SHE-SHDSL-MIB
AI MIB Summary
The SHE-SHDSL-MIB module enables direct monitoring of HDSL2 and SHDSL physical layer parameters and line states via the embedded EOC protocol, tracking metrics such as line status, attenuation, noise margins, and error counters without requiring inter-modem management communication.
This MIB module defines a collection of objects for managing HDSL2/SHDSL lines according RFC3276. An agent may reside at either end of the line, however the MIB is designed to require no management communication between the modems beyond that inherent in the low-level EOC line protocol as defined in ANSI T1E1.4/2000-006 (for HDSL2 lines), or in ITU G.991.2 (for SHDSL lines). Adapted to support RFC 4319.
Main OID:
sheShdslMib.1.3.6.1.4.1.231.7.1.2.2.1.12
461
Objects
Active
Status
9
Dependencies
Imported Objects
Objects
461 total| Object Name |
|---|
sheShdslMibThis MIB module defines a collection of objects for managing HDSL2/SHDSL lines according RFC3276. An agent may reside at either end of the line, however the MIB is designed to require no management communication between the modems beyond that inherent in the low-level EOC line protocol as defined in ANSI T1E1.4/2000-006 (for HDSL2 lines), or in ITU G.991.2 (for SHDSL lines). Adapted to support RFC 4319. MODULE-IDENTITY .1.3.6.1.4.1.231.7.1.2.2.1.12 |
sheShdslLineMIB OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1 |
sheShdslMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2 |
sheShdslCapabilityGroup OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.1 |
sheShdslCapabilityLineTxCapThis bitmap specifies the transmission modes that the STU-C is capable of supporting. Right now, support for Annex A (q9921PotsNonOverlapped(2) and q9921PotsOverlapped(3)) is present. This value depends on the DSL PHY firmware present on Columbia MxU.ro SheHdsl2ShdslTransmissionModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.1.1 |
sheShdslLineStatusTableThis MO is proprietary extension of RFC 3276 MIB and contains the proprietary line status. The table will only be supported for interfaces of iftype sdsl (96)! SEQUENCE OF SheShdslLineStatusEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2 |
sheShdslLineStatusEntryAn entry (conceptual row) in the dsShdslLineStatusTable. The Table is indexed by ifIndex. The table will only be supported for interfaces of iftype sdsl (96)! SheShdslLineStatusEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1 |
sheShdslOpStateThis object identifies the high level operational state for the STU.ro SheShdslOpStateType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.1 |
sheShdslStartProgressThis object identifies the current detailed operational state of the STU.ro SheShdslStartProgressType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.2 |
sheShdslFwReleaseTransceiver firmware release number.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.3 |
sheShdslLineSwapThis object indicates if the physical lines are swapped, i.e., logical channel A is connected to physical channel B. This applies to 4-wire operation only.ro SheShdslLineSwapType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.4 |
sheShdslRmtCountryCodeThis object provides the country code word, as defined in ITU-T G.991.2, for the STU at the other end of the loop. GlobespanVirata sets this to USA.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.5 |
sheShdslRmtEncoderAThis object identifies the 21-bit value corresponding to encoder coefficient A, as defined in ITU-T G.991.2, for the STU at the other end of the loop.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.6 |
sheShdslRmtEncoderBThis object identifies the 21-bit value corresponding to encoder coefficient B, as defined in ITU-T G.991.2, for the STU at the other end of the loop.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.7 |
sheShdslRmtProviderCodeThis object identifies the provider code word, as defined in ITU-T G.991.2, for the STU at the other end of the loop.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.8 |
sheShdslLocDetectThis object is used to determine if carrier has been lost.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.9 |
sheShdslTxPowerThis object identifies the local STU transmit power in tenths of a dBm.ro Unsigned32 UNITS "tenths of dBm" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.10 |
sheShdslFramerSyncThis object returns information regarding the framer synchronization status.ro SheShdslFramerSyncType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.11 |
sheShdslRmtTomDataThis object provides vendor-provided data, as defined in ITU-T G.991.2, for the STU at the other end of the loop.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.12 |
sheShdslDriftAlarmThis object identifies if the receive clock is in or out of range.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.13 |
sheShdslReceiverGainThis object provides the total receiver gain in dB.ro Unsigned32 UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.14 |
sheShdslBertErrorThis object provides the count of bit errors since the last time the object was read, as well as the type of synchronization.ro SheShdslBertErrorType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.15 |
sheShdslFramerOHAndDefectsThis object returns overhead data. The four least significant bits contain the overhead data in the following format: bit 0 is losd, bit 1 is sega, bit 2 is ps, and bit 3 is segd.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.16 |
sheShdslRmtFwVersionThis object provides the transceiver firmware release number of the STU at the other end of the loop.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.17 |
sheShdslUtopiaCellDelineationThis object indicates whether cell delineation has been found.ro SheShdslUtopiaCellDelineationType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.18 |
sheShdslUtopiaRxCellCntThis object indicates the number of UTOPIA cells received since the last time the object has been called. The maximum value is 0xFFFF.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.19 |
sheShdslUtopiaCellDropCntThis object indicates the number of UTOPIA cells dropped since the last time the object has been called. The maximum value is 0xFF.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.20 |
sheShdslUtopiaRxHecErrorCntThis object indicates the number of UTOPIA cells with HEC errors since the last time the object has been called. The maximum value is 0xFF.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.21 |
sheShdslUtopiaTxCellCntThis object indicates the number of UTOPIA cells transmitted since the last time the object has been called. The maximum value is 0xFFFF.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.22 |
sheShdslRmtNsfCusIdThis object returns the customer identification that was sent by the STU at the other end of the loop.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.23 |
sheShdslRmtNsfCusDataThis object returns non-standard format customer data that was sent by the STU at the other end of the loop.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.24 |
sheShdslLocalHandshakeThis object provides a way to see what capabilities are supported by the local STU. A total of 26 handshake parameters are supported.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.25 |
sheShdslRemoteHandshakeThis object provides a way to see what capabilities are supported by the STU at the other end of the loop. A total of 26 handshake parameters are supported.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.26 |
sheShdslActualHandshakeThis object provides the results of capabilities exchanged during handshake. A total of 26 handshake parameters are supported.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.27 |
sheShdslRmtTxPowerThis object provides the transmit power of the STU at the other end of the loop.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.28 |
sheShdslRmtPowerBackoffThis object indicates whether power backoff is enabled or disabled at the STU at the other end of the loop.ro SheShdslRmtPowerBackoffType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.29 |
sheShdslAutoRetrainCountThis object indicates the number of automatic retrains. This counter is only reset when a startup is initiated.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.30 |
sheShdslEocStateThis object provides status information about the eoc stage.ro SheShdslEocStateType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.31 |
sheShdslFramerOneSecondCntThis object provides CRC, SEGA, and LOSW defect one second error counts, and should be called every second.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.32 |
sheShdslNtrFaultThis object identifies the Network Timing Recovery Fault.ro SheShdslNtrFaultType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.33 |
sheShdslCpeMasterCoreThe CPE master Core.ro SheShdslCpeMasterCoreType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.34 |
sheShdslParametricTestResultIndicates the Result of the Parametric Test conducted on the Xcvr.ro SheShdslParametricTestResultType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.35 |
sheShdslParametricTestArrayConexant parameter that indicates the Parametric Test Array.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.36 |
sheShdslStartUpInfoThis conexant parameter indicates the startup mode, whether the lines comes up in bis mode or legacy mode (non bis).ro SheShdslStartUpInfoType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.37 |
sheShdslBisModeLocalHandshakeThis conexant parameter provides a way to see what rates are supported by the local STU in the form of tuples.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.38 |
sheShdslBisModeRemoteHandshakeThis conexant parameter provides a way to see what rates are supported by the STU at other end of the loop in the form of tuples.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.39 |
sheShdslBisModeActualHandshakeThis conexant parametetr provides the results of rates exchanged during handshake in the form of tuples.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.2.1.40 |
sheShdslLineParamsTableThis MO is proprietary extension of RFC 3276 MIB and contains the proprietary line parameters. The table will only be supported for interfaces of iftype sdsl (96)! SEQUENCE OF SheShdslLineParamsEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3 |
sheShdslLineParamsEntryAn entry (conceptual row) in the dsShdslLineParamsTable. The Table is indexed by ifIndex. The table will only be supported for interfaces of iftype sdsl (96)! SheShdslLineParamsEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1 |
sheShdslActionThis object specifies actions that are used to control transceiver operation.ro SheSdslActionType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.1 |
sheShdslModeThis object specifies the operational mode of the transceiver.ro SheShdslModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.2 |
sheShdslPowerScaleThis object is used to compensate for minor differences in transmit power between designs.ro SheShdslPowerScaleType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.3 |
sheShdslEncodeCoeffAThis object determines the value of encoder coefficient A, as defined in ITU-T G.991.2.ro SheShdslEncodeCoeffAType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.4 |
sheShdslEncodeCoeffBThis object determines the value of encoder coefficient B, as defined in ITU-T G.991.2ro SheShdslEncodeCoeffBType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.5 |
sheShdslTxEOCBufferLenThis object determines the number of bytes of EOC data that is buffered by the DSP in the transmit direction.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.6 |
sheShdslRxEOCBufferLenThis object determines the number of bytes of EOC data that is buffered by the DSP in the receive direction.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.7 |
