SL-XPDR-MIB
This MIB module describes the optical connections.
Main OID:
slXpdr.1.3.6.1.4.1.4515.1.8
30
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
30 total| Object Name |
|---|
slXpdrThis MIB module describes the optical connections. MODULE-IDENTITY .1.3.6.1.4.1.4515.1.8 |
slXpdrConn OBJECT IDENTIFIER .1.3.6.1.4.1.4515.1.8.1 |
xpdrConnConfigTableThe connection table contains for each
transponding connection a single bi-directional entry.
The index to the table is the ifIndex of both XPDR interfaces.
The ifType valued used for the index is: 196. SEQUENCE OF XpdrConnConfigEntry .1.3.6.1.4.1.4515.1.8.1.1 |
xpdrConnConfigEntryAn entry in the transponding connection table. XpdrConnConfigEntry .1.3.6.1.4.1.4515.1.8.1.1.1 |
xpdrConnConfigIf1The first XPDR interface.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4515.1.8.1.1.1.1 |
xpdrConnConfigIf2The second XPDR interface.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4515.1.8.1.1.1.2 |
xpdrConnConfigRateControlAdminThis variable ask the rate of the traffic used
by this interface. Frequency is in Kbp/s.
The value 0-30 is used for rate control Bypass.rw INTEGER .1.3.6.1.4.1.4515.1.8.1.1.1.3 |
xpdrConnConfigRateControlOperThis variable tells the rate of the traffic used
by this interface. Frequency is in Kbp/s.
The value 0 returned for rate control Bypass.ro INTEGER .1.3.6.1.4.1.4515.1.8.1.1.1.4 |
xpdrConnConfigLosPropagationThis object is used to detrmine if the LOS propagation should be active.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4515.1.8.1.1.1.5 |
xpdrServiceTypeThe service type of the transponder.rw XpdrServiceType .1.3.6.1.4.1.4515.1.8.1.1.1.6 |
xpdrConnAddMaskThis object is a bit mask relevant only for Muxponder entry.
It contains a bit for each Muxponder service.
To add a service the management should set the corresponding bit to 1.
To remove a service the bit should be set to 0.
For ODU allocation, the value of xpdrConnAddMask should be set to reflect the odus/time-slots
provisioned for the service according to the following rules:
a. For ODU1 the first byte is 0; for ODU0 the first byte is 1.
b. The second byte. Is equal to:
i. The 4 bits of the first nibble correspond to Uplink 1 allocated odus counted from right to left
ii. The 4 bits of the second nibble correspond to Uplink 2 allocated odus counted from right to left
c. The Third and Forth bytes keep bit-mask of the allocated time-slots within the odu.rw INTEGER .1.3.6.1.4.1.4515.1.8.1.1.1.7 |
xpdrMuxInbandAdminThis object is relevant only for muxponder.
up value means that the muxponder inband management is enabled.rw Enumeration .1.3.6.1.4.1.4515.1.8.1.1.1.8 |
xpdrMuxInbandOperThe operational state of the inband interface.ro Enumeration .1.3.6.1.4.1.4515.1.8.1.1.1.9 |
xpdrDirectionThis object is used for unidirectional services.
The upper port is the uplink as with the aps configuration.
The transponder on one side should be configured as TX and the peer as RX.rw Enumeration .1.3.6.1.4.1.4515.1.8.1.1.1.10 |
xpdrConnConfigCpriRateControlThis object is used to detrmine if the CPRI rate control should be active.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4515.1.8.1.1.1.11 |
xpdrFaultPropagationDelayThis object is used to determine the fault propagation delay.
The value 0 mean no delay, the value 1 means 100ms delay, the value 2 means 200ms delay etc.
0 is the default value.rw INTEGER .1.3.6.1.4.1.4515.1.8.1.1.1.12 |
xpdrFecModeThis object is used to determine the IEEE FEC mode for 10G and 16G services:
0 - No FEC (default)
1 - FEC Monitoring
2 - FEC Generation
3 - FEC Regenerationrw INTEGER .1.3.6.1.4.1.4515.1.8.1.1.1.13 |
oduXcConnConfigTableDescription:
1. The port numbers are:
0 unassigned
1..10 ODUs of Uplink 1
11..20 ODUs of Uplink 2 (not available without 20G or 1+1 license)
2. All connections are unidirectional
3. P1 is the Source port and P2 is the Sync port
4. Port 0 is used as P2 when P1 is dropped
5. Port 0 is used as P1 when P2 is added
6. In the case of APS the two mate ODUs will apear with oduXcConnConfigProtected=TRUE
7. The allocation of ODUs per service port is described in xpdrConnAddMask above SEQUENCE OF OduXcConnConfigEntry .1.3.6.1.4.1.4515.1.8.1.2 |
oduXcConnConfigEntryAn entry in the ODU connection table.
An entry describes uni-directional connection of traffic from P1 (Source port) to port P2 (Sync port). OduXcConnConfigEntry .1.3.6.1.4.1.4515.1.8.1.2.1 |
oduXcConnConfigP1The Source port.rw INTEGER .1.3.6.1.4.1.4515.1.8.1.2.1.1 |
oduXcConnConfigP2The Sync port.rw INTEGER .1.3.6.1.4.1.4515.1.8.1.2.1.2 |
oduXcConnConfigProtectedIndication for entry with Protection Matesrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4515.1.8.1.2.1.3 |
oduXcConnConfigRowStatusThe Status of this connection entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4515.1.8.1.2.1.4 |
xpdrOduMappingStatusA bit mask that specifies how the ODUs are configured.
The first nible describes Uplink 1 and the second nibble describes Uplink 2.
Examples:
If bit 1 equals 1 it means that the first ODU1 of Uplink 1 is devided into two ODU0.
If bit 8 equals 1 it means that the forth ODU1 of Uplink 2 is devided into two ODU0.
The default value is 0, means that all ODUs are ODU1.ro INTEGER .1.3.6.1.4.1.4515.1.8.1.3 |
xpdrOduMappingMaskedAdminThe first byte is the new mapping to set.
The second byte is the mask for the setting.
For example to split the second ODU1 of Uplink 1 into two ODU0
First byte should be - 01000000
Second byte should be - 01000000
To change the reunite the third ODU1 of uplink 2
First byte should be - 00000000
Second byte should be - 00000010rw INTEGER .1.3.6.1.4.1.4515.1.8.1.4 |
slXpdrLastChange OBJECT IDENTIFIER .1.3.6.1.4.1.4515.1.8.6 |
slXpdrTraps OBJECT IDENTIFIER .1.3.6.1.4.1.4515.1.8.7 |
slXpdrTraps0 OBJECT IDENTIFIER .1.3.6.1.4.1.4515.1.8.7.0 |
xpdrConnConfigTableChange0A xpdrConnConfigTableChange trap is sent when the
content of the xpdrConnConfigTable is changed.
It is defined to support browsers that don't recognize RFC 2576. NOTIFICATION-TYPE .1.3.6.1.4.1.4515.1.8.7.0.1 |
xpdrConnConfigTableChangeA xpdrConnConfigTableChange trap is sent when the
content of the xpdrConnConfigTable is changed. NOTIFICATION-TYPE .1.3.6.1.4.1.4515.1.8.7.1 |