SYMMCOMMONNETWORK
This is the Symmetricom Common MIB for Ethernet and IP configuration and status. It has three main nodes: 1. Ethernet configuration 2. IP configuration and status (including routing and firewall) 3. VLAN configuration
Main OID:
symmCommonNetwork.1.3.6.1.4.1.9070.1.2.5.4.1
101
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
101 total| Object Name |
|---|
symmCommonNetworkThis is the Symmetricom Common MIB for Ethernet and IP configuration and status. It has three main nodes: 1. Ethernet configuration 2. IP configuration and status (including routing and firewall) 3. VLAN configuration MODULE-IDENTITY .1.3.6.1.4.1.9070.1.2.5.4.1 |
networkEthStatus OBJECT IDENTIFIER .1.3.6.1.4.1.9070.1.2.5.4.1.1 |
networkEthLinkTableThe Ethernet port link table of the TP5000 device. SEQUENCE OF NetworkEthLinkEntry .1.3.6.1.4.1.9070.1.2.5.4.1.1.1 |
networkEthLinkEntryThe ethernet link table. NetworkEthLinkEntry .1.3.6.1.4.1.9070.1.2.5.4.1.1.1.1 |
networkEthLinkIndexThe index of ethernet link table. Integer32 .1.3.6.1.4.1.9070.1.2.5.4.1.1.1.1.1 |
networkEthLinkSpeedThe ethernet auto-negotiation speed. The defined speeds are 100M, 1000M, or nonero ETHAUTOSPEEDTYPE .1.3.6.1.4.1.9070.1.2.5.4.1.1.1.1.2 |
networkEthLinkStatusEth port link status, UP or DOWNro ETHLINK .1.3.6.1.4.1.9070.1.2.5.4.1.1.1.1.3 |
networkEthConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9070.1.2.5.4.1.2 |
networkEthAutoNegTableEthernet port auto-negotiation table for common network. SEQUENCE OF NetworkEthAutoNegEntry .1.3.6.1.4.1.9070.1.2.5.4.1.2.1 |
networkEthAutoNegEntryAn entry of Ethernet port auto-negotiation table. Table index is ifIndex (port/interface index). NetworkEthAutoNegEntry .1.3.6.1.4.1.9070.1.2.5.4.1.2.1.1 |
networkEthAutoNegIndexLocal index of the Ethernet port auto-negotiation table. Integer32 .1.3.6.1.4.1.9070.1.2.5.4.1.2.1.1.1 |
networkEthAutoNegStateEthernet port auto-negotiation state can be Enable (1) or Disable (2).rw EnableValue .1.3.6.1.4.1.9070.1.2.5.4.1.2.1.1.2 |
networkEthAutoNegSpeedAdvertised speed for Ethernet port auto-negotiation. Its value can be 100M, 1000M, or All.rw AutoSpeedValue .1.3.6.1.4.1.9070.1.2.5.4.1.2.1.1.3 |
networkIpConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9070.1.2.5.4.1.3 |
networkIPv4ConfigTableIPv4 interface configuration table for common network. It is used to read or write the IP address of the specified interface. SEQUENCE OF NetworkIPv4ConfigEntry .1.3.6.1.4.1.9070.1.2.5.4.1.3.1 |
networkIPv4ConfigEntryAn entry of the IPv4 interface configuration table. Table index is ifIndex (port/interface index). NetworkIPv4ConfigEntry .1.3.6.1.4.1.9070.1.2.5.4.1.3.1.1 |
networkIPv4ConfigIndexIPv4 Local Index Integer32 .1.3.6.1.4.1.9070.1.2.5.4.1.3.1.1.1 |
networkIPv4AddressOriginThe origin of this IPv4 address can be one of the following: -manual(2) indicates that the address was manually configured to a specified address, e.g., by user configuration. -dhcp(4) indicates an address that was assigned to this system by a DHCP server. -linklayer(5) indicates an address created by IPv6 stateless auto-configuration. -random(6) indicates an address chosen by the system at random, e.g., an IPv4 address within 169.254/16, or an RFC 3041 privacy address. See existing object descriptionrw IpAddressOriginTC .1.3.6.1.4.1.9070.1.2.5.4.1.3.1.1.2 |
networkIPv4AddressThe IP address to which this entry's addressing information pertains. Implementers need to be aware that if the size ipAddressAddr exceeds 116 octets, then OIDS of instances of columns in this row will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3rw IpAddress .1.3.6.1.4.1.9070.1.2.5.4.1.3.1.1.3 |
