SW-MIB
AI MIB Summary
SW-MIB provides management and monitoring capabilities for Brocade Fibre Channel switches, exposing critical operational metrics such as port status, traffic counters, buffer credits, and fabric topology state. This module enables the collection of performance data and fault detection for storage area network (SAN) infrastructure via SNMP.
The MIB module is for Brocade's Fibre Channel Switch. Copyright (c) 1996-2003 Brocade Communications Systems, Inc. All rights reserved.
Main OID:
swMibModule.1.3.6.1.4.1.1588.3.1.3
248
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
248 total| Object Name |
|---|
swThe OID sub-tree for Brocade's Silkworm Series of Fibre Channel Switches. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1 |
swTrapsV2The Traps for Brocade's Fibre Channel Switch. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1.0 |
swFaultObsoleted this trap as firmware doesn't support this trap. A swFault(1) is generated whenever the diagnostics detects a fault with the switch.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.1588.2.1.1.1.0.1 |
swSensorScnA swSensorScn(2) is generated whenever an environment sensor changes its operational state. For instance, a fan stop working. The VarBind in the Trap Data Unit shall contain the corresponding instance of the sensor status, sensor index, sensor type, sensor value (reading) and sensor information. Note that the sensor information contains the type of sensor and its number in textual format. NOTIFICATION-TYPE .1.3.6.1.4.1.1588.2.1.1.1.0.2 |
swFCPortScnA swFCPortScn(3) is generated whenever an FC_Port changes its operational state. For instance, the FC_Port goes from on-line to offline. The VarBind in the Trap Data Unit shall contain the corresponding instance of the FC_Port's operational status, index, swFCPortName and swSsn. swFCPortName, swSsn are optional. NOTIFICATION-TYPE .1.3.6.1.4.1.1588.2.1.1.1.0.3 |
swEventTrapThis trap is generated when an event whose level at or below swEventTrapLevel occurs. NOTIFICATION-TYPE .1.3.6.1.4.1.1588.2.1.1.1.0.4 |
swFabricWatchTraptrap to be sent by Fabric Watch to notify of an event NOTIFICATION-TYPE .1.3.6.1.4.1.1588.2.1.1.1.0.5 |
swTrackChangesTraptrap to be sent for tracking login/logout/config changes NOTIFICATION-TYPE .1.3.6.1.4.1.1588.2.1.1.1.0.6 |
swSystemThe OID sub-tree for swSystem group. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1.1 |
swCurrentDateThe current date information in displayable textual format.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.1 |
swBootDateThe date and time when the system last booted, in displayable textual format.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.2 |
swFWLastUpdatedThe information indicates the date when the firmware was last updated, in displayable textual format.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.3 |
swFlashLastUpdatedThe information indicates the date when the FLASH was last updated, in displayable textual format.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.4 |
swBootPromLastUpdatedThe information indicates the date when the boot PROM was last updated, in displayable textual format.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.5 |
swFirmwareVersionThe current version of the firwmare.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.6 |
swOperStatusThe current operational status of the switch. The states are as follow: o online(1) means the switch is accessible by an external Fibre Channel port; o offline(2) means the switch is not accessible; o testing(3) means the switch is in a built-in test mode and is not accessible by an external Fibre Channel port; o faulty(4) means the switch is not operational.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.7 |
swAdmStatusThe desired administrative status of the switch. A management station may place the switch in a desired state by setting this object accordingly. The states are as follow: o online(1) means set the switch to be accessible by an external Fibre Channel port; o offline(2) means set the switch to be inaccessible; o testing(3) means set the switch to run the built-in test; o faulty(4) means set the switch to a 'soft' faulty condition; o reboot(5) means set the switch to reboot in 1 second. o fastboot(6) means set the switch to fastboot in 1 second. Fastboot would cause the switch to boot but skip over the POST. o switchReboot(7) means set the current switch to reboot in 1 second. When the switch is in faulty state, only two states can be set: faulty and reboot/fastboot/switchReboot.rw Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.8 |
swTelnetShellAdmStatusThe desired administrative status of the Telnet shell. By setting it to terminated(1), the current Telnet shell task is deleted. When this variable instance is read, it reports the value last set through SNMP.rw Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.9 |
swSsnThe soft serial number of the switch.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.10 |
swFlashDLOperStatusThe operational status of the FLASH. The operational states are as follow: o swCurrent(1) indicates that the FLASH contains the current firmware image or config file; o swFwUpgraded(2) state indicates that it contains the image upgraded from the swFlashDLHost.0.; o swCfUploaded(3) state indicates that the switch configuration file has been uploaded to the host; and o swCfDownloaded(4) state indicates that the switch configuration file has been downloaded from the host. o swFwCorrupted (5) state indicates that the firmware in the FLASH of the switch is corrupted.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.11 |
