SHE-MELT-MIB
Definition of MELT (metallic line testing) feature control commands and results. New supported with R3.7M.
Main OID:
sheMelt.1.3.6.1.4.1.231.7.1.2.2.1.24
107
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
107 total| Object Name |
|---|
sheMeltDefinition of MELT (metallic line testing) feature control commands and results. New supported with R3.7M. MODULE-IDENTITY .1.3.6.1.4.1.231.7.1.2.2.1.24 |
sheMeltTestRequestObjects OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.24.1 |
sheMeltTestParameter OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.24.1.1 |
sheMeltTestParameterFreq1This parameter contains the used frequency 1 for MELT impedance/admittance test.ro SheMeltTestFrequencyType UNITS "Hz" .1.3.6.1.4.1.231.7.1.2.2.1.24.1.1.1 |
sheMeltTestRequestStateTableEach entry in this table contains the testing status of each IfIndex. Only indeces of MELT feature supporting interfaces are listed in this table! SEQUENCE OF SheMeltTestRequestStateEntry .1.3.6.1.4.1.231.7.1.2.2.1.24.1.2 |
sheMeltTestRequestStateEntryAn entry in sheMeltTestRequestIfTable. SheMeltTestRequestStateEntry .1.3.6.1.4.1.231.7.1.2.2.1.24.1.2.1 |
sheMeltTestRequestIfStateThe MELT status of this interface. Only one port of one IU could be under test at time. Ports on different IU's could be under test at the same time. Check the corresponding sheMeltTestRequestIuState for this precondition. NOTE: Wetting current injection will be autonomously interrupted, if MELT or testTone insertion is started (WC configuration himself via sheXdslMib or sheShdslMib) for this interface as long as the test is running. Forgetting to stop test tone insertion will inhibit wetting current!ro SheMeltTestRequestIfStateType .1.3.6.1.4.1.231.7.1.2.2.1.24.1.2.1.1 |
sheMeltTestRequestIuStateThe MELT status of IU where this interface is located on. Every port must know whether this IU is under melt test already or not, in order to decide if the melt test request on this port can be accepted. Only one port of one IU could be under test at time. Ports on different IU's could be under test at the same time.ro SheMeltTestRequestIuStateType .1.3.6.1.4.1.231.7.1.2.2.1.24.1.2.1.2 |
sheMeltTestRequestTestToneIndexThis parameter points on a valid entry of sheMeltTestToneTable. These configuration is needed for test tone insertion on this line. One default profile with index 1 will always exist and is assigned per default to each line!ro SheMeltTestToneIndexType .1.3.6.1.4.1.231.7.1.2.2.1.24.1.2.1.3 |
sheMeltTestRequestStateControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.24.1.3 |
sheMeltTestRequestControlReqsetMeltTestParameters (1): sheMeltTestRequestControlParameterFreq1 startMeltTest (2): sheMeltTestRequestControlIndex stopMeltTest (3): sheMeltTestRequestControlIndex activateTestTone (4): sheMeltTestRequestControlIndex deactivateTestTone (5): sheMeltTestRequestControlIndex setMeltTestRequestTestToneIndex (8): sheMeltTestRequestControlIndex sheMeltTestRequestControlTestToneIndexrw SheMeltControlReqType .1.3.6.1.4.1.231.7.1.2.2.1.24.1.3.1 |
sheMeltTestRequestControlIndexThe interface index of the DSL central PPTP which should be configured.rw InterfaceIndex (IF-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.24.1.3.2 |
sheMeltTestRequestControlStatusThe status of a control request.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.24.1.3.3 |
sheMeltTestRequestControlTimerThe maximum wait time for the manager for a long running user command.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.24.1.3.4 |
sheMeltTestRequestControlReqResultThe result of the last user command.ro SheMeltControlReqResultType .1.3.6.1.4.1.231.7.1.2.2.1.24.1.3.5 |
sheMeltTestRequestControlReqTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.24.1.3.6 |
sheMeltTestRequestControlTestToneIndexlook at tablerw SheMeltTestToneIndexType .1.3.6.1.4.1.231.7.1.2.2.1.24.1.3.7 |
sheMeltTestRequestControlParameterFreq1Look at basic parameter group.rw SheMeltTestFrequencyType UNITS "Hz" .1.3.6.1.4.1.231.7.1.2.2.1.24.1.3.8 |
sheMeltTestToneObjects OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.24.2 |
sheMeltTestToneTableEach entry in this table contains a set of parameters for test tone generation. These entries could be assigned to each interface. One default entry exist which could NOT be modified or deleted! SEQUENCE OF SheMeltTestToneEntry .1.3.6.1.4.1.231.7.1.2.2.1.24.2.1 |
sheMeltTestToneEntryAn entry in sheMeltTestToneTable. SheMeltTestToneEntry .1.3.6.1.4.1.231.7.1.2.2.1.24.2.1.1 |
sheMeltTestToneIndexThis parameter is index of sheMeltTestToneTable. This configuration is needed for test tone insertion on the line. One default profile with index 1 will always exist and is assigned per default to each line!ro SheMeltTestToneIndexType .1.3.6.1.4.1.231.7.1.2.2.1.24.2.1.1.1 |