networkIPv4DefaultRouteAddrThe IP address of the default router represented by this row. The address type of this object is specified in symmIPAddressType. Implementers need to be aware that if the size of ipDefaultRouterAddress exceeds 115 octets, then OIDS of instances of columns in this row will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3.rw IpAddress .1.3.6.1.4.1.9070.1.2.5.4.1.3.1.1.4 |
networkIPv4SubnetMaskThe mask of an IPv4 interface. The address format is : xxx.xxx.xxx.xxx.rw IpAddress .1.3.6.1.4.1.9070.1.2.5.4.1.3.1.1.5 |
networkIPv4PortStateThe IP interface state can be Enable (1) or Disable (2).rw IPPortStateValue .1.3.6.1.4.1.9070.1.2.5.4.1.3.1.1.6 |
networkIPv4StaticRouteTableThe static route table is dynamic; its number of entries is not fixed. It is used to read or create a static route for the specified interface. SEQUENCE OF NetworkIPv4StaticRouteEntry .1.3.6.1.4.1.9070.1.2.5.4.1.3.2 |
networkIPv4StaticRouteEntryAn entry of the IPv4 static route table. Table index is a double index: ifIndex and the local index networkIPv4StaticRouteIndex. NetworkIPv4StaticRouteEntry .1.3.6.1.4.1.9070.1.2.5.4.1.3.2.1 |
networkIPv4StaticRouteIndexLocal index of the static route table.ro Integer32 .1.3.6.1.4.1.9070.1.2.5.4.1.3.2.1.1 |
networkIPv4StaticRouteIfindexIfIndex of the static route table.rw Integer32 .1.3.6.1.4.1.9070.1.2.5.4.1.3.2.1.2 |
networkIPv4StaticDestAddrThe destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.rw IpAddress .1.3.6.1.4.1.9070.1.2.5.4.1.3.2.1.3 |
networkIPv4StaticRouteMaskIndicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the ipRouteMask by determining whether the value of the correspondent ipRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the ipRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.rw IpAddress .1.3.6.1.4.1.9070.1.2.5.4.1.3.2.1.4 |
networkIPv4StaticRouteNextHopThe IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface.)rw IpAddress .1.3.6.1.4.1.9070.1.2.5.4.1.3.2.1.5 |
networkIPv4StaticRouteMetric1The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.rw INTEGER (-1..65534) .1.3.6.1.4.1.9070.1.2.5.4.1.3.2.1.6 |
networkIPv4StaticRouteRowStatusThe row status of the IPv4 static route table is used to control row action. It has six defined action values: - `active(1)', which indicates that the conceptual row is available for use by the managed device; - `notInService(2)', which indicates that the conceptual row exists in the agent, but it is unavailable for use by the managed device; - `notReady(3)', which indicates that the conceptual row exists in the agent, but it does not have all information necessary for the row to be available for use by the managed device; - `createAndGo(4)', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - `createAndWait(5)', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by managed device); and, - `destroy(6)', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9070.1.2.5.4.1.3.2.1.7 |
networkFirewallTableThis is the firewall configuration table for TP5000 external management port on the main shelf IMC module. SEQUENCE OF NetworkFirewallEntry .1.3.6.1.4.1.9070.1.2.5.4.1.3.3 |
networkFirewallEntryAn entry of the firewall configuration table. Table index is ifIndex. NetworkFirewallEntry .1.3.6.1.4.1.9070.1.2.5.4.1.3.3.1 |
networkFirewallIndexLocal index of the port Firewall table. Integer32 .1.3.6.1.4.1.9070.1.2.5.4.1.3.3.1.1 |
networkFirewallICMPFirewall control for ICMP. Value is Allow (1) or Block (2).rw FirewallOnOff .1.3.6.1.4.1.9070.1.2.5.4.1.3.3.1.2 |
networkFirewallTelnetFirewall control for Telnet. Value is Allow (1) or Block (2).rw FirewallOnOff .1.3.6.1.4.1.9070.1.2.5.4.1.3.3.1.3 |
networkFirewallSSHFirewall control for SSH. Value is Allow (1) or Block (2).rw FirewallOnOff .1.3.6.1.4.1.9070.1.2.5.4.1.3.3.1.4 |