swFlashDLAdmStatusThe desired state of the FLASH. A management station may place the FLASH in a desired state by setting this object accordingly: o swCurrent(1) indicates that the FLASH contains the current firmware image or config file; o swFwUpgrade(2) means that the firmware in the FLASH is to be upgraded from the host specified; o swCfUpload(3) means that the switch config file is to be uploaded to the host specified; or o swCfDownload(4) means that the switch config file is to be downloaded from the host specified. o swFwCorrupted(5) state indicates that the firmware in the FLASH is corrupted. This value is for informational purpose only. However, set of swFlashDLAdmStatus to this value is not allowed. The host is specified in swFlashDLHost.0. In addition, user name is specified in swFlashDLUser.0, and the file name specified in swFlashDLFile.0. Reference the user manual on the following commands, o firmwareDownload, o configUpload, and o configDownload.rw Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.12 |
swFlashDLHostThe name or IP address (in dot notation) of the host to download or upload a relevant file to the FLASH.rw DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.13 |
swFlashDLUserThe user name on the host to download or upload a relevant file to or from the FLASH.rw DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.14 |
swFlashDLFileThe name of the file to be downloaded or uploaded.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1588.2.1.1.1.1.15 |
swFlashDLPasswordThe password to be used in for FTP transfer of files in the download or upload operation.rw DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.16 |
swBeaconOperStatusThe current operational status of the switch beacon. When the beacon is on, the LEDs on the front panel of the switch run alternately from left to right and right to left. The color is yellow. When the beacon is off, each LED will be in their its regular status indicating color and state.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.18 |
swBeaconAdmStatusThe desired status of the switch beacon. When the beacon is set to on, the LEDs on the front panel of the switch run alternately from left to right and right to left. The color is yellow. When the beacon is set to off, each LED will be in its regular status indicating color and state.rw Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.19 |
swDiagResultThe result of the power-on startup (POST) diagnostics.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.20 |
swNumSensorsThe number of sensors inside the switch.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.1.21 |
swSensorTableThe table of sensor entries. SEQUENCE OF SwSensorEntry .1.3.6.1.4.1.1588.2.1.1.1.1.22 |
swSensorEntryAn entry of the sensor information. SwSensorEntry .1.3.6.1.4.1.1588.2.1.1.1.1.22.1 |
swSensorIndexThis object identifies the sensor.ro SwSensorIndex (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.1.22.1.1 |
swSensorTypeThis object identifies the sensor type.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.22.1.2 |
swSensorStatusThe current status of the sensor.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.22.1.3 |
swSensorValueThe current value (reading) of the sensor. The value, -2147483648, represents an unknown quantity. It also means that the sensor does not have the capability to measure the actual value. In V2.0, the temperature sensor value will be in Celsius; the fan value will be in RPM (revolution per minute); and the power supply sensor reading will be unknown.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.1.22.1.4 |
swSensorInfoAdditional displayable information on the sensor. In V2.x, it contains the sensor type and number in textual format. For example, 'Temp 3', 'Fan 6'.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.22.1.5 |
swTrackChangesInfoTrack changes string. For trap onlyro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1588.2.1.1.1.1.23 |
swIDThe number of the logical switch (0/1)ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.1.24 |
swEtherIPAddressThe IP Address of the Ethernet interface of this logical switch.ro IpAddress .1.3.6.1.4.1.1588.2.1.1.1.1.25 |
swEtherIPMaskThe IP Mask of the Ethernet interface of this logical switch.ro IpAddress .1.3.6.1.4.1.1588.2.1.1.1.1.26 |
swFCIPAddressThe IP Address of the FC interface of this logical switch.ro IpAddress .1.3.6.1.4.1.1588.2.1.1.1.1.27 |
swFCIPMaskThe IP Mask of the FC interface of this logical switch.ro IpAddress .1.3.6.1.4.1.1588.2.1.1.1.1.28 |
swFabricThe OID sub-tree for swFabric group. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1.2 |
swDomainIDThe current Fibre Channel domain ID of the switch. To set a new value, the switch (swAdmStatus) must be in offline or testing state.rw SwDomainIndex (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.2.1 |
swPrincipalSwitchThis object indicates whether the switch is the Principal switch as per FC-SW.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.2.2 |
swNumNbsThe number of Inter-Switch Links in the (immediate) neighborhood.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.2.8 |
