SL-MAIN-MIB
AI MIB Summary
The SL-MAIN-MIB module provides SNMP access to monitor and manage the operational status, hardware health, and system resources of the main board on Schneider Electric (formerly Telemecanique) industrial automation controllers. It exposes critical metrics including CPU utilization, memory usage, temperature sensors, and power supply states to facilitate real-time fault detection and preventive maintenance.
This MIB module describes the Main Board
Main OID:
slMain.1.3.6.1.4.1.4515.1.3
120
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
120 total| Object Name |
|---|
slMainThis MIB module describes the Main Board MODULE-IDENTITY .1.3.6.1.4.1.4515.1.3 |
slmSys OBJECT IDENTIFIER .1.3.6.1.4.1.4515.1.3.1 |
slmSysGatewayAddrGateway node IP Address.rw IpAddress .1.3.6.1.4.1.4515.1.3.1.1 |
slmSysSubnetMaskSubnetwork Mask IP Address.rw IpAddress .1.3.6.1.4.1.4515.1.3.1.2 |
slmSysIpAddrNode IP Address.rw IpAddress .1.3.6.1.4.1.4515.1.3.1.3 |
slmSysAlmActAlarm Activation Time specified in Half-Seconds units.
Alarm will be considered active only if it
has been stable for that time.rw INTEGER .1.3.6.1.4.1.4515.1.3.1.4 |
slmSysAlmDeactAlarm Clearance Time specified in Half-Seconds units.
Alarm will be considered clear only if it
has been stable for that time.rw INTEGER .1.3.6.1.4.1.4515.1.3.1.5 |
slmSysAdminStatusInstruct the system to perform the boot
according to the specified type.rw Enumeration .1.3.6.1.4.1.4515.1.3.1.6 |
slmSysOperStatusThe operational system state.ro Enumeration .1.3.6.1.4.1.4515.1.3.1.7 |
slmBoxSizeThe box size as was configured in the SEEP.ro Enumeration .1.3.6.1.4.1.4515.1.3.1.8 |
slmSysCalendarTimeThe system calendar time.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.4515.1.3.1.9 |
slmSysPmStartOfDayThe time of day that marks the beginning of each 1-day interval
used in the performance monitoring parameters for all interfaces
in the NE. This time is on an hour boundary.rw INTEGER .1.3.6.1.4.1.4515.1.3.1.10 |
slmSysActiveSwVersionDetermines the active software version. This is the version that will
be loaded by rebooted cards. It is not legal to set this object
to the id of an illegal system software version.
swRevFtpStart(3) - is set by the NMS to signal the FTP start.
swRevFtpEnd(4) - is set by the NMS to signal the FTP completion.
swRevAHot(5) - means to change the active software version to A,
and to preform hot restart to all cards.
swRevBHot(6) - means to change the active software version to B,
and to preform hot restart to all cards.
Reading the object returns the current active software version.rw Enumeration .1.3.6.1.4.1.4515.1.3.1.11 |
slmSwRevTableThis table keeps the information about the system
software revisions. SEQUENCE OF SlmSwRevEntry .1.3.6.1.4.1.4515.1.3.1.12 |
slmSwRevEntryAn entry exist per system revsion type (A or B). SlmSwRevEntry .1.3.6.1.4.1.4515.1.3.1.12.1 |
slmSwRevDirectoryThe directory name A or B of this system software
revision.ro Enumeration .1.3.6.1.4.1.4515.1.3.1.12.1.1 |
slmSwRevStatusThe status of the system software directory content.
The value valid(1) means that the data of this entry is
valid and that the software is loaded correctly and is
currently used.
The value copyingToStandby(3) means that the SW is currently
being copied to the Standby Switch. During this period
the NMS is not allowed to upgrade the SW version. This value
is applicable only to the Standby software version.
The value invalid(2) means otherwise. This value is applicable
only to the Standby software version.ro Enumeration .1.3.6.1.4.1.4515.1.3.1.12.1.2 |
slmSwRevNameThe identification string of the system software revision.
This value is taken from the content of the system software
configuration data that is downloded with the rest of the
software files.ro SoftwareRevision .1.3.6.1.4.1.4515.1.3.1.12.1.3 |
slmSwRevDateThe release date of the system software revision.
