TN-ETHSOAM-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for TN-ETHSOAM-MIB.
TBD
Main OID:
tnEthSoamMIB.1.3.6.1.4.1.7483.6.105
159
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
159 total| Object Name |
|---|
tnEthSoamMIBTBD MODULE-IDENTITY .1.3.6.1.4.1.7483.6.105 |
tnEthSoamMIBNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.105.0 |
tnEthSoamFaultAlarmAn EthSoam has a persistent defect condition. A notification
(fault alarm) is sent to the management entity with the OID
of the EthSoam that has detected the fault.
The management entity receiving the notification can identify
the system from the network source address of the
notification, and can identify the EthSoam reporting the defect
by the indices in the OID of the variables in the notification:
tnEthSoamInstance - Also the index of the EthSoam status table entry
(tnEthSoamStatusTable). NOTIFICATION-TYPE .1.3.6.1.4.1.7483.6.105.0.1 |
tnEthSoamPeerFaultAlarmAn EthSoamPeer has a persistent defect condition. A notification
(fault alarm) is sent to the management entity with the OID
of the EthSoamPeer that has detected the fault.
The management entity receiving the notification can identify
the system from the network source address of the
notification, and can identify the EthSoamPeer reporting the defect
by the indices in the OID of the variables in the notification:
tnEthSoamInstance - Also the index of the EthSoam Peer status table entry
(tnEthSoamPeerStatusTable).
tnEthSoamPeerStatusMepId - Also the index of the EthSoam Peer status table entry
(tnEthSoamPeerStatusTable). NOTIFICATION-TYPE .1.3.6.1.4.1.7483.6.105.0.2 |
tnEthSoamMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.105.1 |
tnEthSoamMPMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.105.1.1 |
tnEthSoamMPTableThis table provides configuration of SOAM Maintenance Point. SEQUENCE OF TnEthSoamMPEntry .1.3.6.1.4.1.7483.6.105.1.1.1 |
tnEthSoamMPEntryA entry in the table represents a configuration for local SOAM. TnEthSoamMPEntry .1.3.6.1.4.1.7483.6.105.1.1.1.1 |
tnEthSoaminstanceThis is the configuration of the two possible Maintenance Association Identifier formats.
ITU ICC: This is defined by ITU. 'ICC' can be max. 6 char. 'MEG id' can be max. 7 char.
IEEE String: This is defined by IEEE. 'Domain Name' can be max. 8 char. 'MEG id' can be max. 8 char. Unsigned32 .1.3.6.1.4.1.7483.6.105.1.1.1.1.1 |
tnEthSoamDomaintypeThe Domain Mode affects the OAM. The allowed values are
Port: This is a MEP in the Port Domain. 'Flow Instance' is a Port.
Esp: Future use.
Evc: This is a MEP in the EVC Domain. 'Flow Instance' is a EVC.
Mpls: Future use.
Vlan: This is a MEP in the VLAN Domain. 'Flow Instance' is a VLAN.rw TnEthSoamType .1.3.6.1.4.1.7483.6.105.1.1.1.1.2 |
tnEthSoamModeMEP: This is a Maintenance Entity End Point.
MIP: This is a Maintenance Entity Intermediate Point.rw Enumeration .1.3.6.1.4.1.7483.6.105.1.1.1.1.3 |
tnEthSoamdirectionDirection in which the MP faces on the Bridge Port.rw Dot1agCfmMpDirection .1.3.6.1.4.1.7483.6.105.1.1.1.1.4 |
tnEthSoamresidencePortThis object is the interface index of the interface either a
bridge port, or an aggregated IEEE 802.1 link within a bridge
port, to which the MEP is attached.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.7483.6.105.1.1.1.1.5 |
tnEthSoamlevelLevel of the Maintenance Point.rw Dot1agCfmMDLevel .1.3.6.1.4.1.7483.6.105.1.1.1.1.6 |
tnEthSoamFlowInstanceThe MEP is related to this flow - See 'Domain'.rw INTEGER .1.3.6.1.4.1.7483.6.105.1.1.1.1.7 |
tnEthSoamTaggedVIDPort MEP: An outer C/S-tag (depending on VLAN Port Type) is added with this VID.
