SL-SFP-MIB
This MIB module describes the SFP Modules
Main OID:
slSfp.1.3.6.1.4.1.4515.1.10
159
Objects
Active
Status
9
Dependencies
Imported Objects
Objects
159 total| Object Name |
|---|
slSfpThis MIB module describes the SFP Modules MODULE-IDENTITY .1.3.6.1.4.1.4515.1.10 |
sfpConf OBJECT IDENTIFIER .1.3.6.1.4.1.4515.1.10.1 |
sfpConfigTableThe SFP configuration table.
The table defines the configuration of the SFP-1310 and
the SFP-WDM modules. SEQUENCE OF SfpConfigEntry .1.3.6.1.4.1.4515.1.10.1.1 |
sfpConfigEntryAn entry in the SFP configuration table.
The index to this table is the same as the ifIndex of the SFP.
The SFP Config Table contain and entry for each
module of a type SFP. SfpConfigEntry .1.3.6.1.4.1.4515.1.10.1.1.1 |
sfpConfigInterfaceThe Interface Index of the SFP (type=196).ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4515.1.10.1.1.1.1 |
sfpConfigXcvrIdThe identifier value specifies the physical device described by the serial information.
This value shall be included in the serial data. The defined identifier values are:
00h - Unknown or unspecified
01h - GBIC
02h - Module/connector soldered to motherboard
03h - 1310 SFP
04-0Ah - Reserved for XFP and other platforms
0Bh - DWDM SFP
80-FFh - Vendor specific.ro Enumeration .1.3.6.1.4.1.4515.1.10.1.1.1.2 |
sfpConfig1310ExtXcvrIdThe extended identifier value provides additional information about the 1310 transceiver.
The defined identifier values are:
00h GBIC definition is not specified or the GBIC
definition is not compliant with a defined
MOD_DEF. See product specification for details.
01h GBIC is compliant with MOD_DEF 1
02h GBIC is compliant with MOD_DEF 2
03h GBIC is compliant with MOD_DEF 3
04h GBIC/SFP function is defined by serial ID only
05h GBIC is compliant with MOD_DEF 5
06h GBIC is compliant with MOD_DEF 6
07h GBIC is compliant with MOD_DEF 7
08-FFh Reservedro Enumeration .1.3.6.1.4.1.4515.1.10.1.1.1.3 |
sfpConfigWdmExtXcvrIdThis field is used to distinguish between different types of DWDM transceivers and
different power and environmental classes. The defined identifier values are:
Bits 7..6: Reserved
Bits 5..4: Class of WDM
00: no WDM
01: CWDM
10: DWDM
Bits 3..2: Class of power
00: P<1W
01: [1W, 1.5W]
10: P>1.5W
11: reserved
Bits 3..2: Class of temp
00: [-5, 70C]
01: [1W, 1.5W]
10: reserved
11: Defined by Bytes 15 - 16.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.4 |
sfpConfigConnectorCodeThe identifier value specifies the physical device described by the serial information.
This value shall be included in the serial data. The defined identifier values are:
00h - Unknown or unspecified
01h - SC
02h - Fibre Channel Style 1 copper connector
03h - Fibre Channel Style 2 copper connector
04h - BNC/TNC
05h - Fibre Channel coaxial headers
06h - FiberJack
07h - LC
08h - MT-RJ
09h - MU
0Ah - SG
0Bh - Optical pigtail
0Ch - 1Fh - Reserved
20h - HSSDC II
21h - Copper Pigtail
22h - 7Fh - Reserved
80-FFh - Vendor specific.ro Enumeration .1.3.6.1.4.1.4515.1.10.1.1.1.5 |
sfpConfigInfibandComplianceThe following bit significant indicators define the Infiband interfaces
that are supported by the transceiver. The defined identifier values are:
Bits 0: 1X SX
Bits 1: 1X LX
Bits 2: 1X Copper Active
Bits 3: 1X Copper Passive.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.6 |
sfpConfigEsconComplianceThe following bit significant indicators define the ESCON interfaces
that are supported by the transceiver. The defined identifier values are:
Bits 0: ESCON MMF, 1310nm LED
Bits 1: ESCON SMF, 1310nm Laserro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.7 |
sfpConfigSonetComplianceThe following bit significant indicators define the SONET interfaces
that are supported by the transceiver. The defined identifier values are:
Bits 0: SONET reach specifier bit 1
Bits 1: SONET reach specifier bit 2
Where:
00 speed OC-3/OC-12/OC-48 Short reach - SONET SR compliant
10 speed OC-3/OC-12/OC-48 Short reach - SONET SR-1 compliant
10 speed OC-3/OC-12/OC-48 Intermediate reach - SONET IR-1 compliant
01 speed OC-3/OC-12/OC-48 Intermediate reach - SONET IR-2 compliant
10 speed OC-3/OC-12/OC-48 Long reach - SONET LR-1 compliant
01 speed OC-3/OC-12/OC-48 Long reach - SONET LR-2 compliant
11 speed OC-3/OC-12/OC-48 Long reach - SONET LR-3 compliant
Bits 2: OC-48, single mode long reach
Bits 3: OC-48, single mode inter. reach
Bits 4: OC-48, multi-mode short reach
Bits 5: OC-12, single mode long reach
Bits 6: OC-12, single mode inter. reach
Bits 7: OC-12 multi-mode short reach
Bits 8: OC-3, single mode long reach
Bits 9: OC-3, single mode inter. reach
Bits 10: OC-3, multi-mode short reach.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.8 |
sfpConfigGbeComplianceThe following bit significant indicators define the Infiband interfaces
that are supported by the transceiver. The defined identifier values are:
Bits 0: 1000BASE-T
Bits 1: 1000BASE-CX
Bits 2: 1000BASE-LX
Bits 3: 1000BASE-SX
Bits 4: 100BASE-LX/LX10
Bits 5: 100BASE-FX
Bits 6: BASE-BX10
Bits 7: BASE-PX.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.9 |
sfpConfigFcComplianceThe following bit significant indicators define the FC interfaces
that are supported by the transceiver. The defined identifier values are:
- Fibre Channel link length:
Bits 0: very long distance (V)
Bits 1: short distance (S)
Bits 2: intermediate distance (I)
Bits 3: long distance (L)
- Fibre Channel transmitter technology
Bits 4: Longwave laser (LC)
Bits 5: Electrical inter-enclosure (EL)
Bits 6: Electrical intra-enclosure (EL)
Bits 7: Shortwave laser w/o OFC (SN)
Bits 8: Shortwave laser w/ OFC (SL)
Bits 9: Longwave laser (LL)
Bits 10: Copper Active
Bits 11: Copper Passive
- Fibre Channel transmission media
Bits 12: Twin Axial Pair (TW)
Bits 13: Shielded Twisted Pair (TP)
Bits 14: Miniature Coax (MI)
Bits 15: Video Coax (TV)
Bits 16: Multi-mode, 62.5m (M6)
Bits 17: Multi-mode, 50 m (M5)
Bits 18: Single Mode (SM)
- Fibre Channel speed
Bits 19: 800 MB/Sec
Bits 20: 400 MB/Sec
Bits 21: 200 MB/Sec
Bits 22: 100 MB/Sec
Bits 23: 1200 MB/Sec
Bits 24: 1600 MB/Sec.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.10 |
sfpConfigEncodingCodeThe encoding value indicates the serial encoding mechanism that is the
nominal design target of the particular transceiver.
