BROCADE-SYSTEM-MIB
AI MIB Summary
The BROCADE-SYSTEM-MIB provides standard SNMP access to Brocade Fibre Channel and Ethernet switch system-level attributes, including device identity, hardware status, environmental sensors, and operational counters. It enables centralized monitoring of critical infrastructure health metrics such as temperature, fan status, power supply states, and system uptime across the Brocade SAN and LAN fabric.
The MIB module is for system information. Copyright (c) 1996-2003 Brocade Communications Systems, Inc. All rights reserved.
Main OID:
swSystem.1.3.6.1.4.1.1588.2.1.1.1.1
81
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
81 total| Object Name |
|---|
swTrapsV2The Traps for Brocade's Switch. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1.0 |
swFCPortScnThis trap is sent whenever an FC port operational status or its type changed. The events that trigger this trap are port goes to online/offline, port type changed to E-port/F-port/FL-port. swFCPortName and swSsn are optional varbind in the trap PDU.swSsn is optional varbind sent when swExtTrap is also enabled.swVfId is optional if VF is enabled. NOTIFICATION-TYPE .1.3.6.1.4.1.1588.2.1.1.1.0.3 |
swEventTrapThis trap is generated when an event whose level at or below swEventTrapLevel occurs. NOTIFICATION-TYPE .1.3.6.1.4.1.1588.2.1.1.1.0.4 |
swStateChangeTrapThis trap is sent whenever switch state changes to online/offline NOTIFICATION-TYPE .1.3.6.1.4.1.1588.2.1.1.1.0.12 |
swSystemThe MIB module is for system information. Copyright (c) 1996-2003 Brocade Communications Systems, Inc. All rights reserved. MODULE-IDENTITY .1.3.6.1.4.1.1588.2.1.1.1.1 |
swCurrentDateThe current date information in displayable textual format.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.1 |
swBootDateThe date and time when the system last booted, in displayable textual format.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.2 |
swFWLastUpdatedThe information indicates the date when the firmware was last updated, in displayable textual format.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.3 |
swFlashLastUpdatedThe information indicates the date when the FLASH was last updated, in displayable textual format.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.4 |
swBootPromLastUpdatedThe information indicates the date when the boot PROM was last updated, in displayable textual format.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.5 |
swFirmwareVersionThe current version of the firwmare.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.6 |
swOperStatusThe current operational status of the switch. The states are as follow: o online(1) means the switch is accessible by an external port; o offline(2) means the switch is not accessible; o testing(3) means the switch is in a built-in test mode and is not accessible by an external port; o faulty(4) means the switch is not operational.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.7 |
swSsnThe soft serial number of the switch.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.10 |
swFlashDLOperStatusThe operational status of the FLASH. The operational states are as follow: o swCurrent(1) indicates that the FLASH contains the current firmware image or config file; o swFwUpgraded(2) state indicates that it contains the image upgraded from the swFlashDLHost.0.; o swCfUploaded(3) state indicates that the switch configuration file has been uploaded to the host; and o swCfDownloaded(4) state indicates that the switch configuration file has been downloaded from the host. o swFwCorrupted (5) state indicates that the firmware in the FLASH of the switch is corrupted.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.11 |
swFlashDLAdmStatusThe state of the FLASH. o swCurrent(1) indicates that the FLASH contains the current firmware image or config file; o swFwUpgrade(2) means that the firmware in the FLASH is to be upgraded from the host specified; o swCfUpload(3) means that the switch config file is to be uploaded to the host specified; or o swCfDownload(4) means that the switch config file is to be downloaded from the host specified. o swFwCorrupted(5) state indicates that the firmware in the FLASH is corrupted. This value is for informational purpose only. However, set of swFlashDLAdmStatus to this value is not allowed. The host is specified in swFlashDLHost.0. In addition, user name is specified in swFlashDLUser.0, and the file name specified in swFlashDLFile.0. Reference the user manual on the following commands, o firmwareDownload, o configUpload, and o configDownload.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.12 |
swBeaconOperStatusThe current operational status of the switch beacon. When the beacon is on, the LEDs on the front panel of the switch run alternately from left to right and right to left. The color is yellow. When the beacon is off, each LED will be in their its regular status indicating color and state.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.18 |
swBeaconAdmStatusThe desired status of the switch beacon. When the beacon is set to on, the LEDs on the front panel of the switch run alternately from left to right and right to left. The color is yellow. When the beacon is set to off, each LED will be in its regular status indicating color and state.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.19 |
swDiagResultThe result of the power-on startup (POST) diagnostics.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.20 |
swNumSensorsThe number of sensors inside the switch.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.1.21 |
swSensorTableThe table of sensor entries. SEQUENCE OF SwSensorEntry .1.3.6.1.4.1.1588.2.1.1.1.1.22 |
