POWERCONNECT5012-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for POWERCONNECT5012-MIB.
109
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
109 total| Object Name |
|---|
dell OBJECT IDENTIFIER .1.3.6.1.4.1.674 |
IMPORTS Unknown .1.3.6.1.4.1.674 |
addressIntrusionAn addressIntrusion trap signifies that an
unauthorized address has been seen on the network. TRAP-TYPE .1.3.6.1.4.1.674.0.0 |
dellLan OBJECT IDENTIFIER .1.3.6.1.4.1.674.10895 |
powerconnect5012 OBJECT IDENTIFIER .1.3.6.1.4.1.674.10895.2 |
dellCommGroup OBJECT IDENTIFIER .1.3.6.1.4.1.674.10895.2.1 |
commTableA list of SNMP Community Entries SEQUENCE OF CommEntry .1.3.6.1.4.1.674.10895.2.1.1 |
commEntryA list of SNMP Community properties CommEntry .1.3.6.1.4.1.674.10895.2.1.1.1 |
commIndexAn index that uniquely identifies an entry in the
Community Table. Eight entries are currently supported.ro INTEGER .1.3.6.1.4.1.674.10895.2.1.1.1.1 |
commNameThe name of this SNMP Community Entry.rw DisplayString .1.3.6.1.4.1.674.10895.2.1.1.1.2 |
commGetThe GET permission for the community. A (1) indicates a
GET enable. A (2) indicates a GET disable.rw Enumeration .1.3.6.1.4.1.674.10895.2.1.1.1.3 |
commSetThe SET permission for the community. A (1) indicates a
SET enable. A (2) indicates a SET disable.rw Enumeration .1.3.6.1.4.1.674.10895.2.1.1.1.4 |
commTrapThe TRAP permission for the community. A (1) indicates a
TRAP enable. A (2) indicates a TRAP disable.rw Enumeration .1.3.6.1.4.1.674.10895.2.1.1.1.5 |
commStatusThe RowStatus for the community entry.rw INTEGER .1.3.6.1.4.1.674.10895.2.1.1.1.6 |
dellHostGroup OBJECT IDENTIFIER .1.3.6.1.4.1.674.10895.2.2 |
hostTableA list of SNMP Trusted Host Entries SEQUENCE OF HostEntry .1.3.6.1.4.1.674.10895.2.2.1 |
hostEntryA list of SNMP Host properties HostEntry .1.3.6.1.4.1.674.10895.2.2.1.1 |
hostIndexAn index that uniquely identifies an entry in the
Host Table. Sixteen entries are currently supported.ro INTEGER .1.3.6.1.4.1.674.10895.2.2.1.1.1 |
hostNameThe name of this Host Entry.rw DisplayString .1.3.6.1.4.1.674.10895.2.2.1.1.2 |
hostIPThe IP Address for the host.rw IpAddress .1.3.6.1.4.1.674.10895.2.2.1.1.3 |
hostCommThe name of the community this host belongs to.rw DisplayString .1.3.6.1.4.1.674.10895.2.2.1.1.4 |
hostStatusThe RowStatus for the community entry.rw INTEGER .1.3.6.1.4.1.674.10895.2.2.1.1.5 |
hostAuthorizationIf enabled, the host must be in the hostTable in order
to access the device via SNMP.rw Enumeration .1.3.6.1.4.1.674.10895.2.2.2 |
dellMiscGroup OBJECT IDENTIFIER .1.3.6.1.4.1.674.10895.2.3 |
miscBaudThe Serial port BAUD Rate.ro INTEGER .1.3.6.1.4.1.674.10895.2.3.1 |
miscResetPhysically resets the unit - use with care. A (1) resets
the unit, a (2) does nothing.rw Enumeration .1.3.6.1.4.1.674.10895.2.3.2 |
miscStatisticsResetResets the units statistics. A (1) resets
the unit, a (2) does nothing.rw Enumeration .1.3.6.1.4.1.674.10895.2.3.3 |
miscSwitchOperStateGlobal operation state of the switch.ro Enumeration .1.3.6.1.4.1.674.10895.2.3.4 |
dellSpanGroup OBJECT IDENTIFIER .1.3.6.1.4.1.674.10895.2.4 |
spanOnOffEnable/Disable Spanning Tree. A (1) enables, a (2) disables.rw Enumeration .1.3.6.1.4.1.674.10895.2.4.1 |
dellConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.674.10895.2.11 |
configVerSwPrimaryThe software image version stringro DisplayString .1.3.6.1.4.1.674.10895.2.11.1 |
configVerHwChipSetThe hardware chipset version stringro DisplayString .1.3.6.1.4.1.674.10895.2.11.2 |
configBootModeDefines the method used for downloading the image when reset.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.3 |
configBootFtpServerIpThe FTP server's IP address used for downloading the