The value shall be contained in the serial data.
The defined encoding values are:
00h: Unspecified
01h: 8B10B
02h: 4B5B
03h: NRZ
04h: Manchester
05h: SONET Scrambled
06h -FFh: Reserved.ro Enumeration .1.3.6.1.4.1.4515.1.10.1.1.1.11 |
sfpConfigNominalBitRateThe nominal bit rate (BR, nominal) is specified in units of 100 Megabits
per second, rounded off to the nearest 100 Megabits per second.
The bit rate includes those bits necessary to encode and delimit the
signal as well as those bits carrying data information.
A value of 0 indicates that the bit rate is not specified and must be
determined from the transceiver technology.
The actual information transfer rate will depend on the encoding of the data,
as defined by the encoding value.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.12 |
sfpConfigLength9mKmAddition to EEPROM data from original GBIC definition.
This value specifies the link length that is supported by the transceiver while
operating in compliance with the applicable standards using single mode fiber.
A value of zero means that the transceiver does not support single mode
fiber or that the length information must be determined from the transceiver
technology.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.13 |
sfpConfigLength9m100mThis value specifies the link length that is supported by the transceiver
while operating in compliance with the applicable standards using
single mode fiber.
The value is in units of 100 meters. A value of 255 means that the transceiver
supports a link length greater than 25.4 km.
A value of zero means that the transceiver does not support single mode
fiber or that the length information must be determined from the transceiver
technology.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.14 |
sfpConfigLength50m10mThis value specifies the link length that is supported by the transceiver
while operating in compliance with the applicable standards using 50 micron
multi-mode fiber.
The value is in units of 10 meters. A value of 255 means that the transceiver
supports a link length greater than 2.54 km.
A value of zero means that the transceiver does not support 50 micron
multimode fiber or that the length information must be determined from the
transceiver technology.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.15 |
sfpConfigLength62m10mThis value specifies the link length that is supported by the transceiver
while operating in compliance with the applicable standards using 62.5 micron
multi-mode fiber.
The value is in units of 10 meters. A value of 255 means that the transceiver
supports a link length greater than 2.54 km.
A value of zero means that the transceiver does not support 50 micron
multimode fiber or that the length information must be determined from the
transceiver technology.
It is common for the transceiver to support both 50 micron and 62.5 micron
fiber.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.16 |
sfpConfigLengthCopper1mThis value specifies the link length that is supported by the transceiver
while operating in compliance with the applicable standards using copper cable.
The value is in units of 1 meter. A value of 255 means that the transceiver
supports a link length greater than 254 meters.
A value of zero means that the transceiver does not support copper cables
or that the length information must be determined from the
transceiver technology.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.17 |
sfpConfigMaxTempThis field defines the maximum operating case temperature the module is
rated for. The maximum case temperature is encoded as a signed two's
complement value in C, yielding a total range of -128C to +127C.
This field should be used even if a standard operating temperature class
is indicated in the Extended Indentifier Byte (Byte 1).ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.18 |
sfpConfigMinTempThis field defines the minimum operating case temperature the module is
rated for. The maximum case temperature is encoded as a signed two's
complement value in C, yielding a total range of -128C to +127C.
This field should be used even if a standard operating temperature class
is indicated in the Extended Indentifier Byte.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.19 |
sfpConfigMaxSupplyCurrentThis field defines the maximum supply current the module will consume
under worst case conditions. The maximum current is the byte value * 4mA.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.20 |
sfpConfigChannelSpacingIn the case of SFP:
This bit field value identifies the densest channel spacing
the module is compatible with and the number of channels over which the
module may be tuned by user command.
If not tunable, the number of channels is entered as 1.
The bit fields are:
Bits 7..6: Channel Spacing
00: 200 GHz (DWDM)
01: 100 GHz (DWDM)
10: 50 Ghz (DWDM)
11: Reserved
Bits 5..0: Number of channels (1 - 63).
In the case of XFP:
The value of this field is equal to the guaranteed range of laser
wavelength (+/- value) from Nominal wavelength.
(Wavelength Tol. = value/200 in nm)ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.21 |
sfpConfigVendorNameThe vendor name is a 16 character field that contains ASCII characters,
left-aligned and padded on the right with ASCII spaces (20h).
The vendor name shall be the full name of the corporation,
a commonly accepted abbreviation of the name of the corporation,
the SCSI company code for the corporation, or the stock exchange code
for the corporation.
At least one of the vendor name or the vendor OUI fields shall contain
valid serial data.ro SnmpAdminString .1.3.6.1.4.1.4515.1.10.1.1.1.22 |
sfpConfigOptionalWdmThe bits in the option field shall specify the options implemented
in the transceiver. The following bits are defined:
Bits 7: Optional Interrupt Pin Functionality Supported (1 if supported)
Bits 6..4: Pilot Tone Functionality
000b: No Pilot Tone Functionality
001b: Pilot Tone Detection Only
010b: Pilot Tone Injection Only
011b: Pilot Tone Injection and Detection
100b: Enhanched Pilot Tone Functionality
101b-111b: Reserved
Bits 3: Variable Optical Attenuator Implemented (1 if implemented)
Bits 2: Extended Transmit Power Monitoring
0: Default (SFF-8472) TX Power Monitoring
1: Extended TX Power Monitoring (+18.2 dBm max)
Bits 1: Wavelength Monitor Type in A2 Byte 106-107
0: Monitor is Wavelength
1: Monitor is Laser Temperature
Bits 0: Variable Decision Threshold (1 if implemented)ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.23 |
sfpConfigVendorOUIThe vendor organizationally unique identifier field (vendor OUI)
is a 3-byte field that contains the IEEE Company Identifier for the
vendor. A value of all zero in the 3-byte field indicates that
the Vendor OUI is unspecified.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.24 |
sfpConfigVendorPNThe vendor part number (vendor PN) is a 16-byte field that contains
ASCII characters, left-aligned and padded on the right with ASCII
spaces (20h), defining the vendor part number or product name.
A value of all zero in the 16-byte field indicates that the
vendor PN is unspecified.ro SnmpAdminString .1.3.6.1.4.1.4515.1.10.1.1.1.25 |
sfpConfigVendorRevThe vendor revision number (vendor rev) is a 4-byte field that
contains ASCII characters, left-aligned and padded on the right with
ASCII spaces (20h), defining the vendor's product revision number.
A value of all zero in the 4-byte field indicates that
the vendor PN is unspecified.ro SnmpAdminString .1.3.6.1.4.1.4515.1.10.1.1.1.26 |
sfpConfigWaveLengthIn the case of DWDM:
Nominal transmitter output wavelength in units of 0.01nm.
As an example, a wavelength of 1550.51nm would be encoded as: 155051.
In the case of 1310:
The laser wavelength is equal to the the integer value in nm with 00 at
the end.
As an example, a wavelength of 1310 would be encoded as: 131000.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.27 |
sfpConfigExtendedOptionsSpecify the bitmap options implemented in the transceiver as described in.
The bits definition is:
5 RATE_SELECT is implemented
NOTE: Lack of implemention does not indicate lack of
simultaneous compliance with multiple standard rates.
Compliance with particular standards should be determined
from Transceiver Code.
4 TX_DISABLE is implemented and disables the serial output.
3 TX_FAULT signal implemented. (See SFP MSA)
2 Loss of Signal implemented, signal inverted from standard
definition in SFP MSA.