Entering '0' means no TAG added.rw VlanIdOrNone (Q-BRIDGE-MIB) .1.3.6.1.4.1.7483.6.105.1.1.1.1.8 |
tnEthSoamAlarmAn active alarm on the MEP.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.1.1.1.9 |
tnEthSoamStatusThe status of the row.
The writable columns in a row can not be changed if the row
is active. All columns must have a valid value before a row
can be activated.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.1.1.1.11 |
tnEthSoamPeerCfgMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.105.1.2 |
tnEthSoamPeerCfgTableThis table has entries which generate a configuration for peer SOAM. SEQUENCE OF TnEthSoamPeerCfgEntry .1.3.6.1.4.1.7483.6.105.1.2.1 |
tnEthSoamPeerCfgEntryA entry in the table represents a configuration for peer SOAM. TnEthSoamPeerCfgEntry .1.3.6.1.4.1.7483.6.105.1.2.1.1 |
tnEthSoamPeerCfgMepIdThe ID of the MEP. Dot1agCfmMepId .1.3.6.1.4.1.7483.6.105.1.2.1.1.1 |
tnEthSoamPeerCfgUnicastMacThis MAC will be used when unicast is selected with this peer MEP.
Also this MAC is used to create HW checking of receiving CCM PDU (LOC detection) from this MEP.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.2.1.1.2 |
tnEthSoamPeerCfgRowStaterow status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.2.1.1.3 |
tnEthSoamPeerStatusMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.105.1.3 |
tnEthSoamPeerStatusTableThis table provides configuration about the SOAM that provide
OAM services. SEQUENCE OF TnEthSoamPeerStatusEntry .1.3.6.1.4.1.7483.6.105.1.3.1 |
tnEthSoamPeerStatusEntryThis entry represents configuration about the SOAM that provide
OAM services. TnEthSoamPeerStatusEntry .1.3.6.1.4.1.7483.6.105.1.3.1.1 |
tnEthSoamPeerStatusMepIdMEPID. Dot1agCfmMepId .1.3.6.1.4.1.7483.6.105.1.3.1.1.1 |
tnEthSoamPeerStatuscLOCFault Cause indicating that no CCM has been received (in 3,5 periods) - from this peer MEP.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.3.1.1.2 |
tnEthSoamPeerStatuscRDIFault Cause indicating that a CCM is received with Remote Defect Indication - from this peer MEP.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.3.1.1.3 |
tnEthSoamPeerStatuscPeriodFault Cause indicating that a CCM is received with a period different what is configured for this MEP - from this peer MEP.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.3.1.1.4 |
tnEthSoamPeerStatuscPriorityFault Cause indicating that a CCM is received with a priority different what is configured for this MEP - from this peer MEP.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.3.1.1.5 |
tnEthSoamAPSCfgMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.105.1.4 |
tnEthSoamAPSCfgTableThis table provides configuration about the APSCfg that provide
OAM services. SEQUENCE OF TnEthSoamAPSCfgEntry .1.3.6.1.4.1.7483.6.105.1.4.1 |
tnEthSoamAPSCfgEntryThis entry represents configuration about the SOAM that provide
OAM services. TnEthSoamAPSCfgEntry .1.3.6.1.4.1.7483.6.105.1.4.1.1 |
tnEthSoamAPSCfgEnableAutomatic Protection Switching protocol information transportation based on transmitting/receiving R-APS/L-APS PDU can be enabled/disabled.
Must be enabled to support ERPS/ELPS implementing APS. This is only valid with one Peer MEP configured.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.4.1.1.1 |
tnEthSoamAPSCfgPriorityThe priority to be inserted as PCP bits in TAG (if any).rw IEEE8021PriorityValue (IEEE8021-TC-MIB) .1.3.6.1.4.1.7483.6.105.1.4.1.1.2 |
tnEthSoamAPSCfgCastSelection of APS PDU transmitted unicast or multi-cast.
The unicast MAC will be taken from the 'Unicast Peer MAC' configuration.
Unicast is only valid for L-APS - see 'Type'.
