RDN-CMTS-MIB
This is the enterprise MIB Module for Motorola's Cable Modem Termination Systems (CMTS).
Main OID:
rdnCmts.1.3.6.1.4.1.4981.2
56
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
56 total| Object Name |
|---|
rdnCmtsThis is the enterprise MIB Module for Motorola's
Cable Modem Termination Systems (CMTS). MODULE-IDENTITY .1.3.6.1.4.1.4981.2 |
RDN-MIBThis is the enterprise MIB Module for Motorola's
Cable Modem Termination Systems (CMTS). NOTIFICATION-TYPE .1.3.6.1.4.1.4981.2 |
rdnCmtsIfObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4981.2.1 |
rdnCmtsDownstreamChannelTableThis table describes the attributes of downstream
channel in addition to those specified by the docsIfMib. SEQUENCE OF RdnCmtsDownstreamChannelEntry .1.3.6.1.4.1.4981.2.1.1 |
rdnCmtsDownstreamChannelEntryAn entry provides a list of attributes for a single
Downstream channel.
An entry in this table exists for each ifEntry with an
ifType of docsCableDownstream(128). RdnCmtsDownstreamChannelEntry .1.3.6.1.4.1.4981.2.1.1.1 |
cmtsDSModulationThe attribute to control the down stream modulation. When this
object is set to FALSE(2), the downstream transmitter will output
a CW, or tonal signal at the tuned RF frequency.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4981.2.1.1.1.1 |
rdnCmtsUpstreamChannelTableThis table describes the attributes of upstream
channel in addition to those specified by the docsIfMib. SEQUENCE OF RdnCmtsUpstreamChannelEntry .1.3.6.1.4.1.4981.2.1.2 |
rdnCmtsUpstreamChannelEntryList of attributes for a single upstream channel.
An entry in this table exists for each ifEntry with an
ifType of docsCableUpstream(129). RdnCmtsUpstreamChannelEntry .1.3.6.1.4.1.4981.2.1.2.1 |
cmtsUSNominalRxPowerThe attribute to program the target, or nominal, receive power of
each upstream RF port. The range is channel width dependent:
Power Level Channel Width
-160,+140 200 kHz
-130,+170 400 kHz
-100,+200 800 kHz
-70,+230 1600 kHz
-40,+260 3200 kHzrw Integer32 (-160..260) .1.3.6.1.4.1.4981.2.1.2.1.1 |
rdnCmtsUSNominalRxPowerModeThis object describes the setting mode for rdnCmtsUSNomialRxPower.
The default setting is the absolute mode.rw Enumeration .1.3.6.1.4.1.4981.2.1.2.1.2 |
cmtsUSInvitedRangingIntervalTo fix Invited(Periodic) Ranging Intervals as in input to the
Bandwidth Allocator algorithm.rw Integer32 ( 0..30000 ) .1.3.6.1.4.1.4981.2.1.2.1.3 |
cmtsUSRangingResponseControlThe attribute to force all RNG-Resp messages to issue a 'Continue'
Ranging Status indefinitely regardless of timing, power, etc. accuracy
of previous incoming Ranging Request. Value 0 means Normal Ranging Mode,
value 1 means Status Overriderw Enumeration .1.3.6.1.4.1.4981.2.1.2.1.4 |
cmtsUSRangingPowerOverrideThe attribute overrides upstream power adjustments performed by the
CMTS to CM's. When this object is set to TRUE(1), the override is
activated, all Ranging Response message will be transmitted with
ZERO power adjustment, regardless of received upstream power
levels.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4981.2.1.2.1.5 |
rdnCmtsStpObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4981.2.1.3 |
rdnCmtsStpEnableThis object controls the activation of DOCSIS Spanning Tree Protocol
Bridging functionality. The Spanning Tree Bridging is disabled/enabled
by setting this object to FALSE/TRUE.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4981.2.1.3.1 |
rdnCmtsStpTCNEnableThis object controls the generation of Topology Change Notification
messages for DOCSIS Spanning Tree Protocol Bridge.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4981.2.1.3.2 |
rdnCmtsLinkUpdownTrapEnableTableThis table has the object to enable or disable the generation of
LinkUp and Link Down traps. SEQUENCE OF RdnCmtsLinkUpdownTrapEnableEntry .1.3.6.1.4.1.4981.2.1.4 |
rdnCmtsLinkUpdownTrapEnableEntryAn entry in this table exists for each ifEntry with an
ifType of docsCableUpstream(129). RdnCmtsLinkUpdownTrapEnableEntry .1.3.6.1.4.1.4981.2.1.4.1 |
rdnLinkUpDownTrapEnableIndicates whether linkUp and LinkDown traps should be
generated for this interface. By default, this object
should have the value disabled(2) for interfaces which do
not operate on 'top' of any other interface (as defined in
the ifStackTable), and enabled(1) otherwise. These traps
are convenient for knowing the Spectrum Group Name whenever
the link state changes. So the trap is only limited to the
ifIndex values related to upstream.rw Enumeration .1.3.6.1.4.1.4981.2.1.4.1.1 |
rdnCmtsMiscObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4981.2.2 |
rdnCmtsSaveConfigThis object when set to TRUE will save the current configuration of