swNbTableThis table contains the ISLs in the immediate neighborhood of the switch. SEQUENCE OF SwNbEntry .1.3.6.1.4.1.1588.2.1.1.1.2.9 |
swNbEntryAn entry containing each neighbor ISL parameters. SwNbEntry .1.3.6.1.4.1.1588.2.1.1.1.2.9.1 |
swNbIndexThis object identifies the neighbor ISL entry.ro SwNbIndex (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.2.9.1.1 |
swNbMyPortThis is the port that has an ISL to another switch.ro SwPortIndex (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.2.9.1.2 |
swNbRemDomainThis is the Fibre Channel domain on the other end of the ISL.ro SwDomainIndex (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.2.9.1.3 |
swNbRemPortThis is the port index on the other end of the ISL.ro SwPortIndex (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.2.9.1.4 |
swNbBaudRateThe baud rate of the ISL.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.2.9.1.5 |
swNbIslStateThe current state of the ISL.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.2.9.1.6 |
swNbIslCostThe current link cost of the ISL.rw Integer32 .1.3.6.1.4.1.1588.2.1.1.1.2.9.1.7 |
swNbRemPortNameThe World_wide_Name of the remote port.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.2.9.1.8 |
swFabricMemTableThis table contains information on the member switches of a fabric. This may not be available on all versions of Fabric OS. SEQUENCE OF SwFabricMemEntry .1.3.6.1.4.1.1588.2.1.1.1.2.10 |
swFabricMemEntryAn entry containing each switch in the fabric. SwFabricMemEntry .1.3.6.1.4.1.1588.2.1.1.1.2.10.1 |
swFabricMemWwnThis object identifies the World wide name of the member switch.ro FcWwn (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.2.10.1.1 |
swFabricMemDidThis object identifies the domain id of the member switch.ro SwDomainIndex (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.2.10.1.2 |
swFabricMemNameThis object identifies the name of the member switch.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.2.10.1.3 |
swFabricMemEIPThis object identifies the ethernet IP address of the member switch.ro IpAddress .1.3.6.1.4.1.1588.2.1.1.1.2.10.1.4 |
swFabricMemFCIPThis object identifies the Fibre Channel IP address of the member switch.ro IpAddress .1.3.6.1.4.1.1588.2.1.1.1.2.10.1.5 |
swFabricMemGWIPThis object identifies the Gateway IP address of the member switch.ro IpAddress .1.3.6.1.4.1.1588.2.1.1.1.2.10.1.6 |
swFabricMemTypeThis object identifies the member switch type.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.2.10.1.7 |
swFabricMemShortVersionThis object identifies Fabric OS version of the member switch.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.2.10.1.8 |
swIDIDModeStatus of Insistent Domain ID (IDID) mode. Status indicating IDID mode is enabled or not.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.2.11 |
swModuleThe OID sub-tree for swModule group. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1.3 |
swAgtCfgThe OID sub-tree for swAgtCfg group. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1.4 |
swAgtCmtyTableA table that contains, one entry for each Community, the access control and parameters of the Community. SEQUENCE OF SwAgtCmtyEntry .1.3.6.1.4.1.1588.2.1.1.1.4.11 |
swAgtCmtyEntryAn entry containing the Community parameters. SwAgtCmtyEntry .1.3.6.1.4.1.1588.2.1.1.1.4.11.1 |
swAgtCmtyIdxThis object identifies the SNMPv1 Community entry.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.4.11.1.1 |
swAgtCmtyStrThis is a Community string supported by the agent. If a new value is set successfully, it takes effect immediately.rw DisplayString .1.3.6.1.4.1.1588.2.1.1.1.4.11.1.2 |
swAgtTrapRcpThis is the trap recipient associated with the Community. If a new value is set successfully, it takes effect immediately.rw IpAddress .1.3.6.1.4.1.1588.2.1.1.1.4.11.1.3 |
swAgtTrapSeverityLevelThis is the trap severity level associated with the swAgtTrapRcp. The trap severity level in conjunction with the an event's severity level. When an event occurs and if its severity level is at or below the set value, the SNMP trap is sent to configured trap recipients. The severity level is limited to particular events. If a new value is set successfully, it takes effect immediately.rw SwSevType .1.3.6.1.4.1.1588.2.1.1.1.4.11.1.4 |
swFCportThe OID sub-tree for swFCport group. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1.6 |
swFCPortCapacityThe maximum number of Fibre Channel ports on this switch. It includes G_Port, F_Port, FL_Port and any other types of Fibre Channel port.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.6.1 |
swFCPortTableA table that contains, one entry for each switch port, configuration and service parameters of the port. SEQUENCE OF SwFCPortEntry .1.3.6.1.4.1.1588.2.1.1.1.6.2 |
swFCPortEntryAn entry containing the configuration and service parameters of the switch port. SwFCPortEntry .1.3.6.1.4.1.1588.2.1.1.1.6.2.1 |
swFCPortIndexThis object identifies the switch port index. Note that the value of a port index is 1 higher than the port number labeled on the front panel. E.g. port index 1 correspond to port number 0.ro SwPortIndex (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.1 |
swFCPortTypeThis object identifies the type of switch port. It may be of type stitch(1), flannel(2), loom(3) , bloom(4),rdbloom(5) or wormhole(6).ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.2 |