The R-APS PDU is always transmitted with multi-cast MAC described in G.8032.rw Enumeration .1.3.6.1.4.1.7483.6.105.1.4.1.1.3 |
tnEthSoamAPSCfgTypeR-APS: APS PDU is transmitted as R-APS - this is for ERPS.
L-APS: APS PDU is transmitted as L-APS - this is for ELPS.rw Enumeration .1.3.6.1.4.1.7483.6.105.1.4.1.1.4 |
tnEthSoamAPSCfgLastOctetThis is the last octet of the transmitted and expected RAPS multi-cast MAC.
In G.8031 (03/2010) a RAPS multi-cast MAC is defined as 01-19-A7-00-00-XX.
In current standard the value for this last octet is '01' and the usage of other values is for further study.rw Unsigned32 .1.3.6.1.4.1.7483.6.105.1.4.1.1.5 |
tnEthSoamClientCfgMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.105.1.5 |
tnEthSoamClientCfgTableThis table provides configuration about the Link Trace reply that provide
OAM services. SEQUENCE OF TnEthSoamClientCfgEntry .1.3.6.1.4.1.7483.6.105.1.5.1 |
tnEthSoamClientCfgEntryThis entry represents configuration about the Client Configuration that provide
OAM services. TnEthSoamClientCfgEntry .1.3.6.1.4.1.7483.6.105.1.5.1.1 |
tnEthSoamClientCfgDomainThe domain of the client layer. Must be EVC.rw TnEthSoamType .1.3.6.1.4.1.7483.6.105.1.5.1.1.1 |
tnEthSoamClientCfgLevelClient layer level - meaning that PDU transmitted in client layer flows will be on this level.rw Dot1agCfmMDLevel .1.3.6.1.4.1.7483.6.105.1.5.1.1.2 |
tnEthSoamClientCfgFlow1Client layer flow instance numbers.rw Unsigned32 .1.3.6.1.4.1.7483.6.105.1.5.1.1.3 |
tnEthSoamClientCfgFlow2Client layer flow instance numbers.rw Unsigned32 .1.3.6.1.4.1.7483.6.105.1.5.1.1.4 |
tnEthSoamClientCfgFlow3Client layer flow instance numbers.rw Unsigned32 .1.3.6.1.4.1.7483.6.105.1.5.1.1.5 |
tnEthSoamClientCfgFlow4Client layer flow instance numbers.rw Unsigned32 .1.3.6.1.4.1.7483.6.105.1.5.1.1.6 |
tnEthSoamClientCfgFlow5Client layer flow instance numbers.rw Unsigned32 .1.3.6.1.4.1.7483.6.105.1.5.1.1.7 |
tnEthSoamClientCfgFlow6Client layer flow instance numbers.rw Unsigned32 .1.3.6.1.4.1.7483.6.105.1.5.1.1.8 |
tnEthSoamClientCfgFlow7Client layer flow instance numbers.rw Unsigned32 .1.3.6.1.4.1.7483.6.105.1.5.1.1.9 |
tnEthSoamClientCfgFlow8Client layer flow instance numbers.rw Unsigned32 .1.3.6.1.4.1.7483.6.105.1.5.1.1.10 |
tnEthSoamClientCfgFlow9Client layer flow instance numbers.rw Unsigned32 .1.3.6.1.4.1.7483.6.105.1.5.1.1.11 |
tnEthSoamClientCfgFlow10Client layer flow instance numbers.rw Unsigned32 .1.3.6.1.4.1.7483.6.105.1.5.1.1.12 |
tnEthSoamLocalCfgMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.105.1.6 |
tnEthSoamLocalCfgTableThis table has entries which generate a configuration for local SOAM. SEQUENCE OF TnEthSoamLocalCfgEntry .1.3.6.1.4.1.7483.6.105.1.6.1 |
tnEthSoamLocalCfgEntryA entry in the table represents a configuration for local SOAM. TnEthSoamLocalCfgEntry .1.3.6.1.4.1.7483.6.105.1.6.1.1 |
tnEthSoamFormatThis is the configuration of the two possible Maintenance Association Identifier formats.