the CMTS. When this object is read it will return FALSErw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4981.2.2.1 |
rdnCmtsCmResetByMacAddrThe CM MAC address that the operator wants to reset. When this object
is set, it will cause the CMTS to reset that CM. When this object is
read it will return zerorw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.4981.2.2.2 |
rdnCmtsCmResetByIpAddrThe CM IP address that the operator wants to reset. When this object
is set, it will cause the CMTS to reset that CM. When this object is
read it will return zerorw IpAddress .1.3.6.1.4.1.4981.2.2.3 |
rdnCmtsCmResetAllThis object when set to TRUE will cause the CMTS to reset all the CM that
are registered with this CMTS. When this object is read it will return
FALSErw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4981.2.2.4 |
rdnCmtsHostAuthControlThis object is used to add or delete entry in CMTS host authorization
table. The first octet is for action, add (1) or delete (2), the rest
are composed with CM MAC address (6 octets), CPE MAC address (6 octets),
and the CPE IP address (4 octets).
Zero is returned for read on this objectrw OCTET STRING .1.3.6.1.4.1.4981.2.2.5 |
rdnCmtsModemAgingTimerThe Time in minutes of modem inactivity after which the modem is
deleted from the registration table. The minimum is 10 minutes
and the maximum is 21 days. A value of '0' will disable the
aging timerrw Integer32 .1.3.6.1.4.1.4981.2.2.6 |
rdnCmtsCpeToCmObject OBJECT IDENTIFIER .1.3.6.1.4.1.4981.2.2.7 |
rdnCmtsCpeToCmTableThis table describes the mapping between CPE's MAC address
and MAC address of the cable modem these CPEs are attached to.
This table does not support the walk/getNext. It is not intended
to use this mib to walk the list of cpe's in the system. SEQUENCE OF RdnCmtsCpeToCmEntry .1.3.6.1.4.1.4981.2.2.7.1 |
rdnCmtsCpeToCmEntryAn entry describes the mapping between one CPE's MAC address
and MAC address of the cable modem this CPE is attached to. RdnCmtsCpeToCmEntry .1.3.6.1.4.1.4981.2.2.7.1.1 |
rdnCmtsCpeMacThis object is the MAC address of the CPE (host) that a cable
modem is attached to. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.4981.2.2.7.1.1.1 |
rdnCmtsCmMacThis object returns the MAC address of the cable modem that a CPE
(host) is attached to. If the CPE is not found being attached to any
cable modem registered on this CMTS, the read of this object will
return zero.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.4981.2.2.7.1.1.2 |
rdnIfCmtsCmStatusTableThis table is an extension of the docsIfCmtsCmStatusTable. It
provides additional information about the CM. SEQUENCE OF RdnIfCmtsCmStatusEntry .1.3.6.1.4.1.4981.2.2.8 |
rdnIfCmtsCmStatusEntryEach entry of the table rdnIfCmtsCmStatusTable. Each entry provides
some additonal information about the CM. RdnIfCmtsCmStatusEntry .1.3.6.1.4.1.4981.2.2.8.1 |
rdnIfCmtsCmStatusRegistrationTimeWhen read, this object will return the time in seconds since
the modem registered. If the modem is unregistered, it will
return ZEROro Integer32 .1.3.6.1.4.1.4981.2.2.8.1.1 |
rdnIfCmtsCmStatusTxUnicastBytesWhen read, this object will return the number of unicast bytes
the modem has transmitted. For offline modems this value is the
the total number of unicast bytes when it was online. This
object is never reset as long as the CMTS is up. It does not
need to be restored across reboots . However, when the CM
reregisters into a new spectrum group, this data must be
restored.ro Counter64 .1.3.6.1.4.1.4981.2.2.8.1.2 |
rdnIfCmtsCmStatusRxUnicastBytesWhen read, this object will return the number of unicast bytes
the modem has Received. For offline modems this value is the
the total number of unicast bytes when it was online. This
Object is never reset as long as the CMTS is up. It does not
need to be restored across reboots. However, when the CM
reregisters into a new spectrum group, this data must be
restored.ro Counter64 .1.3.6.1.4.1.4981.2.2.8.1.3 |
rdnIfCmtsCmStatusSpectrumGroupNameWhen read, this object will return the spectrum group name. If
data not available, return NULL stringro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4981.2.2.8.1.4 |
rdnIfCmtsCmStatusUpstreamPortThe Upstream Port Number the modem is using. For offline modems
this value is meaningless.ro INTEGER .1.3.6.1.4.1.4981.2.2.8.1.5 |
rdnIfCmtsCmStatusDownStreamPortThe downstream port number the modem is using, For offline
modems this value is meaningless.ro INTEGER .1.3.6.1.4.1.4981.2.2.8.1.6 |
rdnModemDeregReasonModem Deregistration Reason
normal - the CMTS has lost contact witht the modem.