sheMeltTestToneFreq1The test tone frequency 1 of test tone set.ro SheMeltTestToneFrequencyType UNITS "Hz" .1.3.6.1.4.1.231.7.1.2.2.1.24.2.1.1.2 |
sheMeltTestToneFreq2The test tone frequency 2 of test tone set.ro SheMeltTestToneFrequencyType UNITS "Hz" .1.3.6.1.4.1.231.7.1.2.2.1.24.2.1.1.3 |
sheMeltTestToneLevelThe test tone level of test tone set.ro SheMeltTestSignalLevelType UNITS "dBm" .1.3.6.1.4.1.231.7.1.2.2.1.24.2.1.1.4 |
sheMeltTestToneControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.24.2.2 |
sheMeltTestToneControlReqcreateMeltTestToneEntry (10): (index will autonomously generated by NE) sheMeltTestToneControlFreq1 sheMeltTestToneControlFreq2 sheMeltTestToneControlLevel modifyMeltTestToneEntry (11): sheMeltTestToneControlIndex sheMeltTestToneControlFreq1 sheMeltTestToneControlFreq2 sheMeltTestToneControlLevel deleteMeltTestToneEntry (12): sheMeltTestToneControlIndexrw SheMeltControlReqType .1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.1 |
sheMeltTestToneControlIndexThe table index of the TestToneTable which should be configured. Default tone-set 1 could not be modified or deleted!rw SheMeltTestToneIndexType .1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.2 |
sheMeltTestToneControlStatusThe status of a control request.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.3 |
sheMeltTestToneControlTimerThe maximum wait time for the manager for a long running user command.ro Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.4 |
sheMeltTestToneControlReqResultThe result of the last user command.ro SheMeltControlReqResultType .1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.5 |
sheMeltTestToneControlReqTimeStampThe time stamp of the last command (end of command).ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.6 |
sheMeltTestToneControlFreq1look at tablerw SheMeltTestToneFrequencyType UNITS "Hz" .1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.7 |
sheMeltTestToneControlFreq2look at tablerw SheMeltTestToneFrequencyType UNITS "Hz" .1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.8 |
sheMeltTestToneControlLevellook at tablerw SheMeltTestSignalLevelType UNITS "dBm" .1.3.6.1.4.1.231.7.1.2.2.1.24.2.2.9 |
sheMeltTestResultObjects OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.24.3 |
sheMeltTestResultTableEach entry in this table contains the testing results of each IfIndex. Only indeces of MELT feature supporting interfaces are listed in this table! SEQUENCE OF SheMeltTestResultEntry .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1 |
sheMeltTestResultEntryAn entry in sheMeltTestResultTable. SheMeltTestResultEntry .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1 |
sheMeltTestResultStateThe MELT result status of this interface.ro SheMeltTestResultStateType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.1 |
sheMeltTestResultTimeStampTimestamp of last executed MELT.ro Unsigned32 UNITS "sec" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.2 |
sheMeltTestResultCapacityABThe MELT result for capacity a-wire - b-wire (ring - tip).ro SheMeltTestResultCapacityType UNITS "nF" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.3 |
sheMeltTestResultCapacityABValidThe valid information for capacitytest a-wire - b-wire, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.4 |
sheMeltTestResultCapacityAEThe MELT result for capacity a-wire - E (ring - earth).ro SheMeltTestResultCapacityType UNITS "nF" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.5 |
sheMeltTestResultCapacityAEValidThe valid information for capacitytest a-wire - earth, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.6 |
sheMeltTestResultCapacityBEThe MELT result for capacity b-wire - E (tip - earth).ro SheMeltTestResultCapacityType UNITS "nF" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.7 |
sheMeltTestResultCapacityBEValidThe valid information for capacitytest b-wire - earth, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.8 |
sheMeltTestResultResistanceABThe MELT result for resistance a-wire - b-wire (ring - tip). Note: The NMS should be able to show the values also in kOhms or MOhms for better readability.ro SheMeltTestResultResistanceType UNITS "Ohms" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.9 |
sheMeltTestResultResistanceABValidThe valid information for resistancetest a-wire - b-wire, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.10 |
sheMeltTestResultResistanceBAThe MELT result for resistance b-wire - a-wire (tip - ring). Note: The NMS should be able to show the values also in kOhms or MOhms for better readability.ro SheMeltTestResultResistanceType UNITS "Ohms" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.11 |
sheMeltTestResultResistanceBAValidThe valid information for resistancetest b-wire - a-wire, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.12 |