boot imagerw IpAddress .1.3.6.1.4.1.674.10895.2.11.4 |
configBootImageFileNameThe path and filename of the boot image to downloadrw DisplayString .1.3.6.1.4.1.674.10895.2.11.5 |
configPortTableA list of interface entries used for enterprise specific
configuration. The number of entries is given by the value
of ifNumber. All interface entries are assumed to be
Ethernet interafaces. SEQUENCE OF ConfigPortEntry .1.3.6.1.4.1.674.10895.2.11.6 |
configPortEntryAn enterprise specific interface entry. ConfigPortEntry .1.3.6.1.4.1.674.10895.2.11.6.1 |
configPortA unique value for each interface that correlates to ifIndex.
Its value ranges between 1 and the value of ifNumber.rw INTEGER .1.3.6.1.4.1.674.10895.2.11.6.1.1 |
configPortDuplexThe port's duplex desired state.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.6.1.3 |
configPortRuntFiltDefines whether the port will drop runt packetsrw Enumeration .1.3.6.1.4.1.674.10895.2.11.6.1.4 |
configPortSrcSecurityThe desired state for an interface's source security.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.6.1.5 |
configPortDataRateThe port's desired transmission data rate.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.6.1.6 |
configForwardingModeIndicates whether the packets will receive the entire
packet before forwarding. 'store-and-forward'
receives the entire packet before forwarding.
'cut-through' may forward the packet before the
entire packet is received.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.6.1.7 |
configPortDuplexOperThe port's duplex state.ro Enumeration .1.3.6.1.4.1.674.10895.2.11.6.1.8 |
configPortDataRateOperThe port's transmission data rate.ro Enumeration .1.3.6.1.4.1.674.10895.2.11.6.1.9 |
configPortStateOperThe port's current state.ro Enumeration .1.3.6.1.4.1.674.10895.2.11.6.1.10 |
configPortFlowControlThe port will avoid transmitting a new packet
for the period of time specified in a received
PAUSE packet when enabled.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.6.1.11 |
configPortDefaultVlanIdThe port will add this vlan id tag to any incoming packet
which is lacking a vlan id tag.rw INTEGER .1.3.6.1.4.1.674.10895.2.11.6.1.12 |
configPortCommentsMay contain any comments related to a given port such as
a user name or LAN segment.rw DisplayString .1.3.6.1.4.1.674.10895.2.11.6.1.13 |
configPortAutoNegotiationThe port will perform auto-negotiation to determine the
port's duplex and data rate. When auto-negotiation is
enabled, the negotiated duplex and data rate can be
determined by configPortDuplexOper and
configPortDataRateOper mib objects respectively.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.6.1.14 |
configPortHOLBlockingWhen enabled, the port will prevent head-of-line blocking
from occuring. If the current port is to forward a packet
to a port which is beleived to be blocked, the packet will
be dropped instead of forwarded.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.6.1.15 |
configPortFlowControlOperThe port's current flow control state.ro Enumeration .1.3.6.1.4.1.674.10895.2.11.6.1.16 |
configPortGBICPort Type.rw INTEGER .1.3.6.1.4.1.674.10895.2.11.6.1.17 |
configPortFastLinkThe port's FastLink option.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.6.1.18 |
configPortPriorityThe port's current flow control state.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.6.1.19 |
configRmonOnOffEnable or disable Remote Montioring, RMON.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.7 |
configMirroringOnOffEnable or disable port mirroring.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.8 |
configMirrorSrcWhen mirroring is enabled (configMirroringOnOff =
enabled), this identifies the mirroring source port.