sheShdslNTRThis object defines how network-timing recovery is performed.ro SheShdslNTRType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.8 |
sheShdslRxUpstreamFrameSyncCustomer-defined value. This object defines the upstream frame sync word.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.9 |
sheShdslRxDownstreamFrameSyncThis object defines the downstream frame sync word.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.10 |
sheShdslRxUpstreamStuffBitsCustomer-defined value. This object defines the upstream.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.11 |
sheShdslRxDownstreamStuffBitsThis object defines the downstream stuff bits.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.12 |
sheShdslInitiateThis object defines which STU initiates a startup. The default is STU-R initiates and STU-C waits.ro SheShdslInitiateType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.13 |
sheShdslFramerRxClockModeThis object determines the source of the receive clock.ro SheShdslFramerRxClockModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.14 |
sheShdslFramerRxPllModeThis object enables or disables the internal PLL.ro SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.15 |
sheShdslSerialAtmCiuBufferSizeThis object enables the user to set the size of the framer buffer for serial ATM operation.ro SheShdslSerialAtmCiuBufferSizeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.16 |
sheShdslTxFramerPulseDelayThis parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, a delay of up to 7 clock cycles can be specified for the transmit frame pulse.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.17 |
sheShdslRxFramerPulseDelayThis parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, a delay of up to 7 clock cycles can be specified for the receive frame pulse.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.18 |
sheShdslMultiFrameModeThis object specifies the multi frame operational mode of the transceiver.ro SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.19 |
sheShdslEnable4or6MbpsBitrateThis object specifies the operational state of the 4_6Mbps bit rate.ro SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.20 |
sheShdslTomDataWord1This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.21 |
sheShdslTomDataWord2This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.22 |
sheShdslTomDataWord3This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.23 |
sheShdslTomDataWord4This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.24 |
sheShdslSetReqSilenceModeThis object enables a silent mode for the STU at the opposite end of the loop for approximately one minute. During the silent period, the STU that requested the silent mode could perform whatever operations it wants and the STU at the opposite end will remain in handshake.ro SheShdslSetReqSilenceModeEnableType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.25 |
sheShdslSetIndividualRates1This item enables the user to individually enable or disable base rates for N=1 through N=16. The default is all rates enabled.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.26 |
sheShdslSetIndividualRates2This item enables the user to individually enable or disable base rates for N=17 through N=32. The default is all rates enabled.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.27 |
sheShdslSetIndividualRates3This item enables the user to individually enable or disable base rates for N=33 through N=36. The default is all rates enabled.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.28 |
sheShdslSatmCellDelineationThis object enables the user to enable or disable cell delineation for serial ATM operation. This parameter should be set before a startup.ro SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.29 |
sheShdslFramerCellDropOnErrorThis object determines whether cells are dropped, i.e., not passed to the host, or not dropped, i.e., passed to the host. This object must be set prior to startup.ro SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.30 |
sheShdslGearShiftTypeThis object specifies the Gear Shift Type.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.31 |
sheShdslHsNsfThis object enables or disables nonstandard Information fields for MP, MS, CL, and CLR messages, as defined in ITU-T G.994.1.bis.ro SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.32 |
sheShdslHsMaxBitsPerBaudThis object specifies the maximum bit per baud.ro SheShdslHsMaxBitsPerBaudType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.33 |
sheShdslHsCusIdThis object identifies the customer identification during handshaking, as described in ITU-T G.994.1.bis.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.34 |
sheShdslHsCusData0This object identifies two words of customer data during handshaking, as defined in ITU-T G.994.1.bis.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.35 |
sheShdslHsCusData1This object identifies two words of customer data during handshaking, as defined in ITU-T G.994.1.bis.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.36 |
sheShdslHsAnnexBTypeThis object allows the customer to choose between support for Annex B, Annex B with Access Network Frequency Plan (ANFP), or both.ro SheShdslHsAnnexBType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.37 |
sheShdslAutoRetrainEnables or disables auto-retrain.ro SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.38 |
sheShdslArCrcCheckEnables or disables auto-retrain based on CRC errors.ro SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.39 |
sheShdslArFramerSyncCheckEnables or disables auto-retrain based on framer synchronization.ro SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.40 |
sheShdslArSnrMarginCheckEnables or disables auto-retrain based on whether the S/N margin falls below a preset threshold.ro SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.41 |
sheShdslArCrcThresholdSets the threshold for the number of frames with CRC errors for autoretrain.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.42 |
sheShdslArSnrMarginThresholdSet the margin threshold for autoretrain.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.43 |
sheShdslArRetrainTimeSets the time over which the autoretrain parameters must be outside their normal ranges, so that an auto-retrain occurs.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.44 |
sheShdslOpStateTrapEnableEnables/disables trap indicating a change in op state.ro SheShdslEnableType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.45 |
sheShdslTxFrmrDataClkEdgeThis parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, transmit data can be sampled upon either rising or falling edge of the transmit clock.ro SheShdslClkEdgeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.46 |
sheShdslRxFrmrDataClkEdgeThis parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, receive data can be valid upon either rising or falling edge of the receive clock.ro SheShdslClkEdgeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.47 |
sheShdslTxFrmrPulseClkEdgeThis parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be active upon either rising or falling edge.ro SheShdslClkEdgeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.48 |
sheShdslRxFrmrPulseClkEdgeThis parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be active upon either rising or falling edge.ro SheShdslClkEdgeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.49 |
sheShdslTxFrmrPulseLvlThis parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be either active high (1) or active low (0).ro SheShdslPulseLvlType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.50 |
sheShdslRxFrmrPulseLvlThis parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be either active high (1) or active low (0).ro SheShdslPulseLvlType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.51 |
sheShdslFrmrOHThis object specifies framer OverHead Channel.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.52 |
sheShdslLoopAttenCrossingTrapEnableThis Parameter enables or disables the Trap for Loop Attenuation Threshold crossing.ro SheShdslEnableType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.53 |
sheShdslSNRMarginCrossingTrapEnableThis Parameter enables or disables the Trap for SNR Margin Threshold crossing.ro SheShdslEnableType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.54 |
sheShdslFramerOHAndDefectsTrapEnableThis Parameter enables or disables the Trap for Framer Overhead and Defects.ro SheShdslEnableType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.55 |
sheShdslParametricTestInputFileIndicates Name of the Input file from which to take the Mask Array Size, lower and upper mask Array. Null string means no file is specified.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.56 |
sheShdslParamHybridLossTestStartIndicates Start bin for range of bins to be measured. The default value mentioned is an indicative value only, for exact value refer to document number DO-400523-AN and DO-401163-AN.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.57 |
sheShdslParamHybridLossTestEndIndicates End bin for range of bins to be measured. The default value mentioned is an indicative value only.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.58 |
sheShdslFramerTypeThis object defines which type of data interface type is used. Note that the non-default values only apply to Conexant chips that support serial interfaces.ro SheShdslFramerType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.59 |
sheShdslAFETypeThis objects defines which AFE is being used.ro SheShdslAFEType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.60 |
sheShdslUtopiaL2TxAddressThis object selects the appropriate UTOPIA Level 2 address for the transmit interface.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.61 |
sheShdslUtopiaL2RxAddressThis object selects the appropriate UTOPIA Level 2 address for the receive interface.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.62 |
sheShdslUtopiaDataBusWidthThis parameter is used to specify width of UTOPIA data bus.ro SheShdslUtopiaDataBusWidthType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.63 |
sheShdslPAMModeThis parameter is used to configure the PAM mode value for startup.ro SheShdslPAMModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.3.1.64 |
sheShdslLineParamsControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4 |
sheShdslLineParamsControlRequestmodifyShdslLineParamsEntry a complete set of configurable parameters according the sheShdlsLinParamsControl-group.rw SheShdslControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.1 |
sheShdslLineParamsControlIndexIndex of the modified entry.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.2 |
sheShdslLineParamsControlStatusThe status of a user command.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.3 |
sheShdslLineParamsControlTimerThe maximum wait time for the manager for a long running user command.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.4 |
sheShdslLineParamsControlReqResultThe result of the last user command.ro SheShdslControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.5 |
sheShdslLineParamsControlTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.6 |
sheShdslLineParamsControlActionLook at Table.rw SheSdslActionType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.7 |
sheShdslLineParamsControlModeLook at table.rw SheShdslModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.8 |
sheShdslLineParamsControlPowerScaleLook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.9 |
sheShdslLineParamsControlEncodeCoeffALook at table.rw SheShdslEncodeCoeffAType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.10 |
sheShdslLineParamsControlEncodeCoeffBLook at table.rw SheShdslEncodeCoeffBType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.11 |