This value is taken from the content of the system software
configuration data that is downloded with the rest of the
software files.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.4515.1.3.1.12.1.4 |
slmConfigSysUptimeThe number of timer ticks at the last configuration command.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.4515.1.3.1.13 |
slmConfigSysSignalTypeThis variable identifies whether a SONET
or a SDH signal is used across this node.
This value is configured by the NMS.rw Enumeration .1.3.6.1.4.1.4515.1.3.1.14 |
slmRebootDelayThe number of seconds to wait before reboot.
When this number equal to 0 the reboot should occur immediately.
After the reboot command is initiated, the value of this object
decrements accordingly.
Initially, the object value is 0.
It is also possible to change this value after starting the reboot
process.
Getting the value 0 means that there is no
pending reboot process in the background.rw INTEGER .1.3.6.1.4.1.4515.1.3.1.16 |
slmVcatDelayThe value of the VCAT delay as was read from the SEEP.ro INTEGER .1.3.6.1.4.1.4515.1.3.1.17 |
slmTidThe SL TL1 name.rw DisplayString .1.3.6.1.4.1.4515.1.3.1.18 |
slmPsuNumberLet the NMS to configure the number of PSU in the system.
If this number mismatch the reality, a mismatch alarm is declared.rw INTEGER .1.3.6.1.4.1.4515.1.3.1.19 |
slmOemTypeThis value tells the NMS the type of the OEM.
This value is read from the SEEP.ro INTEGER .1.3.6.1.4.1.4515.1.3.1.20 |
slmSysNameThis value is the shadow of the sysName object.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4515.1.3.1.21 |
slmSysLocationThis value is the shadow of the sysLocation object.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4515.1.3.1.22 |
slmSysResetPmWriting 1 to this object reset the system PM counters.rw INTEGER .1.3.6.1.4.1.4515.1.3.1.23 |
slmSysUplinkRateThis object is used to configure the rate of the Uplink.
The configured rate applies to both Uplink ports.rw Enumeration .1.3.6.1.4.1.4515.1.3.1.24 |
slmSysChassisIdThis object is used to configure the chassis-id.
Node with the same value are considered to be stacked.rw INTEGER .1.3.6.1.4.1.4515.1.3.1.25 |
slmSysNetworkPrefixThis object is used to configure the Network Prefix.
The prefix is used when the IP address of the node is
assigned automatically.
The automatic IP address of the node has the form A.x.y.z
where x.y.z is the last 3 bytes of the
MAC address 00:05:fd:x:y:z of the box.
The A is the assigned Network Prefix.
For example if the A is 10 and the MAC address is
00:05:fd:f6:55:11 the automatic IP of the node shall be
10.253.85.17.rw INTEGER .1.3.6.1.4.1.4515.1.3.1.26 |
slmSysLanIpAddrNode LAN IP Address.rw IpAddress .1.3.6.1.4.1.4515.1.3.1.27 |
slmSysLanSubnetAddrNode LAN Subnet Address.rw IpAddress .1.3.6.1.4.1.4515.1.3.1.28 |
slmPmAvailableThis value tells the NMS if the PM support is available.
The value is taken from the SEEP and can not be changed.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4515.1.3.1.29 |
slmPortsNumberThe number of ports in the system.
The value is taken from the SEEP.ro INTEGER .1.3.6.1.4.1.4515.1.3.1.30 |
slmEdfaNumberThe number of EDFA units in the system.
The value is taken from the SEEP.ro INTEGER .1.3.6.1.4.1.4515.1.3.1.31 |
slmMuxNumberThe number of MUX units in the system.
The value is taken from the SEEP.ro INTEGER .1.3.6.1.4.1.4515.1.3.1.32 |
slmOpticalSwitchExistShould an Optical Switch unit exist in the system.
The value is taken from the SEEP.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4515.1.3.1.33 |
slmReadCommunityThe SNMP read-only community.
This object should be accessible only by the Admin users of the Web.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4515.1.3.1.34 |
slmWriteCommunityThe SNMP read-write community.
