SHE-L2CP-MIB
She L2CP interface description.
Main OID:
sheL2cpMib.1.3.6.1.4.1.231.7.1.2.2.1.16
67
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
67 total| Object Name |
|---|
sheL2cpMibShe L2CP interface description. MODULE-IDENTITY .1.3.6.1.4.1.231.7.1.2.2.1.16 |
sheL2cpObjects OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.16.1 |
sheL2cpIfTableThe L2CP interface table. SEQUENCE OF SheL2cpIfEntry .1.3.6.1.4.1.231.7.1.2.2.1.16.1.2 |
sheL2cpIfEntryAn entry of the L2CP interface table (sheL2cpIfTable) SheL2cpIfEntry .1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1 |
sheL2cpIfIndexThe index of an L2CP protocol instance in the sheL2cpIfTable.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.1 |
sheL2cpOperStateThe operational state of the L2CP interface.ro SheL2cpOperStateType .1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.2 |
sheL2cpAdjacencyStateThe state of the adjacency protocol.ro SheL2cpAdjacencyStateType .1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.3 |
sheL2cpTimer1This timer defines the TIMER field is used to inform the receiver of the timer value used in the adjacency protocol of the sender. The timer specifies the nominal time between periodic adjacency protocol messages. It is a constant for the duration of a session.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.4 |
sheL2cpTimer2This value defines the minimum time between two port state messages of the same port. It is used to limit the port messages in case of toggeling ports. The timer base is 1s. 0 means: all port state changes are reported.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.5 |
sheL2cpTimer3This timeout is used to handle L2CP message flooding after Controller recovery. The timer is started when the link to the controller was established, The first port state message is sent when this timer expires.ro INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.6 |
sheL2cpControllerIpAddressThe IP address of the remote L2cp controller which should be contacted by this interface.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.7 |
sheL2cpAccessNodeIdentifierThe name of the access node. The DSLAM identifies itself with the controller by means of this name.ro OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.8 |
sheL2cpPartitionIdThe ID of the partition managed via this L2CP protocol instance. (see RFC 3292). The value 257 is not used here.ro SheL2cpPartitionIdType .1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.10 |
sheL2cpAlarmSeverityIndexThe currently used alarm severity profile index for this l2cp interface.ro SheAlarmSevProfileIndex (SHE-ALARMING-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.16.1.2.1.11 |
sheL2cpPortPartitionTableThe L2CP port table. The index in this table is the ifIndex. But only such interfaces are listed in this table which are of type xDSL. SEQUENCE OF SheL2cpPortPartitionEntry .1.3.6.1.4.1.231.7.1.2.2.1.16.1.3 |
sheL2cpPortPartitionEntryAn entry in the L2CP port partition table (sheL2cpPortPartitionTable). SheL2cpPortPartitionEntry .1.3.6.1.4.1.231.7.1.2.2.1.16.1.3.1 |
sheL2cpPortPartitionIdThe ID of the partition managed the port is assigned to. 0...255: These are really partition IDs. The port is managed by such L2CP interface instances which have the same partition ID. 256: no partition. The port belongs to no partition. It is managed by such L2CP interface instances wich are assigned to 'no partition'. 257: invalid partition The port is not managed by any L2CP instance.ro SheL2cpPartitionIdType .1.3.6.1.4.1.231.7.1.2.2.1.16.1.3.1.2 |
sheL2cpControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.16.1.4 |
sheL2cpControlRequestThe L2CP commands: createL2cpIf: Create a new L2CP interface instance: Parameter: sheL2cpControlTimer1, sheL2cpControlTimer2, sheL2cpControlTimer3, sheL2cpControlControllerIpAddress, sheL2cpControlPartitionId, sheL2cpControlAccessNodeIdentifier sheL2cpControlAlarmSeverityIndex deleteL2cpIf: Delete a L2CP interface instance. Parameter: sheL2cpControlIndex modifyL2cpIf: Change the parameter of an L2CP interface instance. Parameter: sheL2cpControlL2cpIndex, sheL2cpControlTimer1, sheL2cpControlTimer2, sheL2cpControlTimer3, sheL2cpControlControllerIpAddress, sheL2cpControlPartitionId, sheL2cpControlAccessNodeIdentifier sheL2cpControlAlarmSeverityIndex assignPortToPartition: A port is assigned to a partition. Parameter: sheL2cpControlIndex, sheL2cpControlPartitionIdrw SheL2cpControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.1 |