swFCPortPhyStateThis object identifies the physical state of the port: noCard(1) no card present in this switch slot; noTransceiver(2) no Transceiver module in this port. noGbic(2) was used previously. Transceiver is the generic name for GBIC, SFP etc.; laserFault(3) the module is signaling a laser fault (defective Transceiver); noLight(4) the module is not receiving light; noSync(5) the module is receiving light but is out of sync; inSync(6) the module is receiving light and is in sync; portFault(7) the port is marked faulty (defective Transceiver, cable or device); diagFault(8) the port failed diagnostics (defective G_Port or FL_Port card or motherboard); lockRef(9) the port is locking to the reference signal.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.3 |
swFCPortOpStatusThis object identifies the operational status of the port. The online(1) state indicates that user frames can be passed. The unknown(0) state indicates that likely the port module is physically absent (see swFCPortPhyState).ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.4 |
swFCPortAdmStatusThe desired state of the port. A management station may place the port in a desired state by setting this object accordingly. The testing(3) state indicates that no user frames can be passed. As the result of either explicit management action or per configuration information accessible by the switch, swFCPortAdmStatus is then changed to either the online(1) or testing(3) states, or remains in the offline(2) state.rw Enumeration .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.5 |
swFCPortLinkStateThis object indicates the link state of the port. The value may be: enabled(1) - port is allowed to participate in the FC-PH protocol with its attached port (or ports if it is in a FC-AL loop); disabled(2) - the port is not allowed to participate in the FC-PH protocol with its attached port(s); loopback(3) - the port may transmit frames through an internal path to verify the health of the transmitter and receiver path. Note that when the port's link state changes, its operational status (swFCPortOpStatus) will be affected.rw Enumeration .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.6 |
swFCPortTxTypeThis object indicates the media transmitter type of the port. The value may be: unknown(1) cannot determined to the port driver lw(2) long wave laser sw(3) short wave laser ld(4) long wave LED cu(5) copper (electrical).ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.7 |
swFCPortTxWordsThis object counts the number of Fibre Channel words that the port has transmitted.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.11 |
swFCPortRxWordsThis object counts the number of Fibre Channel words that the port has received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.12 |
swFCPortTxFramesThis object counts the number of (Fibre Channel) frames that the port has transmitted.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.13 |
swFCPortRxFramesThis object counts the number of (Fibre Channel) frames that the port has received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.14 |
swFCPortRxC2FramesThis object counts the number of Class 2 frames that the port has received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.15 |
swFCPortRxC3FramesThis object counts the number of Class 3 frames that the port has received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.16 |
swFCPortRxLCsThis object counts the number of Link Control frames that the port has received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.17 |
swFCPortRxMcastsThis object counts the number of Multicast frames that the port has received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.18 |
swFCPortTooManyRdysThis object counts the number of times when RDYs exceeds the frames received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.19 |
swFCPortNoTxCreditsThis object counts the number of times when the transmit credit has reached zero.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.20 |
swFCPortRxEncInFrsThis object counts the number of encoding error or disparity error inside frames received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.21 |
swFCPortRxCrcsThis object counts the number of CRC errors detected for frames received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.22 |
swFCPortRxTruncsThis object counts the number of truncated frames that the port has received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.23 |
swFCPortRxTooLongsThis object counts the number of received frames that are too long.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.24 |
swFCPortRxBadEofsThis object counts the number of received frames that have bad EOF delimiter.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.25 |
swFCPortRxEncOutFrsThis object counts the number of encoding error or disparity error outside frames received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.26 |
swFCPortRxBadOsThis object counts the number of invalid Ordered Sets received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.27 |
swFCPortC3DiscardsThis object counts the number of Class 3 frames that the port has discarded.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.28 |
swFCPortMcastTimedOutsThis object counts the number of Multicast frames that has been timed out.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.29 |
swFCPortTxMcastsThis object counts the number of Multicast frames that has been transmitted.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.30 |