NOTE: This is not standard SFP/GBIC behavior and should
be avoided, since non-interoperable behavior results.
1 Loss of Signal implemented, signal as defined in SFP MSA.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.28 |
sfpConfigMaxBitRateThe upper bit rate limit at which the transceiver will still meet its
specifications (BR, max) is specified in units of 1% above the nominal
bit rate.
A value of zero indicates that this field is not specified.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.29 |
sfpConfigMinBitRateThe lower bit rate limit at which the transceiver will still meet its
specifications (BR, min) is specified in units of 1% below the nominal
bit rate.
A value of zero indicates that this field is not specified.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.30 |
sfpConfigVendorSNThe vendor serial number (vendor SN) is a 16 character field that
contains ASCII characters, left-aligned and padded on the right with
ASCII spaces (20h), defining thevendor's serial number for the transceiver.
A value of all zero in the 16-byte field indicates that the vendor PN is
unspecified.ro SnmpAdminString .1.3.6.1.4.1.4515.1.10.1.1.1.31 |
sfpConfigDateCodeThe date code is an 6-byte field that contains the vendor's date
code in ASCII characters. The date code is mandatory.
The date code shall be in the format: <yy><mm><dd>.ro SnmpAdminString .1.3.6.1.4.1.4515.1.10.1.1.1.32 |
sfpConfigDiagnosticMonitoringA field with 8 single bit indicators which describe the
optional digital diagnostic features implemented in the transceiver.
Since transceivers will not necessarily implement all optional
features described in this document, the 'Enhanced Options' bit field
allows the host system to determine which functions are
available over the 2 wire serial bus.
The bits assignment is:
7 Reserved for legacy diagnostic implementations.
Must be '0' for compilance with this document.
6 Digital diagnostic monitoring implemented (described in this document).
Must be '1' for compliance with this document.
5 Internally Calibrated
4 Externally Calibrated
3 Received power measurement type 0 = OMA, 1 = Average Power
2 Address change required.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.33 |
sfpConfigEnhanceOptionsA field with 6 single bit indicators which describe the
optional digital diagnostic features implemented in the transceiver.
Since transceivers will not necessarily implement all optional features
described in this document, the 'Enhanced Options' bit field allows the
host system to determine which functions are available over the 2 wire
serial bus. A '1' indicates that the particular function is
implemented in the transceiver..
The bits assignment is:
Bits 7: Optional Alarm/warning flags implemented for all monitored quantities
Bits 6: Optional Soft TX_DISABLE control and monitoring implemented
Bits 5: Optional Soft TX_FAULT monitoring implemented
Bits 4: Optional Soft RX_LOS monitoring implemented
Bits 3: Option not enabled in DWDM.
8472- Optional Soft RATE_SELECT control and monitoring implemented
Bits 2: Option not enabled in DWDM.
8472- Optional Application Select control implemented per SFF-8079ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.34 |
sfpConfig8472ComplianceAn unsigned integer that indicates which feature set(s) are
implemented in the transceiver.
The defined values are:
0 - Digital diagnostic functionality not included or undefined.
1 - Includes functionality described in Rev 9.3 SFF-8472.
2 - Includes functionality described in Rev 9.4 SFF-8472.ro Enumeration .1.3.6.1.4.1.4515.1.10.1.1.1.35 |
sfpConfigTunableWaveLengthWavelength Tuning Control.
The availability of this function is indicated in the object sfpConfigChannelSpacing,
where number of channels greater than 1 indicates tunability.
The wavelength is set to the channel number written to this byte.
For a value of 0, channel 1 is selected. For values greater than the maximum channel number,
the maximum channel number is selected.
The object value is defaults to 1 on power-up.rw INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.36 |
sfpConfigVoaControlVariable Optical Attenuator Control.
Used to control the wavelength in tunable modules.
The availability of this function is indicated in Bit 3 of sfpConfigOptionalWdm.
The amount of attenuation set is given by the Byte value * 0.1 dB,
and thus ranges from 0 to 25.6 dB.
The object value defaults to 0 on power-up.rw INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.37 |
sfpConfigVdtControlVariable Decision Threshold Control.
Used to control the variable decision threshold function.
The availability of this function is indicated in Bit 0 of sfpConfigOptionalWdm.
The object value is a 2's complement 7 bit value (-128 - +127).
The decision threshold set is given by:
Decision Threshold = 50% + [VAL/256]*100%
The object value defaults to 0 on power-up corresponding to 50%.rw INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.38 |
sfpConfigPilotToneModulationPilot Tone Injection Modulation Depth.
When basic MSA pilot tone injection functionality is implemented
(as indicated in the Serial ID fields by bits 4-6 of of sfpConfigOptionalWdm)
Tjis object may be used by the vendor to indicate modulation
depth per unit control swing on pin 7.
The modulation depth per control swing is given by:
Modulation Depth = 0.2% * VAL / Vpp(pin7)
A value of 0 indicates that the modulation depth per input swing
is within the rangerw INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.39 |
sfpConfigCleiCodeThe COMMON LANGUAGE Equipment Code.
The CLEI code contains an intelligent
ten-character code that identifies the
telecommunications equipment.
The Clei Code resides in the SEEP of the SFP.ro DisplayString .1.3.6.1.4.1.4515.1.10.1.1.1.40 |
sfpConfigXfpExtXcvrIdThis field is used to distinguish between different types of DWDM transceivers and
different power and environmental classes. The defined identifier values are:
Bits 7..6:
00: Power Level 1 Module (1.5 W max. power dissipation.)
01: Power Level 2 Module (2.5W Max)
10: Power Level 3 Module (3.5W max. power dissipation.)
11: Power Level 4 Module (>3.5W max. power dissipation.)
Bit 5: CDR exist
0: Module with CDR function
1: Non-CDR version of XFP
Bits 5: TX ref clock is required
0: TX Ref Clock Input Required
1: TX Ref Clock Input Not Required
Bits 3: CLEI code is present
0: No CLEI code present in Table 02h
1: CLEI code present in Table 02h
Bits 2..0: Resesrvedro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.41 |
sfpConfigXfpEncodingCodeThe encoding value indicates the serial encoding mechanism that is the
nominal design target of the particular transceiver.
The value shall be contained in the serial data.