swSensorEntryAn entry of the sensor information. SwSensorEntry .1.3.6.1.4.1.1588.2.1.1.1.1.22.1 |
swSensorIndexThis object identifies the sensor.ro SwSensorIndex (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.1.22.1.1 |
swSensorTypeThis object identifies the sensor type.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.22.1.2 |
swSensorStatusThe current status of the sensor.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.22.1.3 |
swSensorValueThe current value (reading) of the sensor. The value, -2147483648, represents an unknown quantity. It also means that the sensor does not have the capability to measure the actual value. In V2.0, the temperature sensor value will be in Celsius; the fan value will be in RPM (revolution per minute); and the power supply sensor reading will be unknown.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.1.22.1.4 |
swSensorInfoAdditional displayable information on the sensor. In V2.x, it contains the sensor type and number in textual format. For example, 'Temp 3', 'Fan 6'.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.1.22.1.5 |
swIDThe number of the logical switch (0/1).ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.1.24 |
swEtherIPAddressThe IP Address of the Ethernet interface of this logical switch.ro IpAddress .1.3.6.1.4.1.1588.2.1.1.1.1.25 |
swEtherIPMaskThe IP Mask of the Ethernet interface of this logical switch.ro IpAddress .1.3.6.1.4.1.1588.2.1.1.1.1.26 |
swIPv6AddressIPV6 address. DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1588.2.1.1.1.1.29 |
swIPv6StatusThe current status of ipv6 address. Enumeration .1.3.6.1.4.1.1588.2.1.1.1.1.30 |
swFabricThe OID sub-tree for swFabric group. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1.2 |
swVfIdThe Virtual fabric id.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.2.15 |
swFCportThe OID sub-tree for swFCport group. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1.6 |
swFCPortTableA table that contains, one entry for each switch port, configuration and service parameters of the port. SEQUENCE OF SwFCPortEntry .1.3.6.1.4.1.1588.2.1.1.1.6.2 |
swFCPortEntryAn entry containing the configuration and service parameters of the switch port. SwFCPortEntry .1.3.6.1.4.1.1588.2.1.1.1.6.2.1 |
swFCPortIndexThis object identifies the switch port index. Note that the value of a port index is 1 higher than the port number labeled on the front panel. E.g. port index 1 correspond to port number 0.ro SwPortIndex (Brocade-TC) .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.1 |
swFCPortTypeThis object identifies the type of switch port. It may be of type stitch(1), flannel(2), loom(3) , bloom(4),rdbloom(5) or wormhole(6).ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.2 |
swFCPortPhyStateThis object identifies the physical state of the port: noCard(1) no card present in this switch slot; noTransceiver(2) no Transceiver module in this port. noGbic(2) was used previously. Transceiver is the generic name for GBIC, SFP etc.; laserFault(3) the module is signaling a laser fault (defective Transceiver); noLight(4) the module is not receiving light; noSync(5) the module is receiving light but is out of sync; inSync(6) the module is receiving light and is in sync; portFault(7) the port is marked faulty (defective Transceiver, cable or device); diagFault(8) the port failed diagnostics (defective G_Port or FL_Port card or motherboard); lockRef(9) the port is locking to the reference signal. validating(10) Validation is in progress invalidModule(11) Invalid SFP unknown(255) unknown.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.3 |
swFCPortOpStatusThis object identifies the operational status of the port. The online(1) state indicates that user frames can be passed. The unknown(0) state indicates that likely the port module is physically absent (see swFCPortPhyState).ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.4 |
swFCPortAdmStatusThe desired state of the port. A management station may place the port in a desired state by setting this object accordingly. The testing(3) state indicates that no user frames can be passed. As the result of either explicit management action or per configuration information accessible by the switch, swFCPortAdmStatus is then changed to either the online(1) or testing(3) states, or remains in the offline(2) state.rw Enumeration .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.5 |
swFCPortLinkStateThis object indicates the link state of the port. The value may be: enabled(1) - port is allowed to participate in the FC-PH protocol with its attached port (or ports if it is in a FC-AL loop); disabled(2) - the port is not allowed to participate in the FC-PH protocol with its attached port(s); loopback(3) - the port may transmit frames through an internal path to verify the health of the transmitter and receiver path. Note that when the port's link state changes, its operational status (swFCPortOpStatus) will be affected.rw Enumeration .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.6 |
swFCPortTxTypeThis object indicates the media transmitter type of the port. The value may be: unknown(1) cannot determined to the port driver lw(2) long wave laser sw(3) short wave laser ld(4) long wave LED cu(5) copper (electrical).ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.7 |
swFCPortTxWordsThis object counts the number of Fibre Channel words that the port has transmitted.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.11 |
swFCPortRxWordsThis object counts the number of Fibre Channel words that the port has received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.12 |
