S5-TOK-TOPOLOGY-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for S5-TOK-TOPOLOGY-MIB.
64
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
64 total| Object Name |
|---|
RFC1155-SMIA table with topology status and control
for each token ring interface on the NMM. The
number of entries is determined by the number
of token ring interfaces on the NMM. SEQUENCE OF S5TrTopIfEntry .1.3.6.1.4.1.45.1.6.10.1 |
s5TrTopNmmTableA table of topology information for each
Network Management Module (NMM) with a Token
Ring interface on the same 'flat network'
as the reporting NMM. The number of entries
is determined by the number of detected
(and active) NMMs. Entries in the table are
created by reception of a topology message
with information about a 'new' NMM. An entry
is removed from the table when an NMM is
not present in the topology message from
a ring, or when no topology messages are
received from a ring in the required time
interval. SEQUENCE OF S5TrTopNmmEntry .1.3.6.1.4.1.45.1.6.10.2 |
s5TrTopNmmEntryA row in the table of topology information
about Network Management Modules (NMMs) with
a Token Ring interface on the same 'flat
network' as the reporting NMM. Entries in the
table can not be created or deleted via SNMP. S5TrTopNmmEntry .1.3.6.1.4.1.45.1.6.10.2.1 |
s5TrTopNmmIfIpAddrThe IP address of the interface on which
the topology message was received.ro IpAddress .1.3.6.1.4.1.45.1.6.10.2.1.1 |
s5TrTopNmmIpAddrThe IP address of an NMM contained in
a topology message.ro IpAddress .1.3.6.1.4.1.45.1.6.10.2.1.2 |
s5TrTopNmmRingNumThe ring number on which an NMM from a
topology message is located.ro INTEGER .1.3.6.1.4.1.45.1.6.10.2.1.3 |
s5TrTopNmmRingMasterThe classification of an NMM from
a topology message. The values are:
normal(1)...not a master NMM
master(2)...a master NMMro Enumeration .1.3.6.1.4.1.45.1.6.10.2.1.4 |
s5TrTopNmmRingSpeedThe speed of the ring (in units of Mbits)
on which an NMM from a topology message is
located. The expected values are:
4....4 Mbps
16...16 Mbpsro INTEGER .1.3.6.1.4.1.45.1.6.10.2.1.5 |
s5TrTopNmmBridgeGroupIdentifierThe forwarding domain identification
VLAN ID, if applicable, of the port on
which the SONMP message for this entry
was heard. The value shall be zero if
the entry is local, or if the port number
cannot be resolved.ro INTEGER .1.3.6.1.4.1.45.1.6.10.2.1.6 |
s5TrTopNmmSlotNumThe slot number of the port on which the SONMP
message for this entry was heard. The value shall
be zero if the port number cannot be resolved.ro INTEGER .1.3.6.1.4.1.45.1.6.10.2.1.7 |
s5TrTopNmmPortNumThe port number of the port on which the SONMP
message for this entry was heard. The value shall
be zero if the port number cannot be resolved.ro INTEGER .1.3.6.1.4.1.45.1.6.10.2.1.8 |
s5TrTopBdgTableA table that lists each known bridge
with a Token Ring interface on the same
'flat net' as the reporting NMM. The
number of entries is determined by
the number of detected (and active)
bridges. Entries are added by reception of
a topology message from a bridge or reception
of a topology message from an master NMM that
was forwarded by a source routing bridge.
An entry is removed from the table when
no topology messaged are received from
bridge in the required time interval. SEQUENCE OF S5TrTopBdgEntry .1.3.6.1.4.1.45.1.6.10.3 |
s5TrTopBdgEntryA row in the table of known bridges
with a Token Ring interface on the same
'flat net' as the reporting NMM. Entries
in the table can not be created or deleted
via SNMP. S5TrTopBdgEntry .1.3.6.1.4.1.45.1.6.10.3.1 |
s5TrTopBdgIfIpAddrThe IP address of the interface on which
the topology message was received.ro IpAddress .1.3.6.1.4.1.45.1.6.10.3.1.1 |
s5TrTopBdgIndxThe index of the entry in the table
for the interface.ro INTEGER .1.3.6.1.4.1.45.1.6.10.3.1.2 |
s5TrTopBdgNumThe IEEE 802.5 'bridge number' for
the bridge.ro INTEGER .1.3.6.1.4.1.45.1.6.10.3.1.3 |
s5TrTopBdgOwnRingNumThe ring number for the reporting NMM.