This object should be accessible only by the Admin users of the Web.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4515.1.3.1.35 |
slmSysEffectiveSubnetMaskEffective Management subnetwork mask IP Address.ro IpAddress .1.3.6.1.4.1.4515.1.3.1.36 |
slmSysEffectiveIpAddrEffective Management IP Address.ro IpAddress .1.3.6.1.4.1.4515.1.3.1.37 |
slmSysLanEffectiveIpAddrEffective LAN IP Address.ro IpAddress .1.3.6.1.4.1.4515.1.3.1.38 |
slmSysLanEffectiveSubnetAddrEffective LAN subnetwork mask address.ro IpAddress .1.3.6.1.4.1.4515.1.3.1.39 |
slmSysGatewayEffectiveIpAddrEffective Gateway IP Address.ro IpAddress .1.3.6.1.4.1.4515.1.3.1.40 |
slmSysModeSystem Mode configuration (this object applies to muxponder).rw INTEGER .1.3.6.1.4.1.4515.1.3.1.41 |
slmSysTrapFormatThe format of the sent trap:
1 - the full ifIndex is sent.
2 - only the port number part of the ifIndex is sent.rw Enumeration .1.3.6.1.4.1.4515.1.3.1.42 |
slmSysTemperatureThe temperature of the PL device in Celsius.ro INTEGER .1.3.6.1.4.1.4515.1.3.1.43 |
slmNetworkMode1 - means that the LAN is define on a different vlan than the MNG ports.
2 - means that the LAN is on the same vlan and the MNG portsrw Enumeration .1.3.6.1.4.1.4515.1.3.1.44 |
slm40GConfg40(0) - No 40G ports (service ports 3..10 are disabled)
g41(1) - Single 40G Port 1 (service ports 7,8,9,10 are disabled)
g42(2) - Single 40G Port 2 (service ports 3,4,5,6 are disabled)
g43(3) - Dual 40G portsrw Enumeration .1.3.6.1.4.1.4515.1.3.1.45 |
slmRstpEnabledEnable/Disable the RSTP protocol.
Defalut value is TRUE.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4515.1.3.1.46 |
slmTopologyEnabledEnable/Disable the topology discovery protocol.
Defalut value is TRUE.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4515.1.3.1.47 |
slmAdminCommunityThe SNMP admin community.
This object should be accessible only by the Admin users of the Web.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4515.1.3.1.48 |
slmTrapCommunityThe SNMP v1/v2c trap community.
This object should be accessible only by the Admin users of the Web.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4515.1.3.1.49 |
slmSysSnmpVersionThe format of the sent trap:
3 - allow only SNMPv3 pdus.
4 - allow all pdus (coexistance mode).rw Enumeration .1.3.6.1.4.1.4515.1.3.1.50 |
slmAdmin OBJECT IDENTIFIER .1.3.6.1.4.1.4515.1.3.2 |
slmAdminTableThe admin table is used to supply the access
level for the user login. SEQUENCE OF SlmAdminEntry .1.3.6.1.4.1.4515.1.3.2.1 |
slmAdminEntryAn entry exist per user. SlmAdminEntry .1.3.6.1.4.1.4515.1.3.2.1.1 |
slmAdminLoginThe user login.rw UserLogin .1.3.6.1.4.1.4515.1.3.2.1.1.3 |
slmAdminPasswordThe user password.rw UserPassword .1.3.6.1.4.1.4515.1.3.2.1.1.4 |
slmAdminRowStatusThis object is used to create and delete rows in the
slmAdminTable.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4515.1.3.2.1.1.5 |
slmAdminAccessThe user access level.rw AdminAccess .1.3.6.1.4.1.4515.1.3.2.1.1.6 |
slmSnmpv3AuthThe user SNMP v3 authentication mode.rw Enumeration .1.3.6.1.4.1.4515.1.3.2.1.1.7 |
slmSnmpv3PrivThe user SNMP v3 privacy mode.rw Enumeration .1.3.6.1.4.1.4515.1.3.2.1.1.8 |
slmSnmpv3PasswordThe SNMP v3 Passwordrw UserPassword .1.3.6.1.4.1.4515.1.3.2.1.1.9 |
slmAuth OBJECT IDENTIFIER .1.3.6.1.4.1.4515.1.3.3 |
slmAuthTableThe authentication table is used
for creating authentication requests. SEQUENCE OF SlmAuthEntry .1.3.6.1.4.1.4515.1.3.3.1 |
slmAuthEntryThe entry is used to compute the slmAuthCommunity based
on the indexes Login and Password. Note that the table contains
no data, and when using GetNext it apears to be empty.
To compute the community the NMS should Get the field
slmAuthCommunity with the corresponding indexes. SlmAuthEntry .1.3.6.1.4.1.4515.1.3.3.1.1 |
slmAuthLoginThe user login. UserLogin .1.3.6.1.4.1.4515.1.3.3.1.1.1 |
slmAuthPasswordThe user password. UserPassword .1.3.6.1.4.1.4515.1.3.3.1.1.2 |
slmAuthCommunityThe user community name correponds to slmAuthLogin and
slmAuthPassword and which defines user'a access scope.