swFCPortLipInsThis object counts the number of Loop Initializations that has been initiated by loop devices attached.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.31 |
swFCPortLipOutsThis object counts the number of Loop Initializations that has been initiated by the port.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.32 |
swFCPortLipLastAlpaThis object indicates the Physical Address (AL_PA) of the loop device that initiated the last Loop Initialization.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.33 |
swFCPortWwnThe World_wide_Name of the Fibre Channel port. The contents of an instance are in the IEEE extended format as specified in FC-PH; the 12-bit port identifier represents the port number within the switch.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.34 |
swFCPortSpeedThe desired baud rate for the port. It can have the values of 1GB (1), 2GB (2), Auto-Negotiate (3) or 4GB (4). Some of the above values may not be supported by all type of switches.rw Enumeration .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.35 |
swFCPortNameA string indicates the name of the addressed port. The names should be persistent across switch reboots. Port names do not have to be unique within a switch or within a fabric.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.36 |
swFCPortSpecifierThis string indicates the physical port number of the addressed port. The format of the string is: <slot>/port, where 'slot' being present only for bladed systems.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.37 |
swNsThe OID sub-tree for swNs group. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1.7 |
swNsLocalNumEntryThe number of local Name Server entries.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.7.1 |
swNsLocalTableThe table of local Name Server entries. SEQUENCE OF SwNsEntry .1.3.6.1.4.1.1588.2.1.1.1.7.2 |
swNsLocalEntryAn entry of the local Name Server database. SwNsEntry .1.3.6.1.4.1.1588.2.1.1.1.7.2.1 |
swNsEntryIndexThe object identifies the Name Server database entry.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.7.2.1.1 |
swNsPortIDThe object identifies the Fibre Channel port address ID of the entry.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.7.2.1.2 |
swNsPortTypeThe object identifies the type of port: N_Port, NL_Port, etc., for this entry. The type is defined in FC-GS-2.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.7.2.1.3 |
swNsPortNameThe object identifies the Fibre Channel World_wide Name of the port entry.ro FcWwn (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.7.2.1.4 |
swNsPortSymbThe object identifies the contents of a Symbolic Name of the port entry. In FC-GS-2, a Symbolic Name consists of a byte array of 1 through 255 bytes, and the first byte of the array specifies the length of its 'contents'. This object variable corresponds to the 'contents' of the Symbolic Name, without the first byte.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.7.2.1.5 |
swNsNodeNameThe object identifies the Fibre Channel World_wide Name of the associated node as defined in FC-GS-2.ro FcWwn (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.7.2.1.6 |
swNsNodeSymbThe object identifies the contents of a Symbolic Name of the the node associated with the entry. In FC-GS-2, a Symbolic Name consists of a byte array of 1 through 255 bytes, and the first byte of the array specifies the length of its 'contents'. This object variable corresponds to the 'contents' of the Symbolic Name, without the first byte (specifying the length).ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.7.2.1.7 |
swNsIPAThe object identifies the Initial Process Associator of the node for the entry as defined in FC-GS-2.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.7.2.1.8 |
swNsIpAddressThe object identifies the IP address of the node for the entry as defined in FC-GS-2. The format of the address is in IPv6.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.7.2.1.9 |
swNsCosThe object identifies the class of services supported by the port. The value is a bit-map defined as follows: o bit 0 is class F, o bit 1 is class 1, o bit 2 is class 2, o bit 3 is class 3, o bit 4 is class 4, etc.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.7.2.1.10 |
swNsFc4The object identifies the FC-4s supported by the port as defined in FC-GS-2.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.7.2.1.11 |
swNsIpNxPortThe object identifies IpAddress of the Nx_port for the entry.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.7.2.1.12 |
swNsWwnThe object identifies the World Wide Name (WWN) of the Fx_port for the entry.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.7.2.1.13 |
swNsHardAddrThe object identifies the 24-bit hard address of the node for the entry.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.7.2.1.14 |
swEventThe OID sub-tree for swEvent group. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1.8 |
swEventTrapLevelswAgtTrapSeverityLevel, in absence of swEventTrapLevel, specifies the Trap Severity Level of each defined trap recipient host. This object specifies the swEventTrap level in conjunction with an event's severity level. When an event occurs and if its severity level is at or below the value specified by this object instance, the agent will send the associated swEventTrap to configured recipients.rwdeprecated Enumeration .1.3.6.1.4.1.1588.2.1.1.1.8.1 |