NOTE: this will be the same value for all
table entries for each interface.ro INTEGER .1.3.6.1.4.1.45.1.6.10.3.1.4 |
s5TrTopBdgAdjRingNumThe ring number of the adjacent ring
that is joined by the bridge. The value
is zero if this entry in the table was
created due to the receipt of a topology
message from another NMM on a different
ring and the bridge connecting the rings
was a transparent only bridge and it does
not generate topology messages.ro INTEGER .1.3.6.1.4.1.45.1.6.10.3.1.5 |
s5TrTopBdgAdjMasterNmmIpAddrIf this entry was created (and/or validated)
by a topology message from a master NMM,
then the value is its IP address. If the
value of object s5TrTopBdgNum is non-zero,
then the master NMM is on an adjacent ring.
If the value of s5TrTopBdgNum is zero, then
the master NMM may be adjacent, or several
rings away, separated by one or more
transparent bridges.
The value for this object is 0.0.0.0 when the
bridge generates a topology message and
there is no master NMM on the adjacent ring
nor one connected to the adjacent ring through
one or more transparent bridges.ro IpAddress .1.3.6.1.4.1.45.1.6.10.3.1.6 |
s5TrTopBdgMacAddrThe MAC address of the bridge port sending
the topology message. The value is
00:00:00:00:00:00 if the bridge does not
transmit topology messages.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.45.1.6.10.3.1.7 |
s5TrTopBdgIpAddrIP address of the bridge sending the topology
message. The value is 0.0.0.0 if the bridge
does not transmit topology messages.ro IpAddress .1.3.6.1.4.1.45.1.6.10.3.1.8 |
s5TrTopBdgTypeThe kind of bridge this entry represents.
The values come from the topology messages
generated by the bridge. The values are:
other(1)...........bridge does not send topology
messages or is not a
defined type
t3522Syn2Port(2)...SynOptics 2 port bridge in
a modular concentrator
t2722Syn2Port(3)...SynOptics 2 port stand-alone
bridge
tCenTillionTrSwitch(4)...Centillion multi-port
TR switchro Enumeration .1.3.6.1.4.1.45.1.6.10.3.1.9 |
s5TrTopBdgSlotNumThe slot that the reporting NMM received the
topology message from the bridge. The value
zero is used to indicate that the bridge does
not transmit topology messages or the slot
from which the message was received can not be
determined.ro INTEGER .1.3.6.1.4.1.45.1.6.10.3.1.10 |
s5TrTopBdgPortNumThe port that the reporting NMM received the
topology message from the bridge. The value
zero is used to indicate that the bridge does
not transmit topology messages or the port
from which the message was received can not
be determined.ro INTEGER .1.3.6.1.4.1.45.1.6.10.3.1.11 |
s5TrTopBdgNumPortThe total number of ports installed on the
bridge. The value zero is used to indicate that
the bridge does not transmit topology messages.ro INTEGER .1.3.6.1.4.1.45.1.6.10.3.1.12 |
s5TrTopBdgHelloPortNumThe port on the bridge from which the topology
message was sent. The value zero is used to
indicate that the bridge does not transmit
topology messages.ro INTEGER .1.3.6.1.4.1.45.1.6.10.3.1.13 |
s5TrTopBdgHelloPortStatusThe status of the port on Bridge from which
the topology message was sent. The values are:
other(1).............bridge does not send topology
messages or port not in
defined status
tranAct(2)...........Transparent active
tranStnBy(3).........Transparent standby
srSrsOn(4)...........Source routing single route
spanning is on
srSrsOff(5)..........Source routing single route
spanning is off
srSrsOnTranAct(6)....Source routing single route
spanning is on, and
transparent active
srSrsOffTranAct(7)...Source routing single route
spanning is off, and
transparent active
srSrsOnStnBy(8)......Source routing single route
spanning is on, and
transparent standby
srSrsOffStnBy(9).....Source routing single route
spanning is off, and
transparent standbyro Enumeration .1.3.6.1.4.1.45.1.6.10.3.1.14 |
s5TrTopBdgMonPortStatusThe status of the 'monitor' port on Bridge from
which the topology message was sent.
The values are:
other(1)...............bridge does not send topology
messages or the status of
the monitor port is unknown
or the bridge does not have
a monitor port, or some other
condition.
phantomOff(2)..........phantom status is off
phantomOn(3)...........phantom status is on
phantomOffWrapped(4)...phantom off and port wrapped
phantomOnWrapped(5)....phantom on and port wrapped
wrongSpeedWrap(6)......port wrapped for wrong speedro Enumeration .1.3.6.1.4.1.45.1.6.10.3.1.15 |
s5TrTopBdgHelloTypeThe type of topology message received from the
bridge. The values are:
other..........bridge does not send any of the
recognizable topology message
types
synoptics(2)...bridge sends SynOptics' topology
messagero Enumeration .1.3.6.1.4.1.45.1.6.10.3.1.16 |
s5TrTopRingNmmTableA table listing all the Network Management
Modules (NMMs) with a Token Ring interface
on the same ring as the reporting NMM. The
number of entries is determined by the number
of detected (and active) NMMs. Entries are
created by reception of a topology message from
a 'new' NMM. An entry is removed from the table
when no topology messages are received from the
NMM in the required time interval. SEQUENCE OF S5TrTopRingNmmEntry .1.3.6.1.4.1.45.1.6.10.4 |
s5TrTopRingNmmEntryA row in the table of Network Management
Modules (NMMs) with a Token Ring interface
on the same ring as the reporting NMM.