The value of this object is available for reading only
after the the first three colunms have been filledro UserCommunity .1.3.6.1.4.1.4515.1.3.3.1.1.3 |
slmLogin OBJECT IDENTIFIER .1.3.6.1.4.1.4515.1.3.4 |
slmTrap OBJECT IDENTIFIER .1.3.6.1.4.1.4515.1.3.5 |
slmTrapDestTableA list of trap destination entries. SEQUENCE OF SlmTrapDestEntry .1.3.6.1.4.1.4515.1.3.5.1 |
slmTrapDestEntryThis entry includes a destination IP address to which to send
traps for this community. An entry in the table is created by
the NMS.
In order to keep the entry in the table the management should
refresh the entry periodicaly. Otherwise it will be deleted
by the GNE after 5 minutes. SlmTrapDestEntry .1.3.6.1.4.1.4515.1.3.5.1.1 |
slmTrapDestAddressA copy of slmTrapDestIpAddress represented as an integer.
Needed due to VxWorks failure to handle an ip address as a table index.rw Integer32 .1.3.6.1.4.1.4515.1.3.5.1.1.1 |
slmTrapDestRowStatusThis object is used to create and delete rows in the
trapDestTable.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4515.1.3.5.1.1.2 |
slmTrapDestCommunityA community to which this destination address belongs.
This entry is associated with any eventEntries in the RMON
MIB whose value of eventCommunity is equal to the value of
this object. Every time an associated event entry sends a
trap due to an event, that trap will be sent to each
address in the trapDestTable with a trapDestCommunity equal to
eventCommunity.
This object may not be modified if the associated
trapDestStatus object is equal to active(1).rw UserCommunity .1.3.6.1.4.1.4515.1.3.5.1.1.3 |
slmTrapDestProtVersionThe SNMP version of the traps which this manager expects to receive.rw Enumeration .1.3.6.1.4.1.4515.1.3.5.1.1.4 |
slmTrapUserLoginThe user login. This is used to describe to the manager
the current active login sessions. The NMS should read
this value periodicaly in order to refresh its entry, otherwise
the entry will be deleted by the GNE after a timeout of 5 minutes.rw UserLogin .1.3.6.1.4.1.4515.1.3.5.1.1.5 |
slmTrapUserAccessThe user access.rw AdminAccess .1.3.6.1.4.1.4515.1.3.5.1.1.6 |
slmTrapEnableTRUE - means that that the alarms are allowed.
FALSE - means that all alarms should not be sent for this session.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4515.1.3.5.1.1.7 |
slmTrapPortThe destination port for to send the trap.
The default value is 162.rw INTEGER .1.3.6.1.4.1.4515.1.3.5.1.1.8 |
slmTrapDestIpAddressThe address to send traps on behalf of this entry.
This object may not be modified if the associated
slmTrapDestStatus object is equal to active(1).rw IpAddress .1.3.6.1.4.1.4515.1.3.5.1.1.9 |
slmTrapLogTableA list of trap log entries. SEQUENCE OF SlmTrapLogEntry .1.3.6.1.4.1.4515.1.3.5.2 |
slmTrapLogEntryAn entry in the table keeps the log of a single trap. SlmTrapLogEntry .1.3.6.1.4.1.4515.1.3.5.2.1 |
slmTrapLogIdThe trap log id. The id increments each time a new log
entry arrives.ro Gauge32 .1.3.6.1.4.1.4515.1.3.5.2.1.1 |
slmTrapLogNameThe object id of the trap.ro OCTET STRING .1.3.6.1.4.1.4515.1.3.5.2.1.2 |
slmTrapLogTimeStampThe trap time stamp.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.4515.1.3.5.2.1.3 |
slmTrapLogParam1The first parameter of the trap.ro OCTET STRING .1.3.6.1.4.1.4515.1.3.5.2.1.4 |
slmTrapLogParam2The second parameter of the trap.ro OCTET STRING .1.3.6.1.4.1.4515.1.3.5.2.1.5 |