sheMeltTestResultResistanceAEThe MELT result for resistance a-wire - E (ring - earth). Note: The NMS should be able to show the values also in kOhms or MOhms for better readability.ro SheMeltTestResultResistanceType UNITS "Ohms" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.13 |
sheMeltTestResultResistanceAEValidThe valid information for resistancetest a-wire - earth, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.14 |
sheMeltTestResultResistanceBEThe MELT result for resistance b-wire - E (tip - earth). Note: The NMS should be able to show the values also in kOhms or MOhms for better readability.ro SheMeltTestResultResistanceType UNITS "Ohms" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.15 |
sheMeltTestResultResistanceBEValidThe valid information for resistancetest b-wire - earth, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.16 |
sheMeltTestResultForeignVoltageDcABThe MELT result for foreign voltage DC a-wire - b-wire (ring - tip).ro SheMeltTestResultDCVoltageType UNITS "100 mV" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.17 |
sheMeltTestResultForeignVoltageDcABValidThe valid information for foreignDcVoltagetest a-wire - b-wire, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.18 |
sheMeltTestResultForeignVoltageDcAEThe MELT result for foreign voltage DC a-wire - E (ring - earth).ro SheMeltTestResultDCVoltageType UNITS "100 mV" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.19 |
sheMeltTestResultForeignVoltageDcAEValidThe valid information for foreignDcVoltagetest a-wire - earth, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.20 |
sheMeltTestResultForeignVoltageDcBEThe MELT result for foreign voltage DC b-wire - E (tip - earth).ro SheMeltTestResultDCVoltageType UNITS "100 mV" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.21 |
sheMeltTestResultForeignVoltageDcBEValidThe valid information for foreignDcVoltagetest b-wire - earth, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.22 |
sheMeltTestResultForeignVoltageAcABThe MELT result for foreign voltage AC a-wire - b-wire (ring - tip).ro SheMeltTestResultACVoltageType UNITS "100 mV" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.23 |
sheMeltTestResultForeignVoltageAcABValidThe valid information for foreignAcVoltage test a-wire - b-wire, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.24 |
sheMeltTestResultForeignVoltageAcAEThe MELT result for foreign voltage AC a-wire - E (ring - earth).ro SheMeltTestResultACVoltageType UNITS "100 mV" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.25 |
sheMeltTestResultForeignVoltageAcAEValidThe valid information for foreignAcVoltagetest a-wire - earth, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.26 |
sheMeltTestResultForeignVoltageAcBEThe MELT result for foreign voltage AC b-wire - E (tip - earth).ro SheMeltTestResultACVoltageType UNITS "100 mV" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.27 |
sheMeltTestResultForeignVoltageAcBEValidThe valid information for foreignAcVoltagetest b-wire - earth, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.28 |
sheMeltTestResultForeignVoltageAcFrequencyABThe MELT result for foreign voltage AC frequency a-wire - b-wire (ring - tip).ro SheMeltTestResultACVoltageFrequencyType UNITS "Hz" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.29 |
sheMeltTestResultForeignVoltageAcFrequencyABValidThe valid information for foreignAcVoltageFrequency test a-wire - b-wire, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.30 |
sheMeltTestResultForeignVoltageAcFrequencyAEThe MELT result for foreign voltage AC frequency a-wire - earth (ring - earth).ro SheMeltTestResultACVoltageFrequencyType UNITS "Hz" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.31 |
sheMeltTestResultForeignVoltageAcFrequencyAEValidThe valid information for foreignAcVoltageFrequency test a-wire - earth, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.32 |
sheMeltTestResultForeignVoltageAcFrequencyBEThe MELT result for foreign voltage AC frequency b-wire - earth (tip - earth).ro SheMeltTestResultACVoltageFrequencyType UNITS "Hz" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.33 |
sheMeltTestResultForeignVoltageAcFrequencyBEValidThe valid information for foreignAcVoltageFrequency test b-wire - earth, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.34 |
sheMeltTestResultForeignCurrentABThe MELT result for foreign current test a-wire - b-wire (ring - tip).ro SheMeltTestResultForeignCurrentType UNITS "uA" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.35 |
sheMeltTestResultForeignCurrentABValidThe valid information for foreignCurrenttest a-wire - b-wire, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.36 |