ITU ICC: This is defined by ITU. 'ICC' can be max. 6 char. 'MEG id' can be max. 7 char.
IEEE String: This is defined by IEEE. 'Domain Name' can be max. 8 char. 'MEG id' can be max. 8 char.rw Enumeration .1.3.6.1.4.1.7483.6.105.1.6.1.1.1 |
tnEthSoamDomainNameThis is either ITU ICC (MEG ID value[1-6]) or IEEE Maintenance Domain Name - depending on 'Format'. See 'Format'.rw OCTET STRING .1.3.6.1.4.1.7483.6.105.1.6.1.1.2 |
tnEthSoamMegOrMaNameThis is either ITU UMC (MEG ID value[7-13]) or IEEE Short MA Name - depending on 'Format'. See 'Format'.
In case of ITU ICC format this can be max. 7 char. If only 6 char. is entered the MEG ID value[13] will become NULL.rw OCTET STRING .1.3.6.1.4.1.7483.6.105.1.6.1.1.3 |
tnEthSoamMepIDThis value will become the transmitted two byte CCM MEP ID.rw Dot1agCfmMepId .1.3.6.1.4.1.7483.6.105.1.6.1.1.4 |
tnEthSoamCcmIntervalInterval between CCM transmissions to be used by all MEPs
in the MA.rw Enumeration .1.3.6.1.4.1.7483.6.105.1.6.1.1.5 |
tnEthSoamEVCQosThis is only relevant for a EVC MEP.
This is the Qos of the EVC used for getting QoS counters for Loss Measurement.rw INTEGER .1.3.6.1.4.1.7483.6.105.1.6.1.1.6 |
tnEthSoamEVCPolicyIDThis is relevant for an EVC Egress/Up-MEP. This is the Policy number of the relevant ECE.
The Policy ID that the generated TST frames will get as IS1 action. Can be the same as any ECE Policy Number,
enabling it to hit the same ACL and thereby the same EVC policer.rw INTEGER .1.3.6.1.4.1.7483.6.105.1.6.1.1.7 |
tnEthSoamVOEThis will attempt to utilize VOE HW for MEP implementation. Not all platforms support VOE.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.6.1.1.8 |
tnEthSoamStatusMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.105.1.7 |
tnEthSoamStatusTableThis table provides configuration about the SOAM that provide
OAM services. SEQUENCE OF TnEthSoamStatusEntry .1.3.6.1.4.1.7483.6.105.1.7.1 |
tnEthSoamStatusEntryThis entry represents configuration about the SOAM that provide
OAM services. TnEthSoamStatusEntry .1.3.6.1.4.1.7483.6.105.1.7.1.1 |
tnEthSoamStatusCCMLevelFault Cause indicating that a CCM is received with a lower level than the configured for this MEP.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.7.1.1.1 |
tnEthSoamStatusCCMMegFault Cause indicating that a CCM is received with a MEG ID different from configured for this MEP.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.7.1.1.2 |
tnEthSoamStatusCCMMepFault Cause indicating that a CCM is received with a MEP ID different from all 'Peer MEP ID' configured for this MEP.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.7.1.1.3 |
tnEthSoamStatusAISFault Cause indicating that AIS PDU is received.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.7.1.1.4 |
tnEthSoamStatusCLKFault Cause indicating that LCK PDU is received.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.7.1.1.5 |
tnEthSoamStatusSSFFault Cause indicating that server layer is indicating Signal Fail.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.7.1.1.6 |
tnEthSoamStatusBLKThe consequent action of blocking service frames in this flow is active.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.7.1.1.7 |
tnEthSoamStatusTSFThe consequent action of indicating Trail Signal Fail to-wards protection is active.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.7.1.1.8 |
tnEthSoamLossStateMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.105.1.8 |
tnEthSoamLossStateTableThis table has entries which generate a configuration for loss measurement State. SEQUENCE OF TnEthSoamLossStateEntry .1.3.6.1.4.1.7483.6.105.1.8.1 |
tnEthSoamLossStateEntryA entry in the table represents a configuration for loss measurement State. TnEthSoamLossStateEntry .1.3.6.1.4.1.7483.6.105.1.8.1.1 |
tnEthSoamLossStateTxCountThe accumulated Tx frame loss count.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.8.1.1.1 |
tnEthSoamLossStateRxCountThe accumulated Rx frame loss count.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.8.1.1.2 |
tnEthSoamLossStateNELossCountThe accumulated near end frame loss count - since last 'clear'.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.8.1.1.3 |