operatorReset - reset by the operator
operatorDisabled - operator has disabled the modem
operatorDeleted - was removed from the system
transmissionFailed - the transmitter communicating to the modem
has failed
transmissionDisabled - the transmitter communicating to the modem
has been disabled
transmissionDeleted - the transmitter communicating to the modem
has been deleted
servingGroupChanged - the assignment of the serving groups for the
modem has changed
receiverFailed - the receiver communicating with the modem has
failed
receiverDisabled - the receiver communicating with the modem has
been disabled
receiverDeleted - the receiver communicating with the modem has
beeb deleted
channelDeleted - a channel has changed on the reciver that has
caused the modem to deregister
channelErrors - deregistered due to unacceptable amount of channel
errors
incompleteReg - deregistered due to incomplete registration
profileUpdateComplete - deregistered after profile update
skeyFailure - deregistered due to session key failure
dnChanChangeFailure - due to downstream transmission channel change failure
noDeregReason - no deregistration reason available
powerTolerance - power ranging corrections were out of tolerance
freqTolerance - frequency ranging corrections were out of tolerance
timingTolerance - timing ranging correction were out of tolerance
rangingTolerance - multiple ranging corrections were out of tolerance
noResponseUCC - modem did not respond to the UCC request
This is a place holder for the modem deregistration reason. This should
return ZERO when read. This just allows us to include a deregistration
reason in the modem deregistration trap varbind.ro Enumeration .1.3.6.1.4.1.4981.2.2.9 |
rdnDevCmtsTraps OBJECT IDENTIFIER .1.3.6.1.4.1.4981.2.2.10 |
rdnDevCmtsCmRegisteredTrapAn event to report the registration of a modem. The
values of docsDevEvLevel, docsDevId, and DocsDevEvText
are from the entry which logs this event in the
docsDevEventTable, DocsIfCmtsCmStatusDocsisMode and
docsIfCmtsCmStatusMacAddress indicate the docsis
version and the MAC address of the registered CM.
docsIfDocsisCapability indicate the docsis version of
the CMTS , docsIfUpChannelId, docsIfDownChannelId gives
the upstream and downstream channel id respectively
for the CM. rdnSpectrumGroupName gives the spectrum
group name. NOTIFICATION-TYPE .1.3.6.1.4.1.4981.2.2.10.1 |
rdnDevCmtsCmDeregisteredTrapAn event to report the registration of a modem. The
values of docsDevEvLevel, docsDevId, and DocsDevEvText
are from the entry which logs this event in the
docsDevEventTable, DocsIfCntsCmStatusDocsisMode and
docsIfCmtsCmStatusMacAddress indicate the docsis
version and the MAC address of the registered CM.
docsIfDocsisCapability indicate the docsis version of
the CMTS , docsIfUpChannelId, docsIfDownChannelId gives
the upstream and downstream channel id respectively
for the CM. rdnSpectrumGroupId gives the spectrum
group name. NOTIFICATION-TYPE .1.3.6.1.4.1.4981.2.2.10.2 |
rdnLinkUpTrapThe standard linkUp traps don't give out the spectrum group name.
So this is the trap that will extend the varbind to include the
spectrum group name. NOTIFICATION-TYPE .1.3.6.1.4.1.4981.2.2.10.3 |
rdnLinkDownTrapThe standard linkDown traps don't give out the spectrum group
name. So this is the trap that will extend the varbind to
include the spectrum group name. NOTIFICATION-TYPE .1.3.6.1.4.1.4981.2.2.10.4 |
rdnModemRegIndexThis is place holder for CMId which is the index to the CM table.