sheShdslLineParamsControlTxEOCBufferLenLook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.12 |
sheShdslLineParamsControlRxEOCBufferLenLook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.13 |
sheShdslLineParamsControlNTRLook at table.rw SheShdslNTRType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.14 |
sheShdslLineParamsControlRxUpstreamFrameSyncLook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.15 |
sheShdslLineParamsControlRxDownstreamFrameSyncLook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.16 |
sheShdslLineParamsControlRxUpstreamStuffBitsLook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.17 |
sheShdslLineParamsControlRxDownstreamStuffBitsLook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.18 |
sheShdslLineParamsControlInitiateLook at table.rw SheShdslInitiateType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.19 |
sheShdslLineParamsControlFramerRxClockModeLook at table.rw SheShdslFramerRxClockModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.20 |
sheShdslLineParamsControlFramerRxPllModeLook at table.rw SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.21 |
sheShdslLineParamsControlSerialAtmCiuBufferSizeLook at table.rw SheShdslSerialAtmCiuBufferSizeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.22 |
sheShdslLineParamsControlTxFramerPulseDelayLook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.23 |
sheShdslLineParamsControlRxFramerPulseDelayLook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.24 |
sheShdslLineParamsControlMultiFrameModeLook at table.rw SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.25 |
sheShdslLineParamsControlEnable4or6MbpsBitrateLook at table.rw SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.26 |
sheShdslLineParamsControlTomDataWord1Look at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.27 |
sheShdslLineParamsControlTomDataWord2Look at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.28 |
sheShdslLineParamsControlTomDataWord3Look at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.29 |
sheShdslLineParamsControlTomDataWord4Look at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.30 |
sheShdslLineParamsControlSetReqSilenceModeLook at table.rw SheShdslSetReqSilenceModeEnableType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.31 |
sheShdslLineParamsControlSetIndividualRates1Look at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.32 |
sheShdslLineParamsControlSetIndividualRates2Look at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.33 |
sheShdslLineParamsControlSetIndividualRates3Look at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.34 |
sheShdslLineParamsControlSatmCellDelineationLook at table.rw SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.35 |
sheShdslLineParamsControlFramerCellDropOnErrorLook at table.rw SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.36 |
sheShdslLineParamsControlGearShiftTypeLook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.37 |
sheShdslLineParamsControlHsNsfLook at table.rw SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.38 |
sheShdslLineParamsControlHsMaxBitsPerBaudLook at table.rw SheShdslHsMaxBitsPerBaudType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.39 |
sheShdslLineParamsControlHsCusIdLook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.40 |
sheShdslLineParamsControlHsCusData0Look at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.41 |
sheShdslLineParamsControlHsCusData1Look at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.42 |
sheShdslLineParamsControlHsAnnexBTypeLook at table.rw SheShdslHsAnnexBType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.43 |
sheShdslLineParamsControlAutoRetrainLook at table.rw SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.44 |
sheShdslLineParamsControlArCrcCheckLook at table.rw SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.45 |
sheShdslLineParamsControlArFramerSyncCheckLook at table.rw SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.46 |
sheShdslLineParamsControlArSnrMarginCheckLook at table.rw SheShdslEnableModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.47 |
sheShdslLineParamsControlArCrcThresholdLook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.48 |
sheShdslLineParamsControlArSnrMarginThresholdLook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.49 |
sheShdslLineParamsControlArRetrainTimeLook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.50 |
sheShdslLineParamsControlOpStateTrapEnableLook at table.rw SheShdslEnableType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.51 |
sheShdslLineParamsControlTxFrmrDataClkEdgeLook at table.rw SheShdslClkEdgeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.52 |
sheShdslLineParamsControlRxFrmrDataClkEdgeLook at table.rw SheShdslClkEdgeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.53 |
sheShdslLineParamsControlTxFrmrPulseClkEdgeLook at table.rw SheShdslClkEdgeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.54 |
sheShdslLineParamsControlRxFrmrPulseClkEdgeLook at table.rw SheShdslClkEdgeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.55 |
sheShdslLineParamsControlTxFrmrPulseLvlLook at table.rw SheShdslPulseLvlType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.56 |
sheShdslLineParamsControlRxFrmrPulseLvlLook at table.rw SheShdslPulseLvlType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.57 |
sheShdslLineParamsControlFrmrOHLook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.58 |
sheShdslLineParamsControlLoopAttenCrossingTrapEnableLook at table.rw SheShdslEnableType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.59 |
sheShdslLineParamsControlSNRMarginCrossingTrapEnableLook at table.rw SheShdslEnableType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.60 |
sheShdslLineParamsControlFramerOHAndDefectsTrapEnableLook at table.rw SheShdslEnableType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.61 |
sheShdslLineParamsControlParametricTestInputFileLook at table.rw OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.62 |
sheShdslLineParamsControlHybridLossTestStartLook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.63 |
sheShdslLineParamsControlHybridLossTestEndLook at table.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.64 |
sheShdslLineParamsControlPAMModeLook at table.rw SheShdslPAMModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.4.65 |
sheShdslSpanStatusExtnTableThis table is a proprietary extension of hdsl2ShdslSpanStatusTable. The table will only be supported for interfaces of iftype sdsl (96)! SEQUENCE OF SheShdslSpanStatusExtnEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.5 |
sheShdslSpanStatusExtnEntryAn entry (conceptual row) in the dsShdslSpanStatusExtnTable. The Table is indexed by ifIndex. The table will only be supported for interfaces of iftype sdsl (96)! SheShdslSpanStatusExtnEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.5.1 |
sheShdslStatusPMMSMaxLineRateThis object provides the maximum PMMS rate the line is capable of achievingro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.5.1.1 |
sheShdslStatus4WireHsModeContains the current 4 Wire Handshake Mode Configuredro SheShdslStatus4WireHsModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.5.1.2 |
sheShdslBondingGroupTableThis table contains a fixed set of possible bondig group entrys. This table will not longer be supported.obsolete SEQUENCE OF SheShdslBondingGroupEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.6 |
sheShdslBondingGroupEntryThis table contains a fixed set of possible bondig group entrys. Index is the ifIndex from if-table (used iftype is 143 - msdsl - multirate sdsl). Entry will be created and deleted during card create or delete for a shdsl-card. For one shdsl card with 48 shdsl lines, this table will contain 24 groups of type twoPortsBondingGroup and 12 entrys of type fourPortsBondingGroup.obsolete SheShdslBondingGroupEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.6.1 |
sheShdslBondingGroupBridgePortListPortlist for all member of this bonding group. The octet string is a list of pairs of octets each identify an sheBridgePortIndex. The least significant byte is the second octet.roobsolete OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.6.1.1 |
sheShdslBondingGroupTypeThe type descripes if this group contain 2 or 4 shdsl - lines.roobsolete SheShdslBondingGroupType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.6.1.2 |
shehdsl2ShdslMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7 |
shehdsl2ShdslSpanConfTableThis table supports overall configuration of HDSL2/SHDSL Spans. Entries in this table MUST be maintained in a persistent manner. SEQUENCE OF Shehdsl2ShdslSpanConfEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.1 |
shehdsl2ShdslSpanConfEntryAn entry in the hdsl2ShdslSpanConfTable. Each entry represents the complete Span in a single SHDSL line. It is indexed by the ifIndex of the associated HDSL2/SHDSL line. Shehdsl2ShdslSpanConfEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.1.1 |
shehdsl2ShdslSpanConfNumRepeatersThis object provisions the number of repeaters/regenerators in this HDSL2/SHDSL Span. The System will not support repeaters.ro Unsigned32 (0) UNITS "repeaters" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.1.1.1 |
shehdsl2ShdslSpanConfProfileThis object is a pointer to a span configuration profile in the hdsl2ShdslSpanConfProfileTable, which applies to this span. The value of this object is the index of the referenced profile in the hdsl2ShdslSpanConfProfileTable. Any attempt to set this object to a value that is not the value of the index for an active entry in the profile table, hdsl2ShdslSpanConfProfileTable, MUST be rejected.ro SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.1.1.2 |
shehdsl2ShdslSpanConfAlarmProfileThis object is a pointer to an Alarm configuration profile in the hdsl2ShdslEndpointAlarmConfProfileTable. The value of this object is the index of the referenced profile in the hdsl2ShdslEndpointAlarmConfProfileTable. The alarm threshold configuration in the referenced profile will be used by default for all segment endpoints in this span. Individual endpoints may override this profile by explicitly specifying some other profile in the hdsl2ShdslEndpointConfTable. By default, this object will have the value 'DEFVAL' (the index of the default profile). Any attempt to set this object to a value that is not the value of the index for an active entry in the profile table, hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected.ro SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.1.1.3 |
shehdsl2ShdslSpanConfControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.2 |
shehdsl2ShdslSpanConfControlRequestmodifyshehdsl2ShdslSpanConfEntry shehdsl2ShdslSpanConfControlNumRepeaters shehdsl2ShdslSpanConfControlProfile modifyshehdsl2ShdslSpanConfEntryAlarmProfile shehdsl2ShdslSpanConfControlAlarmProfilerw SheShdslControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.2.1 |
shehdsl2ShdslSpanConfControlIndexIndex of the modified entry.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.2.2 |
shehdsl2ShdslSpanConfControlStatusThe status of a user command.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.2.3 |
shehdsl2ShdslSpanConfControlTimerThe maximum wait time for the manager for a long running user command.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.2.4 |
shehdsl2ShdslSpanConfControlReqResultThe result of the last user command.ro SheShdslControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.2.5 |
shehdsl2ShdslSpanConfControlTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.2.6 |
shehdsl2ShdslSpanConfControlNumRepeaterslook at table.rw Unsigned32 (0) UNITS "repeaters" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.2.7 |