tnEthSoamLossStateFELossCountThe accumulated far end frame loss count - since last 'clear'.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.8.1.1.4 |
tnEthSoamLossStateNELossRatioThe near end frame loss ratio calculated based on the near end frame loss count and far end
frame transmitted - in the latest 'FLR Interval'. The result is given in percent.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.8.1.1.5 |
tnEthSoamLossStateFELossRatioThe far end frame loss ratio calculated based on the far end frame loss count and
near end frame transmitted - in the latest 'FLR Interval'. The result is given in percent.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.8.1.1.6 |
tnEthSoamLossStateActionSet of this check and save will clear the accumulated counters and restart ratio calculation.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.8.1.1.7 |
tnEthSoamTSExtMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.105.1.9 |
tnEthSoamTSExtTableThis table has entries which generate a configuration for test signal. SEQUENCE OF TnEthSoamTSExtEntry .1.3.6.1.4.1.7483.6.105.1.9.1 |
tnEthSoamTSExtEntryA entry in the table represents a configuration for test signal. TnEthSoamTSExtEntry .1.3.6.1.4.1.7483.6.105.1.9.1.1 |
tnEthSoamTSSeqNumsequence number.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.9.1.1.1 |
tnEthSoamTSStateRxRateThe current received TST frame bit rate in 100 Kbps. This is calculated on a 1 s.
basis, starting when first TST frame is received after 'Clear'. The frame size used for this calculation is
the first received after 'Clear' .ro INTEGER .1.3.6.1.4.1.7483.6.105.1.9.1.1.2 |
tnEthSoamTSStateActionThis will clear all Test Signal State. Transmission of TST frame will be restarted.
Calculation of 'Rx frame count', 'RX rate' and 'Test time' will be started when receiving first TST frame.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.9.1.1.3 |
tnEthSoamTestCfgPatternThis attribute specifies the type of test pattern to be
sent or received in an OAM PDU Test TLV.rw TnEthSoamTestPatternType .1.3.6.1.4.1.7483.6.105.1.9.1.1.4 |
tnEthSoamLtmMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.105.1.10 |
tnEthSoamLtmTableThis table provides configuration about ltm priority that provide
OAM services. SEQUENCE OF TnEthSoamLtmEntry .1.3.6.1.4.1.7483.6.105.1.10.1 |
tnEthSoamLtmEntryThis entry represents configuration about the SOAM that provide
OAM services. TnEthSoamLtmEntry .1.3.6.1.4.1.7483.6.105.1.10.1.1 |
tnEthSoamltmPriorityThe priority to be inserted as PCP bits in TAG (if any).rw IEEE8021PriorityValue (IEEE8021-TC-MIB) .1.3.6.1.4.1.7483.6.105.1.10.1.1.1 |
tnEthSoamLtrMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.105.1.11 |
tnEthSoamLtrTableThis table provides configuration about ltm priority that provide
OAM services. SEQUENCE OF TnEthSoamLtrEntry .1.3.6.1.4.1.7483.6.105.1.11.1 |
tnEthSoamLtrEntryThis entry represents configuration about the SOAM that provide
OAM services. TnEthSoamLtrEntry .1.3.6.1.4.1.7483.6.105.1.11.1.1 |
tnEthSoamLtrDirectionThe priority to be inserted as PCP bits in TAG (if any).ro Enumeration .1.3.6.1.4.1.7483.6.105.1.11.1.1.1 |
tnEthSoamAisCfgMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.105.1.12 |
tnEthSoamAisCfgTableThis table provides configuration about ais that provide
OAM services. SEQUENCE OF TnEthSoamAisCfgEntry .1.3.6.1.4.1.7483.6.105.1.12.1 |
tnEthSoamAisCfgEntryThis entry represents configuration about the SOAM that provide
OAM services. TnEthSoamAisCfgEntry .1.3.6.1.4.1.7483.6.105.1.12.1.1 |
tnEthSoamAisCfgProtectionSelecting this means that the first 3 AIS PDU is transmitted as fast as possible -
in case of using this for protection in the end point.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.12.1.1.1 |
tnEthSoamDmCfgMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.105.1.13 |
tnEthSoamDmCfgTableThis table provides configuration about the Delay Measurement that provide
OAM services. SEQUENCE OF TnEthSoamDmCfgEntry .1.3.6.1.4.1.7483.6.105.1.13.1 |
tnEthSoamDmCfgEntryThis entry represents configuration about the Delay Measurement that provide
OAM services. TnEthSoamDmCfgEntry .1.3.6.1.4.1.7483.6.105.1.13.1.1 |
tnEthSoamDmCfgEnableDelay Measurement based on transmitting 1DM/DMM PDU can be enabled/disabled.