This value has a valid range of 1 to ifNumber when enbaled.rw INTEGER .1.3.6.1.4.1.674.10895.2.11.9 |
configMirrorMonWhen mirroring is enabled (configMirroringOnOff =
enabled), this identifies the mirroring monitoring
port. This value has a valid range of 1 to ifNumber when
enabled.rw INTEGER .1.3.6.1.4.1.674.10895.2.11.10 |
configIpAssignmentModeIndicates whether the device address is assigned by
the user (manual), BootP, or DHCP.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.12 |
configPhysAddressThe interface's address at the protocol layer
immediately 'below' the network layer in the
protocol stack. This is the physical address
for the end-station.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.674.10895.2.11.13 |
configPasswordUserThe user password.rw DisplayString .1.3.6.1.4.1.674.10895.2.11.14 |
configPasswordAdminThe adminstrator passwordrw DisplayString .1.3.6.1.4.1.674.10895.2.11.15 |
configIpAddressThe IP Address for the RDU box.rw IpAddress .1.3.6.1.4.1.674.10895.2.11.16 |
configNetMaskThe network mask for the RDU box.rw IpAddress .1.3.6.1.4.1.674.10895.2.11.17 |
configGatewayThe Gatway Address for the RDU box.rw IpAddress .1.3.6.1.4.1.674.10895.2.11.18 |
configSavePhysically saves the current configuration to nvram.
- use with care.
(1) saves the configuration
(2) does nothing.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.19 |
configVerifyPasswordVerify the password is valid. If invalid a BAD_VALUE
error is returned.rw DisplayString .1.3.6.1.4.1.674.10895.2.11.20 |
configVerBootRomImageThe Boot ROM version stringro DisplayString .1.3.6.1.4.1.674.10895.2.11.21 |
configRestoreDefaultsRestores the configuration of the unit to the
original settings.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.22 |
configIGMPOnOffEnable or disable the IGMP protocol within the switch.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.23 |
configWebOnOffEnable or disable the Web Interface.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.24 |
configHighPriorityOptimizationEnable or disable high priority optimization.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.25 |
configDynamicAddressLearningThe ablility to learn dynamic addresses automatically.
With this parameter disabled, a new address detected on
a port will cause that port to be disabled, force a
configuration save, and issue a trap alerting
management stations of the intrusion.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.26 |
configUserAuthenticationModeDetermines whether the user password will be authenticated
by the switch, a remote RADIUS server, or some combination
of the two.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.27 |
configRadiusServerIpAddressThe IP Address of the RADIUS server used for remote
user authentication.rw IpAddress .1.3.6.1.4.1.674.10895.2.11.28 |
configRadiusSharedSecretA string of characters used in the RADIUS password
encryption process.rw DisplayString .1.3.6.1.4.1.674.10895.2.11.29 |
configTelnetConsoleEnable or disable the telnet console.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.30 |
configDiffServTableA list of DSCP Priorities. SEQUENCE OF ConfigDiffServEntry .1.3.6.1.4.1.674.10895.2.11.31 |
configDiffServEntryAn enterprise specific DSCP entry. ConfigDiffServEntry .1.3.6.1.4.1.674.10895.2.11.31.1 |
configDiffServDSCPA DSCP value.ro INTEGER .1.3.6.1.4.1.674.10895.2.11.31.1.1 |
configDiffServPriorityThe DSCP's current priority setting.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.31.1.2 |
configTftpServerIpAddressThe IP Address of the tftp server used to upload and
download configuration files. This object is to be used
in conjunction with configTftpServerFileName and
configTftpOperation.rw IpAddress .1.3.6.1.4.1.674.10895.2.11.32 |
configTftpServerFileNameThe filename, including the path, used to store or
retrieve a configuration file from the tftp server.