shehdsl2ShdslSpanConfControlProfilelook at table.rw SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.2.8 |
shehdsl2ShdslSpanConfControlAlarmProfilelook at table.rw SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.2.9 |
shehdsl2ShdslSpanStatusTableThis table provides overall status information of HDSL2/SHDSL spans. This table contains live data from equipment. As such, it is NOT persistent. SEQUENCE OF Shehdsl2ShdslSpanStatusEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.3 |
shehdsl2ShdslSpanStatusEntryAn entry in the hdsl2ShdslSpanStatusTable. Each entry represents the complete span in a single HDSL2/SHDSL line. It is indexed by the ifIndex of the associated HDSL2/SHDSL line. Shehdsl2ShdslSpanStatusEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.3.1 |
shehdsl2ShdslStatusNumAvailRepeatersContains the actual number of repeaters/regenerators discovered in this HDSL2/SHDSL span.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.3.1.1 |
shehdsl2ShdslStatusMaxAttainableLineRateContains the maximum attainable line rate in this HDSL2/SHDSL span. This object provides the maximum rate the line is capable of achieving. This is based upon measurements made during line probing. This rate includes payload (user data) and any applicable framing overhead.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.3.1.2 |
shehdsl2ShdslStatusActualLineRateContains the actual line rate in this HDSL2/SHDSL span. This should equal ifSpeed. This rate includes payload (user data) and any applicable framing overhead.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.3.1.3 |
shehdsl2ShdslStatusTransmissionModeCurrentContains the current Power Spectral Density (PSD) regional setting of the HDSL2/SHDSL span. Bit Meaning Description 1 region 1 Indicates ITU-T G.991.2 Annex A/F. 2 region 2 Indicates ITU-T G.991.2 Annex B/G.ro SheHdsl2ShdslTransmissionModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.3.1.4 |
sheShdslStatusMaxAttainablePayloadRateThis parameter contains the maximum attainable payload rate in this SHDSL span. This is based upon measurements made during line probing without including any framing overhead.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.3.1.5 |
sheShdslStatusActualPayloadRateThis parameter contains the actual payload rate in this SHDSL span. This is based upon measurements made during line probing without including any framing overhead.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.3.1.6 |
sheShdslSpanStatusPAMModulationThe parameter show the selected PAM constellation is to be used. - SELECT_16_PAM - Use 16 PAM only - SELECT_32_PAM - Use 32 PAM only Select 16Pam limits the data rates from 192 kbps to 3840 kbps Select 32Pam limits the data rates from 768 kbps to 5696 kbps This is propietary extension for interfaces of type shdsl (169) only.ro SheShdslPAMModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.3.1.7 |
shehdsl2ShdslInventoryTableThis table supports retrieval of unit inventory information available via the EOC from units in a HDSL2/SHDSL line. Entries in this table are dynamically created during the line discovery process. The life cycle for these entries is as follows: - xtu discovers a device, either a far-end xtu or an xru - an inventory table entry is created for the device - the line goes down for whatever reason - inventory table entries for unreachable devices are destroyed. As these entries are created/destroyed dynamically, they are NOT persistent. SEQUENCE OF Shehdsl2ShdslInventoryEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.4 |
shehdsl2ShdslInventoryEntryAn entry in the hdsl2ShdslInventoryTable. Each entry represents inventory information for a single unit in a HDSL2/SHDSL line. It is indexed by the ifIndex of the HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the associated unit. Shehdsl2ShdslInventoryEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.4.1 |
shehdsl2ShdslInvIndexEach entry in this table corresponds to a physical element in a HDSL2/SHDSL Span. It is based on the EOC unit addressing scheme with reference to the xtuC. SheHdsl2ShdslUnitId .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.4.1.1 |
shehdsl2ShdslInvVendorIDVendor ID as reported in an Inventory Response message.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.4.1.2 |
shehdsl2ShdslInvVendorModelNumberVendor model number as reported in an Inventory Response message.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.4.1.3 |
shehdsl2ShdslInvVendorSerialNumberVendor serial number as reported in an Inventory Response message.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.4.1.4 |
shehdsl2ShdslInvVendorEOCSoftwareVersionVendor EOC version as reported in a Discovery Response message.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.4.1.5 |
shehdsl2ShdslInvStandardVersionVersion of the HDSL2/SHDSL standard implemented, as reported in an Inventory Response message.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.4.1.6 |
shehdsl2ShdslInvVendorListNumberVendor list number as reported in an Inventory Response message.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.4.1.7 |
shehdsl2ShdslInvVendorIssueNumberVendor issue number as reported in an Inventory Response message.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.4.1.8 |
shehdsl2ShdslInvVendorSoftwareVersionVendor software version as reported in an Inventory Response message.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.4.1.9 |
shehdsl2ShdslInvEquipmentCodeEquipment code conforming to ANSI T1.213, Coded Identification of Equipment Entities.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.4.1.10 |
shehdsl2ShdslInvVendorOtherOther vendor information as reported in an Inventory Response message.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.4.1.11 |
shehdsl2ShdslInvTransmissionModeCapabilityContains the transmission mode capability of the SHDSL unit. Bit Meaning Description 1 region 1 Indicates ITU-T G.991.2 Annex A/F. 2 region 2 Indicates ITU-T G.991.2 Annex B/G.ro SheHdsl2ShdslTransmissionModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.4.1.12 |
shehdsl2ShdslEndpointConfTableThis table supports configuration parameters for segment endpoints in a HDSL2/SHDSL line. As this table is indexed by ifIndex, it MUST be maintained in a persistent manner. SEQUENCE OF Shehdsl2ShdslEndpointConfEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.5 |
shehdsl2ShdslEndpointConfEntryAn entry in the hdsl2ShdslEndpointConfTable. Each entry represents a single segment endpoint in a HDSL2/SHDSL line. It is indexed by the ifIndex of the HDSL2/SHDSL line, the UnitId of the associated unit, the side of the unit, and the wire-pair of the associated modem. Shehdsl2ShdslEndpointConfEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.5.1 |
shehdsl2ShdslEndpointSideThe side of the unit associated with this segment endpoint - Network/Customer side - as per the Hdsl2ShdslUnitSide textual convention. SheHdsl2ShdslUnitSide .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.5.1.1 |
shehdsl2ShdslEndpointWirePairThe wire-pair of the modem associated with this segment endpoint as per the Hdsl2ShdslWirePair textual convention. wirePair1(1), -> two wire wirePair2(2), -> four wire wirePair3(3), -> six wire wirePair4(4) -> eight wire SheHdsl2ShdslWirePair .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.5.1.2 |
shehdsl2ShdslEndpointAlarmConfProfileThis object configures the alarm threshold values to be used for this segment endpoint. The values are obtained from the alarm configuration profile referenced by this object. The value of this object is the index of the referenced profile in the hdsl2ShdslEndpointAlarmConfProfileTable, or NULL (a zero- length SnmpAdminString). If the value is a zero-length SnmpAdminString, the endpoint uses the default Alarm Configuration Profile for the associated span as per the hdsl2ShdslSpanConfAlarmProfile object in the hdsl2ShdslSpanConfTable. The default value of this object is a zero-length SnmpAdminString. Any attempt to set this object to a value that is not the value of the index for an active entry in the profile table, hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected.ro SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.5.1.3 |
shehdsl2ShdslEndpointConfControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.6 |
shehdsl2ShdslEndpointConfControlRequestmodifyshehdsl2ShdslEndpointConfEntryrw SheShdslControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.6.1 |
shehdsl2ShdslEndpointConfControlIndexFirst key for the modified entry. IfIndex of line.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.6.2 |
shehdsl2ShdslEndpointConfControlStatusThe status of a user command.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.6.3 |
shehdsl2ShdslEndpointConfControlTimerThe maximum wait time for the manager for a long running user command.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.6.4 |
shehdsl2ShdslEndpointConfControlReqResultThe result of the last user command.ro SheShdslControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.6.5 |
shehdsl2ShdslEndpointConfControlTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.6.6 |
shehdsl2ShdslEndpointConfControlInvIndexSecond key for modified entry.rw SheHdsl2ShdslUnitId .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.6.7 |
shehdsl2ShdslEndpointConfControlSideThird key for the modified entry.rw SheHdsl2ShdslUnitSide .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.6.8 |
shehdsl2ShdslEndpointConfControlWirePairForth key for the modified entry.rw SheHdsl2ShdslWirePair .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.6.9 |
shehdsl2ShdslEndpointConfControlAlarmProfileLook at table.rw SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.6.10 |
shehdsl2ShdslEndpointCurrTableThis table contains current status and performance information for segment endpoints in HDSL2/SHDSL Lines. As with other tables in this MIB indexed by ifIndex, entries in this table MUST be maintained in a persistent manner. SEQUENCE OF Shehdsl2ShdslEndpointCurrEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7 |
shehdsl2ShdslEndpointCurrEntryAn entry in the hdsl2ShdslEndpointCurrTable. Each entry contains status and performance information relating to a single segment endpoint. It is indexed by the ifIndex of the HDSL2/SHDSL line, the UnitId of the associated unit, the side of the unit, and the wire-pair of the associated modem. Shehdsl2ShdslEndpointCurrEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1 |
shehdsl2ShdslEndpointCurrAtnThe current loop attenuation for this endpoint as reported in a Network or Customer Side Performance Status message.ro Integer32 (-127..128) UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.1 |
shehdsl2ShdslEndpointCurrSnrMgnThe current SNR margin for this endpoint as reported in a Status Response/SNR message.ro Integer32 (-127..128) UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.2 |
shehdsl2ShdslEndpointCurrStatusContains the current state of the endpoint. This is a bitmap of possible conditions. The various bit positions are: noDefect There no defects on the line. powerBackoff Indicates enhanced Power Backoff. deviceFault Indicates a vendor-dependent diagnostic or self-test fault has been detected. dcContinuityFault Indicates vendor-dependent conditions that interfere with span powering such as short and open circuits. snrMarginAlarm Indicates that the SNR margin has dropped below the alarm threshold. loopAttenuationAlarm Indicates that the loop attenuation exceeds the alarm threshold. loswFailureAlarm Indicates a forward LOSW alarm. configInitFailure Endpoint failure during initialization due to paired endpoint not able to support requested configuration. protocolInitFailure Endpoint failure during initialization due to incompatible protocol used by the paired endpoint. noNeighborPresent Endpoint failure during initialization due to no activation sequence detected from paired endpoint. loopbackActive A loopback is currently active at this Segment Endpoint. This is intended to supplement ifOperStatus. Note that there is a 1-1 relationship between the status bits defined in this object and the notification thresholds defined elsewhere in this MIB.ro Shehdsl2ShdslEndpointCurrStatusType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.3 |