Delay Measurement based on receiving and handling 1DM/DMR PDU is always enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.13.1.1.1 |
tnEthSoamDmCfgPriorityThe priority to be inserted as PCP bits in TAG (if any).rw IEEE8021PriorityValue (IEEE8021-TC-MIB) .1.3.6.1.4.1.7483.6.105.1.13.1.1.2 |
tnEthSoamDmCfgCastSelection of 1DM/DMM PDU transmitted unicast or multicast.
The unicast MAC will be configured through 'Peer MEP'.rw Enumeration .1.3.6.1.4.1.7483.6.105.1.13.1.1.3 |
tnEthSoamDmCfgPeerIdPeer MEP ID.rw Dot1agCfmMepId .1.3.6.1.4.1.7483.6.105.1.13.1.1.4 |
tnEthSoamDmCfgWayTypeOne-Way: One-Way Delay Measurement implemented on 1DM.
Two-Way: Two-Way Delay Measurement implemented on DMM/DMR.rw Enumeration .1.3.6.1.4.1.7483.6.105.1.13.1.1.5 |
tnEthSoamDmCfgTxModeStandardize: Y.1731 standardize way to transmit 1DM/DMR.
Proprietary: Vitesse proprietary way with follow-up packets to transmit 1DM/DMR.rw Enumeration .1.3.6.1.4.1.7483.6.105.1.13.1.1.6 |
tnEthSoamDmCfgCalcThis is only used if the 'Way' is configured to Two-way.
Round trip: The frame dealy calculated by the transmitting and receiving timestamps of initiators.
Frame Delay = RxTimeb-TxTimeStampf
Flow: The frame dealy calculated by the transmitting and receiving timestamps of initiators and remotes.
Frame Delay = (RxTimeb-TxTimeStampf)-(TxTimeStampb-RxTimeStampf).rw Enumeration .1.3.6.1.4.1.7483.6.105.1.13.1.1.7 |
tnEthSoamDmCfgGapThe gap between transmitting 1DM/DMM PDU in 10ms. The range is 10 to 65535.rw Unsigned32 .1.3.6.1.4.1.7483.6.105.1.13.1.1.8 |
tnEthSoamDmCfgCountThe number of last records to calculate. The range is 10 to 2000.rw INTEGER .1.3.6.1.4.1.7483.6.105.1.13.1.1.9 |
tnEthSoamDmCfgUnitThe time resolution.rw Enumeration .1.3.6.1.4.1.7483.6.105.1.13.1.1.10 |
tnEthSoamDmCfgD2forD1Enable to use DMM/DMR packet to calculate one-way DM. If the option is enabled, the following action will be taken.
When DMR is received, two-way delay (roundtrip or flow) and both near-end-to-far-end and far-end-to-near-end one-way delay are calcualted.