networkFirewallSFTPFirewall control for SFTP. Value is Allow (1) or Block (2).rw FirewallOnOff .1.3.6.1.4.1.9070.1.2.5.4.1.3.3.1.5 |
networkFirewallSNMPFirewall control for SNMP. Value is Allow (1) or Block (2).rw FirewallOnOff .1.3.6.1.4.1.9070.1.2.5.4.1.3.3.1.6 |
networkFirewallFTPFirewall control for FTP. Value is Allow (1) or Block (2).rw FirewallOnOff .1.3.6.1.4.1.9070.1.2.5.4.1.3.3.1.7 |
networkFirewallNTPFirewall control for NTP. Value is Allow (1) or Block (2).rw FirewallOnOff .1.3.6.1.4.1.9070.1.2.5.4.1.3.3.1.8 |
networkIPv6ConfigTableDescription. SEQUENCE OF NetworkIPv6ConfigEntry .1.3.6.1.4.1.9070.1.2.5.4.1.3.4 |
networkIPv6ConfigEntryDescription. NetworkIPv6ConfigEntry .1.3.6.1.4.1.9070.1.2.5.4.1.3.4.1 |
networkIPv6ConfigIndexDescription. Integer32 .1.3.6.1.4.1.9070.1.2.5.4.1.3.4.1.1 |
networkIPv6AddressOriginThe origin of this IPV6 addressrw IpAddressOriginTC .1.3.6.1.4.1.9070.1.2.5.4.1.3.4.1.2 |
networkIPv6AddressThe IPV6 address to which this entry's addressing information pertainsrw InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9070.1.2.5.4.1.3.4.1.3 |
networkIPv6PrefixPrefix of IPv6rw Integer32 .1.3.6.1.4.1.9070.1.2.5.4.1.3.4.1.4 |
networkIPv6DefaultRouteAddrThe IPv6 default router address. Format 2x:2x:2x:2x:2x:2x:2x:2xrw InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9070.1.2.5.4.1.3.4.1.5 |
networkIPv6PortStateThe IP interface state can be Enable(1) or Disable(2)rw IPPortStateValue .1.3.6.1.4.1.9070.1.2.5.4.1.3.4.1.6 |
networkIPv6StaticRouteTableDescription. SEQUENCE OF NetworkIPv6StaticRouteEntry .1.3.6.1.4.1.9070.1.2.5.4.1.3.5 |
networkIPv6StaticRouteEntryDescription. NetworkIPv6StaticRouteEntry .1.3.6.1.4.1.9070.1.2.5.4.1.3.5.1 |
networkIPv6StaticRouteIndexDescription.ro Integer32 .1.3.6.1.4.1.9070.1.2.5.4.1.3.5.1.1 |
networkIPv6StaticRouteIfindexDescription.rw Integer32 .1.3.6.1.4.1.9070.1.2.5.4.1.3.5.1.2 |
networkIPv6StaticRouteDestAddrThe destination IP address of this routerw InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9070.1.2.5.4.1.3.5.1.3 |
networkIPv6StaticRoutePrefixDescriptionrw Integer32 .1.3.6.1.4.1.9070.1.2.5.4.1.3.5.1.4 |
networkIPv6StaticRouteNextHopThe IPv6 address of the next hop of this route.rw InetAddressIPv6z (INET-ADDRESS-MIB) .1.3.6.1.4.1.9070.1.2.5.4.1.3.5.1.5 |
networkIPv6StaticRouteMetric1The Primary routing metric for this route. The semantics of this metric are determined by the routing protocal specified in the route's ipRouteProto value.rw INTEGER (-1..65534) .1.3.6.1.4.1.9070.1.2.5.4.1.3.5.1.6 |
networkIPv6StaticRouteRowStatusThe row status of the IPv6 static route table is used to control row action It has six defined action values - active(1) - notInService(2) - notReady(3) - createAndGo(4) - createAndWait(5) - destroy(6)rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9070.1.2.5.4.1.3.5.1.7 |
networkIPVerTableIP version of available interfaces SEQUENCE OF NetworkIPVerEntry .1.3.6.1.4.1.9070.1.2.5.4.1.3.6 |
networkIPVerEntryDescription. NetworkIPVerEntry .1.3.6.1.4.1.9070.1.2.5.4.1.3.6.1 |
networkIPVerIndexDescription. Integer32 .1.3.6.1.4.1.9070.1.2.5.4.1.3.6.1.1 |
networkIPVersionIP version of this interfacerw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9070.1.2.5.4.1.3.6.1.2 |
networkIPv6AutoConfigTableDescription. SEQUENCE OF NetworkIPv6AutoConfigEntry .1.3.6.1.4.1.9070.1.2.5.4.1.3.7 |
networkIPv6AutoConfigEntryDescription. NetworkIPv6AutoConfigEntry .1.3.6.1.4.1.9070.1.2.5.4.1.3.7.1 |
networkIPv6AutoConfigIndexDescription. Integer32 (1) .1.3.6.1.4.1.9070.1.2.5.4.1.3.7.1.1 |
networkIPv6AutoConfigModeDescription.rw EnableValue .1.3.6.1.4.1.9070.1.2.5.4.1.3.7.1.2 |
networkVlanConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9070.1.2.5.4.1.4 |
networkIPStatus OBJECT IDENTIFIER .1.3.6.1.4.1.9070.1.2.5.4.1.5 |