This table WILL contain the CM information. Right now the table is
not implemented yet. When read it returns ZERO. But in future this
should be part of the CM information table and this should be
removed from here. This is required now to support the varbind
in Registration and Deregistration Traps.ro Integer32 .1.3.6.1.4.1.4981.2.2.11 |
rdnCmToCpeTableThis table provides the information about the CPEs attached to the
CM. SEQUENCE OF RdnCmToCpeEntry .1.3.6.1.4.1.4981.2.2.12 |
rdnCmToCpeEntryAn entry of the table rdnCmToCpeTable. Each entry provides the
CPE Mac and IP addresses. RdnCmToCpeEntry .1.3.6.1.4.1.4981.2.2.12.1 |
rdnCmToCpeIndexIndex Value for an individual CPE, This index value is not
guarenteed to remain same during CMTS uptime. Integer32 .1.3.6.1.4.1.4981.2.2.12.1.1 |
rdnCmToCpeMacAddressThe Mac Address of the CPE attached to the CMro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.4981.2.2.12.1.2 |
rdnCmToCpeIpAddressThe IP Address of the CPE attached to the CMro IpAddress .1.3.6.1.4.1.4981.2.2.12.1.3 |
rdnCmtsRedunObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4981.2.3 |
rdnCmtsRedundancyEnableThis object enables or disables the redundant CM
card support.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4981.2.3.1 |
rdnCmtsRedundancySlotThis object selects which CMTS card to use as the
redundant hot-standby.rw Integer32 .1.3.6.1.4.1.4981.2.3.2 |
rdnCmtsRedundancyRevertTimeoutThe number of seconds to wait before reverting from
the redundant standby back to the CMTS card. If 0 is
specified then reverting is disabled.rw Integer32 .1.3.6.1.4.1.4981.2.3.3 |
rdnCmtsRedundancySwitchoverWriting to this object forces the specified CMTS card
to switchover to the redundant standby. Reading this
object does nothing and provides no information.rw Integer32 .1.3.6.1.4.1.4981.2.3.4 |
More MIBs from Riverdelta
Browse all RiverdeltaMIBs →RDN-PKTCABLE-GROUP-MIB
The RDN-PKTCABLE-GROUP-MIB provides management interfaces for Motorola PacketCable multimedia systems, specifically enabling the monitoring of cable modem termination system (CMTS) and media gateway components to track session states, voice quality parameters, and packet transport metrics defined by the PacketCable architecture.
157 objects→
RDN-CABLE-SPECTRUM-GROUP-MIB
The RDN-CABLE-SPECTRUM-GROUP-MIB enables MCNS-compliant Cable Modem Termination Systems (CMTS) to monitor and configure spectrum group parameters, including frequency allocations, channel bandwidths, and modulation profiles, for downstream and upstream cable transmission management.
72 objects→
RDN-EVT-NOTIFICATIONS
The RDN-EVT-NOTIFICATIONS module monitors critical and higher severity DOCSIS Cable Modem Termination System (CMTS) events by generating SNMP traps containing the calculated Event ID, severity level, and descriptive text. This mechanism enables network management systems to detect and correlate specific vendor-specific subsystem failures or status changes within Motorola-based DOCSIS infrastructure.
67 objects→
RDN-CHASSIS-MIB
The RDN-CHASSIS-MIB provides SNMP management capabilities for Motorola chassis hardware, enabling the monitoring of physical entity states, power supply status, fan module health, and temperature sensors. This module facilitates the retrieval of interface and module operational data to support fault detection and resource availability verification within the chassis infrastructure.
42 objects→
RDN-CABLE-SPECTRUM-MIB
The RDN-CABLE-SPECTRUM-MIB enables MCNS-compliant Cable Modem Termination Systems (CMTS) to monitor and manage RF spectrum parameters, including channel power levels, noise floor statistics, and upstream/downstream frequency allocations. This module facilitates the detection of spectral interference and the optimization of cable plant performance by exposing granular spectrum management data points for troubleshooting and capacity planning.
39 objects→
RDN-CHANNEL-BONDING-MIB
The RDN-CHANNEL-BONDING-MIB enables monitoring and management of Motorola cable modem termination systems and CMTS software to track downstream and upstream channel bonding parameters, including active channel counts, modulation profiles, and signal quality metrics. It facilitates the administration of bonded channel aggregation states and performance statistics essential for maintaining DOCSIS service delivery integrity.
29 objects→