The defined encoding values are:
Bit 7: 64B/66B
Bit 6: 8B/10B
Bit 5: SONET scrambled
Bit 4: NRZ
Bit 3: RZ
Bits 2-0: Reserved.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.42 |
sfpConfigXfpMinBitRateThe minimum bit rate (BR, minimum) is specified in units of 100 Megabits
per second, rounded off to the nearest 100 Megabits per second. The bit
rate includes those bits necessary to encode and delimit the signal as well
as those bits carrying data information. A value of 0 indicates that the minimum
bit rate is not specified andmust be determined from the transceiver
technology. The actual information transfer rate will depend on the encoding
of the data, as defined by the encoding value. Specific CDR rate
support is indicated in Byte 164.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.43 |
sfpConfigXfpMaxBitRateThe maximum bit rate (BR, maximum) is specified in units of 100 Megabits
per second, rounded off to the nearest 100 Megabits per second. The
bit rate includes those bits necessary to encode and delimit the signal as
well as those bits carrying data information. A value of 0 indicates that the
maximum bit rate is not specified and must be determined from the transceiver
technology. The actual information transfer rate will depend on the
encoding of the data, as defined by the encoding value. Specific CDR rate
support is indicated in Byte 164.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.44 |
sfpConfig10GSonetComplianceThe following bit significant indicators define the SONET interfaces
that are supported by the transceiver. The defined identifier values are:
Bits 0-1: Reserved
Bits 2: I-64.5 - 1550 nm, 25 km, SM, IO
Bits 3: I-64.3 - 1550 nm, 25 km, SM, IO
Bits 4: I-64.2 - 1550 nm, 25 km, SM, IO
Bits 5: I-64.2r - 1550 nm, 2 km, SM, VSR
Bits 6: I-64.1/VSR2000-2R1/P1I1-2D1 - 1310 nm, 2 km, SM, VSR
Bits 7: I-64.1r/VSR600-2R1 - 1310 nm, 0.6 km, Laser-MM Fibre-SM, VSR
Bits 8: Reserved
Bits 9: S-64.5b - 1550 nm, 40 km, SH
Bits 10: S-64.5a - 1550 nm, 40 km, SH
Bits 11: S-64.3b
Bits 12: S-64.3a - 1550 nm, 40 km, SM, SH
Bits 13: S-64.2b - 1550 nm, 40 km, SM, SH
Bits 14: S-64.2a - 1550 nm, 40 km, SM, SH
Bits 15: S-64.1 - 1310 nm, 20 km, IO
Bits 16-17: Reserved
Bits 18: G.959.1 P1L1-2D2 - 1550 nm, SM, 80 km, LH
Bits 19: L-64.3 - 1550 nm, 80 km, LH
Bits 20: L-64.2c - 1550 nm, 80 km, LH
Bits 21: L-64.2b - 1550 nm, 80 km, LH
Bits 22: L-64.2a - 1550 nm, 80 km, LH
Bits 23: L-64.1 - 1310 nm, SM, 40 km, SH
Bits 24-28: Reserved
Bits 29: V-64.3 - 1550 nm, SM, 120 km, VL
Bits 30: V-64.2b - 1550 nm, SM, 120 km, VL
Bits 31: V-64.2a - 1550 nm, SM, 120 km, VL.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.45 |
sfpConfig10GbeComplianceThe following bit significant indicators define the 10GbE interfaces
that are supported by the transceiver. The defined identifier values are:
Bits 0: Reserved
Bits 1: 10GBASE-EW - WAN, 1550 nm, SM, ER
Bits 2: 10GBASE-LW - WAN, 1310 nm, SM, LR
Bits 3: 10GBASE-SW - WAN, 850 nm, MM, SR
Bits 4: 10GBASE-LRM (Long reach Multimode) - LAN, 1310 nm, MM, SR fiber, 0.2 km, SR
Bits 5: 10GBASE-ER (extended range) - LAN, 1550 nm, SM, 40 km, ER
Bits 6: 10GBASE-LR (Long Range) - LAN, 1310 nm, SM, 10 km, LR
Bits 7: 10GBASE-SR - LAN, 850 nm, MM, 0.3 km, SR.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.46 |
sfpConfig10GFcComplianceThe following bit significant indicators define the 10GFC interfaces
that are supported by the transceiver. The defined identifier values are:
- Fibre Channel link length:
Bits 0-3: Reserved
Bits 4: Intermediate Reach 1300 nm FP - 1310 nm, SM, IR
Bits 5: Extended Reach 1550 nm - 1550 nm, SM, ER
Bits 6: 1200-SM-LL-L - 1310 nm, SM, LR
Bits 7: 1200-MX-SN-I - 850 nm, MM, IR.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.47 |
sfpConfigXfpDeviceTechThe following bit significant indicators define the XFP device technology:
Bits 0: 0-Transmitter not Tunable 1-Transmitter Tunable
Bits 1: Detector Type: 0-PIN detector 1-APD detector
Bits 2: Cooled transmitter
Bits 3: Wavelength control: 0-No wavelength control 1-Active wavelength control
Bits 4-7: Transmitter technology:
0000b 850 nm VCSEL
0001b 1310 nm VCSEL
0010b 1550 nm VCSEL
0011b 1310 nm FP
0100b 1310 nm DFB
0101b 1550 nm DFB
0110b 1310 nm EML
0111b 1550 nm EML
1000b Copper or others
1001b 1550 nm tunable
1111b-1001b Reserved.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.48 |
sfpConfigXfpTuningSupportedIndicate the XFP tuning support:
Bit1: wavelenght (Tunable DWDM - selection in 50 pm steps)
Bit2: frequency (Tunable DWDM - selection by channel number)
For exmaple the value 0 means no support, and 3 means both.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.49 |
sfpConfigXfpDesiredChannelUser input of channel number, which is an integer 1 to N (N=Number of Channels).rw INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.50 |
sfpConfigXfpDesiredWlUser input of Wavelength setpoint (in units of 50 picometers).rw INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.51 |
sfpConfigXfpWlErrorMonitor of Current Wavelength Error(in units of 5 picometers).ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.52 |
sfpConfigXfpDesiredFreqUser input of channel number, which is an integer to N (N=Number of Channels).rw INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.53 |
sfpConfigXfpFreqErrorFrequency error reported in 16 bit signed integer with LSB=0.1 GHz.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.54 |
sfpConfigXfpDitherSupportedTx Dither Supported.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4515.1.10.1.1.1.55 |
sfpConfigXfpDitherAdminEnable/Disable the dithering function.rw Enumeration .1.3.6.1.4.1.4515.1.10.1.1.1.56 |
sfpConfigXfpCapFreqFirstThzLasers First Frequency (THz) capability.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.57 |
sfpConfigXfpCapFreqFirst10GhzLasers First Frequency (GHz*10) capability.
This value should be added to sfpConfigXfpCapFreqFirstThz.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.58 |
sfpConfigXfpCapFreqLastThzLasers Last Frequency (THz) capability.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.59 |
sfpConfigXfpCapFreqLast10GhzLasers Last Frequency (GHz*10) capability.
This value should be added to sfpConfigXfpCapFreqLastThz.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.60 |
sfpConfigXfpCapMaxSpacing10GhzLasers maximum supported grid spacing (GHz*10) capability.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.61 |
sfpConfigXfpCalibrationSupportedCalibarion Supported.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4515.1.10.1.1.1.62 |
sfpConfigXfpCalibrationEnabledEnable/Disable the calibration process.
Changing the value to Enable when a signal exist invokes an immidiate calibration process.
Changing the value to Disable returns the calibration values to defaults.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4515.1.10.1.1.1.63 |
sfpConfigCfpExtIdExtended Identifier bit fields:
Bits 7-6 - Power Class:
00b: Power Class 1 Module (o 8 W max),
01b: Power Class 2 Module (o16 W max),
10b: Power Class 3 Module (o 24 W max),
11b: Power Class 4 Module (o 32 W max).
Bits 5-4 Lane Ratio:
00b: Network lane : Host lane = 1 : n (Mux type),
01b: Network lane : Host lane = n : m (Gear Box type),
10b: Network lane : Host lane = n : n (Parallel type),
11b: Reserved
Bits 3-1 WDM Type:
000b: Non-WDM,
001b: CWDM,
010b: LANWDM,
011b: DWDM on 200G-grid,
100b: DWDM on 100G-grid,
101b: DWDM on 50G-grid,
110b: DWDM on 25G-grid,
111b: Other type WDM
Bit 0 CLEI Presence:
0: No CLEI code present,
1: CLEI code presentro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.70 |
sfpConfigCfpConnectorTypeConnector Type Code:
00h: Undefined,
01h : SC,
07h : LC,
08h : MT-RJ,
09h : MPO,
Other Codes : Reservedro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.71 |
sfpConfigCfpEthernetCodeEthernet Application Code.