shehdsl2ShdslEndpointESCount of Errored Seconds (ES) on this endpoint since the xU was last restarted.ro Counter32 UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.4 |
shehdsl2ShdslEndpointSESCount of Severely Errored Seconds (SES) on this endpoint since the xU was last restarted.ro Counter32 UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.5 |
shehdsl2ShdslEndpointCRCanomaliesCount of CRC anomalies on this endpoint since the xU was last restarted.ro Counter32 UNITS "detected CRC Anomalies" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.6 |
shehdsl2ShdslEndpointLOSWSCount of Loss of Sync Word (LOSW) Seconds on this endpoint since the xU was last restarted.ro Counter32 UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.7 |
shehdsl2ShdslEndpointUASCount of Unavailable Seconds (UAS) on this endpoint since the xU was last restarted.ro Counter32 UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.8 |
shehdsl2ShdslEndpointCurr15MinTimeElapsedTotal elapsed seconds in the current 15-minute interval.ro SheHdsl2ShdslPerfTimeElapsed UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.9 |
shehdsl2ShdslEndpointCurr15MinESCount of Errored Seconds (ES) in the current 15-minute interval.ro PerfCurrentCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.10 |
shehdsl2ShdslEndpointCurr15MinSESCount of Severely Errored Seconds (SES) in the current 15-minute interval.ro PerfCurrentCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.11 |
shehdsl2ShdslEndpointCurr15MinCRCanomaliesCount of CRC anomalies in the current 15-minute interval.ro PerfCurrentCount UNITS "detected CRC Anomalies" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.12 |
shehdsl2ShdslEndpointCurr15MinLOSWSCount of Loss of Sync Word (LOSW) Seconds in the current 15-minute interval.ro PerfCurrentCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.13 |
shehdsl2ShdslEndpointCurr15MinUASCount of Unavailable Seconds (UAS) in the current 15-minute interval.ro PerfCurrentCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.14 |
shehdsl2ShdslEndpointCurr1DayTimeElapsedNumber of seconds that have elapsed since the beginning of the current 1-day interval.ro SheHdsl2ShdslPerfTimeElapsed UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.15 |
shehdsl2ShdslEndpointCurr1DayESCount of Errored Seconds (ES) during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.ro SheHdsl2ShdslPerfCurrDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.16 |
shehdsl2ShdslEndpointCurr1DaySESCount of Severely Errored Seconds (SES) during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.ro SheHdsl2ShdslPerfCurrDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.17 |
shehdsl2ShdslEndpointCurr1DayCRCanomaliesCount of CRC anomalies during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.ro SheHdsl2ShdslPerfCurrDayCount UNITS "detected CRC Anomalies" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.18 |
shehdsl2ShdslEndpointCurr1DayLOSWSCount of Loss of Sync Word (LOSW) Seconds during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.ro SheHdsl2ShdslPerfCurrDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.19 |
shehdsl2ShdslEndpointCurr1DayUASCount of Unavailable Seconds (UAS) during the current day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed.ro SheHdsl2ShdslPerfCurrDayCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.20 |
shehdsl2ShdslEndpointCurrTipRingReversalThis object indicates the state of the tip/ring for the wire pair. normal(1), reversed(2)ro Shehdsl2ShdslMaintTipRingReversalType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.21 |
shehdsl2ShdslEndpointCurrActivationStateThis object indicates the activation or training state of the wire pair. preActivation(1), -> PreTrain activation(2), -> Training data(3) -> Trainedro SheHdsl2ShdslActivationStateType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.7.1.22 |
shehdsl2Shdsl15MinIntervalTableThis table provides one row for each HDSL2/SHDSL endpoint performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent. SEQUENCE OF Shehdsl2Shdsl15MinIntervalEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.8 |
shehdsl2Shdsl15MinIntervalEntryAn entry in the hdsl2Shdsl15MinIntervalTable. Shehdsl2Shdsl15MinIntervalEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.8.1 |
shehdsl2Shdsl15MinIntervalNumberPerformance Data Interval number. 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional. Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.8.1.1 |
shehdsl2Shdsl15MinIntervalEndTimeThis variable indicates the time of storing this interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.8.1.2 |
shehdsl2Shdsl15MinIntervalESCount of Errored Seconds (ES) during the interval.ro PerfIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.8.1.3 |
shehdsl2Shdsl15MinIntervalSESCount of Severely Errored Seconds (SES) during the interval.ro PerfIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.8.1.4 |
shehdsl2Shdsl15MinIntervalCRCanomaliesCount of CRC anomalies during the interval.ro PerfIntervalCount UNITS "detected CRC Anomalies" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.8.1.5 |
shehdsl2Shdsl15MinIntervalLOSWSCount of Loss of Sync Word (LOSW) Seconds during the interval.ro PerfIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.8.1.6 |
shehdsl2Shdsl15MinIntervalUASCount of Unavailable Seconds (UAS) during the interval.ro PerfIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.8.1.7 |
shehdsl2Shdsl1DayIntervalTableThis table provides one row for each HDSL2/SHDSL endpoint performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent. SEQUENCE OF Shehdsl2Shdsl1DayIntervalEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.9 |
shehdsl2Shdsl1DayIntervalEntryAn entry in the hdsl2Shdsl1DayIntervalTable. Shehdsl2Shdsl1DayIntervalEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.9.1 |
shehdsl2Shdsl1DayIntervalNumberHistory Data Interval number. Interval 1 is the the most recent previous day; interval 30 is 30 days ago. Intervals 2..30 are optional. Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.9.1.1 |
shehdsl2Shdsl1DayIntervalEndTimeThis variable indicates the time of storing this interval.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.9.1.2 |
shehdsl2Shdsl1DayIntervalMoniSecsThe amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.ro SheHdsl2ShdslPerfTimeElapsed UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.9.1.3 |
shehdsl2Shdsl1DayIntervalESCount of Errored Seconds (ES) during the 1-day interval as measured by hdsl2Shdsl1DayIntervalMoniSecs.ro SheHdsl2Shdsl1DayIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.9.1.4 |
shehdsl2Shdsl1DayIntervalSESCount of Severely Errored Seconds (SES) during the 1-day interval as measured by hdsl2Shdsl1DayIntervalMoniSecs.ro SheHdsl2Shdsl1DayIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.9.1.5 |
shehdsl2Shdsl1DayIntervalCRCanomaliesCount of CRC anomalies during the 1-day interval as measured by hdsl2Shdsl1DayIntervalMoniSecs.ro SheHdsl2Shdsl1DayIntervalCount UNITS "detected CRC Anomalies" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.9.1.6 |
shehdsl2Shdsl1DayIntervalLOSWSCount of Loss of Sync Word (LOSW) Seconds during the 1-day interval as measured by hdsl2Shdsl1DayIntervalMoniSecs.ro SheHdsl2Shdsl1DayIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.9.1.7 |
shehdsl2Shdsl1DayIntervalUASCount of Unavailable Seconds (UAS) during the 1-day interval as measured by hdsl2Shdsl1DayIntervalMoniSecs.ro SheHdsl2Shdsl1DayIntervalCount UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.9.1.8 |
shehdsl2ShdslEndpointMaintTableThis table supports maintenance operations (eg. loopbacks) to be performed on HDSL2/SHDSL segment endpoints. This table contains live data from equipment. As such, it is NOT persistent. SEQUENCE OF Shehdsl2ShdslEndpointMaintEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.10 |
shehdsl2ShdslEndpointMaintEntryAn entry in the hdsl2ShdslEndpointMaintTable. Each entry corresponds to a single segment endpoint, and is indexed by the ifIndex of the HDSL2/SHDSL line, the UnitId of the associated unit and the side of the unit. Shehdsl2ShdslEndpointMaintEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.10.1 |
shehdsl2ShdslMaintLoopbackConfigThis object controls configuration of loopbacks for the associated segment endpoint. The status of the loopback is obtained via the hdsl2ShdslEndpointCurrStatus object. noLoopback(1), normalLoopback(2) is available for STU-C and STU-R. specialLoopback(3), normalLoopbackEocId9(8), specialLoopbackEocId9(9) are only available for STU-R. digitalLoopback(4) analogLoopback(5) interfaceLoopBack(6) localFramerLoopback(7) are only available for STU-C. Loopmode 2 and 3 are standard defined. All other modes are proprietary and not supported by all lines.ro Shehdsl2ShdslMaintLoopbackConfigType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.10.1.1 |
shehdsl2ShdslMaintTipRingReversalThis object indicates the state of the tip/ring pair at the associated segment endpoint. normal(1), reversed(2)ro Shehdsl2ShdslMaintTipRingReversalType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.10.1.2 |
shehdsl2ShdslMaintPowerBackOffThis object configures the receiver at the associated segment endpoint to operate in default or enhanced power backoff mode. default(1), enhanced(2) is actual not supported for STU-C disable(3) is actual not supported for STU-Rro Shehdsl2ShdslMaintPowerBackOffType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.10.1.3 |
shehdsl2ShdslMaintSoftRestartThis object enables the manager to trigger a soft restart of the modem at the associated segment endpoint. The manager may only set this object to the 'restart(2)' value, which initiates a restart. The agent will perform a restart after approximately 5 seconds. Following the 5 second period, the agent will restore the object to the 'ready(1)' state.ro Shehdsl2ShdslMaintSoftRestartType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.10.1.4 |
shehdsl2ShdslEndpointMaintControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.11 |
shehdsl2ShdslEndpointMaintControlRequestmodifyshehdsl2ShdslEndpointMaintEntryrw SheShdslControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.11.1 |
shehdsl2ShdslEndpointMaintControlIndexFirst key for the modified entry. IfIndex of line.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.11.2 |
shehdsl2ShdslEndpointMaintControlStatusThe status of a user command.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.11.3 |
shehdsl2ShdslEndpointMaintControlTimerThe maximum wait time for the manager for a long running user command.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.11.4 |
shehdsl2ShdslEndpointMaintControlReqResultThe result of the last user command.ro SheShdslControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.11.5 |
shehdsl2ShdslEndpointMaintControlTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.11.6 |
shehdsl2ShdslEndpointMaintControlInvIndexSecond key for modified entry.rw SheHdsl2ShdslUnitId .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.11.7 |
shehdsl2ShdslEndpointMaintControlSideThird key for the modified entry.rw SheHdsl2ShdslUnitSide .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.11.8 |
shehdsl2ShdslEndpointMaintControlLoopbackConfigLook at table.rw Shehdsl2ShdslMaintLoopbackConfigType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.11.9 |