sheMeltTestResultForeignCurrentAEThe MELT result for foreign current test a-wire - E (ring - earth).ro SheMeltTestResultForeignCurrentType UNITS "uA" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.37 |
sheMeltTestResultForeignCurrentAEValidThe valid information for foreignCurrenttest a-wire - earth, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.38 |
sheMeltTestResultForeignCurrentBEThe MELT result for foreign current test b-wire - E (tip - earth).ro SheMeltTestResultForeignCurrentType UNITS "uA" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.39 |
sheMeltTestResultForeignCurrentBEValidThe valid information for foreignCurrenttest b-wire - earth, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.40 |
sheMeltTestResultConductanceABThe MELT result for conductance test a-wire - b-wire (ring - tip).ro SheMeltTestResultConductanceType UNITS "100 nS" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.41 |
sheMeltTestResultConductanceABValidThe valid information for conductancetest a-wire - b-wire, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.42 |
sheMeltTestResultConductanceAEThe MELT result for conductance test a-wire - earth (ring - earth).ro SheMeltTestResultConductanceType UNITS "100 nS" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.43 |
sheMeltTestResultConductanceAEValidThe valid information for conductancetest a-wire - earth, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.44 |
sheMeltTestResultConductanceBEThe MELT result for conductance test b-wire - earth (tip - earth).ro SheMeltTestResultConductanceType UNITS "100 nS" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.45 |
sheMeltTestResultConductanceBEValidThe valid information for conductancetest b-wire - earth, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.46 |
sheMeltTestResultSusceptanceABThe MELT result for susceptance test a-wire - b-wire (ring - tip).ro SheMeltTestResultConductanceType UNITS "100 nS" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.47 |
sheMeltTestResultSusceptanceABValidThe valid information for susceptancetest a-wire - b-wire, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.48 |
sheMeltTestResultSusceptanceAEThe MELT result for susceptance test a-wire - earth (ring - earth).ro SheMeltTestResultConductanceType UNITS "100 nS" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.49 |
sheMeltTestResultSusceptanceAEValidThe valid information for susceptancetest a-wire - earth, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.50 |
sheMeltTestResultSusceptanceBEThe MELT result for susceptance test b-wire - earth (tip - earth).ro SheMeltTestResultConductanceType UNITS "100 nS" .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.51 |
sheMeltTestResultSusceptanceBEValidThe valid information for susceptancetest b-wire - earth, if sheMeltTestResultState = testSucceeded.ro SheMeltTestResultValidType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.52 |
sheMeltTestResultCheckPPAThe MELT result for PPA test.ro SheMeltTestResultCheckPpaType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.53 |
sheMeltTestResultCheckSplitterThe MELT result for Splitter test.ro SheMeltTestResultCheckType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.54 |
sheMeltTestResultCheckIADThe MELT result for IAD test.ro SheMeltTestResultCheckType .1.3.6.1.4.1.231.7.1.2.2.1.24.3.1.1.55 |
sheMeltNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.24.10 |
sheMeltTestRequestParametersModifiedThe MELT testparameters are modified. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.24.10.1 |
sheMeltTestRequestStateModifiedThe MELT state of an interface was modified by command or by NE. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.24.10.2 |
sheMeltTestRequestIfTestToneIndexModifiedThe used test tone set of an interface (assignment interface - test tone index) was modified. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.24.10.3 |
sheMeltTestToneEntryCreatedConfiguration trap for new created MELT testTone set. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.24.10.4 |
sheMeltTestToneEntryModifiedConfiguration trap for modified MELT testTone set. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.24.10.5 |
sheMeltTestToneEntryDeletedConfiguration trap for delete a MELT testTone set. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.24.10.6 |
sheMeltConformance OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.24.100 |
sheMeltCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.24.100.1 |
sheMeltMibComplianceDescription. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.24.100.1.1 |
sheMeltGroups OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.24.100.2 |
sheMeltGroup Unknown .1.3.6.1.4.1.231.7.1.2.2.1.24.100.2.1 |
sheMeltControlGroupDescription. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.24.100.2.2 |
sheMeltNotificationGroup Unknown .1.3.6.1.4.1.231.7.1.2.2.1.24.100.2.3 |