slmTrapLogParam3The third parameter of the trap.ro OCTET STRING .1.3.6.1.4.1.4515.1.3.5.2.1.6 |
slmTrapLogParam4The forth parameter of the trap.ro OCTET STRING .1.3.6.1.4.1.4515.1.3.5.2.1.7 |
slmTrapLogParam5The fifth parameter of the trap.ro OCTET STRING .1.3.6.1.4.1.4515.1.3.5.2.1.8 |
slmTrapLogParam6The sixth parameter of the trap.ro OCTET STRING .1.3.6.1.4.1.4515.1.3.5.2.1.9 |
slmTrapSoftwareStatusChangeA slmTrapSoftwareStatusChange trap is sent when the
value of the slmSwRevStatus of one of the directories changes. NOTIFICATION-TYPE .1.3.6.1.4.1.4515.1.3.5.4 |
slmTrapSysNameChangeA slmTrapSysNameChange trap is sent when the
value of the slmSysName is changed. NOTIFICATION-TYPE .1.3.6.1.4.1.4515.1.3.5.5 |
slmTrapSysLocationChangeA slmTrapSysLocationChange trap is sent when the
value of the slmSysLocation is changed. NOTIFICATION-TYPE .1.3.6.1.4.1.4515.1.3.5.6 |
slmSyslogDestTableA list of syslog destination entries. SEQUENCE OF SlmSyslogDestEntry .1.3.6.1.4.1.4515.1.3.5.7 |
slmSyslogDestEntryThis entry includes a destination IP addresses to which to send
log messages. SlmSyslogDestEntry .1.3.6.1.4.1.4515.1.3.5.7.1 |
slmSyslogDestAddressA copy of slmSyslogDestTable represented as an integer.
Needed due to VxWorks failure to handle an ip address as a table index.rw Integer32 .1.3.6.1.4.1.4515.1.3.5.7.1.1 |
slmSyslogDestRowStatusThis object is used to create and delete rows in the slmSyslogDestTable.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.4515.1.3.5.7.1.2 |
slmSyslogLevelThe level of log messages which this manager expects to receive.rw Enumeration .1.3.6.1.4.1.4515.1.3.5.7.1.3 |
slmSyslogPortThe destination port for to send the log message.
The default value is 514.rw INTEGER .1.3.6.1.4.1.4515.1.3.5.7.1.4 |
slmSyslogDestIpAddressThe address to send log messages on behalf of this entry.rw IpAddress .1.3.6.1.4.1.4515.1.3.5.7.1.5 |
slmLogFile OBJECT IDENTIFIER .1.3.6.1.4.1.4515.1.3.8 |
slmConfigFile OBJECT IDENTIFIER .1.3.6.1.4.1.4515.1.3.9 |
slmChPass OBJECT IDENTIFIER .1.3.6.1.4.1.4515.1.3.12 |
slmChPassTableThe table is used for changing the user passowrd. SEQUENCE OF SlmChPassEntry .1.3.6.1.4.1.4515.1.3.12.1 |
slmChPassEntryThe entry is used to set the slmChPassNewPass.
Note that the table contains no data, and when
using GetNext it apears to be empty.
To change the password, the NMS should issue a SET
command with the new password while the two indexes
equal to the old user login and password. SlmChPassEntry .1.3.6.1.4.1.4515.1.3.12.1.1 |
slmChPassLoginThe user login. UserLogin .1.3.6.1.4.1.4515.1.3.12.1.1.1 |
slmChPassOldPassThe user password. UserPassword .1.3.6.1.4.1.4515.1.3.12.1.1.2 |
slmChPassNewPassThe user password.rw UserPassword .1.3.6.1.4.1.4515.1.3.12.1.1.3 |
slmLicense OBJECT IDENTIFIER .1.3.6.1.4.1.4515.1.3.17 |
slmLicenseTableA list of License entries. SEQUENCE OF SlmLicenseEntry .1.3.6.1.4.1.4515.1.3.17.1 |
slmLicenseEntryAn entry in the table correspond to installed license. SlmLicenseEntry .1.3.6.1.4.1.4515.1.3.17.1.1 |
slmLicenseIndexThe license index.ro INTEGER .1.3.6.1.4.1.4515.1.3.17.1.1.1 |
slmLicenseExpirationThe number of seconds to expiration.
Value -1 for permanent.ro INTEGER .1.3.6.1.4.1.4515.1.3.17.1.1.2 |
slmLicenseIdThe license textro DisplayString .1.3.6.1.4.1.4515.1.3.17.1.1.3 |