sheL2cpControlIndexThe index of a port in the port partition table (vshL2cpPortPartitionTable) if the PartionId should be set or the index of a valid L2cpIf in the sheL2cpIfTable for modify or delete of these interface.rw Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.2 |
sheL2cpControlStatusThe status of a user command.ro SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.3 |
sheL2cpControlReqResultThe result of the last ControlRequestro SheL2cpControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.4 |
sheL2cpControlTimerThe maximum wait time for the manager for a long running user command.ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.5 |
sheL2cpControlTimeStampThe time stamp of the last command (end of command).ro Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.6 |
sheL2cpControlTimer1This timer defines the timer value used by the adjacency protocol. It defines the time between perdiodic adjacency protocol messages. The time base are 100ms. (see RFC 3292)rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.7 |
sheL2cpControlTimer2This value defines the minimum time between two port state messages of the same port. It is used to limit the port messages in case of toggeling ports. The timer base is 1s. 0 means: all port state changes are reported.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.8 |
sheL2cpControlTimer3This value defines the time before all port states are reported to controller after an L2CP connection was established. This timer can be used to avoid a message flooding of the controller. The timer base is 1s.rw INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.9 |
sheL2cpControlControllerIpAddressThe IP address of the controller.rw OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.10 |
sheL2cpControlAccessNodeIdentifierThe name of the access node. The DSLAM identifies itself with the controller by means of this name.rw OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.11 |
sheL2cpControlPartitionIdThe ID of the partition managed by an L2CP protocol instance (see RFC 3292). The partition to which a port is assigned.rw SheL2cpPartitionIdType .1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.12 |
sheL2cpControlAlarmSeverityIndexlook at table.rw SheAlarmSevProfileIndex (SHE-ALARMING-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.16.1.4.13 |
sheL2cpNotification OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.16.1.5 |
sheL2cpAlarmEvents OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.1 |
sheL2cpLinkDownDescription. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.1.1 |
sheL2cpConfigEvents OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.2 |
sheL2cpIfCreatedConfiguration trap. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.2.1 |
sheL2cpIfDeletedConfiguration trap. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.2.2 |
sheL2cpIfModifiedConfiguration trap. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.2.3 |
sheL2cpPartitionPortDataChangedConfiguration trap. NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.2.4 |
sheL2cpHostIfCreatedNote: This parameter is not longer valid starting with release SHE R2.6 The IP interface configuration was moved to sheSystemIpHostTable.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.2.5 |
sheL2cpHostIfModifiedNote: This parameter is not longer valid starting with release SHE R2.6. The IP interface configuration was moved to sheSystemIpHostTable.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.2.6 |
sheL2cpHostIfDeletedNote: This parameter is not longer valid starting with release SHE R2.6 The IP interface configuration was moved to sheSystemIpHostTable.obsolete NOTIFICATION-TYPE .1.3.6.1.4.1.231.7.1.2.2.1.16.1.5.2.7 |
sheL2cpHostIfTableNote: This parameter is not longer valid starting with release SHE R2.6. The IP interface configuration was moved to sheSystemIpHostTable.obsolete SEQUENCE OF SheL2cpHostIfEntry .1.3.6.1.4.1.231.7.1.2.2.1.16.1.6 |