00h: Undefined type,
01h: 100GE SMF 10km, 100GE-LR4,
02h: 100GE SMF 40km, 100GE-ER4,
03h: 100GE MMF 100m OM3, 100GE-SR10,
04h: For future use,
05h: 40GE SMF 10km, 40GE-LR4,
07h: 40GE MMF 100m OM3, 40GE-SR4,
For future use:
100G G.959.1 OTU4
40G G.693 SDH
40G G.693 OTU3
40G G.695 SDH
40G G.695 OTU3,
0Dh: 40GE-CR4 Copper
0Eh: 100GE-CR10 Copper,
0Fh: 40G BASE-FR,
10h~FFh: Reserved.ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.72 |
sfpConfigCfpFcCodeFiber Channel Application Code: Undefinedro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.73 |
sfpConfigCfpCopperCodeCopper Link Application Code: Undefinedro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.74 |
sfpConfigCfpSonetCodeSONET/SDH Application Code:
00h: Undefined type,
01h: VSR2000-3R2,
02h: VSR2000-3R3,
03h: VSR2000-3R5,
04h ~ 0FFh: Reservedro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.75 |
sfpConfigCfpOtnCodeOTN Application Code:
0h: Undefined type,
01h: VSR2000-3R2F,
02h: VSR2000-3R3F,
03h: VSR2000-3R5F,
04h: VSR2000-3L2F,
05h: VSR2000-3L3F,
06h: VSR2000-3L5F,
07h: C4S1-2D1 (OTL3.4),
08h: 4I1-9D1F (OTL4.4),
09h ~ 0FFh: Reservedro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.76 |
sfpConfigCfpSupportedRatesAdditional Capable Rates Supported Bitmap:
Bits 7-5 - Reserved
Bit 4 - 111.8 Gbps
Bit 3 - 103.125 Gbps
Bit 2 - 41.25 Gbps
Bit 1 - 43 Gbps
Bit 0 - 39.8 Gbpsro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.77 |
sfpConfigCfpSupportedLanesNumber of Lanes Supported:
Bits 7-4 - Number of Network Lanes
The value of 0 represents 16 network lanes supported.
The values of 1 through 15 represent the actual number of network lanes supported
Bits 3-0 - Number of Host Lanes
The value of 0 represents 16 network lanes supported.
The values of 1 through 15 represent the actual number of network lanes supportedro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.78 |
sfpConfigCfpMediaPropertiesMedia Properties bit fields:
Bits 7 - 6 Media Type:
00b: SMF ,
01b: MMF (OM3),
10b: Reserved,
11b: Copper
Bit 5 - Directionality:
0: Normal,
1: BiDi
Bit 4 Optical Multiplexing and De-multiplexing:
0: Without optical MUX/DEMUX,
1: With optical MUX/DEMUX
Bits 3 - 0 ctive Fiber per Connector:
A 4-bit unsigned number representing number of active fibers for TX and RX per connector:
0: 16 TX Lanes and 16 RX Lanes,
1: 1 TX Lane and 1 RX Lane,
4: 4 TX Lanes and 4 RX Lanes,
10: 10 TX Lanes and 10 RX Lanes,
12: 12 TX Lanes and 12 RX Lanesro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.79 |
sfpConfigCfpMaxNetworkLaneRateMaximum Network Lane Bit Rate: 8-bit value x 0.2 Gbpsro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.80 |
sfpConfigCfpMaxHostLaneRateMaximum Host Lane Bit Rate: 8-bit value x 0.2 Gbpsro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.81 |
sfpConfigCfpMaxSmFiberLengthMaximum Single Mode Optical Fiber Length:
8-bit value x 1 km for single mode fiber lengthro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.82 |
sfpConfigCfpMaxMmFiberLengthMaximum Multi-Mode Optical Fiber Length:
8-bit value x 10 m for multi-mode fiber lengthro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.83 |
sfpConfigCfpMaxCopperCableLengthMaximum Copper Cable Length:
8-bit value x 1 m for copper cable lengthro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.84 |
sfpConfigCfpMinWavelenPerActiveMinimum Wavelength per Active Fiber:
16-bit unsigned value x 0.025 nm.
(MSB is at 8012h, LSB is at 8013h)ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.85 |
sfpConfigCfpMaxWavelenPerActiveMaximum Wavelength per Active Fiber:
16-bit unsigned value x 0.025 nm.
(MSB is at 8014h, LSB is at 8015h)ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.86 |
sfpConfigCfpMaxLenOpticalWidthMaximum per Lane Optical Width:
Guaranteed range of laser wavelength.
16-bit unsigned value x 1 pm.
(MSB is at 8016h, LSB is at 8017h)ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.87 |
sfpConfigCfpSpacingThe spacing between two lanes:
0- unknown spacing
1 - 100G spacing
2 - 50G spacing
3- 25G spacingrw INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.88 |
sfpConfigQsfppEthernetCodeMaximum per Lane Optical Width:
Guaranteed range of laser wavelength.
16-bit unsigned value x 1 pm.
(MSB is at 8016h, LSB is at 8017h)ro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.100 |
sfpConfigQsfppSonetCodeThe spacing between two lanes:
0- unknown spacing
1 - 100G spacing
2 - 50G spacing
3- 25G spacingrw INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.101 |
sfpConfigCxpExtIdExtended Identifier (Byte 129):
Bits 7-5 - Power Class:
000: 0.25W max - Class 0
001: 1.0W max - Class 1
010: 1.5W max - Class 2
011: 2.5W max - Class 3
100: 4.0W max - Class 4
101: 6.0W max - Class 5
110: >6.0W - Class 6
111: Reserved
Bits 4 Tx CDR Presence:
1: Tx CDR provided
0: Otherwise
Bits 3 Rx CDR Presence:
1: Rx CDR provided;
0: Otherwiserw INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.110 |
sfpConfigCxpConnectorTypeConnector Type Code (Byte 130):
30h: Passive Copper Cable Assembly
31h: Active Copper Cable Assembly (ref. Byte 147)
32h: Active Optical Cable Assembly
33h: Optical Transceiver w/ optical connectorrw INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.111 |
sfpConfigCxpMaxSupportedRateMax per-channel bit rate (Byte 134):
Max signal rate = binary value x 100 Mb/srw INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.112 |
sfpConfigCxpNominalWavelengthWavelength/Attenuation (Bytes 135-136):
Optical: Nominal Laser Wavelength
Wavelength in nm = value / 20): e.g. 42h 04h = 16, 900, 16, 900/20 = 845 nm
Copper: Nominal attenuation of cable either to the other end (passive) or to equalizer (active)
Byte 135:
Attenuation at 2.5 GHz in dB -
00h=no info
Byte 136:
Attenuation at 5 GHz in dB -
00h=no inforw INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.113 |
sfpConfigCxpDeviceTechDevice Technology (Byte 147):
Bits 7-4 (Device Technology):
0000: 850 nm VCSEL
0001:1310 nm VCSEL
0010:1550 nm VCSEL
0011: 1310 nm FP
0100:1310 nm DFB
0101:1550 nm DFB
0110: 1310 nm EML
0111: 1550 nm EML
1000: Copper or others
11001: 1490 nm DFB
1010: Copper cable un-equalized
1011: Copper cable passive equalized
1100: Copper cable near & far end active equalizers
1101: Copper cable, far end active equalizer
1110: copper cable, near end active equalizer
1111: Reserved
Bit 3 (Wavelength Control):
0: No control
1: Active wavelength control
Bit 2 (Transmitter cooling):
0: Uncooled transmitter
1: Cooled transmitter
Bit 1 (Optical Detector):
0: P-I-N Detector
1: APD detector
Bit 0 (Optical Tunability):
0: Transmitter not tunable
1:Transmitter tunablerw INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.114 |
sfpConfigCohRxDesiredChannelUser input of RX channel number, which is an integer 1 to N (N=Number of Channels).rw INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.115 |
sfpConfigCohRxDesiredWlUser input of RX Wavelength setpoint (in units of 50 picometers).rw INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.116 |
sfpConfigCohRxDesiredFreqUser input of channel number, which is an integer to N (N=Number of Channels).rw INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.117 |
sfpConfigCohCurrentCDCurrent Chromatic Dispersion counter. Units are in ps/nmro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.118 |
sfpConfigCohCurrentOSNRCurrent SNR. Units are in 0.1dBro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.119 |
sfpConfigCohAverageOSNRAverage SNR over PM interval. Units are in 0.1dBro INTEGER .1.3.6.1.4.1.4515.1.10.1.1.1.120 |
sfpDiag OBJECT IDENTIFIER .1.3.6.1.4.1.4515.1.10.2 |
sfpDiagTableThe SFP diagnostic table.