Entries in the table can not be created
or deleted via SNMP. S5TrTopRingNmmEntry .1.3.6.1.4.1.45.1.6.10.4.1 |
s5TrTopRingNmmIfIpAddrThe IP address of the interface on which
the topology message was received.ro IpAddress .1.3.6.1.4.1.45.1.6.10.4.1.1 |
s5TrTopRingNmmIpAddrThe IP address of the NMM that sent
the topology message.ro IpAddress .1.3.6.1.4.1.45.1.6.10.4.1.2 |
s5TrTopRingNmmMacAddrThe MAC address of the NMM that sent
the topology message.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.45.1.6.10.4.1.3 |
s5TrTopRingNmmChassisTypeThe type of chassis containing the NMM
that sent the topology message.ro SnpxChassisType .1.3.6.1.4.1.45.1.6.10.4.1.4 |
s5TrTopRingNmmBkplTypeThe type of backplane in the chassis
containing the NMM that sent the topology
message.ro SnpxBackplaneType .1.3.6.1.4.1.45.1.6.10.4.1.5 |
s5TrTopRingNmmSlotNumThe slot containing the NMM that sent the
topology message.ro INTEGER .1.3.6.1.4.1.45.1.6.10.4.1.6 |
s5TrTopRingNmmUnaIpAddrThe IP address of the next upstream NMM
of the NMM that sent the topology message.ro IpAddress .1.3.6.1.4.1.45.1.6.10.4.1.7 |
s5TrTopNmmEosSizeThe current size of a 'row' in the table
s5TrTopNmmEosTable. This allows applications
to be able to break apart 'rows' in the table.ro INTEGER .1.3.6.1.4.1.45.1.6.10.5 |
s5TrTopNmmEosTableA table of encoded octet strings of
entries in table s5TrTopNmmTable.
The number of entries is determined by the
packing of 'rows' from s5TrTopNmmTable. SEQUENCE OF S5TrTopNmmEosEntry .1.3.6.1.4.1.45.1.6.10.6 |
s5TrTopNmmEosEntryA row in the table of encoded octet
strings for table s5TrTopNmmTable.
Instance returned in Response PDU:
On GETs: instance specified is the
instance returned.
On GET-NEXTs: instance returned is the
instance of the last record
contained in the octet string.
Entries in the table can not be created
or deleted via SNMP. S5TrTopNmmEosEntry .1.3.6.1.4.1.45.1.6.10.6.1 |
s5TrTopNmmEosAn encoded octet string. On reads it contains
an integral number of 'rows' from table
s5TrTopNmmTable. All 'rows' are the same size
which is defined by object s5TrTopNmmEosSize.ro OCTET STRING .1.3.6.1.4.1.45.1.6.10.6.1.1 |
s5TrTopBdgEosSizeThe current size of a 'row' in the table
s5TrTopBdgEosTable. This allows applications
to be able to break apart 'rows' in the table.ro INTEGER .1.3.6.1.4.1.45.1.6.10.7 |
s5TrTopBdgEosTableA table of encoded octet strings of
entries in table s5TrTopBdgTable.
The number of entries is determined by the
packing of 'rows' from s5TrTopBdgTable. SEQUENCE OF S5TrTopBdgEosEntry .1.3.6.1.4.1.45.1.6.10.8 |
s5TrTopBdgEosEntryA row in the table of encoded octet
strings for table s5TrTopBdgTable.
Instance returned in Response PDU:
On GETs: instance specified is the
instance returned.
On GET-NEXTs: instance returned is the
instance of the last record
contained in the octet string.
Entries in the table can not be created
or deleted via SNMP. S5TrTopBdgEosEntry .1.3.6.1.4.1.45.1.6.10.8.1 |
s5TrTopBdgEosAn encoded octet string. On reads it contains
an integral number of 'rows' from table
s5TrTopBdgEntry. All 'rows' are the same size
which is defined by object s5TrTopBdgEosSize.ro OCTET STRING .1.3.6.1.4.1.45.1.6.10.8.1.1 |
s5TrTopRingNmmEosSizeThe current size of a 'row' in the table
s5TrTopRingNmmEosTable. This allows applications
to be able to break apart 'rows' in the table.ro INTEGER .1.3.6.1.4.1.45.1.6.10.9 |
s5TrTopRingNmmEosTableA table of encoded octet strings of
entries in table s5TrTopRingNmmTable.