When DMM or 1DM is received, only far-end-to-near-end one-way delay is calculated.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.13.1.1.11 |
tnEthSoamDmCfgCOActionThe action to counter when overflow happens.rw Enumeration .1.3.6.1.4.1.7483.6.105.1.13.1.1.12 |
tnEthSoamDmStateMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.105.1.14 |
tnEthSoamDmStateTableThis table has entries which generate a configuration for delay measurement state. SEQUENCE OF TnEthSoamDmStateEntry .1.3.6.1.4.1.7483.6.105.1.14.1 |
tnEthSoamDmStateEntryA entry in the table which generate a configuration for delay measurement state. TnEthSoamDmStateEntry .1.3.6.1.4.1.7483.6.105.1.14.1.1 |
tnEthSoamDmStateFNTxCountThe accumulated transmit count - since last 'clear'.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.1 |
tnEthSoamDmStateFNRxTimeoutThe accumulated receive timeout count for two-way only - since last 'clear'.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.2 |
tnEthSoamDmStateFNRxCountThe accumulated receive count - since last 'clear'.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.3 |
tnEthSoamDmStateFNRxErrorThe accumulated receive error count - since last 'clear'. The frame delay is larger than 1 second(timeout).ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.4 |
tnEthSoamDmStateFNAvgTotalThe average delay - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.5 |
tnEthSoamDmStateFNAvgLastNThe average delay of the last n packets - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.6 |
tnEthSoamDmStateFNAvgVarTotalThe average delay variation - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.7 |
tnEthSoamDmStateFNAvgVarLastNThe average delay variation of the last n packets - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.8 |
tnEthSoamDmStateFNMinValueThe minimum delay - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.9 |
tnEthSoamDmStateFNMaxValueThe maximum delay - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.10 |
tnEthSoamDmStateFNOverFlowThe number of counter overflow - since last 'clear'.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.11 |
tnEthSoamDmStateNFTxCountThe accumulated transmit count - since last 'clear'.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.12 |
tnEthSoamDmStateNFRxTimeoutThe accumulated receive timeout count for two-way only - since last 'clear'.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.13 |
tnEthSoamDmStateNFRxCountThe accumulated receive count - since last 'clear'.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.14 |
tnEthSoamDmStateNFRxErrorThe accumulated receive error count - since last 'clear'. The frame delay is larger than 1 second(timeout).ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.15 |
tnEthSoamDmStateNFAvgTotalThe average delay - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.16 |
tnEthSoamDmStateNFAvgLastNThe average delay of the last n packets - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.17 |
tnEthSoamDmStateNFAvgVarTotalThe average delay variation - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.18 |
tnEthSoamDmStateNFAvgVarLastNThe average delay variation of the last n packets - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.19 |
tnEthSoamDmStateNFMinValueThe minimum delay - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.20 |
tnEthSoamDmStateNFMaxValueThe maximum delay - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.21 |
tnEthSoamDmStateNFOverFlowThe number of counter overflow - since last 'clear'.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.22 |
tnEthSoamDmStateTwoWayTxCountThe accumulated transmit count - since last 'clear'.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.23 |
tnEthSoamDmStateTwoWayRxTimeoutThe accumulated receive timeout count for two-way only - since last 'clear'.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.24 |
tnEthSoamDmStateTwoWayRxCountThe accumulated receive count - since last 'clear'.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.25 |
tnEthSoamDmStateTwoWayRxErrorThe accumulated receive error count - since last 'clear'. The frame delay is larger than 1 second(timeout).ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.26 |
tnEthSoamDmStateTwoWayAvgTotalThe average delay - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.27 |
tnEthSoamDmStateTwoWayAvgLastNThe average delay of the last n packets - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.28 |
tnEthSoamDmStateTwoWayAvgVarTotalThe average delay variation - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.29 |
tnEthSoamDmStateTwoWayAvgVarLastNThe average delay variation of the last n packets - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.30 |
tnEthSoamDmStateTwoWayMinValueThe minimum delay - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.31 |
tnEthSoamDmStateTwoWayMaxValueThe maximum delay - since last 'clear'. The unit is microsecond.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.32 |
tnEthSoamDmStateTwoWayOverFlowThe number of counter overflow - since last 'clear'.ro Gauge32 .1.3.6.1.4.1.7483.6.105.1.14.1.1.33 |
tnEthSoamDmStateActionThe number of counter overflow - since last 'clear'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7483.6.105.1.14.1.1.34 |
tnEthSoamMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.7483.6.105.2 |