The table defines the status and control of the alarms and warnings
of the SFP-1310 and the DWDM SFP-15xy modules. SEQUENCE OF SfpDiagEntry .1.3.6.1.4.1.4515.1.10.2.1 |
sfpDiagEntryAn entry in the SFP diagnostic table.
The index to this table is the same as the ifIndex of the SFP.
The SFP Diagnostic Table contain and entry for each
SFP module. SfpDiagEntry .1.3.6.1.4.1.4515.1.10.2.1.1 |
sfpDiagInterfaceThe Interface Index of the SFP (type=196).ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.4515.1.10.2.1.1.1 |
sfpDiagHighTempAlmThresholdThe threshold value for high temperature alarm. The value 0
means -128 Celsuis. An increment on one is equivalent to 1/256 degree,
yielding a total range of -128 to +128 Celsius.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.2 |
sfpDiagLowTempAlmThresholdThe threshold value for low temperature alarm. The value 0
means -128 Celsuis. An increment on one is equivalent to 1/256 degree,
yielding a total range of -128 to +128 Celsius..rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.3 |
sfpDiagHighTempWrnThresholdThe threshold value for high temperature warning. The value 0
means -128 Celsuis. An increment on one is equivalent to 1/256 degree,
yielding a total range of -128 to +128 Celsius.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.4 |
sfpDiagLowTempWrnThresholdThe threshold value for low temperature warning. The value 0
means -128 Celsuis. An increment on one is equivalent to 1/256 degree,
yielding a total range of -128 to +128 Celsius..rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.5 |
sfpDiagHighVoltAlmThresholdThe threshold value for high voltage alarm. The value 0
means 0 Volts. An increment on one is equivalent to 100 uVolt,
yielding a total range of +6.55 Volts.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.6 |
sfpDiagLowVoltAlmThresholdThe threshold value for low voltage alarm. The value 0
means 0 Volts. An increment on one is equivalent to 100 uVolt,
yielding a total range of +6.55 Volts.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.7 |
sfpDiagHighVoltWrnThresholdThe threshold value for high voltage warning. The value 0
means 0 Volts. An increment on one is equivalent to 100 uVolt,
yielding a total range of +6.55 Volts.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.8 |
sfpDiagLowVoltWrnThresholdThe threshold value for low voltage warning. The value 0
means 0 Volts. An increment on one is equivalent to 100 uVolt,
yielding a total range of +6.55 Volts.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.9 |
sfpDiagHighTxBiasAlmThresholdThe threshold value for high voltage alarm. The value 0
means 0 Volt. An increment on one is equivalent to 2 uA,
yielding a total range of 0 to 131 mA.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.10 |
sfpDiagLowTxBiasAlmThresholdThe threshold value for low voltage alarm. The value 0
means 0 Volts. An increment on one is equivalent to 2 uA,
yielding a total range of 0 to 131 mA.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.11 |
sfpDiagHighTxBiasWrnThresholdThe threshold value for high voltage warning. The value 0
means 0 Volt. An increment on one is equivalent to 2 uA,
yielding a total range of 0 to 131 mA.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.12 |
sfpDiagLowTxBiasWrnThresholdThe threshold value for low voltage warning. The value 0
means 0 Volts. An increment on one is equivalent to 2 uA,
yielding a total range of 0 to 131 mA.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.13 |
sfpDiagHighTxPowerAlmThresholdThe threshold value for high TX power alarm. The value 0
means 0 Volt. An increment on one is equivalent to 1 uW,
yielding a total range of 0 to 65.535 mW.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.14 |
sfpDiagLowTxPowerAlmThresholdThe threshold value for low TX power alarm. The value 0
means 0 Watts. An increment on one is equivalent to 0.1 uW,
yielding a total range of 0 to 65.535 mW.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.15 |
sfpDiagHighTxPowerWrnThresholdThe threshold value for high TX power warning. The value 0
means 0 Volt. An increment on one is equivalent to 1 uW,
yielding a total range of 0 to 65.535 mW.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.16 |
sfpDiagLowTxPowerWrnThresholdThe threshold value for low TX power warning. The value 0
means 0 Watts. An increment on one is equivalent to 0.1 uW,
yielding a total range of 0 to 65.535 mW.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.17 |
sfpDiagHighRxPowerAlmThresholdThe threshold value for high RX power alarm. The value 0
means 0 Watts. An increment on one is equivalent to 0.1 uW,
yielding a total range of 0 to 6.5535 mW.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.18 |
sfpDiagLowRxPowerAlmThresholdThe threshold value for low RX power alarm. The value 0
means 0 Volt. An increment on one is equivalent to 1 uW,
yielding a total range of 0 to 6.5535 mW.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.19 |
sfpDiagHighRxPowerWrnThresholdThe threshold value for high RX power warning. The value 0
means 0 Watts. An increment on one is equivalent to 0.1 uW,
yielding a total range of 0 to 6.5535 mW.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.20 |
sfpDiagLowRxPowerWrnThresholdThe threshold value for low RX power warning. The value 0
means 0 Volt. An increment on one is equivalent to 1 uW,
yielding a total range of 0 to 6.5535 mW.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.21 |
sfpDiagHighLaserTempAlmThresholdFor DWDM applications, the diagnostic interface report either laser
wavelength or temperature, with a given module's reporting defined
by bit 1 of the object sfpConfigOptionalWdm.
The threshold value for high laser temperature alarm. The value 0
means -128 Celsuis. An increment on one is equivalent to 1/256 degree,
yielding a total range of -128 to +128 Celsius.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.22 |
sfpDiagLowLaserTempAlmThresholdFor DWDM applications, the diagnostic interface report either laser
wavelength or temperature, with a given module's reporting defined
by bit 1 of the object sfpConfigOptionalWdm.
