype filter is specified. (SNAP PID type filter status is 'don't-care'.)
specific: Choose this value to filter a specific SNAP PID type value with this QCL.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.2.1.9 |
tnQosExtQclSnapPidValWhen tnQosExtQclSnapPidType is selected 'Specific' value, you can enter a specific value.
The allowed value is from 0x600 through 0xFFFF. If implement supports ipv4 or ipv6 selection in
tnQosExtQclFrameType, the value 0x0800(ipv4) or 0x86DD(ipv6) are reserved from setting.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.2.1.10 |
tnQosExtQclIpTableA table used to configure the QoS Control List IP settings. SEQUENCE OF TnQosExtQclIpEntry .1.3.6.1.4.1.7483.6.9.1.4.3 |
tnQosExtQclIpEntryAn entry in the table used to configure the QoS Control List IP settings. TnQosExtQclIpEntry .1.3.6.1.4.1.7483.6.9.1.4.3.1 |
tnQosExtQclProtoTypeThe IP protocol for matching the QCL.The possible values are:
any: No protocol filter is specified. (Protocol filter status is 'don't-care'.)
udp: Specify the UDP for matching the QCL.
tcp: Specify the TCP for matching the QCL.
specific: Choose this value to filter a specific protocol value with this QCL.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.3.1.1 |
tnQosExtQclProtoValWhen tnQosExtQclProtoType is selected 'Specific' value, you can enter a specific value.
The allowed value is from 0 through 255. If implement supports udp or tcp selection in
tnQosExtQclProtoType, the value 6(tcp) or 17(udp) are reserved from setting.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.3.1.2 |
tnQosExtQclDscpTypeThe DSCP filter for matching the QCL. The possible values are:
any: No DSCP filter is specified. (DSCP filter status is 'don't-care'.)
specific: choose this value to filter a specific DSCP value with this QCL.
range: Choose this value to filter a specific DSCP range filter with this QCL.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.3.1.3 |
tnQosExtQclDscpValWhen tnQosExtQclDscpType is selected 'Specific' value, you can enter a specific value.
The allowed value is from 0 through 63.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.3.1.4 |
tnQosExtQclDscpMinWhen tnQosExtQclDscpType is selected 'Range' value, you can enter a specific range.
this value should be lower than tnQosExtQclDscpMax value.
The allowed range start is from 0 through 63.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.3.1.5 |
tnQosExtQclDscpMaxWhen tnQosExtQclDscpType is selected 'Range' value, you can enter a specific range.
this value should be higher than tnQosExtQclDscpMin value.
The allowed range end is from 0 through 63.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.3.1.6 |
tnQosExtQclSrcIpTypeThe source IP address type filter for matching the QCL.
The possible values are:
any: No source IP address filter is specified. (source IP address filter status is 'don't-care'.)
specific: Choose this value to filter a specific source IP address with this QCL.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.3.1.7 |
tnQosExtQclSrcIpAddrTypeSpecify the tnQosExtQclSrcIpAddr type.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.7483.6.9.1.4.3.1.8 |
tnQosExtQclSrcIpAddrWhen tnQosExtQclSrcIpType is selected 'Specific' value, you can enter a specific host or network address.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7483.6.9.1.4.3.1.9 |
tnQosExtQclSrcIpMaskTypeSpecify the tnQosExtQclSrcIpMask type.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.7483.6.9.1.4.3.1.10 |
tnQosExtQclSrcIpMaskWhen tnQosExtQclSrcIpType is selected 'Specific' value, you can enter a specific network mask for the source IP address.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.7483.6.9.1.4.3.1.11 |
tnQosExtQclIpv4FragmentThe IPv4 Fragment for matching the QCL. This involves the settings for the More Fragments (MF) bit
and the Fragment Offset (FRAG OFFSET) field for an IPv4 frame. The possible values are:
any: The QCL will match any MF bit.
fragment: IPv4 frames where the MF bit is set or the FRAG OFFSET field is greater than zero must be
able to match this entry.
nonfragment: IPv4 frames where the MF bit is set or the FRAG OFFSET field is greater than zero must
not be able to match this entry.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.3.1.12 |
tnQosExtQclTcpUdpSportTypeThe TCP/UDP source port for matching the QCL. It is only significant if protocol
filter 'UDP' or 'TCP' is selected. The possible values are:
any: No TCP/UDP source port filter is specified. (Source port filter status is 'don't-care'.)
specific: Choose this value to filter a specific TCP/UDP source port No. with this QCL.
range: Choose this value to filter a specific TCP/UDP source port range filter with this QCL.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.3.1.13 |
tnQosExtQclTcpUdpSportValWhen tnQosExtQclTcpUdpSportType is selected 'Specific' value, you can enter a specific value.
The allowed value is from 0 through 65535.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.3.1.14 |
tnQosExtQclTcpUdpSportMinWhen tnQosExtQclTcpUdpSportType is selected 'Range' value, you can enter a specific range.
this value should be lower than tnQosExtQclTcpUdpSportMax value.
The allowed range start is from 0 through 65535.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.3.1.15 |
tnQosExtQclTcpUdpSportMaxWhen tnQosExtQclTcpUdpSportType is selected 'Range' value, you can enter a specific range.
this value should be higher than tnQosExtQclTcpUdpSportMin value.
The allowed range end is from 0 through 65535.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.3.1.16 |
tnQosExtQclTcpUdpDportTypeThe TCP/UDP destination port for matching the QCL. It only significant if protocol
filter 'UDP' or 'TCP' is selected. The possible values are:
any: No TCP/UDP destination port filter is specified. (Source port filter status is 'don't-care'.)
specific: Choose this value to filter a specific TCP/UDP source port No. with this QCL.
range: Choose this value to filter a specific TCP/UDP source port range filter with this QCL.rw Enumeration .1.3.6.1.4.1.7483.6.9.1.4.3.1.17 |
tnQosExtQclTcpUdpDportValWhen tnQosExtQclTcpUdpDportVal is selected 'Specific' value, you can enter a specific value.
The allowed value is from 0 through 65535.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.3.1.18 |
tnQosExtQclTcpUdpDportMinWhen tnQosExtQclTcpUdpDportVal is selected 'Range' value, you can enter a specific range.
this value should be lower than tnQosExtQclTcpUdpDportMax value.
The allowed range start is from 0 through 65535.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.3.1.19 |
tnQosExtQclTcpUdpDportMaxWhen tnQosExtQclTcpUdpDportVal is selected 'Range' value, you can enter a specific range.
this value should be higher than tnQosExtQclTcpUdpDportMin value.
The allowed range end is from 0 through 65535.rw INTEGER .1.3.6.1.4.1.7483.6.9.1.4.3.1.20 |