shehdsl2ShdslEndpointMaintControlPowerBackOffLook at table.rw Shehdsl2ShdslMaintPowerBackOffType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.11.10 |
shehdsl2ShdslEndpointMaintControlSoftRestartLook at table.rw Shehdsl2ShdslMaintSoftRestartType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.11.11 |
shehdsl2ShdslUnitMaintTableThis table supports maintenance operations for units in a HDSL2/SHDSL line. Entries in this table MUST be maintained in a persistent manner. SEQUENCE OF Shehdsl2ShdslUnitMaintEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.12 |
shehdsl2ShdslUnitMaintEntryAn entry in the hdsl2ShdslUnitMaintTable. Each entry corresponds to a single unit, and is indexed by the ifIndex of the HDSL2/SHDSL line and the UnitId of the associated unit. Shehdsl2ShdslUnitMaintEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.12.1 |
shehdsl2ShdslMaintLoopbackTimeoutThis object configures the timeout value for loopbacks initiated at segments endpoints contained in the associated unit. A value of 0 disables the timeout.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.12.1.1 |
shehdsl2ShdslMaintUnitPowerSourceThis object indicates the DC power source being used by the associated unit. local(1), span(2)ro Shehdsl2ShdslMaintUnitPowerSourceType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.12.1.2 |
shehdsl2ShdslUnitMaintControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.13 |
shehdsl2ShdslUnitMaintControlRequestmodifyshehdsl2ShdslUnitMaintEntryrw SheShdslControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.13.1 |
shehdsl2ShdslUnitMaintControlIndexFirst key for the modified entry. IfIndex of line.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.13.2 |
shehdsl2ShdslUnitMaintControlStatusThe status of a user command.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.13.3 |
shehdsl2ShdslUnitMaintControlTimerThe maximum wait time for the manager for a long running user command.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.13.4 |
shehdsl2ShdslUnitMaintControlReqResultThe result of the last user command.ro SheShdslControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.13.5 |
shehdsl2ShdslUnitMaintControlTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.13.6 |
shehdsl2ShdslUnitMaintControlInvIndexSecond key for modified entry.rw SheHdsl2ShdslUnitId .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.13.7 |
shehdsl2ShdslUnitMaintControlLoopbackTimeoutLook at table.rw Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.13.8 |
shehdsl2ShdslSpanConfProfileTableThis table supports definitions of span configuration profiles for SHDSL lines. HDSL2 does not support these configuration options. This table MUST be maintained in a persistent manner. SEQUENCE OF Shehdsl2ShdslSpanConfProfileEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14 |
shehdsl2ShdslSpanConfProfileEntryEach entry corresponds to a single span configuration profile. Each profile contains a set of span configuration parameters. The configuration parameters in a profile are applied to those lines referencing that profile (see the hdsl2ShdslSpanConfProfile object). If an active entry is referenced in hdsl2ShdslSpanConfProfile, the entry MUST remain active until all references are removed. Shehdsl2ShdslSpanConfProfileEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1 |
shehdsl2ShdslSpanConfProfileIndexA free running index for this table.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.1 |
shehdsl2ShdslSpanConfProfileNameThis object is the unique index associated with this profile. Entries in this table are referenced via the object hdsl2ShdslSpanConfProfile in Hdsl2ShdslSpanConfEntry. This characters are not allowed: space : ?ro SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.2 |
shehdsl2ShdslSpanConfWireInterfaceThis object configures the wire-interface operation for SHDSL Lines. twoWire(1), fourWire(2), fourWireBitInterleaved(3), fourWireByteInterleaveEnhanced(4), fourWireBitInterleaveEnhanced(5), sixWire(6), eightWire(7) Interfaces of type sdsl (96) support modes 1..5 and mode 3..5 are proprietary! Interfaces of type shdsl (169) will support mode 1..2 and 6..7!ro Shehdsl2ShdslSpanConfWireInterfaceType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.3 |
shehdsl2ShdslSpanConfMinLineRateThis object configures the minimum transmission rate for the associated SHDSL Line in bits-per-second (bps). If the minimum line rate equals the maximum line rate (hdsl2ShdslSpanMaxLineRate), the line rate is considered 'fixed'. If the minimum line rate is less than the maximum line rate, the line rate is considered 'rate-adaptive'. The minimum linerate should never be higher then the maximum linerate. Note: Technical usefull minium and maximum values depend on the configured WireInterface mode: twoWire mode -> minimum should be 200 kBits -> maximum should be 5704 kBits fourWire mode -> minimum should be 400 kBits -> maximum should be 11408 kBits sixWire mode -> minimum should be 600 kBits -> maximum should be 17112 kBits eigthWire mode -> minimum should be 800 kBits -> maximum should be 22816 kBitsro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.4 |
shehdsl2ShdslSpanConfMaxLineRateThis object configures the maximum transmission rate for the associated SHDSL Line in bits-per-second (bps). If the minimum line rate equals the maximum line rate (hdsl2ShdslSpanMaxLineRate), the line rate is considered 'fixed'. If the minimum line rate is less than the maximum line rate, the line rate is considered 'rate-adaptive'. The maximum linerate should never be less then the minimum linerate. Note: Technical usefull minium and maximum values depend on the configured WireInterface mode: twoWire mode -> minimum should be 200 kBits -> maximum should be 5704 kBits fourWire mode -> minimum should be 400 kBits -> maximum should be 11408 kBits sixWire mode -> minimum should be 600 kBits -> maximum should be 17112 kBits eigthWire mode -> minimum should be 800 kBits -> maximum should be 22816 kBitsro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.5 |
shehdsl2ShdslSpanConfPSDThis object configures use of symmetric/asymmetric PSD (Power Spectral Density) Mask for the associated SHDSL Line. Support for symmetric PSD is mandatory for all supported data rates. Support for asymmetric PSD is optional. symmetric(1), asymmetric(2), r1Asymmetric(3), r2Asymmetric(4) Mode 3..4 are propietary and only supported by interfaces of type sdsl (96).ro Shehdsl2ShdslSpanConfPSDType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.6 |
shehdsl2ShdslSpanConfTransmissionModeThis object specifies the regional setting for the SHDSL line. Minimum of one bit should always be set! Bit Meaning Description 1 region 1 Indicates ITU-T G.991.2 Annex A/F. 2 region 2 Indicates ITU-T G.991.2 Annex B/G.ro SheHdsl2ShdslTransmissionModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.7 |
shehdsl2ShdslSpanConfRemoteEnabledThis object enables/disables support for remote management of the units in a SHDSL line from the STU-R via the EOC. enabled(1), disabled(2)ro SheShdslEnableType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.8 |
shehdsl2ShdslSpanConfPowerFeedingThis object enables/disables support for optional power feeding in a SHDSL line. noPower(1), powerFeed(2), wettingCurrent(3)ro Shehdsl2ShdslSpanConfPowerFeedingType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.9 |
shehdsl2ShdslSpanConfCurrCondTargetMarginDownThis object specifies the downstream current condition target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit.ro Integer32 (-10..21) UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.10 |
shehdsl2ShdslSpanConfWorstCaseTargetMarginDownThis object specifies the downstream worst case target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit.ro Integer32 (-10..21) UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.11 |
shehdsl2ShdslSpanConfCurrCondTargetMarginUpThis object specifies the upstream current condition target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit.ro Integer32 (-10..21) UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.12 |
shehdsl2ShdslSpanConfWorstCaseTargetMarginUpThis object specifies the upstream worst case target SNR margin for a SHDSL line. The SNR margin is the difference between the desired SNR and the actual SNR. Target SNR margin is the desired SNR margin for a unit.ro Integer32 (-10..21) UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.13 |
shehdsl2ShdslSpanConfUsedTargetMarginsContains indicates whether a target SNR margin is enabled or disabled. This is a bit-map of possible settings. Minimum of one bit should always be set! The various bit positions are: currCondDown current condition downstream target SNR margin enabled worstCaseDown worst case downstream target SNR margin enabled currCondUp current condition upstream target SNR margin enabled worstCaseUp worst case upstream target SNR margin enabled.ro Shehdsl2ShdslSpanConfUsedTargetMarginsType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.14 |
shehdsl2ShdslSpanConfReferenceClockThis object configures the clock reference for the STU-C in a SHDSL Line. Note: Interfaces of type sdsl (96) support only value localClk(1). Interfaces of type shdsl (169) support also the mode networkClk(2).ro SheHdsl2ShdslClockReferenceType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.15 |
shehdsl2ShdslSpanConfLineProbeEnableThis object enables/disables support for Line Probe of the units in a SHDSL line. When Line Probe is enabled, the system performs Line Probing to find the best possible rate. If Line probe is disabled, the rate adaptation phase is skipped to shorten set up time. disable(1), enable(2)ro Shehdsl2ShdslSpanConfLineProbeEnableType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.16 |
shehdsl2ShdslSpanConfPAMConstellationThe parameter allows the selection of which PAM constellation is to be used. - AUTO_PAM_SELECT - Automatic PAM selection - SELECT_16_PAM - Use 16 PAM only - SELECT_32_PAM - Use 32 PAM only Select 16Pam limits the data rates from 192 kbps to 3840 kbps Select 32Pam limits the data rates from 768 kbps to 5696 kbps +a--------------------------------------------------------+ | Soc4e-Dsl-API : SHDSL_LineTcPamSelModeGet | +---------------------------------------------------------+ | SHDSL_TcPamSelMode_t * pMode | | pointer to store current TC-PAM selection mode | ++--------------------------------------------------------+ | extented | +---------------------------------------------------------+ This is propietary extension for interfaces of type shdsl (169) only.ro SheShdslPAMModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.17 |
shehdsl2ShdslSpanConfTCLayerSupportedSpecifies the TC-Layer. Set fix to 80)/ DSL_TC_ATM. (0) - DSL_TC_ATM (1) - DSL_TC_EFM (2) - DSL_TC_HDLC +a--------------------------------------------------------+ | Soc4e-Dsl-API : DSL_SystemInterfaceConfigGet | +---------------------------------------------------------+ | DSL_SystemInterfaceConfig_t * pData | | DSL_TcLayerSelection_t | +d--------------------------------------------------------+ | Soc4e-Drv-Cmd : ACK_PMD_EndpointAlarmConfig | +x--------------------------------------------------------+ | sics <line> <nTcLayer> <nSystemIf> | +---------------------------------------------------------+ This is propietary extension for interfaces of type shdsl (169) only.ro SheHdsl2ShdslTCLayerType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.14.1.18 |
shehdsl2ShdslSpanConfProfileControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15 |
shehdsl2ShdslSpanConfProfileControlRequestcreateshehdsl2ShdslSpanConfProfile modifyshehdsl2ShdslSpanConfProfile deleteshehdsl2ShdslSpanConfProfilerw SheShdslControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.1 |
shehdsl2ShdslSpanConfProfileControlIndexKey for the modified or deleted entry. NE will choose this number during create.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.2 |
