POWERHUB-ATM-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for POWERHUB-ATM-MIB.
30
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
30 total| Object Name |
|---|
fore OBJECT IDENTIFIER .1.3.6.1.4.1.326 |
systems OBJECT IDENTIFIER .1.3.6.1.4.1.326.2 |
lsd OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.6 |
lsdproducts OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.6.1 |
powerhub4k6k7k OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.6.1.1 |
alchassis OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.6.1.1.1 |
alatm OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.6.1.1.2 |
atmLinkUpA LinkUp trap is sent by the ATM interface
while link up is dected. The slot id is reported
because individual virtual port number is not applicable
here. TRAP-TYPE .1.3.6.1.4.1.326.2.6.1.1.2.0.1 |
atmLinkDownA LinkDown trap is sent by the ATM interface
while link down is dected. The slot id is reported
because individual virtual port number is not applicable
here. TRAP-TYPE .1.3.6.1.4.1.326.2.6.1.1.2.0.2 |
atmCutOverA trap is sent if cut over is dected. The cut over
can be from primary to back or vice versa. TRAP-TYPE .1.3.6.1.4.1.326.2.6.1.1.2.0.3 |
atmBootUpA BootUp trap is sent by the ATM interface
while startup is dected. The slot id is reported
because individual virtual port number is not applicable
here. TRAP-TYPE .1.3.6.1.4.1.326.2.6.1.1.2.0.4 |
atmFaultA Fault trap is sent by the ATM interface
while a series of link down is dected. The slot id is reported
because individual virtual port number is not applicable
here. TRAP-TYPE .1.3.6.1.4.1.326.2.6.1.1.2.0.5 |
alAtmAMASlotTableA table that contains information about
AMA for ATM slot in the PowerHub 7000 chassis. SEQUENCE OF AlAtmAMASlotEntry .1.3.6.1.4.1.326.2.6.1.1.2.8 |
alAtmAMASlotEntryAMA information about a specific slot. AlAtmAMASlotEntry .1.3.6.1.4.1.326.2.6.1.1.2.8.1 |
alAtmAMASlotNumberThe slot number for which the following AMA
information applies.ro INTEGER .1.3.6.1.4.1.326.2.6.1.1.2.8.1.1 |
alAtmAMAUserSelectThe user specified AMA for normal operation.
Unless the user explicitly changes the AMA
assignments, the software uses the primary
AMA by default and the backup AMA only if
the link to the primary AMA fails.rw Enumeration .1.3.6.1.4.1.326.2.6.1.1.2.8.1.2 |
alAtmAMAActualUseThe AMA that is actually being used. If the
link to the primary AMA fails, this field
shows that the backup AMA is in use, even
though the primary AMA was selected for
use.ro Enumeration .1.3.6.1.4.1.326.2.6.1.1.2.8.1.3 |
alAtmAMAUTLevPrimeThe PHY UTOPIA level in use by the
PowerCell module and the Primary AMA.
UTOPIA is an ATM standard for
communication between the PowerCell
module and the PHY (AMA). The level can
be 1 or 2.ro INTEGER .1.3.6.1.4.1.326.2.6.1.1.2.8.1.4 |
alAtmAMAUTLevBackThe PHY UTOPIA level in use by the
PowerCell module and the Backup AMA.
UTOPIA is an ATM standard for
communication between the PowerCell
module and the PHY (AMA). The level can
be 1 or 2. Returns value '1000' if
Backup AMA is not installedro INTEGER .1.3.6.1.4.1.326.2.6.1.1.2.8.1.5 |
alAtmAMAUTVerPrimeThe version of the PHY UTOPIA in use by the
PowerCell module and the Primary AMA.ro INTEGER .1.3.6.1.4.1.326.2.6.1.1.2.8.1.6 |
alAtmAMAUTVerBackThe version of the PHY UTOPIA in use by the
PowerCell module and the Backup AMA. Returns
value '1000' if Backup AMA is not installedro INTEGER .1.3.6.1.4.1.326.2.6.1.1.2.8.1.7 |
alAtmAMAProtoPrimeThe PHY-layer protocol in use on the
Primary AMA. The protocol can be one
of the following:
155M OC3 - 155 Mb/s using an OC-3 connector
45M DS3 - 45 Mb/s using a DS3 connector
39M E3 - 39 Mb/s using an E3 connectorro Enumeration .1.3.6.1.4.1.326.2.6.1.1.2.8.1.8 |
alAtmAMAProtoBackThe PHY-layer protocol in use on the
Backup AMA. The protocol can be one
of the following:
155M OC3 - 155 Mb/s using an OC-3 connector
45M DS3 - 45 Mb/s using a DS3 connector
39M E3 - 39 Mb/s using an E3 connectorro Enumeration .1.3.6.1.4.1.326.2.6.1.1.2.8.1.9 |
alAtmAMAMediaPrimeThe type of cable connecting the Primary
AMA to the ATM switch. The cable type
can be one of the following:
CAT5 UTP
Coaxial Cable
Multimode Fiber
Single Mode Fiberro Enumeration .1.3.6.1.4.1.326.2.6.1.1.2.8.1.10 |
alAtmAMAMediaBackThe type of cable connecting the Backup
AMA to the ATM switch. The cable type
can be one of the following:
CAT5 UTP
Coaxial Cable
Multimode Fiber
Single Mode Fiberro Enumeration .1.3.6.1.4.1.326.2.6.1.1.2.8.1.11 |
alAtmPreviousAMAThe AMA that is actually being used before
link down or cut over. The initial value
is notset.ro Enumeration .1.3.6.1.4.1.326.2.6.1.1.2.8.1.12 |
alAtmPreviousAMATypeThe PHY-layer protocol in use before
link down or cut-over.
The protocol can be one of the following:
155M OC3 - 155 Mb/s using an OC-3 connector
45M DS3 - 45 Mb/s using a DS3 connector
39M E3 - 39 Mb/s using an E3 connector.ro Enumeration .1.3.6.1.4.1.326.2.6.1.1.2.8.1.13 |
alAtmCurrentAMATypeThe PHY-layer protocol actually in use.
The protocol can be one of the following:
155M OC3 - 155 Mb/s using an OC-3 connector
45M DS3 - 45 Mb/s using a DS3 connector
39M E3 - 39 Mb/s using an E3 connector.ro Enumeration .1.3.6.1.4.1.326.2.6.1.1.2.8.1.14 |
powerbits OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.6.1.2 |
lsdcommon OBJECT IDENTIFIER .1.3.6.1.4.1.326.2.6.2 |