swEventNumEntriesThe number of entries in the Event Table.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.8.4 |
swEventTableThe table of event entries. SEQUENCE OF SwEventEntry .1.3.6.1.4.1.1588.2.1.1.1.8.5 |
swEventEntryAn entry of the event table. SwEventEntry .1.3.6.1.4.1.1588.2.1.1.1.8.5.1 |
swEventIndexThis object identifies the event entry.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.8.5.1.1 |
swEventTimeInfoThis object identifies the date and time when this event occurred, in textual format.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.8.5.1.2 |
swEventLevelThis object identifies the severity level of this event entry.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.8.5.1.3 |
swEventRepeatCountThis object identifies how many times this particular event has occurred.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.8.5.1.4 |
swEventDescrThis object identifies the textual description of the event.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1588.2.1.1.1.8.5.1.5 |
swFwSystemThe OID sub-tree for swFwSystem group. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1.10 |
swFwFabricWatchLicensetells if licensed or not.ro SwFwLicense .1.3.6.1.4.1.1588.2.1.1.1.10.1 |
swFwClassAreaTableThe table of classes and areas. SEQUENCE OF SwFwClassAreaEntry .1.3.6.1.4.1.1588.2.1.1.1.10.2 |
swFwClassAreaEntryAn entry of the classes and areas. SwFwClassAreaEntry .1.3.6.1.4.1.1588.2.1.1.1.10.2.1 |
swFwClassAreaIndexThis object identifies the class type.ro SwFwClassesAreas .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.1 |
swFwWriteThValsThis object is set to apply the value changes.rw SwFwWriteVals .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.2 |
swFwDefaultUnitA Default unit string name for a threshold area.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.3 |
swFwDefaultTimebaseA Default timebase for the current threshold counter.ro SwFwTimebase .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.4 |
swFwDefaultLowA Default low threshold value.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.5 |
swFwDefaultHighA Default high threshold value.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.6 |
swFwDefaultBufSizeA Default buffer size value.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.7 |
swFwCustUnitA custom unit string name for a threshold area.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.8 |
swFwCustTimebaseA custom timebase for the current threshold counter.rw SwFwTimebase .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.9 |
swFwCustLowA custom low threshold value.rw Integer32 .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.10 |
swFwCustHighA custom high threshold value.rw Integer32 .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.11 |
swFwCustBufSizeA custom buffer size value.rw Integer32 .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.12 |
swFwThLevelA level where all the threshold values are set at.rw SwFwLevels .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.13 |
swFwWriteActValsThis object is set to apply act value changes.rw SwFwWriteVals .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.14 |
swFwDefaultChangedActsDefault action matrix for changed event.ro SwFwActs .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.15 |
swFwDefaultExceededActsDefault action matrix for exceeded event.ro SwFwActs .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.16 |
swFwDefaultBelowActsDefault action matrix for below event.ro SwFwActs .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.17 |
swFwDefaultAboveActsDefault action matrix for above event.ro SwFwActs .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.18 |
swFwDefaultInBetweenActsDefault action matrix for in-between event.ro SwFwActs .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.19 |
swFwCustChangedActscustom action matrix for changed event.rw SwFwActs .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.20 |
swFwCustExceededActscustom action matrix for exceeded event.rw SwFwActs .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.21 |
swFwCustBelowActscustom action matrix for below event.rw SwFwActs .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.22 |
swFwCustAboveActscustom action matrix for above event.rw SwFwActs .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.23 |
swFwCustInBetweenActscustom action matrix for in-between event.rw SwFwActs .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.24 |
swFwValidActsmatrix of valid acts for an class/area.ro SwFwActs .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.25 |
swFwActLevelA level where all the actions are set at.rw SwFwLevels .1.3.6.1.4.1.1588.2.1.1.1.10.2.1.26 |
swFwThresholdTableThe table of individual thresholds. SEQUENCE OF SwFwThresholdEntry .1.3.6.1.4.1.1588.2.1.1.1.10.3 |
swFwThresholdEntryAn entry of an individual threshold. SwFwThresholdEntry .1.3.6.1.4.1.1588.2.1.1.1.10.3.1 |
swFwThresholdIndexThis object identifies the element index of an threshold.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.10.3.1.1 |
swFwStatusThis object identifies if an threshold is enabled or disabled.rw SwFwStatus .1.3.6.1.4.1.1588.2.1.1.1.10.3.1.2 |
swFwNameThis object is a name of the threshold.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.10.3.1.3 |
swFwLabelThis object is a label of the threshold.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.10.3.1.4 |