shehdsl2ShdslSpanConfProfileControlStatusThe status of a user command.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.3 |
shehdsl2ShdslSpanConfProfileControlTimerThe maximum wait time for the manager for a long running user command.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.4 |
shehdsl2ShdslSpanConfProfileControlReqResultThe result of the last user command.ro SheShdslControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.5 |
shehdsl2ShdslSpanConfProfileControlTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.6 |
shehdsl2ShdslSpanConfProfileControlProfileNameName for new profile.rw SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.7 |
shehdsl2ShdslSpanConfProfileControlWireInterfaceLook at table. twoWire(1), fourWire(2), fourWireBitInterleaved(3), fourWireByteInterleaveEnhanced(4), fourWireBitInterleaveEnhanced(5), sixWire(6), eightWire(7) Interfaces of type sdsl (96) support modes 1..5 and mode 3..5 are proprietary! Interfaces of type shdsl (169) will support mode 1..2 and 6..7!rw Shehdsl2ShdslSpanConfWireInterfaceType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.8 |
shehdsl2ShdslSpanConfProfileControlMinLineRateLook at table. Note: Technical usefull minium and maximum values depend on the configured WireInterface mode: twoWire mode -> minimum should be 200 kBits -> maximum should be 5704 kBits fourWire mode -> minimum should be 400 kBits -> maximum should be 11408 kBits sixWire mode -> minimum should be 600 kBits -> maximum should be 17112 kBits eigthWire mode -> minimum should be 800 kBits -> maximum should be 22816 kBitsrw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.9 |
shehdsl2ShdslSpanConfProfileControlMaxLineRateLook at table. Note: Technical usefull minium and maximum values depend on the configured WireInterface mode: twoWire mode -> minimum should be 200 kBits -> maximum should be 5704 kBits fourWire mode -> minimum should be 400 kBits -> maximum should be 11408 kBits sixWire mode -> minimum should be 600 kBits -> maximum should be 17112 kBits eigthWire mode -> minimum should be 800 kBits -> maximum should be 22816 kBitsrw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.10 |
shehdsl2ShdslSpanConfProfileControlPSDLook at table.rw Shehdsl2ShdslSpanConfPSDType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.11 |
shehdsl2ShdslSpanConfProfileControlTransmissionModeLook at table.rw SheHdsl2ShdslTransmissionModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.12 |
shehdsl2ShdslSpanConfProfileControlRemoteEnabledLook at table.rw SheShdslEnableType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.13 |
shehdsl2ShdslSpanConfProfileControlPowerFeedingLook at table.rw Shehdsl2ShdslSpanConfPowerFeedingType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.14 |
shehdsl2ShdslSpanConfProfileControlCurrCondTargetMarginDownLook at table.rw Integer32 (-10..21) UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.15 |
shehdsl2ShdslSpanConfProfileControlWorstCaseTargetMarginDownLook at table.rw Integer32 (-10..21) UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.16 |
shehdsl2ShdslSpanConfProfileControlCurrCondTargetMarginUpLook at table.rw Integer32 (-10..21) UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.17 |
shehdsl2ShdslSpanConfProfileControlWorstCaseTargetMarginUpLook at table.rw Integer32 (-10..21) UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.18 |
shehdsl2ShdslSpanConfProfileControlUsedTargetMarginsLook at table.rw Shehdsl2ShdslSpanConfUsedTargetMarginsType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.19 |
shehdsl2ShdslSpanConfProfileControlReferenceClockLook at table. Note: Interfaces of type sdsl (96) support only value localClk(1). Interfaces of type shdsl (169) support also the mode networkClk(2).rw SheHdsl2ShdslClockReferenceType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.20 |
shehdsl2ShdslSpanConfProfileControlLineProbeEnableLook at table.rw Shehdsl2ShdslSpanConfLineProbeEnableType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.21 |
shehdsl2ShdslSpanConfProfileControlPAMConstellationLook at table. This is propietary extension for interfaces of type shdsl (169) only.rw SheShdslPAMModeType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.22 |
shehdsl2ShdslSpanConfProfileControlTCLayerSupportedLook at table. This is propietary extension for interfaces of type shdsl (169) only.rw SheHdsl2ShdslTCLayerType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.15.23 |
shehdsl2ShdslEndpointAlarmConfProfileTableThis table supports definitions of alarm configuration profiles for HDSL2/SHDSL segment endpoints. This table MUST be maintained in a persistent manner. SEQUENCE OF Shehdsl2ShdslEndpointAlarmConfProfileEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.16 |
shehdsl2ShdslEndpointAlarmConfProfileEntryEach entry corresponds to a single alarm configuration profile. Each profile contains a set of parameters for setting alarm thresholds for various performance attributes monitored at HDSL2/SHDSL segment endpoints. Profiles may be created/deleted using the row creation/deletion mechanism via hdsl2ShdslEndpointAlarmConfProfileRowStatus. If an active entry is referenced in either hdsl2ShdslSpanConfAlarmProfile or hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain active until all references are removed. Shehdsl2ShdslEndpointAlarmConfProfileEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.16.1 |
shehdsl2ShdslEndpointAlarmConfProfileIndexA free running index for this table.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.16.1.1 |
shehdsl2ShdslEndpointAlarmConfProfileNameThis object is the unique index associated with this profile. This characters are not allowed: space : ?ro SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.16.1.2 |
shehdsl2ShdslEndpointThreshLoopAttenuationThis object configures the loop attenuation alarm threshold. When the current value of hdsl2ShdslEndpointCurrAtn reaches or exceeds this threshold, a hdsl2ShdslLoopAttenCrossing MAY be generated.ro Integer32 (-127..128) UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.16.1.3 |
shehdsl2ShdslEndpointThreshSNRMarginThis object configures the SNR margin alarm threshold. When the current value of hdsl2ShdslEndpointCurrSnrMgn reaches or drops below this threshold, a hdsl2ShdslSNRMarginCrossing MAY be generated.ro Integer32 (-127..128) UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.16.1.4 |
shehdsl2ShdslEndpointThreshESThis object configures the threshold for the number of errored seconds (ES) within any given 15-minute performance data collection interval. If the value of errored seconds in a particular 15-minute collection interval reaches/ exceeds this value, a hdsl2ShdslPerfESThresh MAY be generated. At most one notification will be sent per interval per endpoint.ro SheHdsl2ShdslPerfIntervalThreshold UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.16.1.5 |
shehdsl2ShdslEndpointThreshSESThis object configures the threshold for the number of severely errored seconds (SES) within any given 15-minute performance data collection interval. If the value of severely errored seconds in a particular 15-minute collection interval reaches/exceeds this value, a hdsl2ShdslPerfSESThresh MAY be generated. At most one notification will be sent per interval per endpoint.ro SheHdsl2ShdslPerfIntervalThreshold UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.16.1.6 |
shehdsl2ShdslEndpointThreshCRCanomaliesThis object configures the threshold for the number of CRC anomalies within any given 15-minute performance data collection interval. If the value of CRC anomalies in a particular 15-minute collection interval reaches/exceeds this value, a hdsl2ShdslPerfCRCanomaliesThresh MAY be generated. At most one notification will be sent per interval per endpoint.ro Integer32 UNITS "detected CRC Anomalies" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.16.1.7 |
shehdsl2ShdslEndpointThreshLOSWSThis object configures the threshold for the number of Loss of Sync Word (LOSW) Seconds within any given 15-minute performance data collection interval. If the value of LOSW in a particular 15-minute collection interval reaches/exceeds this value, a hdsl2ShdslPerfLOSWSThresh MAY be generated. At most one notification will be sent per interval per endpoint.ro SheHdsl2ShdslPerfIntervalThreshold UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.16.1.8 |
shehdsl2ShdslEndpointThreshUASThis object configures the threshold for the number of unavailable seconds (UAS) within any given 15-minute performance data collection interval. If the value of UAS in a particular 15-minute collection interval reaches/exceeds this value, a hdsl2ShdslPerfUASThresh MAY be generated. At most one notification will be sent per interval per endpoint.ro SheHdsl2ShdslPerfIntervalThreshold UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.16.1.9 |
shehdsl2ShdslEndpointAlarmConfProfileControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.17 |
shehdsl2ShdslEndpointAlarmConfProfileControlRequestcreateshehdsl2ShdslEndpointAlarmConfProfile modifyshehdsl2ShdslEndpointAlarmConfProfile deleteshehdsl2ShdslEndpointAlarmConfProfilerw SheShdslControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.17.1 |
shehdsl2ShdslEndpointAlarmConfProfileControlIndexKey for the modified or deleted entry. NE will choose this number during create.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.17.2 |
shehdsl2ShdslEndpointAlarmConfProfileControlStatusThe status of a user command.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.17.3 |
shehdsl2ShdslEndpointAlarmConfProfileControlTimerThe maximum wait time for the manager for a long running user command.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.17.4 |
shehdsl2ShdslEndpointAlarmConfProfileControlReqResultThe result of the last user command.ro SheShdslControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.17.5 |
shehdsl2ShdslEndpointAlarmConfProfileControlTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.17.6 |
shehdsl2ShdslEndpointAlarmConfProfileControlProfileNameName for new profile.rw SnmpAdminString .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.17.7 |
shehdsl2ShdslEndpointConfProfileControlThreshLoopAttenuationLook at table.rw Integer32 (-127..128) UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.17.8 |
shehdsl2ShdslEndpointConfProfileControlThreshSNRMarginLook at table.rw Integer32 (-127..128) UNITS "dB" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.17.9 |
shehdsl2ShdslEndpointConfProfileControlThreshESLook at table.rw SheHdsl2ShdslPerfIntervalThreshold UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.17.10 |
shehdsl2ShdslEndpointConfProfileControlThreshSESLook at table.rw SheHdsl2ShdslPerfIntervalThreshold UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.17.11 |
shehdsl2ShdslEndpointConfProfileControlThreshCRCanomaliesLook at table.rw Integer32 UNITS "detected CRC Anomalies" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.17.12 |
shehdsl2ShdslEndpointConfProfileControlThreshLOSWSLook at table.rw SheHdsl2ShdslPerfIntervalThreshold UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.17.13 |
shehdsl2ShdslEndpointConfProfileControlThreshUASLook at table.rw SheHdsl2ShdslPerfIntervalThreshold UNITS "seconds" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.7.17.14 |
shehdsl2ShdslNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8 |
shehdsl2ShdslLoopAttenCrossingThis notification indicates that the loop attenuation threshold (as per the hdsl2ShdslEndpointThreshLoopAttenuation value) has been reached/exceeded for the HDSL2/SHDSL segment endpoint. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.1 |