The threshold value for low laser temperature alarm. The value 0
means -128 Celsuis. An increment on one is equivalent to 1/256 degree,
yielding a total range of -128 to +128 Celsius.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.23 |
sfpDiagHighLaserTempWrnThresholdFor DWDM applications, the diagnostic interface report either laser
wavelength or temperature, with a given module's reporting defined
by bit 1 of the object sfpConfigOptionalWdm.
The threshold value for high laser temperature warning. The value 0
means -128 Celsuis. An increment on one is equivalent to 1/256 degree,
yielding a total range of -128 to +128 Celsius.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.24 |
sfpDiagLowLaserTempWrnThresholdFor DWDM applications, the diagnostic interface report either laser
wavelength or temperature, with a given module's reporting defined
by bit 1 of the object sfpConfigOptionalWdm.
The threshold value for low laser temperature warning. The value 0
means -128 Celsuis. An increment on one is equivalent to 1/256 degree,
yielding a total range of -128 to +128 Celsius.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.25 |
sfpDiagHighWaveLenAlmThresholdFor DWDM applications, the diagnostic interface report either laser
wavelength or temperature, with a given module's reporting defined
by bit 1 of the object sfpConfigOptionalWdm.
The threshold value for high laser temperature alarm.
The reportable wavelength range is 1000.00 - 1655.35nm with a resolution
of 0.01nm.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.26 |
sfpDiagLowWaveLenAlmThresholdFor DWDM applications, the diagnostic interface report either laser
wavelength or temperature, with a given module's reporting defined
by bit 1 of the object sfpConfigOptionalWdm.
The threshold value for low laser temperature alarm.
The reportable wavelength range is 1000.00 - 1655.35nm with a resolution
of 0.01nm.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.27 |
sfpDiagHighWaveLenWrnThresholdFor DWDM applications, the diagnostic interface report either laser
wavelength or temperature, with a given module's reporting defined
by bit 1 of the object sfpConfigOptionalWdm.
The threshold value for high laser temperature warning.
The reportable wavelength range is 1000.00 - 1655.35nm with a resolution
of 0.01nm.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.28 |
sfpDiagLowWaveLenWrnThresholdFor DWDM applications, the diagnostic interface report either laser
wavelength or temperature, with a given module's reporting defined
by bit 1 of the object sfpConfigOptionalWdm.
The threshold value for low laser temperature warning.
The reportable wavelength range is 1000.00 - 1655.35nm with a resolution
of 0.01nm.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.29 |
sfpDiagHighTecCurrAlmThresholdThe threshold value for high TEC current alarm.
The reported TEC current is defined as a positive number for cooling and
a negative number for heating starting at -3276.8.
The increments are of 0.1 steps yielding a total range of -3276.8 to +3276.7.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.30 |
sfpDiagLowTecCurrAlmThresholdThe threshold value for low TEC current alarm.
The reported TEC current is defined as a positive number for cooling and
a negative number for heating starting at -3276.8.
The increments are of 0.1 steps yielding a total range of -3276.8 to +3276.7.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.31 |
sfpDiagHighTecCurrWrnThresholdThe threshold value for high TEC current warning.
The reported TEC current is defined as a positive number for cooling and
a negative number for heating starting at -3276.8.
The increments are of 0.1 steps yielding a total range of -3276.8 to +3276.7.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.32 |
sfpDiagLowTecCurrWrnThresholdThe threshold value for low TEC current warning.
The reported TEC current is defined as a positive number for cooling and
a negative number for heating starting at -3276.8.
The increments are of 0.1 steps yielding a total range of -3276.8 to +3276.7.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.33 |
sfpDiagModuleTemperatureInternally measured module temperature. The value 0 means -128 Celsuis.
An increment on one is equivalent to 1/256 degree,
yielding a total range of -128 to +128 Celsius.
Temperature accuracy is vendor specific but must be better than +/-3
degrees Celsius over specified operating temperature and voltage.ro INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.34 |
sfpDiagSupplyVoltageInternally measured supply voltage in transceiver. The value 0 means 0 Volts.
An increment on one is equivalent to 100 uVolt,
yielding a total range of +6.55 Volts.
Accuracy is vendor specific but must be better than +/-3% of the
manufacturer's nominal value over specified operating temperature and voltage.ro INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.35 |
sfpDiagTxBiasInternally measured TX Bias Current. The value 0
means 0 Volt. An increment on one is equivalent to 2 uA,
yielding a total range of 0 to 131 mA.
Accuracy is vendor specific but must be better than +/-3dB over specified
temperature and voltage. Data is not valid when the transmitter is disabled.ro INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.36 |
sfpDiagTxOutputPowerMeasured TX output power. The value 0
means 0 Watts. An increment on one is equivalent to 0.1 uW,
yielding a total range of 0 to 6.5535 mW.
For the vendor specified wavelength, accuracy shall be better than +/-3dB
over specified temperature and voltage.ro INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.37 |
sfpDiagRxInputPowerMeasured RX input power. The value 0
means 0 Watts. An increment on one is equivalent to 0.1 uW,
yielding a total range of 0 to 6.5535 mW.
For the vendor specified wavelength, accuracy shall be better than +/-3dB
over specified temperature and voltage.ro INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.38 |
sfpDiagRxLaserTemperatureMeasured Laser Temperature.
For DWDM applications, the diagnostic interface report either laser
wavelength or temperature, with a given module's reporting defined
by bit 1 of the object sfpConfigOptionalWdm.
The value 0 means -128 Celsuis. An increment on one is equivalent
to 1/256 degree, yielding a total range of -128 to +128 Celsius.
Temperature accuracy is vendor specific but must be better than +/- 0.2
degrees Celsius over specified operating temperature and voltage.ro INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.39 |
sfpDiagRxMeasuredWavelengthMeasured Laser Wavelength.
For DWDM applications, the diagnostic interface report either laser
wavelength or temperature, with a given module's reporting defined
by bit 1 of the object sfpConfigOptionalWdm.
The wavelength is defined as:
Wavelength = 1000nm + 0.01nm * 16 bit value.
Thus, the reportable wavelength range is 1000.00 - 1655.35nm with a
resolution of 0.01nm.ro INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.40 |
sfpDiagRxTecCurrentMeasured Laser Temperature or Wavelength.
For DWDM applications, the diagnostic interface report either laser
wavelength or temperature, with a given module's reporting defined
by bit 1 of the object sfpConfigOptionalWdm.
The reported TEC current is defined as a positive number for cooling and
a negative number for heating starting at -3276.8.
The increments are of 0.1 steps yielding a total range of -3276.8 to +3276.7,
The accuracy of the TEC current monitor is vendor specific but must be
better than +/-15% of the maximum TEC current as stored in the TEC Current
High Alarm Thresholdro INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.41 |
sfpDiagAlarmsThis object indicates the Alarms of the SFP module.
The sfpDiagAlarms is a bit map represented as a sum, therefore,
it can represent multiple failures (alarms) simultaneously.
The various bit positions are:
0 Temp High Alarm Set when internal temperature exceeds high alarm level.
1 Temp Low Alarm Set when internal temperature is below low alarm level.
2 Vcc High Alarm Set when internal supply voltage exceeds high alarm level.
3 Vcc Low Alarm Set when internal supply voltage is below low alarm level.
4 TX Bias High Alarm Set when TX Bias current exceeds high alarm level.
5 TX Bias Low Alarm Set when TX Bias current is below low alarm level.
6 TX Power High Alarm Set when TX output power exceeds high alarm level.
7 TX Power Low Alarm Set when TX output power is below low alarm level.
8 RX Power High Alarm Set when Received Power exceeds high alarm level.
9 RX Power Low Alarm Set when Received Power is below low alarm level.
10 (15xy) Laser T/W High Alarm Set when laser temperature or wavelength exceeds high alarm level.