swFwCurValThis object is a current counter of the threshold.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.10.3.1.5 |
swFwLastEventThis object is a last event type of the threshold.ro SwFwEvent .1.3.6.1.4.1.1588.2.1.1.1.10.3.1.6 |
swFwLastEventValThis object is a last event value of the threshold.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.10.3.1.7 |
swFwLastEventTimeThis object is a last event time of the threshold.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.10.3.1.8 |
swFwLastStateThis object is a last event state of the threshold.ro SwFwState .1.3.6.1.4.1.1588.2.1.1.1.10.3.1.9 |
swFwBehaviorTypeA behavior of which the thresholds generate event.rw SwFwBehavior .1.3.6.1.4.1.1588.2.1.1.1.10.3.1.10 |
swFwBehaviorIntA integer of which the thresholds generate continuous event.rw Integer32 .1.3.6.1.4.1.1588.2.1.1.1.10.3.1.11 |
swFwLastSeverityLevelThis object is a last event severity level of the threshold.ro SwSevType .1.3.6.1.4.1.1588.2.1.1.1.10.3.1.12 |
swEndDeviceThe OID sub-tree for swEndDevice group. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1.21 |
swEndDeviceRlsTableThe table of individual end devices' rls. SEQUENCE OF SwEndDeviceRlsEntry .1.3.6.1.4.1.1588.2.1.1.1.21.1 |
swEndDeviceRlsEntryAn entry of an individual end devices' rls. SwEndDeviceRlsEntry .1.3.6.1.4.1.1588.2.1.1.1.21.1.1 |
swEndDevicePortThis object identifies the port of the end device. Integer32 .1.3.6.1.4.1.1588.2.1.1.1.21.1.1.1 |
swEndDeviceAlpaThis object identifies the alpa of the end device. Integer32 .1.3.6.1.4.1.1588.2.1.1.1.21.1.1.2 |
swEndDevicePortIDThe object identifies the Fibre Channel port address ID of the entry.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.21.1.1.3 |
swEndDeviceLinkFailureLink failure count for the end device.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.21.1.1.4 |
swEndDeviceSyncLossSync loss count for the end device.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.21.1.1.5 |
swEndDeviceSigLossSig loss count for the end device.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.21.1.1.6 |
swEndDeviceProtoErrProtocol err count for the end device.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.21.1.1.7 |
swEndDeviceInvalidWordInvalid word count for the end device.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.21.1.1.8 |
swEndDeviceInvalidCRCInvalid CRC count for the end device.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.21.1.1.9 |
swGroupThe OID sub-tree for swGroup group. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1.22 |
swGroupTableThe table of groups. This may not be available on all versions of Fabric OS. SEQUENCE OF SwGroupEntry .1.3.6.1.4.1.1588.2.1.1.1.22.1 |
swGroupEntryAn entry of table of groups. SwGroupEntry .1.3.6.1.4.1.1588.2.1.1.1.22.1.1 |
swGroupIndexThis object is the group index starting from 1.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.22.1.1.1 |
swGroupNameThis object identifies the name of the group.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.22.1.1.2 |
swGroupTypeThis object identifies the type of the group.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.22.1.1.3 |
swGroupMemTableThe table of members of all groups. This may not be available on all versions of Fabric OS. SEQUENCE OF SwGroupMemEntry .1.3.6.1.4.1.1588.2.1.1.1.22.2 |
swGroupMemEntryAn entry for a member of a group. SwGroupMemEntry .1.3.6.1.4.1.1588.2.1.1.1.22.2.1 |
swGroupIdThis object identifies the Group Id of the member switch.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.22.2.1.1 |
swGroupMemWwnThis object identifies the WWN of the member switch.ro FcWwn (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.22.2.1.2 |
swGroupMemPosThis object identifies position of the member switch in the group. This is based on the order that the switches were added in the group.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.22.2.1.3 |
swBlmPerfMntThe OID sub-tree for swBlmPerfMnt (Bloom Performance Monitor) group. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1.23 |
swBlmPerfALPAMntTableALPA monitoring counter Table. SEQUENCE OF SwBlmPerfALPAMntEntry .1.3.6.1.4.1.1588.2.1.1.1.23.1 |
swBlmPerfALPAMntEntryALPA monitoring counter for given ALPA. SwBlmPerfALPAMntEntry .1.3.6.1.4.1.1588.2.1.1.1.23.1.1 |
swBlmPerfAlpaPortThis Object identifies the port index of the switch.ro SwPortIndex (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.23.1.1.1 |
swBlmPerfAlpaIndxThis Object identifies the ALPA index. There can be 126 ALPA valuesro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.23.1.1.2 |
swBlmPerfAlpaThis Object identifies the ALPA values. These values range between x'01' and x'EF'(1 to 239). ALPA value x'00' is reserved for FL_Port If Alpa device is invalid, then it will have -1 value.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.23.1.1.3 |
swBlmPerfAlpaCRCCntGet CRC count for given ALPA and port. This monitoring provides information on the number of CRC errors occurred on the frames destined to each possible ALPA attached to a specific port.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.23.1.1.4 |
swBlmPerfEEMntTableEnd-to-End monitoring counter Table SEQUENCE OF SwBlmPerfEEMntEntry .1.3.6.1.4.1.1588.2.1.1.1.23.2 |
swBlmPerfEEMntEntryEnd-to-End monitoring counter for given port. SwBlmPerfEEMntEntry .1.3.6.1.4.1.1588.2.1.1.1.23.2.1 |