This object is to be used in conjunction with
configTftpServerIpAddress and configTftpOperation.rw DisplayString .1.3.6.1.4.1.674.10895.2.11.33 |
configTftpOperationThe tftp operation to perform. Either download a
configuration to the unit or upload the current
configuration to the tftp server. This object is
to be used in conjunction with
configTftpServerIpAddress and configTftpServerFileName.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.34 |
configIpFilterDetermines if access to the device is limited to only
those IP addresses specified in the configIpFilterTable.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.35 |
configIpFilterTableA list of IP addresses allowed access to this device. SEQUENCE OF ConfigIpFilterEntry .1.3.6.1.4.1.674.10895.2.11.36 |
configIpFilterEntryAn enterprise specific IP filter entry. ConfigIpFilterEntry .1.3.6.1.4.1.674.10895.2.11.36.1 |
configIpFilterIpAddressAn IP address which is allowed access to this device.ro IpAddress .1.3.6.1.4.1.674.10895.2.11.36.1.1 |
configIpFilterStatusThe status of an entry in the IP filter Table. Only
a subset of the rowstatus variables (active, destroy)
are available.rw Enumeration .1.3.6.1.4.1.674.10895.2.11.36.1.2 |
dellVlanGroup OBJECT IDENTIFIER .1.3.6.1.4.1.674.10895.2.13 |
vlanTableA list of the VLANs SEQUENCE OF VlanEntry .1.3.6.1.4.1.674.10895.2.13.1 |
vlanEntryA VLAN entry containing the VLAN id and name. VlanEntry .1.3.6.1.4.1.674.10895.2.13.1.1 |
vlanIdThe VLAN identifier. A maximum of 16 VLANs is supported.
The value must be from 0 to 4095.ro INTEGER .1.3.6.1.4.1.674.10895.2.13.1.1.1 |
vlanNameThe VLAN name associated with the VLAN Id.rw DisplayString .1.3.6.1.4.1.674.10895.2.13.1.1.2 |
vlanStatusThe status of an entry in the VLAN Table. Only a subset
of the rowstatus variables (active, createAndGo, destroy)
are available.rw Enumeration .1.3.6.1.4.1.674.10895.2.13.1.1.3 |
vlanPortTableA list of ports and their associated VLAN. SEQUENCE OF VlanPortEntry .1.3.6.1.4.1.674.10895.2.13.2 |
vlanPortEntryInformation pertaining to an individual port regarding
to which VLAN it belongs. VlanPortEntry .1.3.6.1.4.1.674.10895.2.13.2.1 |
vlanPortPortIdA port identifier that is in the range of 1 to ifNumber.ro INTEGER .1.3.6.1.4.1.674.10895.2.13.2.1.1 |
vlanPortVlanIdThe VLAN identifier.ro INTEGER .1.3.6.1.4.1.674.10895.2.13.2.1.2 |
vlanPortStatusThe status of this port's association within this VLAN. Only
a subset of the rowstatus variables (active, createAndGo,
destroy) are available.rw Enumeration .1.3.6.1.4.1.674.10895.2.13.2.1.3 |
vlanPortTaggedModeThe tagged mode of a VLAN port.rw Enumeration .1.3.6.1.4.1.674.10895.2.13.2.1.4 |
dellPortTrunkGroup OBJECT IDENTIFIER .1.3.6.1.4.1.674.10895.2.14 |
portTrunkTableA list of port trunks and their associated members. SEQUENCE OF PortTrunkEntry .1.3.6.1.4.1.674.10895.2.14.1 |
portTrunkEntryA port trunk entry containing the trunk id and trunk members. PortTrunkEntry .1.3.6.1.4.1.674.10895.2.14.1.1 |
portTrunkIdThe port trunk identifier. The current range is from 1 to 4.ro INTEGER .1.3.6.1.4.1.674.10895.2.14.1.1.1 |
portTrunkMemberA port trunk has four members.ro INTEGER .1.3.6.1.4.1.674.10895.2.14.1.1.2 |
portTrunkMemberValueA port trunk member value indicates which port is a
member of the specified trunk. Valid values are in the
range from 0 to ifNumber. A zero indicates that no port
is contained in the specifed member.rw INTEGER .1.3.6.1.4.1.674.10895.2.14.1.1.3 |