sheL2cpHostIfEntryThe index of an L2CP host interface instance in this table. Note: This parameter is not longer valid starting with release SHE R2.6. The IP interface configuration was moved to sheSystemIpHostTable.obsolete SheL2cpHostIfEntry .1.3.6.1.4.1.231.7.1.2.2.1.16.1.6.1 |
sheL2cpHostIfIndexUnique key for that table.roobsolete INTEGER .1.3.6.1.4.1.231.7.1.2.2.1.16.1.6.1.1 |
sheL2cpHostIfVlanIdThe host vlan for the local L2cp interface which should be used as tag to contact the remote L2cp controller.roobsolete Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.16.1.6.1.2 |
sheL2cpHostIfIpAddressThe IP address of the local L2cp interface which should be used by the NE.roobsolete OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.16.1.6.1.3 |
sheL2cpHostIfNetmaskThe l2cp host interface Netmask.roobsolete OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.16.1.6.1.5 |
sheL2cpHostIfControl OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.16.1.7 |
sheL2cpHostIfControlRequestThe L2CP commands: Note: This parameter is not longer valid starting with release SHE R2.6. The IP interface configuration was moved to sheSystemIpHostTable. createL2cpHostIf: Create a new L2CP host interface instance: Parameter: sheL2cpHostIfControlVlanId sheL2cpHostIfControlIpAddress sheL2cpHostIfControlNetmask deleteL2cpHostIf: Delete a L2CP host interface instance. Parameter: sheL2cpHostIfControlIndex modifyL2cpHostIf: Change the parameter of an L2CP host interface instance. Parameter: sheL2cpHostIfControlIndex sheL2cpHostIfControlIpAddress sheL2cpHostIfControlNetmaskrwobsolete SheL2cpControlRequestType .1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.1 |
sheL2cpHostIfControlIndexThe index of a valid L2cpHostIf from sheL2cpHostIfTable for modifies or delete.rwobsolete Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.2 |
sheL2cpHostIfControlStatusThe status of a user command.roobsolete SheControlStatusType (SHE-TC-MIB) .1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.3 |
sheL2cpHostIfControlReqResultThe result of the last ControlRequestroobsolete SheL2cpControlRequestResultType .1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.4 |
sheL2cpHostIfControlTimerThe maximum wait time for the manager for a long running user command.roobsolete Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.5 |
sheL2cpHostIfControlTimeStampThe time stamp of the last command (end of command).roobsolete Integer32 .1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.6 |
sheL2cpHostIfControlVlanIdThe host vlan for the local L2cp interface which should be used as tag to contact the remote L2cp controller. This value could only be used for create command. A modification is not allowed!rwobsolete Unsigned32 .1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.7 |
sheL2cpHostIfControlIpAddressThe IP address of the local L2cp host interface.rwobsolete OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.8 |
sheL2cpHostIfControlNetmaskThe l2cp host interface Netmask.rwobsolete OCTET STRING .1.3.6.1.4.1.231.7.1.2.2.1.16.1.7.10 |
sheL2cpConformance OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.16.1.8 |
sheL2cpGroups OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.16.1.8.1 |
sheL2cpGroupA collection of objects providing information about a VDSL Line. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.16.1.8.1.1 |
sheL2cpControlGroupDescription. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.16.1.8.1.2 |
sheL2cpNotificationGroupThis group supports notifications of significant conditions associated with VDSL Lines. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.16.1.8.1.3 |
sheL2cpObsoleteGroupDescription.obsolete Unknown .1.3.6.1.4.1.231.7.1.2.2.1.16.1.8.1.4 |
sheL2cpObsoleteNotificationGroupDescription.obsolete Unknown .1.3.6.1.4.1.231.7.1.2.2.1.16.1.8.1.5 |
sheL2cpCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.231.7.1.2.2.1.16.1.8.2 |
sheL2cpMibComplianceThe compliance statement for SNMP entities which manage VDSL interfaces in SHE. Unknown .1.3.6.1.4.1.231.7.1.2.2.1.16.1.8.2.1 |