shehdsl2ShdslSNRMarginCrossingThis notification indicates that the SNR margin threshold (as per the hdsl2ShdslEndpointThreshSNRMargin value) has been reached/exceeded for the HDSL2/SHDSL segment endpoint. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.2 |
shehdsl2ShdslPerfESThreshThis notification indicates that the errored seconds threshold (as per the hdsl2ShdslEndpointThreshES value) has been reached/ exceeded for the HDSL2/SHDSL segment endpoint. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.3 |
shehdsl2ShdslPerfSESThreshThis notification indicates that the severely errored seconds threshold (as per the hdsl2ShdslEndpointThreshSES value) has been reached/exceeded for the HDSL2/SHDSL Segment Endpoint. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.4 |
shehdsl2ShdslPerfCRCanomaliesThreshThis notification indicates that the CRC anomalies threshold (as per the hdsl2ShdslEndpointThreshCRCanomalies value) has been reached/exceeded for the HDSL2/SHDSL Segment Endpoint. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.5 |
shehdsl2ShdslPerfLOSWSThreshThis notification indicates that the LOSW seconds threshold (as per the hdsl2ShdslEndpointThreshLOSWS value) has been reached/exceeded for the HDSL2/SHDSL segment endpoint. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.6 |
shehdsl2ShdslPerfUASThreshThis notification indicates that the unavailable seconds threshold (as per the hdsl2ShdslEndpointThreshUAS value) has been reached/exceeded for the HDSL2/SHDSL segment endpoint. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.7 |
shehdsl2ShdslSpanInvalidNumRepeatersThis notification indicates that a mismatch has been detected between the number of repeater/regenerator units configured for a HDSL2/SHDSL line via the hdsl2ShdslSpanConfNumRepeaters object and the actual number of repeater/regenerator units discovered via the EOC. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.8 |
shehdsl2ShdslLoopbackFailureThis notification indicates that an endpoint maintenance loopback command failed for an HDSL2/SHDSL segment. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.9 |
shehdsl2ShdslpowerBackoffThis notification indicates that the bit setting for powerBackoff in the hdsl2ShdslEndpointCurrStatus object for this endpoint has changed. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.10 |
shehdsl2ShdsldeviceFaultThis notification indicates that the bit setting for deviceFault in the hdsl2ShdslEndpointCurrStatus object for this endpoint has changed. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.11 |
shehdsl2ShdsldcContinuityFaultThis notification indicates that the bit setting for dcContinuityFault in the hdsl2ShdslEndpointCurrStatus object for this endpoint has changed. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.12 |
shehdsl2ShdslconfigInitFailureThis notification indicates that the bit setting for configInitFailure in the hdsl2ShdslEndpointCurrStatus object for this endpoint has changed. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.13 |
shehdsl2ShdslprotocolInitFailureThis notification indicates that the bit setting for protocolInitFailure in the hdsl2ShdslEndpointCurrStatus object for this endpoint has changed. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.14 |
shehdsl2ShdslnoNeighborPresentThis notification indicates that the bit setting for noNeighborPresent in the hdsl2ShdslEndpointCurrStatus object for this endpoint has changed. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.15 |
shehdsl2ShdslLocalPowerLossThis notification indicates impending unit failure due to loss of local power (last gasp). NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.16 |
shehdsl2ShdslAtucPerfLolThis alarm informs the link between the line card and modem is disconnected for unidentied reason, not dying gasp. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.17 |
shehdsl2ShdslAtucPerfLprThis alarm informs the link between the line card and modem is disconnected for dying gasp. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.18 |
shehdsl2ShdslAtucPerfLosThis alarm informs the link between the line card and modem is disconnected for loss of signal. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.19 |
shehdsl2ShdslAtucPerfLofThis alarm informs the link between the line card and modem is disconnected for loss of frame. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.8.20 |
sheShdslConfigurationNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.9 |
sheShdslLineParamsEntryModifiedNotification for a complete LineParamsEntry-Modify-Command. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.9.1 |
shehdsl2ShdslSpanConfEntryModifiedNotification for a complete SpanConfEntry-Modify-Command. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.9.2 |
shehdsl2ShdslSpanConfEntryAlarmProfileModifiedNotification for a complete SpanConfEntry-Modify-Command. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.9.3 |
shehdsl2ShdslEndpointConfEntryModifiedNotification for a complete EndPointConfEntry-Modify-Command. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.9.4 |
shehdsl2ShdslEndpointMaintEntryModifiedNotification for a complete EndPointMaintEntry-Modify-Command. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.9.5 |
shehdsl2ShdslUnitMaintEntryModifiedNotification for a complete UnitMaintEntry-Modify-Command. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.9.6 |
shehdsl2ShdslSpanConfProfileCreatedNotification for a complete SpanConfProfileEntry-Create-Command. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.9.7 |
shehdsl2ShdslSpanConfProfileModifiedNotification for a complete SpanConfProfileEntry-Modify-Command. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.9.8 |
shehdsl2ShdslSpanConfProfileDeletedNotification for a complete SpanConfProfileEntry-Delete-Command. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.9.9 |
shehdsl2ShdslEndpointAlarmConfProfileCreatedNotification for a complete EndPointAlarmProfileEntry-Create-Command. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.9.10 |
shehdsl2ShdslEndpointAlarmConfProfileModifiedNotification for a complete EndPointAlarmProfileEntry-Modify-Command. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.9.11 |
shehdsl2ShdslEndpointAlarmConfProfileDeletedNotification for a complete EndPointAlarmProfileEntry-Delete-Command. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.9.12 |
shehdsl2ShdslSpanConfProfileReqResultTrap for long running profile modification result. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.9.13 |
shehdsl2ShdslEndpointAlarmConfProfileReqResultTrap for long running profile modification result. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.9.14 |
sheShdslVccTpTableThe VccTp-Table. SEQUENCE OF SheShdslVccTpEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.10 |
sheShdslVccTpEntryThis table contains the VccTp-Configurations. There will be one entry for every shdsl-interface available per default. This default entry should never be deleted. SheShdslVccTpEntry .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.10.1 |
sheShdslVccTpIndexIndex for that table. The index will follow this rule: VccTpIndex = (VccTpSubLayerIndex << 4) + VccTpNumberro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.10.1.1 |
sheShdslVccTpSubLayerIndexifIndex of the underlaying shdsl-interface.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.10.1.2 |
sheShdslVccTpNumberThis is the logical number of VccTP on the corresponding interface. Maximum value is 1.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.10.1.3 |
sheShdslVccTpVpiThe VPI - Value.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.10.1.4 |
sheShdslVccTpVciThe Vci - Value.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.10.1.5 |
sheShdslVccTpOamLevelThe OAM level for loop test on VP/VC level. Valid: f5 (for VC).ro SheAtmOamLevelType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.10.1.6 |
sheShdslVccTpLoopTestThe type of loop test . For EndToEnd loop test loop location ID is FF..FF.ro SheAtmOamLoopTestType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.10.1.7 |
sheShdslVccTpLoopTestResultPossible values: segSuccess(0), segFailure(1), endToEndSuccess(2), endToEndFailure(3), aborted(4), progress(5), notAvailable(65535)ro SheAtmOamLoopTestResultType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.10.1.8 |
sheShdslVccTpLoopLocIdTest cell loopback location. It is an identifier known by the crafts person identifying a ATM node in the ATM network. For EndToEnd loop test the default value is valid.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.10.1.9 |
sheShdslVccTpAlarmSeverityIndexIndex to the AlarmSeverityProfileTable. Defines the actual AlarmSeverities for all alarms per VccTp.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.10.1.10 |
sheShdslVccTpControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.11 |
sheShdslVccTpControlRequestmodifyShdslVccTp: sheShdslVccTpControlIndex sheShdslVccTpControlVpi sheShdslVccTpControlVci sheShdslVccTpControlAlarmSeverityIndex modifyShdslVccTpLoopTest: sheShdslVccTpControlIndex sheShdslVccTpControlLoopTest createShdslVccTp: sheShdslVccTpControlSubLayerIndex sheShdslVccTpControlVpi sheShdslVccTpControlVci deleteShdslVccTp: sheShdslVccTpControlIndexrw SheShdslControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.11.1 |
sheShdslVccTpControlIndexIndex of the Table-entry to be configured.rw Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.11.2 |
sheShdslVccTpControlStatusThe status of a user command.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.11.3 |
sheShdslVccTpControlTimerThe maximum wait time for the manager for a long running user command.ro Gauge32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.11.4 |
sheShdslVccTpControlReqResultThe result of the last user command.ro SheShdslControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.11.5 |
sheShdslVccTpControlTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.11.6 |
sheShdslVccTpControlSubLayerIndexDescription.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.11.7 |
sheShdslVccTpControlVpiVpirw Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.11.9 |
sheShdslVccTpControlVciVcirw Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.11.10 |
sheShdslVccTpControlLoopTestActual LoopTest-Value. Only None or endToEnd will be accepted.rw SheAtmOamLoopTestType .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.11.11 |
sheShdslVccTpControlAlarmSeverityIndexIndex of the used AlarmSeverityProfile.rw Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.11.12 |
sheShdslVccTpNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.12 |
sheShdslVccTpModifiedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.12.2 |
sheShdslVccRDIAlarmRDI detected. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.12.4 |
sheShdslVccAISAlarmAIS detected. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.12.5 |
sheShdslVccTpConfigurationFailedNotification in case of failed VccTp-Configuration. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.12.6 |
sheShdslVccTpCreatedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.12.7 |
sheShdslVccTpDeletedConfiguration notification. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.12.8 |
sheShdslConformance OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.100 |
sheShdslCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.100.1 |
sheShdslComplianceDescription. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.100.1.1 |
sheShdslGroups OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.100.2 |
sheShdslGroupDescription. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.100.2.1 |
sheShdslControlGroupDescription. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.100.2.2 |
sheShdslNotificationGroupDescription. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.100.2.3 |
sheShdslObsoleteGroupDescription.obsolete Unknown .1.3.6.1.4.1.231.7.1.2.2.1.12.1.2.100.2.4 |