swFCPortTxFramesThis object counts the number of (Fibre Channel) frames that the port has transmitted.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.13 |
swFCPortRxFramesThis object counts the number of (Fibre Channel) frames that the port has received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.14 |
swFCPortRxC2FramesThis object counts the number of Class 2 frames that the port has received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.15 |
swFCPortRxC3FramesThis object counts the number of Class 3 frames that the port has received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.16 |
swFCPortRxLCsThis object counts the number of Link Control frames that the port has received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.17 |
swFCPortRxMcastsThis object counts the number of Multicast frames that the port has received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.18 |
swFCPortTooManyRdysThis object counts the number of times when RDYs exceeds the frames received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.19 |
swFCPortNoTxCreditsThis object counts the number of times when the transmit credit has reached zero.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.20 |
swFCPortRxEncInFrsThis object counts the number of encoding error or disparity error inside frames received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.21 |
swFCPortRxCrcsThis object counts the number of CRC errors detected for frames received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.22 |
swFCPortRxTruncsThis object counts the number of truncated frames that the port has received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.23 |
swFCPortRxTooLongsThis object counts the number of received frames that are too long.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.24 |
swFCPortRxBadEofsThis object counts the number of received frames that have bad EOF delimiter.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.25 |
swFCPortRxEncOutFrsThis object counts the number of encoding error or disparity error outside frames received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.26 |
swFCPortRxBadOsThis object counts the number of invalid Ordered Sets received.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.27 |
swFCPortC3DiscardsThis object counts the number of Class 3 frames that the port has discarded.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.28 |
swFCPortMcastTimedOutsThis object counts the number of Multicast frames that has been timed out.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.29 |
swFCPortTxMcastsThis object counts the number of Multicast frames that has been transmitted.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.30 |
swFCPortLipInsThis object counts the number of Loop Initializations that has been initiated by loop devices attached.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.31 |
swFCPortLipOutsThis object counts the number of Loop Initializations that has been initiated by the port.ro Counter32 .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.32 |
swFCPortLipLastAlpaThis object indicates the Physical Address (AL_PA) of the loop device that initiated the last Loop Initialization.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.33 |
swFCPortWwnThe World_wide_Name of the Fibre Channel port. The contents of an instance are in the IEEE extended format as specified in FC-PH; the 12-bit port identifier represents the port number within the switch.ro OCTET STRING .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.34 |
swFCPortSpeedThe desired baud rate for the port. It can have the values of 1GB (1), 2GB (2), Auto-Negotiate (3), 4GB (4), 8GB (5), or 10GB (6). Some of the above values may not be supported by all type of switches.rw Enumeration .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.35 |
swFCPortNameA string indicates the name of the addressed port. The names should be persistent across switch reboots. Port names do not have to be unique within a switch or within a fabric.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.36 |
swFCPortSpecifierThis string indicates the physical port number of the addressed port. The format of the string is: <slot>/port, where 'slot' being present only for bladed systems.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.37 |
swFCPortFlagA bit map of port status flags which includes the information of port type. Currently this will indicate if the port is virtual or physical.ro FcPortFlag .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.38 |
swFCPortBrcdTypeThe Brocade port type.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.6.2.1.39 |
swEventThe OID sub-tree for swEvent group. OBJECT IDENTIFIER .1.3.6.1.4.1.1588.2.1.1.1.8 |
swEventTableThe table of event entries. SEQUENCE OF SwEventEntry .1.3.6.1.4.1.1588.2.1.1.1.8.5 |
swEventEntryAn entry of the event table. SwEventEntry .1.3.6.1.4.1.1588.2.1.1.1.8.5.1 |
swEventIndexThis object identifies the event entry.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.8.5.1.1 |
swEventTimeInfoThis object identifies the date and time when this event occurred, in textual format.ro DisplayString .1.3.6.1.4.1.1588.2.1.1.1.8.5.1.2 |
swEventLevelThis object identifies the severity level of this event entry.ro Enumeration .1.3.6.1.4.1.1588.2.1.1.1.8.5.1.3 |
swEventRepeatCountThis object identifies how many times this particular event has occurred.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.8.5.1.4 |
swEventDescrThis object identifies the textual description of the event.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1588.2.1.1.1.8.5.1.5 |
swEventVfIdThis object identifies the Virtual fabric id.ro Integer32 .1.3.6.1.4.1.1588.2.1.1.1.8.5.1.6 |