networkIPv4StatusTableDescription. SEQUENCE OF NetworkIPv4StatusEntry .1.3.6.1.4.1.9070.1.2.5.4.1.5.1 |
networkIPv4StatusEntryDescription. NetworkIPv4StatusEntry .1.3.6.1.4.1.9070.1.2.5.4.1.5.1.1 |
networkIPv4StatusIndexDescription. Integer32 .1.3.6.1.4.1.9070.1.2.5.4.1.5.1.1.1 |
networkIPv4ModuleDescription.ro TPMODULEID .1.3.6.1.4.1.9070.1.2.5.4.1.5.1.1.2 |
networkIPv4VlanIDDescription.ro Integer32 .1.3.6.1.4.1.9070.1.2.5.4.1.5.1.1.3 |
networkIPv4AddrDescription.ro InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9070.1.2.5.4.1.5.1.1.4 |
networkIPv4NetmaskDescription.ro InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9070.1.2.5.4.1.5.1.1.5 |
networkIPv4RouteAddrDescription.ro InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9070.1.2.5.4.1.5.1.1.6 |
networkIPv4ModeThe origin of this IPv4 address can be one of the following: -manual(2) indicates that the address was manually configured to a specified address, e.g., by user configuration. -dhcp(4) indicates an address that was assigned to this system by a DHCP server. -linklayer(5) indicates an address created by IPv6 stateless auto-configuration. -random(6) indicates an address chosen by the system at random, e.g., an IPv4 address within 169.254/16, or an RFC 3041 privacy address. See existing object descriptionro IpAddressOriginTC .1.3.6.1.4.1.9070.1.2.5.4.1.5.1.1.7 |
networkIPv6StatusTableDescription. SEQUENCE OF NetworkIPv6StatusEntry .1.3.6.1.4.1.9070.1.2.5.4.1.5.2 |
networkIPv6StatusEntryDescription. NetworkIPv6StatusEntry .1.3.6.1.4.1.9070.1.2.5.4.1.5.2.1 |
networkIPv6StatusIndexDescription. Integer32 .1.3.6.1.4.1.9070.1.2.5.4.1.5.2.1.1 |
networkIPv6ModuleDescription.ro TPMODULEID .1.3.6.1.4.1.9070.1.2.5.4.1.5.2.1.2 |
networkIPv6VlanIDDescription.ro Integer32 .1.3.6.1.4.1.9070.1.2.5.4.1.5.2.1.3 |
networkIPv6AddrDescription.ro InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9070.1.2.5.4.1.5.2.1.4 |
networkIPv6PrefixLengthDescription.ro InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.9070.1.2.5.4.1.5.2.1.5 |
networkIPv6AddrScopeDescription.ro IPV6SCOPE .1.3.6.1.4.1.9070.1.2.5.4.1.5.2.1.6 |
networkIPv6ModeDescription.ro IpAddressOriginTC .1.3.6.1.4.1.9070.1.2.5.4.1.5.2.1.7 |
networkConformanceThis subtree contains conformance statements for the SYMMETRICOM-LED-MIB module. OBJECT IDENTIFIER .1.3.6.1.4.1.9070.1.2.5.4.1.6 |
networkCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9070.1.2.5.4.1.6.1 |
networkBasicComplianceThe compliance statement for SNMP entities which have common network of symmetricom. Unknown .1.3.6.1.4.1.9070.1.2.5.4.1.6.1.1 |
networkUocGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9070.1.2.5.4.1.6.2 |
networkEthAutoNetGroupA collection of objects providing information applicable to ethernet auto-negotiation configuration group. Unknown .1.3.6.1.4.1.9070.1.2.5.4.1.6.2.1 |
networkIPv4ConfigGroupA collection of objects providing information applicable to IP configuration group. Unknown .1.3.6.1.4.1.9070.1.2.5.4.1.6.2.2 |
networkFirewallGroupA collection of objects providing information applicable to firewall group. Unknown .1.3.6.1.4.1.9070.1.2.5.4.1.6.2.3 |
networkIPv4StaticRouteGroupDescription. Unknown .1.3.6.1.4.1.9070.1.2.5.4.1.6.2.4 |
networkEthStatusGroupDescription. Unknown .1.3.6.1.4.1.9070.1.2.5.4.1.6.2.5 |
networkIPv6ConfigGroupDescription. Unknown .1.3.6.1.4.1.9070.1.2.5.4.1.6.2.6 |
networkIPv6StaticRouteGroupDescription. Unknown .1.3.6.1.4.1.9070.1.2.5.4.1.6.2.7 |
networkIPVersionGroupDescription. Unknown .1.3.6.1.4.1.9070.1.2.5.4.1.6.2.8 |
networkIPv6AutoConfigGroupDescription. Unknown .1.3.6.1.4.1.9070.1.2.5.4.1.6.2.9 |
networkIPv4StatusGroupDescription. Unknown .1.3.6.1.4.1.9070.1.2.5.4.1.6.2.10 |
networkIPv6StatusGroupDescription. Unknown .1.3.6.1.4.1.9070.1.2.5.4.1.6.2.11 |