11 (15xy) Laser T/W Low Alarm Set when laser temperature or wavelength is below low alarm level.
12 (15xy) TEC Current High Alarm Set when TEC current exceeds high alarm level.
13 (15xy) TEC Current Low Alarm Set when TEC current is below low alarm level.
14 Retimer Loss Of Lock
15 Removed SFP
16 Rx Signal Detect alarm
17 Laser End of Life
18 Laser Tx Failure Indication.ro INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.42 |
sfpDiagAlarmsMaskThis object indicates the Masking of the Alarms of the SFP module.
The sfpDiagAlarmsMask is a bit map. Any of the alarm and warning flags can
be masked by writing a 1 to the corresponding bits.
The various bit positions are:
0 Temp High Wanring Set when internal temperature exceeds high warning level.
1 Temp Low Wanring Set when internal temperature is below low warning level.
2 Vcc High Wanring Set when internal supply voltage exceeds high warning level.
3 Vcc Low Wanring Set when internal supply voltage is below low warning level.
4 TX Bias High Wanring Set when TX Bias current exceeds high warning level.
5 TX Bias Low Wanring Set when TX Bias current is below low warning level.
6 TX Power High Wanring Set when TX output power exceeds high warning level.
7 TX Power Low Wanring Set when TX output power is below low warning level.
8 RX Power High Wanring Set when Received Power exceeds high warning level.
9 RX Power Low Wanring Set when Received Power is below low warning level.
10 (15xy) Laser T/W High Wanring Set when laser temperature or wavelength exceeds high warning level.
11 (15xy) Laser T/W Low Wanring Set when laser temperature or wavelength is below low warning level.
12 (15xy) TEC Current High Wanring Set when TEC current exceeds high warning level.
13 (15xy) TEC Current Low Wanring Set when TEC current is below low warning level.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.43 |
sfpDiagWarningsThis object indicates the Warnings of the SFP module.
The sfpDiagWarnings is a bit map represented as a sum, therefore,
it can represent multiple failures (alarms) simultaneously.
The various bit positions are:
0 Temp High Warning Set when internal temperature exceeds high warning level.
1 Temp Low Warning Set when internal temperature is below low warning level.
2 Vcc High Warning Set when internal supply voltage exceeds high warning level.
3 Vcc Low Warning Set when internal supply voltage is below low warning level.
4 TX Bias High Warning Set when TX Bias current exceeds high warning level.
5 TX Bias Low Warning Set when TX Bias current is below low warning level.
6 TX Power High Warning Set when TX output power exceeds high warning level.
7 TX Power Low Warning Set when TX output power is below low warning level.
8 RX Power High Warning Set when Received Power exceeds high warning level.
9 RX Power Low Warning Set when Received Power is below low warning level.
10 Laser T/W High Warning Set when laser temperature or wavelength exceeds high warning level.
11 Laser T/W Low Warning Set when laser temperature or wavelength is below low warning level.
12 TEC Current High Warning Set when TEC current exceeds high warning level.
13 TEC Current Low Warning Set when TEC current is below low warning level.ro INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.44 |
sfpDiagWarningsMaskThis object indicates the Masking of the Warnings of the SFP module.
The sfpDiagWarningsMask is a bit map. Any of the alarm and warning flags can
be masked by writing a 1 to the corresponding bits.
The various bit positions are:
0 Temp High Warning Set when internal temperature exceeds high warning level.
1 Temp Low Warning Set when internal temperature is below low warning level.
2 Vcc High Warning Set when internal supply voltage exceeds high warning level.
3 Vcc Low Warning Set when internal supply voltage is below low warning level.
4 TX Bias High Warning Set when TX Bias current exceeds high warning level.
5 TX Bias Low Warning Set when TX Bias current is below low warning level.
6 TX Power High Warning Set when TX output power exceeds high warning level.
7 TX Power Low Warning Set when TX output power is below low warning level.
8 RX Power High Warning Set when Received Power exceeds high warning level.
9 RX Power Low Warning Set when Received Power is below low warning level.
10 Laser T/W High Warning Set when laser temperature or wavelength exceeds high warning level.
11 Laser T/W Low Warning Set when laser temperature or wavelength is below low warning level.
12 TEC Current High Warning Set when TEC current exceeds high warning level.
13 TEC Current Low Warning Set when TEC current is below low warning level.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.45 |
sfpDiagConfLowRxPowerAlmThresholdConfigured threshold value for low RX power alarm.
Changing this value doen't affect the SFP and is implemented by software.
The threshold level specified in 0.1 dBm units.
The range starts with -50.0 dBm.rw INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.46 |
sfpDiagRxInputPowerFloatMeasured RX input power sepcified in floating units.
This object is used for power < -40dBm that can be achieved with SFP external calibration.
When not used this value is 0 and sfpDiagRxInputPower should be used.ro Float32TC (FLOAT-TC-MIB) .1.3.6.1.4.1.4515.1.10.2.1.1.47 |
sfpDiagCxpTxTempInternally measured Tx temperature. The value 0 means -128 Celsius.
An increment on one is equivalent to 1/256 degree,
yielding a total range of -128 to +128 Celsius
For CXP Addr 22-23 (Tx Lower Page)ro INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.50 |
sfpDiagCxpHighTxTempAlmThresholdThe threshold value for high Tx temperature alarm.
The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree,
yielding a total range of -128 to +128 Celsius
For CXP Addr 128-129 (Tx Upper Page)ro INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.51 |
sfpDiagCxpLowTxTempAlmThresholdThe threshold value for low Tx temperature alarm.
The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree,
yielding a total range of -128 to +128 Celsius
For CXP Addr 130-131 (Tx Upper Page)ro INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.52 |
sfpDiagCxpRxTempInternally measured Rx temperature. The value 0 means -128 Celsius.
An increment on one is equivalent to 1/256 degree,
yielding a total range of -128 to +128 Celsius
For CXP Addr 22-23 (Rx Lower Page)ro INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.53 |
sfpDiagCxpHighRxTempAlmThresholdThe threshold value for high Rx temperature alarm.
The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree,
yielding a total range of -128 to +128 Celsius
For CXP Addr 128-129 (Rx Upper Page)ro INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.54 |
sfpDiagCxpLowRxTempAlmThresholdThe threshold value for low Rx temperature alarm.
The value 0 means -128 Celsuis. An increment on one is equivalent to 1/256 degree,
yielding a total range of -128 to +128 Celsius
For CXP Addr 130-131 (Rx Upper Page)ro INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.55 |
sfpDiagOtdrFiberCutRangeThe OTDR calculated range to the fiber cutro INTEGER .1.3.6.1.4.1.4515.1.10.2.1.1.56 |
sfpTraps OBJECT IDENTIFIER .1.3.6.1.4.1.4515.1.10.3 |
sfpConfigChangeTrapA sfpTrapsChangeTrap trap is sent when the
content of an instance sfpConfigEntry changes. It
can be utilized by an NMS to trigger polls. NOTIFICATION-TYPE .1.3.6.1.4.1.4515.1.10.3.1 |
sfpTune OBJECT IDENTIFIER .1.3.6.1.4.1.4515.1.10.4 |