The number of entries is determined by the
packing of 'rows' from s5TrTopRingNmmTable. SEQUENCE OF S5TrTopRingNmmEosEntry .1.3.6.1.4.1.45.1.6.10.10 |
s5TrTopRingNmmEosEntryA row in the table of encoded octet
strings for table s5TrTopRingNmmTable.
Instance returned in Response PDU:
On GETs: instance specified is the
instance returned.
On GET-NEXTs: instance returned is the
instance of the last record
contained in the octet string.
Entries in the table can not be created
or deleted via SNMP. S5TrTopRingNmmEosEntry .1.3.6.1.4.1.45.1.6.10.10.1 |
s5TrTopRingNmmEosAn encoded octet string. On reads it contains
an integral number of 'rows' from table
s5TrTopRingNmmTable. All 'rows' are the same size
which is defined by object s5TrTopNmmEosSize.ro OCTET STRING .1.3.6.1.4.1.45.1.6.10.10.1.1 |
s5TrTopIfEntryA row in the table of topology status and
control for each token ring interface on the
NMM. Entries in the table can not be created
or deleted via SNMP. S5TrTopIfEntry .s5TrTopIfTable.1 |
s5TrTopIfIpAddrThe IP address of the interface.ro IpAddress .s5TrTopIfTable.1.1 |
s5TrTopIfNumThe value of ifIndex for the interface.ro INTEGER .s5TrTopIfTable.1.2 |
s5TrTopIfStatusIndicates if the interface is participating
in topology. The values are:
topOn(1)....topology is on
topOff(2)...topology is off
When the value is topOff(2) the status
of entries associated with the interface
is undefined. However, the agent should
make its best attempt when the value is
changed to topOff(2) to remove all
existing instances of topology MIB objects
for the interface. The agent must save
the setting of this object in nonvolatile
memory (i.e., save across reboots).rw Enumeration .s5TrTopIfTable.1.3 |
s5TrTopIfNmmLstChgThe value of sysUpTime when the last
addition or deletion of an NMM topology
table entry associated with the interface
was done. If none have been done since
cold/warm start of the agent, then the
value is zero.ro TimeTicks (SNMPv2-SMI) .s5TrTopIfTable.1.4 |
s5TrTopIfBdgLstChgThe value of sysUpTime when the last
addition or deletion of a bridge
topology table entry associated with the
interface was done. If none have been
done since cold/warm start of the
agent, then the value is zero.ro TimeTicks (SNMPv2-SMI) .s5TrTopIfTable.1.5 |
s5TrTopIfRingNmmLstChgThe value of sysUpTime when the last
addition or deletion of a Ring NMM
topology table entry associated with
the interface was done. If none have
been done since cold/warm start
of the agent, then the value is zero.ro TimeTicks (SNMPv2-SMI) .s5TrTopIfTable.1.6 |
s5TrTopIfNmmMaxNumThe maximum number of entries for the
interface in the NMM topology table.ro INTEGER .s5TrTopIfTable.1.7 |
s5TrTopIfNmmCurNumThe current number of entries for the
interface in the NMM topology table.ro INTEGER .s5TrTopIfTable.1.8 |
s5TrTopIfBdgMaxNumThe maximum number of entries for the
interface in the bridge topology table.ro INTEGER .s5TrTopIfTable.1.9 |
s5TrTopIfBdgCurNumThe current number of entries for the
interface in the bridge topology table.ro INTEGER .s5TrTopIfTable.1.10 |
s5TrTopIfRingNmmMaxNumThe maximum number of entries for the
interface in the Ring NMM topology table.ro INTEGER .s5TrTopIfTable.1.11 |
s5TrTopIfRingNmmCurNumThe current number of entries for the
interface in the Ring NMM topology table.ro INTEGER .s5TrTopIfTable.1.12 |
s5TrTopIfTopSpeedThe Token Ring topology message (SONMP frame)
transmit speed. The values that are read/write are:
topFast(2)...short interval between transmitting
topSlow(3)...long interval between transmitting
The value that is readonly is:
other(1)...speed unknown, or other value
In fast mode, the SONMP frame transmit interval
is 10 seconds for all SONMP frames except
for ring master which is 5 seconds.
In slow mode, the interval is 15 seconds for ring
master SONMP frames, 50 seconds for concentrator
profile SONMP frames, 60 seconds for master NMM
announcement SONMP frames, and 70 seconds for
adjacent SONMP frames.rw Enumeration .s5TrTopIfTable.1.13 |