swBlmPerfEEPortThis object identifies the port number of the switch.ro SwPortIndex (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.23.2.1.1 |
swBlmPerfEERefKeyThis object identifies the reference number of the counter. This reference is number assigned when a filter is created. In SNMP Index start one instead of 0, add one to actual ref keyro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.23.2.1.2 |
swBlmPerfEECRCGet End to End CRC error for the frames that matched the SID-DID pair.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.23.2.1.3 |
swBlmPerfEEFCWRxGet End to End count of Fibre Channel words (FCW), received by the port, that matched the SID-DID pair.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.23.2.1.4 |
swBlmPerfEEFCWTxGet End to End count of Fibre Channel words (FCW), transmitted by the port, that matched the SID-DID pair.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.23.2.1.5 |
swBlmPerfEESidGets SID info by reference number. SID (Source Identifier) is a 3-byte field in the frame header used to indicate the address identifier of the N-Port from which the frame was sent.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.23.2.1.6 |
swBlmPerfEEDidGets DID info by reference number. DID (Destination Identifier) is a 3-byte field in the frame header used to indicate the address identifier of the N-Port to which the frame was sent.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.23.2.1.7 |
swBlmPerfFltMntTableFilter based monitoring counter. SEQUENCE OF SwBlmPerfFltMntEntry .1.3.6.1.4.1.1588.2.1.1.1.23.3 |
swBlmPerfFltMntEntryFilter base monitoring counter for given port. SwBlmPerfFltMntEntry .1.3.6.1.4.1.1588.2.1.1.1.23.3.1 |
swBlmPerfFltPortThis object identifies the port number of the switch.ro SwPortIndex (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.23.3.1.1 |
swBlmPerfFltRefkeyThis object identifies the reference number of the filter. This reference number is assigned when a filter is created. In SNMP Index start one instead of 0, add one to actual ref keyro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.23.3.1.2 |
swBlmPerfFltCntGet statistics of filter based monitor. Filter based monitoring provides information about a filter hit count such as 1. Read command 2. SCSI or IP traffic 3. SCSI Read/Writero OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.23.3.1.3 |
swBlmPerfFltAliasAlias name for the filter.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.23.3.1.4 |
swTrunkThe OID sub-tree for swTrunk group. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1.24 |
swSwitchTrunkableThe trunking status of the switch - whether the switch supports the trunking feature or not. The values are yes(8) - the trunking feature is supported no(0). - the trunking feature is not supported.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.24.1 |
swTrunkTableTable to display trunking information for the switch. SEQUENCE OF SwTrunkEntry .1.3.6.1.4.1.1588.2.1.1.1.24.2 |
swTrunkEntryEntry for the trunking table. SwTrunkEntry .1.3.6.1.4.1.1588.2.1.1.1.24.2.1 |
swTrunkPortIndexThis object identifies the switch port index. Note that the value of a port index is 1 higher than the port number labeled on the front panel. e.g. port index 1 correspond to port number 0.ro SwPortIndex (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.24.2.1.1 |
swTrunkGroupNumberThis object is a logical entity which specifies the Group Number to which the port belongs to. If this value is Zero it means the port is not Trunked.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.24.2.1.2 |
swTrunkMasterPort number that is the trunk master of the group. The trunk master implicitly defines the group. All ports with the same master are considered to be part of the same group.ro SwTrunkMaster (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.24.2.1.3 |
swPortTrunkedThe current state of trunking for a member port. Values are enabled(1) or disabled(0).ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.24.2.1.4 |
swTrunkGrpTableTable to display trunking Performance information for the switch. SEQUENCE OF SwTrunkGrpEntry .1.3.6.1.4.1.1588.2.1.1.1.24.3 |
swTrunkGrpEntryEntry for the trunking Group table. SwTrunkGrpEntry .1.3.6.1.4.1.1588.2.1.1.1.24.3.1 |
swTrunkGrpNumberThis object is a logical entity which specifies the Group Number to which port belongs to.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.24.3.1.1 |
swTrunkGrpMasterThis object gives the master port id for the TrunkGroup.ro SwTrunkMaster (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.24.3.1.2 |
swTrunkGrpTxGives the aggregate value of the transmitted words from this TrunkGroup.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.24.3.1.3 |
swTrunkGrpRxGives the aggregate value of the received words by this TrunkGroup.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.24.3.1.4 |
sw28kThe OID for Brocade's Silkworm 2800 model Fibre Channel Switch. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.2 |
sw21kN24kThe OID for Brocade's Silkworm 2100 and 2400 series model Fibre Channel Switch. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.3 |
sw20x0The OID for Brocade's Silkworm 20x0 series model Fibre Channel Switch. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.4 |
swMibModuleThe MIB module is for Brocade's Fibre Channel Switch. Copyright (c) 1996-2003 Brocade Communications Systems, Inc. All rights reserved. MODULE-IDENTITY .1.3.6.1.4.1.1588.3.1.3 |